DMV - Maroon Tubes

N°	§ N°	U/AI	CR	Date	Comment	Status
1	4.5	AI	No	add date	No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or confirmed. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx	Open
2	10.1	AI	No	add date	MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...	Open
3	4.5	AI	No	add date	No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx	Open
4	4.1	AI	No	add date	Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...	Open
5	4.4.1	AI	No	add date	No evidence confirms metallographic preparation and examination are performed according to ISO 17781 with the specified etchant solution for 25 Cr Duplex stainless steels as required. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_S...	Open
6	10.2	AI	No	add date	EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...	Open
7	8.0	AI	No	add date	Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc	Open
8	4.1	AI	No	add date	Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions, is fulfilled for DMV 25.7N. The or...	Open
9	10.2	AI	No	add date	Most documentation and certification requirements are addressed, including NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but the actual steel producer's name is not provided (only country of origin), and...	Open
10	3.1	AI	No	add date	AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
11	4.2	AI	No	add date	Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...	Open
12	1.0	AI	No	add date	DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...	Open
13	4.4.1	AI	No	add date	No information is provided regarding metallographic preparation and examination per ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels; grain size examination is only discussed for austenitic materials and is not applicab...	Open
14	4.2	AI	No	add date	DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...	Open
15	1.0	AI	No	add date	Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; full qualification to NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR is not confirmed. Source: DMV_STANDARD_BOOK/02...	Open
16	4.4.1	AI	No	add date	No evidence of use of 20-40% NaOH or KOH solution or other suitable etchants as per ISO 17781 Appendix B for micrographic examination; requirement not addressed for ferrite balance and intermetallic phases. Source: DMV_STANDARD_BOOK/12 - Special Test...	Open
17	4.3	AI	No	add date	Charpy V-notch testing is feasible and fulfills the requirement as the pipe wall thickness exceeds the minimum required by ASTM and ISO standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-0...	Open
18	3.0	AI	No	add date	MST-Tubes is NORSOK M-650 accredited for DMV 25.7N (UNS S32760) up to 31.75 mm WT, and the requirement is for 18.26 mm WT. The manufacturing process is qualified to NORSOK M-650 or ISO 17782, with qualification testing per NORSOK M-630 MDS D51 rev. 6...	Open
19	4.5	AI	No	add date	DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...	Open
20	4.3	AI	No	add date	DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energy values for both transverse and longitudinal directions, and the specified pipe dimensions allow for required testing directions and spec...	Open
21	3.1	AI	No	add date	AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
22	5.2	AI	No	add date	NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/650 are not confirmed as fulfilled. For OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at extra cost. Dye penetrant testing is limi...	Open
23	4.4.2	AI	No	add date	The microstructure must be basically free from intermetallic precipitates, but isolated precipitates are allowed if not distributed over the whole specimen and if the dimension of each precipitate is below 10 μm, matching the requirement exactly. Sou...	Open
24	4.5	AI	No	add date	DMV 25.7N meets ISO 17781: G48 Method A at 50°C for 24h, with no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...	Open
25	4.4.1	AI	No	add date	Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...	Open
26	3.1	AI	No	add date	DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as per Table 2 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
27	4.4.1	AI	No	add date	Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...	Open
28	3.2	AI	No	add date	Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...	Open
29	5.2	AI	No	add date	No provided document explicitly confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair; NDE acceptance criteria and required testing are not demonstrably fulfilled for the specified produc...	Open
30	4.4.2	AI	No	add date	Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...	Open
31	4.1	AI	No	add date	One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...	Open
32	6.0	AI	No	add date	Dimensional tolerances are specified as per the applicable ASTM standard (ASTM A790 referencing ASTM A999) for the relevant dimensions, with no overriding requirements from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.d...	Open
33	4.4.2	AI	No	add date	No information or documentation is provided regarding the recording and micrographic documentation (at 400x minimum) of intermetallic phases; the requirement is not addressed or fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destru...	Open
34	10.0	AI	No	add date	No evidence of an ISO 9001 or equivalent quality-assurance system certified by a competent EEA body is provided for the Montbard plant or manufacturer. No certification details or confirmation are present in the referenced documents or excerpts. Sour...	Open
35	3.2	AI	No	add date	Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...	Open
36	4.3	AI	No	add date	Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, exceeding the minimum wall thickness required for testing. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc	Open
37	4.4.2	AI	No	add date	Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...	Open
38	4.1	AI	No	add date	Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...	Open
39	7.0	AI	No	add date	ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: ASTM A 790, NORSOK MDS D51 Rev 06.	Open
40	4.4.2	AI	No	add date	No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at actual magnification with a scale bar if intermetallic phases are not detected; reporting requirements are not directly addressed or confirmed in t...	Open
41	10.1	AI	No	add date	No evidence that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification or that documentation will be submitted to TechnipFMC for approval. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 ...	Open
42	4.1	AI	No	add date	One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, with test frequency 1/lot matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specific...	Open
43	4.4.1	AI	No	add date	Etching by 20 to 40% NaOH or KOH is used to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...	Open
44	4.4.2	AI	No	add date	Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...	Open
45	8.0	AI	No	add date	Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot, in accordance with ASTM A790 and standard practice at Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, ...	Open
46	4.4.3	AI	No	add date	Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
47	4.4.2	AI	No	add date	Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria based on CVN and corrosion...	Open
48	4.1	AI	No	add date	Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests, with specified locations and directions, is fulfilled for DMV 25.7N per ...	Open
49	9.0	AI	No	add date	Weld repairs are explicitly stated as not acceptable under 'Surface finish / Repairs of defects' (§13, §14) for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 -...	Open
50	4.4.2	AI	No	add date	The digest allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size. Requirement not fully fulfilled. Source: DMV_S...	Open
51	4.2	AI	No	add date	Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...	Open
52	10.0	AI	No	add date	MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA and specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...	Open
53	4.4.2	AI	No	add date	No provided documents address the presence, reporting, or acceptance criteria for centerline intermetallic stringers, nor do they link acceptance to CVN and corrosion test results in such cases. Requirement not fulfilled based on available informatio...	Open
54	10.1	AI	No	add date	Certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, demonstrating qualification for the size and product...	Open
55	4.5	AI	No	add date	No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or specified. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx	Open
56	4.4.3	AI	No	add date	Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...	Open
57	4.2	AI	No	add date	DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...	Open
58	10.1	AI	No	add date	MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...	Open
59	4.4.2	AI	No	add date	Referenced specifications allow isolated intermetallic precipitates below 10µm and do not enforce a complete prohibition of intermetallic phases/precipitates if CVN testing cannot be completed, which is stricter in the client requirement. No document...	Open
60	10.2	AI	No	add date	No evidence that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC as specified in the requirement. Certification and inspection documents are referenced, but explicit fulfillment is not demonstrated for...	Open
61	4.1	AI	No	add date	Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...	Open
62	4.4.2	AI	No	add date	Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...	Open
63	5.1	AI	No	add date	No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...	Open
64	4.4.3	AI	No	add date	Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Structure must be basically free from intermetallic precipitates, with isolated precipitates allowed if ...	Open
65	4.3	AI	No	add date	Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...	Open
66	10.1	AI	No	add date	MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV 25.7N up to WT = 31.75 mm, covering the requested size, and the EN 10204 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number. Sour...	Open
67	4.4.3	AI	No	add date	No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Micrographic Examination/12-03-03 - Grain Size Ex...	Open
68	4.4.3	AI	No	add date	Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...	Open
69	4.3	AI	No	add date	DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for both test orientations. Source: DMV_ST...	Open
70	10.2	AI	No	add date	MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to the delivered products, fulfilling the documentation and traceability requirement as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...	Open
71	4.4.3	AI	No	add date	No acceptance criteria for micrographic examination are provided or applicable for DMV 25.7N (super-duplex stainless steel); grain size examination is not required for this material and is not addressed in the referenced standards or digests. Source:...	Open
72	10.2	AI	No	add date	Material certificate is issued according to EN 10204 Type 3.1 and validated by Quality Control for mill inspection; compliance with ASTM A790 and NORSOK M-630 information is not explicitly confirmed but certificate type and process are compliant. Sou...	Open
73	4.1	AI	No	add date	Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions. For the ord...	Open
74	4.4.3	AI	No	add date	Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
75	4.5	AI	No	add date	No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx	Open
76	4.4.1	AI	No	add date	Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...	Open
77	10.2	AI	No	add date	EN 10204 Type 3.1 certificates are issued as standard and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-...	Open
78	4.4.3	AI	No	add date	Ferrite content requirement of 35% to 60% is explicitly specified and confirmed for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D41 Re...	Open
79	4.2	AI	No	add date	Tensile testing is performed per ASTM A370 or ISO 6892-1 at room temperature, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...	Open
80	4.4.2	AI	No	add date	Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK/0...	Open
81	4.5	AI	No	add date	DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...	Open
82	4.4.1	AI	No	add date	Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination in accordance with the requirement. Source: DMV_STANDARD_BOOK/02 - Specificati...	Open
83	10.2	AI	No	add date	Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive te...	Open
84	4.5	AI	No	add date	No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx	Open
85	4.5	AI	No	add date	DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...	Open
86	4.4.2	AI	No	add date	Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...	Open
87	1.0	AI	No	add date	DMV 25.7N (UNS S32760) seamless pipes are manufactured and tested in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, meeting all relevant mechanical, chemical, and testing standards. Source: DMV_STAND...	Open
88	4.5	AI	No	add date	No specific acceptance criteria for metallurgical properties are provided in the referenced documents or section; only headings or general references are present without detailed requirements or limits. Source: DMV_STANDARD_BOOK/02-03-01 - Digest AST...	Open
89	4.2	AI	No	add date	DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...	Open
90	4.4.2	AI	No	add date	Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...	Open
91	5.1	AI	No	add date	No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled. Source: DMV_STANDARD_BOOK/12-02-01 - Non ...	Open
92	4.4.2	AI	No	add date	Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and the presence and location of intermetallic phases are noted and recorded with micrographs. Source: DMV_STANDARD_BO...	Open
93	1.0	AI	No	add date	No evidence that the supplier is qualified to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of the availability of the full Qualification Test Record/MPCR for review as required by the specification. ISO 17782 accre...	Open
94	4.5	AI	No	add date	Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria: no pitting at 20X magnification and weight loss < 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...	Open
95	4.3	AI	No	add date	Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions (18.26mm WT, 219.1mm OD). Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc	Open
96	4.4.2	AI	No	add date	Micrographs at a minimum magnification of 400x are included, with actual magnification and scale bar, fulfilling the requirement for representative micrographs at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDA...	Open
97	5.2	AI	No	add date	100% ultrasonic testing for longitudinal defects is performed in accordance with ASTM E213 and ISO 10893-10 after all mechanical processing, heat treatments, and straightening, and the dimensional range of the requested pipe is supported. Source: DMV...	Open
98	4.4.2	AI	No	add date	Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...	Open
99	3.0	AI	No	add date	MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 and meets NORSOK MDS D51 Rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...	Open
100	5.1	AI	No	add date	No provided documents mention the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDARD_B...	Open
101	10.2	AI	No	add date	No provided documents include NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or results of required metallurgical and non-destructive testing as specified. Only gen...	Open
102	4.4.3	AI	No	add date	Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
103	5.2	AI	No	add date	NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not fully addressed; only ASTM A790/ASTM A999 requirements are confirmed. For the specified OD, standard NDE methods at Montbard are either not feasible or only ava...	Open
104	4.4.2	AI	No	add date	Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_ST...	Open
105	3.1	AI	No	add date	AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N complies with the required chemical analysis. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NOR...	Open
106	5.2	AI	No	add date	No provided document explicitly states that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor confirms that the required NDE will be performed as standard for the specified pi...	Open
107	4.4.2	AI	No	add date	The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...	Open
108	3.1	AI	No	add date	MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the requested WT of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest ...	Open
109	5.2	AI	No	add date	Pipe dimensions are within ultrasonic testing capability, but there is no confirmation that testing is performed after all processing or that calibration notches meet ASTM E213 Figure 3 requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...	Open
110	7.0	AI	No	add date	ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx	Open
111	6.0	AI	No	add date	Dimensional tolerances are per ASTM A790 and referenced ASTM A999, as required, with no overriding specifications indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01...	Open
112	4.4.3	AI	No	add date	Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...	Open
113	3.2	AI	No	add date	Pipes are solution annealed followed by accelerated cooling per ASTM A790, manufacturing process is qualified to NORSOK M-650, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compliance with th...	Open
114	5.2	AI	No	add date	100% qualitative anti-mixing PMI checks are standard at Montbard, with quantitative PMI and procedures available if required, meeting general NDE acceptance criteria for PMI. Source: DMV_STANDARD_BOOK/12-06-06 - Positive Material Identification (PMI)...	Open
115	1.0	AI	No	add date	DMV 25.7N is a 25 Cr Duplex stainless steel seamless pipe fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all referenced mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thicknes...	Open
116	7.0	AI	No	add date	ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx	Open
117	4.4.3	AI	No	add date	Micrographic examination is specified per ISO 17781 with required etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requirement fo...	Open
118	4.1	AI	No	add date	Tensile and hardness tests are performed, but there is no evidence that impact, corrosion, and microstructure examinations are carried out for each heat and heat treatment lot as required by ASTM A790. No explicit confirmation of all required tests p...	Open
119	8.0	AI	No	add date	Marking per ASTM A790 and plant marking methods include heat number and lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02...	Open
120	8.0	AI	No	add date	Marking per ASTM A790 includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Marking methods (indelible ink, vibro-etching) are standard and applied as specified. Source: DMV_STANDARD_BOOK/02-04-03 - Diges...	Open
121	4.4.3	AI	No	add date	Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...	Open
122	4.1	AI	No	add date	None of the provided documents outline the test specimens sampling as required in Table 3 or reproduce its details; only a reference to Table 3 is made without specifying the sampling procedure or content of the table itself. Source: DMV_STANDARD_BOO...	Open
123	5.2	AI	No	add date	No provided document confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor is there confirmation that the required NDE is standardly performed or feasible for the sp...	Open
124	9.0	AI	No	add date	NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable' for seamless pipes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
125	9.0	AI	No	add date	Weld repairs are not acceptable as explicitly required for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
126	4.5	AI	No	add date	No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx	Open
127	4.1	AI	No	add date	Test sampling requirements for test directions, CVN impact testing, and thickness locations per Table 3 are not fully addressed; test direction for tensile and inclusion of CVN impact tests are not specified in the provided documents. Source: DMV_STA...	Open
128	6.0	AI	No	add date	Dimensional tolerances for OD, WT, and ovality are confirmed as per the applicable ASTM standards (including ASTM A 790 with A 999) for the requested dimensions, with no overriding TechnipFMC part report or drawing specified. Source: DMV_STANDARD_BOO...	Open
129	7.0	AI	No	add date	ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: ASTM A 790, NORSOK MDS D51 Rev 06.	Open
130	10.0	AI	No	add date	MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...	Open
131	4.5	AI	No	add date	DMV 25.7N complies with all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive, micrographic, ferrite, corrosion, and impact tests, with required tests and acceptance values matched. Source: DMV_STANDARD_BOOK/02 - Speci...	Open
132	4.2	AI	No	add date	Tensile testing is performed per ASTM A370, with results meeting or exceeding Table 4 requirements (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%), and hardness testing is also conducted as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...	Open
133	7.0	AI	No	add date	Pipes are required to be pickled or bright annealed according to ASTM A790 and NORSOK MDS S01, fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790, NORSOK MDS S01.	Open
134	1.0	AI	No	add date	Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence provided for availability of QTR/MPCR for review as required by the specification. Source: DMV_STANDARD_BOOK/02 - Specifications...	Open
135	4.4.2	AI	No	add date	The referenced specifications allow isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not meet the stricter requirement that intermetallic phases and/or precipitates are not permitted at all if CVN ...	Open
136	1.0	AI	No	add date	DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification listing and digest, including all mechanical, chemical, and testing requirements. Manufacturing is M-650 qualified for the ...	Open
137	10.1	AI	No	add date	MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...	Open
138	4.5	AI	No	add date	DMV 25.7N complies with ISO 17781 G48 Method A, meeting the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest...	Open
139	4.2	AI	No	add date	Mechanical property values (tensile strength, yield strength, elongation, hardness) required for DMV 25.7N are not explicitly confirmed in the provided documentation; referenced values are either missing or pertain to a different grade (TP316/316L). ...	Open
140	8.0	AI	No	add date	Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13 - Marking/13-02 - Standard marking feasibility/13-02-01 - Standard marking feasibility - Montbard plant/13...	Open
141	3.0	AI	No	add date	MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...	Open
142	1.0	AI	No	add date	Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782, as required. No evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
143	3.0	AI	No	add date	MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...	Open
144	10.1	AI	No	add date	MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demonst...	Open
145	5.1	AI	No	add date	No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...	Open
146	4.3	AI	No	add date	Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, meeting the minimum wall thickness requirements for both ASTM and ISO standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Dest...	Open
147	3.1	AI	No	add date	AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
148	10.2	AI	No	add date	ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...	Open
149	5.2	AI	No	add date	100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 or ISO 10893-10 is feasible and standards-compliant for the specified pipe dimensions; calibration notches are expected to follow ASTM E213 as the standard is accepted. Sou...	Open
150	4.3	AI	No	add date	The pipe dimensions allow for transverse Charpy specimens, and the impact property requirements at -46°C can be fulfilled for this product. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - ...	Open
151	9.0	AI	No	add date	Weld repairs are not acceptable as explicitly required by NORSOK MDS S01 Rev 05 for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 ....	Open
152	3.1	AI	No	add date	Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis for DMV 25.7N is compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
153	4.3	AI	No	add date	DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C (transverse: 45 J avg/35 J single, longitudinal: 65 J avg/50 J single if transverse not possible). The specified pipe dimensions allow for required transverse Charpy ...	Open
154	4.5	AI	No	add date	No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided in the available documentation.	Open
155	3.1	AI	No	add date	DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat, confirming conformity to the requireme...	Open
156	3.1	AI	No	add date	Chemical composition for UNS S32760 matches the requirement table and DMV material composition conforms to this specification with heat analysis and supplier certification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detai...	Open
157	7.0	AI	No	add date	ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx	Open
158	3.2	AI	No	add date	Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...	Open
159	7.0	AI	No	add date	ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: ASTM A 790.docx, NORSOK MDS D51 Rev 06.docx	Open
160	4.4.3	AI	No	add date	Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification digest. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Diges...	Open
161	4.1	AI	No	add date	One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for each heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...	Open
162	4.5	AI	No	add date	No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation or comments.	Open
163	4.4.3	AI	No	add date	Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...	Open
164	4.4.3	AI	No	add date	Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impa...	Open
165	5.2	AI	No	add date	100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 or ISO 10893-10 is feasible for the specified pipe dimensions, and compliance with calibration notch requirements is ensured by adherence to ASTM E213. Source: DMV_STANDARD...	Open
166	5.2	AI	No	add date	NDE per ASTM A790 is confirmed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD (219.1 mm), standard NDE (eddy current, ultrasonic, hydrostatic)...	Open
167	5.2	AI	No	add date	No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor is there confirmation that the required NDE with this acceptance criterion is s...	Open
168	6.0	AI	No	add date	Dimensional tolerances are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790) for the specified pipe size, with no overriding requirements from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV...	Open
169	1.0	AI	No	add date	DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifica...	Open
170	3.2	AI	No	add date	Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...	Open
171	4.2	AI	No	add date	DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...	Open
172	4.4.2	AI	No	add date	Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...	Open
173	4.4.3	AI	No	add date	Ferrite content is determined per ASTM E1245 by default and ASTM E562 on request, both performed in accordance with ISO 17781, fulfilling the requirement for ferrite content determination methods and standard compliance. Source: DMV_STANDARD_BOOK/02 ...	Open
174	4.5	AI	No	add date	Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02...	Open
175	5.2	AI	No	add date	No provided document explicitly confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that such NDE acceptance criteria are standardly performed or feasible for the specified pipe size ...	Open
176	10.0	AI	No	add date	MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...	Open
177	10.1	AI	No	add date	Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified s...	Open
178	10.2	AI	No	add date	ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...	Open
179	10.2	AI	No	add date	EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced throughout the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06....	Open
180	10.2	AI	No	add date	Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive te...	Open
181	1.0	AI	No	add date	DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all relevant chemical, mechanical, manufacturing, and testing requirements. M-650 qualification is confirmed for the required wall thickness. Sourc...	Open
182	1.0	AI	No	add date	No evidence of supplier qualification to both NORSOK M-650 and ISO 17782, nor availability of QTR/MPCR documentation as required by the specification. MST-Tubes is NORSOK M-650 accredited but not ISO 17782 accredited, which does not fully meet the re...	Open
183	3.0	AI	No	add date	MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...	Open
184	3.1	AI	No	add date	Chemical composition for UNS S32760 matches the requirement table and DMV material composition conforms to this specification with heat analysis and supplier certification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detai...	Open
185	3.2	AI	No	add date	Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...	Open
186	4.1	AI	No	add date	One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...	Open
187	4.1	AI	No	add date	Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, directly referencing the table for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detai...	Open
188	4.1	AI	No	add date	Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), corrosion, and microstructure, at specified thickness locations, is fulfilled per ASTM A790 and NORSOK MDS D...	Open
189	4.2	AI	No	add date	Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...	Open
190	4.2	AI	No	add date	DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...	Open
191	4.3	AI	No	add date	DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for required testing directions. Source: 02-04-03 - D...	Open
192	4.4.1	AI	No	add date	Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...	Open
193	4.4.1	AI	No	add date	Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination and matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...	Open
194	4.4.2	AI	No	add date	Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...	Open
195	4.4.2	AI	No	add date	Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...	Open
196	4.4.2	AI	No	add date	Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...	Open
197	4.4.2	AI	No	add date	Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...	Open
198	4.4.2	AI	No	add date	The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...	Open
199	4.4.3	AI	No	add date	Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 ...	Open
200	4.4.3	AI	No	add date	Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...	Open
201	4.5	AI	No	add date	DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...	Open
202	4.5	AI	No	add date	DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...	Open
203	5.1	AI	No	add date	No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...	Open
204	5.2	AI	No	add date	100% ultrasonic testing for longitudinal defects is performed after all mechanical processing, heat treatments, and straightening, in accordance with ASTM E213 and ISO 10893-10, for the specified pipe dimensions. Reference notches are introduced per ...	Open
205	5.2	AI	No	add date	NDE per ASTM A790/ASTM A999 is confirmed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the specified OD (219.1 mm), eddy current testing is not feasible, and ...	Open
206	5.2	AI	No	add date	No explicit confirmation that NDE acceptance criteria require rejection or repair of indications greater than the calibration notch; feasibility for required NDE is not confirmed for the specified dimension at Montbard. Source: DMV_STANDARD_BOOK/02-0...	Open
207	6.0	AI	No	add date	Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) as required, with no deviations or special requests from TechnipFMC indicated in the specification or context. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV...	Open
208	8.0	AI	No	add date	Marking is performed per ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat and DMV lot numbers, ensuring traceability as specified. Source: DMV_STANDARD_BOOK/02-03...	Open
209	1.0	AI	No	add date	Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
210	4.1	AI	No	add date	One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...	Open
211	4.3	AI	No	add date	Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370 and ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc	Open
212	4.4.2	AI	No	add date	Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and the presence and location of intermetallic phases are noted and recorded with micrographs. Source: DMV_STANDARD_BO...	Open
213	4.4.3	AI	No	add date	Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Acceptance criteria require the structure to be basically free from intermetallic precipitates, with iso...	Open
214	5.1	AI	No	add date	No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...	Open
215	6.0	AI	No	add date	Dimensional tolerances are per ASTM A790/A999 as required, with no overriding TechnipFMC specification indicated for the relevant size and product. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK...	Open
216	9.0	AI	No	add date	Weld repairs are explicitly stated as not acceptable under 'Surface finish / Repairs of defects' (§13, §14) for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...	Open
217	10.1	AI	No	add date	MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...	Open
218	9.0	AI	No	add date	Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...	Open
219	10.0	AI	No	add date	MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...	Open
220	10.1	AI	No	add date	MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...	Open
221	10.1	AI	No	add date	Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified s...	Open
222	10.2	AI	No	add date	ISO 9001 certification is provided and documentation is traceable to the products being delivered as required by SIR205 and section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...	Open
223	10.2	AI	No	add date	EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications and plant documentation. Source: DMV_STANDARD_BOOK/02-04-03 - Dig...	Open
224	10.2	AI	No	add date	NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition are stated as included in the EN 10204 3.1 certificate, but the specific steel producer is not provided (only country of origin). All other documentation requ...	Open
225	1.0	AI	No	add date	DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 Rev. 6 as required by the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...	Open
226	1.0	AI	No	add date	No evidence that the supplier is qualified to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of the availability of QTR/MPCR documentation for review by TechnipFMC. One source confirms NORSOK M-650 accreditation but ...	Open
227	3.0	AI	No	add date	MST-Tubes F is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, with manufacturing process qualified to M-650 (or ISO 17782) and meeting NORSOK M-630 MDS D51 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...	Open
228	3.1	AI	No	add date	AOD or equivalent refining is used 100% for DMV 25.7N, and chemical analysis complies with Table 2 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...	Open
229	3.1	AI	No	add date	MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the requested product (WT = 18.26 mm). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...	Open
230	3.2	AI	No	add date	Pipes are solution annealed followed by water quenching per ASTM A790, with furnaces and processes qualified to NORSOK M-650, and free circulation during heat treatment ensured by compliance with these standards. Source: DMV_STANDARD_BOOK/02 - Specif...	Open
231	4.1	AI	No	add date	Test specimen sampling is outlined in Table 3 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx	Open
232	3.1	AI	No	add date	AOD or equivalent refining is used and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
233	4.1	AI	No	add date	There is no evidence that impact, tensile, hardness, corrosion testing, and microstructure examinations are performed for each heat and heat treatment lot as defined in ASTM A790. Testing frequency, lot definition, and full compliance with the requir...	Open
234	4.1	AI	No	add date	Tensile testing per ASTM A790 is confirmed, but there is no evidence of CVN impact testing, required sampling locations, or directions for CVN, microstructure, or corrosion tests as specified in Table 3. Full test sampling requirements are not demons...	Open
235	4.2	AI	No	add date	Tensile testing is performed per lot at room temperature with criteria matching or exceeding Table 4 (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%), and hardness testing is also performed. Compliance with NORSOK MDS D51 and mechanical property requirements...	Open
236	4.2	AI	No	add date	Mechanical property values (tensile strength, yield strength, elongation, hardness) required in Table 4 are not confirmed or addressed for DMV 25.7N in the provided sources. No evidence that the requirement is fulfilled for the specified grade and pr...	Open
237	4.3	AI	No	add date	Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, meeting the minimum wall thickness requirements for both ASTM and ISO standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Dest...	Open
238	4.3	AI	No	add date	Impact testing at -466C with specified absorbed energy values is fulfilled for pipe with 18.26mm wall thickness; both longitudinal and transverse specimens are feasible and requirements are met. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for h...	Open
239	4.4.1	AI	No	add date	No information is provided regarding metallographic preparation, ISO 17781, or the specified etching procedure for 25 Cr Duplex stainless steels. Grain size examination is only addressed for austenitic materials, not duplex steels. Source: DMV_STANDA...	Open
240	4.4.1	AI	No	add date	No information confirming the use of 20-40% NaOH or KOH solution or other suitable etchants as per ISO 17781 Appendix B for micrographic examination or to reveal ferrite balance and intermetallic phases is provided. Source: DMV_STANDARD_BOOK/12 - Spe...	Open
241	4.4.2	AI	No	add date	The micrographic examination section requires the microstructure to be basically free from intermetallic precipitates, allowing isolated precipitates if not homogeneously distributed and each is below 10 μm, matching the client's requirement exactly....	Open
242	4.4.2	AI	No	add date	No evidence that the presence and location of intermetallic phases are noted and recorded with micrographs at 400x or higher magnification; only grain size measurement is addressed and no relevant engineering comments are provided. Source: DMV_STANDA...	Open
243	4.4.2	AI	No	add date	Micrographic examination at a minimum of 400x magnification and inclusion of photos are specified, but it is not explicitly stated that a representative micrograph at or near mid-wall thickness is recorded when intermetallic phases are not detected, ...	Open
244	4.4.2	AI	No	add date	No provided documents address the reporting or acceptance criteria for centerline intermetallic stringers, nor do they link acceptance to CVN or corrosion test results in their presence. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in ...	Open
245	4.4.2	AI	No	add date	Referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or allow isolated intermetallic precipitates under certain conditions, which does not meet the stricter client requi...	Open
246	4.4.3	AI	No	add date	No evidence of ferrite content measurement by ASTM E 562, ASTM E 1245, or ISO 17781 is provided; only grain size measurement is discussed or no relevant information is available. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive test...	Open
247	4.4.3	AI	No	add date	No provided document specifies acceptance criteria or results for micrographic examination or metallurgical properties relevant to DMV 25.7N; grain size examination is also stated as not applicable to duplex/super-duplex stainless steels in the refer...	Open
248	4.4.3	AI	No	add date	Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
249	4.5	AI	No	add date	No specific acceptance criteria for metallurgical properties are provided; only a heading is present without detailed requirements or values. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/0...	Open
250	4.5	AI	No	add date	Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria: no pitting at 20X magnification and weight loss < 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...	Open
251	5.1	AI	No	add date	No provided documents contain information on the qualification or certification of NDE personnel to ISO 9712 level II or III, or their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, ...	Open
252	5.2	AI	No	add date	No evidence provided that 100% ultrasonic testing for longitudinal defects will be performed in accordance with ASTM E213 or ISO 10893-10, or that reference notches and test timing requirements are met. Source: DMV_STANDARD_BOOK/12 - Special Testing/...	Open
253	5.2	AI	No	add date	Dye penetrant testing is available for tube ends and bevels on request, matching the client inquiry which does not require full-length testing. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-05 - Dye penetrant te...	Open
254	5.2	AI	No	add date	No provided document confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor do they specify acceptance criteria or relevant NDE procedures for the requested dimension at Montbard. NDE...	Open
255	6.0	AI	No	add date	Dimensional tolerances for OD, WT, and ovality for hot and cold finished products are confirmed as per the applicable ASTM standards (including ASTM A790/A999) for the relevant dimensions, with no deviations or TechnipFMC overrides indicated. Source:...	Open
256	7.0	AI	No	add date	Pipes are required to be pickled or bright annealed (ASTM A790) and white pickled or bright annealed (NORSOK MDS S01), directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790, NORSOK MDS S01.	Open
257	9.0	AI	No	add date	Weld repairs are not acceptable as explicitly required by NORSOK MDS S01 Rev 05 for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 ....	Open
258	10.0	AI	No	add date	No evidence of an appropriate quality-assurance system (such as ISO 9001 certification by a competent EEA body) is provided for the Montbard plant or manufacturer; referenced documents do not contain certification details or confirmation of complianc...	Open
259	4.4.3	AI	No	add date	Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...	Open
260	10.1	AI	No	add date	No evidence that the material manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body as required by the specification or that required documentation is submitted to TechnipFMC for approval. Source: DMV_STANDARD_BOOK/1...	Open
261	10.1	AI	No	add date	Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...	Open
262	10.2	AI	No	add date	No evidence that documentation traceable to the products and to be transmitted to TechnipFMC (SIR205) will be provided as required by the specification section 10.0. Types of certificates and inspection are listed, but explicit fulfillment of the req...	Open
263	10.2	AI	No	add date	Material certificate is issued according to EN 10204 Type 3.1 and validated by Quality Control for mill inspection. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-03 - Certifica...	Open
264	10.2	AI	No	add date	None of the provided documents contain the required documentation or certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing paramete...	Open
265	1.0	AI	No	add date	DMV 25.7N seamless pipes are manufactured and tested in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with all relevant mechanical, chemical, corrosion, and qualification requirements met, including M-650 qualification up to the req...	Open
266	1.0	AI	No	add date	Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782, as required. No confirmation of QTR/MPCR availability for review is provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...	Open
267	3.0	AI	No	add date	MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...	Open
268	3.1	AI	No	add date	AOD or equivalent refining is standard for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
269	3.1	AI	No	add date	DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 06, including PREN ≥ 40 and all specified element limits and ranges. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 ...	Open
270	3.2	AI	No	add date	Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...	Open
271	4.1	AI	No	add date	One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...	Open
272	4.1	AI	No	add date	Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...	Open
273	4.1	AI	No	add date	Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure, is performed per NORSOK MDS D51/ASTM A790 requirements. For the ordered pipe d...	Open
274	4.2	AI	No	add date	Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...	Open
275	4.2	AI	No	add date	DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...	Open
276	4.3	AI	No	add date	Charpy V-notch testing in accordance with ASTM A370 and ISO 148-1 is feasible for the specified pipe dimensions and can be performed as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03...	Open
277	4.3	AI	No	add date	DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible), for thickness ≥6 mm. The specified p...	Open
278	4.4.1	AI	No	add date	Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...	Open
279	4.4.1	AI	No	add date	Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...	Open
280	4.4.2	AI	No	add date	Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...	Open
281	4.4.2	AI	No	add date	Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...	Open
282	4.4.2	AI	No	add date	Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...	Open
283	4.4.2	AI	No	add date	Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...	Open
284	4.4.2	AI	No	add date	The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates, which does not meet the stricter client requirement of no intermetallics or...	Open
285	4.4.3	AI	No	add date	Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...	Open
286	4.4.3	AI	No	add date	Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...	Open
287	4.4.3	AI	No	add date	Ferrite content requirement of 35% to 60% is fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
288	4.5	AI	No	add date	No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx	Open
289	4.5	AI	No	add date	DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...	Open
290	4.5	AI	No	add date	DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...	Open
291	5.1	AI	No	add date	No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...	Open
292	5.2	AI	No	add date	100% ultrasonic testing for longitudinal defects is performed in accordance with ASTM E213 and ISO 10893-10 after all processing steps, and the dimensional range is covered. Reference notches and calibration are in line with ASTM E213 requirements. S...	Open
293	5.2	AI	No	add date	NDE acceptance criteria per ASTM A790 are partially met via 100% hydrostatic or NDE (EC or UT) testing, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the reque...	Open
294	5.2	AI	No	add date	None of the relevant documents explicitly confirm that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor do they confirm the required NDE acceptance criteria or feasibility fo...	Open
295	6.0	AI	No	add date	Dimensional tolerances are per ASTM A790 and referenced ASTM A999, as required, with no overriding specifications from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according ...	Open
296	8.0	AI	No	add date	Marking is performed according to ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring compliance with the requirement for traceab...	Open
297	9.0	AI	No	add date	Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORS...	Open
298	10.0	AI	No	add date	MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...	Open
299	10.1	AI	No	add date	MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...	Open
300	10.1	AI	No	add date	MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV25.7N, and the EN 10204 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...	Open
301	10.2	AI	No	add date	ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...	Open
302	4.4.3	AI	No	add date	Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
303	10.2	AI	No	add date	EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - ...	Open
304	10.2	AI	No	add date	EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the actual steel producer's name. No specific do...	Open
305	1.0	AI	No	add date	DMV 25.7N seamless pipe is specified as compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, with M-650 qualification confirmed for the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...	Open
306	1.0	AI	No	add date	Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence provided for QTR/MPCR availability or full compliance with both standards as required by the specification. Source: DMV_STANDARD_...	Open
307	3.0	AI	No	add date	MST-Tubes is NORSOK M-650 accredited for DMV 25.7N, with manufacturing process qualified to M-650 (or ISO 17782), and compliance with NORSOK M-630 MDS D51 Rev. 6 is confirmed. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...	Open
308	3.1	AI	No	add date	Chemical composition for S32760 matches Table 2 requirements and is confirmed to conform per heat analysis for DMV material. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ...	Open
309	3.2	AI	No	add date	Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...	Open
310	4.1	AI	No	add date	One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...	Open
311	4.1	AI	No	add date	Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...	Open
312	4.1	AI	No	add date	Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests are performed at the spec...	Open
313	4.2	AI	No	add date	Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...	Open
314	4.2	AI	No	add date	DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...	Open
315	4.3	AI	No	add date	Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, as the wall thickness exceeds the minimum required by the standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 ...	Open
316	4.3	AI	No	add date	DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact test requirements at -46°C, with minimum absorbed energy values for both transverse and longitudinal directions. The specified pipe wall thickness (18.26mm) allows for the required impact testing a...	Open
317	4.5	AI	No	add date	No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 will be performed or is referenced. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx	Open
318	4.4.1	AI	No	add date	Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...	Open
319	4.4.1	AI	No	add date	Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is specified and fulfills the requirement for suitable etchant(s) as listed in ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Spe...	Open
320	4.4.2	AI	No	add date	Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...	Open
321	4.4.2	AI	No	add date	Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...	Open
322	4.4.2	AI	No	add date	Micrographs at a minimum magnification of 400x are included, reported at actual magnification with a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...	Open
323	4.4.2	AI	No	add date	Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...	Open
324	4.4.2	AI	No	add date	The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates, which does not meet the stricter client requirement of not permitting any i...	Open
325	4.4.3	AI	No	add date	Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...	Open
326	4.4.3	AI	No	add date	Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...	Open
327	4.4.3	AI	No	add date	Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...	Open
328	4.5	AI	No	add date	DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, as well as manufacturing, heat treatment, and qualification requirements. Source: DMV_STAN...	Open
329	4.5	AI	No	add date	Corrosion test per ISO 17781 (G48 Method A @ 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², both of which are met. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...	Open
330	5.1	AI	No	add date	No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...	Open
331	5.2	AI	No	add date	100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 or ISO 10893-10 is feasible and standards-compliant for the specified pipe dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Sourc...	Open
332	7.0	AI	No	add date	ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: ASTM A 790.docx, NORSOK MDS D51 Rev 06.docx	Open
333	5.2	AI	No	add date	NDE acceptance criteria per ASTM A790, NORSOK M-630 MDS D51 Rev 6, and NORSOK M-650/ISO 17782 are not confirmed as fulfilled; available documentation only partially covers NDE per ASTM A790/A999 and does not confirm compliance with NORSOK requirement...	Open
334	5.2	AI	No	add date	No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor is there confirmation that the required NDE is standardly performed or feasible...	Open
335	6.0	AI	No	add date	Dimensional tolerances are specified as per ASTM A790 and ASTM A999, with no alternative tolerances from TechnipFMC stated. Requirement is fulfilled as tolerances follow the applicable ASTM standard unless otherwise specified, which is not the case h...	Open
336	8.0	AI	No	add date	Marking per ASTM A790 includes heat and lot numbers, ensuring full traceability to melt and heat treatment lot; standard marking methods (indelible ink, vibro-etching) at Montbard include these identifiers as required. Source: DMV_STANDARD_BOOK/02-04...	Open
337	9.0	AI	No	add date	Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' in the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...	Open
338	10.0	AI	No	add date	MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...	Open
339	10.1	AI	No	add date	MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...	Open
340	10.1	AI	No	add date	MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the specified wall thickness, and the QTR number is included as per M-650 qualification, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/M...	Open
341	10.2	AI	No	add date	ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, are provided and meet the requirement for transmission and traceability to TechnipFMC as per S...	Open
342	10.2	AI	No	add date	EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification summary. Source: DMV_STANDARD_BOOK...	Open
343	10.2	AI	No	add date	Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution annealing temperature/hold...	Open
344	1.0	AI	No	add date	DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified for the required wall thickness. Source: DMV_S...	Open
345	1.0	AI	No	add date	Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability. Requirement for NORSOK M-650/ISO 17782 qualification and documentation availability is not fully m...	Open
346	3.0	AI	No	add date	MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...	Open
347	3.1	AI	No	add date	AOD or equivalent refining is required and standard for production, and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
348	3.1	AI	No	add date	DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat, confirming conformity to the required ...	Open
349	3.2	AI	No	add date	Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...	Open
350	4.1	AI	No	add date	One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...	Open
351	4.1	AI	No	add date	Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...	Open
352	4.1	AI	No	add date	Test sampling for seamless pipes (DMV 25.7N) per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed as required, w...	Open
353	4.2	AI	No	add date	Tensile testing is performed per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 as required by NORSOK MDS D51 and ASTM A790 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...	Open
354	4.2	AI	No	add date	DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 06 and ASTM A790 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...	Open
355	4.3	AI	No	add date	Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...	Open
356	4.3	AI	No	add date	DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energy values for both transverse and longitudinal directions, and the specified pipe dimensions allow for required testing directions and valu...	Open
357	4.4.1	AI	No	add date	Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...	Open
358	4.4.1	AI	No	add date	Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...	Open
359	4.4.2	AI	No	add date	Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...	Open
360	4.5	AI	No	add date	No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx	Open
361	4.4.2	AI	No	add date	Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...	Open
362	4.4.2	AI	No	add date	Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...	Open
363	4.4.2	AI	No	add date	Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...	Open
364	4.4.2	AI	No	add date	The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates, which does not meet the stricter client requirement of not permitting any i...	Open
365	4.4.3	AI	No	add date	Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...	Open
366	4.4.3	AI	No	add date	Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...	Open
367	4.4.3	AI	No	add date	Ferrite content is specified as 35% to 60% and DMV 25.7N complies per ISO 17781/ASTM E1245 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...	Open
368	4.5	AI	No	add date	DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified per NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specifications...	Open
369	4.5	AI	No	add date	DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...	Open
370	5.1	AI	No	add date	No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source: DMV_STAN...	Open
371	5.2	AI	No	add date	100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...	Open
372	5.2	AI	No	add date	NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/650 are not fully addressed; only general hydrostatic or NDE (EC/UT) per ASTM A999 is confirmed, with no explicit evidence for NORSOK-specific requirements. For the requested OD, eddy cur...	Open
373	5.2	AI	No	add date	No provided document explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor that this NDE acceptance criterion is standardly performed or feasible for the specified pipe di...	Open
374	6.0	AI	No	add date	Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the requested pipe, with no evidence of a different requirement from TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - ...	Open
375	8.0	AI	No	add date	Marking per ASTM A790 and plant practices includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-...	Open
376	9.0	AI	No	add date	Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...	Open
377	10.0	AI	No	add date	MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA and specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...	Open
378	10.1	AI	No	add date	MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...	Open
379	10.1	AI	No	add date	MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, and the QTR number is included in the certificate, fulfilling the requirement for supplier qualification documentation per SIR131. Source: DMV_STANDARD_BOOK/0...	Open
380	10.2	AI	No	add date	ISO 9001 certification is provided and documentation is traceable to delivered products, fulfilling SIR205 and specification requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORS...	Open
381	10.2	AI	No	add date	EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 qualification summary. Source:...	Open
382	10.2	AI	No	add date	Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and...	Open
383	1.0	AI	No	add date	DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all standard and supplementary requirements, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/...	Open
384	3.0	AI	No	add date	MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...	Open
385	4.1	AI	No	add date	Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...	Open
386	4.3	AI	No	add date	DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C (transverse: 45/35 J, longitudinal: 65/50 J) for thickness >6mm, and the specified pipe dimensions allow for required testing directions and specimen sizes. Source: D...	Open
387	4.4.2	AI	No	add date	Micrographic examination is performed at a minimum magnification of 400x with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected, fulfilling the requirem...	Open
388	4.4.3	AI	No	add date	Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
389	1.0	AI	No	add date	Supplier is M-650 accredited for DMV25.7N but not accredited to ISO 17782 as required; full qualification per NORSOK M-650/ISO 17782 is not demonstrated. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
390	3.0	AI	No	add date	MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...	Open
391	3.1	AI	No	add date	AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx	Open
392	3.1	AI	No	add date	DMV 25.7N (UNS S32760) complies with the chemical composition limits and PREN ≥ 40 as specified in Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 6 requirements for S32760. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D...	Open
393	3.2	AI	No	add date	Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification will state heat treatment condition as per ASTM A790. Pipes are processed to ensure ...	Open
394	4.1	AI	No	add date	One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...	Open
395	4.1	AI	No	add date	Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...	Open
396	4.1	AI	No	add date	Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, are fulfilled for DMV 25.7N. The...	Open
397	4.2	AI	No	add date	Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with material meeting the tensile and maximum hardness properties of Table 4 as required by NORSOK MDS D51. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...	Open
398	4.2	AI	No	add date	DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...	Open
399	4.3	AI	No	add date	The pipe wall thickness exceeds the minimum required for Charpy V-notch testing, and the plant confirms feasibility for Charpy testing per ASTM A370 or ISO 148-1. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc	Open
400	4.3	AI	No	add date	DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, with minimum absorbed energy values for both transverse and longitudinal specimens, and the specified pipe dimensions allow for required testing directions. Source:...	Open
401	4.4.1	AI	No	add date	Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...	Open
402	4.4.1	AI	No	add date	Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...	Open
403	4.4.2	AI	No	add date	Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...	Open
404	1.0	AI	No	add date	Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782 as required; no evidence provided for availability of QTR/MPCR for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
405	4.4.2	AI	No	add date	Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported as required. Source: DMV_STANDARD_BOOK/02 - Spec...	Open
406	4.4.2	AI	No	add date	Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...	Open
407	4.4.2	AI	No	add date	Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...	Open
408	4.4.2	AI	No	add date	The digest allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size. No other relevant information addresses the re...	Open
409	4.4.3	AI	No	add date	Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...	Open
410	4.4.3	AI	No	add date	Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...	Open
411	4.4.3	AI	No	add date	Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...	Open
412	4.5	AI	No	add date	No explicit evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or documented for the requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx	Open
413	4.5	AI	No	add date	DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, with M-650 qualification for the specified grade and wall thickness. Source: DMV_STANDARD_...	Open
414	4.5	AI	No	add date	DMV 25.7N is tested per ISO 17781 (G48 Method A @ 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and complies with these requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...	Open
415	5.1	AI	No	add date	No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...	Open
416	5.2	AI	No	add date	100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within capability range. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02...	Open
417	5.2	AI	No	add date	NDE per ASTM A790 is partially addressed with hydrostatic or NDE (EC or UT) per ASTM A999, but there is no explicit evidence of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements. Eddy current testing is no...	Open
418	5.2	AI	No	add date	No provided document explicitly states that any indication greater than the calibration notch is considered a defect requiring rejection or repair; NDE acceptance criteria and process capability do not fulfill the requirement for the specified pipe s...	Open
419	6.0	AI	No	add date	Dimensional tolerances are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790) for the specified pipe size, with no deviations or special requirements from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General informatio...	Open
420	7.0	AI	No	add date	ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx	Open
421	8.0	AI	No	add date	Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...	Open
422	9.0	AI	No	add date	NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...	Open
423	10.0	AI	No	add date	MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...	Open
424	10.1	AI	No	add date	MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...	Open
425	10.1	AI	No	add date	MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV25.7N, and the EN 10204 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number for the specified size and product form. Source: DMV_ST...	Open
426	10.2	AI	No	add date	MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability information, fulfilling the requirement for documentation traceable to delivered products and transmission to TechnipFMC. Source: DMV_STANDARD_BOOK/02 - Spe...	Open
427	10.2	AI	No	add date	EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications and plant documentation. Source: DMV_STANDARD_BOOK/02-04-03 - Dig...	Open
428	10.2	AI	No	add date	Most documentation and certification requirements are stated as included in the EN 10204 type 3.1 certificate, except the steel producer of the starting material, which is not provided (only country of origin is given). No specific evidence is provid...	Open
429	1.0	AI	No	add date	DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...	Open
430	3.0	AI	No	add date	MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...	Open
431	3.1	AI	No	add date	AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
432	3.1	AI	No	add date	DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
433	3.2	AI	No	add date	Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...	Open
434	4.1	AI	No	add date	One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...	Open
435	4.1	AI	No	add date	Tensile test specimens are sampled as per Table 3 of ASTM A790, with frequency and method matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...	Open
436	4.1	AI	No	add date	Test sampling for seamless pipes, including tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, is fulfilled for DMV 25.7...	Open
437	4.2	AI	No	add date	Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...	Open
438	4.2	AI	No	add date	DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: minimum tensile strength 750 MPa, yield strength 550 MPa, elongation 25%, and maximum hardness 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...	Open
439	4.3	AI	No	add date	Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370 and ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03...	Open
440	4.3	AI	No	add date	DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal. The specified pipe dimensions allo...	Open
441	4.4.1	AI	No	add date	Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed according to ISO 17781 with 20-40% NaOH or KOH solution after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...	Open
442	4.4.1	AI	No	add date	Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...	Open
443	4.4.2	AI	No	add date	Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...	Open
444	4.4.2	AI	No	add date	Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases. Source: DMV_STANDARD_BOOK/02...	Open
445	4.4.2	AI	No	add date	Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...	Open
446	4.4.2	AI	No	add date	Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...	Open
447	4.4.2	AI	No	add date	The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement does not permit any intermetallic phases or precipitates if CVN testing cannot be completed, so the requirement is not fully fulfilled. Source: DMV_S...	Open
448	4.4.3	AI	No	add date	Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...	Open
449	4.4.3	AI	No	add date	Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...	Open
450	4.4.3	AI	No	add date	Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...	Open
451	4.5	AI	No	add date	No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or confirmed in the referenced documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx	Open
452	4.5	AI	No	add date	All metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, microstructure, PRE, solution annealing, and ferrite content, are fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...	Open
453	4.5	AI	No	add date	Corrosion test per ISO 17781 (G48 Method A @ 50°C, 24h) is performed for DMV 25.7N, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and DMV 25.7N complies with these requirements. Source: DMV_STANDARD_BOOK/02 -...	Open
454	5.1	AI	No	add date	No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...	Open
455	5.2	AI	No	add date	100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...	Open
456	5.2	AI	No	add date	NDE per NORSOK M-630 MDS D51/ASTM A790 is not confirmed; only ASTM A790/A999 NDE is detailed, destructive tests are described but not NDE, standard NDE (ultrasonic, eddy current) is not available or only at extra cost for the required OD, and full-le...	Open
457	5.2	AI	No	add date	No provided documentation confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor is there confirmation that such NDE acceptance criteria are standardly performed or f...	Open
458	6.0	AI	No	add date	Dimensional tolerances for OD, WT, and ovality are per ASTM A790 and referenced ASTM A999, with no deviations specified in the customer requirements, fulfilling the requirement for ASTM standard tolerances unless otherwise stated. Source: DMV_STANDAR...	Open
459	7.0	AI	No	add date	ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx	Open
460	8.0	AI	No	add date	Marking per ASTM A790 and plant marking methods ensure mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDA...	Open
461	9.0	AI	No	add date	NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
462	10.0	AI	No	add date	MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...	Open
463	10.1	AI	No	add date	MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...	Open
464	10.1	AI	No	add date	MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV25.7N up to 31.75 mm WT, covering the required 18.26 mm, and the EN 10204 3.1 certificate will include the NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, demonstr...	Open
465	10.2	AI	No	add date	ISO 9001 certification is provided and documentation is traceable to the products being delivered as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...	Open
466	10.2	AI	No	add date	EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference. Source: D...	Open
467	10.2	AI	No	add date	No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all required metallurgic...	Open
468	1.0	AI	No	add date	DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification digest and the listing of 'A790 NORSOK' under customer specifications. Manufacturing is M-650 qualified for th...	Open
469	3.1	AI	No	add date	AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev...	Open
470	4.1	AI	No	add date	Test sampling for seamless pipes per ASTM A790 and NORSOK MDS D51 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations. Fo...	Open
471	4.4.1	AI	No	add date	Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...	Open
472	4.4.2	AI	No	add date	Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...	Open
473	4.5	AI	No	add date	No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is fulfilled or documented for the requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx	Open
474	5.2	AI	No	add date	Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, performed after all mechanical processing, meeting the requirement for 100% longitudinal defect detection. Source: DMV_STANDARD_BOOK/12 -...	Open
475	7.0	AI	No	add date	ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx	Open
476	1.0	AI	No	add date	Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782 as required; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
477	3.0	AI	No	add date	MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...	Open
478	3.1	AI	No	add date	AOD or equivalent refining is used 100% for DMV 25.7N, and chemical composition complies with Table 2 of ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx	Open
479	3.1	AI	No	add date	DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Heat analysis is performed per heat and matches the specified limits for all elements listed in the...	Open
480	3.2	AI	No	add date	Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - S...	Open
481	4.1	AI	No	add date	One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...	Open
482	4.1	AI	No	add date	Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...	Open
483	4.1	AI	No	add date	Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests, with specified locations and directions, is fulfilled for DMV 25.7N per ...	Open
484	4.2	AI	No	add date	Tensile testing is performed at room temperature per required standards, with mechanical properties and hardness requirements matching Table 4; compliance with ASTM A370 or ISO 6892-1 and NORSOK MDS D51 is confirmed. Source: DMV_STANDARD_BOOK/02 - Sp...	Open
485	4.2	AI	No	add date	DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: yield strength ≥ 550 MPa, tensile strength ≥ 750 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW, fulfilling all specified mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...	Open
486	4.3	AI	No	add date	Charpy V-notch testing is feasible and fulfills the requirement as the pipe wall thickness exceeds the minimum required by ASTM and ISO standards for such testing. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc	Open
487	4.3	AI	No	add date	DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C (transverse: 45 J avg/35 J single, longitudinal: 65 J avg/50 J single) for thickness >6 mm. The specified pipe dimensions allow for required testing directions and s...	Open
488	4.4.1	AI	No	add date	Micrographic examination and ferrite check are performed as per ISO 17781, but the exact etchant solution and procedure required for intermetallic phase detection and ferrite balance after final polishing are not fully specified as per the client's r...	Open
489	4.4.1	AI	No	add date	Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is explicitly required for micrographic examination as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...	Open
490	4.4.2	AI	No	add date	Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...	Open
491	4.4.2	AI	No	add date	Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...	Open
492	4.4.2	AI	No	add date	Micrographs at a minimum magnification of 400x are included, reported at actual magnification with a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...	Open
493	4.4.2	AI	No	add date	Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...	Open
494	4.4.2	AI	No	add date	The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...	Open
495	4.4.3	AI	No	add date	Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...	Open
496	4.4.3	AI	No	add date	Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corro...	Open
497	4.4.3	AI	No	add date	Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...	Open
498	4.5	AI	No	add date	ASTM G48 Method 'A' corrosion testing at 50°C for 24h in accordance with ISO 17781 is not explicitly mentioned or confirmed; compliance cannot be validated based on the available information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Mon...	Open
499	4.5	AI	No	add date	DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, chemical composition, ferrite content, and corrosion/impact requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...	Open
500	4.5	AI	No	add date	DMV 25.7N is tested per ISO 17781 (G48 Method A @ 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...	Open

1

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or confirmed. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

2

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

3

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

5

4.4.1

AI

No

add date

No evidence confirms metallographic preparation and examination are performed according to ISO 17781 with the specified etchant solution for 25 Cr Duplex stainless steels as required. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_S...

Open

6

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

7

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

8

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions, is fulfilled for DMV 25.7N. The or...

Open

9

10.2

AI

No

add date

Most documentation and certification requirements are addressed, including NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but the actual steel producer's name is not provided (only country of origin), and...

Open

10

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

12

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

13

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination per ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels; grain size examination is only discussed for austenitic materials and is not applicab...

Open

14

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

15

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; full qualification to NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR is not confirmed. Source: DMV_STANDARD_BOOK/02...

Open

16

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchants as per ISO 17781 Appendix B for micrographic examination; requirement not addressed for ferrite balance and intermetallic phases. Source: DMV_STANDARD_BOOK/12 - Special Test...

Open

17

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfills the requirement as the pipe wall thickness exceeds the minimum required by ASTM and ISO standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-0...

Open

18

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N (UNS S32760) up to 31.75 mm WT, and the requirement is for 18.26 mm WT. The manufacturing process is qualified to NORSOK M-650 or ISO 17782, with qualification testing per NORSOK M-630 MDS D51 rev. 6...

Open

19

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

20

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energy values for both transverse and longitudinal directions, and the specified pipe dimensions allow for required testing directions and spec...

Open

21

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

22

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/650 are not confirmed as fulfilled. For OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at extra cost. Dye penetrant testing is limi...

Open

23

4.4.2

AI

No

add date

The microstructure must be basically free from intermetallic precipitates, but isolated precipitates are allowed if not distributed over the whole specimen and if the dimension of each precipitate is below 10 μm, matching the requirement exactly. Sou...

Open

24

4.5

AI

No

add date

DMV 25.7N meets ISO 17781: G48 Method A at 50°C for 24h, with no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

25

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

26

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as per Table 2 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

27

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

28

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

29

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair; NDE acceptance criteria and required testing are not demonstrably fulfilled for the specified produc...

Open

30

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

31

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

32

6.0

AI

No

add date

Dimensional tolerances are specified as per the applicable ASTM standard (ASTM A790 referencing ASTM A999) for the relevant dimensions, with no overriding requirements from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.d...

Open

33

4.4.2

AI

No

add date

No information or documentation is provided regarding the recording and micrographic documentation (at 400x minimum) of intermetallic phases; the requirement is not addressed or fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destru...

Open

34

10.0

AI

No

add date

No evidence of an ISO 9001 or equivalent quality-assurance system certified by a competent EEA body is provided for the Montbard plant or manufacturer. No certification details or confirmation are present in the referenced documents or excerpts. Sour...

Open

35

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

36

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, exceeding the minimum wall thickness required for testing. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

37

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

38

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

39

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: ASTM A 790, NORSOK MDS D51 Rev 06.

Open

40

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at actual magnification with a scale bar if intermetallic phases are not detected; reporting requirements are not directly addressed or confirmed in t...

Open

41

10.1

AI

No

add date

No evidence that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification or that documentation will be submitted to TechnipFMC for approval. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 ...

Open

42

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, with test frequency 1/lot matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

43

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH is used to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

44

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

45

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot, in accordance with ASTM A790 and standard practice at Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, ...

Open

46

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

47

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria based on CVN and corrosion...

Open

48

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests, with specified locations and directions, is fulfilled for DMV 25.7N per ...

Open

49

9.0

AI

No

add date

Weld repairs are explicitly stated as not acceptable under 'Surface finish / Repairs of defects' (§13, §14) for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 -...

Open

50

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size. Requirement not fully fulfilled. Source: DMV_S...

Open

51

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

52

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA and specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

53

4.4.2

AI

No

add date

No provided documents address the presence, reporting, or acceptance criteria for centerline intermetallic stringers, nor do they link acceptance to CVN and corrosion test results in such cases. Requirement not fulfilled based on available informatio...

Open

54

10.1

AI

No

add date

Certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, demonstrating qualification for the size and product...

Open

55

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or specified. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

56

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

57

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

58

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

59

4.4.2

AI

No

add date

Referenced specifications allow isolated intermetallic precipitates below 10µm and do not enforce a complete prohibition of intermetallic phases/precipitates if CVN testing cannot be completed, which is stricter in the client requirement. No document...

Open

60

10.2

AI

No

add date

No evidence that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC as specified in the requirement. Certification and inspection documents are referenced, but explicit fulfillment is not demonstrated for...

Open

61

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

62

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

63

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

64

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Structure must be basically free from intermetallic precipitates, with isolated precipitates allowed if ...

Open

65

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

66

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV 25.7N up to WT = 31.75 mm, covering the requested size, and the EN 10204 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number. Sour...

Open

67

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Micrographic Examination/12-03-03 - Grain Size Ex...

Open

68

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

69

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for both test orientations. Source: DMV_ST...

Open

70

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to the delivered products, fulfilling the documentation and traceability requirement as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

71

4.4.3

AI

No

add date

No acceptance criteria for micrographic examination are provided or applicable for DMV 25.7N (super-duplex stainless steel); grain size examination is not required for this material and is not addressed in the referenced standards or digests. Source:...

Open

72

10.2

AI

No

add date

Material certificate is issued according to EN 10204 Type 3.1 and validated by Quality Control for mill inspection; compliance with ASTM A790 and NORSOK M-630 information is not explicitly confirmed but certificate type and process are compliant. Sou...

Open

73

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions. For the ord...

Open

74

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

75

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

76

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

77

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-...

Open

78

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and confirmed for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D41 Re...

Open

79

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1 at room temperature, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

80

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK/0...

Open

81

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

82

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination in accordance with the requirement. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

83

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive te...

Open

84

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

85

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

86

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

87

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are manufactured and tested in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, meeting all relevant mechanical, chemical, and testing standards. Source: DMV_STAND...

Open

88

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are provided in the referenced documents or section; only headings or general references are present without detailed requirements or limits. Source: DMV_STANDARD_BOOK/02-03-01 - Digest AST...

Open

89

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

90

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

91

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled. Source: DMV_STANDARD_BOOK/12-02-01 - Non ...

Open

92

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and the presence and location of intermetallic phases are noted and recorded with micrographs. Source: DMV_STANDARD_BO...

Open

93

1.0

AI

No

add date

No evidence that the supplier is qualified to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of the availability of the full Qualification Test Record/MPCR for review as required by the specification. ISO 17782 accre...

Open

94

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria: no pitting at 20X magnification and weight loss < 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

95

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions (18.26mm WT, 219.1mm OD). Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

96

4.4.2

AI

No

add date

Micrographs at a minimum magnification of 400x are included, with actual magnification and scale bar, fulfilling the requirement for representative micrographs at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDA...

Open

97

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects is performed in accordance with ASTM E213 and ISO 10893-10 after all mechanical processing, heat treatments, and straightening, and the dimensional range of the requested pipe is supported. Source: DMV...

Open

98

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

99

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 and meets NORSOK MDS D51 Rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

100

5.1

AI

No

add date

No provided documents mention the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDARD_B...

Open

101

10.2

AI

No

add date

No provided documents include NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or results of required metallurgical and non-destructive testing as specified. Only gen...

Open

102

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

103

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not fully addressed; only ASTM A790/ASTM A999 requirements are confirmed. For the specified OD, standard NDE methods at Montbard are either not feasible or only ava...

Open

104

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_ST...

Open

105

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N complies with the required chemical analysis. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NOR...

Open

106

5.2

AI

No

add date

No provided document explicitly states that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor confirms that the required NDE will be performed as standard for the specified pi...

Open

107

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

108

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the requested WT of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest ...

Open

109

5.2

AI

No

add date

Pipe dimensions are within ultrasonic testing capability, but there is no confirmation that testing is performed after all processing or that calibration notches meet ASTM E213 Figure 3 requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

110

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

111

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and referenced ASTM A999, as required, with no overriding specifications indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01...

Open

112

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

113

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, manufacturing process is qualified to NORSOK M-650, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compliance with th...

Open

114

5.2

AI

No

add date

100% qualitative anti-mixing PMI checks are standard at Montbard, with quantitative PMI and procedures available if required, meeting general NDE acceptance criteria for PMI. Source: DMV_STANDARD_BOOK/12-06-06 - Positive Material Identification (PMI)...

Open

115

1.0

AI

No

add date

DMV 25.7N is a 25 Cr Duplex stainless steel seamless pipe fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all referenced mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thicknes...

Open

116

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

117

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with required etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requirement fo...

Open

118

4.1

AI

No

add date

Tensile and hardness tests are performed, but there is no evidence that impact, corrosion, and microstructure examinations are carried out for each heat and heat treatment lot as required by ASTM A790. No explicit confirmation of all required tests p...

Open

119

8.0

AI

No

add date

Marking per ASTM A790 and plant marking methods include heat number and lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02...

Open

120

8.0

AI

No

add date

Marking per ASTM A790 includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Marking methods (indelible ink, vibro-etching) are standard and applied as specified. Source: DMV_STANDARD_BOOK/02-04-03 - Diges...

Open

121

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

122

4.1

AI

No

add date

None of the provided documents outline the test specimens sampling as required in Table 3 or reproduce its details; only a reference to Table 3 is made without specifying the sampling procedure or content of the table itself. Source: DMV_STANDARD_BOO...

Open

123

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor is there confirmation that the required NDE is standardly performed or feasible for the sp...

Open

124

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable' for seamless pipes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

125

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

126

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

127

4.1

AI

No

add date

Test sampling requirements for test directions, CVN impact testing, and thickness locations per Table 3 are not fully addressed; test direction for tensile and inclusion of CVN impact tests are not specified in the provided documents. Source: DMV_STA...

Open

128

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed as per the applicable ASTM standards (including ASTM A 790 with A 999) for the requested dimensions, with no overriding TechnipFMC part report or drawing specified. Source: DMV_STANDARD_BOO...

Open

129

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: ASTM A 790, NORSOK MDS D51 Rev 06.

Open

130

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

131

4.5

AI

No

add date

DMV 25.7N complies with all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive, micrographic, ferrite, corrosion, and impact tests, with required tests and acceptance values matched. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

132

4.2

AI

No

add date

Tensile testing is performed per ASTM A370, with results meeting or exceeding Table 4 requirements (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%), and hardness testing is also conducted as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

133

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and NORSOK MDS S01, fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790, NORSOK MDS S01.

Open

134

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence provided for availability of QTR/MPCR for review as required by the specification. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

135

4.4.2

AI

No

add date

The referenced specifications allow isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not meet the stricter requirement that intermetallic phases and/or precipitates are not permitted at all if CVN ...

Open

136

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification listing and digest, including all mechanical, chemical, and testing requirements. Manufacturing is M-650 qualified for the ...

Open

137

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

138

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, meeting the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest...

Open

139

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required for DMV 25.7N are not explicitly confirmed in the provided documentation; referenced values are either missing or pertain to a different grade (TP316/316L). ...

Open

140

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13 - Marking/13-02 - Standard marking feasibility/13-02-01 - Standard marking feasibility - Montbard plant/13...

Open

141

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

142

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782, as required. No evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

143

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

144

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demonst...

Open

145

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

146

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, meeting the minimum wall thickness requirements for both ASTM and ISO standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Dest...

Open

147

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

148

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

149

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 or ISO 10893-10 is feasible and standards-compliant for the specified pipe dimensions; calibration notches are expected to follow ASTM E213 as the standard is accepted. Sou...

Open

150

4.3

AI

No

add date

The pipe dimensions allow for transverse Charpy specimens, and the impact property requirements at -46°C can be fulfilled for this product. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - ...

Open

151

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS S01 Rev 05 for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 ....

Open

152

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis for DMV 25.7N is compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

153

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C (transverse: 45 J avg/35 J single, longitudinal: 65 J avg/50 J single if transverse not possible). The specified pipe dimensions allow for required transverse Charpy ...

Open

154

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided in the available documentation.

Open

155

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat, confirming conformity to the requireme...

Open

156

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the requirement table and DMV material composition conforms to this specification with heat analysis and supplier certification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detai...

Open

157

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

158

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

159

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: ASTM A 790.docx, NORSOK MDS D51 Rev 06.docx

Open

160

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification digest. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Diges...

Open

161

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for each heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

162

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation or comments.

Open

163

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

164

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impa...

Open

165

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 or ISO 10893-10 is feasible for the specified pipe dimensions, and compliance with calibration notch requirements is ensured by adherence to ASTM E213. Source: DMV_STANDARD...

Open

166

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD (219.1 mm), standard NDE (eddy current, ultrasonic, hydrostatic)...

Open

167

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor is there confirmation that the required NDE with this acceptance criterion is s...

Open

168

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790) for the specified pipe size, with no overriding requirements from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV...

Open

169

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

170

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

171

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

172

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

173

4.4.3

AI

No

add date

Ferrite content is determined per ASTM E1245 by default and ASTM E562 on request, both performed in accordance with ISO 17781, fulfilling the requirement for ferrite content determination methods and standard compliance. Source: DMV_STANDARD_BOOK/02 ...

Open

174

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02...

Open

175

5.2

AI

No

add date

No provided document explicitly confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that such NDE acceptance criteria are standardly performed or feasible for the specified pipe size ...

Open

176

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

177

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified s...

Open

178

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

179

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced throughout the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06....

Open

180

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive te...

Open

181

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all relevant chemical, mechanical, manufacturing, and testing requirements. M-650 qualification is confirmed for the required wall thickness. Sourc...

Open

182

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782, nor availability of QTR/MPCR documentation as required by the specification. MST-Tubes is NORSOK M-650 accredited but not ISO 17782 accredited, which does not fully meet the re...

Open

183

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

184

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the requirement table and DMV material composition conforms to this specification with heat analysis and supplier certification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detai...

Open

185

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

186

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

187

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, directly referencing the table for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detai...

Open

188

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), corrosion, and microstructure, at specified thickness locations, is fulfilled per ASTM A790 and NORSOK MDS D...

Open

189

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

190

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

191

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for required testing directions. Source: 02-04-03 - D...

Open

192

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

193

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination and matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

194

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

195

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

196

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

197

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

198

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

199

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 ...

Open

200

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

201

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

202

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

203

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

204

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects is performed after all mechanical processing, heat treatments, and straightening, in accordance with ASTM E213 and ISO 10893-10, for the specified pipe dimensions. Reference notches are introduced per ...

Open

205

5.2

AI

No

add date

NDE per ASTM A790/ASTM A999 is confirmed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the specified OD (219.1 mm), eddy current testing is not feasible, and ...

Open

206

5.2

AI

No

add date

No explicit confirmation that NDE acceptance criteria require rejection or repair of indications greater than the calibration notch; feasibility for required NDE is not confirmed for the specified dimension at Montbard. Source: DMV_STANDARD_BOOK/02-0...

Open

207

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) as required, with no deviations or special requests from TechnipFMC indicated in the specification or context. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV...

Open

208

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat and DMV lot numbers, ensuring traceability as specified. Source: DMV_STANDARD_BOOK/02-03...

Open

209

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

210

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

211

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370 and ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

212

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and the presence and location of intermetallic phases are noted and recorded with micrographs. Source: DMV_STANDARD_BO...

Open

213

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Acceptance criteria require the structure to be basically free from intermetallic precipitates, with iso...

Open

214

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

215

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding TechnipFMC specification indicated for the relevant size and product. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK...

Open

216

9.0

AI

No

add date

Weld repairs are explicitly stated as not acceptable under 'Surface finish / Repairs of defects' (§13, §14) for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

217

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

218

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

219

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

220

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

221

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified s...

Open

222

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products being delivered as required by SIR205 and section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

223

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications and plant documentation. Source: DMV_STANDARD_BOOK/02-04-03 - Dig...

Open

224

10.2

AI

No

add date

NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition are stated as included in the EN 10204 3.1 certificate, but the specific steel producer is not provided (only country of origin). All other documentation requ...

Open

225

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 Rev. 6 as required by the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

226

1.0

AI

No

add date

No evidence that the supplier is qualified to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of the availability of QTR/MPCR documentation for review by TechnipFMC. One source confirms NORSOK M-650 accreditation but ...

Open

227

3.0

AI

No

add date

MST-Tubes F is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, with manufacturing process qualified to M-650 (or ISO 17782) and meeting NORSOK M-630 MDS D51 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

228

3.1

AI

No

add date

AOD or equivalent refining is used 100% for DMV 25.7N, and chemical analysis complies with Table 2 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

229

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the requested product (WT = 18.26 mm). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

230

3.2

AI

No

add date

Pipes are solution annealed followed by water quenching per ASTM A790, with furnaces and processes qualified to NORSOK M-650, and free circulation during heat treatment ensured by compliance with these standards. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

231

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

232

3.1

AI

No

add date

AOD or equivalent refining is used and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

233

4.1

AI

No

add date

There is no evidence that impact, tensile, hardness, corrosion testing, and microstructure examinations are performed for each heat and heat treatment lot as defined in ASTM A790. Testing frequency, lot definition, and full compliance with the requir...

Open

234

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no evidence of CVN impact testing, required sampling locations, or directions for CVN, microstructure, or corrosion tests as specified in Table 3. Full test sampling requirements are not demons...

Open

235

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature with criteria matching or exceeding Table 4 (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%), and hardness testing is also performed. Compliance with NORSOK MDS D51 and mechanical property requirements...

Open

236

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required in Table 4 are not confirmed or addressed for DMV 25.7N in the provided sources. No evidence that the requirement is fulfilled for the specified grade and pr...

Open

237

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, meeting the minimum wall thickness requirements for both ASTM and ISO standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Dest...

Open

238

4.3

AI

No

add date

Impact testing at -466C with specified absorbed energy values is fulfilled for pipe with 18.26mm wall thickness; both longitudinal and transverse specimens are feasible and requirements are met. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for h...

Open

239

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation, ISO 17781, or the specified etching procedure for 25 Cr Duplex stainless steels. Grain size examination is only addressed for austenitic materials, not duplex steels. Source: DMV_STANDA...

Open

240

4.4.1

AI

No

add date

No information confirming the use of 20-40% NaOH or KOH solution or other suitable etchants as per ISO 17781 Appendix B for micrographic examination or to reveal ferrite balance and intermetallic phases is provided. Source: DMV_STANDARD_BOOK/12 - Spe...

Open

241

4.4.2

AI

No

add date

The micrographic examination section requires the microstructure to be basically free from intermetallic precipitates, allowing isolated precipitates if not homogeneously distributed and each is below 10 μm, matching the client's requirement exactly....

Open

242

4.4.2

AI

No

add date

No evidence that the presence and location of intermetallic phases are noted and recorded with micrographs at 400x or higher magnification; only grain size measurement is addressed and no relevant engineering comments are provided. Source: DMV_STANDA...

Open

243

4.4.2

AI

No

add date

Micrographic examination at a minimum of 400x magnification and inclusion of photos are specified, but it is not explicitly stated that a representative micrograph at or near mid-wall thickness is recorded when intermetallic phases are not detected, ...

Open

244

4.4.2

AI

No

add date

No provided documents address the reporting or acceptance criteria for centerline intermetallic stringers, nor do they link acceptance to CVN or corrosion test results in their presence. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in ...

Open

245

4.4.2

AI

No

add date

Referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or allow isolated intermetallic precipitates under certain conditions, which does not meet the stricter client requi...

Open

246

4.4.3

AI

No

add date

No evidence of ferrite content measurement by ASTM E 562, ASTM E 1245, or ISO 17781 is provided; only grain size measurement is discussed or no relevant information is available. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive test...

Open

247

4.4.3

AI

No

add date

No provided document specifies acceptance criteria or results for micrographic examination or metallurgical properties relevant to DMV 25.7N; grain size examination is also stated as not applicable to duplex/super-duplex stainless steels in the refer...

Open

248

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

249

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are provided; only a heading is present without detailed requirements or values. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/0...

Open

250

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria: no pitting at 20X magnification and weight loss < 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

251

5.1

AI

No

add date

No provided documents contain information on the qualification or certification of NDE personnel to ISO 9712 level II or III, or their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, ...

Open

252

5.2

AI

No

add date

No evidence provided that 100% ultrasonic testing for longitudinal defects will be performed in accordance with ASTM E213 or ISO 10893-10, or that reference notches and test timing requirements are met. Source: DMV_STANDARD_BOOK/12 - Special Testing/...

Open

253

5.2

AI

No

add date

Dye penetrant testing is available for tube ends and bevels on request, matching the client inquiry which does not require full-length testing. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-05 - Dye penetrant te...

Open

254

5.2

AI

No

add date

No provided document confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor do they specify acceptance criteria or relevant NDE procedures for the requested dimension at Montbard. NDE...

Open

255

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for hot and cold finished products are confirmed as per the applicable ASTM standards (including ASTM A790/A999) for the relevant dimensions, with no deviations or TechnipFMC overrides indicated. Source:...

Open

256

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed (ASTM A790) and white pickled or bright annealed (NORSOK MDS S01), directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790, NORSOK MDS S01.

Open

257

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS S01 Rev 05 for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 ....

Open

258

10.0

AI

No

add date

No evidence of an appropriate quality-assurance system (such as ISO 9001 certification by a competent EEA body) is provided for the Montbard plant or manufacturer; referenced documents do not contain certification details or confirmation of complianc...

Open

259

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

260

10.1

AI

No

add date

No evidence that the material manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body as required by the specification or that required documentation is submitted to TechnipFMC for approval. Source: DMV_STANDARD_BOOK/1...

Open

261

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

262

10.2

AI

No

add date

No evidence that documentation traceable to the products and to be transmitted to TechnipFMC (SIR205) will be provided as required by the specification section 10.0. Types of certificates and inspection are listed, but explicit fulfillment of the req...

Open

263

10.2

AI

No

add date

Material certificate is issued according to EN 10204 Type 3.1 and validated by Quality Control for mill inspection. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-03 - Certifica...

Open

264

10.2

AI

No

add date

None of the provided documents contain the required documentation or certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing paramete...

Open

265

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured and tested in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with all relevant mechanical, chemical, corrosion, and qualification requirements met, including M-650 qualification up to the req...

Open

266

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782, as required. No confirmation of QTR/MPCR availability for review is provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

267

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

268

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

269

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 06, including PREN ≥ 40 and all specified element limits and ranges. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 ...

Open

270

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

271

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

272

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

273

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure, is performed per NORSOK MDS D51/ASTM A790 requirements. For the ordered pipe d...

Open

274

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

275

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

276

4.3

AI

No

add date

Charpy V-notch testing in accordance with ASTM A370 and ISO 148-1 is feasible for the specified pipe dimensions and can be performed as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03...

Open

277

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible), for thickness ≥6 mm. The specified p...

Open

278

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

279

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

280

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

281

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

282

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

283

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

284

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates, which does not meet the stricter client requirement of no intermetallics or...

Open

285

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

286

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

287

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

288

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

289

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

290

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

291

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

292

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects is performed in accordance with ASTM E213 and ISO 10893-10 after all processing steps, and the dimensional range is covered. Reference notches and calibration are in line with ASTM E213 requirements. S...

Open

293

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially met via 100% hydrostatic or NDE (EC or UT) testing, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the reque...

Open

294

5.2

AI

No

add date

None of the relevant documents explicitly confirm that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor do they confirm the required NDE acceptance criteria or feasibility fo...

Open

295

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and referenced ASTM A999, as required, with no overriding specifications from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according ...

Open

296

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring compliance with the requirement for traceab...

Open

297

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORS...

Open

298

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

299

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

300

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV25.7N, and the EN 10204 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

301

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

302

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

303

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - ...

Open

304

10.2

AI

No

add date

EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the actual steel producer's name. No specific do...

Open

305

1.0

AI

No

add date

DMV 25.7N seamless pipe is specified as compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, with M-650 qualification confirmed for the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

306

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence provided for QTR/MPCR availability or full compliance with both standards as required by the specification. Source: DMV_STANDARD_...

Open

307

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N, with manufacturing process qualified to M-650 (or ISO 17782), and compliance with NORSOK M-630 MDS D51 Rev. 6 is confirmed. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

308

3.1

AI

No

add date

Chemical composition for S32760 matches Table 2 requirements and is confirmed to conform per heat analysis for DMV material. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ...

Open

309

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

310

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

311

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

312

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests are performed at the spec...

Open

313

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

314

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

315

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, as the wall thickness exceeds the minimum required by the standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 ...

Open

316

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact test requirements at -46°C, with minimum absorbed energy values for both transverse and longitudinal directions. The specified pipe wall thickness (18.26mm) allows for the required impact testing a...

Open

317

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 will be performed or is referenced. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

318

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

319

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is specified and fulfills the requirement for suitable etchant(s) as listed in ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

320

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

321

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

322

4.4.2

AI

No

add date

Micrographs at a minimum magnification of 400x are included, reported at actual magnification with a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

323

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

324

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates, which does not meet the stricter client requirement of not permitting any i...

Open

325

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

326

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

327

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

328

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, as well as manufacturing, heat treatment, and qualification requirements. Source: DMV_STAN...

Open

329

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A @ 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², both of which are met. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

330

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

331

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 or ISO 10893-10 is feasible and standards-compliant for the specified pipe dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Sourc...

Open

332

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: ASTM A 790.docx, NORSOK MDS D51 Rev 06.docx

Open

333

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790, NORSOK M-630 MDS D51 Rev 6, and NORSOK M-650/ISO 17782 are not confirmed as fulfilled; available documentation only partially covers NDE per ASTM A790/A999 and does not confirm compliance with NORSOK requirement...

Open

334

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor is there confirmation that the required NDE is standardly performed or feasible...

Open

335

6.0

AI

No

add date

Dimensional tolerances are specified as per ASTM A790 and ASTM A999, with no alternative tolerances from TechnipFMC stated. Requirement is fulfilled as tolerances follow the applicable ASTM standard unless otherwise specified, which is not the case h...

Open

336

8.0

AI

No

add date

Marking per ASTM A790 includes heat and lot numbers, ensuring full traceability to melt and heat treatment lot; standard marking methods (indelible ink, vibro-etching) at Montbard include these identifiers as required. Source: DMV_STANDARD_BOOK/02-04...

Open

337

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' in the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

338

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

339

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

340

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the specified wall thickness, and the QTR number is included as per M-650 qualification, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/M...

Open

341

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, are provided and meet the requirement for transmission and traceability to TechnipFMC as per S...

Open

342

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification summary. Source: DMV_STANDARD_BOOK...

Open

343

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution annealing temperature/hold...

Open

344

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified for the required wall thickness. Source: DMV_S...

Open

345

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability. Requirement for NORSOK M-650/ISO 17782 qualification and documentation availability is not fully m...

Open

346

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

347

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

348

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat, confirming conformity to the required ...

Open

349

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

350

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

351

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

352

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed as required, w...

Open

353

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 as required by NORSOK MDS D51 and ASTM A790 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

354

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 06 and ASTM A790 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

355

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

356

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energy values for both transverse and longitudinal directions, and the specified pipe dimensions allow for required testing directions and valu...

Open

357

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

358

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

359

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

360

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

361

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

362

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

363

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

364

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates, which does not meet the stricter client requirement of not permitting any i...

Open

365

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

366

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

367

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% and DMV 25.7N complies per ISO 17781/ASTM E1245 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

368

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified per NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

369

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

370

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source: DMV_STAN...

Open

371

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

372

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/650 are not fully addressed; only general hydrostatic or NDE (EC/UT) per ASTM A999 is confirmed, with no explicit evidence for NORSOK-specific requirements. For the requested OD, eddy cur...

Open

373

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor that this NDE acceptance criterion is standardly performed or feasible for the specified pipe di...

Open

374

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the requested pipe, with no evidence of a different requirement from TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - ...

Open

375

8.0

AI

No

add date

Marking per ASTM A790 and plant practices includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-...

Open

376

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

377

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA and specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

378

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

379

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, and the QTR number is included in the certificate, fulfilling the requirement for supplier qualification documentation per SIR131. Source: DMV_STANDARD_BOOK/0...

Open

380

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products, fulfilling SIR205 and specification requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORS...

Open

381

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 qualification summary. Source:...

Open

382

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and...

Open

383

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all standard and supplementary requirements, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/...

Open

384

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

385

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

386

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C (transverse: 45/35 J, longitudinal: 65/50 J) for thickness >6mm, and the specified pipe dimensions allow for required testing directions and specimen sizes. Source: D...

Open

387

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected, fulfilling the requirem...

Open

388

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

389

1.0

AI

No

add date

Supplier is M-650 accredited for DMV25.7N but not accredited to ISO 17782 as required; full qualification per NORSOK M-650/ISO 17782 is not demonstrated. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

390

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

391

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

392

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits and PREN ≥ 40 as specified in Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 6 requirements for S32760. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D...

Open

393

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification will state heat treatment condition as per ASTM A790. Pipes are processed to ensure ...

Open

394

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

395

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

396

4.1

AI

No

add date

Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, are fulfilled for DMV 25.7N. The...

Open

397

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with material meeting the tensile and maximum hardness properties of Table 4 as required by NORSOK MDS D51. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

398

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

399

4.3

AI

No

add date

The pipe wall thickness exceeds the minimum required for Charpy V-notch testing, and the plant confirms feasibility for Charpy testing per ASTM A370 or ISO 148-1. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

400

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, with minimum absorbed energy values for both transverse and longitudinal specimens, and the specified pipe dimensions allow for required testing directions. Source:...

Open

401

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

402

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

403

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

404

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782 as required; no evidence provided for availability of QTR/MPCR for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

405

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

406

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

407

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

408

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size. No other relevant information addresses the re...

Open

409

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

410

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

411

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

412

4.5

AI

No

add date

No explicit evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or documented for the requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

413

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, with M-650 qualification for the specified grade and wall thickness. Source: DMV_STANDARD_...

Open

414

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A @ 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and complies with these requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

415

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

416

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within capability range. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02...

Open

417

5.2

AI

No

add date

NDE per ASTM A790 is partially addressed with hydrostatic or NDE (EC or UT) per ASTM A999, but there is no explicit evidence of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements. Eddy current testing is no...

Open

418

5.2

AI

No

add date

No provided document explicitly states that any indication greater than the calibration notch is considered a defect requiring rejection or repair; NDE acceptance criteria and process capability do not fulfill the requirement for the specified pipe s...

Open

419

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790) for the specified pipe size, with no deviations or special requirements from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General informatio...

Open

420

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

421

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

422

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

423

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

424

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

425

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV25.7N, and the EN 10204 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number for the specified size and product form. Source: DMV_ST...

Open

426

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability information, fulfilling the requirement for documentation traceable to delivered products and transmission to TechnipFMC. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

427

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications and plant documentation. Source: DMV_STANDARD_BOOK/02-04-03 - Dig...

Open

428

10.2

AI

No

add date

Most documentation and certification requirements are stated as included in the EN 10204 type 3.1 certificate, except the steel producer of the starting material, which is not provided (only country of origin is given). No specific evidence is provid...

Open

429

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

430

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

431

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

432

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

433

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

434

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

435

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with frequency and method matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

436

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, is fulfilled for DMV 25.7...

Open

437

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

438

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: minimum tensile strength 750 MPa, yield strength 550 MPa, elongation 25%, and maximum hardness 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

439

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370 and ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03...

Open

440

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal. The specified pipe dimensions allo...

Open

441

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed according to ISO 17781 with 20-40% NaOH or KOH solution after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

442

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

443

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

444

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases. Source: DMV_STANDARD_BOOK/02...

Open

445

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

446

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

447

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement does not permit any intermetallic phases or precipitates if CVN testing cannot be completed, so the requirement is not fully fulfilled. Source: DMV_S...

Open

448

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

449

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

450

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

451

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or confirmed in the referenced documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

452

4.5

AI

No

add date

All metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, microstructure, PRE, solution annealing, and ferrite content, are fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

453

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A @ 50°C, 24h) is performed for DMV 25.7N, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and DMV 25.7N complies with these requirements. Source: DMV_STANDARD_BOOK/02 -...

Open

454

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

455

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

456

5.2

AI

No

add date

NDE per NORSOK M-630 MDS D51/ASTM A790 is not confirmed; only ASTM A790/A999 NDE is detailed, destructive tests are described but not NDE, standard NDE (ultrasonic, eddy current) is not available or only at extra cost for the required OD, and full-le...

Open

457

5.2

AI

No

add date

No provided documentation confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor is there confirmation that such NDE acceptance criteria are standardly performed or f...

Open

458

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are per ASTM A790 and referenced ASTM A999, with no deviations specified in the customer requirements, fulfilling the requirement for ASTM standard tolerances unless otherwise stated. Source: DMV_STANDAR...

Open

459

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

460

8.0

AI

No

add date

Marking per ASTM A790 and plant marking methods ensure mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDA...

Open

461

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

462

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

463

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

464

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV25.7N up to 31.75 mm WT, covering the required 18.26 mm, and the EN 10204 3.1 certificate will include the NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, demonstr...

Open

465

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products being delivered as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

466

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference. Source: D...

Open

467

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all required metallurgic...

Open

468

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification digest and the listing of 'A790 NORSOK' under customer specifications. Manufacturing is M-650 qualified for th...

Open

469

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev...

Open

470

4.1

AI

No

add date

Test sampling for seamless pipes per ASTM A790 and NORSOK MDS D51 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations. Fo...

Open

471

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

472

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

473

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is fulfilled or documented for the requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

474

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, performed after all mechanical processing, meeting the requirement for 100% longitudinal defect detection. Source: DMV_STANDARD_BOOK/12 -...

Open

475

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

476

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782 as required; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

477

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

478

3.1

AI

No

add date

AOD or equivalent refining is used 100% for DMV 25.7N, and chemical composition complies with Table 2 of ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

479

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Heat analysis is performed per heat and matches the specified limits for all elements listed in the...

Open

480

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - S...

Open

481

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

482

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

483

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests, with specified locations and directions, is fulfilled for DMV 25.7N per ...

Open

484

4.2

AI

No

add date

Tensile testing is performed at room temperature per required standards, with mechanical properties and hardness requirements matching Table 4; compliance with ASTM A370 or ISO 6892-1 and NORSOK MDS D51 is confirmed. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

485

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: yield strength ≥ 550 MPa, tensile strength ≥ 750 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW, fulfilling all specified mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

486

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfills the requirement as the pipe wall thickness exceeds the minimum required by ASTM and ISO standards for such testing. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

487

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C (transverse: 45 J avg/35 J single, longitudinal: 65 J avg/50 J single) for thickness >6 mm. The specified pipe dimensions allow for required testing directions and s...

Open

488

4.4.1

AI

No

add date

Micrographic examination and ferrite check are performed as per ISO 17781, but the exact etchant solution and procedure required for intermetallic phase detection and ferrite balance after final polishing are not fully specified as per the client's r...

Open

489

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is explicitly required for micrographic examination as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

490

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

491

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

492

4.4.2

AI

No

add date

Micrographs at a minimum magnification of 400x are included, reported at actual magnification with a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

493

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

494

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

495

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

496

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corro...

Open

497

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

498

4.5

AI

No

add date

ASTM G48 Method 'A' corrosion testing at 50°C for 24h in accordance with ISO 17781 is not explicitly mentioned or confirmed; compliance cannot be validated based on the available information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Mon...

Open

499

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, chemical composition, ferrite content, and corrosion/impact requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

500

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A @ 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

501

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

502

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is confirmed, performed after all mechanical processing, and applicable to the specified pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/...

Open

503

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE acceptance criteria are addressed. For the requested OD, standard NDE (eddy current, ultrasonic, hydrostatic) is not avail...

Open

504

5.2

AI

No

add date

No provided documentation explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect and that such pipe or tubing is rejected or repaired, nor is there confirmation that the required NDE is stan...

Open

505

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

506

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and ASTM A999 as required, with no deviations specified by TechnipFMC. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ...

Open

507

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

508

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02...

Open

509

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 explicitly states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

510

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

511

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

512

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size ...

Open

513

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

514

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630 for 25Cr Duplex Stainless Steel seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-0...

Open

515

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of required metallurgical and non-destructive testing for the specific mate...

Open

516

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all standard and supplementary requirements. M-650 qualification is confirmed for the required wall thickness. Source: DMV_STANDARD_...

Open

517

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

518

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

519

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

520

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements. Heat analysis is performed per heat as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 ...

Open

521

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

522

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

523

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-0...

Open

524

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes meets NORSOK MDS D51/ASTM A790 requirements: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure at specified locations. For the or...

Open

525

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

526

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

527

4.3

AI

No

add date

Pipe wall thickness (18.26 mm) exceeds the minimum required for Charpy V-notch testing per ASTM and ISO standards; plant confirms feasibility for >6 mm WT. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

528

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, including minimum absorbed energies for both transverse and longitudinal directions, and the specified product dimensions allow for required testing orientations. So...

Open

529

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with specified etchants for intermetallic phases and ferrite balance after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spec...

Open

530

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is explicitly required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_...

Open

531

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

532

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases. Source: DMV_STANDARD_BOOK/02...

Open

533

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included at actual magnification and a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

534

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

535

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm if not distributed over the whole specimen, whereas the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefor...

Open

536

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

537

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Structure must be basically free from intermetallic precipitates; isolated precipitates allowed if not d...

Open

538

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

539

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is fulfilled or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

540

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified per NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

541

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A @ 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

542

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712 or equivalent. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing...

Open

543

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions and is performed after all mechanical processing, heat treatment, and straightening, as required. Source: DMV_STANDARD_BOOK/12 - Special T...

Open

544

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed. Provided documents only partially address ASTM A790 NDE, do not specify required NDE methods or acceptance criteria, and indicate feasibility issues for ed...

Open

545

5.2

AI

No

add date

No provided documentation explicitly confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that such NDE acceptance criteria are standardly performed or feasible for the requested pipe ...

Open

546

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790/A999) for the specified pipe dimensions, with no deviations or special requirements stated by the customer. Source: DMV_STANDARD_BOOK/07-01 - General information.d...

Open

547

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

548

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

549

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required for DMV 25.7N seamless pipe under NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

550

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or confirmed. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

551

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

552

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

553

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV 25.7N, with certification including the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number for the specified size and product form. Source: DMV_STANDARD_BOOK/02 -...

Open

554

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

555

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - ...

Open

556

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or required test results. Only the country of origin of the steel supplier is stated, not...

Open

557

1.0

AI

No

add date

DMV 25.7N seamless pipes are 25 Cr Duplex stainless steel, manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with M-650 qualification up to the required wall thickness. Source: Item Tabl...

Open

558

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence provided for QTR/MPCR availability or full compliance with both standards as required by the specification. Source: DMV_STANDARD_BO...

Open

559

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

560

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

561

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PREN ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

562

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

563

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

564

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the specified frequency, demonstrating compliance with the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

565

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, meeting the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

566

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per NORSOK MDS D51/ASTM A7...

Open

567

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

568

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW, as confirmed in the destructive testing table and specification alignment with ASTM A790. ...

Open

569

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness required by the standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - ...

Open

570

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for required testing directions and specimen sizes. ...

Open

571

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

572

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

573

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

574

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

575

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included at actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDARD_BOO...

Open

576

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_ST...

Open

577

4.4.2

AI

No

add date

The available documentation does not explicitly prohibit all intermetallic phases and/or precipitates if CVN testing cannot be completed; isolated precipitates are still allowed under certain conditions, which does not meet the stricter client requir...

Open

578

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

579

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: microstructure examination per ISO 17781 with specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrid...

Open

580

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 06 are fully met, including compliance for destructive and microstructural tests (tensile, impact, corrosion, microstructure, ferrite). Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

581

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

582

5.1

AI

No

add date

No evidence provided regarding qualification or certification of NDE personnel to ISO 9712 level II or III, or definition of their roles and responsibilities per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Mo...

Open

583

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 or ISO 10893-10 is feasible and standards-compliant for the specified pipe dimensions; calibration is assumed to follow ASTM E213 Figure 3 as required. Source: DMV_STANDARD...

Open

584

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/650 are not fully addressed. Standard NDE (EC or UT) is not feasible for OD 219.1 mm at Montbard without extra cost or technical consultation, and full-length dye penetrant testing is not...

Open

585

5.2

AI

No

add date

No document explicitly confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor that this NDE acceptance criterion is standardly performed or feasible for the requested dimension at Mon...

Open

586

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a A ...

Open

587

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

588

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

589

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

590

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

591

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body established within the EEA, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-...

Open

592

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

593

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

594

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630 for 25Cr Duplex Stainless Steel seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-0...

Open

595

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive te...

Open

596

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all standard, supplementary, and qualification requirements for 25 Cr Duplex stainless steel seamless pipes. Source: DMV_STANDARD_BOOK/02-03-01 - D...

Open

597

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782 as required; no evidence provided for QTR/MPCR availability for review by TechnipFMC or full compliance with both standards and documentation requirements. Source: DMV_STANDARD...

Open

598

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, with qualification testing meeting NORSOK M-630 MDS D51 rev. 6 requirements. Sour...

Open

599

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

600

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and DMV material composition conforms with supplier certification and heat analysis per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02...

Open

601

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

602

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

603

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

604

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is performed per NORSOK MDS D51/ASTM A790. Fo...

Open

605

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

606

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

607

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions (18.26mm WT, 219.1mm OD) in both longitudinal and transverse directions as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - D...

Open

608

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact test requirements at -466C (minimum 45 J average/35 J single transverse, 65 J average/50 J single longitudinal, sub-size reduction factors included), and the specified pipe dimensions allow for re...

Open

609

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with specified etchants after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

610

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, is specified and matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

611

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

612

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

613

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

614

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK/0...

Open

615

4.4.2

AI

No

add date

No evidence that intermetallic phases and/or precipitates are completely prohibited if CVN testing cannot be completed; existing specifications allow isolated precipitates below 10 µm, which does not meet the stricter client requirement. Source: DMV_...

Open

616

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

617

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 at ≥400X magnification, with acceptance criteria requiring the structure to be basically free from intermetallic precipitates (isolated precipitates <10µm allowed if not distributed over the whole...

Open

618

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS ...

Open

619

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is fulfilled; neither ASTM G48 nor ISO 17781 nor the specific test conditions are mentioned in the relevant documentation. Source: DMV_STANDARD_BOOK/1...

Open

620

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

621

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A @ 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/0...

Open

622

5.1

AI

No

add date

No evidence provided regarding qualification or certification of NDE personnel to ISO 9712 level II or III, nor definition of their roles and responsibilities as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

623

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 can be performed after all processing, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destru...

Open

624

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no explicit confirmation of compliance with NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 NDE requirements. Eddy current testing is not feasible for the requested OD, and hydrostatic/ultrasonic tests are...

Open

625

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor is there confirmation that the required NDE acceptance criterion is standard or...

Open

626

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the requested pipe, with no evidence of a deviation or override in the customer specification. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BO...

Open

627

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

628

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot, and standard marking methods (indelible ink, vibro-etching) include heat and lot numbers as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

629

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

630

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

631

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

632

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

633

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

634

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51...

Open

635

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness requirements for transverse specimens. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destru...

Open

636

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements, including Charpy V-notch testing at -46°C with specified minimum absorbed energy values for both transverse and longitudinal directions. The requested pipe dimensions allow for both t...

Open

637

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all required metallurgic...

Open

638

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by both the inquiry metadata and technical digests. All relevant chemical, mechanical, manufacturing, and testing requirements a...

Open

639

1.0

AI

No

add date

No evidence is provided that the supplier is qualified to both NORSOK M-650 and ISO 17782, nor is there confirmation of QTR/MPCR documentation availability as required by the specification. MST-Tubes is only M-650 accredited, not ISO 17782 accredited...

Open

640

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

641

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

642

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements, with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/0...

Open

643

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

644

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

645

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

646

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests, with specified locations and directions, is fulfilled for DMV 25.7N per ...

Open

647

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with material meeting the specified tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

648

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, fulfilling the client's mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

649

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

650

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching for intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and examination in accordance ...

Open

651

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, is specified and matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

652

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

653

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are reported with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

654

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

655

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK/0...

Open

656

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

657

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

658

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance is based on impact and ...

Open

659

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is fulfilled for DMV 25.7N as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

660

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

661

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

662

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

663

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in...

Open

664

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions and is performed after all mechanical processing. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 ...

Open

665

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or confirmed. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

666

5.2

AI

No

add date

No evidence that NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782 are addressed or fulfilled. For the specified OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available a...

Open

667

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair; standard NDE method (Eddy current) is not feasible for the requested OD at Montbard, so compliance with the requirement...

Open

668

6.0

AI

No

add date

Dimensional tolerances are confirmed as per the applicable ASTM standard (ASTM A999 for ASTM A790 pipe), with no deviations or overrides specified by the customer. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 ...

Open

669

7.0

AI

No

add date

ASTM A790 (6.1.3) and NORSOK MDS D51 (§13) both require finished pipes to be pickled or bright annealed, fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

670

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods include heat number and DMV lot number, ensuring traceability as required by the specification. Certif...

Open

671

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

672

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

673

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-...

Open

674

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified ...

Open

675

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

676

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing M-650/ISO17782 qualification where applicable. Source: DMV_STANDARD_BOOK/02-04-03 -...

Open

677

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all required metallurgical and non-destruc...

Open

678

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all referenced mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified up to the required wal...

Open

679

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

680

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

681

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including all specified element limits and PREN ≥ 40, as required by the specification table. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev ...

Open

682

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

683

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

684

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

685

4.1

AI

No

add date

Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions, are fulfilled for DMV...

Open

686

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the specified tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

687

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW, fulfilling all specified mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

688

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness (>6mm), meeting the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Imp...

Open

689

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06, requiring Charpy V-notch impact testing at -46°C with minimum absorbed energy values (transverse: 45 J average/35 J single, longitudinal: 65 J average/50 J single if transverse not possible), and reducti...

Open

690

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants and electrolytic etching after final polishing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

691

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is explicitly required and matches the specification requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

692

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

693

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

694

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

695

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

696

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

697

4.4.2

AI

No

add date

No provided document fully prohibits intermetallic phases and/or precipitates when CVN testing cannot be completed; allowance for isolated precipitates does not meet the requirement for total prohibition in this case. Source: DMV_STANDARD_BOOK/02-03-...

Open

698

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

699

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and ...

Open

700

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

701

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or referenced; compliance cannot be confirmed based on the provided information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in M...

Open

702

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

703

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

704

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source: DM...

Open

705

5.2

AI

No

add date

Ultrasonic testing per ASTM E213 and ISO 10893-10 is available for the specified OD, WT, and length, and is performed after all mechanical processing as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03...

Open

706

5.2

AI

No

add date

NDE per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 is not confirmed; only ASTM A790/A999 NDE is detailed. Eddy current testing is not feasible for the required OD at Montbard, and hydrostatic/ultrasonic tests are only available at extra co...

Open

707

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair, and no evidence that the required NDE can be performed as standard for the specified OD at the plant. NDE acceptance cr...

Open

708

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a A ...

Open

709

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

710

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

711

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

712

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

713

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

714

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV25.7N up to WT = 31.75 mm, and the EN 10204 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

715

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

716

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference. Source: DMV_STANDARD_BO...

Open

717

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice and refining method, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel produ...

Open

718

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with all relevant mechanical, chemical, and testing requirements addressed. Source: DMV_STANDA...

Open

719

1.0

AI

No

add date

No evidence that the supplier is qualified to NORSOK M-650/ISO 17782 for the exact product supplied or that Qualification Test Record/MPCR documentation is available for review. One source confirms NORSOK M-650 accreditation but not ISO 17782, which ...

Open

720

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm for hot finished, 10.925 mm for cold finished), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 requirements w...

Open

721

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

722

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N complies with the specified chemical composition requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-0...

Open

723

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the required WT of 18.26 mm for the inquiry. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-...

Open

724

3.2

AI

No

add date

Solution annealing followed by accelerated cooling is standard for DMV 25.7N per ASTM A790; manufacturing process and furnaces are qualified to NORSOK M-650; free circulation of heating/cooling media is ensured by compliance with these standards and ...

Open

725

4.1

AI

No

add date

No provided document confirms that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is carried out for each heat and heat treatment lot as defined in ASTM A790. There is no explicit evidence of compliance with ...

Open

726

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

727

4.1

AI

No

add date

Tensile test sampling is confirmed per ASTM A790, but there is no evidence of CVN impact testing, test directions, or detailed thickness location requirements being addressed. Corrosion and microstructure sampling are also not covered. Source: DMV_ST...

Open

728

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-...

Open

729

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required in Table 4 are not confirmed or are lower than required in the provided documents. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_...

Open

730

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, meeting the minimum wall thickness requirements for both standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testi...

Open

731

4.3

AI

No

add date

Pipe dimensions allow for transverse Charpy V-notch specimens; impact property requirements at -46°C are feasible and can be fulfilled for this product. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

732

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination according to ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - ...

Open

733

4.4.1

AI

No

add date

No information confirming the use of 20-40% NaOH or KOH solution or other suitable etchants as per ISO 17781 Appendix B for micrographic examination is provided or referenced. Requirement not fulfilled for etchant specification or procedure to show f...

Open

734

4.4.2

AI

No

add date

The microstructure must be basically free from intermetallic precipitates, but isolated precipitates are allowed if not distributed over the whole specimen and if the dimension of each precipitate is below 10 μm, matching the requirement exactly. Sou...

Open

735

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided or addressed in the relevant documentation.

Open

736

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at actual magnification with a scale bar when intermetallic phases are not detected; minimum 400x magnification and inclusion of photos are mentioned,...

Open

737

4.4.2

AI

No

add date

No provided documents address the reporting of centerline intermetallic stringers or specify acceptance criteria based on CVN and corrosion test results in case such stringers are present. Requirement not fulfilled. Source: DMV_STANDARD_BOOK/12-03-03...

Open

738

4.4.2

AI

No

add date

Relevant specifications allow isolated intermetallic precipitates below 10 µm if not distributed over the whole specimen, which does not meet the stricter client requirement that prohibits any intermetallic phases and/or precipitates if CVN testing c...

Open

739

4.4.3

AI

No

add date

No evidence of ferrite content measurement by ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided; only grain size measurement is addressed, not ferrite content determination by the specified methods or standards. Source: DMV_STANDARD_...

Open

740

4.4.3

AI

No

add date

No provided document addresses or confirms acceptance criteria for micrographic examination or metallurgical properties for DMV 25.7N as required in section 4.4. No evidence of fulfillment for micrographic examination acceptance criteria at Montbard ...

Open

741

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, ...

Open

742

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided; only A790 NORSOK is referenced, which does not cover this requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plan...

Open

743

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are defined in the provided context, so fulfillment cannot be determined or validated against the requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK...

Open

744

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 G48 Method A at 25°C for 24 hours is required, with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the client's requirements. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

745

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDA...

Open

746

5.2

AI

No

add date

No evidence is provided confirming 100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10, nor the required reference notch criteria and test timing after all processing steps are addressed. Source: DMV_STANDARD_BOOK/12 - Spec...

Open

747

5.2

AI

No

add date

100% qualitative anti-mixing PMI checks are standard at Montbard, with defined procedures and reporting for quantitative PMI, meeting NDE acceptance criteria. Source: DMV_STANDARD_BOOK/12-06-06 - Positive Material Identification (PMI) in Montbard.doc...

Open

748

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair for the specified pipe; NDE feasibility and acceptance criteria are not explicitly addressed fo...

Open

749

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

750

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

751

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - S...

Open

752

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for the requested product are confirmed as per the applicable ASTM standards (including ASTM A790/A999) for the relevant size range, with no overriding TechnipFMC specification indicated. Requirement is ...

Open

753

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790, NORSOK MDS S01

Open

754

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

755

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

756

10.0

AI

No

add date

No evidence of an appropriate quality-assurance system (such as ISO 9001 certification by a competent EEA body) is provided for the Montbard plant or manufacturer. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - C...

Open

757

10.1

AI

No

add date

No evidence that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body with specific assessment for materials is provided. Source: DMV_STANDARD_BOOK/14-03 - Certification Montbard plant.doc

Open

758

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N up to WT 31.75 mm (requested WT 18.26 mm), and the EN 10204 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number for the size and produc...

Open

759

10.2

AI

No

add date

No explicit confirmation that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205; available documents only describe types of certificates and validation bodies without addressing transmission or traceabili...

Open

760

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include information required by ASTM A790 and NORSOK M-630 for DMV 25.7N products as referenced in the specification. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/14-03 -...

Open

761

10.2

AI

No

add date

No provided document contains the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or metallurgical and non-de...

Open

762

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured and tested in compliance with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, with all relevant requirements met, including M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

763

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS...

Open

764

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

765

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

766

4.1

AI

No

add date

Test specimen sampling is performed according to Table 3, with specified frequency for tensile tests, fulfilling the requirement for test specimen sampling as outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 ...

Open

767

4.1

AI

No

add date

Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions, are fulfilled for DMV...

Open

768

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 as required by NORSOK MDS D51 and ASTM A790 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

769

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 06 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

770

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

771

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -466C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if transvers...

Open

772

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

773

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-0...

Open

774

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

775

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

776

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, reported at actual magnification and including a scale bar, and structure free from intermetallic precipitates. Source: DMV_STANDARD_...

Open

777

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

778

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

779

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

780

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

781

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Acceptance criteria: structure must be basically free from intermetallic precipitates (isolated, non-dis...

Open

782

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in accordance with ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

783

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

784

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, including chemical composition, mechanical properties, impact, corrosion, microstructure, ferrite content, and qualification requirements (M-650 up ...

Open

785

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

786

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destru...

Open

787

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is available, including reference notches and calibration as per ASTM E213, and the pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02...

Open

788

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD, standard NDE (eddy current, ultrasonic, hydrostatic) is not ava...

Open

789

5.2

AI

No

add date

None of the relevant documents explicitly state that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair of the pipe or tubing, nor do they confirm that NDE with this acceptance criteri...

Open

790

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A ...

Open

791

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

792

8.0

AI

No

add date

Marking is performed per ASTM A790 §14 and includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_...

Open

793

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

794

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

795

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

796

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the specified quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

797

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

798

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

799

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

800

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, steel melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destruct...

Open

801

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all relevant chemical, mechanical, manufacturing, and testing requirements. M-650 qualification is confirmed for the required wall thickness. Source...

Open

802

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence provided for QTR/MPCR availability or full compliance with both standards as required by the specification. Source: DMV_STANDARD_...

Open

803

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

804

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition conforms to the specified requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

805

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PREN ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

806

3.2

AI

No

add date

Heat treatment is solution annealing followed by accelerated cooling (water quenching) per ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650/ISO 17782, and proper pipe placement during heat treatment is ensured. Source: DMV...

Open

807

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

808

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ...

Open

809

4.1

AI

No

add date

Test sampling for seamless pipes per ASTM A790 and NORSOK MDS D51 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness loc...

Open

810

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

811

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: minimum tensile strength 750 MPa, yield strength 550 MPa, elongation 25%, and maximum hardness 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

812

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370 and ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03...

Open

813

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, with minimum absorbed energy values for transverse and longitudinal directions, and the specified pipe dimensions allow for required testing directions and specimen...

Open

814

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

815

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

816

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

817

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs are included as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

818

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

819

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

820

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. The requirement is not fully met. ...

Open

821

4.4.3

AI

No

add date

Ferrite content is checked as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis per ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

822

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 at ≥400X magnification, with acceptance criteria requiring the structure to be basically free from intermetallic precipitates (isolated precipitates allowed if <10µm and not distributed over the w...

Open

823

4.5

AI

No

add date

ASTM G48 Method 'A' corrosion testing at 50°C for 24h in accordance with ISO 17781 is not explicitly mentioned or referenced, so compliance cannot be confirmed. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

824

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including chemical composition (PRE ≥ 40), mechanical properties, microstructure, ferrite content (35-60%), and corrosion resistance; manufacturing process is M-650 quali...

Open

825

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

826

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

827

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is performed after all mechanical processing, heat treatment, and straightening, and the dimensional range is within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing...

Open

828

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled; available documentation only covers ASTM A790/A999 or lacks explicit confirmation for NORSOK compliance. Eddy current testing is not fea...

Open

829

5.2

AI

No

add date

No provided document confirms that indications greater than the calibration notch are classified as defects requiring rejection or repair per the requirement; NDE acceptance criteria are not explicitly detailed or confirmed for the specified product ...

Open

830

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no deviations or overrides specified by TechnipFMC or in the customer specification. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances ac...

Open

831

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

832

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 (§14), requiring traceability to manufacturer, heat, and lot. Standard marking practices at Montbard include heat and DMV lot numbers, ensuring full traceability to melt and heat treatment...

Open

833

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated in the specification under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

834

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body established within the EEA and specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

835

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

836

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV25.7N up to WT = 31.75 mm, covering the inquiry WT of 18.26 mm, and the EN 10204 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR numbe...

Open

837

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

838

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and validated by Quality Control, and will include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-65...

Open

839

10.2

AI

No

add date

Most required documentation and certification details (NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, metallurgical and non-destructive test results) are not provid...

Open

840

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

841

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR availability as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

842

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

843

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard and required for 100% of production, and DMV 25.7N complies with the specified chemical analysis requirements in Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Re...

Open

844

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

845

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

846

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

847

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ...

Open

848

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled for DMV 25.7N per NORSOK MDS D51...

Open

849

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

850

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 and ASTM A790 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW for S32760. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

851

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfilled for the specified pipe dimensions according to ASTM A370 and ISO 148-1 requirements for minimum wall thickness. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Imp...

Open

852

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C, with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal. The specified pipe dimensions allow...

Open

853

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

854

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is explicitly required and matches the specification requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

855

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

856

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

857

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

858

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

859

4.4.2

AI

No

add date

The referenced documents do not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed; isolated precipitates below 10μm are allowed, which does not meet the stricter client requirement of no intermetallics or prec...

Open

860

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

861

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: microstructure examination per ISO 17781 with specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrid...

Open

862

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

863

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

864

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements for ASTM A790 seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

865

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

866

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

867

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is confirmed, applicable after all mechanical processing, and the dimensional range is supported. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03...

Open

868

5.2

AI

No

add date

NDE per ASTM A790 is detailed, but compliance with NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 is not confirmed. For OD 219.1 mm at Montbard, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at extra...

Open

869

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are considered defects requiring rejection or repair; NDE acceptance criteria based on calibration notch are not specified for the requested product and dimension, and feasi...

Open

870

6.0

AI

No

add date

Dimensional tolerances are confirmed as per the applicable ASTM standards (A790 and A999) for the specified product, with no overriding requirements from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_B...

Open

871

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

872

8.0

AI

No

add date

Marking per ASTM A790 ensures full traceability to heat and lot, and mandatory marking of heat number and DMV lot number is implemented, fulfilling the requirement for traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - ...

Open

873

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

874

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

875

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dige...

Open

876

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

877

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

878

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control for mill inspection and referencing relevant standards and qualifications. Source: DMV_STANDARD_BOOK/02-04-03 -...

Open

879

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution annealing temperature/hold...

Open

880

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782, as required. No evidence of QTR/MPCR availability. Source: Digest NORSOK MDS D51 Rev 06.docx

Open

881

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with all relevant mechanical, chemical, and supplementary requirements addressed. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx...

Open

882

1.0

AI

No

add date

No evidence that the supplier is qualified in accordance with NORSOK M-650/ISO 17782 for the exact product supplied or that the full Qualification Test Record/MPCR is available for review. One document confirms M-650 accreditation for UNS S32760/DMV2...

Open

883

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

884

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N meets the chemical composition requirements of Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

885

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the requested product (WT = 18.26 mm). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

886

3.2

AI

No

add date

Solution annealing with water quenching per ASTM A790 is standard for DMV 25.7N, with manufacturing process and furnaces qualified to NORSOK M-650, and pipes arranged for free circulation of heating/cooling media during heat treatment, fulfilling all...

Open

887

4.1

AI

No

add date

No evidence that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790. Only partial or unrelated testing is mentioned, and required testing ...

Open

888

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

889

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no evidence of CVN impact testing, test directions for CVN, or details on thickness location, corrosion, or microstructure sampling as required by the specification. Source: DMV_STANDARD_BOOK/0...

Open

890

4.2

AI

No

add date

Tensile testing is performed at room temperature with criteria (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and frequency (1/lot) for DMV 25.7N, and hardness testing is performed with results in HRC. Testing is in accordance with ASTM A370 or ISO 6892-1,...

Open

891

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required for DMV 25.7N are not confirmed or are not met in the provided sources. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dige...

Open

892

4.3

AI

No

add date

The requested pipe wall thickness exceeds the minimum required for Charpy V-notch testing per ASTM and ISO standards, and the plant confirms feasibility for such testing. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

893

4.3

AI

No

add date

Pipe dimensions allow for transverse Charpy V-notch specimens, so impact property requirements at -46°C are met for both transverse and longitudinal directions as specified. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/1...

Open

894

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

895

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination to ISO 17781 or specified etchant solution for 25 Cr Duplex stainless steels; only grain size measurement for austenitic materials is addressed, not duplex steels. Source: DMV_STANDARD_BOOK/12...

Open

896

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination of ferrite balance and intermetallic phases is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - De...

Open

897

4.4.2

AI

No

add date

Micrographic examination requires the microstructure to be basically free from intermetallic phases, allowing isolated phases if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02-04-...

Open

898

4.4.2

AI

No

add date

No information is provided regarding the detection, recording, or micrographic documentation (at 400x or higher) of intermetallic phases; the requirement is not addressed or fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructiv...

Open

899

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included at actual magnification and a scale bar, fulfilling the requirement for representative micrographs at or near mid-wall thickness if intermetallic phases ar...

Open

900

4.4.2

AI

No

add date

No relevant documents address the requirement to report centerline intermetallic stringers or base acceptance on CVN and corrosion test results if such stringers are present. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I.doc, D...

Open

901

4.4.2

AI

No

add date

Referenced documents allow isolated intermetallic precipitates below 10µm and do not fully prohibit intermetallic phases/precipitates when CVN testing cannot be completed, as required by the client specification. No document fully satisfies the stric...

Open

902

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided; only grain size measurement is addressed, not ferrite content determination by the specified methods or standards. Source: DMV_STANDARD...

Open

903

4.4.3

AI

No

add date

No acceptance criteria for micrographic examination are specified or referenced for DMV 25.7N in the provided documents; only procedures and general information are given without required values or ranges for acceptance. Source: DMV_STANDARD_BOOK/02-...

Open

904

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

905

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided or referenced in the available documentation or metadata. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

906

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are provided in the referenced documents or section, making validation impossible for this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dige...

Open

907

4.5

AI

No

add date

Specification requires pitting corrosion test per ISO 17781 G48 Method A at 25°C for 24 hours, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², matching the client's requirements. Source: DMV_STANDARD_BOOK/02 - ...

Open

908

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Sources only address NDE method feasibility and procedures, not pers...

Open

909

5.2

AI

No

add date

No explicit confirmation of 100% ultrasonic testing per ASTM E213 or ISO 10893-10, calibration notch criteria, or test timing after all processing is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

910

5.2

AI

No

add date

Dye penetrant testing is available for tube ends and bevels on request, and 100% qualitative anti-mixing PMI is performed on standard production, fulfilling the NDE requirements as specified by the client inquiry and context. Source: DMV_STANDARD_BOO...

Open

911

5.2

AI

No

add date

No relevant document confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor that such NDE acceptance criteria are applied for the specified pipe dimension or process capability at Mon...

Open

912

6.0

AI

No

add date

Dimensional tolerances for OD and WT are confirmed as per the applicable ASTM standards (including ASTM A790/A999) for the relevant product dimensions, with no overrides from TechnipFMC indicated. Requirement is fulfilled for both hot and cold finish...

Open

913

7.0

AI

No

add date

Both ASTM A790 and NORSOK MDS S01 require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: ASTM A790 digest, NORSOK MDS S01 Rev 05

Open

914

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

915

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS S01 Rev 05 for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 ....

Open

916

10.0

AI

No

add date

No evidence of an ISO 9001 or equivalent quality-assurance system certified by a competent EEA body or specific assessment for materials is provided in the referenced documents. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_...

Open

917

10.1

AI

No

add date

No confirmation that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification or that documentation will be submitted to TechnipFMC for approval. Source: DMV_STANDARD_BOOK/14-03 - Certification Montbard pla...

Open

918

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV25.7N up to WT = 31.75 mm (requested WT is 18.26 mm), and the EN 10204 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number. Source:...

Open

919

10.2

AI

No

add date

No evidence that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC as specified in the requirement. Inspection and certification documents are described, but transmission and traceability to TechnipFMC a...

Open

920

10.2

AI

No

add date

Material certificate is issued according to EN 10204 Type 3.1 and order references ASTM A790 and NORSOK, indicating required information will be included. Source: 14-03 - Certification Montbard plant.doc

Open

921

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for required transverse testing. Source: DM...

Open

922

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

923

10.2

AI

No

add date

None of the provided documents include the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or test results as...

Open

924

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all relevant chemical, mechanical, manufacturing, and testing requirements. M-650 qualification is confirmed for the required wall thickness. Source...

Open

925

1.0

AI

No

add date

Supplier is M-650 accredited for UNS S32760 / DMV25.7N but not accredited to ISO 17782 as required; no evidence of full qualification or availability of QTR/MPCR documentation for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev...

Open

926

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

927

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

928

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed by heat analysis with supplier certification for DMV material. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM ...

Open

929

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

930

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

931

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, fulfilling the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed ...

Open

932

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per NORSOK MDS D51/ASTM A79...

Open

933

4.2

AI

No

add date

Tensile and hardness testing are performed in accordance with ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

934

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

935

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness required for standard transverse specimens. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - D...

Open

936

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PREN ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

937

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is explicitly required and matches the specification requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

938

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

939

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

940

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, actual magnification and scale bar reported if intermetallic phases are not detected, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

941

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

942

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not meet the stricter client requirement of no intermetallic phases and/or precipitates when CVN testing cannot ...

Open

943

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

944

4.4.3

AI

No

add date

Micrographic examination per ISO 17781 is specified, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impact ...

Open

945

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

946

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

947

4.5

AI

No

add date

DMV 25.7N complies with all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive, micrographic, corrosion tests, ferrite content, heat treatment, and manufacturing process requirements; plant is M-650 accredited for this ...

Open

948

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

949

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source: DM...

Open

950

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is confirmed, applicable after all mechanical processing, and covers the specified pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-...

Open

951

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

952

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT) is detailed, but there is no explicit confirmation of compliance with NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782 requirements. For the requested OD (219.1 mm), eddy current testing is not feasible, ...

Open

953

5.2

AI

No

add date

No provided document confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that the required NDE with these acceptance criteria can be performed for the specified pipe size and process ...

Open

954

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specifications from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a A...

Open

955

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

956

8.0

AI

No

add date

Marking per ASTM A790 §14 and Montbard standard practices includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

957

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

958

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

959

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

960

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demons...

Open

961

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03...

Open

962

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided as standard and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 -...

Open

963

10.2

AI

No

add date

Some documents confirm that EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 identification, melting practice, heat number, chemical analysis, solution annealing, and test results, but only the country of origin of the steel supplier is ...

Open

964

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all referenced mechanical, chemical, and testing requirements. Manufacturing is M-650 qualified for DMV 25.7N up to the required wall thickness. Sourc...

Open

965

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence provided for QTR/MPCR availability for review or full compliance with both standards. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06....

Open

966

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

967

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

968

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with frequency and method matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

969

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests, with specified locations and directions, is...

Open

970

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

971

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

972

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact ...

Open

973

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C, including minimum absorbed energy values and sub-size reduction factors. The specified pipe dimensions allow for both longitudinal and transverse Charpy V-notch test...

Open

974

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

975

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

976

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

977

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

978

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report at actual magnification and with a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

979

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

980

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

981

4.4.3

AI

No

add date

Ferrite content is determined per ASTM E 562 or by image analysis according to ASTM E 1245, performed in accordance with ISO 17781, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Diges...

Open

982

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching methods, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance is based on imp...

Open

983

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

984

4.5

AI

No

add date

No explicit confirmation of ASTM G48 Method 'A' (50°C, 24h) corrosion testing in accordance with ISO 17781 is provided for the requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

985

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 (ASTM A790, NORSOK M-650/ISO 17782) are fully addressed and DMV 25.7N is confirmed compliant for all relevant destructive and microstructural tests (tensile, impact, corrosion,...

Open

986

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

987

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

988

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, performed after all mechanical processing, meeting the requirement for 100% longitudinal defect detection. Source: DMV_STANDARD_BOOK/12 -...

Open

989

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed; only ASTM A790/A999 NDE is detailed. For the specified OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only avail...

Open

990

5.2

AI

No

add date

No provided document explicitly states that any indication greater than the calibration notch is considered a defect requiring rejection or repair, and standard NDE methods are not feasible for the requested OD at Montbard, so the requirement cannot ...

Open

991

6.0

AI

No

add date

Dimensional tolerances are confirmed as per the applicable ASTM standard (ASTM A790/A999) for the specified pipe size, with no overriding customer specification or drawing indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STAN...

Open

992

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

993

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

994

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in the specification for DMV 25.7N seamless pipe under NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-0...

Open

995

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

996

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

997

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification dem...

Open

998

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

999

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and will include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control as per specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_...

Open

1000

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all required metallur...

Open

1001

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all referenced mechanical, chemical, and testing requirements. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_...

Open

1002

1.0

AI

No

add date

Supplier is M-650 accredited for DMV25.7N but not accredited to ISO 17782 as required; no evidence of QTR/MPCR documentation availability or full compliance with NORSOK M-650/ISO 17782 qualification for the exact product supplied. Source: DMV_STANDAR...

Open

1003

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

1004

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1005

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN ≥ 40 as required by Table 2 and NORSOK MDS D51 Rev 06. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

1006

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and furnace qualification and free circulation of media are covered by these standards. Source: DMV_S...

Open

1007

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with lot defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

1008

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

1009

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) meets requirements: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, with pipe dimensi...

Open

1010

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

1011

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW, fulfilling all Table 4 mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

1012

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfills the requirement as the pipe wall thickness exceeds the minimum required for testing per ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Imp...

Open

1013

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact test requirements at -46°C: minimum 45/35 J (transverse) and 65/50 J (longitudinal if transverse not possible) for thickness ≥6 mm. The specified pipe dimensions allow for required testing directio...

Open

1014

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

1015

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, is required for micrographic examination as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

1016

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

1017

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

1018

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with representative micrographs at or near mid-wall thickness, actual magnification, and a scale bar included if intermetallic phases are not detected. Source: DMV_STANDARD_BOO...

Open

1019

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

1020

4.4.2

AI

No

add date

The available specifications allow isolated intermetallic precipitates below 10µm and do not fully prohibit intermetallic phases/precipitates when CVN testing cannot be completed, as required by the client specification. No evidence of a stricter pro...

Open

1021

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

1022

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

1023

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% and DMV 25.7N complies per ISO 17781 and ASTM E1245. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06....

Open

1024

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or documented. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1025

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spe...

Open

1026

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02...

Open

1027

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

1028

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

1029

5.2

AI

No

add date

No evidence that NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782 are addressed. Standard NDE methods (EC, UT, hydrostatic) for the specified OD are only available at extra cost or require technical consultation, and f...

Open

1030

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair; NDE acceptance criteria and feasibility for the specified dimension are not confirmed for Montbard plant operations or ...

Open

1031

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790) unless otherwise specified, and no deviations are stated in the customer specification or context. Source: DMV_STANDARD_BOOK/07-01 - General informatio...

Open

1032

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1033

8.0

AI

No

add date

Marking per ASTM A790 includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Marking methods (indelible black ink, vibro-etching) are standard and meet the requirement. Source: DMV_STANDARD_BOOK/02-04-03 -...

Open

1034

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 -...

Open

1035

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA and specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

1036

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

1037

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

1038

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

1039

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary or QTR...

Open

1040

10.2

AI

No

add date

No provided documents contain all required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or actu...

Open

1041

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification digest and the customer specification listing 'A790 NORSOK'. M-650 qualification is also met for the required ...

Open

1042

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR documentation availability or full compliance with both NORSOK M-650/ISO 17782 as required by the specification. Sou...

Open

1043

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

1044

3.1

AI

No

add date

AOD or equivalent refining is used and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

1045

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790 as required, with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 7...

Open

1046

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

1047

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for one set per heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

1048

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

1049

4.1

AI

No

add date

Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, are fulfilled for DMV 25.7N. The...

Open

1050

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

1051

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 and ASTM A790 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

1052

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions (18.26mm WT, 219.1mm OD) in both longitudinal and transverse directions as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - D...

Open

1053

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, including minimum absorbed energy values and sub-size specimen reduction factors. The specified pipe dimensions allow for both longitudinal and transverse Charpy V-n...

Open

1054

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

1055

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution for detecting ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

1056

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

1057

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs are included as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

1058

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

1059

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

1060

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10 µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Zero-tolerance is not confirmed for this case. Source: DMV_STANDARD_BO...

Open

1061

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

1062

4.4.3

AI

No

add date

Micrographic examination is performed as per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Acceptance criteria: structure is basically free from intermetallic precipitates (isolated, non-distrib...

Open

1063

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% and DMV 25.7N complies per ISO 17781 and ASTM E1245. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06....

Open

1064

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or confirmed in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1065

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, with compliance confirmed by test results. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

1066

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02...

Open

1067

5.1

AI

No

add date

No information is provided regarding the qualification, certification, or defined roles and responsibilities of NDE personnel to ISO 9712 level II or III or equivalent. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montb...

Open

1068

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is performed after all mechanical processing, heat treatments, and straightening, and the equipment supports the specified pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testin...

Open

1069

5.2

AI

No

add date

NDE requirements per ASTM A790 and NORSOK M-630/MDS D51 are not fully addressed; eddy current testing is not feasible for the required OD, and there is no explicit confirmation of alternative NDE methods or full-length dye penetrant testing for the s...

Open

1070

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor that such NDE acceptance criteria are standardly performed or feasible for the specified pipe di...

Open

1071

6.0

AI

No

add date

Dimensional tolerances are specified as per the applicable ASTM standard (ASTM A790 and referenced ASTM A999) for the requested product dimensions, with no deviations or overrides stated by TechnipFMC, fulfilling the requirement. Source: DMV_STANDARD...

Open

1072

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

1073

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-0...

Open

1074

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' (§ 13, § 14) for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORS...

Open

1075

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

1076

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

1077

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to 31.75 mm WT (requested: 18.26 mm), and the EN 10204 type 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number for the ...

Open

1078

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dige...

Open

1079

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control for mill inspection and referencing the relevant standards and manufacturing details as specified. Source: DM...

Open

1080

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching by 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

1081

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, actual chemical analysis results, solution annealing parameters, and results of all meta...

Open

1082

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, with M-650 qualification for the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Di...

Open

1083

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence provided for full qualification to NORSOK M-650/ISO 17782 or availability of QTR/MPCR for review as required by the specificatio...

Open

1084

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

1085

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1086

3.1

AI

No

add date

UNS S32760 chemical composition matches Table 2 requirements and is confirmed by supplier certification and heat analysis per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-...

Open

1087

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

1088

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with lot defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

1089

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

1090

4.1

AI

No

add date

Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, are fulfilled for DMV 25.7N per ...

Open

1091

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

1092

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 06 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

1093

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness required for standard transverse specimens. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - D...

Open

1094

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C (transverse: 45/35 J, longitudinal: 65/50 J, reduction factors for sub-size specimens specified). The requested pipe dimensions allow for required Charpy V-notch test...

Open

1095

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants and electrolytic etching after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02...

Open

1096

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is explicitly required for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

1097

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

1098

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

1099

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

1100

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

1101

4.4.2

AI

No

add date

No evidence that intermetallic phases and/or precipitates are completely prohibited when CVN testing cannot be completed; existing specifications allow isolated precipitates below 10μm, which does not meet the stricter client requirement. Source: DMV...

Open

1102

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

1103

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

1104

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, meeting the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

1105

4.5

AI

No

add date

ASTM G48 Method 'A' corrosion testing at 50°C for 24h in accordance with ISO 17781 is not explicitly mentioned or referenced, so compliance cannot be confirmed. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1106

4.5

AI

No

add date

All acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 06 are fulfilled for DMV 25.7N, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

1107

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

1108

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

1109

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 or ISO 10893-10 is confirmed, performed after all processing, and the dimensional range is supported. Reference notches are prepared as per ASTM E213 standard practice. Sou...

Open

1110

5.2

AI

No

add date

100% hydrostatic or NDE (EC or UT) testing per ASTM A999/ASTM A790 is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE acceptance criteria are addressed. For the requested OD (219.1 mm), eddy ...

Open

1111

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor that the required NDE acceptance criteria are met for the specified product and...

Open

1112

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no evidence of override in the customer specification or part report/drawing. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DM...

Open

1113

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1114

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

1115

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

1116

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

1117

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

1118

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

1119

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products being delivered as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dige...

Open

1120

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference. Source: DMV_STANDARD_BO...

Open

1121

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -46°C (≥45 J average, 35 J single transverse; ≥65 J average, 50 J single longitudinal if transverse not possible) for thickness ≥6 mm. The specified pipe dimensions allow for both t...

Open

1122

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

1123

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

1124

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all required metallurgic...

Open

1125

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51...

Open

1126

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability or full compliance with both NORSOK M-650/ISO 17782 as required. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

1127

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

1128

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06....

Open

1129

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN ≥ 40, matching the requirements of Table 2 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1130

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnace qualification per NORSOK M-650/ISO 17782. Free circulation of heating and cooling media is ensured by compliance with these standards. S...

Open

1131

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

1132

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, directly referencing the required table for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

1133

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified lo...

Open

1134

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

1135

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

1136

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfills the requirement as the pipe wall thickness exceeds the minimum required for testing per ASTM A370 and ISO 148-1 (striker radius 8 mm). Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive ...

Open

1137

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

1138

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

1139

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report at actual magnification and with a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/...

Open

1140

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK/0...

Open

1141

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates below 10μm, which does not meet the stricter client requirement of no interm...

Open

1142

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

1143

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

1144

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

1145

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1146

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements based on destructive and micrographic tests. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NO...

Open

1147

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

1148

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source: DM...

Open

1149

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

1150

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51 are not fully addressed; only standard ASTM A790/A999 NDE is confirmed, and plant feasibility for required NDE methods (eddy current, hydrostatic, ultrasonic, full-length dye penetrant) f...

Open

1151

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782; no evidence provided for QTR/MPCR availability or full compliance with both standards as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1152

5.2

AI

No

add date

No explicit confirmation that NDE acceptance criteria require rejection or repair of indications greater than the calibration notch; NDE feasibility for the requested OD is not confirmed as standard or may incur extra cost; specific acceptance criter...

Open

1153

6.0

AI

No

add date

Dimensional tolerances are confirmed as per the applicable ASTM standard (ASTM A999 referenced by ASTM A790) for the requested dimensions, with no override by TechnipFMC indicated in the provided context. Source: DMV_STANDARD_BOOK/07-01 - General inf...

Open

1154

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

1155

8.0

AI

No

add date

Marking is performed according to ASTM A790 (§14) and includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-...

Open

1156

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1157

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

1158

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

1159

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

1160

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

1161

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - ...

Open

1162

10.2

AI

No

add date

EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 identification, steel melting practice and refining method, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer....

Open

1163

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all standard, supplementary, and testing requirements. M-650 qualification is confirmed for the required wall thickness. Source: DMV_STANDARD_BOOK/...

Open

1164

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

1165

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

1166

3.1

AI

No

add date

Chemical composition for UNS S32760 conforms to Table 2 of ASTM A790, matching the specified requirements, with heat analysis and supplier certification provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

1167

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

1168

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

1169

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/...

Open

1170

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), corrosion, and microstructure at specified thickness locations, is fulfilled per NORSOK MDS D51/ASTM A790. F...

Open

1171

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 as required for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

1172

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

1173

4.3

AI

No

add date

Pipe wall thickness exceeds the minimum required for Charpy V-notch testing per ASTM A370 and ISO 148-1, making testing feasible and fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Imp...

Open

1174

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -46°C, with minimum absorbed energy values for both transverse and longitudinal directions, and the specified pipe dimensions allow for required testing orientation and specimen siz...

Open

1175

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

1176

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination and fulfills the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

1177

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

1178

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

1179

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

1180

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

1181

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

1182

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

1183

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

1184

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Structure must be basically free from intermetallic precipitates, with isolated precipitates allowed if ...

Open

1185

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

1186

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is fulfilled or referenced in the provided documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1187

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORS...

Open

1188

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

1189

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

1190

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available and applicable for the specified pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultrasonic testing...

Open

1191

5.2

AI

No

add date

100% hydrostatic or NDE (EC or UT) testing per ASTM A999/ASTM A790 is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD (219.1 mm), eddy current...

Open

1192

5.2

AI

No

add date

No provided documentation explicitly confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor that such NDE acceptance criteria are standardly applied or feasible for t...

Open

1193

6.0

AI

No

add date

Dimensional tolerances are specified as per the applicable ASTM standard (ASTM A790/A999) for the relevant pipe size, with no overriding TechnipFMC specification indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/...

Open

1194

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

1195

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

1196

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

1197

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

1198

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

1199

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

1200

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, and the QTR number is included as per M-650 qualification, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/...

Open

1201

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products being delivered as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

1202

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

1203

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive te...

Open

1204

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are manufactured and tested in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, meeting all relevant mechanical, chemical, and testing specifications for 25 Cr Dup...

Open

1205

1.0

AI

No

add date

No evidence of supplier qualification to NORSOK M-650/ISO 17782 for the exact product supplied or availability of Qualification Test Record/MPCR for review. One source confirms NORSOK M-650 accreditation but not ISO 17782, which is required by the sp...

Open

1206

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm for hot finished, 10.925 mm for cold finished), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 require...

Open

1207

3.1

AI

No

add date

AOD or equivalent refining is used 100% for DMV 25.7N, and the chemical composition complies with Table 2 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Diges...

Open

1208

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the inquiry WT is 18.26 mm, within the accredited range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

1209

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed per ASTM A790, with manufacturing process and furnaces qualified according to NORSOK M-650 (or ISO 17782), ensuring compliance with requirements including free circulati...

Open

1210

4.1

AI

No

add date

No evidence is provided that impact, tensile, hardness, corrosion testing, and microstructure examinations are performed for each heat and heat treatment lot as defined in ASTM A790. Testing frequency, lot definition, and compliance with the full set...

Open

1211

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

1212

4.1

AI

No

add date

Test sampling requirements for tensile and CVN tests, including test direction and thickness location, as well as requirements for microstructure and corrosion sampling, are not fully addressed. There is no confirmation of CVN impact testing or full ...

Open

1213

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4. Hardness testing is performed and results are provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

1214

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required in Table 4 are not provided or confirmed for DMV 25.7N in the available documents. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - De...

Open

1215

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, meeting the minimum wall thickness requirements for both standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testi...

Open

1216

4.3

AI

No

add date

Pipe dimensions allow standard Charpy V-notch impact testing; impact property requirements in Table 5 can be fulfilled. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

1217

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination according to ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - ...

Open

1218

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination of ferrite balance and intermetallic phases is provided or addressed in the reviewed documents. Source: DMV_STANDA...

Open

1219

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

1220

4.4.2

AI

No

add date

No evidence of recording the presence and location of intermetallic phases with micrographs at 400x magnification; only grain size measurement is addressed or no relevant information provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - De...

Open

1221

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at 400x minimum magnification with actual magnification and scale bar when intermetallic phases are not detected. Grain size and general micrographic ...

Open

1222

4.4.2

AI

No

add date

No evidence of reporting centerline intermetallic stringers or acceptance criteria based on CVN and corrosion test results is provided in the relevant documents. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I.doc, DMV_STANDARD_B...

Open

1223

4.4.2

AI

No

add date

NORSOK MDS D41 Rev 06 and D51 Rev 06 allow isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed. Th...

Open

1224

4.4.3

AI

No

add date

No information is provided confirming ferrite content determination per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781; only grain size measurement is discussed, not ferrite content analysis or the specified standards. Source: DMV_STANDARD_BO...

Open

1225

4.4.3

AI

No

add date

No acceptance criteria for micrographic examination or metallurgical properties are specified for DMV 25.7N in the provided sources; only procedures and general information are given without specific requirements or results relevant to the inquiry. S...

Open

1226

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1227

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1228

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are provided in the requirement or referenced documents, making validation impossible with the given information. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_B...

Open

1229

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² matches the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

1230

5.1

AI

No

add date

No evidence provided regarding qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDARD_BOOK...

Open

1231

5.2

AI

No

add date

Only confirmation that pipe dimensions are within ultrasonic testing capability; no evidence that testing is performed after all processing or that calibration notches meet ASTM E213 Figure 3 requirements. Source: DMV_STANDARD_BOOK/12 - Special Testi...

Open

1232

5.2

AI

No

add date

Dye penetrant testing is available for tube ends and bevels on request, and 100% qualitative anti-mixing PMI is performed on standard production, fulfilling the NDE acceptance criteria for the Montbard plant. Source: DMV_STANDARD_BOOK/12-02-05 - Dye ...

Open

1233

5.2

AI

No

add date

No provided document confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor is there confirmation that the required NDE with calibration notch reference is standardly performed or fea...

Open

1234

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for both hot and cold finished products are confirmed as per the applicable ASTM standards (including ASTM A 790 with A 999 for tolerances), with no overriding TechnipFMC part report or drawing reference...

Open

1235

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and white pickled or bright annealed per NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790, NORS...

Open

1236

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

1237

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required for MST-Tubes in the referenced specification digest. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

1238

10.0

AI

No

add date

No evidence is provided that the Montbard plant has an ISO 9001 (or equivalent) quality-assurance system certified by a competent EEA body or that it has undergone a specific assessment for materials. Certification details are referenced but not incl...

Open

1239

10.1

AI

No

add date

No confirmation that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification or that documentation will be submitted to TechnipFMC for approval. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14...

Open

1240

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the relevant wall thickness, and QTR number is included as per M-650 qualification, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MCPR f...

Open

1241

10.2

AI

No

add date

No evidence that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC as specified in the requirement. No explicit statement of compliance found in the relevant documents. Source: DMV_STANDARD_BOOK/14-01 - ...

Open

1242

10.2

AI

No

add date

Material certificate is issued according to EN 10204 Type 3.1 and validated by Quality Control; reference to DMV 25.7N and NORSOK in the order metadata implies inclusion of information required by ASTM A790 and NORSOK M-630. Source: 14-03 - Certifica...

Open

1243

10.2

AI

No

add date

No provided documentation includes NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or results of required metallurgical and non-destructive testing for the delivered...

Open

1244

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02-03-01 - Digest AST...

Open

1245

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS...

Open

1246

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, with manufacturing process qualified per NORSOK M-650 or ISO 17782, and compliance with NORSOK M-630 MDS D51 Rev. 6 is referenced. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

1247

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1248

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

1249

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

1250

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

1251

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

1252

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, directly referencing the required table for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

1253

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure, with specified locations and directions, is fulfilled. For the requested pipe ...

Open

1254

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

1255

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

1256

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness requirements for transverse specimens. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destru...

Open

1257

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -466C: minimum 45/35 J (transverse) and 65/50 J (longitudinal) for thickness >6mm. The specified pipe dimensions allow for required transverse and longitudinal Charpy V-notch testi...

Open

1258

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants and electrolytic etching after final polishing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

1259

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect intermetallic phases, in accordance with ISO 17781, is explicitly required for micrographic examination, fulfilling the requirement for suitable etchants as listed in ISO 17781 Appendix B to show ferrite bal...

Open

1260

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

1261

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

1262

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

1263

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

1264

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully fulfilled. Source: DMV_STA...

Open

1265

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

1266

4.4.3

AI

No

add date

Microstructure examination is performed as per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at a minimum 400X magnification. Acceptance criteria: structure must be basically free from intermetallic precipitates (isola...

Open

1267

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

1268

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1269

4.5

AI

No

add date

DMV 25.7N fulfills ASTM A790 and NORSOK MDS D51 Rev 6 acceptance criteria for metallurgical properties, including all relevant destructive and micrographic tests, and is M-650 qualified up to the specified wall thickness. Source: 02-02-01 Digest summ...

Open

1270

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

1271

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712 or equivalent. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive t...

Open

1272

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects is performed in accordance with ASTM E213 and ISO 10893-10 for the specified pipe dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/1...

Open

1273

5.2

AI

No

add date

NDE as per ASTM A790 is confirmed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. Standard NDE methods (eddy current, ultrasonic, hydrostatic) are not fully feasibl...

Open

1274

5.2

AI

No

add date

No provided document confirms that indications greater than the calibration notch are classified as defects requiring rejection or repair, nor that NDE with this acceptance criterion is standard for the specified pipe dimension at Montbard. Source: D...

Open

1275

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790 referencing ASTM A999) for the specified pipe dimensions, with no deviations or special tolerance requests indicated by the customer specification or TechnipFMC part report/drawin...

Open

1276

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 (6.1.3) and white pickled or bright annealed per NORSOK MDS D51 (§13), directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: D...

Open

1277

8.0

AI

No

add date

Marking is per ASTM A790 §16, requiring full traceability to melt and heat treatment lot, and includes mandatory marking of heat number and DMV lot number, ensuring compliance with the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK M...

Open

1278

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

1279

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

1280

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability is provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1281

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the requirement for qualification for the s...

Open

1282

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

1283

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 manufacturing summary/QTR number. ...

Open

1284

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. No evidence is ...

Open

1285

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by specification digests and the client inquiry listing 'A790 NORSOK' in the relevant standards column. All mechanical, chemical...

Open

1286

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of availability of QTR/MPCR documentation for review by TechnipFMC as required by the specification. MST-Tubes is NORSOK M-650 a...

Open

1287

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm for hot finished, 10.925 mm for cold finished), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirem...

Open

1288

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N complies with the chemical composition requirements per Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

1289

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the requested product (WT = 18.26 mm). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

1290

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed in accordance with ASTM A790, the manufacturing process is qualified to NORSOK M-650/ISO 17782, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heat...

Open

1291

4.1

AI

No

add date

There is no explicit confirmation that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790. Required testing frequency and lot definition a...

Open

1292

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

1293

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no evidence of CVN impact testing or detailed test sampling (test direction, thickness location, or use of prolongation samples) as required by the specification. Source: DMV_STANDARD_BOOK/02-0...

Open

1294

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-...

Open

1295

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required for DMV 25.7N are not explicitly stated or confirmed in the provided documents. Referenced standards or values do not match the required grade or specificati...

Open

1296

4.3

AI

No

add date

No evidence that Charpy V-notch testing will be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1, or that results will meet Table 5 requirements, despite feasibility for the specified wall thickness being confirmed. Source: DMV_STANDA...

Open

1297

4.3

AI

No

add date

Impact testing at -46°C with specified absorbed energy values is feasible and can be fulfilled for the requested pipe dimensions (OD 219.1mm, WT 18.26mm), which exceed the minimum wall thickness required for both longitudinal and transverse specimens...

Open

1298

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination according to ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - ...

Open

1299

4.4.1

AI

No

add date

No evidence of the use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination is provided; relevant documents only address austenitic grain size measurement, not duplex/super-duplex etchin...

Open

1300

4.4.2

AI

No

add date

Micrographic examination requires the microstructure to be basically free from intermetallic phases, allowing isolated phases if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - S...

Open

1301

4.4.2

AI

No

add date

No evidence of recording the presence and location of intermetallic phases with micrographs at 400x magnification is provided or addressed in the relevant documentation or comments.

Open

1302

4.4.2

AI

No

add date

If intermetallic phases are not detected, a representative micrograph at or near mid-wall thickness is recorded at a minimum of 400x magnification, reported at actual magnification, and includes a scale bar. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

1303

4.4.2

AI

No

add date

No relevant documentation addresses the reporting of centerline intermetallic stringers or acceptance based on CVN and corrosion test results in relation to their presence. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I.doc, DMV...

Open

1304

4.4.2

AI

No

add date

Referenced specifications allow isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not meet the stricter client requirement that prohibits any intermetallic phases and/or precipitates if CVN testing ...

Open

1305

4.4.3

AI

No

add date

No provided documents address ferrite content determination or reference ASTM E 562, ASTM E 1245, or ISO 17781 as required for ferrite content measurement in duplex/super-duplex steels. Source: DMV_STANDARD_BOOK/12-03-03 - Micrographic Examination in...

Open

1306

4.4.3

AI

No

add date

No acceptance criteria for micrographic examination are specified or referenced in the provided documents for DMV 25.7N; only procedures and general standards are mentioned without required values or ranges for acceptance. Source: DMV_STANDARD_BOOK/0...

Open

1307

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1308

4.5

AI

No

add date

There is no evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 being performed or referenced in the provided documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1309

4.5

AI

No

add date

No explicit acceptance criteria for metallurgical properties are specified or detailed for DMV 25.7N in the provided information or referenced documents. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-0...

Open

1310

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² matches the requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

1311

5.1

AI

No

add date

No provided documents confirm that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_...

Open

1312

5.2

AI

No

add date

No explicit confirmation of 100% ultrasonic testing per ASTM E213 or ISO 10893-10, including reference notch requirements, after all processing steps is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03...

Open

1313

5.2

AI

No

add date

100% qualitative anti-mixing PMI check is performed on standard production at Montbard using appropriate instruments, fulfilling the general NDE requirement for positive material identification. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - ...

Open

1314

5.2

AI

No

add date

No provided document confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor is there confirmation that the required NDE is standard or feasible for the specified dimension at Montbard. A...

Open

1315

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed as per the applicable ASTM standards (including ASTM A790/A999) for the requested product dimensions, with no deviations or special requirements from TechnipFMC indicated. Requirement is fu...

Open

1316

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed (ASTM A790) and white pickled or bright annealed (NORSOK MDS S01), directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790, NORSOK MDS S01.

Open

1317

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

1318

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

1319

10.0

AI

No

add date

No evidence of an ISO 9001 quality-assurance system or certification by a competent EEA body is provided for the Montbard plant or manufacturer. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Certification Montba...

Open

1320

10.1

AI

No

add date

No evidence provided of an ISO 9001 certified quality-assurance system by a competent EEA body or submission of required documentation for TechnipFMC approval as specified. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/...

Open

1321

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

1322

10.2

AI

No

add date

No explicit confirmation that documentation traceable to the products (SIR205) will be transmitted to TechnipFMC as required. Inspection and certification documents are mentioned, but traceability and transmission to TechnipFMC are not confirmed. Sou...

Open

1323

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

1324

10.2

AI

No

add date

Material certificate will be issued according to EN 10204 Type 3.1 and includes information required by ASTM A790 and NORSOK M-630. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/1...

Open

1325

10.2

AI

No

add date

None of the provided documents include the required documentation or certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details,...

Open

1326

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 Rev. 6. Compliance for DMV 25.7N is explicitly stated, including all relevant mechanical, chemical, and testing req...

Open

1327

1.0

AI

No

add date

Supplier is qualified according to NORSOK M-650/ISO 17782 as required for the product supplied. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D41 Rev 06....

Open

1328

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm for hot finished, 10.925 mm for cold finished), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 require...

Open

1329

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes and DMV 25.7N complies with the required chemical analysis. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORS...

Open

1330

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the requested product (WT = 18.26 mm). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

1331

3.2

AI

No

add date

Solution annealing with water quenching per ASTM A790 is standard for DMV 25.7N, with manufacturing process and furnaces qualified to NORSOK M-650, and pipes arranged for free circulation of heating/cooling media during heat treatment, fulfilling all...

Open

1332

4.1

AI

No

add date

No document confirms that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790; only partial or unrelated information is provided regarding ...

Open

1333

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

1334

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no information on CVN impact testing, test directions for CVN, or detailed sampling locations for CVN, corrosion, or microstructure as required by the specification table. Source: DMV_STANDARD_...

Open

1335

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

1336

4.2

AI

No

add date

No provided document contains mechanical property values for DMV 25.7N (UNS S32760) or demonstrates fulfillment of the tensile strength, yield strength, elongation, or hardness requirements specified in Table 4. Source: DMV_STANDARD_BOOK/02-03-01 - D...

Open

1337

4.3

AI

No

add date

No evidence that Charpy V-notch testing will be performed or that results will meet the requirements of Table 5, despite feasibility for the specified pipe dimensions being confirmed. Compliance with ASTM A370, ASTM A1058, or ISO 148-1 is not documen...

Open

1338

4.3

AI

No

add date

Impact testing at -46°C with specified absorbed energy values is feasible and can be fulfilled for pipe with 18.26mm wall thickness, as both ASTM and ISO rules confirm transverse specimens are possible for this size. Source: DMV_STANDARD_BOOK/12 - Sp...

Open

1339

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination to ISO 17781 or the specified etching solution for 25 Cr Duplex stainless steels; only grain size examination for austenitic materials is addressed, and duplex grades are...

Open

1340

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination; requirement not addressed for ferrite balance and intermetallic phases. Source: DMV_STANDARD_BOOK/12 - Special Te...

Open

1341

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic phases; isolated phases are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

1342

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided or addressed in the relevant documentation or comments. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/1...

Open

1343

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at 400x minimum magnification with a scale bar when intermetallic phases are not detected; partial mention of 400x photos but not all required details...

Open

1344

4.4.2

AI

No

add date

No provided documents address the presence, reporting, or acceptance criteria for centerline intermetallic stringers, nor do they link acceptance to CVN and corrosion test results in such cases. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examina...

Open

1345

4.4.2

AI

No

add date

Documents allow isolated intermetallic precipitates below 10µm and do not fully prohibit all intermetallic phases/precipitates if CVN testing cannot be completed, as required by the specification. No document fully addresses or fulfills the requireme...

Open

1346

4.4.3

AI

No

add date

No evidence of ferrite content determination by ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided. No relevant micrographic examination methods or results are mentioned. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destruct...

Open

1347

4.4.3

AI

No

add date

No provided document specifies acceptance criteria for micrographic examination or metallurgical properties relevant to section 4.4; requirements such as grain size, phase balance, or deleterious phases are not addressed for DMV 25.7N or the specific...

Open

1348

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1349

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) performed in accordance with ISO 17781 is provided in the available information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1350

4.5

AI

No

add date

No acceptance criteria for metallurgical properties are specified for DMV 25.7N or A790 NORSOK in the provided documents. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

1351

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria: no pitting at 20X magnification and weight loss < 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

1352

5.1

AI

No

add date

No provided documents contain information about NDE personnel qualification or certification to ISO 9712 level II or III, or their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_...

Open

1353

5.2

AI

No

add date

No confirmation of 100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10, nor reference notch details as specified. Dimensional feasibility only is addressed, not the testing method or calibration requirements. Source: DMV_ST...

Open

1354

5.2

AI

No

add date

100% qualitative anti-mixing PMI check is performed on standard production at Montbard using appropriate instruments, fulfilling the general NDE requirement for positive material identification. Source: DMV_STANDARD_BOOK/12-06-06 - Positive Material ...

Open

1355

5.2

AI

No

add date

No document confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor do they specify acceptance criteria or NDE feasibility for the requested size and standard. Source: DMV_STANDARD_BOOK/1...

Open

1356

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are applied per the applicable ASTM standards (including A 790 with A 999 for tolerances) for both hot and cold finished products, with no deviations or TechnipFMC overrides indicated for the specified d...

Open

1357

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and white pickled or bright annealed per NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790 diges...

Open

1358

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

1359

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated in the specification for MST-Tubes under NORSOK MDS S01 Rev 05. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest N...

Open

1360

10.0

AI

No

add date

No evidence is provided that the manufacturer has an ISO 9001 certified quality-assurance system by a competent EEA body with a specific assessment for materials. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Ce...

Open

1361

10.1

AI

No

add date

No confirmation that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification or that documentation will be submitted to TechnipFMC for approval. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14...

Open

1362

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, and the QTR number is included in the certificate, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MCPR for ...

Open

1363

10.2

AI

No

add date

No evidence that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC as specified in the requirement. No explicit mention of SIR205 or a process ensuring this traceability and transmission. Source: DMV_STA...

Open

1364

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 will be issued and validated by Quality Control for mill inspection, which fulfills the requirement for certification type and standard practice includes all relevant specification requirements fr...

Open

1365

4.4.2

AI

No

add date

No provided documents address the presence, reporting, or acceptance criteria for centerline intermetallic stringers, nor their relation to CVN or corrosion test results. Requirement not fulfilled.

Open

1366

10.2

AI

No

add date

None of the reviewed documents provide the required documentation or certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis results, solution annealing ...

Open

1367

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits in Table 2 and meets the PREN ≥ 40 requirement, as well as NORSOK MDS D51 Rev 06 and ASTM A790 standards. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51...

Open

1368

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

1369

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

1370

4.4.2

AI

No

add date

No document fully prohibits intermetallic phases and/or precipitates when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10µm, which does not meet the stricter client requirement of no intermetallics or prec...

Open

1371

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

1372

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed; standard NDE methods (EC, UT, hydrostatic) for the requested OD are only available at extra cost or require technical consultation, and fu...

Open

1373

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02...

Open

1374

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

1375

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demons...

Open

1376

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

1377

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, including heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing ...

Open

1378

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured and tested in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with all relevant mechanical, chemical, and testing requirements met. Source: 02-03-01 - Digest ...

Open

1379

10.2

AI

No

add date

No provided documentation includes NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution annealing parameters, or results of all required...

Open

1380

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of availability of QTR/MPCR documentation for review by TechnipFMC. MST-Tubes is only accredited to NORSOK M-650, not ISO 17782....

Open

1381

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, fulfilling the requirement for manufacturer and process qualification and meeting NORSOK ...

Open

1382

1.0

AI

No

add date

25 Cr Duplex stainless steel seamless pipes (DMV 25.7N) are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, as referenced in the inquiry metadata and confirmed by product digests. Manu...

Open

1383

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

1384

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Im...

Open

1385

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are reported with representative micrographs showing the location with the highest concentration of inter...

Open

1386

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 at ≥400X magnification, with etching to detect intermetallic phases, nitrides, and carbides. Structure must be basically free from intermetallic precipitates; isolated precipitates allowed if not ...

Open

1387

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

1388

9.0

AI

No

add date

Weld repairs are not acceptable per NORSOK MDS D51 Rev 06 (§ 13, § 14) for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1389

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

1390

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

1391

3.1

AI

No

add date

AOD or equivalent is used 100% for DMV 25.7N, and the chemical composition complies with Table 2 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

1392

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the inquiry's wall thickness of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

1393

3.2

AI

No

add date

Solution annealing with water quenching per ASTM A790 is standard, and manufacturing process and furnaces are qualified to NORSOK M-650, ensuring free circulation of heating/cooling media during heat treatment. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

1394

4.1

AI

No

add date

There is no evidence that impact, tensile, hardness, corrosion testing, and microstructure examinations are performed for each heat and heat treatment lot as defined in ASTM A790. Testing frequency, lot definition, and full compliance with the requir...

Open

1395

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no evidence of CVN impact testing, hardness, corrosion, or microstructure sampling as specified in the requirement. Test directions and thickness locations for all required tests are not fully ...

Open

1396

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature with criteria matching or exceeding Table 4 requirements, and hardness testing is also performed. Compliance with NORSOK MDS D51 and mechanical property requirements is demonstrated. Source: DM...

Open

1397

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required in Table 4 are not explicitly provided or confirmed for DMV 25.7N; compliance cannot be validated from the available information. Source: DMV_STANDARD_BOOK/0...

Open

1398

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness requirements for both ASTM and ISO standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 -...

Open

1399

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm), but not to ISO 17782; no evidence of QTR/MPCR availability. Requirement for qualification to both NORSOK M-650/ISO 17782 and documentation availability is not fu...

Open

1400

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and lot definition, directly matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

1401

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements, including Charpy V-notch testing at -46°C with specified minimum absorbed energy values for both transverse and longitudinal directions, and the pipe dimensions allow for required test...

Open

1402

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

1403

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1404

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled; only ASTM A790/A999 NDE is detailed, and Montbard plant feasibility for required NDE methods (eddy current, hydrostatic, ultrasonic, full-leng...

Open

1405

4.3

AI

No

add date

Pipe with OD 219.1 mm and WT 18.26 mm (>6 mm) allows both longitudinal and transverse Charpy V-notch impact testing at -46°C with required absorbed energies, fulfilling the requirement. Source: 12-03-02 - Impact Test for hot finished products.doc

Open

1406

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination per ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels; only grain size measurement for austenitic materials is discussed, and duplex steels ...

Open

1407

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant as per ISO 17781 Appendix B for micrographic examination to show ferrite balance and intermetallic phases in the provided documentation.

Open

1408

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic phases; isolated phases are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

1409

4.4.2

AI

No

add date

No evidence of recording the presence and location of intermetallic phases with micrographs at 400x magnification is provided or addressed in the relevant documentation or comments. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive t...

Open

1410

4.4.2

AI

No

add date

If intermetallic phases are not detected, a representative micrograph at minimum 400x magnification at or near mid-wall thickness is recorded, reported at actual magnification, and includes a scale bar. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

1411

4.4.2

AI

No

add date

Referenced documents allow isolated intermetallic precipitates below 10µm and do not fully prohibit intermetallic phases/precipitates if CVN testing cannot be completed, as required by the specification. No document fully fulfills the prohibition req...

Open

1412

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided; only grain size measurement is addressed, not ferrite content determination by the specified methods or standards. Source: DMV_STANDARD...

Open

1413

4.4.3

AI

No

add date

No acceptance criteria for micrographic examination are specified or fulfilled in the provided documents; relevant documents only describe procedures or general requirements without specific criteria for DMV 25.7N or the inquiry at hand. Source: DMV_...

Open

1414

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1415

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided; only 'A790 NORSOK' is referenced, which does not confirm fulfillment of this requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tes...

Open

1416

4.5

AI

No

add date

No acceptance criteria for metallurgical properties are specified for DMV 25.7N or A790 NORSOK; relevant sections are missing or not addressed for the required grade and standard. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STAND...

Open

1417

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is specified, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

1418

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDA...

Open

1419

5.2

AI

No

add date

No confirmation that 100% ultrasonic testing for longitudinal defects will be performed according to ASTM E213 or ISO 10893-10, nor evidence regarding reference notches or test timing after all processing. Source: DMV_STANDARD_BOOK/12 - Special Testi...

Open

1420

7.0

AI

No

add date

Both ASTM A790 and NORSOK MDS S01 require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: ASTM A790 digest, NORSOK MDS S01 Rev 05

Open

1421

5.2

AI

No

add date

100% qualitative anti-mixing PMI check is performed on standard production at Montbard using appropriate instruments, fulfilling the general NDE requirement for positive material identification. Source: DMV_STANDARD_BOOK/12-06-06 - Positive Material ...

Open

1422

5.2

AI

No

add date

No provided document confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor is there confirmation that the required NDE is standardly performed or feasible for the specified pipe dimensi...

Open

1423

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed as per the applicable ASTM standards (A790/A999, A213/A1016, A268, A269, A312, A376, A511) for the requested product sizes, with no deviations or special instructions noted for this item. R...

Open

1424

8.0

AI

No

add date

Marking includes heat number and DMV lot number using indelible black ink and vibro-etching, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

1425

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS S01 Rev 05 for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 ....

Open

1426

10.0

AI

No

add date

No evidence is provided confirming the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body with a specific assessment for materials. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-0...

Open

1427

10.1

AI

No

add date

No confirmation that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification or that documentation will be submitted to TechnipFMC for approval. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14...

Open

1428

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, and the QTR number is included as per M-650 qualification, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/M...

Open

1429

10.2

AI

No

add date

No evidence that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC as specified in the requirement. No explicit mention of SIR205 or traceability to TechnipFMC is provided in the relevant documents. Sour...

Open

1430

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 will be issued and validated by Quality Control, with reference to ASTM A790 and NORSOK M-630 in the order specification indicating inclusion of required information. Source: 14-03 - Certification...

Open

1431

10.2

AI

No

add date

No provided document contains the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or test results for meta...

Open

1432

1.0

AI

No

add date

DMV 25.7N seamless pipes are specified as compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification confirmed for the required wall thickness. All relevant mechanical, chemical, and testing requirements are met for 25 Cr Dupl...

Open

1433

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N (UNS S32760) up to certain wall thicknesses but is not accredited to ISO 17782, as explicitly stated. No evidence provided for QTR/MPCR availability for review as required by the specification. Req...

Open

1434

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

1435

3.1

AI

No

add date

Chemical composition for UNS S32760 conforms to Table 2 of ASTM A790, matching the specified limits, with heat analysis and supplier certification provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-0...

Open

1436

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

1437

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

1438

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

1439

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations, fulfilling NORSOK MDS D51/...

Open

1440

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and the material meets the required tensile and maximum hardness properties of Table 4 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

1441

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

1442

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness required for testing. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-...

Open

1443

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements (Charpy V-notch at -46°C: transverse 45J/35J, longitudinal 65J/50J, with reduction factors for sub-size specimens), and the specified pipe dimensions allow for required testin...

Open

1444

4.4.1

AI

No

add date

ISO 17781 is referenced for micrographic examination and ferrite check, but the required specific etchant solution and procedure after final polishing are not explicitly confirmed; only general etchants are mentioned, not the exact client-specified s...

Open

1445

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

1446

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

1447

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

1448

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness when intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

1449

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

1450

4.4.2

AI

No

add date

No provided document prohibits all intermetallic phases and/or precipitates when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10µm, which does not meet the stricter client requirement. Source: DMV_STANDARD...

Open

1451

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

1452

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impa...

Open

1453

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

1454

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1455

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, ferrite content, corrosion, impact, PRE, tensile, and microstructure requirements. Source: DMV_STANDARD_BOOK/...

Open

1456

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

1457

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

1458

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

1459

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled; only ASTM A790/A999 NDE is detailed. For the requested OD, eddy current and ultrasonic testing are only available at extra cost and require te...

Open

1460

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PREN ≥ 40, as required by ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1461

5.2

AI

No

add date

No provided documentation explicitly confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor that such NDE acceptance criteria are standardly applied or feasible for t...

Open

1462

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no deviations specified by the customer. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances...

Open

1463

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot, and standard marking methods (indelible ink, vibro-etching) include heat and lot numbers as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

1464

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required for DMV 25.7N seamless pipe under NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

1465

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

1466

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

1467

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling supplier qualification documentation requirem...

Open

1468

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

1469

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO177...

Open

1470

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all required metallurgic...

Open

1471

1.0

AI

No

add date

DMV 25.7N seamless pipe is specified, with compliance to ASTM A790 and NORSOK M-630 MDS D51 Rev. 6 confirmed, and M-650 qualification for DMV 25.7N up to the required wall thickness is met. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

1472

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

1473

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1474

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

1475

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for testing per heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

1476

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

1477

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled for DMV 25.7N per NORSOK MDS D5...

Open

1478

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

1479

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

1480

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in ...

Open

1481

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C, including minimum absorbed energy values for both transverse and longitudinal directions, and the specified pipe dimensions allow for required testing. Source: DMV_S...

Open

1482

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

1483

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

1484

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

1485

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

1486

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report at actual magnification and with a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

1487

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

1488

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

1489

4.4.2

AI

No

add date

The available specifications allow isolated intermetallic precipitates below 10µm, while the requirement prohibits all intermetallic phases and/or precipitates if CVN testing cannot be completed. The requirement is not fully fulfilled by the referenc...

Open

1490

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

1491

4.4.3

AI

No

add date

Microstructure examination per ISO 17781 is specified, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), matching the requirement. Sour...

Open

1492

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

1493

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1494

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive, micrographic, tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified per NORSOK M-650/ISO 17782. Source: DMV_STANDA...

Open

1495

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, meeting the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest...

Open

1496

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

1497

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 can be performed after all processing steps, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non ...

Open

1498

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD (219.1 mm), eddy current and ultrasonic testing are only availab...

Open

1499

5.2

AI

No

add date

No available documentation explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, and standard NDE methods for this requirement are not feasible as standard capability at Montb...

Open

1500

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790 referencing ASTM A999) for the specified pipe dimensions, with no deviations or special tolerance requests stated in the customer specification. Source: DMV_STANDA...

Open

1501

8.0

AI

No

add date

Marking is performed per ASTM A790 §14 and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

1502

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

1503

1.0

AI

No

add date

Supplier is M-650 accredited for UNS S32760 / DMV25.7N but not accredited to ISO 17782 as required; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1504

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

1505

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

1506

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

1507

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, are provided as required by SIR205 and section 10.0 of the specification. Source: DMV_STANDARD...

Open

1508

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference. Source: D...

Open

1509

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical...

Open

1510

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all referenced mechanical, chemical, and testing requirements. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_...

Open

1511

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N within the required wall thickness range, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_...

Open

1512

3.1

AI

No

add date

DMV 25.7N (UNS S32760) chemical composition matches the requirements of Table 2 and complies with ASTM A790 and NORSOK MDS D51 Rev 06, including PREN ≥ 40 and all specified element limits. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest ...

Open

1513

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

1514

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for testing per heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

1515

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling as outlined in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

1516

4.1

AI

No

add date

Tensile, hardness, CVN (transverse or longitudinal if not possible), corrosion, and microstructure tests on prolongation samples from seamless pipes are performed per ASTM A790 and NORSOK MDS D51, with test directions and sampling locations as specif...

Open

1517

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

1518

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets or exceeds the required minimum tensile strength (750 MPa), yield strength (550 MPa), elongation (25%), and maximum hardness (310 HBW) per NORSOK MDS D51 Rev 6 and ASTM A790 for S32760. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

1519

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfills the requirement as the pipe wall thickness exceeds the minimum required by ASTM and ISO standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-0...

Open

1520

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements, including Charpy V-notch testing at -466C with minimum absorbed energy values (transverse: 45 J average/35 J single, longitudinal: 65 J average/50 J single if transverse not possible...

Open

1521

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified electrolytic etchant after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

1522

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is explicitly required for micrographic examination and matches the client's requirement. Source: DMV_STANDARD_BOOK/02 -...

Open

1523

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

1524

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

1525

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

1526

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

1527

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

1528

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

1529

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

1530

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1531

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, with microstructure criteria referenced to ISO 17781. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

1532

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

1533

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

1534

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 can be performed on the specified pipe dimensions after all processing steps, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destru...

Open

1535

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not addressed. For OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at extra cost. Full-length dye penetrant t...

Open

1536

5.2

AI

No

add date

No explicit confirmation that NDE acceptance criteria require rejection or repair of indications greater than the calibration notch; standard NDE methods are not feasible or only available at extra cost for the specified OD, so the requirement is not...

Open

1537

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a A ...

Open

1538

8.0

AI

No

add date

Marking is performed according to ASTM A790 (§14) and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Diges...

Open

1539

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

1540

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

1541

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

1542

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for UNS S32760/DMV25.7N up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

1543

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 manufacturing summary or QTR number, are provided as required by SIR205 and section 10.0 of the specification. Source: DMV_STANDARD...

Open

1544

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications and documentation. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NO...

Open

1545

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis results, solution annealing parameters, and results of all metallurgic...

Open

1546

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification references and digest, including M-650 qualification for the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

1547

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N (up to certain wall thicknesses) but is not accredited to ISO 17782, as required. No evidence of QTR/MPCR availability is provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS ...

Open

1548

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N with the requested wall thickness, and the manufacturing process is qualified per NORSOK M-650/ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

1549

3.1

AI

No

add date

AOD or equivalent steel refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1550

3.1

AI

No

add date

DMV 25.7N (UNS S32760) chemical composition matches the requirement table and complies with PREN ≥ 40, as confirmed by both ASTM A790 and NORSOK MDS D51 Rev 6 digests. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06...

Open

1551

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing process qualified to NORSOK M-650/ISO 17782, and heat treatment process ensures free circulation of media around each pipe as re...

Open

1552

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

1553

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ...

Open

1554

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified locations and directions, is fulfilled for DMV 25.7N. For the orde...

Open

1555

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with tensile and hardness properties meeting NORSOK MDS D51 Table 4 requirements for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spec...

Open

1556

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

1557

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact ...

Open

1558

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal (if transverse not possible), inclu...

Open

1559

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

1560

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases is required, in accordance with ISO 17781 Appendix B, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

1561

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

1562

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases. Source: DMV_STANDARD_BOOK/02...

Open

1563

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected, fulfilling the requirem...

Open

1564

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement regarding centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

1565

4.4.2

AI

No

add date

The available specifications allow isolated intermetallic precipitates below 10 µm, but do not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed, as required by the client specification. Full absence of interm...

Open

1566

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

1567

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

1568

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

1569

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the listed standards or documents. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1570

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, and complies with NORSOK M-650/ISO 17782 qualification requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

1571

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

1572

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source: DMV_STAN...

Open

1573

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within machine capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - U...

Open

1574

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not demonstrated. Only ASTM A790/A999 NDE is confirmed, and required NDE methods (EC, UT) for the specified OD are either not feasible or only available at extra co...

Open

1575

5.2

AI

No

add date

The available documents do not explicitly confirm that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor do they confirm that the required NDE with this acceptance criterion w...

Open

1576

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no deviations specified by TechnipFMC. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BO...

Open

1577

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

1578

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specified thickness loc...

Open

1579

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, fulfilling the requirement. Source: DMV_STANDARD...

Open

1580

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

1581

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1582

5.2

AI

No

add date

No provided documentation explicitly confirms that any indication greater than the calibration notch is considered a defect, nor that such pipe/tubing is rejected or repaired as required. NDE acceptance criteria and related rejection/repair procedure...

Open

1583

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

1584

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications and documentation scope. Source: DMV_STANDARD_BOOK/02-04-03 - Dig...

Open

1585

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1586

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, with a frequency of 1/lot for each test type, fulfilling the requirement. Source: DMV_STAND...

Open

1587

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

1588

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

1589

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

1590

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1591

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

1592

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

1593

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, fulfilling the qualification requirement for the specified size and product f...

Open

1594

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

1595

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/...

Open

1596

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or full metallurgical and non-destruct...

Open

1597

1.0

AI

No

add date

DMV 25.7N seamless pipes are specified as compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification confirmed for the required wall thickness and all relevant mechanical, chemical, and testing requirements fulfilled. Source: ...

Open

1598

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

1599

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1600

3.1

AI

No

add date

DMV 25.7N (UNS S32760) chemical composition complies with Table 2 of ASTM A790 and NORSOK MDS D51 Rev 06, including PREN ≥ 40 and all specified element limits. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - ...

Open

1601

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

1602

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

1603

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, directly referencing Table 3 for test specimen sampling as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02...

Open

1604

4.1

AI

No

add date

Tensile, hardness, CVN (transverse, longitudinal if not possible), corrosion, and microstructure tests are performed on seamless pipes per ASTM A790 and NORSOK M-630 MDS D51, with correct test directions and thickness locations. For the specified pip...

Open

1605

4.2

AI

No

add date

Tensile testing is performed at room temperature per standard requirements, meeting Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%, and maximum hardness per Table 4. Testing is in accordance with ASTM A370 or ISO 6892-1, as required. Source: DMV_STANDARD_BOO...

Open

1606

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: minimum tensile strength 750 MPa, yield strength 550 MPa, elongation 25%, and maximum hardness 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

1607

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions (OD 219.1mm, WT 18.26mm), fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - I...

Open

1608

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energy values for both transverse and longitudinal directions, and the specified pipe dimensions allow for proper testing orientation and speci...

Open

1609

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

1610

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

1611

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

1612

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 is performed with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included with presence and location of intermetallic phases noted and recorded. Source: DMV_STANDA...

Open

1613

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

1614

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

1615

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. No evidence of stricter prohibition is provided in the oth...

Open

1616

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

1617

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

1618

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

1619

4.5

AI

No

add date

Applicable standards listed do not mention ASTM G48 or ISO 17781, and there is no explicit confirmation that the required corrosion testing will be performed as specified. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1620

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

1621

4.5

AI

No

add date

DMV 25.7N meets the corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours, with no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

1622

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to level II or III in accordance with ISO 9712 or equivalent, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non ...

Open

1623

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-...

Open

1624

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/650 are not fully addressed; only general hydrostatic or NDE per ASTM A999 is confirmed. For OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only a...

Open

1625

5.2

AI

No

add date

No explicit confirmation that NDE acceptance criteria require rejection or repair of pipes with indications greater than the calibration notch; feasibility of required NDE for OD 219.1 mm is not confirmed for Montbard plant. Source: DMV_STANDARD_BOOK...

Open

1626

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790 referencing ASTM A999) for the specified pipe dimensions, with no evidence of override in the customer specification or part report/drawing. Source: DMV_STANDARD_B...

Open

1627

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

1628

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

1629

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1630

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

1631

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system certified within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

1632

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification dem...

Open

1633

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

1634

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and validated, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 manufacturing summary/QTR number). Source: DM...

Open

1635

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis results, solution annealing parameters, and results of all metallurgic...

Open

1636

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all referenced mechanical, chemical, and testing requirements. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_...

Open

1637

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability or full compliance with both NORSOK M-650/ISO 17782 as required by the specification. Source: DMV_STAND...

Open

1638

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

1639

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1640

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN ≥ 40 as required by NORSOK MDS D51 Rev 06 and ASTM A790 standards. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-...

Open

1641

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

1642

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

1643

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

1644

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N according to NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev ...

Open

1645

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per NORSOK MDS D51 and ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, longitudinal if not possible), and corrosion/microstructure tests are performed at specified ...

Open

1646

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

1647

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

1648

4.3

AI

No

add date

Charpy V-notch testing in accordance with ASTM A370 and ISO 148-1 is feasible for the specified pipe dimensions and can be performed as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03...

Open

1649

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C: minimum 45/35 J (transverse) and 65/50 J (longitudinal) for thickness >6mm. The specified pipe dimensions allow both longitudinal and transverse impact testing as re...

Open

1650

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants and electrolytic etching after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/...

Open

1651

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is explicitly required and matches the specification requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

1652

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

1653

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

1654

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

1655

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

1656

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

1657

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

1658

4.4.3

AI

No

add date

Microstructure examination is performed as per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at minimum 400X magnification. Structure must be basically free from intermetallic precipitates, with isolated precipitates a...

Open

1659

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided; neither standard nor test is mentioned in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant...

Open

1660

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including chemical composition, PRE, tensile, impact, corrosion, microstructure, and ferrite content requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

1661

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

1662

5.1

AI

No

add date

No evidence provided regarding qualification or certification of NDE personnel to ISO 9712 level II or III, or their roles and responsibilities. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-01 - Non destructive...

Open

1663

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects is performed in accordance with ASTM E213 and ISO 10893-10 after all processing steps; pipe dimensions are within equipment capability; calibration notches are expected to follow ASTM E213 as the stand...

Open

1664

5.2

AI

No

add date

NDE per ASTM A790 is partially addressed (hydrostatic or NDE per ASTM A999), but there is no explicit evidence of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782. For the specified OD (219.1 mm), eddy current, hydrostatic, and ul...

Open

1665

5.2

AI

No

add date

The available documents do not explicitly confirm that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, and standard NDE methods for the specified dimension are either not feasib...

Open

1666

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and ASTM A999 as required, with no overriding specifications from TechnipFMC indicated. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Toleran...

Open

1667

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

1668

9.0

AI

No

add date

Weld repairs are explicitly stated as not acceptable under 'Surface finish / Repairs of defects' (§13, §14) for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 -...

Open

1669

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

1670

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

1671

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for UNS S32760/DMV25.7N up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

1672

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products being delivered as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

1673

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary or QTR...

Open

1674

10.2

AI

No

add date

No provided documentation contains the required specific data or evidence for NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution annea...

Open

1675

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all referenced mechanical, chemical, and testing requirements. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_...

Open

1676

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N (with wall thickness limitations), but not accredited to ISO 17782 as required. No confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS...

Open

1677

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

1678

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

1679

3.1

AI

No

add date

Chemical composition limits for UNS S32760 conform to Table 2 of ASTM A790 as required, and heat analysis is performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Dig...

Open

1680

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

1681

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with lot defined per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

1682

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with frequency and method matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

1683

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per NORSOK MDS D51/ASTM A7...

Open

1684

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

1685

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

1686

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and is performed in accordance with the standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impa...

Open

1687

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if transverse is not p...

Open

1688

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

1689

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is explicitly required and matches the specification requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

1690

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

1691

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

1692

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, reported at actual magnification and including a scale bar, if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - ...

Open

1693

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

1694

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates, which does not meet the stricter client requirement of not permitting any i...

Open

1695

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

1696

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impa...

Open

1697

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

1698

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50°C, 24h) in accordance with ISO 17781 is provided; neither standard nor test is mentioned in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant...

Open

1699

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1700

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

1701

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

1702

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 can be performed on the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ul...

Open

1703

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially met with 100% hydrostatic or electric testing, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. Eddy current testing is not...

Open

1704

5.2

AI

No

add date

None of the provided documents explicitly confirm that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair during NDE, nor do they confirm that such NDE methods are standard for the ...

Open

1705

6.0

AI

No

add date

Dimensional tolerances are applied per ASTM A790/A999 as required, with no overriding TechnipFMC specification indicated. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances acc...

Open

1706

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

1707

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

1708

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

1709

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

1710

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

1711

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

1712

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO 17782 manufacturing summary or QTR number, are provided as required for transmission to TechnipFMC and product traceability. Source: DMV...

Open

1713

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51...

Open

1714

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and...

Open

1715

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1716

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N but not to ISO 17782, as required. No confirmation of QTR/MPCR availability for review. Requirement not fully fulfilled for NORSOK M-650/ISO 17782 qualification and documentation acces...

Open

1717

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, with qualification testing meeting NORSOK M-630 MDS D51 rev. 6 requirements. Sour...

Open

1718

3.1

AI

No

add date

AOD or equivalent steel melt refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1719

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements; DMV material composition is stated to comply and heat analysis is performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

1720

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

1721

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for one set per heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

1722

4.1

AI

No

add date

Table 3 or its outlined test specimen sampling details are not included or described in the provided documents; references to Table 3 exist but do not fulfill the requirement for outlining the sampling method or content. Source: DMV_STANDARD_BOOK/02-...

Open

1723

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled for DMV 25.7N pipe...

Open

1724

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with material meeting the tensile and maximum hardness properties of Table 4 as required by NORSOK MDS D51. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

1725

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

1726

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfills the requirement as the pipe wall thickness exceeds the minimum required for testing per ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Imp...

Open

1727

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements (Charpy V-notch at -466C: transverse 45J/35J, longitudinal 65J/50J, with sub-size reduction factors), and the specified pipe dimensions allow for required testing directions a...

Open

1728

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH solution after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

1729

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

1730

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

1731

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

1732

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with representative micrographs at or near mid-wall thickness, actual magnification, and a scale bar included if intermetallic phases are not detected. Source: DMV_STANDARD_BOO...

Open

1733

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

1734

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. The requirement is not fully fulfilled by the available do...

Open

1735

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

1736

4.4.3

AI

No

add date

Microstructure examination per ISO 17781 is specified, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impac...

Open

1737

4.4.3

AI

No

add date

Ferrite content of 35% to 60% is required and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1738

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1739

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/...

Open

1740

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

1741

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

1742

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions and is performed after all mechanical processing, heat treatment, and straightening, fulfilling the requirement for 100% longitudinal defe...

Open

1743

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT) is confirmed, but compliance with specific NDE requirements of NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782 is not demonstrated. For the requested OD (219.1 mm), Eddy current testing is not feasible, ...

Open

1744

4.4.2

AI

No

add date

No evidence of recording the presence and location of intermetallic phases with micrographs at 400x magnification is provided or addressed in the relevant documentation or comments.

Open

1745

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor that such NDE acceptance criteria are standardly applied or feasible for the requested pipe size...

Open

1746

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790) unless otherwise specified, with no deviations or overrides indicated by TechnipFMC for this inquiry. Source: DMV_STANDARD_BOOK/07-01 - General informa...

Open

1747

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

1748

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-0...

Open

1749

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required for DMV 25.7N seamless pipe under NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

1750

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

1751

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

1752

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number as required, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness. QTR number is included in the certificate, f...

Open

1753

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

1754

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

1755

10.2

AI

No

add date

EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the actual steel producer name. No specific docu...

Open

1756

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all referenced mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

1757

1.0

AI

No

add date

Supplier is NORSOK M-650 accredited for UNS S32760 / DMV25.7N but not accredited to ISO 17782; full qualification to both NORSOK M-650 and ISO 17782 is not demonstrated, nor is the availability of QTR/MPCR documentation confirmed for review as requir...

Open

1758

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to 31.75 mm WT, and the requirement is for 18.26 mm WT. The manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements...

Open

1759

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

1760

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

1761

3.1

AI

No

add date

Chemical composition for S32760 matches Table 2 requirements and is confirmed by supplier certification and heat analysis per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-...

Open

1762

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

1763

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

1764

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

1765

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, in accordance with NORSOK MDS D51...

Open

1766

4.2

AI

No

add date

Tensile testing is performed at room temperature in accordance with ASTM A370 or ISO 6892-1, and the material meets the specified tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

1767

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

1768

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible and fulfilled for the specified pipe dimensions, as the wall thickness exceeds the minimum required for testing. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destruc...

Open

1769

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible), with testing on thickness >6 mm. Th...

Open

1770

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

1771

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

1772

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

1773

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

1774

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: Digest NORSOK MDS D51 Rev 06.docx

Open

1775

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

1776

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

1777

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fulfilled. Source: DMV_STANDARD_...

Open

1778

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

1779

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

1780

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

1781

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1782

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1783

4.5

AI

No

add date

Corrosion test per ISO 17781 G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is confirmed for DMV 25.7N; requirement is fulfilled. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

1784

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

1785

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 can be performed on the specified pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultrasonic testing/12-02-03 - ...

Open

1786

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no explicit evidence of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements. For the requested OD, eddy current testing is not feasible, and hydrostatic or ultras...

Open

1787

5.2

AI

No

add date

None of the relevant documents explicitly state that any indication greater than that produced by the calibration notch represents a defect, nor do they confirm that defective pipe and tubing shall be rejected or repaired according to this criterion....

Open

1788

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no deviations or special tolerances specified by TechnipFMC. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances ...

Open

1789

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

1790

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring compliance. Certification per EN 10204 3.1 also incl...

Open

1791

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

1792

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA and specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

1793

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

1794

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number as required, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

1795

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

1796

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the specification and documentation process. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORS...

Open

1797

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive te...

Open

1798

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with explicit coverage of mechanical, chemical, and testing requirements for 25 Cr Duplex stainless steel s...

Open

1799

1.0

AI

No

add date

No evidence of supplier qualification to NORSOK M-650/ISO 17782 for the exact product supplied or availability of QTR/MPCR documentation as required by the specification. MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV 25.7N but not ISO 17782...

Open

1800

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N (UNS S32760) within specified wall thickness limits, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 requirements. Source: DMV_STANDARD_BOOK/02 ...

Open

1801

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N complies with the required chemical analysis in Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

1802

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the product in question. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

1803

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed per ASTM A790, with manufacturing process and furnaces qualified according to NORSOK M-650 or ISO 17782, ensuring compliance with requirements including free circulation...

Open

1804

4.1

AI

No

add date

There is no confirmation that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790. Some tests are mentioned as feasible or standard, but no...

Open

1805

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

1806

4.1

AI

No

add date

Test sampling details including test methods, directions, and thickness locations for tensile, hardness, CVN, corrosion, and microstructure are not fully specified or confirmed. Test direction for tensile and CVN, and explicit confirmation of all req...

Open

1807

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature with properties meeting or exceeding Table 4 (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%). NORSOK MDS D51 references ASTM A790, which requires mechanical testing in accordance with ASTM A370, fulfi...

Open

1808

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required in Table 4 are not explicitly stated or confirmed for DMV 25.7N; standard references and test mentions are present but without specific values to verify fulf...

Open

1809

4.3

AI

No

add date

No evidence that Charpy V-notch testing will be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1, or that results will meet Table 5 requirements for the specified product and order context. No explicit confirmation of testing or compl...

Open

1810

4.3

AI

No

add date

Pipe wall thickness of 18.26mm allows both longitudinal and transverse Charpy V-notch impact tests at -46°C, meeting the specified absorbed energy requirements for pipes with thickness >6mm. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Dest...

Open

1811

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination per ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels. Grain size examination procedures for austenitic materials are not applicable to dupl...

Open

1812

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination or to reveal ferrite balance and intermetallic phases. No relevant references found to the specified etchants or s...

Open

1813

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic phases; isolated phases are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

1814

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at actual magnification (400x minimum) with a scale bar if intermetallic phases are not detected. Requirements for actual magnification and scale bar ...

Open

1815

4.4.2

AI

No

add date

No relevant documents address the detection, reporting, or acceptance criteria for centerline intermetallic stringers or link acceptance to CVN and corrosion test results if such stringers are present. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size ...

Open

1816

4.4.2

AI

No

add date

Standards allow isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not meet the stricter requirement that intermetallic phases and/or precipitates are not permitted if CVN testing cannot be completed...

Open

1817

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided; only grain size measurement is discussed, which is not relevant to the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-0...

Open

1818

4.4.3

AI

No

add date

No acceptance criteria or results for micrographic examination are provided for DMV 25.7N; relevant documents do not address or fulfill the requirement for section 4.4 Micrographic Examination or metallurgical properties related to microstructure for...

Open

1819

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly fulfilled for DMV 25.7N as stated in the specifications and compliance statements for NORSOK MDS D41 and D51. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD...

Open

1820

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided in the relevant documentation or metadata. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1821

4.5

AI

No

add date

No explicit acceptance criteria for metallurgical properties such as microstructure, phase balance, or grain size for DMV 25.7N are provided in the referenced documents. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/0...

Open

1822

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² matches the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

1823

5.1

AI

No

add date

No provided documents contain information on the qualification or certification of NDE personnel to ISO 9712 level II or III, nor on their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-...

Open

1824

5.2

AI

No

add date

No explicit confirmation of 100% ultrasonic testing per ASTM E213 or ISO 10893-10, calibration notch details, or process sequence after all processing is provided for validation of the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02...

Open

1825

5.2

AI

No

add date

100% qualitative anti-mixing PMI check is performed on standard production at Montbard using appropriate instruments, fulfilling general NDE acceptance criteria for PMI. Source: DMV_STANDARD_BOOK/12-06-06 - Positive Material Identification (PMI) in M...

Open

1826

5.2

AI

No

add date

ASTM A790 (via ASTM A999) requires that any indication greater than the calibration notch is considered a defect and such pipes must be rejected or repaired, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

1827

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for the specified product are confirmed as per the applicable ASTM standards (including ASTM A 790 with A 999 for tolerances), with no deviations or exceptions noted for the relevant dimensions. No overr...

Open

1828

7.0

AI

No

add date

ASTM A790 and NORSOK MDS S01 require finished pipes to be pickled or bright annealed, fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS S01 Rev 05 .docx

Open

1829

9.0

AI

No

add date

Weld repairs are not acceptable as per NORSOK MDS S01 Rev 05 for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

1830

10.0

AI

No

add date

No evidence of the manufacturer's quality-assurance system or ISO 9001 certification by a competent EEA body is provided in the available documents. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Certification Mo...

Open

1831

10.1

AI

No

add date

No evidence that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification or that the required documentation will be submitted to TechnipFMC for approval. Source: DMV_STANDARD_BOOK/14 - Inspection - Documen...

Open

1832

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV25.7N up to 31.75 mm WT (required: 18.26 mm), and the EN 10204 type 3.1 certificate will include the NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, demonstrating ...

Open

1833

10.2

AI

No

add date

No provided documentation confirms that required documentation traceable to the products will be transmitted to TechnipFMC, nor is there evidence of an appropriate quality-assurance system (e.g., ISO 9001) certified by a competent EEA body with speci...

Open

1834

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 is issued and validated for mill inspection, which is standard practice for including information required by ASTM A790 and NORSOK M-630 for these grades and specifications. Source: 14-03 - Certif...

Open

1835

10.2

AI

No

add date

None of the provided documents contain the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or metallurgical a...

Open

1836

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

1837

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence provided for full qualification to both NORSOK M-650/ISO 17782 or availability of QTR/MPCR as required by the specification. Sour...

Open

1838

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, fulfilling the requirement for manufacturer and process qualification and compliance with ...

Open

1839

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1840

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements and PREN minimum as specified in Table 2. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1841

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

1842

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for one set per heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

1843

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

1844

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled for DMV 25.7N as p...

Open

1845

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with tensile and hardness properties meeting Table 4 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Diges...

Open

1846

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW for S32760. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

1847

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

1848

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C, with minimum absorbed energy values for both transverse and longitudinal directions, and the specified pipe dimensions allow for required testing directions and speci...

Open

1849

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants after final polishing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

1850

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

1851

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

1852

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

1853

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

1854

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

1855

4.4.2

AI

No

add date

The available specifications allow isolated intermetallic precipitates below 10μm, but do not prohibit all intermetallic phases and/or precipitates if CVN testing cannot be completed, as required by the client. Zero-tolerance is not guaranteed in the...

Open

1856

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

1857

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR availability as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1858

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

1859

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% and DMV 25.7N complies per ISO 17781 and ASTM E1245. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06....

Open

1860

4.5

AI

No

add date

No explicit evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or referenced in the provided documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1861

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content...

Open

1862

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m²; DMV 25.7N complies. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

1863

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712 for the Montbard plant or the specified product and process context. ...

Open

1864

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 or ISO 10893-10 is feasible for the specified pipe dimensions and supported as a standard practice. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive t...

Open

1865

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT) is confirmed, but compliance with the additional NDE requirements of NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782 is not demonstrated. For the specified OD, eddy current testing is not feasible, and h...

Open

1866

5.2

AI

No

add date

No provided document explicitly states that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor confirms NDE acceptance criteria or standard NDE application for the specified pipe size and requi...

Open

1867

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790 referencing ASTM A999) for the specified dimensions, with no overriding requirements stated by the customer. Source: DMV_STANDARD_BOOK/07-01 - General information....

Open

1868

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

1869

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02...

Open

1870

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

1871

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

1872

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demonst...

Open

1873

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

1874

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference). ...

Open

1875

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, actual chemical analysis results, solution annealing temperature, holding time and quench m...

Open

1876

1.0

AI

No

add date

DMV 25.7N is a 25 Cr Duplex stainless steel seamless pipe fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all referenced mechanical, chemical, and testing requirements. Manufacturing is M-650 qualified up to the required wal...

Open

1877

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, fulfilling the requirement for manufacturer and process qualification and compliance with ...

Open

1878

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev...

Open

1879

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PREN ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1880

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

1881

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

1882

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

1883

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), corrosion, and microstructure tests at specified locations and directions. For the specified pipe di...

Open

1884

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370, and material meets the tensile and maximum hardness properties of Table 4 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 -...

Open

1885

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 and ASTM A790 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

1886

4.5

AI

No

add date

No direct evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is fulfilled. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1887

4.3

AI

No

add date

Pipe wall thickness exceeds the minimum required for Charpy V-notch testing; Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible and fulfilled for the specified product. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive tes...

Open

1888

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C (transverse: avg 45 J, single 35 J; longitudinal: avg 65 J, single 50 J), and the specified pipe dimensions allow for required transverse Charpy V-notch testing. Sour...

Open

1889

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, with specified etchants for intermetallic phases and ferrite balance after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

1890

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

1891

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

1892

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

1893

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

1894

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

1895

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully met. Source: ...

Open

1896

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

1897

4.4.3

AI

No

add date

Microstructure examination is performed as per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Acceptance criteria: structure must be basically free from intermetallic precipitates (isolated preci...

Open

1898

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

1899

4.5

AI

No

add date

Corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is not explicitly confirmed or referenced in the provided documentation or standards list. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1900

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

1901

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A @ 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and complies with these requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

1902

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

1903

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, performed after all mechanical processing as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-...

Open

1904

5.2

AI

No

add date

NDE per ASTM A790 and NORSOK M-630 MDS D51 is not confirmed; standard NDE (hydrostatic, EC, UT) is not fully feasible for the specified OD at Montbard, and full-length dye penetrant testing is not provided by default. No explicit confirmation of comp...

Open

1905

5.2

AI

No

add date

No provided document explicitly states that any indication greater than the calibration notch is considered a defect requiring rejection or repair of pipe/tubing, nor confirms NDE will be performed as standard for the requested size and specification...

Open

1906

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) as required, with no overriding specification from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances a...

Open

1907

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

1908

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

1909

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

1910

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

1911

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

1912

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

1913

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 manufacturing summary or QTR number, are provided and fulfill the requirement for documentation traceable to delivered products as ...

Open

1914

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with issuance and validation by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

1915

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. All other docum...

Open

1916

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all referenced mechanical, chemical, and testing requirements, and are M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK...

Open

1917

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 or availability of Qualification Test Records (QTR/MPCR) is provided. MST-Tubes is NORSOK M-650 accredited but not ISO 17782 accredited, so the requirement is not fully fulfille...

Open

1918

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

1919

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSO...

Open

1920

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

1921

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

1922

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with lot defined per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

1923

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

1924

4.1

AI

No

add date

Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations, are fulfilled. The pip...

Open

1925

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and the material meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dige...

Open

1926

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

1927

4.3

AI

No

add date

No evidence provided that Charpy V-notch testing will be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1, or that results will meet Table 5 requirements for the specified product. Only feasibility is mentioned, not actual compliance ...

Open

1928

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements, including Charpy V-notch testing at -46°C with specified minimum absorbed energies, and the pipe dimensions allow for required transverse and longitudinal testing as per the specifica...

Open

1929

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH solution after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

1930

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

1931

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect intermetallic phases, in accordance with ISO 17781, is explicitly required for micrographic examination, fulfilling the requirement for suitable etchants as listed in ISO 17781 Appendix B to show ferrite bal...

Open

1932

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

1933

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STANDA...

Open

1934

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

1935

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

1936

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size, so the requirement is not fully fulfilled. Sou...

Open

1937

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

1938

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

1939

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

1940

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1941

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite content, and microstructure requirements, with compliance confirmed by destructive and micrographic tests. Source: DMV_STAN...

Open

1942

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours is performed for DMV 25.7N, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², both of which are fulfilled. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

1943

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

1944

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within the machine's capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive...

Open

1945

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1946

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1947

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed. Standard NDE methods (EC/UT, hydrostatic) for the specified OD are only available at extra cost or require technical consultation, and full-length dy...

Open

1948

5.2

AI

No

add date

The available documents do not specify that any indication greater than the calibration notch is a defect requiring rejection or repair, nor do they confirm standard NDE methods are feasible for the requested pipe size at Montbard. Requirement cannot...

Open

1949

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 for seamless pipe under ASTM A790) unless otherwise specified, with no overriding requirements from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07.01 - General information.do...

Open

1950

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

1951

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

1952

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

1953

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

1954

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

1955

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

1956

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

1957

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51...

Open

1958

10.2

AI

No

add date

Most required documentation and certification details (NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and test results) are not provided. EN 10204 3.1 certificat...

Open

1959

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification digest and the customer specification listing 'A790 NORSOK'. M-650 qualification is also met for the required ...

Open

1960

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR availability as required. Full compliance with NORSOK M-650/ISO 17782 is not demonstrated for the exact product supplied ...

Open

1961

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN requirements as per Table 2, with explicit confirmation of conformity and supplier certification for each heat analysis. Source: 02-03-01 - Digest ASTM A 790.docx...

Open

1962

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

1963

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

1964

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

1965

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per NORSOK MDS D51/ASTM A79...

Open

1966

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or equivalent, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Hardness testing is also performed as specified. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

1967

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW, fulfilling the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

1968

4.3

AI

No

add date

No evidence provided that Charpy V-notch testing will be performed or that results will meet the requirements of Table 5 as specified by ASTM A370, ASTM A1058, or ISO 148-1. No explicit confirmation of compliance with the requirement is present in th...

Open

1969

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal if transverse is not possible. The specified pipe dimensions allow...

Open

1970

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

1971

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

1972

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

1973

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

1974

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

1975

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

1976

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met by the available infor...

Open

1977

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

1978

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

1979

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

1980

4.5

AI

No

add date

No direct evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or fulfilled for the requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

1981

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, chemical composition, ferrite content, and corrosion/impact requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

1982

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

1983

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

1984

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 can be performed, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-0...

Open

1985

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially met via 100% hydrostatic or NDE (EC or UT) testing, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD (...

Open

1986

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair; NDE methods for the specified OD are not standard or feasible at the plant without extra cost, and eddy current is not ...

Open

1987

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A...

Open

1988

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

1989

8.0

AI

No

add date

Marking per ASTM A790 and standard Montbard practices includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD...

Open

1990

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

1991

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

1992

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

1993

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling supplier qualification documentation requirem...

Open

1994

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

1995

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

1996

10.2

AI

No

add date

Most documentation and certification requirements are stated as included (NORSOK M-650/ISO 17782 identification, melting practice, heat treatment condition, chemical analysis, metallurgical and NDT results), but the specific steel producer of the sta...

Open

1997

1.0

AI

No

add date

DMV 25.7N seamless pipe is confirmed as compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-0...

Open

1998

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability or full compliance with both NORSOK M-650/ISO 17782 as required by the specification. Source: DMV_STAND...

Open

1999

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

2000

3.1

AI

No

add date

AOD or equivalent steel refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2001

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis is performed per heat and matches the required limits for all elements listed in the requ...

Open

2002

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

2003

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is carried out for each heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

2004

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

2005

4.1

AI

No

add date

Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions, are ful...

Open

2006

4.2

AI

No

add date

Tensile testing is performed at room temperature per required standards, with mechanical properties and hardness requirements matching Table 4; compliance with ASTM A370 or ISO 6892-1 and NORSOK MDS D51 is confirmed. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

2007

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 06 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

2008

4.3

AI

No

add date

No evidence that Charpy V-notch testing will be performed or that it meets ASTM A370, ASTM A1058, or ISO 148-1 with an 8 mm striker radius and Table 5 requirements; only feasibility based on wall thickness and pipe size is confirmed, not actual compl...

Open

2009

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, with the specified minimum absorbed energy values for both transverse and longitudinal directions. The requested pipe dimensions allow for both test orientations as...

Open

2010

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

2011

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, is specified and matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

2012

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

2013

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are reported with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

2014

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, reported at actual magnification and including a scale bar, if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - ...

Open

2015

4.4.2

AI

No

add date

Presence of centerline intermetallic stringers must be reported and acceptance is based on CVN and corrosion test results, as specified for micrographic examination in NORSOK MDS D51 Rev 06 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

2016

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates, which does not meet the stricter client requirement of not permitting any i...

Open

2017

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

2018

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corro...

Open

2019

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev ...

Open

2020

4.5

AI

No

add date

DMV 25.7N complies with all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive tests, microstructure, and ferrite content requirements for the specified wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

2021

4.5

AI

No

add date

Requirement for no pitting at 20X magnification and weight loss less than 1.0 g/m² is fulfilled per NORSOK MDS D51 Rev 06, which specifies ISO 17781 G48 Method A testing with these acceptance criteria for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

2022

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor are their roles and responsibilities defined as per ISO 9712 requirements. Source: DMV_STANDARD_BOOK/12-02-01 - N...

Open

2023

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

2024

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not fully addressed; only ASTM A790/A999 NDE is confirmed. For OD 219.1 mm, eddy current is not feasible, hydrostatic and ultrasonic are only available at extra cos...

Open

2025

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair, and current plant NDE capabilities for the specified OD do not confirm fulfillment of the requirement for this acceptan...

Open

2026

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) as required, with no deviations or special tolerances specified in the client request or drawing. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOO...

Open

2027

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2028

8.0

AI

No

add date

Marking includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAND...

Open

2029

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated in the specification for DMV 25.7N seamless pipe under NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

2030

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

2031

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

2032

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number as required, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

2033

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dige...

Open

2034

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control for mill inspection. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK...

Open

2035

10.2

AI

No

add date

Most required documentation and certification items (NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel melting practice and refining method, heat number, chemical analysis, solution annealing details, metallurgical and NDT results) are ...

Open

2036

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

2037

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782, and there is no confirmation of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest ...

Open

2038

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

2039

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2040

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PREN ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2041

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

2042

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

2043

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

2044

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per ASTM A790 and NORSOK re...

Open

2045

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370, and the material meets the tensile and maximum hardness properties of Table 4 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-0...

Open

2046

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

2047

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact ...

Open

2048

4.4.3

AI

No

add date

Ferrite content is determined per ASTM E562 or by image analysis according to ASTM E1245, performed in accordance with ISO 17781, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-...

Open

2049

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C, including minimum absorbed energy values for both transverse and longitudinal directions and sub-size specimen reduction factors. The specified pipe dimensions allow...

Open

2050

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching for intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and examination in accordance ...

Open

2051

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

2052

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

2053

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

2054

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum 400x magnification, with representative micrographs at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STA...

Open

2055

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 requires reporting of intermetallic phases, with acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria...

Open

2056

4.4.2

AI

No

add date

No provided documentation confirms that intermetallic phases and/or precipitates are completely prohibited if CVN testing cannot be completed; the closest reference allows isolated precipitates below 10μm, which does not meet the stricter client requ...

Open

2057

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

2058

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Structure must be basically free from intermetallic precipitates; isolated precipitates allowed if not d...

Open

2059

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

2060

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

2061

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, microstructure, and ferrite content requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

2062

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

2063

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

2064

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 or ISO 10893-10 is feasible after all processing steps, and reference notches per ASTM E213 are supported for the specified pipe dimensions. Source: DMV_STANDARD_BOOK/12 - ...

Open

2065

5.2

AI

No

add date

NDE per ASTM A790 is partially feasible, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782 requirements are addressed. For OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only a...

Open

2066

5.2

AI

No

add date

No provided document explicitly confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that the required NDE acceptance criteria are standardly performed or feasible for the specified pi...

Open

2067

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed as per ASTM A790 and ASTM A999 for the specified dimensions, with no deviations stated, fulfilling the requirement that tolerances follow the applicable ASTM standard unless otherwise speci...

Open

2068

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2069

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods at Montbard include heat number and DMV lot number, ensuring compliance. Certification per EN 10204 3....

Open

2070

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

2071

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

2072

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, and the QTR number is included in the certificate, fulfilling the requirement for supplier qualification documentation per SIR131. Source: DMV_STANDARD_BOOK/0...

Open

2073

10.2

AI

No

add date

No evidence that documentation traceable to the products (SIR205) will be transmitted to TechnipFMC as required; only general certification and inspection certificate information is provided without explicit confirmation of compliance with the docume...

Open

2074

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control and reference to the relevant standards throughout the specification. Source: DMV_STANDARD_BOOK/02-04-0...

Open

2075

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution annealing parameters, an...

Open

2076

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

2077

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not to ISO 17782, as required. No evidence provided for QTR/MPCR availability or full compliance with both standards for the exact product supplied. Source: DMV_STANDARD_BOOK/02 - S...

Open

2078

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements for the specified WT of 18.26 mm. Source: ...

Open

2079

3.1

AI

No

add date

AOD or equivalent refining is used for 100% of production and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2080

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the requirement table and DMV material composition conforms with supplier certification and heat analysis per ASTM A790 Table 2 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

2081

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification will state heat treatment condition as per ASTM A790. Pipes are processed to ensure ...

Open

2082

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

2083

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dige...

Open

2084

4.1

AI

No

add date

DMV 25.7N seamless pipes are tested per NORSOK MDS D51/ASTM A790 requirements, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations. ...

Open

2085

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, with material meeting the tensile and maximum hardness properties of Table 4 as required for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

2086

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW, fulfilling Table 4 mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

2087

4.3

AI

No

add date

Pipe dimensions exceed minimum requirements for Charpy V-notch testing as per ASTM A370, ASTM A1058, or ISO 148-1; testing is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 -...

Open

2088

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C (transverse: 45 J avg/35 J single, longitudinal: 65 J avg/50 J single if transverse not possible). The specified pipe dimensions allow for required transverse Charpy ...

Open

2089

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

2090

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2091

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is specified and fulfills the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-...

Open

2092

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

2093

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

2094

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

2095

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

2096

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is...

Open

2097

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

2098

4.4.3

AI

No

add date

Micrographic examination is performed as per ISO 17781 with specified etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, and findings of carbides/nitrides reported. Acceptance...

Open

2099

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is specified and fulfilled for DMV 25.7N according to NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

2100

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

2101

4.5

AI

No

add date

DMV 25.7N complies with all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

2102

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

2103

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

2104

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 and ISO 10893-10 is available and applicable for the requested pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ul...

Open

2105

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all relevant chemical, mechanical, manufacturing, and testing requirements. M-650 qualification is confirmed for the required wall thickness. Sourc...

Open

2106

5.2

AI

No

add date

NDE per ASTM A790 is partially aligned via ASTM A999 (hydrostatic or EC/UT), but there is no explicit evidence of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782. For OD 219.1 mm, eddy current testing is not feasible, and hydrost...

Open

2107

5.2

AI

No

add date

No explicit confirmation that NDE acceptance criteria require rejection or repair of any indication greater than the calibration notch; feasibility of required NDE for the specified dimension is not confirmed for Montbard plant. Source: DMV_STANDARD_...

Open

2108

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A...

Open

2109

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2110

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 (§14), requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring compliance with the requirement. Source: DMV_S...

Open

2111

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated in NORSOK MDS D51 Rev 06, §14 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK...

Open

2112

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

2113

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

2114

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, fulfilling the qualification requirement. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

2115

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

2116

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51...

Open

2117

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or complete metallurgical and non-dest...

Open

2118

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability for review. Requirement for qualification to both NORSOK M-650/ISO 17782 and documentation availability...

Open

2119

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

2120

3.1

AI

No

add date

AOD or equivalent refining is used and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2121

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed by supplier certification and heat analysis per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02...

Open

2122

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

2123

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for each heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

2124

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

2125

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specifi...

Open

2126

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

2127

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW, fulfilling all specified mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

2128

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact ...

Open

2129

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C, including minimum absorbed energy values for transverse and longitudinal directions, and the specified pipe dimensions allow for required testing directions and spec...

Open

2130

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

2131

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is explicitly required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_...

Open

2132

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

2133

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

2134

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included with presence and location of intermetallic phases noted and recorded. Source: DMV_STANDA...

Open

2135

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

2136

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

2137

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

2138

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

2139

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with required etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impac...

Open

2140

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS ...

Open

2141

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

2142

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including chemical composition, PRE, tensile, impact, corrosion, microstructure, ferrite content, and M-650 qualification for the specified wall thickness. Source: DMV_ST...

Open

2143

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

2144

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

2145

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is fulfilled for the specified pipe dimensions; compliance with ASTM E213 implies adherence to calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testi...

Open

2146

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT testing) is confirmed, but there is no evidence of compliance with additional NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782 requirements. Standard NDE is not feasible for the specified OD at Montb...

Open

2147

5.2

AI

No

add date

No provided documentation explicitly states that any indication greater than the calibration notch is considered a defect requiring rejection or repair, and standard NDE methods are not feasible for the requested OD at Montbard, preventing fulfillmen...

Open

2148

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or specified. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

2149

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 for ASTM A790 pipe), with no evidence of a different requirement from TechnipFMC. OD, WT, and ovality tolerances for the specified dimensions are confirmed as per ASTM standard. S...

Open

2150

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2151

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot; standard marking methods (indelible ink, vibro-etching) include heat number and DMV lot number as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Re...

Open

2152

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

2153

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

2154

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

2155

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

2156

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

2157

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant standards and qualifications as required for the material and plant in que...

Open

2158

10.2

AI

No

add date

Documentation will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin, not the specific steel producer, is provided. No evidence of actual heat number, chemical analysis...

Open

2159

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

2160

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782, and there is no confirmation of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Dige...

Open

2161

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

2162

3.1

AI

No

add date

AOD or equivalent refining is used 100% for DMV 25.7N, and chemical composition complies with Table 2 requirements of ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2163

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements; DMV material composition is stated to comply and heat analysis is performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

2164

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

2165

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

2166

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, directly referencing the required table for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

2167

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per NORSOK MDS D51/ASTM A79...

Open

2168

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

2169

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

2170

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

2171

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements: Charpy V-notch testing at -46°C with minimum transverse values of 45 J (average) and 35 J (single), and longitudinal values of 65 J (average) and 50 J (single) if transverse is not pos...

Open

2172

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

2173

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is explicitly required and matches the specification requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

2174

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

2175

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases. Source: DMV_STANDARD_BOOK/02...

Open

2176

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

2177

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

2178

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with required etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impac...

Open

2179

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2180

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is fulfilled; neither standard nor test is mentioned or specified in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests i...

Open

2181

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

2182

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781 (G48 Method A @ 50°C, 24h). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Diges...

Open

2183

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

2184

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

2185

5.2

AI

No

add date

NDE per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 is not fully addressed; standard NDE (EC, UT, hydro) for 219.1 mm OD pipe at Montbard is not available or only possible at extra cost and with technical consultation; no evidence of full-l...

Open

2186

5.2

AI

No

add date

No provided document confirms that indications greater than the calibration notch are classified as defects requiring rejection or repair, nor that the required NDE will be performed as standard for the specified pipe size and grade. Source: DMV_STAN...

Open

2187

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no deviations specified by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A 376-02a A 790...

Open

2188

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2189

8.0

AI

No

add date

Marking is performed per ASTM A790 §14 and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

2190

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03...

Open

2191

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

2192

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

2193

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of full qualification to NORSOK M-650/ISO 17782 or availability of QTR/MPCR as required by the specification. Source: DMV_ST...

Open

2194

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness as required for qualification. Source: DMV_STANDARD_BOOK/...

Open

2195

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products as required by SIR205 and section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

2196

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

2197

10.2

AI

No

add date

No provided documentation includes all required items: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or actual metallurgical and non-destruct...

Open

2198

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

2199

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV25.7N (UNS S32760) up to WT = 31.75 mm, with manufacturing process qualified to NORSOK M-650/ISO 17782, and compliance with NORSOK M-630 MDS D51 Rev. 6 is referenced. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

2200

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2201

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements. Heat analysis is performed per heat, fulfilling the chemistry requirement for S32760. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

2202

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

2203

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

2204

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ...

Open

2205

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, in accordance with NORSOK MDS D...

Open

2206

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, with material meeting the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

2207

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW, fulfilling all Table 4 mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

2208

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and standards; requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/1...

Open

2209

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements (Charpy V-notch at -46°C: transverse 45J/35J, longitudinal 65J/50J, sub-size reduction factors). The specified pipe dimensions allow for required impact testing directions and...

Open

2210

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

2211

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is explicitly required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_...

Open

2212

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

2213

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

2214

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report at actual magnification and with a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/...

Open

2215

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

2216

4.4.2

AI

No

add date

No provided documentation confirms a zero-tolerance policy for intermetallic phases and/or precipitates when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10 µm, which does not meet the stricter client requ...

Open

2217

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard alignment. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

2218

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), in compliance with NORSOK MDS D51 and ...

Open

2219

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

2220

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or referenced. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

2221

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO ...

Open

2222

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A @ 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and compliance is confirmed. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

2223

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

2224

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 or ISO 10893-10 is confirmed for the specified pipe dimensions, and calibration is expected to follow ASTM E213 Figure 3 as required. Source: DMV_STANDARD_BOOK/12 - Special...

Open

2225

5.2

AI

No

add date

NDE per ASTM A790 is partially addressed (hydrostatic or NDE per ASTM A999), but there is no explicit evidence of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE acceptance criteria. For the requested OD, eddy curren...

Open

2226

5.2

AI

No

add date

No provided document confirms that indications greater than the calibration notch are classified as defects requiring rejection or repair, nor is there confirmation that the required NDE methods and acceptance criteria will be applied for the specifi...

Open

2227

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no override specified in the customer requirements or context. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK...

Open

2228

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be pickled or bright annealed, directly fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2229

8.0

AI

No

add date

Marking per ASTM A790 and DMV standards includes mandatory marking of heat number, lot number, and other traceability data, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

2230

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

2231

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

2232

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the specified quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

2233

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

2234

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

2235

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with issuance and validation by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

2236

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical...

Open

2237

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification digest and the listed customer specifications for the requested item. Manufacturing is M-650 qualified up to the...

Open

2238

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782, as explicitly required. No evidence of QTR/MPCR availability for review is provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2239

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to 31.75 mm WT, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

2240

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev...

Open

2241

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements. Heat analysis is performed per heat as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 ...

Open

2242

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured ...

Open

2243

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

2244

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling as outlined in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

2245

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is performed per NORSOK MDS D51/ASTM A790. Fo...

Open

2246

4.2

AI

No

add date

Tensile testing is performed at room temperature per required standards, with mechanical properties and hardness requirements matching Table 4; compliance with ASTM A370 or ISO 6892-1 and NORSOK MDS D51 is confirmed. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

2247

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥750 MPa, yield strength ≥550 MPa, elongation ≥25%, and hardness ≤310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

2248

4.3

AI

No

add date

Pipe dimensions exceed minimum wall thickness required for Charpy V-notch testing as per ASTM A370, ASTM A1058, or ISO 148-1; testing is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing...

Open

2249

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, with minimum absorbed energy values for transverse and longitudinal specimens, and the specified pipe dimensions allow for required testing orientation and specimen...

Open

2250

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

2251

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH is used to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

2252

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

2253

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

2254

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

2255

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

2256

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

2257

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

2258

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Acceptance criteria: structure is basically free from intermetallic precipitates (isolated precipitates <1...

Open

2259

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

2260

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

2261

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, chemical composition, ferrite content, and corrosion/impact requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

2262

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

2263

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destruct...

Open

2264

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 can be performed after all processing, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destru...

Open

2265

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/NORSOK M-650 are not fully addressed. Provided documents confirm general NDE per ASTM A999 but lack explicit evidence of NORSOK-specific NDE requirements or acceptance criteria. Feasibili...

Open

2266

5.2

AI

No

add date

No provided document confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor that this NDE acceptance criterion is standard or feasible for the specified pipe dimension at Montbard. ND...

Open

2267

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and ASTM A999 as required, with no overriding specification from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312...

Open

2268

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2269

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

2270

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for seamless pipe, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

2271

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

2272

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

2273

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for the relevant product form and wall thickness, with certification including NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, demonstrating qualification for the size and product form. ...

Open

2274

10.2

AI

No

add date

ISO 9001 certification by a competent body is confirmed, and documentation traceable to delivered products is provided as required by SIR205 and specification section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

2275

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, 14-03 - Certification Montbard plant.doc

Open

2276

10.2

AI

No

add date

Documentation and certification elements such as NORSOK M-650/ISO 17782 identification, QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and explicit metallurgical and non-destructive test...

Open

2277

1.0

AI

No

add date

DMV 25.7N is a 25 Cr Duplex stainless steel seamless pipe fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the customer requirements and confirmed in the standards digest. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

2278

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

2279

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2280

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements. Heat analysis is performed per heat as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 ...

Open

2281

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

2282

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

2283

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the specified frequency, fulfilling the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detai...

Open

2284

4.1

AI

No

add date

All required destructive tests (tensile, hardness, CVN, corrosion, microstructure) for seamless pipes are performed as specified, with CVN transverse specimens feasible for the given dimensions. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS ...

Open

2285

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

2286

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets the minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) requirements per NORSOK MDS D51 Rev 6 and ASTM A790 references. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

2287

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for 18.26mm wall thickness and 219.1mm OD as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tes...

Open

2288

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact test requirements: Charpy V-notch at -466C, minimum average 45 J and single 35 J in transverse direction, 65/50 J in longitudinal if transverse not possible, including sub-size reduction factors. ...

Open

2289

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH solution after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

2290

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is required for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

2291

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

2292

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases as required. Source: DMV_STAN...

Open

2293

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and scale bar, fulfilling the requirement for representative micrographs at or near mid-wall thickness. Source: DMV_STANDARD_B...

Open

2294

4.4.2

AI

No

add date

Findings of intermetallic phases must be reported, and acceptance is based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

2295

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

2296

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content measurement per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

2297

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with defined etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact...

Open

2298

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2299

4.5

AI

No

add date

No explicit confirmation or evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

2300

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite content, and microstructure requirements, and is compliant with ASTM A790 and NORSOK M-650/ISO 17782 standards. Source: DMV...

Open

2301

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A @ 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m²; requirement is fulfilled. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spe...

Open

2302

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in...

Open

2303

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is feasible for the specified pipe dimensions after all processing steps. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultraso...

Open

2304

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially addressed, but NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782-specific NDE requirements are not validated. For the requested OD (219.1 mm), eddy current testing is not standardly feasible, an...

Open

2305

5.2

AI

No

add date

No provided documentation explicitly confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that this is standard practice or feasible for the specified OD at the Montbard plant. Source:...

Open

2306

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 seamless pipe are per the applicable ASTM standard (ASTM A999), with no override specified by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances accordin...

Open

2307

7.0

AI

No

add date

ASTM A790 (6.1.3) and NORSOK MDS D51 (§13) both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2308

8.0

AI

No

add date

Marking per ASTM A790 includes traceability to melt and heat treatment lot, and marking methods (indelible ink, vibro-etching) at Montbard plant include heat number and DMV lot number, ensuring full traceability. Source: Digest NORSOK MDS D51 Rev 06....

Open

2309

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' confirming the requirement is met. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev...

Open

2310

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

2311

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body established within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

2312

10.1

AI

No

add date

Supplier is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the requirement for qualification for the specif...

Open

2313

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 ...

Open

2314

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications and plant documentation. Source: DMV_STANDARD_BOOK/02-04-03 - Dig...

Open

2315

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and...

Open

2316

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, including chemical, mechanical, manufacturing, and testing requirements. M-650 qualification is confirmed for the required ...

Open

2317

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782, and there is no evidence of QTR/MPCR availability for review as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

2318

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

2319

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2320

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2321

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650/ISO 17782. Pipes are placed to ensure free circulation of heating and coo...

Open

2322

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

2323

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

2324

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure tests are performed at specified locations an...

Open

2325

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

2326

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

2327

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness (>6mm), fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - ...

Open

2328

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse 45/35 J and longitudinal 65/50 J for thickness >6mm; product dimensions allow required testing and fulfillment. Source: DMV...

Open

2329

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with specified etchants after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

2330

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

2331

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

2332

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

2333

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, actual magnification and scale bar reported, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

2334

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - D...

Open

2335

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates below 10μm, which does not meet the stricter client requirement of no interm...

Open

2336

4.4.3

AI

No

add date

Ferrite content is determined per ASTM E562 or ASTM E1245, performed in accordance with ISO 17781, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

2337

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, including etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and co...

Open

2338

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2339

4.5

AI

No

add date

DMV 25.7N (UNS S32760) fulfills all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, ferrite content, and qualification per NORSOK MDS D51 Rev 6, ASTM A790, an...

Open

2340

4.5

AI

No

add date

DMV 25.7N undergoes pitting corrosion testing per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

2341

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

2342

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive tes...

Open

2343

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/ M-650/ISO 17782 are not fully addressed; standard NDE methods (hydrostatic, EC, UT) are either not feasible for the specified OD or only available at extra cost and require technical con...

Open

2344

5.2

AI

No

add date

No explicit confirmation of the calibration notch-based rejection criterion in the referenced standards or plant practices; standard NDE method (Eddy current) is not feasible for the requested OD at Montbard, preventing fulfillment of the requirement...

Open

2345

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 for ASTM A790 pipe), with no evidence of override by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to AS...

Open

2346

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSO...

Open

2347

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/1...

Open

2348

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2349

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

2350

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the specified quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

2351

10.1

AI

No

add date

Supplier is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the requirement for qualification for the specif...

Open

2352

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

2353

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications and documentation scope. Source: DMV_STANDARD_BOOK/02-04-03 - Dig...

Open

2354

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and n...

Open

2355

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with explicit coverage of mechanical, chemical, and testing requirements for 25 Cr Duplex stainless steel s...

Open

2356

1.0

AI

No

add date

No document confirms supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor the availability of the full Qualification Test Record/MPCR for review by TechnipFMC as required by the specification. Source: DMV_STAN...

Open

2357

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm for hot finished, 10.925 mm for cold finished), and the manufacturing process is qualified per NORSOK M-650 (or ISO 17782), meeting NORSOK M-630 MDS D51 rev. 6 requi...

Open

2358

3.1

AI

No

add date

AOD or equivalent refining is used for 100% of production, and DMV 25.7N chemical analysis complies with the required standard. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51...

Open

2359

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the inquiry's wall thickness of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

2360

3.2

AI

No

add date

Solution annealing followed by accelerated cooling is performed per ASTM A790; manufacturing and furnace qualification comply with NORSOK M-650/ISO 17782; free circulation of heating/cooling media is ensured by these standards. Source: DMV_STANDARD_B...

Open

2361

4.1

AI

No

add date

No provided document confirms that impact, tensile, hardness, corrosion testing, and microstructure examinations are performed for each heat and heat treatment lot as defined in ASTM A790. Testing frequency and lot-based compliance are not demonstrat...

Open

2362

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required by the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

2363

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no information on CVN impact testing, test directions for CVN, or requirements for hardness, corrosion, and microstructure tests, nor on specified sampling locations. Source: DMV_STANDARD_BOOK/...

Open

2364

4.2

AI

No

add date

Tensile testing is performed per ASTM A370, with results meeting or exceeding Table 4 requirements (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%). Hardness testing is also performed as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

2365

4.2

AI

No

add date

Mechanical property values for DMV 25.7N (UNS S32760/S32750) are not provided in the referenced documents, so fulfillment of tensile strength, yield strength, elongation, and hardness requirements cannot be confirmed. Source: DMV_STANDARD_BOOK/02-03-...

Open

2366

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the ordered pipe (NPS 8, 219.1mm OD, 18.26mm WT), as it exceeds the minimum wall thickness requirements for both standards. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Tes...

Open

2367

4.3

AI

No

add date

Impact property requirements for transverse and longitudinal Charpy V-notch specimens at -46°C are feasible and can be fulfilled for the specified pipe dimensions (OD 219.1 mm, WT 18.26 mm). Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot fi...

Open

2368

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination according to ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/1...

Open

2369

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination; requirement not fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - ...

Open

2370

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic phases; isolated phases are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

2371

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided or addressed in the reviewed documents. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Microg...

Open

2372

4.4.2

AI

No

add date

Micrographic examination at minimum 400x magnification is specified and photos are included, but it is not confirmed that a representative micrograph at or near mid-wall thickness is recorded when intermetallic phases are not detected, nor that micro...

Open

2373

4.4.2

AI

No

add date

No provided document addresses the reporting of centerline intermetallic stringers or links their acceptance to CVN and corrosion test results; requirement not fulfilled. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I.doc, DMV_S...

Open

2374

4.4.2

AI

No

add date

Referenced specifications allow isolated intermetallic precipitates below 10μm if not distributed over the whole specimen, which does not meet the client requirement of zero tolerance for intermetallic phases/precipitates when CVN testing cannot be c...

Open

2375

4.4.3

AI

No

add date

No information is provided regarding ferrite content determination per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781; only grain size measurement is discussed and the required methods are not addressed. Source: DMV_STANDARD_BOOK/12 - Special...

Open

2376

4.4.3

AI

No

add date

No acceptance criteria for micrographic examination or metallurgical properties are specified or referenced for DMV 25.7N in the provided documents. Source: Digest ASTM A 790.docx, Digest NORSOK MDS S01 Rev 05 .docx, Grain Size Examination in DMV-I.d...

Open

2377

4.4.3

AI

No

add date

No information is provided regarding any microstructural property or constituent in the 35%-60% range; only grain size measurement procedures and criteria are discussed, not percentage-based properties relevant to the requirement. Source: DMV_STANDAR...

Open

2378

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

2379

4.5

AI

No

add date

No acceptance criteria for metallurgical properties are specified for DMV 25.7N in the provided documentation. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

2380

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria: no pitting at 20X magnification and weight loss < 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

2381

5.1

AI

No

add date

No provided documents contain information about NDE personnel qualification or certification to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-0...

Open

2382

5.2

AI

No

add date

No evidence is provided confirming 100% ultrasonic testing per ASTM E213 or ISO 10893-10 after all processing, nor the required reference notch criteria per ASTM E213 Figure 3 are implemented. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - No...

Open

2383

5.2

AI

No

add date

Dye penetrant testing is performed on tube ends and bevels as specified, and 100% qualitative anti-mixing PMI is conducted on standard production, fulfilling the NDE acceptance criteria for the Montbard plant. Source: DMV_STANDARD_BOOK/12-02-05 - Dye...

Open

2384

5.2

AI

No

add date

ASTM A790 (via ASTM A999) requires that any indication greater than the calibration notch is considered a defect and such pipes must be rejected or repaired, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

2385

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for both hot and cold finished products, including the relevant sizes, are confirmed as compliant with the applicable ASTM standards (A 790 with A 999 for tolerances, A 213, A 268, A 269, A 312, A 376, A...

Open

2386

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2387

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and maximum hardness properties of Table 4. Hardness testing is performed per ASTM A790...

Open

2388

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

2389

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully met. Source: DMV_S...

Open

2390

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

2391

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 790-02 (A 999-01).doc,...

Open

2392

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

2393

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and test results—are not fully provided. Only the count...

Open

2394

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits and PREN requirement as specified in Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 06 standards. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2395

7.0

AI

No

add date

Finished pipes are required to be white pickled or bright annealed by both ASTM A790 and NORSOK MDS S01 standards, directly fulfilling the requirement. Source: ASTM A790, NORSOK MDS S01

Open

2396

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

2397

9.0

AI

No

add date

Weld repairs are not acceptable per NORSOK MDS S01 Rev 05 specification for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

2398

10.0

AI

No

add date

No evidence of an appropriate quality-assurance system (such as ISO 9001 certification by a competent EEA body) is provided for the Montbard plant or manufacturer. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - C...

Open

2399

10.1

AI

No

add date

No evidence is provided that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body with specific assessment for materials as required by the specification. Source: 14-03 - Certification Montbard plant.doc

Open

2400

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, and the QTR number is included in the certificate, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MCPR qual...

Open

2401

10.2

AI

No

add date

No evidence that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC as specified in the requirement. No explicit mention of SIR205 or traceability to TechnipFMC is provided for the Montbard plant or the s...

Open

2402

10.2

AI

No

add date

Material certificate is issued in accordance with EN 10204 Type 3.1 and includes information required by ASTM A790 and NORSOK M-630 as specified in customer requirements. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/...

Open

2403

10.2

AI

No

add date

None of the provided documents contain the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or test results...

Open

2404

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, including material, manufacturing, testing, and documentation. The product is M-650 qualified and meets all...

Open

2405

1.0

AI

No

add date

Supplier qualification to NORSOK M-650/ISO 17782 for the exact product and availability of QTR/MPCR for review are not confirmed by the provided information. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-...

Open

2406

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

2407

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition conforms to the specified table for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2408

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2409

3.2

AI

No

add date

Solution annealing followed by accelerated cooling is performed per ASTM A790; manufacturing and furnace qualification comply with NORSOK M-650/ISO 17782; MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensur...

Open

2410

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

2411

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and pieces, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

2412

4.1

AI

No

add date

Tensile, hardness, CVN (transverse or longitudinal if not feasible), and corrosion/microstructure tests for seamless pipes per ASTM A790 and NORSOK MDS D51 are covered, with correct test directions and thickness locations. Transverse CVN specimens ar...

Open

2413

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 as required for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

2414

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

2415

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and standards; requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/1...

Open

2416

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C, minimum absorbed energies (transverse: 45 J average/35 J single; longitudinal: 65 J average/50 J single if transverse not possible), and speci...

Open

2417

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with 20-40% NaOH or KOH solution after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

2418

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

2419

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

2420

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781, with etching to detect intermetallic phases at a minimum magnification of 400x, and photos are included; presence and location of intermetallic phases are noted and recorded as required. Source: DM...

Open

2421

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, actual magnification and scale bar reported if intermetallic phases are not detected, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

2422

4.4.2

AI

No

add date

Presence of centerline intermetallic stringers must be reported, and acceptance is based on CVN and corrosion test results as specified in the micrographic examination section. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

2423

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates, which does not meet the stricter client requirement of no intermetallic pha...

Open

2424

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_ST...

Open

2425

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosio...

Open

2426

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

2427

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided; compliance cannot be confirmed. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

2428

4.5

AI

No

add date

DMV 25.7N complies with all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

2429

4.5

AI

No

add date

DMV 25.7N meets the pitting corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours, with no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

2430

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

2431

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

2432

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. For the specified OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at extra cost. ...

Open

2433

5.2

AI

No

add date

No provided document specifies that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor confirms standard application of relevant NDE methods for the requested pipe dimensions and grade. Source:...

Open

2434

6.0

AI

No

add date

Dimensional tolerances are confirmed as per the applicable ASTM standard (ASTM A790 referencing ASTM A999) for the requested pipe dimensions, with no overriding requirements from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07-01 - General inform...

Open

2435

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2436

8.0

AI

No

add date

Marking per ASTM A790 includes traceability to melt and heat treatment lot; marking methods (indelible ink, vibro-etching) include heat number and DMV lot number, ensuring full traceability. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

2437

9.0

AI

No

add date

Weld repairs are explicitly stated as not acceptable under 'Surface finish / Repairs of defects' in the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

2438

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/...

Open

2439

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers as specified in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

2440

10.1

AI

No

add date

Supplier MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the requirement for qualification for ...

Open

2441

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03...

Open

2442

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and covering required details such as heat treatment, steel manufacturer, melting and refining practice, and ...

Open

2443

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of metallurgical and non-de...

Open

2444

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by explicit listing and specification digest. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2445

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782; no confirmation of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2446

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process follows M-650 (or ISO 17782) qualified procedures, fulfilling the requirement for manufacturer and process qualification and complianc...

Open

2447

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2448

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed by heat analysis with supplier certification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Dige...

Open

2449

3.2

AI

No

add date

Solution annealing followed by accelerated cooling per ASTM A790 is confirmed; manufacturing process and furnaces are qualified per NORSOK M-650/ISO 17782; free circulation of heating/cooling media is implicit in compliance with these standards. Sour...

Open

2450

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

2451

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

2452

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790/NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure at specified thickness locations. ...

Open

2453

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2454

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370, with required properties (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and hardness testing per ASTM A790, meeting Table 4 requirements for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

2455

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required in Table 4 for ASTM A790/NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

2456

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions (WT 18.26mm, OD 219.1mm), meeting the requirement for transverse specimens at this wall thickness. Source: DMV_STANDARD_BOOK/12-03-02 - Impac...

Open

2457

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements, including Charpy V-notch testing at -466C with minimum absorbed energy values (transverse: 45 J average, 35 J single; longitudinal: 65 J average, 50 J single if transverse n...

Open

2458

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

2459

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

2460

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

2461

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are reported with representative micrographs noting presence and location of intermetallic phases. Source...

Open

2462

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

2463

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

2464

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not fulfil...

Open

2465

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Sou...

Open

2466

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

2467

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

2468

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

2469

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, as well as manufacturing, heat treatment, and qualification requirements. Source: DMV_STAN...

Open

2470

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

2471

5.1

AI

No

add date

No information is provided confirming NDE personnel qualification or certification to ISO 9712 level II or III, nor definition of their roles and responsibilities as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibili...

Open

2472

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non des...

Open

2473

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT) is detailed, but compliance with NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782 is not confirmed. Eddy current testing is not feasible for the required OD, and feasibility for other NDE methods is not c...

Open

2474

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor details the acceptance criteria or confirms standard NDE capability for the specified dimensions...

Open

2475

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the specified pipe, with no overriding requirements from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - T...

Open

2476

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2477

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 (§14), both requiring full traceability to melt and heat treatment lot. Marking methods (indelible ink, vibro-etching) include heat and DMV lot numbers, ensuring compliance for all pipes a...

Open

2478

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2479

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

2480

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

2481

10.1

AI

No

add date

Certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR as required, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

2482

10.2

AI

No

add date

ISO 9001 certification by a competent body and traceable documentation including EN 10204 type 3.1 certificates and NORSOK M-650/ISO 17782 manufacturing summary or QTR number are provided, fulfilling the requirement for documentation and quality-assu...

Open

2483

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided; requirement cannot be confirmed as fulfilled. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

2484

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAN...

Open

2485

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or complete metallurgical and non-dest...

Open

2486

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and are M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - D...

Open

2487

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782; no evidence of QTR/MPCR availability or full qualification to both standards as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2488

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

2489

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2490

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and in accordance with ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STAND...

Open

2491

3.2

AI

No

add date

Solution annealing followed by accelerated cooling per ASTM A790 is confirmed; manufacturing process and furnace compliance with NORSOK M-650/ISO 17782 are met; free circulation of heating/cooling media is implicit in these standards. Source: DMV_STA...

Open

2492

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, with test frequency specified as '1/lot'. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

2493

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

2494

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure tests at specified locations and directions per NORSOK MDS D51/ASTM A...

Open

2495

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370, with required properties (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and hardness testing confirmed; DMV 25.7N complies with Table 4 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

2496

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

2497

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness requirements for transverse specimens. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destru...

Open

2498

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; the specified pipe dimensions allow for required transverse testing. Source...

Open

2499

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

2500

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is specified as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NO...

Open

2501

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

2502

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

2503

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

2504

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

2505

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

2506

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

2507

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with defined etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact...

Open

2508

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in accordance with ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

2509

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

2510

4.5

AI

No

add date

Acceptance criteria for metallurgical properties, including chemical composition, microstructure, ferrite content, impact, corrosion, and micrographic tests, are fulfilled per NORSOK MDS D51 Rev 06 and relevant standards for DMV 25.7N. Source: DMV_ST...

Open

2511

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

2512

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

2513

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-...

Open

2514

5.2

AI

No

add date

100% hydrostatic or non-destructive electric (EC/UT) testing per ASTM A999 is confirmed, but there is no explicit confirmation of compliance with the additional NDE requirements of NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782. Standard NDE capabili...

Open

2515

5.2

AI

No

add date

No provided documentation explicitly states that any indication greater than the calibration notch is considered a defect requiring rejection or repair of pipe/tubing, nor confirms standard NDE practices for the specified OD. Source: DMV_STANDARD_BOO...

Open

2516

6.0

AI

No

add date

Dimensional tolerances for the requested pipe are per ASTM A790/A999 as specified in the inquiry and supporting documents, with no override stated by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - ...

Open

2517

7.0

AI

No

add date

Finished pipes are required to be white pickled or bright annealed, which is explicitly specified in both ASTM A790 (section 6.1.3) and NORSOK MDS D51 Rev 06 (§13). Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2518

8.0

AI

No

add date

Marking per ASTM A790 and standard methods (indelible ink, vibro-etching) include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Certification per EN 10204 3.1 provides supporting details. Source: 02-04-03 ...

Open

2519

9.0

AI

No

add date

Weld repairs are not acceptable per NORSOK MDS D51 Rev 06 (§13, §14) for ASTM A790 DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2520

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

2521

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

2522

10.1

AI

No

add date

Supplier is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the requirement for qualification for the specif...

Open

2523

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

2524

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

2525

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if transverse is not p...

Open

2526

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2527

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive te...

Open

2528

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the item table and confirmed by the digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, Digest NORSOK...

Open

2529

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N but not to ISO 17782; no evidence provided for QTR/MPCR availability or full compliance with both standards as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06....

Open

2530

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

2531

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2532

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed by heat analysis with supplier certification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Dige...

Open

2533

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

2534

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

2535

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and per 100 pieces, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

2536

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions. For NPS 8 (...

Open

2537

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with mechanical properties meeting Table 4 requirements; hardness testing is also performed and results are provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

2538

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

2539

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness requirements for transverse specimens. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destru...

Open

2540

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition requirements and PRE ≥ 40 as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03...

Open

2541

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

2542

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

2543

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

2544

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

2545

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

2546

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

2547

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

2548

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

2549

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781, with specified etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact a...

Open

2550

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

2551

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided; compliance cannot be confirmed based on available information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard pla...

Open

2552

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, chemical composition, ferrite content, and corrosion/impact requirements. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

2553

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781, G48 Method A, as specified in NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2554

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

2555

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed after all mechanical processing, heat treatments, and straightening, with acceptance of ASTM E213 implying compliance with calibration notch requirements. Sou...

Open

2556

3.2

AI

No

add date

Solution annealing followed by accelerated cooling per ASTM A790 is confirmed; manufacturing process and furnaces are qualified per NORSOK M-650/ISO 17782; free circulation of heating/cooling media is ensured by compliance with these standards. Sourc...

Open

2557

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially addressed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are fulfilled. For the requested OD (219.1 mm), eddy current testing ...

Open

2558

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor that this acceptance criterion is applied in practice for the specified product...

Open

2559

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standards (ASTM A999), with OD, WT, and ovality tolerances confirmed for the requested dimensions. No deviations or overrides by TechnipFMC are indicated. Source: DMV_STANDARD_BOOK...

Open

2560

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: ASTM A790, NORSOK MDS D51 Rev 6

Open

2561

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring traceability as specified. Source: DMV_STANDARD_BOOK/02-0...

Open

2562

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2563

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system within the EEA, with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

2564

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers as specified in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

2565

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

2566

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and specification section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

2567

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is issued and includes all required information per ASTM A790 and NORSOK M-630, validated by Quality Control and compliant with specification requirements. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, 14-03 - Ce...

Open

2568

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive test...

Open

2569

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 Rev. 6, with all relevant mechanical, chemical, and testing requirements addressed. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_...

Open

2570

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2571

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of availability of QTR/MPCR documentation for review by TechnipFMC as required by the specification. Source: DMV_STANDARD_BOOK/0...

Open

2572

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N within specified wall thickness limits, and the manufacturing process is qualified per NORSOK M-650 (or ISO 17782) with testing meeting NORSOK M-630 MDS D51 requirements. Source: DMV_STA...

Open

2573

3.1

AI

No

add date

AOD or equivalent refining is used for DMV 25.7N, and chemical analysis complies with Table 2 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS...

Open

2574

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the requested WT of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest ...

Open

2575

3.2

AI

No

add date

Solution annealing followed by accelerated cooling is performed in accordance with ASTM A790; manufacturing process and furnaces are qualified to NORSOK M-650; free circulation of heating/cooling media is ensured by compliance with these standards. S...

Open

2576

4.1

AI

No

add date

No document confirms that impact, tensile, hardness, corrosion testing, and microstructure examinations are performed for each heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STAND...

Open

2577

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as referenced for tensile test requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

2578

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no information on CVN impact testing, test directions, or sampling locations for CVN, corrosion, or microstructure as required in Table 3. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790...

Open

2579

4.2

AI

No

add date

Tensile testing is performed per ASTM A370, meeting the tensile and maximum hardness properties of Table 4. Hardness testing is also performed as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

2580

4.2

AI

No

add date

None of the provided documents confirm that the mechanical requirements for DMV 25.7N (tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, hardness max 310/300 HBW) are met. Mechanical property values are either not specified or d...

Open

2581

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the ordered pipe (NPS 8, 219.1mm OD, 18.26mm WT), as it exceeds the minimum wall thickness required for both standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-0...

Open

2582

4.3

AI

No

add date

Pipe dimensions allow for transverse and longitudinal impact testing at -46°C with required absorbed energy values; requirement is fulfilled. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

2583

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination per ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels; only grain size measurement for austenitic materials is discussed, and duplex grades ...

Open

2584

4.4.1

AI

No

add date

No information confirming the use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination is provided. Requirement not addressed in the relevant documents.

Open

2585

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

2586

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic phases; isolated phases are permitted if not homogeneously distributed and each is below 10 μm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

2587

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided or addressed in the relevant documents or comments. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03...

Open

2588

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at 400x minimum magnification with a scale bar and actual magnification if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02-04-03 -...

Open

2589

4.4.2

AI

No

add date

No relevant documentation addresses the reporting of centerline intermetallic stringers or acceptance based on CVN and corrosion test results if such stringers are present. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I.doc, DMV...

Open

2590

4.4.2

AI

No

add date

NORSOK MDS D41 Rev 06 and NORSOK MDS D51 Rev 06 allow isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not meet the stricter client requirement of zero tolerance for intermetallic phases/precipitat...

Open

2591

4.4.3

AI

No

add date

No evidence that ferrite content is measured per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781; only grain size measurement is addressed, not ferrite content determination or required methods. Source: DMV_STANDARD_BOOK/12 - Special Testing/1...

Open

2592

4.4.3

AI

No

add date

No acceptance criteria for micrographic examination are specified or confirmed for DMV 25.7N in the provided sources. Relevant documents discuss procedures and standards but do not provide required acceptance values or results for this grade. Source:...

Open

2593

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and fulfilled for DMV 25.7N in both referenced documents. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev...

Open

2594

4.5

AI

No

add date

Corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is not mentioned or evidenced in the provided documentation or specifications. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

2595

4.5

AI

No

add date

No explicit acceptance criteria for metallurgical properties are specified in the provided documents; only general references or headings are present without defined values or requirements for DMV 25.7N or the specific inquiry. Source: DMV_STANDARD_B...

Open

2596

4.5

AI

No

add date

Specification requires pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², matching the client's requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

2597

5.1

AI

No

add date

No information is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, D...

Open

2598

5.2

AI

No

add date

No evidence is provided confirming 100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10, nor the required reference notch specifications or timing after all processing steps. Source: DMV_STANDARD_BOOK/12 - Special Testing/12...

Open

2599

5.2

AI

No

add date

Dye penetrant testing is available for tube ends and bevels as per standard practice, and qualitative anti-mixing PMI is performed 100% on standard production, fulfilling the Non-Destructive Evaluation (NDE) acceptance criteria for the client inquiry...

Open

2600

5.2

AI

No

add date

No relevant document confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair for the specified pipe; NDE acceptance criteria and reject/repair policy are not explicitly sta...

Open

2601

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are per the applicable ASTM standards (A790/A999, A213/A1016, A268, A269, A312, A376, A511) for the specified dimensions, with no deviations or special instructions noted in the inquiry or specification....

Open

2602

7.0

AI

No

add date

Finished pipes are required to be white pickled or bright annealed according to both ASTM A790 and NORSOK MDS S01 specifications, directly fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-0...

Open

2603

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

2604

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 specifies that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK...

Open

2605

10.0

AI

No

add date

No evidence of an appropriate quality-assurance system (e.g., ISO 9001 certification by a competent EEA body with specific assessment for materials) is provided for the Montbard plant or manufacturer. Source: DMV_STANDARD_BOOK/14-01 - General informa...

Open

2606

10.1

AI

No

add date

No evidence that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body with specific assessment for materials as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Ce...

Open

2607

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling supplier qualification documentation per SIR1...

Open

2608

10.2

AI

No

add date

No evidence is provided that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205. No explicit mention of SIR205, traceability, or transmission process is found in the relevant documents or comments. Source:...

Open

2609

10.2

AI

No

add date

Material certificate is issued according to EN 10204 Type 3.1 and validated by Quality Control for mill inspection; certificate type and process meet the requirement. Source: 14-03 - Certification Montbard plant.doc

Open

2610

10.2

AI

No

add date

No provided documentation includes NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of required metallurgical and non-destructive tes...

Open

2611

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as required for 25 Cr Duplex stainless steel seamless pipes. Manufacturing is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest ...

Open

2612

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N but not to ISO 17782; no evidence of full qualification to both NORSOK M-650/ISO 17782 or availability of QTR/MPCR documentation as required by the specification. Source: DMV_STANDARD_...

Open

2613

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

2614

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2615

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

2616

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes meets requirements: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure, with specified thickness locations. Ordered pipe dimensio...

Open

2617

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and hardness testing per ASTM A790, with DMV 25.7N meeting the tensile and maximum hardness properties of Table 4 as required. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2618

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-0...

Open

2619

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible and fulfilled for the specified pipe dimensions (WT > 6mm). Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

2620

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse average/single values of 45 J/35 J, and longitudinal average/single values of 65 J/50 J if transverse is not possible. The...

Open

2621

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, with etching using 20-40% NaOH or KOH solution after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

2622

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

2623

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

2624

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781, with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STAND...

Open

2625

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

2626

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

2627

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10 µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully fulfilled. Source...

Open

2628

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard alignment. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

2629

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

2630

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02...

Open

2631

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor are roles and responsibilities defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montba...

Open

2632

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects is performed per ASTM E213 or ISO 10893-10 on the specified pipe dimensions, and acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12-02-03 - Ult...

Open

2633

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/NORSOK M-650/ISO 17782 are not fully addressed; standard NDE methods (EC, UT, hydrostatic) for the specified OD are only available at extra cost or require special arrangement at Montbard...

Open

2634

5.2

AI

No

add date

None of the relevant sources explicitly confirm that indications greater than the calibration notch are considered defects requiring rejection or repair as specified; acceptance criteria and handling of such indications are not detailed in the provid...

Open

2635

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no deviations stated by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 790-02.doc, DMV_STANDARD_BOOK/0...

Open

2636

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: ASTM A790, NORSOK MDS D51 Rev 6

Open

2637

8.0

AI

No

add date

Marking is performed according to ASTM A790 (§14) and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Diges...

Open

2638

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly prohibits weld repairs under 'Surface finish / Repairs of defects'. Source: Digest NORSOK MDS D51 Rev 06.docx

Open

2639

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

2640

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

2641

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV25.7N up to WT = 31.75 mm, covering the requested WT of 18.26 mm, and the EN 10204 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR num...

Open

2642

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

2643

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Cert...

Open

2644

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse absorbed energy (average/single) of 45 J/35 J, and longitudinal (if transverse not possible) of 65 J/50 J. The specified p...

Open

2645

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and actual metallurgical and non-destruct...

Open

2646

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2647

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782; no evidence of QTR/MPCR documentation availability. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2648

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N with wall thickness up to 31.75 mm (hot finished), and the manufacturing process is qualified per NORSOK M-650/ISO 17782 with testing per NORSOK M-630 MDS D51 rev. 6. Requested wall thickness (18.26 ...

Open

2649

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2650

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Chemical composition matches the requirement table and is confirmed by supplier certification and heat analys...

Open

2651

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

2652

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790; frequency for each test is '1/lot'. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

2653

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and explicit reference to Table 3 for tensile tests, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed...

Open

2654

4.1

AI

No

add date

Test sampling for seamless pipes per ASTM A790/NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations. Ordere...

Open

2655

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produc...

Open

2656

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) per NORSOK MDS D51 Rev 6 and ASTM A790 requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

2657

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness (>6mm), fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - ...

Open

2658

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with specified etchants after final polishing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

2659

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases is required, in accordance with ISO 17781 Appendix B, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

2660

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

2661

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

2662

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

2663

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 requires reporting of intermetallic stringers, with acceptance based on CVN and corrosion test results as specified. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2664

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is...

Open

2665

4.4.3

AI

No

add date

Ferrite content is checked per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content determination by these methods in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

2666

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

2667

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is fulfilled for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2668

4.5

AI

No

add date

No explicit confirmation or evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 will be performed or is fulfilled. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

2669

4.5

AI

No

add date

DMV 25.7N meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite; M-650 qualification...

Open

2670

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

2671

5.1

AI

No

add date

No information is provided regarding the qualification, certification, or roles and responsibilities of NDE personnel to ISO 9712 level II or III or equivalent standards. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Mon...

Open

2672

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is feasible for the specified pipe dimensions and supported as a standard. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

2673

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2674

5.2

AI

No

add date

NDE per ASTM A790 is feasible, but specific NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 NDE requirements are not addressed or qualified. For OD 219.1 mm, eddy current is not feasible, and hydrostatic/ultrasonic/dye penetrant tests are only ...

Open

2675

5.2

AI

No

add date

None of the relevant sources confirm that indications greater than the calibration notch are classified as defects requiring rejection or repair for the specified product and dimension; acceptance criteria are not explicitly stated or confirmed for N...

Open

2676

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A ...

Open

2677

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2678

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

2679

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly prohibits weld repairs under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2680

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

2681

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

2682

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified s...

Open

2683

10.2

AI

No

add date

No explicit confirmation that documentation traceable to the products and transmitted to TechnipFMC (SIR205) will be provided. Documentation types and certification are described, but transmission and traceability to TechnipFMC are not confirmed. Sou...

Open

2684

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

2685

10.2

AI

No

add date

Documentation does not provide the steel producer of the starting material; only the country of origin is stated. Other required items (NORSOK M-650/ISO 17782 identification, melting practice, heat number, chemical analysis, solution annealing detail...

Open

2686

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 -...

Open

2687

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spec...

Open

2688

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV25.7N up to WT = 31.75 mm, with manufacturing process qualified per NORSOK M-650/ISO 17782 and compliance with NORSOK M-630 MDS D51 Rev. 6. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06....

Open

2689

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is covered by compliance...

Open

2690

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

2691

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement for test specimens sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-...

Open

2692

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790/NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locat...

Open

2693

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 as specified for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

2694

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength 750 MPa, yield strength 550 MPa, elongation 25%, and maximum hardness 310 HBW as required by NORSOK MDS D51 Rev 6 and ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

2695

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions; wall thickness (18.26 mm) exceeds minimum requirements for transverse specimens. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Dest...

Open

2696

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with specified minimum absorbed energies for transverse and longitudinal directions. The pipe dimensions allow for both transverse and longitudinal Charpy testing as...

Open

2697

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with 20-40% NaOH or KOH solution after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

2698

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

2699

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

2700

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

2701

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

2702

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

2703

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: ASTM A790, NORSOK MDS D51 Rev 06

Open

2704

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases and/or precipitates when CVN testing cannot be completed, or they allow isolated precipitates, which does not meet the stricter client requirement of not permittin...

Open

2705

4.4.3

AI

No

add date

Ferrite content is determined per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement as specified.

Open

2706

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

2707

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in accordance with ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

2708

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) performed in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

2709

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

2710

4.5

AI

No

add date

Corrosion test for DMV 25.7N is performed per ISO 17781: G48 Method A at 50°C for 24 hours, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and DMV 25.7N complies with these requirements. Source: DMV_STANDARD_B...

Open

2711

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montb...

Open

2712

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within capability range. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02...

Open

2713

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed; only ASTM A790/A999 NDE is detailed, which may not meet NORSOK requirements. For OD 219.1 mm, eddy current testing is not feasible, hydrostatic and ultraso...

Open

2714

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor confirms that the required NDE will be performed as standard for the specified product and size....

Open

2715

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with OD, WT, and ovality tolerances confirmed for the requested size and no override specified in customer documentation. Source: DMV_STANDARD_BOOK/07-01 - Ge...

Open

2716

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2717

8.0

AI

No

add date

Marking is performed according to ASTM A790 (§14) and includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD...

Open

2718

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly prohibits weld repairs under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NOR...

Open

2719

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782, as required. No confirmation of QTR/MPCR availability. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2720

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

2721

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

2722

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified ...

Open

2723

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/...

Open

2724

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

2725

10.2

AI

No

add date

Most required documentation and certification details (NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, metallurgical and NDT results) are stated as included in th...

Open

2726

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by specification references and digest documentation. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/...

Open

2727

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability or full qualification to both standards as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

2728

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782. Requirement for manufacturer and process qualification, and meeting NORSOK M-630 MDS D51 ...

Open

2729

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2730

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PREN ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - ...

Open

2731

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

2732

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

2733

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and explicit reference to Table 3, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 ...

Open

2734

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51 and ASTM A790 is fulfilled for DMV 25.7N, including tensile (longitudinal or transverse), hardness, CVN (transverse, longitudinal if not possible), corrosion, and microstructure at specified thickne...

Open

2735

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

2736

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

2737

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the requested pipe dimensions, which exceed the minimum wall thickness required for transverse specimens. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished...

Open

2738

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements: Charpy V-notch testing at -46°C, minimum transverse average/single values of 45 J/35 J, longitudinal average/single values of 65 J/50 J if transverse not possible, and sub-size reduct...

Open

2739

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, using 20-40% NaOH or KOH solution for etching after final polishing, fulfilling the requirement for metallographic preparation and examination and sp...

Open

2740

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

2741

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

2742

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included noting and recording the presence and location of intermetallic phases. Source: DMV_STAND...

Open

2743

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos including actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

2744

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

2745

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_BOOK/0...

Open

2746

4.4.3

AI

No

add date

Ferrite content is determined per ISO 17781 using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

2747

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 at ≥400X magnification, with etching to detect intermetallic phases, nitrides, and carbides. Structure must be basically free from intermetallic precipitates; isolated precipitates allowed if not ...

Open

2748

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

2749

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

2750

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, chemical composition, ferrite content, and corrosion/impact requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

2751

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A @ 50°C, 24h) requires no pitting at 20X magnification and weight loss < 1.0 g/m²; DMV 25.7N complies with both requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

2752

5.1

AI

No

add date

No evidence is provided confirming NDE personnel are qualified and certified to ISO 9712 level II or III, nor are their roles and responsibilities defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Mo...

Open

2753

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, which are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-0...

Open

2754

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially addressed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are met. For the requested OD (219.1 mm), eddy current and ultrasonic...

Open

2755

5.2

AI

No

add date

No provided documentation explicitly states that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor confirms standard NDE application for the specified dimension at Montbard. Source: DMV_STANDA...

Open

2756

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are confirmed to be per the applicable ASTM standard, with no deviations or special tolerances stated in the TechnipFMC part report or drawing. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_S...

Open

2757

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: ASTM A790 digest, NORSOK MDS D51 Rev 6 digest.

Open

2758

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot, with mandatory marking of heat number and DMV lot number using approved methods. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOO...

Open

2759

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 explicitly states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2760

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

2761

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers as specified in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

2762

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

2763

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 manufacturing summary or QTR number, are provided and fulfill the requirement for documentation traceable to the products and trans...

Open

2764

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, including reference notches as specified, and pipe dimensions are within machine capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV ...

Open

2765

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification summary. Source: DMV_STANDARD_BOOK...

Open

2766

10.2

AI

No

add date

Order-specific documentation and certification details required by the specification—such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and r...

Open

2767

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, DMV_STANDARD_B...

Open

2768

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N but not to ISO 17782; no evidence of QTR/MPCR availability for review as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2769

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

2770

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with the specified requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2771

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2772

3.2

AI

No

add date

Solution annealing followed by accelerated cooling per ASTM A790 is confirmed; manufacturing process and furnaces are qualified per NORSOK M-650/ISO 17782; free circulation of heating/cooling media is implicit in compliance with these standards. Sour...

Open

2773

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

2774

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and explicit reference to Table 3 for tensile tests, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed...

Open

2775

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), corrosion, and microstructure tests at specified locations per NORSOK MDS D51/ASTM A790. For NPS 8 (...

Open

2776

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, with required properties (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and maximum hardness verified; DMV 25.7N complies with these requirements. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

2777

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) per NORSOK MDS D51 Rev 6 and ASTM A790 requirements for Table 4 mechanical properties. Source: DMV_STANDAR...

Open

2778

7.0

AI

No

add date

Finished pipes are required to be white pickled or bright annealed by both ASTM A790 and NORSOK MDS S01 standards, fulfilling the requirement. Source: ASTM A790, NORSOK MDS S01

Open

2779

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for NPS 8 pipe with 18.26 mm wall thickness, exceeding the minimum required for transverse specimens. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testin...

Open

2780

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse average/single values of 45 J/35 J, longitudinal average/single values of 65 J/50 J if transverse not possible, and sub-siz...

Open

2781

4.4.1

AI

No

add date

Micrographic examination and etching for intermetallic phases and ferrite balance are performed as per ISO 17781, using the specified etchants after final polishing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

2782

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH solution for micrographic examination to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

2783

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

2784

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

2785

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

2786

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

2787

4.4.2

AI

No

add date

NORSOK MDS D51 Rev 06 allows isolated intermetallic precipitates below 10μm if not distributed over the whole specimen, but does not prohibit all intermetallics/precipitates when CVN testing cannot be completed, as required by the client specificatio...

Open

2788

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781 using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for measurement per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STAND...

Open

2789

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, including etching methods, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impac...

Open

2790

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is specified and confirmed for DMV 25.7N as per ISO 17781/ASTM E1245 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

2791

4.5

AI

No

add date

Corrosion testing is performed per ASTM G48 Method A (50°C, 24h) in accordance with ISO 17781, with criteria and procedure detailed, confirming compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

2792

4.5

AI

No

add date

DMV 25.7N seamless pipe fulfills ASTM A790 and NORSOK MDS D51 Rev 6 metallurgical acceptance criteria, including destructive, micrographic, corrosion tests, ferrite content, and heat treatment, with M-650 qualification for the specified grade and wal...

Open

2793

3.1

AI

No

add date

AOD or equivalent steel refining is required for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Di...

Open

2794

4.5

AI

No

add date

DMV 25.7N meets the pitting corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours, with no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

2795

5.1

AI

No

add date

No information is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destru...

Open

2796

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

2797

5.2

AI

No

add date

NDE per ASTM A790 is partially addressed with hydrostatic or EC/UT testing, but there is no explicit evidence of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements. For OD 219.1 mm, eddy current testing is ...

Open

2798

5.2

AI

No

add date

No explicit confirmation that NDE acceptance criteria require rejection or repair of indications greater than the calibration notch; NDT feasibility for the requested size is not confirmed as standardly available at Montbard. Source: DMV_STANDARD_BOO...

Open

2799

6.0

AI

No

add date

Dimensional tolerances are applied per ASTM A790 (A999) standard for the specified size, with no overriding customer specification referenced. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances accordin...

Open

2800

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2801

8.0

AI

No

add date

Marking is performed per ASTM A790 §14 and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

2802

9.0

AI

No

add date

Weld repairs are explicitly not acceptable as stated in NORSOK MDS D51 Rev 06, §14 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK...

Open

2803

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

2804

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

2805

10.1

AI

No

add date

Supplier is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, and QTR number is included in the certificate, fulfilling the requirement for NORSOK M-650/ISO 17782 qualification documentation for the specified size and pro...

Open

2806

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/...

Open

2807

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

2808

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching for intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and examination in accordance ...

Open

2809

10.2

AI

No

add date

No source provides all required documentation and certification details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and full test results. Th...

Open

2810

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified up to the required wall thickness....

Open

2811

1.0

AI

No

add date

Manufacturing is stated to follow MDS-650 (ISO 17782) qualified procedures, but there is no explicit confirmation of supplier qualification to NORSOK M-650/ISO 17782 for the exact product supplied or availability of the full Qualification Test Record...

Open

2812

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

2813

3.1

AI

No

add date

AOD or equivalent steel refining is required for 100% of production and the chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 -...

Open

2814

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed by heat analysis and supplier certification for DMV material. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

2815

3.2

AI

No

add date

Solution annealing followed by accelerated cooling is performed per ASTM A790; manufacturing and furnaces are qualified per NORSOK M-650/ISO 17782; free circulation of heating/cooling media is ensured by compliance with these standards. Source: DMV_S...

Open

2816

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

2817

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, directly referencing Table 3 for sampling as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM ...

Open

2818

4.1

AI

No

add date

Test sampling for seamless pipes per ASTM A790 and NORSOK, including tensile (longitudinal or transverse), hardness, CVN (transverse), and corrosion/microstructure at specified thickness locations, is fulfilled. Pipe dimensions allow transverse CVN s...

Open

2819

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and the material meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dige...

Open

2820

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 06 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

2821

4.3

AI

No

add date

Charpy V-notch testing is performed in accordance with ISO 148-1 (striker radius 8 mm) and ASTM standards for the specified pipe dimensions, with acceptance criteria and frequency defined. Requirement is fulfilled for wall thickness and standards spe...

Open

2822

4.3

AI

No

add date

Impact testing at -46°C with minimum transverse average/single values of 45 J/35 J and longitudinal average/single values of 65 J/50 J is specified; reduction factors for sub-size specimens are included, matching all requirements exactly. Source: DMV...

Open

2823

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782; no confirmation of QTR/MPCR documentation availability. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2824

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

2825

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

2826

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

2827

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

2828

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

2829

4.4.2

AI

No

add date

Microstructure is required to be 'basically free from intermetallic precipitates,' but isolated precipitates below 10μm are permitted, which does not fully meet the requirement that intermetallic phases and/or precipitates are not permitted if CVN te...

Open

2830

4.4.3

AI

No

add date

Ferrite content is determined per ISO 17781 using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245, performed in accordance with ISO ...

Open

2831

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

2832

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

2833

4.5

AI

No

add date

Corrosion testing is performed per ASTM G48 Method A (50°C, 24h) in accordance with ISO 17781, with criteria and procedure detailed, confirming compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

2834

4.5

AI

No

add date

DMV 25.7N meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782 qualification, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite conten...

Open

2835

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781: G48 Method A, meeting 'No pitting at 20X magnification' and 'Weight loss < 1.0 g/m².' Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2836

5.1

AI

No

add date

No information is provided regarding the qualification, certification, or defined roles and responsibilities of NDE personnel to ISO 9712 level II or III or equivalent. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12...

Open

2837

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is performed after all mechanical processing, heat treatments, and straightening, and the equipment accommodates the specified pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Te...

Open

2838

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

2839

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, D...

Open

2840

5.2

AI

No

add date

NDE per ASTM A790 is partially aligned with available hydrostatic, EC, or UT testing, but there is no explicit evidence of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782. For OD 219.1 mm, EC and UT are only available at extra co...

Open

2841

5.2

AI

No

add date

None of the relevant documents explicitly state that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair of the pipe or tubing, nor do they confirm that the required NDE will be perform...

Open

2842

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed as per the applicable ASTM standard for ASTM A790 pipe, with no stated deviations or overrides by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07...

Open

2843

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSO...

Open

2844

8.0

AI

No

add date

Marking is performed according to ASTM A790 (§14) and includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD...

Open

2845

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable.' Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2846

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

2847

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

2848

10.1

AI

No

add date

Supplier is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the requirement for qualification for the specif...

Open

2849

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

2850

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 manufacturing summary/QTR number). Source: DMV_STANDARD_BOO...

Open

2851

10.2

AI

No

add date

No document provides all required details. EN 10204 3.1 certificates are stated to include NORSOK M-650/ISO 17782 identification, QTR number, steel melting practice, refining method, heat treatment condition, heat number, chemical and metallurgical t...

Open

2852

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by specification references and digest documentation. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV...

Open

2853

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat, confirming conformity to the required ...

Open

2854

3.2

AI

No

add date

Manufacturing process is qualified to NORSOK M-650; solution annealing followed by accelerated cooling per ASTM A790 is standard; furnace compliance and free circulation of heating/cooling media are ensured by qualification and standard practice. Sou...

Open

2855

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

2856

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

2857

4.1

AI

No

add date

Test sampling for seamless pipes per ASTM A790/NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure at specified thickness locations. Ordered pip...

Open

2858

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, with DMV 25.7N meeting the required tensile (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NO...

Open

2859

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required by NORSOK MDS D51 Rev 6 and ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

2860

4.3

AI

No

add date

Charpy V-notch impact testing is performed in accordance with ISO 148-1 (via ISO 17781) and is feasible for the specified pipe dimensions, meeting the requirement for testing per ASTM A370, ASTM A1058, or ISO 148-1 and acceptance criteria per Table 5...

Open

2861

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact test requirements: Charpy V-notch at -46°C, minimum average/single values of 45 J/35 J (transverse) and 65 J/50 J (longitudinal if transverse not possible). Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

2862

4.4.1

AI

No

add date

Micrographic examination and etching for intermetallic phases and ferrite balance are performed as per ISO 17781, using the specified etchants after final polishing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

2863

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is required for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

2864

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

2865

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

2866

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

2867

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

2868

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

2869

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm if not distributed over the whole specimen, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry ...

Open

2870

4.4.3

AI

No

add date

Ferrite content is determined per ISO 17781 using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

2871

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

2872

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2873

4.5

AI

No

add date

Corrosion testing is performed per ASTM G48 Method A (50°C, 24h) in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

2874

4.5

AI

No

add date

DMV 25.7N seamless pipe fulfills ASTM A790 base requirements and all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure tests. Source: DMV_STANDARD_BOOK/02-02-01 Diges...

Open

2875

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, meeting the criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

2876

5.1

AI

No

add date

No information is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destru...

Open

2877

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available after all processing steps, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV...

Open

2878

5.2

AI

No

add date

NDE per ASTM A790 is technically possible for the requested OD and length, but eddy current is not feasible, and hydrostatic/ultrasonic require extra cost and special consultation. Full-length dye penetrant testing is only available on request and no...

Open

2879

5.2

AI

No

add date

No available documentation explicitly confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that NDE is performed as standard for the specified dimension at Montbard. Source: DMV_STANDA...

Open

2880

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are confirmed to be per the applicable ASTM standard, with no customer override specified. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances acco...

Open

2881

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2882

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

2883

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 §14 states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: Digest NORSOK MDS D51 Rev 06.docx

Open

2884

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

2885

10.1

AI

No

add date

Supplier is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, with certification including NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the qualification requirement for the specified...

Open

2886

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

2887

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided, including all information required by ASTM A790 and NORSOK M-630, and validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certifica...

Open

2888

10.2

AI

No

add date

Documentation and certification requirements such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and results of all required metallurgical and non-destructive te...

Open

2889

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, including all relevant mechanical, chemical, and testing requirements. Source: DMV_STANDARD_BOOK/02-03-01 -...

Open

2890

1.0

AI

No

add date

No evidence of supplier qualification to NORSOK M-650/ISO 17782 or availability of QTR/MPCR documentation is provided in the relevant documents. Certification and inspection references do not address this requirement. Source: DMV_STANDARD_BOOK/02-04-...

Open

2891

3.0

AI

No

add date

MST-Tubes F is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 (or ISO 17782), meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

2892

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and DMV 25.7N complies with the required chemical analysis per the specification table. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-0...

Open

2893

3.1

AI

No

add date

DMV 25.7N (UNS S32760) is manufactured according to NORSOK M-650 qualified procedures, with MST-Tubes F accredited for UNS S32760/DMV25.7N up to WT = 31.75 mm, covering the requested WT of 18.26 mm. Existing QTR/MPCR signed off in compliance with M-6...

Open

2894

3.2

AI

No

add date

Solution annealing followed by water quenching is performed per ASTM A790, with furnaces and process qualified to NORSOK M-650. Pipes are arranged to ensure free circulation of heating and cooling media during heat treatment, including accelerated co...

Open

2895

4.1

AI

No

add date

No provided document confirms that impact, tensile, hardness, corrosion testing, and microstructure examinations are performed for each heat and heat treatment lot as defined in ASTM A790. Testing frequency and lot-based compliance are not explicitly...

Open

2896

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as referenced for tensile test requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

2897

4.1

AI

No

add date

Transverse CVN specimens are feasible for the specified pipe dimensions, and tensile and CVN test directions per ASTM A790 are fulfilled for seamless pipes as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc, D...

Open

2898

4.2

AI

No

add date

No provided document confirms tensile testing per ASTM A370 or ISO 6892-1 and compliance with the tensile and maximum hardness properties of Table 4 for DMV 25.7N. Source: DMV_STANDARD_BOOK/01-01-02 SMST-F Summary of grades.docx, DMV_STANDARD_BOOK/02...

Open

2899

4.2

AI

No

add date

No provided source confirms the required mechanical properties for DMV 25.7N. NORSOK MDS D41 specifies lower tensile (620 MPa) and yield (450 MPa) strengths than required. No source provides the required values for tensile strength (≥750 MPa), yield ...

Open

2900

4.3

AI

No

add date

No evidence that Charpy V-notch testing will be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1, or that results will meet Table 5 requirements; only feasibility rules are mentioned without confirmation of compliance or testing execu...

Open

2901

4.3

AI

No

add date

Impact testing at -46°C with specified absorbed energy values is feasible and can be fulfilled for pipe with 18.26mm wall thickness; transverse specimens are possible for NPS 8 at this thickness. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for h...

Open

2902

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination of 25 Cr Duplex stainless steels per ISO 17781 or the specified etching procedures; the available document only addresses grain size measurement for austenitic materials ...

Open

2903

4.4.1

AI

No

add date

Micrographic examination requires etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produc...

Open

2904

4.4.2

AI

No

add date

No provided documentation addresses the microstructure requirement regarding intermetallic phases or their maximum dimension and distribution as specified by the client requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STA...

Open

2905

4.4.2

AI

No

add date

No information or procedures are provided regarding the detection, recording, or micrographic documentation (at 400x or higher) of intermetallic phases; only grain size measurement is discussed. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examina...

Open

2906

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

2907

4.4.2

AI

No

add date

No provided documents address the detection, reporting, or acceptance criteria for centerline intermetallic stringers, nor do they reference CVN or corrosion test results in this context. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in...

Open

2908

4.4.2

AI

No

add date

Microstructure requirements in relevant NORSOK digests allow isolated intermetallic precipitates below 10µm, which does not meet the stricter client requirement of zero tolerance for intermetallic phases/precipitates if CVN testing cannot be complete...

Open

2909

4.4.3

AI

No

add date

No information is provided confirming ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781; only grain size measurement is discussed, not ferrite content determination. Source: DMV_STANDARD_BOOK/12 - Special Testing/...

Open

2910

4.4.3

AI

No

add date

No acceptance criteria or requirements for micrographic examination or metallurgical properties are specified for DMV 25.7N in the provided documents. Grain size examination is not applicable to duplex/super-duplex stainless steels, and micrographic ...

Open

2911

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2912

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and fulfilled for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D41 Re...

Open

2913

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) performed in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

2914

4.5

AI

No

add date

No acceptance criteria for metallurgical properties are specified for DMV 25.7N in the provided documentation. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

2915

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with criteria: no pitting at 20X magnification and weight loss < 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

2916

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_...

Open

2917

5.2

AI

No

add date

No explicit confirmation of 100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10, nor reference notch criteria as specified, is provided in the available documentation. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - ...

Open

2918

5.2

AI

No

add date

100% qualitative anti-mixing PMI checks are performed on standard production using appropriate instruments, fulfilling the NDE/PMI requirement. Quantitative PMI can be provided if specified by the customer specification. Source: DMV_STANDARD_BOOK/12 ...

Open

2919

5.2

AI

No

add date

ASTM A790 requires NDE per ASTM A999, which mandates that any indication greater than the calibration notch is considered a defect and the pipe/tube must be rejected or repaired, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

2920

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are per the applicable ASTM standards (A790/A999, A213/A1016, A268, A269, A789, A312, A376, A511) for the requested product dimensions, with no deviations or special tolerances indicated in the customer ...

Open

2921

7.0

AI

No

add date

Finished pipes are required to be white pickled or bright annealed, which is directly specified in both ASTM A790 and NORSOK MDS S01 standards for surface condition and finish. Source: ASTM A790 digest, NORSOK MDS S01 digest.

Open

2922

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

2923

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 specifies that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

2924

10.0

AI

No

add date

No evidence of ISO 9001 certification or assessment by a competent EEA body for the material manufacturer is provided in the relevant documents. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Certification Montba...

Open

2925

10.1

AI

No

add date

No confirmation that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification or that documentation will be submitted to TechnipFMC for approval. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14...

Open

2926

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, demonstrating qualification for the size and product f...

Open

2927

10.2

AI

No

add date

No provided documentation confirms transmission of product-traceable documentation (SIR205) to TechnipFMC or evidence of ISO 9001 certification by a competent EEA body for the Montbard plant or specific order. Source: DMV_STANDARD_BOOK/14-01 - Genera...

Open

2928

10.2

AI

No

add date

Material certificate is issued per EN 10204 Type 3.1 and validated by Quality Control; specification references ASTM A790 and NORSOK M-630, implying inclusion of required information. Source: 14-03 - Certification Montbard plant.doc

Open

2929

10.2

AI

No

add date

None of the provided sources contain the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or ...

Open

2930

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by specification references and digest documentation. Source: Item Table, Digest NORSOK MDS D51 Rev 06.docx

Open

2931

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N but not to ISO 17782; no evidence of QTR/MPCR availability or full qualification per both standards as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2932

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

2933

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2934

3.1

AI

No

add date

Chemical composition for S32760 matches Table 2 requirements and is confirmed to conform per heat analysis. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

2935

3.2

AI

No

add date

Solution annealing followed by accelerated cooling per ASTM A790 is confirmed; manufacturing process and furnaces are qualified per NORSOK M-650/ISO 17782; free circulation of heating/cooling media is implicit in compliance with these standards. Sour...

Open

2936

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot, with 'lot' defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

2937

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and explicit reference to Table 3 for tensile tests, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed...

Open

2938

4.1

AI

No

add date

Test sampling requirements for seamless pipes per NORSOK MDS D51/ASTM A790, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified thickness location...

Open

2939

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and maximum hardness properties of Table 4. Hardness testing is also performed per ASTM...

Open

2940

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets the minimum mechanical requirements: yield strength ≥ 550 MPa, tensile strength ≥ 750 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW, as specified in NORSOK MDS D51 Rev 6 and ASTM A790 for S32760. Source: DMV_STANDARD_BOOK...

Open

2941

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the requested pipe dimensions (WT 18.26mm > minimum required), fulfilling the requirement. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

2942

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if transverse...

Open

2943

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, including etching to detect intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

2944

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

2945

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

2946

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

2947

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

2948

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

2949

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size. Source: DMV_STANDARD_BOOK/02-04-03 - Di...

Open

2950

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_ST...

Open

2951

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosio...

Open

2952

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in accordance with ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

2953

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided; compliance cannot be confirmed based on available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard p...

Open

2954

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including destructive, micrographic, ferrite, corrosion tests, heat treatment, and manufacturing process requirements. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

2955

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781 G48 Method A, as specified in NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

2956

5.1

AI

No

add date

No information is provided regarding the qualification, certification, or defined roles and responsibilities of NDE personnel to ISO 9712 level II or III or equivalent. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12...

Open

2957

5.2

AI

No

add date

NDE per ASTM A790 is partially feasible at Montbard for the requested OD and length, but eddy current and ultrasonic testing are only available at extra cost and not standard; eddy current is not feasible for this OD per the feasibility table. There ...

Open

2958

5.2

AI

No

add date

None of the referenced documents explicitly confirm that indications greater than the calibration notch are considered defects requiring rejection or repair, nor do they confirm feasibility of the required NDE for the specified dimensions at Montbard...

Open

2959

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no evidence of override or deviation in the customer specification. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01...

Open

2960

7.0

AI

No

add date

ASTM A790 (6.1.3) and NORSOK MDS D51 (§13) both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2961

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-0...

Open

2962

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

2963

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

2964

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

2965

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size ...

Open

2966

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and specification section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

2967

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 manufacturing summary/QTR number). Source: DMV_STANDARD_BOO...

Open

2968

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all specified metallurgical and non-destruc...

Open

2969

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and are M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK...

Open

2970

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2971

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

2972

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2973

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

2974

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

2975

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

2976

4.1

AI

No

add date

Test specimens sampling is defined according to Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, fulfilling the requirement for outlined sampling procedures. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

2977

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51 and ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, longitudinal if not possible), corrosion, and microstructure tests are performed at specified thickness l...

Open

2978

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

2979

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

2980

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the requested pipe dimensions, which exceed the minimum wall thickness required for transverse specimens in both ASTM and ISO standards. Source: DMV_STANDARD_BOOK/12 - Spe...

Open

2981

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse absorbed energy (average/single) of 45 J/35 J, and longitudinal (if transverse not possible) of 65 J/50 J. The specified p...

Open

2982

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, with etching using 20-40% NaOH or KOH solution after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

2983

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

2984

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

2985

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

2986

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

2987

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

2988

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size. The requirement is not fully fulfilled by the ...

Open

2989

4.4.3

AI

No

add date

Ferrite content is determined per ASTM E562 or ASTM E1245, performed in accordance with ISO 17781, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK...

Open

2990

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 at ≥400X magnification, with etching to detect intermetallic phases, nitrides, and carbides. Structure must be free from intermetallic precipitates except isolated ones <10µm, and carbides/nitride...

Open

2991

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

2992

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

2993

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including PRE, tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

2994

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781 (G48 Method A @ 50°C, 24h). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Diges...

Open

2995

5.1

AI

No

add date

No information is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feas...

Open

2996

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, with pipe dimensions within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

2997

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT) is confirmed, but compliance with NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782 is not demonstrated. Eddy current testing is not feasible for OD 219.1 mm, and feasibility for required NDE methods is no...

Open

2998

5.2

AI

No

add date

No provided documentation explicitly states that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor confirms standard NDE application for the requested dimensions at Montbard. Source: Digest AS...

Open

2999

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standards (ASTM A999), with no override by TechnipFMC. OD, WT, and ovality tolerances for the requested dimensions are confirmed as per ASTM standard. Source: DMV_STANDARD_BOOK/07-...

Open

3000

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORS...

Open

3001

8.0

AI

No

add date

Marking per ASTM A790 and mandatory inclusion of heat number and DMV lot number ensure full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standard mar...

Open

3002

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

3003

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

3004

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

3005

10.1

AI

No

add date

Supplier MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the requirement for qualification demonstration. Sou...

Open

3006

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/...

Open

3007

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is issued and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control for mill inspection and referencing the relevant standards and qualification summary. Source: DMV_STANDARD_BOOK/...

Open

3008

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of metallurgical and non-destructive testin...

Open

3009

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_...

Open

3010

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782, as required. No evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3011

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

3012

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3013

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3014

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

3015

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

3016

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for sampling requirements, fulfilling the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03...

Open

3017

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure tests are performed at specified thickness lo...

Open

3018

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370, and material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORS...

Open

3019

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required by NORSOK MDS D51 Rev 06 and ASTM A790 for Table 4 mechanical properties. Source: DMV_STANDARD...

Open

3020

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the requested pipe dimensions, which exceed the minimum wall thickness required for transverse specimens. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructiv...

Open

3021

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if transverse...

Open

3022

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 using 20-40% NaOH or KOH solution after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

3023

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dige...

Open

3024

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

3025

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

3026

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

3027

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

3028

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, but does not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed, as required by the client specification. Source: DMV_STANDARD_BOOK...

Open

3029

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

3030

3.1

AI

No

add date

Chemical composition for S32760 matches Table 2 requirements and is confirmed to conform per heat analysis. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

3031

4.4.3

AI

No

add date

Micrographic examination acceptance criteria are specified: structure must be basically free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides findings reported, and acceptance based on impact and corrosion test results....

Open

3032

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS ...

Open

3033

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

3034

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO ...

Open

3035

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

3036

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in...

Open

3037

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is fulfilled for the specified pipe dimensions and after all mechanical processing, heat treatments, and straightening operations. Source: DMV_STANDARD_BOOK/12 - Special T...

Open

3038

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/ISO 17782 are not fully addressed; standard NDE methods (EC, UT, hydrostatic) for the specified OD and length are only available at extra cost or require technical advisor consultation, a...

Open

3039

5.2

AI

No

add date

No provided source confirms that NDE acceptance criteria require rejection or repair for indications greater than the calibration notch, nor that such NDE is standardly feasible for the specified pipe dimension at Montbard. Source: Digest ASTM A 790....

Open

3040

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no deviations or overrides stated in the customer specification or part report/drawing. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - Gener...

Open

3041

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3042

8.0

AI

No

add date

Marking per ASTM A790 includes traceability to melt and heat treatment lot; marking methods (indelible ink, vibro-etching) ensure inclusion of heat number and DMV lot number for full traceability. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

3043

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly prohibits weld repairs under 'Surface finish / Repairs of defects'. Source: Digest NORSOK MDS D51 Rev 06.docx

Open

3044

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

3045

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system as specified in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 -...

Open

3046

4.5

AI

No

add date

DMV 25.7N meets the requirements for no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781 (G48 Method A @ 50°C, 24h). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dige...

Open

3047

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size ...

Open

3048

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

3049

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference). Source: DMV_STANDARD_BOOK/02-04-0...

Open

3050

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or specific metallurgical and non-destructive test result...

Open

3051

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, D...

Open

3052

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR availability. Requirement for qualification to both NORSOK M-650/ISO 17782 and documentation availability is not fulfilled...

Open

3053

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782. Requirement for manufacturer and process qualification, and meeting NORSOK M-630 MDS D51 ...

Open

3054

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3055

3.1

AI

No

add date

Chemical composition limits for UNS S32760 conform to Table 2 of ASTM A790 as required, with heat analysis and supplier certification provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A...

Open

3056

3.2

AI

No

add date

Solution annealing followed by accelerated cooling per ASTM A790 is confirmed; manufacturing process and furnaces are qualified per NORSOK M-650/ISO 17782; free circulation of heating/cooling media is implicit in compliance with these standards. Sour...

Open

3057

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot, with 'lot' defined according to ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

3058

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and pieces, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01...

Open

3059

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes per ASTM A790/NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure tests are performed at specified th...

Open

3060

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with required properties (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and maximum hardness per Table 4; DMV 25.7N meets these criteria. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

3061

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

3062

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the requested pipe dimensions, which exceed the minimum wall thickness required for transverse specimens. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructiv...

Open

3063

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if transverse...

Open

3064

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed according to ISO 17781, with specified etchants and electrolytic etching after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

3065

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution for micrographic examination to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

3066

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates allowed if not distributed over the whole specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

3067

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

3068

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

3069

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

3070

4.4.2

AI

No

add date

The available specifications allow isolated intermetallic precipitates below 10μm, but do not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed, as required by the client specification. Source: DMV_STANDARD_BO...

Open

3071

4.4.3

AI

No

add date

Ferrite content is checked per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for determination per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK...

Open

3072

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

3073

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

3074

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

3075

4.5

AI

No

add date

DMV 25.7N meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782 qualification, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite conten...

Open

3076

4.5

AI

No

add date

DMV 25.7N undergoes pitting corrosion testing per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD...

Open

3077

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

3078

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

3079

5.2

AI

No

add date

100% hydrostatic or NDE (EC or UT) testing per ASTM A999 is confirmed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE acceptance criteria are addressed. For OD 219.1 mm, eddy current testing i...

Open

3080

5.2

AI

No

add date

No provided documentation explicitly confirms that indications greater than the calibration notch are treated as defects and that such pipe/tubing is rejected or repaired, nor is there confirmation of standard NDE feasibility for the requested dimens...

Open

3081

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standards (ASTM A999), with no override by TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to AST...

Open

3082

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3083

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 (§14), requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring compliance with the requirement. Source: DMV_S...

Open

3084

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3085

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for a quality-assurance system with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Di...

Open

3086

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the required quality-assurance system for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

3087

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified ...

Open

3088

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

3089

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, M-650/ISO17782 manufacturing summary/QTR number). Source: DMV_STANDARD_BOOK/...

Open

3090

10.2

AI

No

add date

NORSOK M-650/ISO 17782 qualification, QTR/MPCR number, steel melting practice and refining method, and solution annealing details are referenced as standard or included in certificates, but the actual steel producer, heat number, full chemical (ladle...

Open

3091

3.2

AI

No

add date

Solution annealing followed by accelerated cooling per ASTM A790 is confirmed, with manufacturing and furnace qualification per NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is covered ...

Open

3092

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

3093

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

3094

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

3095

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source: DM...

Open

3096

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790, both requiring full traceability to melt and heat treatment lot. Marking methods (indelible ink, vibro-etching) include heat number and DMV lot number, ensuring traceability. Source: Dige...

Open

3097

10.1

AI

No

add date

Supplier is M-650 accredited for DMV25.7N up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

3098

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

3099

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

3100

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for sampling requirements, fulfilling the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03...

Open

3101

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations is fulfilled. For...

Open

3102

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

3103

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

3104

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, meeting the minimum wall thickness requirements of the standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing...

Open

3105

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact test requirements at -46°C: minimum transverse average 45 J, single 35 J; longitudinal average 65 J, single 50 J if transverse not possible. The specified pipe dimensions allow for transverse Charp...

Open

3106

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed according to ISO 17781, with electrolytic etching using 20-40% NaOH or KOH after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

3107

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH solution for micrographic examination to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

3108

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

3109

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

3110

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

3111

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

3112

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10 µm, but does not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed, as required by the client. Source: DMV_STANDARD_BOOK/02-04-03 - Digest ...

Open

3113

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

3114

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

3115

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification listing and digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Di...

Open

3116

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

3117

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

3118

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

3119

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

3120

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

3121

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

3122

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

3123

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within the machine's capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive...

Open

3124

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT) is confirmed, but compliance with specific NDE requirements of NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782 is not demonstrated. Eddy current testing is not feasible for the required OD, and hyd...

Open

3125

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor confirms that the required NDE methods and acceptance criteria are applied for ...

Open

3126

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standard, with no evidence of a deviation or special tolerance request in the customer specification. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_S...

Open

3127

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

3128

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produc...

Open

3129

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

3130

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

3131

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

3132

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

3133

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference. Source: DMV_STANDARD_BO...

Open

3134

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the spec...

Open

3135

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the client inquiry and confirmed by digest documents. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_...

Open

3136

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

3137

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but lacks ISO 17782 accreditation; no evidence provided for QTR/MPCR availability as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3138

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

3139

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

3140

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

3141

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

3142

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

3143

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

3144

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

3145

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3146

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

3147

5.2

AI

No

add date

100% of the pipes are subject to hydrostatic or EC/UT testing as per ASTM A999, fulfilling the NDE requirement per ASTM A790 and the specification context. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03...

Open

3148

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the specified pipe, with no deviations or special requirements indicated by the customer specification or TechnipFMC part report/drawing. Source: DMV_STANDARD_BOOK/07-01...

Open

3149

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782 as required; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3150

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3151

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Chemical limits match the requirement and are confirmed by supplier certification and heat analysis. So...

Open

3152

3.2

AI

No

add date

Solution annealing followed by accelerated cooling per ASTM A790 is confirmed; manufacturing process and furnace compliance with NORSOK M-650/ISO 17782 are met; free circulation of heating/cooling media is implicit in standard compliance. Source: DMV...

Open

3153

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot, with 'lot' defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

3154

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and lot definition, directly matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

3155

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per NORSOK MDS D51 and AS...

Open

3156

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-0...

Open

3157

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

3158

4.3

AI

No

add date

Charpy V-notch testing in accordance with ASTM A370 and ISO 148-1 is feasible for the specified pipe dimensions and meets the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - I...

Open

3159

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C, including minimum absorbed energy values and sub-size reduction factors. The specified pipe dimensions allow for required transverse and longitudinal Charpy V-notch t...

Open

3160

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with specified etchants for intermetallic phases and ferrite balance after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

3161

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

3162

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

3163

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

3164

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, reported at actual magnification and including a scale bar, if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - ...

Open

3165

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_ST...

Open

3166

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size, so the requirement is not fully me...

Open

3167

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

3168

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

3169

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as specified in NORSOK MDS D51 Rev 06 digest. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NOR...

Open

3170

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is fulfilled; neither standard nor test is mentioned or documented as performed. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant...

Open

3171

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3172

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

3173

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

3174

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed on the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - U...

Open

3175

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD, eddy current and ultrasonic testing are only available at extra cost and...

Open

3176

5.2

AI

No

add date

The available documents do not explicitly state that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, and standard NDE is not available for the requested OD at Montbard as specified...

Open

3177

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and ASTM A999 as required, with no overriding specifications indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A 376-02...

Open

3178

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be pickled or bright annealed, directly fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3179

4.1

AI

No

add date

Tensile test specimen sampling is performed according to Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/0...

Open

3180

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 (§14), requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring compliance with the requirement for traceabili...

Open

3181

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

3182

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

3183

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

3184

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness for the specified size and product form. Source: DMV_STANDARD_BO...

Open

3185

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

3186

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

3187

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. Other required ...

Open

3188

1.0

AI

No

add date

DMV 25.7N seamless pipe is confirmed as compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-...

Open

3189

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782 as required; no evidence provided for QTR/MPCR availability for review by TechnipFMC or full compliance with both standards as specified. Source: DMV_STANDARD_BOOK/02-04-03 - D...

Open

3190

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process follows M-650 (or ISO 17782) qualified procedures, fulfilling the requirement for manufacturer and process qualification per NORSOK M-...

Open

3191

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3192

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits and PREN requirements specified in Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 6. Heat analysis and supplier certification are performed per heat. Source: 02-03-01 - Digest A...

Open

3193

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

3194

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

3195

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

3196

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specifi...

Open

3197

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4, in compliance with NORSOK MDS D51. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

3198

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

3199

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests ...

Open

3200

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C (transverse: 45/35 J, longitudinal: 65/50 J) for thickness >6mm; the specified pipe dimensions allow for both transverse and longitudinal testing as required. Source:...

Open

3201

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

3202

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

3203

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

3204

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

3205

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

3206

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

3207

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

3208

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

3209

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

3210

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3211

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

3212

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

3213

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including chemical composition (PRE ≥ 40), mechanical properties, microstructure, ferrite content (35-60%), and corrosion resistance; manufacturing process i...

Open

3214

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02...

Open

3215

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destruct...

Open

3216

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is supported for the specified pipe dimensions after all processing steps. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultras...

Open

3217

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed; only ASTM A790/A999 NDE is detailed. For the required OD, eddy current testing is not standardly feasible at Montbard and requires special approval. Dye pe...

Open

3218

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair, and no evidence that the required NDE will be performed as specified for the requested dimensions and standards. Accept...

Open

3219

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding customer specification or drawing indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a ...

Open

3220

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3221

8.0

AI

No

add date

Marking per ASTM A790 §16 and plant procedures ensures mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSO...

Open

3222

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for DMV 25.7N seamless pipe, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3223

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

3224

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

3225

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification dem...

Open

3226

10.2

AI

No

add date

ISO 9001 certification is provided, and EN 10204 type 3.1 certificates ensure traceability and transmission of required documentation to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

3227

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630 for the product in question, validated by Quality Control and referenced in the relevant specifications and plant documentation. Source: DMV_...

Open

3228

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or full test results. Some documents c...

Open

3229

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

3230

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N (up to WT = 31.75 mm, cold finished up to WT = 10.925 mm), but not to ISO 17782 as required. No confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Dige...

Open

3231

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), with manufacturing and qualification testing meeting NORSOK M-630 MDS D51 Rev. 6 and M-650 (or ISO 17782) requirements. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

3232

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3233

3.1

AI

No

add date

DMV 25.7N (UNS S32760) chemical composition matches the requirements of Table 2 and complies with ASTM A790 and NORSOK MDS D51 Rev 06, including PREN ≥ 40 and all specified element limits. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, ...

Open

3234

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

3235

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

3236

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling as outlined in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

3237

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK M-630 MDS D51 Rev 6 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure tests are perform...

Open

3238

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and the material meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dige...

Open

3239

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 and ASTM A790 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

3240

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

3241

4.3

AI

No

add date

Charpy V-notch testing in accordance with ASTM A370 and ISO 148-1 is feasible for the specified pipe dimensions and can be performed as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03...

Open

3242

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -466C, with minimum absorbed energy values for transverse and longitudinal directions, and the specified pipe dimensions allow for required transverse Charpy V-notch testing as per...

Open

3243

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

3244

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

3245

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

3246

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

3247

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with representative micrographs at or near mid-wall thickness included in the report at actual magnification and with a scale bar, if intermetallic phases are not detected. Sou...

Open

3248

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

3249

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

3250

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

3251

4.4.3

AI

No

add date

Microstructure examination is performed as per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at minimum 400X magnification. Structure must be basically free from intermetallic precipitates, with isolated precipitates a...

Open

3252

4.4.3

AI

No

add date

Ferrite content for DMV 25.7N is specified as 35% to 60%, meeting the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3253

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/...

Open

3254

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02...

Open

3255

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

3256

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712 or equivalent standard. Requirement is not fulfilled based on the ava...

Open

3257

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available after all mechanical processing, heat treatments, and straightening, and the equipment supports the specified pipe dimensions and standards. Source: DMV_STAND...

Open

3258

5.2

AI

No

add date

NDE per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 is not confirmed; only ASTM A790/A999 NDE is detailed. For the required OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/ultrasonic testing is only available at extra cost. F...

Open

3259

5.2

AI

No

add date

No evidence that NDE acceptance criteria require rejection or repair of indications greater than the calibration notch; feasibility for required NDE on OD 219.1 mm is not confirmed for Montbard plant. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-...

Open

3260

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790 referencing ASTM A999) for the requested pipe dimensions, with no override by TechnipFMC indicated in the provided context. Source: DMV_STANDARD_BOOK/07-01 - General information.d...

Open

3261

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3262

8.0

AI

No

add date

Marking is performed per ASTM A790 §14 and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

3263

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

3264

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

3265

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

3266

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

3267

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

3268

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

3269

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching by 20-40% NaOH or KOH and ferrite check as per ISO 17781, matching the requirement for metallographic preparation and examination and the specified etchants after final polishing. S...

Open

3270

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly prohibits weld repairs under 'Surface finish / Repairs of defects'. Source: Digest NORSOK MDS D51 Rev 06.docx

Open

3271

10.2

AI

No

add date

No specific documentation or evidence is provided for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution anneali...

Open

3272

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability is provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3273

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

3274

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3275

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PRE ≥ 40, as required by ASTM A790 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat to ensure compliance. Source: 02-03-01 - ...

Open

3276

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

3277

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

3278

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing the table for test specimen sampling as outlined in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

3279

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specified thickness loc...

Open

3280

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-0...

Open

3281

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

3282

4.3

AI

No

add date

Pipe wall thickness exceeds minimum required for Charpy V-notch testing; testing per ASTM A370 and ISO 148-1 is feasible and can be performed as specified. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

3283

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements: Charpy V-notch testing at -466C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal. The specified pipe d...

Open

3284

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3285

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

3286

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

3287

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

3288

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

3289

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

3290

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm if not distributed over the whole specimen, but the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. This stricte...

Open

3291

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 ...

Open

3292

4.4.3

AI

No

add date

Micrographic examination per ISO 17781 is specified, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impact ...

Open

3293

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

3294

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

3295

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content...

Open

3296

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

3297

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source: DM...

Open

3298

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed on the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - U...

Open

3299

1.0

AI

No

add date

Supplier is NORSOK M-650 accredited for DMV 25.7N but not accredited to ISO 17782 as required; no evidence provided for QTR/MPCR availability for review or full compliance with both standards for the exact product supplied. Source: DMV_STANDARD_BOOK/...

Open

3300

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3301

5.2

AI

No

add date

NDE per ASTM A790/A999 is detailed, but there is no explicit confirmation of compliance with NORSOK-specific NDE requirements. For the specified OD, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at extra co...

Open

3302

5.2

AI

No

add date

No provided documentation explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, and standard NDE methods for this requirement are either not feasible or only available at extr...

Open

3303

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding TechnipFMC specification indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A 376-0...

Open

3304

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number, lot number, and other traceable information, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORS...

Open

3305

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

3306

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

3307

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

3308

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number as required, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

3309

10.2

AI

No

add date

No provided document confirms that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205; only general references to certification and documentation are present without explicit fulfillment of the requirement...

Open

3310

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing the relevant standards as the basis for documentation. Source: DMV_STANDARD_BOOK/02-04-03 - D...

Open

3311

10.2

AI

No

add date

No source provides all required documentation and certification details for the specific order, including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and test...

Open

3312

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

3313

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782; no evidence of QTR/MPCR documentation availability. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3314

3.0

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process follows M-650 (or ISO 17782) qualified procedures; the product (WT = 18.26 mm) is within the accredited range and meets NORSOK M-630 MDS D51 ...

Open

3315

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3316

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed by supplier certification and heat analysis per ASTM A790 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dige...

Open

3317

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing and heat treatment qualified and performed in compliance with NORSOK M-650/ISO 17782. Free circulation of heating and cooling me...

Open

3318

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

3319

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling as outlined in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

3320

4.1

AI

No

add date

Test sampling for seamless pipes per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations are...

Open

3321

4.2

AI

No

add date

Tensile testing is performed at room temperature in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

3322

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

3323

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions (OD 219.1mm, WT 18.26mm) in both longitudinal and transverse directions as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - D...

Open

3324

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, with minimum absorbed energy values for transverse and longitudinal directions, and the specified pipe dimensions allow for required testing directions and specimen...

Open

3325

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

3326

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-...

Open

3327

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

3328

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50°C, 24h) in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

3329

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

3330

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

3331

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

3332

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fulfilled by the available ...

Open

3333

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

3334

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

3335

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

3336

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the listed standards or documents. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

3337

4.5

AI

No

add date

DMV 25.7N meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content. Source: DMV...

Open

3338

4.5

AI

No

add date

DMV 25.7N meets the pitting corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours, with no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

3339

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

3340

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 or ISO 10893-10 is confirmed as available for the specified pipe dimensions and after all processing steps. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destr...

Open

3341

5.2

AI

No

add date

There is no explicit evidence that NDE requirements per NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782 are addressed. Eddy current testing is not feasible for the required OD, and hydrostatic or ultrasonic testing is only available at extra cos...

Open

3342

5.2

AI

No

add date

No provided document explicitly states that any indication greater than the calibration notch is considered a defect requiring rejection or repair, and standard NDE is not available for the requested OD at Montbard. Source: DMV_STANDARD_BOOK/02-03-01...

Open

3343

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with OD, WT, and ovality tolerances confirmed for the requested dimensions. No deviations or special tolerances are specified in the customer request or Techn...

Open

3344

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSO...

Open

3345

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring traceability as specified. Source: DMV_STANDARD_BOOK/02-0...

Open

3346

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement for DMV 25.7N seamless pipe per ASTM A790 and NORSOK M-630 MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

3347

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

3348

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, meeting the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-0...

Open

3349

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

3350

10.2

AI

No

add date

ISO 9001 certification is provided and documentation traceable to the products, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO 17782 manufacturing summary or QTR number, is transmitted to TechnipFMC as required by SIR205. Source: DMV_S...

Open

3351

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, M-650/ISO17782 manufacturing summary/QTR number). Source: DMV_STANDARD_BOOK/...

Open

3352

10.2

AI

No

add date

Most required documentation and traceability elements (NORSOK M-650/ISO 17782 identification, QTR/MPCR number, steel producer, heat number, chemical analysis, solution annealing parameters, metallurgical and NDT results) are stated as included in the...

Open

3353

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification and digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest N...

Open

3354

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; full qualification to NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR is not confirmed. Source: DMV_STANDARD_BOOK/02...

Open

3355

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, fulfilling the requirement for manufacturer and process qualification and compliance with ...

Open

3356

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition conforms to Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3357

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed by heat analysis and supplier certification for DMV material. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

3358

3.2

AI

No

add date

Solution annealing followed by accelerated cooling per ASTM A790 is confirmed, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is implicit in compliance wi...

Open

3359

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot, with 'lot' defined according to ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

3360

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for sampling requirements, fulfilling the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03...

Open

3361

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes per ASTM A790/NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure tests at specified thickness locati...

Open

3362

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with tensile and hardness properties meeting Table 4 requirements for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3363

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets the minimum tensile strength (750 MPa), yield strength (550 MPa), elongation (25%), and maximum hardness (310 HBW) requirements per NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

3364

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness required for standard transverse specimens. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot...

Open

3365

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -46°C, with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal, including sub-size reduction factors. The sp...

Open

3366

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants after final polishing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

3367

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

3368

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

3369

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

3370

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar if intermetallic phases are not detected at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

3371

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

3372

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10μm, but does not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed, as required by the client specification. Source: DMV_STANDARD_BOOK/02-04-03 - D...

Open

3373

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

3374

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

3375

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3376

4.5

AI

No

add date

The applicable standards listed do not explicitly confirm corrosion testing per ASTM G48 Method 'A' (50°C, 24h) in accordance with ISO 17781; requirement not fulfilled. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

3377

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive, micrographic, corrosion tests, ferrite content, heat treatment, and manufacturing process requirements; plant is M-650 accredited for required wall...

Open

3378

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

3379

5.1

AI

No

add date

No information is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feas...

Open

3380

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, including reference notches as specified. Pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destru...

Open

3381

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially addressed with reference to hydrostatic or NDE (EC or UT) testing, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are fulfilled...

Open

3382

5.2

AI

No

add date

None of the relevant documents confirm that indications greater than the calibration notch are classified as defects requiring rejection or repair; NDE acceptance criteria are not explicitly detailed for this requirement or dimension at Montbard. Sou...

Open

3383

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 seamless pipe are per the applicable ASTM standard (ASTM A999), with no evidence of override in the customer specification or part report/drawing. Source: DMV_STANDARD_BOOK/07-01 - General informatio...

Open

3384

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that seamless pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3385

8.0

AI

No

add date

Marking per ASTM A790 includes heat and lot traceability; marking methods (indelible ink, vibro-etching) include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NO...

Open

3386

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states weld repairs are not acceptable, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-0...

Open

3387

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

3388

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body established within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

3389

10.1

AI

No

add date

Supplier MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, with certification including NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the requirement for qualification fo...

Open

3390

10.2

AI

No

add date

ISO 9001 certification is provided and documentation traceable to products, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 manufacturing summary or QTR number, is transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDA...

Open

3391

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

3392

10.2

AI

No

add date

No document provides all required documentation and certification details for the specific order, including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and resul...

Open

3393

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification listing and digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Di...

Open

3394

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51...

Open

3395

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

3396

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3397

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - ...

Open

3398

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790; manufacturing process and furnace qualification comply with NORSOK M-650/ISO 17782; MST-Tubes is M-650 accredited for DMV 25.7N; free circulation of heating/cooling me...

Open

3399

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3400

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and explicit reference to Table 3 for tensile tests, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed...

Open

3401

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% for DMV 25.7N, meeting the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3402

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations. The or...

Open

3403

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3404

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

3405

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible and fulfilled for the specified pipe dimensions, as the wall thickness exceeds the minimum required for testing. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destruc...

Open

3406

4.3

AI

No

add date

DMV 25.7N fulfills NORSOK MDS D51 Rev 6 impact test requirements: Charpy V-notch at -46°C, minimum absorbed energy (transverse: 45J/35J, longitudinal: 65J/50J), and sub-size reduction factors. The specified pipe dimensions allow for required transver...

Open

3407

4.4.1

AI

No

add date

Micrographic examination and ferrite check are performed as per ISO 17781, with etching by 20-40% NaOH or KOH for intermetallic phases and 10% oxalic acid or V2A followed by 20-40% NaOH or KOH for nitrides/carbides, matching the requirement for metal...

Open

3408

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

3409

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

3410

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs are included noting and recording the presence and location of intermetallic phases. So...

Open

3411

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

3412

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

3413

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fulfilled. Source: DMV_STANDAR...

Open

3414

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_ST...

Open

3415

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, including etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and co...

Open

3416

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORS...

Open

3417

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

3418

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

3419

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

3420

5.2

AI

No

add date

NDE per ASTM A790 is detailed, but compliance with additional NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 requirements is not confirmed. For OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic testing is only available a...

Open

3421

5.2

AI

No

add date

The specific NDE acceptance criterion that any indication greater than that produced by the calibration notch represents a defect, requiring rejection or repair, is not explicitly stated in the referenced documents. Additionally, standard NDE is not ...

Open

3422

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as specified, with no deviations or overrides from TechnipFMC indicated. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances accord...

Open

3423

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSO...

Open

3424

8.0

AI

No

add date

Marking per ASTM A790 and standard methods (indelible ink, vibro-etching) include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Certification per EN 10204 3.1 provides supporting details. Source: DMV_STAND...

Open

3425

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

3426

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

3427

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demons...

Open

3428

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, are provided and fulfill the requirement for documentation traceable to delivered products as ...

Open

3429

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications and plant documentation. Source: DMV_STANDARD_BOOK/02-04-03 - Dig...

Open

3430

10.2

AI

No

add date

No document provides all required documentation or certification details for the specific order, including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and com...

Open

3431

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification and all relevant chemical, mechanical, and testing requirements fulfilled for 25 Cr Duplex stainless steel seamless ...

Open

3432

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability or full qualification per requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

3433

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

3434

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3435

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - ...

Open

3436

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is covered by compliance...

Open

3437

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

3438

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and lot requirements for destructive testing, directly matching the outlined requirement for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

3439

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, longitudinal if not feasible), corrosion, and microstructure tests are performed at specified...

Open

3440

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, meeting Table 4 requirements (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%). Hardness testing is performed per ASTM A790, with results provided. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

3441

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required by NORSOK MDS D51 Rev 6 and ASTM A790 for seamless pipe specification. Source: DMV_STANDARD_BO...

Open

3442

4.3

AI

No

add date

Pipe OD and wall thickness exceed minimums for Charpy V-notch testing per ASTM and ISO standards; testing as specified is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Imp...

Open

3443

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse absorbed energy (average/single) of 45 J/35 J, minimum longitudinal absorbed energy (average/single) of 65 J/50 J (if tran...

Open

3444

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with etching by 20-40% NaOH or KOH after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Di...

Open

3445

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

3446

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

3447

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

3448

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

3449

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

3450

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fulfilled. Source: ...

Open

3451

4.4.3

AI

No

add date

Ferrite content is determined per ISO 17781 using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

3452

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

3453

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

3454

4.5

AI

No

add date

Applicable standards and referenced documents do not mention ASTM G48 or ISO 17781, and there is no explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/12-03-01- Corro...

Open

3455

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including chemical composition, ferrite content, PRE, tensile, impact, corrosion, microstructure, and is M-650 qualified for the specified wall thickness r...

Open

3456

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

3457

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor are their roles and responsibilities defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructiv...

Open

3458

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

3459

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with explicit coverage of mechanical, chemical, and testing requirements for duplex stainless steel pipes. ...

Open

3460

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/NORSOK M-650/ISO 17782 are not confirmed. Provided information only covers ASTM NDE methods, not NORSOK-specific requirements. For OD 219.1 mm, eddy current testing is not feasible at Mon...

Open

3461

5.2

AI

No

add date

None of the relevant documents explicitly confirm that any indication greater than that produced by the calibration notch is treated as a defect and that defective pipe and tubing are rejected or repaired as required. Source: DMV_STANDARD_BOOK/02-03-...

Open

3462

6.0

AI

No

add date

Dimensional tolerances for the requested pipe are per the applicable ASTM standard (ASTM A790 referencing ASTM A999), with no override specified in the context. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - T...

Open

3463

7.0

AI

No

add date

Both ASTM A790 and NORSOK MDS D51 Rev 6 specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3464

8.0

AI

No

add date

Marking is performed according to ASTM A790, requiring full traceability to melt and heat treatment lot, and includes mandatory marking of heat number and DMV lot number to ensure traceability as required by the specification. Source: DMV_STANDARD_BO...

Open

3465

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 (§13, §14) for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3466

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

3467

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

3468

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

3469

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 manufacturing summary or QTR number, are provided and fulfill the requirement for documentation traceable to the products and trans...

Open

3470

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

3471

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of metallurgical and non-destructive testing f...

Open

3472

4.4.2

AI

No

add date

No information is provided regarding the detection, location, or micrographic documentation of intermetallic phases at 400x or higher magnification. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Micrographic Ex...

Open

3473

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/0...

Open

3474

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N within specified wall thickness limits, and the manufacturing process is qualified per NORSOK M-650 (or ISO 17782), meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD...

Open

3475

3.1

AI

No

add date

AOD or equivalent refining is used 100% for DMV 25.7N, and chemical analysis complies with Table 2 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

3476

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the requested WT of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest ...

Open

3477

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed per ASTM A790, with manufacturing process and furnace qualified according to NORSOK M-650 or ISO 17782. Free circulation of heating/cooling media is ensured by complianc...

Open

3478

4.1

AI

No

add date

Tensile and hardness tests are confirmed, but impact, corrosion, and microstructure examinations per heat and heat treatment lot are not fully addressed or confirmed as required by ASTM A790. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.doc...

Open

3479

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

3480

4.1

AI

No

add date

Tensile test direction is confirmed per ASTM A790, but there is no information on CVN impact testing, corrosion, or microstructure sampling as required. Thickness location and full test sampling details are not addressed. Source: DMV_STANDARD_BOOK/02...

Open

3481

4.2

AI

No

add date

Tensile testing is performed at room temperature with criteria matching Table 4, in accordance with ASTM A370 via reference to ASTM A790 and NORSOK MDS D51. Hardness testing is also performed as required. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

3482

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required for DMV 25.7N are not provided or confirmed in the referenced documents. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04...

Open

3483

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the ordered pipe (NPS 8, 219.1mm OD, 18.26mm WT), as it exceeds the minimum wall thickness required for both standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-0...

Open

3484

4.3

AI

No

add date

Impact testing at -46°C with required absorbed energy values for both longitudinal and transverse specimens is feasible for pipe with 18.26mm wall thickness; requirement can be fulfilled. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finis...

Open

3485

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination per ISO 17781 or specified etchant solution for 25 Cr Duplex stainless steels. No relevant information for duplex grades or required etching procedures provided.

Open

3486

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchants as per ISO 17781 Appendix B for micrographic examination; no confirmation of compliance with the etching requirement for ferrite balance and intermetallic phases. Source: DM...

Open

3487

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic phases; isolated phases are permitted if not homogeneously distributed and each is ≤10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

3488

4.4.2

AI

No

add date

Micrographic examination at minimum 400x magnification is mentioned, but there is no explicit confirmation that a representative micrograph at or near mid-wall thickness is recorded when intermetallic phases are not detected, nor that the micrograph ...

Open

3489

4.4.2

AI

No

add date

No provided documents address the reporting of centerline intermetallic stringers or specify acceptance criteria based on CVN and corrosion test results in their presence. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I.doc, DMV_...

Open

3490

4.4.2

AI

No

add date

Referenced documents allow isolated intermetallic precipitates below 10µm and do not prohibit all intermetallic phases/precipitates if CVN testing cannot be completed, which is stricter in the client requirement. Zero-tolerance is not met. Source: DM...

Open

3491

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided; only grain size measurement is discussed. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Microgr...

Open

3492

4.4.3

AI

No

add date

No acceptance criteria for micrographic examination are specified or addressed for DMV 25.7N in the provided sources. Source: Digest ASTM A 790.docx, Digest NORSOK MDS S01 Rev 05 .docx, Grain Size Examination in DMV-I.doc

Open

3493

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3494

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

3495

4.5

AI

No

add date

No acceptance criteria for metallurgical properties are specified or listed in the provided documents. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

3496

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria: no pitting at 20X magnification and weight loss < 1.0 g/m², matching the client's requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

3497

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDA...

Open

3498

5.2

AI

No

add date

No confirmation of 100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10, nor reference notches as specified, is provided in the relevant documentation. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive t...

Open

3499

5.2

AI

No

add date

100% qualitative anti-mixing PMI check is performed on standard production at Montbard using appropriate instruments, fulfilling general acceptance criteria for PMI under NDE. Source: DMV_STANDARD_BOOK/12-06-06 - Positive Material Identification (PMI...

Open

3500

5.2

AI

No

add date

No provided documentation confirms that NDE acceptance criteria are based on calibration notch indications or that pipes with greater indications are rejected or repaired for the specified dimension at Montbard; feasibility and referenced standards d...

Open

3501

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed as per the applicable ASTM standards (including ASTM A790/A999) for both hot and cold finished products, with no deviations or exceptions stated for the specified product dimensions and no ...

Open

3502

7.0

AI

No

add date

Finished pipes are required to be pickled or bright annealed by ASTM A790 and white pickled or bright annealed by NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790, NORSOK...

Open

3503

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13 - Marking/13-02 - Standard marking feasibility/13-02-01 - Standard marking feasibility - Montbard plant/13...

Open

3504

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 specifies that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

3505

10.0

AI

No

add date

No evidence is provided of an ISO 9001 quality-assurance system certified by a competent EEA body with a specific assessment for materials at the Montbard plant. Certification and inspection documents do not address this requirement explicitly. Sourc...

Open

3506

10.1

AI

No

add date

No evidence of ISO 9001 certification by a competent EEA body is provided as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-03 - Certification Mon...

Open

3507

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demonst...

Open

3508

10.2

AI

No

add date

No evidence that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205 or that the process is in place for the Montbard plant or the specific order. No explicit statement of compliance with the traceability a...

Open

3509

10.2

AI

No

add date

Mill Inspection Certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control; ASTM A790 and NORSOK M-630 are referenced in the order, implying inclusion of required information. Source: 14-03 - Certification Montbard plant.do...

Open

3510

10.2

AI

No

add date

No provided document contains the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or test results for metallu...

Open

3511

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

3512

1.0

AI

No

add date

No evidence that the supplier is qualified according to both NORSOK M-650 and ISO 17782, nor confirmation of QTR/MPCR availability for review. MST-Tubes is only M-650 accredited, not ISO 17782 accredited. Source: DMV_STANDARD_BOOK/02-04-03 - Digest N...

Open

3513

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process follows M-650 (or ISO 17782) qualified procedures, fulfilling the requirement for manufacturer and process qualification and meeting N...

Open

3514

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3515

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PREN ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3516

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

3517

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

3518

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

3519

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, all performed as required. For ...

Open

3520

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

3521

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

3522

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, meeting the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impac...

Open

3523

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal (if transvers...

Open

3524

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed according to ISO 17781, with specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

3525

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

3526

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic phases; isolated phases are permitted if not homogeneously distributed and each is <10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.do...

Open

3527

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 is performed with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

3528

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos including actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

3529

4.4.2

AI

No

add date

Presence of centerline intermetallic stringers must be reported, and acceptance is based on CVN and corrosion test results as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

3530

5.2

AI

No

add date

100% qualitative anti-mixing PMI checks are performed as standard with appropriate instruments and reporting per EN 10204 3.x, fulfilling general NDE acceptance criteria for PMI. Source: DMV_STANDARD_BOOK/12-06-06 - Positive Material Identification (...

Open

3531

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates below 10μm, which does not meet the stricter client requirement of no interm...

Open

3532

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

3533

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Structure must be free from intermetallic precipitates except isolated ones <10µm; carbides/nitrides are...

Open

3534

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies within this range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NOR...

Open

3535

4.5

AI

No

add date

No explicit confirmation or evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

3536

4.5

AI

No

add date

DMV 25.7N meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6 and ASTM A790, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

3537

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

3538

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

3539

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

3540

5.2

AI

No

add date

NDE methods required by ASTM A790 and NORSOK M-630 MDS D51 are not fully addressed; eddy current testing is not feasible for the specified OD, hydrostatic and ultrasonic tests are only available at extra cost, and full-length dye penetrant testing is...

Open

3541

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are considered defects requiring rejection or repair; standard NDE is not available for OD 219.1 mm at Montbard, and acceptance criteria are not confirmed for the requiremen...

Open

3542

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no alternative tolerances specified by the customer or TechnipFMC. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Toler...

Open

3543

8.0

AI

No

add date

Marking is performed according to ASTM A790 (§14) and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Diges...

Open

3544

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' confirming the requirement is met. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev...

Open

3545

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, meeting the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

3546

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers as specified in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

3547

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

3548

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

3549

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and will include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 -...

Open

3550

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. Other required ...

Open

3551

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

3552

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

3553

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3554

3.1

AI

No

add date

Chemical composition for UNS S32760 conforms to Table 2 of ASTM A790, matching the specified limits; heat analysis and supplier certification are performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dig...

Open

3555

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

3556

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

3557

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and explicit reference to Table 3 for tensile tests, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed...

Open

3558

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations. The ordered pipe...

Open

3559

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

3560

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets the requirements: yield strength ≥ 550 MPa, tensile strength ≥ 750 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 ...

Open

3561

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Im...

Open

3562

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if transverse...

Open

3563

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, using the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

3564

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

3565

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

3566

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

3567

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

3568

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

3569

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3570

4.4.3

AI

No

add date

Ferrite content is determined per ISO 17781 using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

3571

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosio...

Open

3572

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

3573

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 will be performed or is referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

3574

4.5

AI

No

add date

DMV 25.7N meets all metallurgical property acceptance criteria (chemical composition, mechanical properties, impact, corrosion, microstructure, ferrite) per NORSOK MDS D51 Rev 6 and ASTM A790, with M-650 qualification up to the required wall thicknes...

Open

3575

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02...

Open

3576

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

3577

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed on the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

3578

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51/ASTM A790 are not fully addressed; only ASTM A790/ASTM A999 NDE is confirmed, and Montbard plant has limited or non-standard NDE feasibility for the required OD and length, with ultrasonic and hydrosta...

Open

3579

5.2

AI

No

add date

None of the relevant documents explicitly confirm that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, as specified in the requirement. NDE acceptance criteria based on calibrat...

Open

3580

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a A...

Open

3581

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3582

8.0

AI

No

add date

Marking per ASTM A790 §14 and standard Montbard plant methods (indelible ink, vibro-etching) include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK...

Open

3583

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

3584

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

3585

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

3586

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

3587

10.2

AI

No

add date

Certification per EN 10204 type 3.1 is provided, including heat treatment, steel manufacturer, melting/refining practice, NORSOK M-650/ISO17782 summary or QTR number, and traceability to delivered products as required by SIR205. Source: DMV_STANDARD_...

Open

3588

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

3589

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. Other required ...

Open

3590

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 Rev. 6, including relevant chemical, mechanical, and testing requirements. Manufacturing is qualified to NORSOK M-6...

Open

3591

1.0

AI

No

add date

No document confirms supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor the availability of the full Qualification Test Record/MPCR for review as required by the specification. Source: DMV_STANDARD_BOOK/02 -...

Open

3592

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 (or ISO 17782), fulfilling the requirement for manufacturer and process qualification and meeting NORSO...

Open

3593

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N meets the chemical composition requirements of Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

3594

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the requested product (WT = 18.26 mm). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

3595

3.2

AI

No

add date

Manufacturing process is qualified to NORSOK M-650, heat treatment is solution annealing followed by accelerated cooling (water quenching) per ASTM A790, and process ensures compliance with furnace and circulation requirements per NORSOK M-650/ISO 17...

Open

3596

4.1

AI

No

add date

No provided document confirms that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790. Required testing frequency and lot definition are n...

Open

3597

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

3598

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no evidence of CVN impact testing, required test directions, or specified thickness locations for all required tests. Hardness, CVN, and corrosion/microstructure test sampling details are not a...

Open

3599

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4. Hardness testing is also performed as required. Source: DMV_STANDARD_B...

Open

3600

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required for DMV 25.7N are not confirmed as met; referenced documents either do not specify these values or provide values for different grades that do not meet the r...

Open

3601

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfills the requirement as the pipe dimensions exceed the minimum wall thickness required for testing according to ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished prod...

Open

3602

4.3

AI

No

add date

Impact testing at -46°C with specified absorbed energy values is feasible and can be fulfilled for pipe with 18.26mm wall thickness; transverse specimens are possible for NPS 8 at this thickness. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for h...

Open

3603

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination per ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels. Grain size examination is not applicable to duplex grades and no relevant procedures ...

Open

3604

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchants as per ISO 17781 Appendix B for micrographic examination; requirement not addressed for ferrite balance and intermetallic phases. Source: DMV_STANDARD_BOOK/12 - Special Test...

Open

3605

4.4.2

AI

No

add date

The microstructure must be basically free from intermetallic precipitates, with isolated precipitates allowed if not homogeneously distributed and each below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

3606

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided or addressed in the relevant documents or comments. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03...

Open

3607

4.4.2

AI

No

add date

Micrographic examination at a minimum of 400x magnification with photos is specified, but it is not confirmed that a representative micrograph at or near mid-wall thickness is recorded and reported at actual magnification with a scale bar when interm...

Open

3608

4.4.2

AI

No

add date

No relevant documents address the detection, reporting, or acceptance criteria for centerline intermetallic stringers, nor their relation to CVN and corrosion test results in case of their presence. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Exa...

Open

3609

4.4.2

AI

No

add date

Referenced specifications allow isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not meet the stricter client requirement of zero tolerance for intermetallic phases and/or precipitates when CVN tes...

Open

3610

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided or addressed in the relevant documents. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Micrograph...

Open

3611

4.4.3

AI

No

add date

No provided document specifies acceptance criteria or results for micrographic examination or metallurgical properties for DMV 25.7N; section 4.4 Micrographic Examination is not addressed and relevant standards or procedures are not confirmed for thi...

Open

3612

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.d...

Open

3613

4.5

AI

No

add date

Specific acceptance criteria for metallurgical properties for DMV 25.7N to A790 NORSOK are not detailed in the provided documents; only general requirements are listed without explicit acceptance criteria relevant to the requirement. Source: DMV_STAN...

Open

3614

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 G48 Method A at 25°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

3615

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Sources only address NDE method feasibility and technical details, n...

Open

3616

5.2

AI

No

add date

No explicit confirmation of 100% ultrasonic testing per ASTM E213 or ISO 10893-10 after all processing, nor evidence of compliance with reference notch requirements or process sequence is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02...

Open

3617

5.2

AI

No

add date

No provided document confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor do they specify the required NDE acceptance criteria for the requested pipe dimension or reference the cali...

Open

3618

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for the requested product dimensions are confirmed as per the applicable ASTM standards (including ASTM A790/A999), with no deviations or special tolerances specified by TechnipFMC. Requirement is fulfil...

Open

3619

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS S01 Rev 05 for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 ....

Open

3620

10.0

AI

No

add date

No evidence of an appropriate quality-assurance system (such as ISO 9001 certification by a competent EEA body) is provided for the Montbard plant or any other plant. Relevant documents do not confirm certification or assessment for materials. Source...

Open

3621

10.1

AI

No

add date

No evidence that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification is provided. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14...

Open

3622

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV 25.7N up to the required wall thickness, and the EN 10204 3.1 certificate will include the NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirem...

Open

3623

10.2

AI

No

add date

No evidence that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC as specified in the requirement. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-02 - Inspection Montbar...

Open

3624

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control for mill inspection as required. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-...

Open

3625

10.2

AI

No

add date

None of the reviewed documents provide the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or test results fo...

Open

3626

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification digest and the listed customer specifications for the requested item. Manufacturing is M-650 qualified up to t...

Open

3627

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; full qualification to NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR is not confirmed. Source: DMV_STANDARD_BOOK/02...

Open

3628

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

3629

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3630

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3631

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits and PREN requirements specified in Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 6 standards. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06...

Open

3632

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

3633

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

3634

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, directly referencing the required table for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

3635

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled per NORSOK MDS D51/ASTM A790. Fo...

Open

3636

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

3637

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

3638

4.3

AI

No

add date

Charpy V-notch testing as per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests...

Open

3639

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible), with reduction factors for sub-size...

Open

3640

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

3641

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is explicitly required for micrographic examination and matches the client's requirement ex...

Open

3642

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

3643

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

3644

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

3645

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

3646

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

3647

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. No evidence of stricter compliance...

Open

3648

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

3649

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781 with specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requirement f...

Open

3650

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3651

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or confirmed. Relevant standards and methods are not mentioned or explicitly confirmed in the available documentation. Source: DMV_STANDA...

Open

3652

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content...

Open

3653

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A @ 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these requirements. Source: DMV_STANDARD_BO...

Open

3654

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

3655

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed after all processing, and acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02...

Open

3656

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD (219.1 mm), Eddy current testing is not feasible, and hydrostatic/ultraso...

Open

3657

5.2

AI

No

add date

No provided document explicitly states that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, nor confirms standard NDE feasibility for the requested size at Montbard. NDE acceptance...

Open

3658

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation.

Open

3659

6.0

AI

No

add date

Dimensional tolerances for the specified product are confirmed to be per the applicable ASTM standard, with no overriding specifications noted. Source: DMV_STANDARD_BOOK/07 - Dimensional Tolerances/07-01 - General information/07.01 - General informat...

Open

3660

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3661

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

3662

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated in NORSOK MDS D51 Rev 06, §14. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3663

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

3664

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

3665

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

3666

10.2

AI

No

add date

ISO 9001 certification is provided and documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, is traceable to the products and transmitted to TechnipFMC as required by SIR205. Source: DM...

Open

3667

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - ...

Open

3668

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution annealing parameters, and ...

Open

3669

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

3670

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N but not to ISO 17782, as explicitly required. No evidence of QTR/MPCR documentation availability is provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

3671

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N with wall thickness up to 31.75 mm (hot finished), and the manufacturing process is qualified per M-650/ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

3672

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3673

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits and PREN requirements specified in Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 6 standards. Heat analysis and supplier certification are performed per heat. Source: 02-03-01 ...

Open

3674

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

3675

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

3676

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

3677

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specifi...

Open

3678

4.2

AI

No

add date

Tensile testing is performed per ASTM A370/ISO 6892-1 at room temperature, and the material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

3679

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

3680

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370 and ISO 148-1 requirements. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

3681

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C, and the specified pipe dimensions allow for both transverse and longitudinal Charpy V-notch testing as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK M...

Open

3682

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

3683

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

3684

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

3685

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

3686

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

3687

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

3688

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

3689

4.4.3

AI

No

add date

Microstructure examination is performed as per ISO 17781 at ≥400X magnification, with acceptance criteria requiring the structure to be free from intermetallic precipitates (isolated precipitates <10µm allowed), and carbides/nitrides findings reporte...

Open

3690

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

3691

4.5

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 metallurgical acceptance criteria, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

3692

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

3693

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

3694

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

3695

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782-specific NDE requirements are not addressed. For the requested OD, eddy current and ultrasonic testing are only available at extra cost and require technical co...

Open

3696

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair; the specific acceptance criterion is not addressed or confirmed for the requested product and ...

Open

3697

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the specified pipe, with no overriding requirements from TechnipFMC indicated. Source: 07.01 - General information.doc, 07.03.01 - Tolerances according to ASTM A 312-01a...

Open

3698

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and standard practice at Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_S...

Open

3699

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

3700

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

3701

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

3702

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

3703

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

3704

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

3705

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer identification, steel melting practice and refining method, heat number, chemical analysis (ladle), solution annealing...

Open

3706

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

3707

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV 25.7N but not to ISO 17782, as required. No confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 ...

Open

3708

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

3709

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3710

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2, and DMV material conforms with supplier certification and heat analysis per ASTM A790 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - D...

Open

3711

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

3712

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

3713

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/...

Open

3714

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, in compliance with ASTM A790 a...

Open

3715

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

3716

4.4.2

AI

No

add date

No relevant documents address the reporting of centerline intermetallic stringers or acceptance based on CVN and corrosion test results in such cases.

Open

3717

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

3718

4.3

AI

No

add date

Pipe wall thickness exceeds the minimum required for Charpy V-notch testing per ASTM A370 and ISO 148-1; testing feasibility is confirmed for >6 mm WT. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests...

Open

3719

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C: minimum transverse (average 45 J, single 35 J) and longitudinal (average 65 J, single 50 J) values, with applicable sub-size reduction factors. The specified pipe di...

Open

3720

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

3721

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

3722

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

3723

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

3724

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

3725

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

3726

4.4.2

AI

No

add date

The available specifications allow isolated intermetallic precipitates below 10μm, while the requirement prohibits all intermetallic phases and/or precipitates if CVN testing cannot be completed. The stricter client requirement is not fully met by th...

Open

3727

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

3728

4.4.3

AI

No

add date

Microstructure examination per ISO 17781 is specified, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impac...

Open

3729

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

3730

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

3731

4.5

AI

No

add date

DMV 25.7N meets all metallurgical property requirements and acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

3732

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781 (G48 Method A @ 50°C, 24h). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Diges...

Open

3733

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source: DM...

Open

3734

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

3735

5.2

AI

No

add date

NDE per ASTM A790 is partially feasible, but NORSOK M-630 MDS D51/ISO 17782-specific NDE acceptance criteria are not confirmed. Eddy current testing is not feasible for the required OD, and ultrasonic/hydrostatic tests are only available at extra cos...

Open

3736

5.2

AI

No

add date

No provided document confirms the NDE acceptance criterion that any indication greater than the calibration notch is a defect requiring rejection or repair; standard NDE methods are not feasible or only available at extra cost for the specified OD at...

Open

3737

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790/A999) for the specified pipe size, with no deviations or overrides from TechnipFMC indicated in the specification or part report/drawing. Source: DMV_STANDARD_BOOK...

Open

3738

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3739

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790, requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, and certification per EN 10204 3.1 includes relevant traceabi...

Open

3740

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

3741

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

3742

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-...

Open

3743

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification dem...

Open

3744

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

3745

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

3746

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

3747

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the spec...

Open

3748

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with explicit coverage of mechanical, chemical, and testing requirements, and the applicable n...

Open

3749

1.0

AI

No

add date

Supplier is qualified according to NORSOK M-650/ISO 17782 for the manufacturing process, meeting the requirement for relevant qualification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NO...

Open

3750

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per M-650 with compliance to NORSOK M-630 MDS D51 Rev. 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

3751

3.1

AI

No

add date

AOD or equivalent is used for 100% of production, and DMV 25.7N complies with the required chemical analysis per Table 2. Source: 02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3752

3.1

AI

No

add date

DMV 25.7N (UNS S32760) is manufactured according to NORSOK M-650 qualified procedures, with accreditation for the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORS...

Open

3753

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed per ASTM A790, the manufacturing process and furnaces are qualified according to NORSOK M-650 (or ISO 17782), and compliance with these standards ensures free circulatio...

Open

3754

4.1

AI

No

add date

Tensile and hardness tests are performed, but there is no confirmation that impact, corrosion testing, and microstructure examinations are carried out for each heat and heat treatment lot as defined in ASTM A790. No evidence of full compliance with t...

Open

3755

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

3756

4.1

AI

No

add date

Test sampling details such as test direction, thickness location, and CVN requirements are not fully confirmed; tensile test direction and CVN impact test performance are not explicitly specified as required by the table. Source: DMV_STANDARD_BOOK/02...

Open

3757

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature with criteria matching or exceeding Table 4, and referenced standards require testing in accordance with ASTM A370 or ISO 6892-1. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

3758

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required are not confirmed in the provided documentation, and referenced grades do not meet the specified requirements for duplex/superduplex steels. Source: DMV_STAN...

Open

3759

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

3760

4.3

AI

No

add date

Pipe dimensions allow for both longitudinal and transverse Charpy V-notch impact specimens, meeting the specified temperature and energy requirements for impact testing in both directions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destru...

Open

3761

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N, with manufacturing processes qualified to NORSOK M-650 (or ISO 17782), and compliance with NORSOK M-630 MDS D51 rev. 6 is confirmed. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

3762

4.4.1

AI

No

add date

No evidence of metallographic preparation or examination per ISO 17781, nor use of the specified etchant for 25 Cr Duplex stainless steels. Grain size examination is only discussed for austenitic materials, not duplex steels. Source: DMV_STANDARD_BOO...

Open

3763

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant as per ISO 17781 Appendix B for micrographic examination to show ferrite balance and intermetallic phases is provided.

Open

3764

4.4.2

AI

No

add date

The micrographic examination section requires the microstructure to be basically free from intermetallic phases, allowing isolated phases if not homogeneously distributed and each is below 10 μm, matching the client's requirement exactly. Source: DMV...

Open

3765

4.4.2

AI

No

add date

No information is provided regarding the detection, recording, or micrographic documentation (at 400x or higher) of intermetallic phases; the requirement is not addressed or fulfilled by the available documents. Source: DMV_STANDARD_BOOK/12 - Special...

Open

3766

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

3767

4.4.2

AI

No

add date

NORSOK MDS D41 Rev 06 and NORSOK MDS D51 Rev 06 allow isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be co...

Open

3768

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided or addressed in the relevant documents or comments. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 ...

Open

3769

4.4.3

AI

No

add date

No acceptance criteria for micrographic examination are specified or addressed for DMV 25.7N in the provided sources; only procedures and general information are given without defined acceptance values or requirements for the order in question. Sourc...

Open

3770

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3771

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation or specifications. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

3772

4.5

AI

No

add date

No explicit acceptance criteria for metallurgical properties are specified in the referenced documents or section; only general requirements or headings are present, making validation impossible without further detail. Source: DMV_STANDARD_BOOK/02-03...

Open

3773

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

3774

5.1

AI

No

add date

No provided documents contain information about the qualification or certification of NDE personnel to ISO 9712 level II or III, or their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing ...

Open

3775

5.2

AI

No

add date

No evidence of 100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10, or use of reference notches as specified, is provided in the available documentation. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructiv...

Open

3776

5.2

AI

No

add date

Dye penetrant testing is performed on tube ends and bevels on request, matching standard practice, and 100% qualitative anti-mixing PMI checks are conducted on standard production at Montbard, fulfilling NDE acceptance criteria. Source: DMV_STANDARD_...

Open

3777

5.2

AI

No

add date

No provided document confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair; NDE feasibility and acceptance criteria are not explicitly addressed for the requirement. Source: DMV_STANDARD_...

Open

3778

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for both hot and cold finished products in the relevant size range are confirmed as per the applicable ASTM standards (including ASTM A 790 with A 999 for tolerances), with no overriding TechnipFMC speci...

Open

3779

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed per ASTM A790 and white pickled or bright annealed per NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790, NORSOK MDS S0...

Open

3780

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

3781

10.0

AI

No

add date

No evidence of an ISO 9001 or equivalent quality-assurance system certified by a competent EEA body is provided for the material manufacturer or Montbard plant. No certification details or compliance evidence are present in the referenced documents o...

Open

3782

10.1

AI

No

add date

No evidence that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body is provided. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-03 - Cer...

Open

3783

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV 25.7N up to the required wall thickness, and the EN 10204 3.1 certificate will include the NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirem...

Open

3784

10.2

AI

No

add date

No evidence that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC is provided in the relevant documents. Certification and inspection details are mentioned, but not the specific transmission or traceabi...

Open

3785

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 is issued and validated for mill inspection, which by standard practice includes information required by ASTM A790 and NORSOK M-630. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03...

Open

3786

10.2

AI

No

add date

No provided document contains the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or test results. Only ge...

Open

3787

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

3788

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N but not to ISO 17782; no confirmation of QTR/MPCR availability. Requirement for NORSOK M-650/ISO 17782 qualification and documentation availability is not fully met. Source: DMV_STANDA...

Open

3789

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3790

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat, confirming conformity to the requireme...

Open

3791

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N, and certification will state heat treatment per ASTM ...

Open

3792

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with lot defined per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

3793

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

3794

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests, with specified locations and directions, is fulfilled for DMV 25.7N per ...

Open

3795

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 at room temperature, meeting the required mechanical properties (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and maximum hardness per Table 4; DMV 25.7N complies. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

3796

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

3797

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

3798

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible), with reduction factors for sub-size s...

Open

3799

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

3800

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

3801

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

3802

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

3803

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

3804

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

3805

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STAN...

Open

3806

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 ...

Open

3807

4.4.3

AI

No

add date

Microstructure examination is performed as per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at minimum 400X magnification. Acceptance criteria: structure must be basically free from intermetallic precipitates (isolate...

Open

3808

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

3809

4.5

AI

No

add date

ASTM G48 Method 'A' corrosion testing at 50°C for 24h in accordance with ISO 17781 is not explicitly mentioned or confirmed; compliance cannot be validated based on the available information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Mon...

Open

3810

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO ...

Open

3811

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A @ 50°C, 24h) requires no pitting at 20X magnification and weight loss less than 1.0 g/m²; DMV 25.7N complies with both requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

3812

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor are their roles and responsibilities as defined in ISO 9712 addressed. Source: DMV_STANDARD_BOOK/12-02-01 - Non d...

Open

3813

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

3814

5.2

AI

No

add date

NDE per ASTM A790 is detailed, but compliance with additional NORSOK M-630 MDS D51 or M-650/ISO 17782 NDE requirements is not confirmed. For the specified OD, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available a...

Open

3815

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair; NDE feasibility for the specified dimension is also not confirmed as standard or available wit...

Open

3816

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding tolerances specified by the customer. Source: 07.01 - General information.doc, 07.03.01 - Tolerances according to ASTM A 312-01a A 376-02a A 790-02 (A 999-01).doc, 0...

Open

3817

7.0

AI

No

add date

ASTM A790 (6.1.3) and NORSOK MDS D51 (§13) both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3818

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

3819

8.0

AI

No

add date

Marking is performed according to ASTM A790, including heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13...

Open

3820

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

3821

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

3822

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system certified within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

3823

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

3824

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

3825

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

3826

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive te...

Open

3827

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

3828

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability or full compliance with both NORSOK M-650/ISO 17782 as required. Source: DMV_STANDARD_BOOK/02-04-03 - D...

Open

3829

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

3830

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3831

3.1

AI

No

add date

Chemical composition for S32760 matches Table 2 requirements and is confirmed to conform per heat analysis for the DMV material. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Dig...

Open

3832

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

3833

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

3834

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

3835

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

3836

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), corrosion, and microstructure, is performed per ASTM A790 and NORSOK MDS D51, with required directions and t...

Open

3837

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

3838

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW, fulfilling all Table 4 mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

3839

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

3840

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, including minimum absorbed energy values and sub-size reduction factors. The specified pipe dimensions allow for required transverse Charpy V-notch testing as per th...

Open

3841

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

3842

4.4.1

AI

No

add date

Etching with 20–40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

3843

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

3844

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

3845

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

3846

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

3847

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

3848

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

3849

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3850

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

3851

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is specified and fulfilled for DMV 25.7N according to NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

3852

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) performed in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

3853

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, microstructure, and ferrite requirements, with explicit compliance to ASTM A790 and NORSOK M-650/ISO 17782 standards. Source: DMV_ST...

Open

3854

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

3855

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

3856

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed on the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - U...

Open

3857

5.2

AI

No

add date

NDE (EC or UT) per ASTM A999/ASTM A790 is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For OD 219.1 mm at Montbard, eddy current testing is not feasible, hydros...

Open

3858

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair; NDE methods are not standard for the requested size and may not be feasible or only available at extra cost, so the req...

Open

3859

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are confirmed to be per the applicable ASTM standard (ASTM A999), with no deviations or special requirements from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc,...

Open

3860

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3861

8.0

AI

No

add date

Marking per ASTM A790 includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02...

Open

3862

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 explicitly states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NO...

Open

3863

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

3864

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

3865

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

3866

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

3867

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - ...

Open

3868

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice and refining method, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel produ...

Open

3869

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured and tested in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with all relevant mechanical, chemical, and testing requirements met for 25 Cr Duplex stainless steel seamless pipes. Source: DMV_...

Open

3870

1.0

AI

No

add date

Supplier is qualified according to NORSOK M-650/ISO 17782 as required for the product supplied. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D41 Rev 06....

Open

3871

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N within specified wall thickness limits, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_B...

Open

3872

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N meets the chemical composition requirements of Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

3873

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the requested product (WT = 18.26 mm). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

3874

3.2

AI

No

add date

Pipes are solution annealed and water quenched per ASTM A790, with furnaces and process qualified to NORSOK M-650, and free circulation of heating/cooling media ensured during heat treatment. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

3875

4.1

AI

No

add date

No evidence that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is carried out for each heat and heat treatment lot as defined in ASTM A790. Some tests are mentioned as feasible or standard, but not all requi...

Open

3876

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

3877

4.1

AI

No

add date

Tensile and hardness tests per ASTM A790 are confirmed, but there is no evidence of CVN impact testing, nor specification of required sampling locations or directions for all tests. No information on corrosion or microstructure tests is provided. Req...

Open

3878

4.2

AI

No

add date

Tensile testing is performed in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4. Hardness testing is also performed as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

3879

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required for DMV 25.7N are not confirmed as met; referenced documents either do not provide these values or refer to grades with lower properties than required. Sourc...

Open

3880

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the ordered pipe dimensions, meeting the minimum wall thickness requirements for both standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing...

Open

3881

4.3

AI

No

add date

Pipe dimensions allow for required transverse and longitudinal impact testing as per specification. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in Montbard plant/12-03-02 ...

Open

3882

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation, examination procedures, or compliance with ISO 17781 for 25 Cr Duplex stainless steels, nor about the specified etching procedures for intermetallic phases and ferrite balance. Source: ...

Open

3883

4.4.1

AI

No

add date

No information confirming the use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination is provided; compliance with this specific etching requirement is not demonstrated. Source: DMV_STA...

Open

3884

4.4.2

AI

No

add date

The microstructure must be basically free from intermetallic precipitates, but isolated precipitates are allowed if not distributed over the whole specimen and if the dimension of each precipitate is below 10 μm, matching the requirement exactly. Sou...

Open

3885

4.4.2

AI

No

add date

No information or micrographs regarding the presence and location of intermetallic phases at 400x magnification are provided; only grain size measurement is discussed, not intermetallic phases. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - D...

Open

3886

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

3887

4.4.2

AI

No

add date

No relevant documents address the reporting or acceptance criteria for centerline intermetallic stringers or their evaluation based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I.doc...

Open

3888

4.4.2

AI

No

add date

Referenced NORSOK documents allow isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not meet the stricter requirement of zero tolerance for intermetallic phases/precipitates when CVN testing cannot ...

Open

3889

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided; only grain size measurement is addressed, not the required ferrite determination methods or standards. Source: DMV_STANDARD_BOOK/12 - S...

Open

3890

4.4.3

AI

No

add date

No provided document specifies acceptance criteria or results for micrographic examination or metallurgical properties relevant to DMV 25.7N. Grain size examination is not applicable to duplex/super-duplex stainless steels and is not addressed for th...

Open

3891

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3892

4.5

AI

No

add date

No explicit acceptance criteria for metallurgical properties are specified or detailed for DMV 25.7N in the provided documentation. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - ...

Open

3893

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 G48 Method A at 25°C for 24 hours is required, with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the client's requirements. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

3894

5.1

AI

No

add date

No evidence provided regarding qualification or certification of NDE personnel to ISO 9712 level II or III, or their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montba...

Open

3895

5.2

AI

No

add date

No evidence provided that 100% ultrasonic testing for longitudinal defects is performed in accordance with ASTM E213 or ISO 10893-10, or that reference notches as per ASTM E213 Figure 3 are used after all processing steps. Dimensional feasibility onl...

Open

3896

5.2

AI

No

add date

100% qualitative anti-mixing PMI check is performed on standard production at Montbard using appropriate instruments, fulfilling general NDE acceptance criteria for PMI. Source: DMV_STANDARD_BOOK/12-06-06 - Positive Material Identification (PMI) in M...

Open

3897

5.2

AI

No

add date

ASTM A790 (via ASTM A999) requires that any indication greater than the calibration notch is considered a defect and such pipes must be rejected or repaired, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

3898

6.0

AI

No

add date

Dimensional tolerances for the requested product are confirmed to be per the applicable ASTM standards (including ASTM A790/A999) for OD and WT, with no overriding TechnipFMC specifications referenced. Source: DMV_STANDARD_BOOK/07 - Dimensional Toler...

Open

3899

7.0

AI

No

add date

Finished pipes are required to be pickled or bright annealed by ASTM A790 and white pickled or bright annealed by NORSOK MDS S01, directly fulfilling the requirement. Source: ASTM A790, NORSOK MDS S01.

Open

3900

9.0

AI

No

add date

Weld repairs are explicitly stated as not acceptable for MST-Tubes as a standard requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .d...

Open

3901

10.0

AI

No

add date

No evidence is provided that the material manufacturer has an ISO 9001 (or equivalent) certification by a competent EEA body or that a specific assessment for materials has been performed. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DM...

Open

3902

10.1

AI

No

add date

No evidence provided that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-03...

Open

3903

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV 25.7N up to the required wall thickness, and the EN 10204 3.1 certificate will include the NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirem...

Open

3904

10.2

AI

No

add date

No evidence that documentation traceable to the products and to be transmitted to TechnipFMC as required by SIR205 will be provided; traceability and transmission are not confirmed in the relevant documents. Source: DMV_STANDARD_BOOK/14-01 - General ...

Open

3905

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control for mill inspection, with implied compliance to ASTM A790 and NORSOK M-630 for the specified product and standards. Source: 14-03 - Certification Montbar...

Open

3906

10.2

AI

No

add date

No provided documentation includes the required NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of metallurgical and non-destructive testing for the ac...

Open

3907

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified up to the required wall thickness. Source: DMV...

Open

3908

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, with manufacturing process qualified per NORSOK M-650 (or ISO 17782), and compliance with NORSOK M-630 MDS D51 Rev. 6 is referenced. Source: DMV_STANDARD_BOOK/02 - S...

Open

3909

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3910

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN ≥ 40, as required by ASTM A790 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat to ensure compliance. Source: 02-03-01 -...

Open

3911

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

3912

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

3913

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for sampling, fulfilling the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

3914

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile and impact (CVN) tests are performed in transverse direction (longitudinal if not possible), hardness, corrosion, and microstructure tests are conduct...

Open

3915

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with tensile and hardness properties meeting Table 4 requirements for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spec...

Open

3916

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

3917

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Im...

Open

3918

4.3

AI

No

add date

DMV 25.7N fulfills NORSOK MDS D51 Rev 06 impact test requirements: Charpy V-notch at -46°C, minimum 45 J average and 35 J single in transverse, 65 J average and 50 J single in longitudinal (if transverse not possible), with sub-size reduction factors...

Open

3919

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

3920

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

3921

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

3922

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

3923

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

3924

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

3925

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates, which does not meet the stricter client requirement of not permitting any i...

Open

3926

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

3927

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

3928

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

3929

4.5

AI

No

add date

No explicit confirmation that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 will be performed or is fulfilled in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.d...

Open

3930

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content...

Open

3931

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A @ 50°C, 24h) requires no pitting at 20X magnification and weight loss < 1.0 g/m²; DMV 25.7N complies with both requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

3932

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712 requirements. Source: DMV_STANDARD_BOOK/12-02-01 -...

Open

3933

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within the machine's capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive...

Open

3934

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/NORSOK M-650/ISO 17782 are not fully addressed; only general NDE (hydrostatic/EC/UT) per ASTM A999 is confirmed, and Montbard plant has NDE feasibility limitations for the requested OD, w...

Open

3935

5.2

AI

No

add date

None of the reviewed documents explicitly confirm that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor do they specify this NDE acceptance criterion for the requested produc...

Open

3936

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790 referencing ASTM A999) for the specified pipe dimensions, with no deviations or special tolerances indicated by the customer specification or TechnipFMC part report/drawing. Sourc...

Open

3937

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

3938

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-0...

Open

3939

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

3940

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body established within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

3941

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

3942

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification dem...

Open

3943

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, are provided and meet the requirement for documentation traceable to delivered products as per...

Open

3944

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided as standard, including all information required by ASTM A790 and NORSOK M-630, and validated by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, D...

Open

3945

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all required metallurgi...

Open

3946

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured and tested in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, meeting all relevant mechanical, chemical, and testing requirements for 25 Cr Duplex stainless s...

Open

3947

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of QTR/MPCR documentation availability as required by the specification. MST-Tubes is only M-650 accredited for DMV25.7N, not IS...

Open

3948

3.0

AI

No

add date

MST-Tubes F is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, with manufacturing process qualified per NORSOK M-650 (or ISO 17782) and meeting NORSOK M-630 MDS D51 rev. 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

3949

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N complies with the required chemical analysis. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NOR...

Open

3950

3.1

AI

No

add date

DMV 25.7N (UNS S32760) is manufactured according to NORSOK M-650 qualification, and MST-Tubes F is M-650 accredited for UNS S32760/DMV25.7N up to WT = 31.75 mm, covering the requested WT of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

3951

3.2

AI

No

add date

Manufacturing process is qualified to NORSOK M-650, heat treatment is solution annealing followed by accelerated cooling (water quenching) per ASTM A790, and furnaces comply with NORSOK M-650/ISO 17782. Free circulation of heating and cooling media i...

Open

3952

4.1

AI

No

add date

No evidence that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is carried out for each heat and heat treatment lot as defined in ASTM A790; only partial or unrelated testing information is provided, with no ...

Open

3953

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required by the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

3954

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no evidence of CVN impact testing, required test directions, or specified sampling locations (outer surface, 1/2 thickness, full thickness) as required by Table 3. Microstructure and corrosion ...

Open

3955

4.2

AI

No

add date

Tensile testing is performed at room temperature with criteria matching Table 4 (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and frequency (1/lot) for DMV 25.7N, and hardness testing is performed with results in HRC. Compliance with ASTM A370 or ISO 6892...

Open

3956

4.2

AI

No

add date

None of the provided documents confirm that the mechanical property requirements for DMV 25.7N (tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, hardness max 310 HBW) are fulfilled. No relevant data for these properties is pres...

Open

3957

4.3

AI

No

add date

No evidence that Charpy V-notch testing is performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1, or that results meet Table 5 requirements. Feasibility of testing is confirmed, but actual performance and compliance are not documented. Sou...

Open

3958

4.3

AI

No

add date

Pipe dimensions allow for both longitudinal and transverse impact testing as required, fulfilling the impact property requirements at -46°C with specified absorbed energy values. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive test...

Open

3959

4.4.3

AI

No

add date

No information is provided regarding ferrite content measurement or compliance with ASTM E 562, ASTM E 1245, or ISO 17781. Requirement not addressed or fulfilled by the available documents.

Open

3960

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination according to ISO 17781 or specification of the required etchant solution for 25 Cr Duplex stainless steels is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testi...

Open

3961

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination of ferrite balance and intermetallic phases in the provided documentation. Source: DMV_STANDARD_BOOK/12 - Special ...

Open

3962

4.4.2

AI

No

add date

The micrographic examination section requires the microstructure to be basically free from intermetallic precipitates, allowing isolated precipitates if not homogeneously distributed and each is below 10 μm, matching the client's requirement exactly....

Open

3963

4.4.2

AI

No

add date

No information or documentation is provided regarding the detection, recording, or micrographic documentation (at 400x or higher) of intermetallic phases; the requirement is not addressed or fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/1...

Open

3964

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness if intermetallic pha...

Open

3965

4.4.2

AI

No

add date

No evidence of procedures for reporting centerline intermetallic stringers or acceptance criteria based on CVN and corrosion test results is provided in the relevant documents or comments. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination i...

Open

3966

4.4.2

AI

No

add date

Standards NORSOK MDS D41 Rev 06 and D51 Rev 06 allow isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not fully meet the requirement that intermetallic phases and/or precipitates are not permitted ...

Open

3967

4.4.3

AI

No

add date

No provided document specifies acceptance criteria or results for micrographic examination or metallurgical properties as required in section 4.4 of the client specification for DMV 25.7N at Montbard plant. No evidence of fulfillment for micrographic...

Open

3968

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, ...

Open

3969

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided in the available documentation or metadata. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

3970

4.5

AI

No

add date

No explicit acceptance criteria for metallurgical properties are specified in the provided documents, so fulfillment cannot be validated based on the available information. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOO...

Open

3971

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 G48 Method A at 25°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

3972

5.1

AI

No

add date

No evidence provided regarding qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDARD_BOOK...

Open

3973

5.2

AI

No

add date

No confirmation that 100% ultrasonic testing for longitudinal defects will be performed in accordance with ASTM E213 or ISO 10893-10, nor information on reference notches or timing after all processing steps is provided. Source: DMV_STANDARD_BOOK/12 ...

Open

3974

5.2

AI

No

add date

100% qualitative anti-mixing PMI checks are standard at Montbard, with quantitative PMI and procedures available if specified, fulfilling general NDE acceptance criteria for PMI. Source: DMV_STANDARD_BOOK/12-06-06 - Positive Material Identification (...

Open

3975

5.2

AI

No

add date

No provided document confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair; NDE acceptance criteria and related policies are not explicitly stated for the specified product and dimension....

Open

3976

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed as per the applicable ASTM standards (including ASTM A790/A999) for the specified dimensions, with no deviations or exceptions noted in the customer specification or referenced documents. S...

Open

3977

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed (ASTM A790) and white pickled or bright annealed (NORSOK MDS S01), directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790, NORSOK MDS S01.

Open

3978

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13 - Marking/13-02 - Standard marking feasibility/13-02-01 - Standard marking feasibility - Montbard plant/13-02-01 ...

Open

3979

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

3980

10.0

AI

No

add date

No evidence is provided that the material manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body with a specific assessment for materials. Certification details are not included in the available documents. Source: DMV...

Open

3981

10.1

AI

No

add date

No evidence that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body with specific assessment for materials, as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - C...

Open

3982

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV 25.7N up to the required wall thickness, and the EN 10204 3.1 certificate will include the NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, demonstrating qualifica...

Open

3983

10.2

AI

No

add date

No evidence that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC as specified in the requirement. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-02 - Inspection Montbar...

Open

3984

10.2

AI

No

add date

Material certificate is issued according to EN 10204 Type 3.1 and validated by Quality Control for mill inspection. Inclusion of ASTM A790 and NORSOK M-630 information is not explicitly confirmed but certificate type and process meet the requirement....

Open

3985

10.2

AI

No

add date

No provided document contains the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of metallurgi...

Open

3986

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

3987

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

3988

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

3989

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical analysis for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06...

Open

3990

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed by supplier certification and heat analysis per ASTM A790 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dige...

Open

3991

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

3992

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

3993

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

3994

4.1

AI

No

add date

All required destructive tests (tensile, hardness, CVN, corrosion, microstructure) for seamless pipes are performed per NORSOK MDS D51/ASTM A790, with correct test directions and locations. For the ordered pipe dimensions, transverse CVN specimens ar...

Open

3995

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

3996

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets the requirements: yield strength ≥ 550 MPa, tensile strength ≥ 750 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 ...

Open

3997

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, meeting the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 -...

Open

3998

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact test requirements: Charpy V-notch at -46°C, minimum average 45 J and single 35 J (transverse), 65/50 J (longitudinal if transverse not possible), including sub-size reduction factors. The specified...

Open

3999

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

4000

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

4001

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

4002

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

4003

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included at actual magnification and a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

4004

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

4005

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STAN...

Open

4006

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

4007

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

4008

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

4009

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4010

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 are fully met for DMV 25.7N, including compliance with all destructive and micrographic tests, specified criteria, and M-650 qualification up to the required wall thickness. So...

Open

4011

4.5

AI

No

add date

Requirement for no pitting at 20X magnification and weight loss less than 1.0 g/m² is met per ISO 17781 (G48 Method A @ 50°C, 24h) for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dige...

Open

4012

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

4013

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

4014

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630/MDS D51 are not confirmed as fulfilled; eddy current testing is not feasible for the required OD, hydrostatic and ultrasonic tests are only available at extra cost, and there is no confirmation t...

Open

4015

5.2

AI

No

add date

None of the referenced documents confirm that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor do they confirm feasibility of the required NDE for the specified dimensions at...

Open

4016

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STAN...

Open

4017

6.0

AI

No

add date

Dimensional tolerances are specified as per the applicable ASTM standard (ASTM A790 referencing ASTM A999), with no override from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances...

Open

4018

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4019

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods include heat number and DMV lot number, ensuring compliance with the requirement for traceability to melt and h...

Open

4020

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

4021

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

4022

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

4023

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification de...

Open

4024

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

4025

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification ...

Open

4026

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, ladle chemical analysis, solution annealing temperatur...

Open

4027

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the item table and confirmed by the digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-0...

Open

4028

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not to ISO 17782, as explicitly required. No confirmation of QTR/MPCR availability is provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4029

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

4030

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4031

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and DMV material composition conforms with supplier certification and heat analysis per ASTM A790 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - ...

Open

4032

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4033

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

4034

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

4035

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-0...

Open

4036

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per NORSOK MDS D51/ASTM A7...

Open

4037

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

4038

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

4039

4.3

AI

No

add date

Charpy V-notch testing as per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests...

Open

4040

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal. The requested pipe dimensions allow...

Open

4041

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

4042

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

4043

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

4044

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

4045

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

4046

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria based on CVN and corrosion...

Open

4047

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

4048

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impa...

Open

4049

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

4050

4.5

AI

No

add date

No explicit reference to corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 or related test results is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4051

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified per NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

4052

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

4053

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

4054

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is confirmed for the specified pipe dimensions; calibration procedures are expected to follow ASTM E213, including reference notches. Source: DMV_STANDARD_BOOK/12 - Speci...

Open

4055

5.2

AI

No

add date

NDE per ASTM A790 is available, but compliance with additional NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 NDE requirements is not confirmed. For the specified OD, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only av...

Open

4056

5.2

AI

No

add date

None of the referenced documents explicitly confirm that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair; NDE acceptance criteria and standard application for the specified dimen...

Open

4057

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no deviations or overrides specified by TechnipFMC for the relevant size and product type. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDA...

Open

4058

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4059

8.0

AI

No

add date

Marking per ASTM A790 and plant marking methods ensure mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSO...

Open

4060

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable' under 'Surface finish / Repairs of defects.' Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

4061

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

4062

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

4063

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, and QTR number is included as per M-650 qualification, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MCPR...

Open

4064

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

4065

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference. Source: DMV_STANDARD_BO...

Open

4066

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all metallurgical and no...

Open

4067

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification digest and customer specification listing. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_ST...

Open

4068

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability for review or full compliance with both standards as specified. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev ...

Open

4069

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

4070

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4071

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN ≥ 40, as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4072

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

4073

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

4074

4.1

AI

No

add date

Test specimen sampling is performed according to Table 3, with specified frequency for tensile tests, fulfilling the requirement for test specimen sampling as outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 ...

Open

4075

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness l...

Open

4076

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

4077

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 and ASTM A790 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

4078

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

4079

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energy values for both transverse and longitudinal directions, and the specified pipe dimensions allow for required testing directions and spec...

Open

4080

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

4081

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B requirements for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

4082

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

4083

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

4084

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

4085

4.4.2

AI

No

add date

Findings of intermetallic stringers must be reported, and acceptance is based on CVN and corrosion test results as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

4086

4.4.2

AI

No

add date

The referenced specifications allow isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. The stricter requirement is not fulfilled by the avai...

Open

4087

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

4088

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

4089

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

4090

4.5

AI

No

add date

DMV 25.7N meets all metallurgical property requirements and acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

4091

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per NORSOK MDS D51 Rev 06 (ISO 17781, G48 Method A). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

4092

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source: DM...

Open

4093

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

4094

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/ISO 17782 are not confirmed as fulfilled; only ASTM A790/A999 NDE is referenced, and Montbard plant has NDE feasibility limitations for the requested OD. No evidence of compliance with NO...

Open

4095

5.2

AI

No

add date

None of the provided documents explicitly confirm that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor do they confirm that the required NDE will be performed as standard fo...

Open

4096

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) as required, with no evidence of a deviation or override from TechnipFMC in the provided context. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOO...

Open

4097

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4098

8.0

AI

No

add date

Marking is performed according to ASTM A790, requiring full traceability to melt and heat treatment lot, with mandatory marking of heat number and DMV lot number ensuring compliance with the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NO...

Open

4099

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4100

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

4101

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers as specified in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

4102

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

4103

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205 and section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

4104

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification ...

Open

4105

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

4106

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive te...

Open

4107

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification up to the required wall thickness. 'A790 NORSOK' is explicitly listed under customer specifications for the requested ite...

Open

4108

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence provided for QTR/MPCR availability for review by TechnipFMC as specified in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

4109

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

4110

3.1

AI

No

add date

AOD or equivalent refining is used for 100% of production, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4111

3.1

AI

No

add date

DMV 25.7N (UNS S32760) chemical composition matches the requirements of Table 2 and complies with ASTM A790 and NORSOK MDS D51 Rev 06, including PREN ≥ 40 and all specified element limits. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest ...

Open

4112

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

4113

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, with test frequency 1/lot matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

4114

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

4115

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790/NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure tests are performed at the requir...

Open

4116

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

4117

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets the requirements: yield strength ≥ 550 MPa, tensile strength ≥ 750 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

4118

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

4119

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for required testing directions. Source: 02-04-03 - ...

Open

4120

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

4121

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

4122

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

4123

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

4124

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

4125

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. No source fully prohibits intermetallics/precipitates in t...

Open

4126

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

4127

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

4128

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

4129

4.5

AI

No

add date

No explicit evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or referenced in the provided documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4130

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, including chemical composition, mechanical properties, impact, corrosion, microstructure, ferrite content, an...

Open

4131

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

4132

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

4133

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available and applicable for the specified pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultrasonic testing...

Open

4134

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782; no evidence of full qualification or QTR/MPCR availability as required by the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

4135

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4136

5.2

AI

No

add date

NDE per ASTM A790 is feasible, but NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782-specific NDE acceptance criteria are not validated. For the requested OD (219.1 mm), eddy current testing is not feasible, and hydrostatic or ultrasonic testing is onl...

Open

4137

5.2

AI

No

add date

No provided document explicitly states that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, nor confirms that the required NDE will be performed as standard for the specified pipe ...

Open

4138

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790) unless otherwise specified, with no evidence of deviation in the customer specification. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV...

Open

4139

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4140

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring compliance with the requirement. Source: DM...

Open

4141

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

4142

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

4143

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

4144

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified ...

Open

4145

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

4146

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications and plant documentation. Source: DMV_STANDARD_BOOK/02-04-03 - Dig...

Open

4147

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. Other required ...

Open

4148

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all relevant mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified for the required wall thickness. Source...

Open

4149

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - ...

Open

4150

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical analysis conforms to the specified table for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4151

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition requirements, including PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat to ensure conformity with the requir...

Open

4152

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - S...

Open

4153

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is carried out per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

4154

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

4155

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions, in accordance with ASTM A...

Open

4156

4.2

AI

No

add date

Tensile testing is performed in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 as required for DMV 25.7N seamless pipe per NORSOK MDS D51 and ASTM A790. Source: DMV_STANDARD_BOOK...

Open

4157

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: minimum tensile strength 750 MPa, yield strength 550 MPa, elongation 25%, and maximum hardness 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

4158

4.3

AI

No

add date

Pipe dimensions exceed minimum wall thickness required for Charpy V-notch testing as per ASTM A370, ASTM A1058, or ISO 148-1; testing is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing...

Open

4159

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements: Charpy V-notch testing at -466C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possibl...

Open

4160

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

4161

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is explicitly required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_...

Open

4162

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

4163

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

4164

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

4165

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

4166

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

4167

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

4168

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance is based on im...

Open

4169

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4170

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4171

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including chemical composition (PRE ≥ 40), mechanical properties, microstructure, ferrite content (35-60%), corrosion resistance (G48), and M-650 qualification for the re...

Open

4172

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

4173

5.1

AI

No

add date

No evidence provided regarding qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source: DMV_STAND...

Open

4174

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, which are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-0...

Open

4175

5.2

AI

No

add date

NDE per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 is required, but only ASTM A790/A999 NDE is detailed, and there is no explicit confirmation of NORSOK compliance. For the specified OD (219.1 mm), eddy current testing is not feasible, and hydro...

Open

4176

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair; NDE feasibility for the specified dimension is also not confirmed for standard processing at M...

Open

4177

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) unless otherwise specified, with no overriding requirements indicated by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - ...

Open

4178

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4179

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures ensures mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

4180

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

4181

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

4182

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling supplier qualification documentation requirem...

Open

4183

10.2

AI

No

add date

No explicit confirmation that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205 is provided in the relevant sources. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03...

Open

4184

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard, including all information required by ASTM A790 and NORSOK M-630, and are validated by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

4185

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, ladle chemical analysis, solution annealing temperatur...

Open

4186

1.0

AI

No

add date

DMV 25.7N seamless pipes are confirmed as fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

4187

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N but not to ISO 17782; no evidence of full qualification or availability of QTR/MPCR as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

4188

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

4189

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4190

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PREN ≥ 40, and meets ASTM A790 and NORSOK MDS D51 Rev 06 standards for chemical limits. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORS...

Open

4191

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

4192

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4193

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for one set per heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

4194

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-0...

Open

4195

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specified locations. Fo...

Open

4196

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the specified tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

4197

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

4198

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

4199

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal, and the specified pipe dimensions allow for required transverse t...

Open

4200

4.4.1

AI

No

add date

Micrographic examination and ferrite check are performed as per ISO 17781, but the specific etchant solution required by the client is not confirmed; only general etching solutions are mentioned, not the exact one specified in the requirement. Source...

Open

4201

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

4202

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

4203

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

4204

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

4205

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

4206

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

4207

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

4208

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosio...

Open

4209

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4210

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, chemical composition, ferrite content, and corrosion/impact requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

4211

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N, with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/0...

Open

4212

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

4213

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 can be performed after all processing steps, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non ...

Open

4214

5.2

AI

No

add date

NDE per ASTM A790 is partially addressed (hydrostatic or EC/UT per ASTM A999), but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE acceptance criteria are met. For OD 219.1 mm, eddy current testing is not f...

Open

4215

5.2

AI

No

add date

The available documents do not confirm that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor do they confirm that the required NDE will be performed as standard for the speci...

Open

4216

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no override specified in the customer requirements or context. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General informat...

Open

4217

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4218

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 §16, both requiring full traceability to heat (melt) and heat treatment lot. Marking methods include mandatory heat and DMV lot numbers, ensuring compliance with the requirement. Source: D...

Open

4219

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4220

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

4221

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

4222

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW, fulfilling all Table 4 mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

4223

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, fulfilling the requirement for qualification for the specified size and produ...

Open

4224

10.2

AI

No

add date

No provided document explicitly confirms that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205. Certification and quality assurance are mentioned, but not the specific transmission and traceability requi...

Open

4225

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided as standard and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the specification section as the basis for documentation. Source: DMV_STANDARD_B...

Open

4226

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or complete metallurgical and non-dest...

Open

4227

1.0

AI

No

add date

DMV 25.7N seamless pipe is specified as compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, fulfilling all mechanical, chemical, corrosion, and qualification requirements, including manufacturing, testing, and certification. Source: DMV_STANDAR...

Open

4228

1.0

AI

No

add date

Supplier is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N but not accredited to ISO 17782 as required; no evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4229

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

4230

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4231

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

4232

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

4233

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

4234

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-0...

Open

4235

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per NORSOK MDS D51/ASTM A7...

Open

4236

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 as referenced in ASTM A790, and material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

4237

4.3

AI

No

add date

Charpy V-notch testing as per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 -...

Open

4238

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, with minimum absorbed energy values for transverse and longitudinal specimens, and the specified pipe dimensions allow for standard transverse Charpy V-notch testin...

Open

4239

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with specified etchants after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

4240

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

4241

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

4242

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

4243

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

4244

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

4245

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is...

Open

4246

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

4247

4.4.3

AI

No

add date

Micrographic examination per ISO 17781 is specified, including etching for intermetallic phases, nitrides, and carbides, minimum 400X magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm,...

Open

4248

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

4249

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, fulfilling the requirement for manufacturer and process qualification and compliance with ...

Open

4250

4.1

AI

No

add date

All required tests (tensile, hardness, CVN, corrosion, microstructure) for seamless pipes are performed per NORSOK MDS D51/ASTM A790, with correct test directions and thickness locations. For the specified pipe dimensions, transverse CVN specimens ar...

Open

4251

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4252

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4253

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, with accredited manufacturing and qualification processes. Source: DMV_STANDARD_BOOK/02 - ...

Open

4254

4.5

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 requirements for pitting corrosion: no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781, G48 Method A at 50°C for 24 hours. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

4255

5.1

AI

No

add date

No evidence provided regarding qualification or certification of NDE personnel to ISO 9712 level II or III, or their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source: DMV_STANDARD_BOO...

Open

4256

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

4257

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For OD 219.1 mm, eddy current testing is feasible for the requested length, but hydro...

Open

4258

5.2

AI

No

add date

None of the relevant documents confirm that any indication greater than that produced by the calibration notch is considered a defect or that defective pipe and tubing shall be rejected or repaired according to this criterion. NDE acceptance criteria...

Open

4259

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790 referencing ASTM A999) for the specified product, with no deviations stated in the client specification or drawing. Source: DMV_STANDARD_BOOK/07-01 - General infor...

Open

4260

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4261

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number, lot number, and other traceable information, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

4262

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

4263

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system for materials within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

4264

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

4265

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

4266

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence provided for QTR/MPCR availability for review by TechnipFMC as specified in the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

4267

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

4268

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 ...

Open

4269

10.2

AI

No

add date

Most documentation and certification requirements are stated as included in the EN 10204 type 3.1 certificate, except the specific steel producer of the starting material, which is not provided (only country of origin is given). Actual solution annea...

Open

4270

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03...

Open

4271

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; full qualification to NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR is not confirmed. Source: DMV_STANDARD_BOOK/02-...

Open

4272

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

4273

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4274

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN ≥ 40 as required by NORSOK MDS D51 Rev 06 for ASTM A790 seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

4275

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

4276

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

4277

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling as outlined in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

4278

4.1

AI

No

add date

Test sampling requirements for seamless pipes per NORSOK MDS D51/ASTM A790—including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations—are f...

Open

4279

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, meeting the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Hardness testing is also performed as required. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

4280

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spe...

Open

4281

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for 18.26mm wall thickness and 219.1mm OD pipe as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impac...

Open

4282

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C with minimum transverse values of 45 J (average) and 35 J (single), and longitudinal values of 65 J (average) and 50 J (single) if transverse ...

Open

4283

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants after final polishing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

4284

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, is required for micrographic examination as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

4285

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

4286

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded as required. Source...

Open

4287

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

4288

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

4289

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm if not distributed over the whole specimen, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry ...

Open

4290

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

4291

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requirement for DMV 25....

Open

4292

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

4293

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4294

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4295

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

4296

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement not addressed in the reviewed documents. Source: DMV_STA...

Open

4297

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

4298

5.2

AI

No

add date

NDE per ASTM A790 is partially addressed with hydrostatic or NDE (EC or UT) testing per ASTM A999, but there is no explicit evidence of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements. Eddy current testi...

Open

4299

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair; NDE acceptance criteria per the requirement are not demonstrated for the specified ...

Open

4300

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and referenced ASTM A999, with no deviations or special requirements specified by TechnipFMC. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - T...

Open

4301

7.0

AI

No

add date

ASTM A790 (6.1.3) and NORSOK MDS D51 (§13) both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4302

8.0

AI

No

add date

Marking is performed per ASTM A790 §14 and includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_...

Open

4303

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

4304

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

4305

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

4306

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

4307

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

4308

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the specification section. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06....

Open

4309

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. No evidence is ...

Open

4310

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification and referenced documentation. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4311

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

4312

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4313

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat, confirming conformity to the requireme...

Open

4314

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

4315

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot, with 'lot' defined as per ASTM A790, fulfilling the requirement for testing per heat and heat treatment lot as specified. Source: DMV_STAND...

Open

4316

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

4317

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations, all per ASTM A790 and NORSOK requirement...

Open

4318

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-0...

Open

4319

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: minimum tensile strength 750 MPa, yield strength 550 MPa, elongation 25%, and maximum hardness 310 HBW, as specified by the client. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

4320

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, meeting the requirement. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

4321

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements at -466C: minimum 45/35 J (transverse) and 65/50 J (longitudinal) for thickness >6mm. The specified pipe dimensions allow for required impact testing directions and specimen sizes. Sou...

Open

4322

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

4323

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH solution is specified for detecting ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

4324

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

4325

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

4326

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

4327

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

4328

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

4329

4.4.3

AI

No

add date

Ferrite content is determined per ASTM E562 or by image analysis according to ASTM E1245, performed in accordance with ISO 17781, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

4330

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781 with specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requirement f...

Open

4331

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

4332

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is fulfilled or documented for the requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4333

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements, with M-650 qualification up to the specified wall thickness. Source: DMV_STANDARD_BOOK/02...

Open

4334

4.5

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06, which requires no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781, G48 Method A at 50°C for 24 hours. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

4335

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

4336

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

4337

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not addressed. For the requested OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at extra cost. Full-length d...

Open

4338

5.2

AI

No

add date

None of the provided documents explicitly confirm that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, as specified by the requirement. General NDE practices and references to s...

Open

4339

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and ASTM A999 as required, with no alternative specifications from TechnipFMC indicated. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolera...

Open

4340

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be pickled or bright annealed, fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4341

8.0

AI

No

add date

Marking includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAND...

Open

4342

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4343

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

4344

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

4345

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified s...

Open

4346

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products being delivered as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

4347

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

4348

10.2

AI

No

add date

EN 10204 3.1 certificates include most required information (NORSOK M-650/ISO 17782 QTR number, steel melting practice, heat treatment, etc.), but only the country of origin of the steel supplier is provided, not the specific steel producer. No evide...

Open

4349

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification digest and the listed customer specifications for the requested item. Manufacturing is M-650 qualified up to t...

Open

4350

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability. Requirement for qualification to both NORSOK M-650 and ISO 17782 is not fully met and supporting d...

Open

4351

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

4352

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4353

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PREN ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4354

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

4355

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

4356

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

4357

4.1

AI

No

add date

Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not feasible), and corrosion/microstructure at specified thickness locations, are fulfilled. For the ordered p...

Open

4358

4.2

AI

No

add date

Tensile testing is performed at room temperature in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

4359

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: yield strength ≥ 550 MPa, tensile strength ≥ 750 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

4360

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for 18.26mm wall thickness and 219.1mm OD pipe as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impac...

Open

4361

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, with minimum absorbed energy values of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal, including sub-size reduction ...

Open

4362

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

4363

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

4364

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

4365

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

4366

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, actual magnification and scale bar reported, fulfilling the requirement for a representative micrograph at or near mid-wall thickness if intermetallic pha...

Open

4367

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

4368

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates, which does not meet the stricter client requirement of not permitting any i...

Open

4369

4.4.3

AI

No

add date

Ferrite content is checked as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis per ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

4370

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Structure must be basically free from intermetallic precipitates; isolated precipitates allowed if not dis...

Open

4371

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4372

4.5

AI

No

add date

Applicable standards are referenced but there is no explicit confirmation that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or included in the documentation provided. Source: DMV_STANDARD_BOOK/12-03-...

Open

4373

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO ...

Open

4374

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

4375

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

4376

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

4377

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD (219.1 mm), standard NDE (eddy current, hydrostatic, ultrasonic) is not a...

Open

4378

5.2

AI

No

add date

No provided document confirms the NDE acceptance criterion that any indication greater than the calibration notch is a defect requiring rejection or repair, nor evidence that the required NDE methods and criteria are applied for the specified pipe si...

Open

4379

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standards (including A999), with no deviations specified by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolera...

Open

4380

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4381

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot, and standard marking methods (indelible ink, vibro-etching) include heat and lot numbers as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

4382

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4383

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

4384

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

4385

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness for the specified size and product form. Source: DMV_STANDARD_BOO...

Open

4386

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products as required by SIR205 and NORSOK M-650/ISO17782. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

4387

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630; Mill Inspection Certificates according to EN 10204 Type 3.1 are issued and validated by Quality Control at the Montbard plant. Source: 02-...

Open

4388

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or actual metallurgical and non-destru...

Open

4389

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, including all relevant mechanical, chemical, and testing requirements for 25 Cr Duplex stainless steel seam...

Open

4390

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

4391

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 and meets NORSOK MDS D51 Rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

4392

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N meets the required chemical composition per Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

4393

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the inquiry's WT of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest ...

Open

4394

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed per ASTM A790, with manufacturing process and furnaces qualified according to NORSOK M-650 (or ISO 17782), ensuring compliance with all specified requirements including ...

Open

4395

4.1

AI

No

add date

No evidence that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790. Testing frequency, lot definition, and required test types are not co...

Open

4396

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

4397

4.1

AI

No

add date

Test sampling requirements for tensile, hardness, CVN, corrosion, and microstructure tests on prolongation of seamless pipes, including test direction and thickness location per Table 3, are not fully addressed; missing details on test direction and ...

Open

4398

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature with criteria matching or exceeding Table 4 (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%), and the referenced standards require testing in accordance with ASTM A370 or ISO 6892-1. Source: DMV_STANDA...

Open

4399

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required in Table 4 for DMV 25.7N are not explicitly confirmed in the provided documentation. No direct evidence of fulfillment for the specified requirements is avai...

Open

4400

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, meeting the minimum wall thickness requirements for both ASTM and ISO standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Dest...

Open

4401

4.3

AI

No

add date

The pipe dimensions allow for transverse Charpy specimens, and the impact property requirements at -46°C can be fulfilled for this product. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - ...

Open

4402

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination according to ISO 17781 or specification of the required etchant for 25 Cr Duplex stainless steels is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-...

Open

4403

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination of ferrite balance and intermetallic phases. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive te...

Open

4404

4.4.2

AI

No

add date

The micrographic examination section requires the microstructure to be basically free from intermetallic phases, allowing isolated phases if not homogeneously distributed and each is below 10 μm, matching the client's requirement exactly. Source: DMV...

Open

4405

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided or addressed in the relevant documentation or comments. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/1...

Open

4406

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

4407

4.4.2

AI

No

add date

No relevant documents address the detection, reporting, or acceptance criteria for centerline intermetallic stringers, nor do they reference CVN or corrosion test results in relation to such findings. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size E...

Open

4408

4.4.2

AI

No

add date

NORSOK MDS D41 Rev 06 and D51 Rev 06 allow isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, even if CVN testing cannot be completed, whereas the client requires no intermetallic phases or precipitates in such...

Open

4409

4.4.3

AI

No

add date

No information is provided regarding ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781; only grain size measurement is discussed or no relevant comments are present.

Open

4410

4.4.3

AI

No

add date

No acceptance criteria for micrographic examination are specified or referenced in the provided documents for DMV 25.7N; only procedures and standards for grain size measurement are described without required values or criteria for the order in quest...

Open

4411

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4412

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4413

4.5

AI

No

add date

No explicit acceptance criteria for metallurgical properties are specified or validated for DMV 25.7N in the provided documents; referenced standards and sections do not fulfill the requirement for acceptance criteria definition or evidence of compli...

Open

4414

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

4415

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDA...

Open

4416

5.2

AI

No

add date

No evidence that 100% ultrasonic testing for longitudinal defects is performed in accordance with ASTM E213 or ISO 10893-10, or that reference notches as per Figure 3 of ASTM E213 are used after all processing steps. Source: DMV_STANDARD_BOOK/12 - Sp...

Open

4417

5.2

AI

No

add date

Dye penetrant testing is performed as required on tube ends and bevels, and 100% qualitative anti-mixing PMI is conducted on standard production at Montbard, fulfilling NDE acceptance criteria. Source: DMV_STANDARD_BOOK/12-02-05 - Dye penetrant inspe...

Open

4418

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor do they specify the required acceptance criteria for NDE indications relative to the calib...

Open

4419

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for the specified product dimensions are confirmed as compliant with the applicable ASTM standards (including ASTM A 790 with A 999 for tolerances), with no overriding TechnipFMC specifications noted. So...

Open

4420

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and white pickled or bright annealed per NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790 diges...

Open

4421

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

4422

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

4423

10.0

AI

No

add date

No evidence of an ISO 9001 quality-assurance system or certification by a competent EEA body is provided for the Montbard plant or manufacturer. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-01 - General information.doc, DMV_STANDARD_B...

Open

4424

10.1

AI

No

add date

No evidence provided that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-03...

Open

4425

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documents. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4426

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV25.7N up to WT 31.75 mm, covering the inquiry WT of 18.26 mm, and the EN 10204 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number. Source: DM...

Open

4427

10.2

AI

No

add date

No evidence is provided that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC as specified in the requirement. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-02 - Inspec...

Open

4428

10.2

AI

No

add date

Material certificate is issued according to EN 10204 Type 3.1 and validated by Quality Control for mill inspection; explicit inclusion of ASTM A790 and NORSOK M-630 information is not confirmed but certificate type and process meet the requirement. S...

Open

4429

10.2

AI

No

add date

No provided documents contain the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or test results. Only gener...

Open

4430

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with explicit confirmation of grade, manufacturing process, and relevant testing and accreditation. Source:...

Open

4431

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of QTR/MPCR availability for review. Partial accreditation to NORSOK M-650 is limited by wall thickness and does not cover ISO 1...

Open

4432

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm for hot finished, 10.925 mm for cold finished), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 require...

Open

4433

3.1

AI

No

add date

AOD or equivalent is used 100% for MST-Tubes, and DMV 25.7N complies with the chemical composition requirements in Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - D...

Open

4434

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the inquiry's WT of 18.26 mm, fulfilling the requirement for manufacturing process qualification per NORSOK M-650 or ISO 17782. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

4435

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed per ASTM A790, with manufacturing process and furnaces qualified according to NORSOK M-650/ISO 17782, ensuring compliance with requirements including free circulation of...

Open

4436

4.1

AI

No

add date

No evidence that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is carried out for each heat and heat treatment lot as defined in ASTM A790. Some tests are mentioned as feasible or standard, but not all requi...

Open

4437

4.1

AI

No

add date

Test specimen sampling is specified in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

4438

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4439

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no evidence of CVN impact testing, microstructure, or corrosion testing as required by the specified test sampling details (test direction, thickness location, and prolongation samples). Source...

Open

4440

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

4441

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required in Table 4 are not confirmed or are significantly lower than required; relevant documents do not provide evidence of fulfillment for DMV 25.7N (UNS S32750/S3...

Open

4442

4.3

AI

No

add date

No evidence that Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is performed or that results meet Table 5 requirements for the specified product or order position. Feasibility rules are mentioned, but compliance is not confirmed or do...

Open

4443

4.3

AI

No

add date

Impact testing at -466C with specified absorbed energy values is feasible and can be fulfilled for the pipe with 18.26mm wall thickness, as both longitudinal and transverse specimens can be taken for this product. Source: DMV_STANDARD_BOOK/12-03-02 ...

Open

4444

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination according to ISO 17781 or specification of the required etchant solution for 25 Cr Duplex stainless steels is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testi...

Open

4445

4.4.1

AI

No

add date

No evidence of etching with 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for ferrite balance and intermetallic phases examination in duplex/super-duplex steels is provided. No mention of ISO 17781 or relevant e...

Open

4446

4.4.2

AI

No

add date

The microstructure must be basically free from intermetallic precipitates, with isolated precipitates allowed if not distributed throughout the specimen and each below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

4447

4.4.2

AI

No

add date

No information or procedures are provided for noting and recording the presence and location of intermetallic phases with 400x micrographs as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Micrographic...

Open

4448

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at 400x minimum magnification with actual magnification and scale bar when intermetallic phases are not detected. Partial mention of 400x photos, but ...

Open

4449

4.4.2

AI

No

add date

No relevant documents address the detection, reporting, or acceptance criteria for centerline intermetallic stringers, nor do they link acceptance to CVN and corrosion test results if such stringers are present. Source: DMV_STANDARD_BOOK/12-03-03 - G...

Open

4450

4.4.2

AI

No

add date

Referenced specifications allow isolated intermetallic precipitates below 10μm if not distributed over the whole specimen, which does not meet the stricter client requirement of zero tolerance for intermetallic phases/precipitates when CVN testing ca...

Open

4451

4.4.3

AI

No

add date

No evidence of ferrite content determination by ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided or addressed in the relevant documents. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Micrograp...

Open

4452

4.4.3

AI

No

add date

No provided documents specify acceptance criteria or results for micrographic examination or related metallurgical properties for DMV 25.7N as required in section 4.4 Micrographic Examination. Requirement not fulfilled by available information. Sourc...

Open

4453

4.5

AI

No

add date

No acceptance criteria for metallurgical properties are specified or detailed for DMV 25.7N or A790 NORSOK in the provided documents; the requirement is not fulfilled by the available information. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

4454

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria: no pitting at 20X magnification and weight loss < 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

4455

5.1

AI

No

add date

No provided documents contain information on the qualification or certification of NDE personnel to ISO 9712 level II or III, nor on their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-...

Open

4456

5.2

AI

No

add date

No confirmation that 100% ultrasonic testing for longitudinal defects will be performed in accordance with ASTM E213 or ISO 10893-10, or that reference notches as per Figure 3 of ASTM E213 will be used. Dimensional range for ultrasonic testing is spe...

Open

4457

5.2

AI

No

add date

Dye penetrant testing is performed on tube ends and bevels on request, and qualitative 100% anti-mixing PMI is standard for production at Montbard, meeting the NDE requirements as specified in the inquiry without additional customer requests for stri...

Open

4458

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair for the requested pipe size; NDE feasibility and acceptance criteria are not explicitly address...

Open

4459

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for the requested product are confirmed to be in accordance with the applicable ASTM standards (including ASTM A790/A999) for the relevant size range, with no deviations or exceptions noted and no Techni...

Open

4460

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and white pickled or bright annealed per NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790 diges...

Open

4461

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

4462

9.0

AI

No

add date

Weld repairs are explicitly stated as not acceptable for MST-Tubes in the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

4463

10.0

AI

No

add date

No evidence of an ISO 9001 quality-assurance system or certification by a competent EEA body is provided for the material manufacturer or Montbard plant. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

4464

10.1

AI

No

add date

No evidence provided that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body with specific assessment for materials as required by the specification. Source: 14-03 - Certification Montbard plant.doc

Open

4465

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification will reference the QTR number, demonstrating qualification for the size and product form. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

4466

4.3

AI

No

add date

Charpy V-notch testing as per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests...

Open

4467

10.2

AI

No

add date

No evidence is provided that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205, nor is there confirmation of an ISO 9001 quality-assurance system certified by a competent EEA body for the Montbard plant. ...

Open

4468

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control for mill inspection, as required. Inclusion of all ASTM A790 and NORSOK M-630 information is not explicitly confirmed but the certificate type and proces...

Open

4469

10.2

AI

No

add date

No provided documentation includes NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or results of required metallurgical and non-destructive testing as specified in s...

Open

4470

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4471

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS...

Open

4472

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N (UNS S32760) up to 31.75 mm WT, and the requirement is for 18.26 mm WT. Manufacturing process is qualified to NORSOK M-650/ISO 17782, with testing per NORSOK M-630 MDS D51 rev. 6. Source: DMV_STANDAR...

Open

4473

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition is confirmed as compliant with Table 2 for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4474

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790 as required, with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 7...

Open

4475

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

4476

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

4477

4.1

AI

No

add date

Test specimen sampling is performed according to Table 3 of ASTM A790, confirming the requirement is fulfilled. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.do...

Open

4478

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per ASTM A790 and NORSOK r...

Open

4479

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with required tensile and maximum hardness properties met for DMV 25.7N. Hardness testing is also performed as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

4480

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 06 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

4481

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements: Charpy V-notch testing at -46°C, minimum absorbed energy 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal if transverse not possible. The spec...

Open

4482

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

4483

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

4484

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

4485

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

4486

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

4487

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

4488

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

4489

4.4.3

AI

No

add date

Ferrite content is checked per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

4490

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and ...

Open

4491

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

4492

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4493

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, chemical composition, ferrite content, corrosion, impact, PRE, mechanical properties, and microstructure. Sou...

Open

4494

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

4495

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

4496

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

4497

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD, eddy current testing is not feasible, and hydrostatic/ultrasonic tests a...

Open

4498

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair; NDE acceptance criteria are not specified and feasibility for the required OD is no...

Open

4499

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a A ...

Open

4500

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4501

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

4502

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required for DMV 25.7N seamless pipe under NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

4503

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

4504

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

4505

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

4506

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

4507

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO177...

Open

4508

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all metallurgical and no...

Open

4509

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

4510

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all relevant chemical, mechanical, manufacturing, and testing requirements. M-650 qualification is confirmed for the required wall ...

Open

4511

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782; no evidence provided for full qualification or availability of QTR/MPCR as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4512

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

4513

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4514

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PREN ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4515

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

4516

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot, with 'lot' defined as per ASTM A790, fulfilling the requirement for testing per heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 -...

Open

4517

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

4518

4.1

AI

No

add date

DMV 25.7N seamless pipes are tested per NORSOK MDS D51/ASTM A790 requirements, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure at specified locations. For the ...

Open

4519

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

4520

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

4521

4.3

AI

No

add date

Charpy V-notch testing is feasible and can be performed as the pipe wall thickness exceeds the minimum required by ASTM A370 and ISO 148-1 for both longitudinal and transverse directions. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finis...

Open

4522

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal, and the specified pipe dimensions allow for required transverse ...

Open

4523

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified electrolytic etchant after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

4524

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

4525

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

4526

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

4527

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

4528

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

4529

4.4.2

AI

No

add date

No provided documentation prohibits all intermetallic phases and/or precipitates when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10μm, which does not meet the stricter client requirement. Source: DMV_STA...

Open

4530

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

4531

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

4532

4.4.3

AI

No

add date

Ferrite content specified as 35% to 60%, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4533

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or specified. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4534

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spe...

Open

4535

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 24h, 50°C) is performed with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m²; DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

4536

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

4537

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

4538

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. For the requested OD (219.1 mm), standard NDE methods (EC, UT, hydrostatic) are only available at extra cost or require technical consulta...

Open

4539

5.2

AI

No

add date

None of the relevant documents explicitly state that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, and NDE capability for Eddy current testing is not feasible for the requested O...

Open

4540

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the specified pipe, with no overriding requirements from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - T...

Open

4541

7.0

AI

No

add date

ASTM A790 (6.1.3) and NORSOK MDS D51 (§13) both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4542

8.0

AI

No

add date

Marking per ASTM A790 §14 and standard Montbard plant methods (indelible ink, vibro-etching) include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NO...

Open

4543

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

4544

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

4545

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

4546

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

4547

10.2

AI

No

add date

No provided document confirms that the required documentation traceable to the products will be transmitted to TechnipFMC as specified by SIR205. Certification and inspection documents are mentioned, but not the specific transmission and traceability...

Open

4548

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing M-650/ISO17782 qualification as applicable. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK ...

Open

4549

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and results of all metallurgical and non-destructive testing...

Open

4550

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification digest and customer specification listing 'A790 NORSOK'. M-650 qualification is also met for the required wall thickness. Sou...

Open

4551

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not to ISO 17782, as explicitly required. No evidence of QTR/MPCR availability is provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4552

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

4553

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4554

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits and PREN requirements specified in Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 06 standards for chemistry and equivalency. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03...

Open

4555

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N, and certification will state heat treatment per ASTM ...

Open

4556

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

4557

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the specified frequency, fulfilling the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detai...

Open

4558

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations, is performed as required by NORSOK ...

Open

4559

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

4560

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets the minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) requirements per NORSOK MDS D51 Rev 06 and ASTM A790 for UNS S32760. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

4561

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

4562

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -466C, with specified minimum absorbed energy values for both transverse and longitudinal directions, and the pipe dimensions allow for required testing orientation and specimen si...

Open

4563

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

4564

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

4565

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

4566

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

4567

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, actual magnification and scale bar reported, fulfilling the requirement for a representative micrograph at or near mid-wall thickness if intermetallic pha...

Open

4568

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

4569

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: ASTM A790, NORSOK MDS D51 Rev 06.

Open

4570

4.4.2

AI

No

add date

The referenced specifications allow isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. This stricter requirement is not confirmed as fulfill...

Open

4571

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

4572

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

4573

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

4574

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4575

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 (ASTM A790, NORSOK M-630, M-650/ISO 17782) are fully met, including compliance for destructive and microstructural tests, and M-650 qualification for DMV 25.7N up to the requir...

Open

4576

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m²; DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

4577

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

4578

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

4579

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed; only ASTM A790/A999 NDE is detailed. For the specified OD (219.1 mm), eddy current testing is not feasible at Montbard, and hydrostatic/ultrasonic tests ar...

Open

4580

5.2

AI

No

add date

None of the relevant documents explicitly confirm that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair of pipe/tubing, nor do they confirm that NDE will be performed as standard ...

Open

4581

6.0

AI

No

add date

Dimensional tolerances are confirmed as per the applicable ASTM standard (ASTM A999 referenced by ASTM A790) for the requested pipe dimensions, with no overriding requirements specified by TechnipFMC in the provided context. Source: DMV_STANDARD_BOOK...

Open

4582

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4583

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

4584

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

4585

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

4586

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. EN 10204 type 3.1 certificates are also provided as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

4587

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

4588

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

4589

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications as specified. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D5...

Open

4590

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, steel melting practice, refining method, heat treatment condition, heat number, chemical analysis, solution annealing, and test resu...

Open

4591

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 Rev. 6. All relevant mechanical, chemical, and testing requirements are addressed for DMV 25.7N (UNS S32760). Sourc...

Open

4592

1.0

AI

No

add date

No evidence of supplier qualification to NORSOK M-650/ISO 17782 for the exact product supplied or availability of QTR/MPCR documentation as required by the specification. ISO 17782 accreditation is explicitly missing where NORSOK M-650 accreditation ...

Open

4593

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and qualification testing meets NORSOK M-630 MDS D51 Rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

4594

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N meets the chemical composition requirements of Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

4595

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the inquiry's wall thickness of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

4596

3.2

AI

No

add date

Manufacturing process is qualified to NORSOK M-650, heat treatment is solution annealed followed by accelerated cooling (water quenching) per ASTM A790, and furnaces/procedures are M-650 qualified ensuring proper heat treatment and media circulation ...

Open

4597

4.1

AI

No

add date

No evidence that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790; only partial or unrelated testing is mentioned and not at the require...

Open

4598

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

4599

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no evidence of CVN impact testing, required test directions, or sampling locations as specified in Table 3. Requirements for CVN, microstructure, and corrosion tests are not addressed or fulfil...

Open

4600

4.2

AI

No

add date

Tensile testing is performed with criteria matching Table 4, and NORSOK MDS D51 references ASTM A790, which requires mechanical testing per ASTM A370, fulfilling the requirement for tensile testing per ASTM A370 or ISO 6892-1 and meeting the specifie...

Open

4601

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required for DMV 25.7N are not confirmed in the provided sources; referenced documents either do not specify the required values or pertain to different steel grades....

Open

4602

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness required by the standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testin...

Open

4603

4.3

AI

No

add date

Impact testing at -46°C with specified absorbed energy values is feasible and can be fulfilled for pipe with 18.26mm wall thickness, as both ASTM and ISO rules confirm transverse specimens are possible for this size. Source: DMV_STANDARD_BOOK/12 - Sp...

Open

4604

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination according to ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels is provided. No mention of ISO 17781 or required etchants for duplex grades is found in the relevan...

Open

4605

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchants as per ISO 17781 Appendix B for micrographic examination; only grain size measurement for austenitic materials is addressed, not ferrite balance or intermetallic phases in d...

Open

4606

4.4.2

AI

No

add date

The microstructure must be basically free from intermetallic precipitates, but isolated precipitates are allowed if not distributed over the whole specimen and if the dimension of each precipitate is below 10 μm, matching the client's requirement exa...

Open

4607

4.4.2

AI

No

add date

No information is provided regarding the presence, location, or micrographic documentation (400x minimum) of intermetallic phases; the available documents only address grain size measurement for austenitic materials and do not fulfill the requirement...

Open

4608

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at 400x minimum magnification with actual magnification and scale bar when intermetallic phases are not detected. Partial mention of 400x photos, but ...

Open

4609

4.4.2

AI

No

add date

No evidence of procedures for reporting centerline intermetallic stringers or acceptance criteria based on CVN and corrosion test results in the presence of such stringers is provided. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DM...

Open

4610

4.4.2

AI

No

add date

NORSOK MDS D41 Rev 06 and D51 Rev 06 allow isolated intermetallic precipitates below 10μm if not distributed over the whole specimen, which does not meet the stricter client requirement of zero tolerance for intermetallic phases/precipitates when CVN...

Open

4611

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided; only grain size measurement is addressed, not ferrite content determination by the specified methods or standards. Source: DMV_STANDARD...

Open

4612

4.4.3

AI

No

add date

No provided document specifies acceptance criteria or results for micrographic examination or metallurgical properties for DMV 25.7N; relevant documents either do not address micrographic examination or are not applicable to duplex/super-duplex stain...

Open

4613

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4614

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided; only A790 NORSOK is referenced, which does not cover this specific requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Mont...

Open

4615

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are provided in the requirement or referenced documents, making validation impossible based on the available information. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_ST...

Open

4616

4.5

AI

No

add date

Specification requires pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², matching the client's requirements exactly. Source: DMV_STANDARD_BOOK/02 - ...

Open

4617

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712 for the Montbard plant. Sources: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_B...

Open

4618

5.2

AI

No

add date

No explicit confirmation that 100% ultrasonic testing per ASTM E213 or ISO 10893-10 will be performed after all processing steps or that calibration notches per Figure 3 of ASTM E213 will be used as specified. Dimensional feasibility is provided, but...

Open

4619

5.2

AI

No

add date

Dye penetrant testing is performed on tube ends and bevels as allowed, and 100% qualitative anti-mixing PMI check is conducted on standard production, fulfilling the NDE requirements. Source: DMV_STANDARD_BOOK/12-02-05 - Dye penetrant inspection in M...

Open

4620

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor do they specify this NDE acceptance criterion for the requested product and dim...

Open

4621

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for the requested product are confirmed as per the applicable ASTM standards (including ASTM A790 with A999 for tolerances), with no deviations or additional requirements stated for the specified dimensi...

Open

4622

7.0

AI

No

add date

ASTM A790 and NORSOK MDS S01 require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: ASTM A790, NORSOK MDS S01.

Open

4623

9.0

AI

No

add date

Weld repairs are not acceptable as per NORSOK MDS S01 Rev 05 for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

4624

10.0

AI

No

add date

No information confirming the manufacturer's quality-assurance system or ISO 9001 certification by a competent EEA body is provided. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Certification Montbard plant.doc

Open

4625

10.1

AI

No

add date

No evidence provided that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body with a specific assessment for materials as required by the specification. Source: DMV_STANDARD_BOOK/14-03 - Certification Montbard ...

Open

4626

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, demonstrating qualification for the size and product form. Source: DMV_STANDA...

Open

4627

10.2

AI

No

add date

No provided document confirms that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC as specified. There is no explicit mention of SIR205, traceability, or transmission process to TechnipFMC in the relev...

Open

4628

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control for mill inspection as required. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-...

Open

4629

10.2

AI

No

add date

No provided documents contain the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or metallurgical and non...

Open

4630

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured and tested in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, including all relevant mechanical, chemical, and testing requirements. Source: DMV_STANDARD_BOOK...

Open

4631

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of QTR/MPCR availability for review as required by the specification. MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV25....

Open

4632

3.0

AI

No

add date

MST-Tubes F is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm), and qualification testing meets NORSOK M-630 MDS D51 Rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

4633

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes and DMV 25.7N complies with the required chemical analysis in Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

4634

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the required WT of 18.26 mm for the inquiry. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-...

Open

4635

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed per ASTM A790, manufacturing process and furnaces are qualified according to NORSOK M-650 (or ISO 17782), and free circulation of heating/cooling media is ensured by com...

Open

4636

4.1

AI

No

add date

There is no evidence that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790; only partial or unrelated testing is mentioned, and required...

Open

4637

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

4638

4.1

AI

No

add date

Tensile and hardness tests per ASTM A790 are confirmed, but there is no evidence of CVN (impact), corrosion, or microstructure tests on prolongation samples with specified directions and thickness locations as required. Test sampling details are not ...

Open

4639

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

4640

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required for DMV 25.7N are not confirmed or addressed for the specified grade in the provided sources; fulfillment cannot be validated for the requirement. Source: DM...

Open

4641

4.3

AI

No

add date

No evidence that Charpy V-notch testing is performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1, or that results meet Table 5 requirements for the specified product and order context. Source: 02-02-01 Digest summary of ASTM A.docx, 12-03-...

Open

4642

4.3

AI

No

add date

Pipe dimensions allow for both longitudinal and transverse Charpy V-notch specimens; impact property requirements at -466C for both directions are feasible and can be fulfilled. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished produ...

Open

4643

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation, examination, or etching procedures per ISO 17781 for 25 Cr Duplex stainless steels or the specified etchant solution for intermetallic phases and ferrite balance. Source: DMV_STANDARD_B...

Open

4644

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchants as per ISO 17781 Appendix B for micrographic examination of ferrite balance and intermetallic phases is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Dest...

Open

4645

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic phases; isolated phases are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

4646

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation of intermetallic phases at 400x or higher is provided or addressed in the relevant documents or comments. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12...

Open

4647

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at 400x minimum magnification with actual magnification and scale bar when intermetallic phases are not detected. Partial mention of 400x photos, but ...

Open

4648

4.4.2

AI

No

add date

No relevant documents address the presence, reporting, or acceptance criteria for centerline intermetallic stringers, nor do they mention CVN or corrosion test results as a basis for acceptance if such stringers are present. Source: DMV_STANDARD_BOOK...

Open

4649

4.4.2

AI

No

add date

Micrographic examination per NORSOK MDS D41 and D51 allows isolated intermetallic precipitates below 10μm if not distributed over the whole specimen, which does not meet the stricter client requirement of zero tolerance for intermetallic phases/preci...

Open

4650

4.4.3

AI

No

add date

No information is provided confirming ferrite content determination per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781, nor is there mention of these standards or the required test being performed or reported as specified. Source: DMV_STANDAR...

Open

4651

4.4.3

AI

No

add date

No acceptance criteria or requirements for micrographic examination are provided or applicable for DMV 25.7N (super-duplex stainless steel); grain size examination is not required for this material type and is not addressed in the referenced standard...

Open

4652

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly fulfilled for DMV 25.7N as stated in the specifications and digest documents for NORSOK MDS D41 and D51. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK...

Open

4653

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or certified. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4654

4.5

AI

No

add date

No explicit acceptance criteria for metallurgical properties are specified in the provided documents; only general requirements or section headings are present without detailed criteria for acceptance. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM...

Open

4655

4.5

AI

No

add date

Specification requires pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², matching the client's requirements exactly. Source: DMV_STANDARD_BOOK/02 - ...

Open

4656

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

4657

5.2

AI

No

add date

No evidence that 100% ultrasonic testing for longitudinal defects will be performed according to ASTM E213 or ISO 10893-10, or that reference notches as specified are used. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testin...

Open

4658

5.2

AI

No

add date

Dye penetrant testing is performed as per standard practice for tube ends and bevels, and 100% qualitative anti-mixing PMI is conducted on standard production at Montbard, fulfilling the NDE acceptance criteria in the absence of additional customer r...

Open

4659

5.2

AI

No

add date

No provided document confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor do they specify acceptance criteria or disposition policy for such indications in NDE for the requested produc...

Open

4660

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for hot and cold finished products are in accordance with the applicable ASTM standards (including ASTM A790/A999) for the requested dimensions, with no deviations or overrides indicated by TechnipFMC or...

Open

4661

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790, NORSOK MDS S01.

Open

4662

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/13 - Marking/13-02 - Standard marking feasibility/13-02-01 - Standard marking feasibility - Montbard pla...

Open

4663

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

4664

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50°C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4665

10.0

AI

No

add date

No evidence of an ISO 9001 quality-assurance system or certification by a competent EEA body is provided for the material manufacturer or Montbard plant. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

4666

10.1

AI

No

add date

No evidence provided that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-03...

Open

4667

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, confirming qualification for the size and product form. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

4668

10.2

AI

No

add date

No evidence that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC as specified in the requirement. Certification and inspection documents are referenced, but transmission and traceability to TechnipFMC ...

Open

4669

10.2

AI

No

add date

A Mill inspection certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control, with reference to ASTM A790 and NORSOK M-630 in the customer specification, fulfilling the requirement for certification and included information...

Open

4670

10.2

AI

No

add date

None of the provided documents contain the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or test results. O...

Open

4671

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, DMV_STANDARD_BOOK/02-04-03 - D...

Open

4672

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782, as explicitly required. No evidence of QTR/MPCR documentation availability is provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4673

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

4674

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4675

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PRE ≥ 40, as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4676

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compliance with th...

Open

4677

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is carried out per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

4678

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

4679

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified th...

Open

4680

4.2

AI

No

add date

Tensile testing is performed at room temperature per required standards, and material meets specified tensile and hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dige...

Open

4681

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

4682

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and meets the requirement. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

4683

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements (Charpy V-notch at -46°C: transverse 45J/35J, longitudinal 65J/50J, sub-size reduction factors). The specified pipe dimensions allow for required transverse and longitudinal te...

Open

4684

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

4685

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

4686

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

4687

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs are included and recorded as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

4688

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

4689

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

4690

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully met. Source: ...

Open

4691

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

4692

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosio...

Open

4693

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4694

4.5

AI

No

add date

DMV 25.7N meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content. Source: DMV...

Open

4695

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

4696

5.1

AI

No

add date

No evidence provided regarding qualification or certification of NDE personnel to ISO 9712 level II or III, nor definition of their roles and responsibilities as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

4697

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within the machine's capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive...

Open

4698

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not addressed; standard NDE methods (EC, UT, hydrostatic) for the specified OD are either not feasible or only available at extra cost at Montbard; feasibility for ...

Open

4699

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, and standard NDE is not available for the requested OD at Montbard, making the requ...

Open

4700

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding TechnipFMC specification indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A 376-0...

Open

4701

7.0

AI

No

add date

ASTM A790 (6.1.3) and NORSOK MDS D51 (§13) both require finished pipes to be pickled or bright annealed, fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4702

8.0

AI

No

add date

Marking per ASTM A790 and standard plant methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

4703

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4704

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

4705

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

4706

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling supplier qualification documentation requirem...

Open

4707

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to delivered products, fulfilling SIR205 documentation requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

4708

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - ...

Open

4709

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice, heat number, chemical analysis, solution annealing details, or results of required metallurgical and non-destructive testing...

Open

4710

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 Rev. 6, including relevant chemical, mechanical, and testing requirements. Manufacturing process is qualified to NO...

Open

4711

1.0

AI

No

add date

No evidence that the supplier is qualified to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of the availability of the full Qualification Test Record/MPCR for review as required by the specification. Partial accredi...

Open

4712

3.0

AI

No

add date

MST-Tubes F is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, with manufacturing process qualified per M-650 (or ISO 17782) and meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

4713

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N meets the chemical composition requirements per Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

4714

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the requested product (WT = 18.26 mm). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

4715

3.2

AI

No

add date

Pipes are solution annealed and water quenched per ASTM A790, with furnaces and heat treatment in compliance with NORSOK M-650/ISO 17782, and free circulation of heating and cooling media ensured during the process. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

4716

4.1

AI

No

add date

There is no evidence that impact, tensile, hardness, corrosion testing, and microstructure examinations are performed for each heat and heat treatment lot as defined in ASTM A790; required tests and lot definitions are not confirmed for DMV 25.7N or ...

Open

4717

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

4718

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no information on CVN impact testing, test directions, or sampling locations as required. No confirmation of hardness, corrosion, or microstructure test sampling details per Table 3 requirement...

Open

4719

4.2

AI

No

add date

Tensile testing is performed at room temperature per NORSOK MDS D51, referencing ASTM A370, with results meeting or exceeding Table 4 requirements (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%). Hardness testing is also performed as required. Source: DMV_S...

Open

4720

4.2

AI

No

add date

Mechanical property values for UNS S32760 (tensile strength, yield strength, elongation, hardness) are not provided or confirmed to meet the specified minimums. Properties listed for TP316/316L do not fulfill the requirement for DMV 25.7N (S32760/S32...

Open

4721

4.3

AI

No

add date

No evidence that Charpy V-notch testing is performed or that results meet the specified standards and Table 5 requirements; only feasibility for testing is addressed, not actual compliance or results. Source: DMV_STANDARD_BOOK/02-02-01 Digest summary...

Open

4722

4.3

AI

No

add date

Pipe dimensions allow for transverse Charpy V-notch specimens, so impact property requirements at -46°C are met for both transverse and longitudinal directions as specified. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/1...

Open

4723

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination of 25 Cr Duplex stainless steels per ISO 17781 or the specified etching procedures for intermetallic phases and ferrite balance in duplex grades. Source: DMV_STANDARD_BOO...

Open

4724

4.4.1

AI

No

add date

No information confirming the use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination or to reveal ferrite balance and intermetallic phases is provided. Source: DMV_STANDARD_BOOK/12 - S...

Open

4725

4.4.2

AI

No

add date

The microstructure must be basically free from intermetallic precipitates, with isolated precipitates allowed if not distributed throughout the specimen and each below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

4726

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided or addressed in the relevant documentation or comments.

Open

4727

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at 400x minimum magnification with a scale bar and actual magnification when intermetallic phases are not detected, as required by the specification. ...

Open

4728

4.4.2

AI

No

add date

No relevant documents address the detection, reporting, or acceptance criteria for centerline intermetallic stringers, nor their linkage to CVN and corrosion test results as required. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV...

Open

4729

4.4.2

AI

No

add date

NORSOK MDS D41 Rev 06 and D51 Rev 06 allow isolated intermetallic precipitates below 10µm, but the client requires no intermetallic phases or precipitates if CVN testing cannot be completed. The requirement is not fully met by the referenced document...

Open

4730

4.4.3

AI

No

add date

No evidence of ferrite content determination by ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided; only grain size measurement is addressed, not ferrite content methods or standards required by the specification. Source: DMV_STANDARD...

Open

4731

4.4.3

AI

No

add date

No acceptance criteria or requirements for micrographic examination are provided or applicable for the requested grade in the relevant documents; grain size examination is not applicable to duplex/super-duplex stainless steels. Source: DMV_STANDARD_B...

Open

4732

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4733

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4734

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are provided; only a heading is present without detailed requirements or values for validation. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Dig...

Open

4735

4.5

AI

No

add date

Specification requires pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², matching the client's requirements exactly. Source: DMV_STANDARD_BOOK/02 - ...

Open

4736

5.1

AI

No

add date

No evidence provided regarding qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDARD_BOOK...

Open

4737

5.2

AI

No

add date

No evidence is provided that 100% ultrasonic testing for longitudinal defects will be performed in accordance with ASTM E213 or ISO 10893-10, or that reference notches as per Figure 3 of ASTM E213 will be used after all processing steps as required. ...

Open

4738

5.2

AI

No

add date

Dye penetrant testing is performed on tube ends and bevels on request, and 100% qualitative anti-mixing PMI is conducted on standard production, meeting the general NDE requirements for the Montbard plant as per the client inquiry and standard practi...

Open

4739

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch represents a defect and that defective pipe and tubing shall be rejected or repaired; acceptance criteria and rejection/repair policy are not explic...

Open

4740

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for the specified product sizes are confirmed as per the applicable ASTM standards (including ASTM A 790 with A 999 for tolerances), with no deviations or special tolerances indicated in the specificatio...

Open

4741

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed (ASTM A790) and white pickled or bright annealed (NORSOK MDS S01), directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790, NORSOK MDS S01.

Open

4742

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

4743

9.0

AI

No

add date

Weld repairs are not acceptable as per NORSOK MDS S01 Rev 05 for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

4744

10.0

AI

No

add date

No evidence of an ISO 9001 quality-assurance system or certification by a competent EEA body is provided for the Montbard plant or manufacturer. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Certification Montba...

Open

4745

10.1

AI

No

add date

No confirmation that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification M...

Open

4746

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV25.7N up to WT = 31.75 mm (requested WT is 18.26 mm), and the EN 10204 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number. Source:...

Open

4747

10.2

AI

No

add date

No provided document confirms that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205, nor is there evidence of an ISO 9001 (or equivalent) quality-assurance system certified by a competent EEA body. Sourc...

Open

4748

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control for mill inspection as required. Source: 14-03 - Certification Montbard plant.doc

Open

4749

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

4750

10.2

AI

No

add date

No documentation or data is provided for NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or metallurgical and non-destructive test results for the specific material ...

Open

4751

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all relevant mechanical, chemical, and testing requirements, and are M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02...

Open

4752

1.0

AI

No

add date

No evidence that the supplier is qualified to both NORSOK M-650 and ISO 17782 or that Qualification Test Records (QTR/MPCR) are available for review. Supplier is only accredited to M-650, not ISO 17782, and required documentation is not confirmed ava...

Open

4753

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

4754

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition complies with Table 2 requirements for DMV 25.7N seamless pipe. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4755

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements. Heat analysis is performed per heat, fulfilling the chemistry requirement for the applicable UNS. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

4756

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

4757

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

4758

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-0...

Open

4759

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specified locat...

Open

4760

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, meeting the tensile and maximum hardness properties of Table 4. Hardness testing is also performed and results are provided. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

4761

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

4762

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness (>6mm), fulfilling the requirement. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

4763

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4764

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum absorbed energies of 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal, and sub-size specime...

Open

4765

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

4766

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

4767

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

4768

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

4769

4.4.2

AI

No

add date

Micrographs at a minimum magnification of 400x are included, with actual magnification and scale bar, fulfilling the requirement for representative micrographs at or near mid-wall thickness if no intermetallic phases are detected. Source: DMV_STANDAR...

Open

4770

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK/0...

Open

4771

4.4.2

AI

No

add date

The referenced documents do not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed; isolated precipitates below 10µm are allowed, which does not meet the stricter client requirement of no intermetallics or prec...

Open

4772

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

4773

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impa...

Open

4774

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

4775

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or reported. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4776

4.5

AI

No

add date

DMV 25.7N meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, chemical composition, ferrite content, corrosion resistance, and M-650 qualification for the specified grade and wa...

Open

4777

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

4778

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to level II or III in accordance with ISO 9712 or equivalent, nor on the definition of their roles and responsibilities as per ISO 9712. Source: DMV_STANDARD_BOOK/1...

Open

4779

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed on the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

4780

5.2

AI

No

add date

NDE by hydrostatic, eddy current, or ultrasonic testing per ASTM A999/ASTM A790 is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD (219.1 mm),...

Open

4781

5.2

AI

No

add date

None of the referenced documents explicitly confirm that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair; NDE acceptance criteria and process capability for the specified dimensi...

Open

4782

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a A...

Open

4783

7.0

AI

No

add date

ASTM A790 (6.1.3) and NORSOK MDS D51 (§13) both require finished pipes to be pickled or bright annealed, fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4784

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot; standard marking methods (indelible ink, vibro-etching) include heat and lot numbers as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx,...

Open

4785

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

4786

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

4787

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

4788

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number as required, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

4789

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with required traceability and documentation for TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 -...

Open

4790

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 ...

Open

4791

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for required transverse testing. Source: DM...

Open

4792

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

4793

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and complete metallurgical and NDT res...

Open

4794

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/...

Open

4795

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4796

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

4797

3.1

AI

No

add date

AOD or equivalent steel refining is standard and required for 100% of production, and DMV 25.7N complies with the specified chemical composition in Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4798

3.1

AI

No

add date

DMV 25.7N (UNS S32760) chemical composition matches the requirements of Table 2 and complies with ASTM A790 and NORSOK MDS D51 Rev 06, including PREN ≥ 40 and all specified element limits. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest ...

Open

4799

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compliance with th...

Open

4800

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

4801

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and per 100 pieces, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/...

Open

4802

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes per ASTM A790 and NORSOK is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at the specified thi...

Open

4803

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with material meeting the tensile and maximum hardness properties of Table 4 as required for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

4804

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

4805

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

4806

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

4807

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

4808

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

4809

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report at actual magnification and with a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/...

Open

4810

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

4811

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully fulfilled. Source: DMV_STA...

Open

4812

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

4813

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

4814

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is specified and fulfilled for DMV 25.7N according to NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

4815

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4816

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including chemical composition, PRE, tensile, impact, corrosion, microstructure, ferrite content, and M-650 qualification for the specified wall thickness range. Source: ...

Open

4817

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours is performed for DMV 25.7N, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and DMV 25.7N complies with these requirements. Source: DMV_STANDARD_B...

Open

4818

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

4819

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is confirmed for the specified pipe dimensions, and 100% testing is performed after all processing. Calibration is expected to follow ASTM E213 Figure 3 as referenced by the standard. U...

Open

4820

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/...

Open

4821

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not validated; eddy current testing is not feasible for the required OD, and full compliance with required NDE methods (including ultrasonic and full-length dye pen...

Open

4822

5.2

AI

No

add date

No document confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair; NDE acceptance criteria per the requirement are not explicitly addressed or confirmed for the specified pipe dimension and ...

Open

4823

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the requested pipe, with no deviations or overrides specified by the customer. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - To...

Open

4824

7.0

AI

No

add date

ASTM A790 (6.1.3) and NORSOK MDS D51 (§13) both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4825

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

4826

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

4827

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

4828

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

4829

10.1

AI

No

add date

Supplier MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the requirement for qualification for t...

Open

4830

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body and provides traceable documentation (EN 10204 type 3.1 certificates) as required by SIR205 and specification section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

4831

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

4832

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice, heat number, chemical analysis results, solution annealing parameters, and results of all met...

Open

4833

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782, and there is no evidence of QTR/MPCR availability as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4834

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

4835

3.1

AI

No

add date

AOD or equivalent refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4836

3.1

AI

No

add date

DMV 25.7N (UNS S32760) chemical composition matches the requirements of Table 2 and complies with ASTM A790 and NORSOK MDS D51 Rev 06, including PREN ≥ 40 and all specified element limits. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest ...

Open

4837

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compliance with th...

Open

4838

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

4839

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

4840

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure, with specified locations and directions, is fulfilled for DMV 25.7N per NORSOK...

Open

4841

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with mechanical properties meeting Table 4 requirements (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%). Hardness testing is performed per ASTM A790 and results are provided. Sour...

Open

4842

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required by NORSOK MDS D51 Rev 6 and ASTM A790 for seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

4843

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

4844

4.3

AI

No

add date

DMV 25.7N fulfills NORSOK MDS D51 Rev 06 impact test requirements: Charpy V-notch at -46°C, minimum transverse (average/single) 45J/35J, longitudinal (average/single) 65J/50J, and sub-size reduction factors. The specified pipe dimensions allow for re...

Open

4845

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed according to ISO 17781, with specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

4846

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

4847

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

4848

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases. Source: DMV_STANDARD_BOOK/02...

Open

4849

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, reported at actual magnification and including a scale bar, if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - ...

Open

4850

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_ST...

Open

4851

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10µm, but does not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed, as required by the client specification. Source: DMV_STANDARD_BOOK/02-04...

Open

4852

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Sou...

Open

4853

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781, with specified etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact a...

Open

4854

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

4855

4.5

AI

No

add date

ASTM G48 Method 'A' corrosion testing at 50°C for 24h in accordance with ISO 17781 is not explicitly mentioned or evidenced; compliance cannot be confirmed. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4856

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/...

Open

4857

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781 corrosion test (G48 Method A @ 50°C, 24h). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

4858

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

4859

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available after all mechanical processing, and the pipe dimensions are within equipment capability. Reference notches per ASTM E213 are addressed. Source: DMV_STANDARD...

Open

4860

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT) is confirmed, but compliance with additional NORSOK M-630 MDS D51 or M-650/ISO 17782 requirements is not demonstrated. For OD 219.1 mm, Eddy current testing is not feasible, and hydrostatic/ultrasonic t...

Open

4861

5.2

AI

No

add date

The available documents do not explicitly confirm that any indication greater than the calibration notch is treated as a defect and that such pipe/tubing is rejected or repaired; specific NDE acceptance criteria and rejection/repair policies are not ...

Open

4862

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with OD, WT, and ovality tolerances confirmed for the requested dimensions, and no override specified by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General...

Open

4863

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790, requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring traceability as specified. Source: DMV_STANDARD_BOOK/02-03-01...

Open

4864

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4865

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

4866

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

4867

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

4868

10.2

AI

No

add date

No evidence confirms that documentation traceable to the products (SIR205) will be transmitted to TechnipFMC as required. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx, Certification Montbard plant.doc

Open

4869

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is issued and includes all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference). Source: DMV_STANDARD_BOOK/02-04-0...

Open

4870

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and results of all metallurgical and non-...

Open

4871

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all relevant chemical, mechanical, manufacturing, and testing requirements, and are M-650 qualified up to the required wall thickness. Source: DMV_...

Open

4872

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4873

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV25.7N, with manufacturing process qualified per NORSOK M-650/ISO 17782 and compliance with NORSOK M-630 MDS D51 Rev. 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produc...

Open

4874

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4875

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified by ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - ...

Open

4876

3.2

AI

No

add date

Solution annealing followed by accelerated cooling per ASTM A790 is confirmed, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is implicit in compliance wi...

Open

4877

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 and ISO 148-1 is feasible for the specified pipe dimensions, as the wall thickness exceeds the minimum required for both standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-...

Open

4878

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is carried out per lot, with 'lot' defined as per ASTM A790, fulfilling the requirement for one set per heat and heat treatment lot as specified. Source: DMV_STA...

Open

4879

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

4880

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations. For th...

Open

4881

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

4882

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

4883

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370/ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, meeting the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Im...

Open

4884

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C (transverse: avg 45 J, single 35 J; longitudinal: avg 65 J, single 50 J if transverse not possible). The specified pipe dimensions allow for required testing and fulf...

Open

4885

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

4886

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

4887

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

4888

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

4889

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos including actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

4890

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

4891

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

4892

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

4893

4.4.3

AI

No

add date

Acceptance criteria: etching methods, minimum 400X magnification, structure free from intermetallic precipitates (isolated precipitates <10µm and not distributed allowed), carbides/nitrides must be reported, acceptance based on impact and corrosion t...

Open

4894

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4895

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4896

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, with manufacturing and qualification processes compliant with NORSOK M-650/ISO 17782. Sour...

Open

4897

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, meeting the criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

4898

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

4899

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is fulfilled for the specified pipe dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements and testing sequence. Source: DMV_STANDARD_B...

Open

4900

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled; only ASTM A790/A999 NDE is detailed, and Montbard plant's standard NDE capabilities (hydrostatic, ultrasonic, eddy current, dye penetrant) are...

Open

4901

5.2

AI

No

add date

None of the provided sources explicitly confirm that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor do they specify acceptance criteria for NDE based on calibration notch indications for the r...

Open

4902

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standards (A790, A999), with no override specified by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to AS...

Open

4903

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4904

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

4905

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated in the specification for DMV 25.7N seamless pipe under NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

4906

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

4907

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

4908

10.1

AI

No

add date

Supplier is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the requirement for qualification for the specif...

Open

4909

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceable documentation as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03...

Open

4910

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided, including all information required by ASTM A790 and NORSOK M-630, and validated by Quality Control for mill inspection. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BO...

Open

4911

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, ladle analysis, solution annealing parameters, and results of all metallurgical and no...

Open

4912

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification and referenced documentation. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4913

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782; no evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4914

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N up to WT 31.75 mm, and the requirement is for WT 18.26 mm. The manufacturing process is qualified to NORSOK M-650/ISO 17782 and meets NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BO...

Open

4915

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4916

3.1

AI

No

add date

UNS S32760 chemical composition matches Table 2 requirements and is confirmed by supplier certification and heat analysis per ASTM A790 for DMV material. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-0...

Open

4917

3.2

AI

No

add date

Manufacturing process is qualified to NORSOK M-650/ISO 17782; solution annealing followed by accelerated cooling is performed per ASTM A790; furnaces and procedures are M-650 accredited for this grade and wall thickness; free circulation of heating/c...

Open

4918

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

4919

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and direct reference to Table 3, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

4920

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure, with specified locations and directions, is fulfilled for DMV 25.7N per NORSOK...

Open

4921

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the tensile and maximum hardness properties of Table 4. Hardness testing is also performed as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

4922

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

4923

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if transverse...

Open

4924

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed according to ISO 17781, with specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

4925

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORS...

Open

4926

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

4927

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

4928

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected, fulfilling the requirem...

Open

4929

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

4930

4.4.2

AI

No

add date

No provided documentation confirms that intermetallic phases and/or precipitates are completely prohibited when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10 µm, which does not meet the stricter client r...

Open

4931

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Sou...

Open

4932

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 at ≥400X magnification, with etching to detect intermetallic phases, nitrides, and carbides. Structure must be basically free from intermetallic precipitates; isolated precipitates allowed if not ...

Open

4933

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

4934

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or reported. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4935

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6: chemical composition (PRE ≥ 40), mechanical properties, corrosion resistance, microstructure, ferrite content (35-60%), and required tests; manufacturing process is M-650...

Open

4936

4.5

AI

No

add date

DMV 25.7N meets the corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours, with no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

4937

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

4938

5.2

AI

No

add date

NDE per ASTM A790 is detailed, but compliance with NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782 is not confirmed. For OD 219.1 mm, eddy current testing is not feasible except with multi-elements probe (at extra cost and pending technical confirmati...

Open

4939

5.2

AI

No

add date

The available documents do not confirm the NDE acceptance criterion that any indication greater than the calibration notch is a defect requiring rejection or repair, and standard NDE is not feasible for the requested OD at Montbard. Source: DMV_STAND...

Open

4940

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) as required, with no evidence of deviation or special tolerance request in the customer specification. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDAR...

Open

4941

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4942

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

4943

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

4944

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

4945

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

4946

10.1

AI

No

add date

Supplier MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the requirement for qualification for ...

Open

4947

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

4948

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference). Source: DMV_STANDARD_BOOK/02-04-0...

Open

4949

10.2

AI

No

add date

Documentation and certification requirements are not fully met: NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and all required test results are either missing or i...

Open

4950

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

4951

3.1

AI

No

add date

AOD or equivalent refining is used 100% for DMV 25.7N, and chemical composition complies with Table 2 requirements of ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4952

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compliance with th...

Open

4953

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

4954

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and direct reference to Table 3, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

4955

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled per NORSOK MDS D51/ASTM A790. Fo...

Open

4956

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and maximum hardness properties of Table 4. Hardness testing is performed per ASTM A790...

Open

4957

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and maximum hardness 310 HBW per NORSOK MDS D51 Rev 6 and ASTM A790 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

4958

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact ...

Open

4959

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal if transverse is not possible. The specified pipe dimensions allo...

Open

4960

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, fulfilling the requirement. Source: DMV_STANDARD...

Open

4961

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

4962

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

4963

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

4964

4.4.2

AI

No

add date

Micrographic examination at minimum 400x magnification is performed, with representative micrographs recorded and reported at actual magnification including a scale bar if intermetallic phases are not detected, at or near mid-wall thickness. Source: ...

Open

4965

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

4966

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not fully ...

Open

4967

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

4968

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781, with specified etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact a...

Open

4969

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

4970

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

4971

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements for ASTM A790 seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

4972

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

4973

5.1

AI

No

add date

No evidence is provided confirming NDE personnel are qualified and certified to ISO 9712 level II or III, nor are their roles and responsibilities defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Mo...

Open

4974

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

4975

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed; only ASTM A790/A999 NDE is detailed. For OD 219.1 mm, eddy current testing is not feasible, hydrostatic and ultrasonic tests are only available at extra co...

Open

4976

5.2

AI

No

add date

The referenced documents do not confirm the acceptance criterion that any indication greater than the calibration notch is a defect requiring rejection or repair, and for OD 219.1 mm, standard NDE methods are either not feasible or require extra cost...

Open

4977

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standards (A790, A999), with no overriding TechnipFMC specification indicated for the inquiry. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01...

Open

4978

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4979

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

4980

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

4981

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and meets the requirements of ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

4982

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

4983

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

4984

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, fulfilling supplier qualification documentation per SIR...

Open

4985

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

4986

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is issued and includes all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary or QTR nu...

Open

4987

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgic...

Open

4988

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Dige...

Open

4989

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782, as required. No evidence of QTR/MPCR documentation availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

4990

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, fulfilling the requirement for manufacturer and process qualification and compliance with...

Open

4991

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

4992

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

4993

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

4994

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for testing per heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

4995

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and explicit reference to Table 3, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 ...

Open

4996

4.1

AI

No

add date

DMV 25.7N seamless pipes are tested for tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure at specified thickness locations per NORSOK MDS D51/ASTM A790. For the ordered pi...

Open

4997

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with results meeting Table 4 requirements for NORSOK MDS D51/ASTM A790. Hardness testing is also performed and results are provided. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

4998

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) per NORSOK MDS D51 Rev 6 and ASTM A790 requirements for Table 4 mechanical properties. Source: DMV_STANDAR...

Open

4999

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the requested pipe dimensions (OD 219.1mm, WT 18.26mm), which exceed the minimum wall thickness requirements for these standards. Source: DMV_STANDARD_BOOK/12-03-02 - Impa...

Open

5000

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse average/single values of 45 J/35 J, minimum longitudinal average/single values of 65 J/50 J (if transverse not possible), a...

Open

5001

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, including etching for intermetallic phases and ferrite balance using the specified solution after final polishing. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

5002

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BOOK...

Open

5003

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

5004

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781, with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STAND...

Open

5005

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos including actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

5006

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

5007

4.4.2

AI

No

add date

The available specifications allow isolated intermetallic precipitates below 10 µm, but do not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed, as required by the client specification. Source: DMV_STANDARD_B...

Open

5008

4.4.3

AI

No

add date

Ferrite content is determined per ASTM E562 or ASTM E1245, performed in accordance with ISO 17781, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK...

Open

5009

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

5010

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is fulfilled for DMV 25.7N as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

5011

4.5

AI

No

add date

No information confirming corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5012

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive, micrographic, ferrite, corrosion, and impact tests, with required values confirmed and matched. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

5013

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m²; DMV 25.7N complies with these requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

5014

5.1

AI

No

add date

No information is provided confirming NDE personnel qualification or certification to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in M...

Open

5015

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available and applicable for the specified pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultrasonic testing...

Open

5016

5.2

AI

No

add date

NDE per ASTM A790/A999 is detailed, but explicit compliance with NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 is not confirmed. For OD 219.1 mm, eddy current testing is not feasible, and ultrasonic/hydrostatic tests are only available at extra cos...

Open

5017

5.2

AI

No

add date

None of the provided sources explicitly confirm that any indication greater than that produced by the calibration notch is treated as a defect and that defective pipe and tubing are rejected or repaired according to this criterion. Acceptance criteri...

Open

5018

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) as required, with no overriding specifications indicated by TechnipFMC. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances ac...

Open

5019

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5020

8.0

AI

No

add date

Marking per ASTM A790 includes traceability to melt and heat treatment lot; marking methods (indelible ink, vibro-etching) include heat number and DMV lot number, ensuring full traceability. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

5021

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

5022

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

5023

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body established within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

5024

10.1

AI

No

add date

Supplier is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, and QTR number is included in the certificate, fulfilling the requirement for NORSOK M-650/ISO 17782 qualification documentation for the specified size and pro...

Open

5025

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

5026

7.0

AI

No

add date

Both ASTM A790 and NORSOK MDS D51 Rev 06 require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5027

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is issued and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, 14-03 - Certification Montbard plant.doc

Open

5028

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice and refining method, heat number, chemical analysis results, solution annealing parameters, or results...

Open

5029

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02...

Open

5030

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782, as required. No evidence of QTR/MPCR availability is provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5031

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

5032

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 for DMV 25.7N grade. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5033

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and in accordance with ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MD...

Open

5034

3.2

AI

No

add date

Solution annealing followed by accelerated cooling per ASTM A790 is confirmed; manufacturing process and furnaces are qualified per NORSOK M-650/ISO 17782; free circulation of heating/cooling media is ensured by compliance with these standards. Sourc...

Open

5035

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

5036

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, directly referencing Table 3 for sampling as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM ...

Open

5037

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specifi...

Open

5038

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

5039

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength 750 MPa, yield strength 550 MPa, elongation 25%, and hardness max 310 HBW as required by NORSOK MDS D51 Rev 6 and Table 4 mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

5040

4.3

AI

No

add date

Pipe dimensions exceed minimum wall thickness required for Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1; testing is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12...

Open

5041

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability or full compliance with both standards as required by the specification. Source: DMV_STANDARD_BOOK/02-04-0...

Open

5042

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C with minimum transverse absorbed energy (average 45 J, single 35 J), and longitudinal (average 65 J, single 50 J) if transverse is not possible...

Open

5043

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, fulfilling the requirement. Source: DMV_STANDARD...

Open

5044

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

5045

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

5046

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

5047

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

5048

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

5049

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fulfilled. Source: DMV_STANDARD_BOOK/0...

Open

5050

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_ST...

Open

5051

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

5052

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is fulfilled for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5053

4.5

AI

No

add date

No information confirming corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5054

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

5055

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

5056

5.1

AI

No

add date

No information is provided confirming NDE personnel qualification or certification to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in M...

Open

5057

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

5058

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630/MDS D51 and NORSOK M-650/ISO 17782 are not confirmed; available documentation only details NDE per ASTM A790/A999, destructive tests, or limited NDE feasibility (eddy current not feasible for OD 219.1 mm, hydr...

Open

5059

5.2

AI

No

add date

No provided documentation explicitly confirms that indications greater than the calibration notch are considered defects requiring rejection or repair, and standard NDE methods are not feasible for the specified OD at Montbard. Source: DMV_STANDARD_B...

Open

5060

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as specified, with no overriding TechnipFMC requirements stated. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to A...

Open

5061

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: ASTM A790, NORSOK MDS D51 Rev 6

Open

5062

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790, ensuring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number identification, and certificates include heat treatment and steel meltin...

Open

5063

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

5064

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

5065

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

5066

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling supplier qualification documentation per SIR1...

Open

5067

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

5068

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is issued and includes all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary identific...

Open

5069

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or required metallurgical and non-destructive test results. EN 10204 3.1 certificates may...

Open

5070

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified for the required wall thickness. ...

Open

5071

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5072

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

5073

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5074

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits and PREN calculation as specified in Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 06 requirements for chemistry and minimum PREN value for S32760. Source: DMV_STANDARD_BOOK/02...

Open

5075

3.2

AI

No

add date

Solution annealing followed by accelerated cooling per ASTM A790 is confirmed; manufacturing process and furnace compliance with NORSOK M-650/ISO 17782 are met; free circulation of heating/cooling media is implicit in these standards. Source: DMV_STA...

Open

5076

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

5077

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-0...

Open

5078

4.1

AI

No

add date

DMV 25.7N seamless pipes are tested per NORSOK MDS D51/ASTM A790 for tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure, with correct specimen locations and directions. For...

Open

5079

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

5080

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required by NORSOK MDS D51 Rev 6 and ASTM A790 for seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

5081

4.3

AI

No

add date

Pipe dimensions exceed minimum wall thickness requirements for Charpy V-notch testing per ASTM A370 and ISO 148-1; testing is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

5082

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements for Charpy V-notch testing at -46°C, with minimum average/single values of 45/35 J (transverse) and 65/50 J (longitudinal) for thickness >6mm. The specified pipe dimensions all...

Open

5083

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, fulfilling the requirement. Source: DMV_STANDARD...

Open

5084

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is explicitly required for micrographic examination and matches the client's specification....

Open

5085

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

5086

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

5087

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos including actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

5088

4.4.2

AI

No

add date

Findings of intermetallic phases must be reported, and acceptance is based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

5089

4.4.2

AI

No

add date

The available documentation allows isolated intermetallic precipitates below 10μm and does not explicitly prohibit all intermetallic phases/precipitates when CVN testing cannot be completed, as required by the client specification. Source: DMV_STANDA...

Open

5090

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

5091

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 at ≥400X magnification, with etching to detect intermetallic phases, nitrides, and carbides. Structure must be basically free from intermetallic precipitates; isolated precipitates allowed if not ...

Open

5092

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

5093

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5094

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, microstructure, ferrite, manufacturing, heat treatment, and M-650 qualification for the specified wall thickness rang...

Open

5095

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

5096

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

5097

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available for the specified pipe dimensions, performed after all mechanical processing, heat treatment, and straightening. Calibration notches per ASTM E213 Figure 3 ar...

Open

5098

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not fulfilled; provided documentation only covers ASTM A790/A999 NDE, omits NORSOK-specific requirements, and indicates limited or non-standard NDE feasibility (eddy curr...

Open

5099

5.2

AI

No

add date

No provided documentation explicitly confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that this NDE criterion is standardly performed or feasible for the specified pipe dimension a...

Open

5100

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and ASTM A999 as specified, with no deviations or additional requirements indicated by TechnipFMC. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-0...

Open

5101

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-0...

Open

5102

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5103

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

5104

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

5105

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02...

Open

5106

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body and provides traceable documentation (EN 10204 type 3.1 certificates) for delivered products as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-...

Open

5107

10.2

AI

No

add date

EN 10204 Type 3.1 certificate will be issued and will include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary ...

Open

5108

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, metallurgical and non-destructive testing results. Only t...

Open

5109

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, D...

Open

5110

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm, cold finished up to WT = 10.925 mm), but not to ISO 17782 as required. No evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest...

Open

5111

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

5112

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 for DMV 25.7N grade. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5113

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed by heat analysis and supplier certification for DMV material. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

5114

3.2

AI

No

add date

Solution annealing followed by accelerated cooling per ASTM A790 and NORSOK M-650/ISO 17782 qualified procedures is confirmed for DMV 25.7N. Free circulation of heating/cooling media is implicit in compliance with these standards. Source: DMV_STANDAR...

Open

5115

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot, with lot defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spe...

Open

5116

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

5117

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes per ASTM A790/NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure tests at specified thickness locati...

Open

5118

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

5119

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required by NORSOK MDS D51 Rev 6 and ASTM A790 for seamless pipe specification. Source: DMV_STANDARD_BO...

Open

5120

4.3

AI

No

add date

Pipe dimensions exceed minimum wall thickness required for Charpy V-notch testing per ASTM and ISO standards; testing as specified is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.do...

Open

5121

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements: Charpy V-notch testing at -46°C, minimum transverse absorbed energy (average/single) 45 J/35 J, longitudinal (if transverse not possible) 65 J/50 J, and reduction factors for sub-size...

Open

5122

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, fulfilling the requirement. Source: DMV_STANDARD...

Open

5123

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect intermetallic phases, in accordance with ISO 17781, is explicitly required for micrographic examination, fulfilling the requirement for suitable etchants as listed in ISO 17781 Appendix B to show ferrite bal...

Open

5124

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

5125

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

5126

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

5127

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

5128

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not fulfil...

Open

5129

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_ST...

Open

5130

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition requirements, including PRE ≥ 40, as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5131

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

5132

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

5133

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5134

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

5135

4.5

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06, which requires no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781, G48 Method A at 50°C for 24 hours. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

5136

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

5137

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects is performed in accordance with ASTM E213 or ISO 10893-10 for the required pipe dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 ...

Open

5138

5.2

AI

No

add date

NDE per ASTM A790 is detailed, but compliance with additional NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 requirements is not confirmed. For the requested OD (219.1 mm), eddy current testing is not feasible, and hydrostatic and ultrasonic tests a...

Open

5139

5.2

AI

No

add date

No provided documentation confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, and NDE feasibility for the specified dimension is not guaranteed at the plant. Source: DMV_STANDARD_BOOK/02-...

Open

5140

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790) unless otherwise specified, and no alternative tolerances from TechnipFMC are stated or required in the provided context. Source: DMV_STANDARD_BOOK/07-...

Open

5141

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5142

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

5143

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 (§13, §14) for MST-Tubes and is fulfilled for DMV 25.7N seamless pipe per ASTM A790 and NORSOK M-630 MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

5144

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

5145

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

5146

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

5147

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body and provides EN 10204 type 3.1 certificates with traceability to delivered products, fulfilling the documentation and quality-assurance requirements of SIR205 and section 10.0. Source: DMV_STANDARD_...

Open

5148

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant specifications and manufacturing details. Source: DMV_STANDARD_BOOK/02-04-03 - Diges...

Open

5149

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. All other docum...

Open

5150

1.0

AI

No

add date

DMV 25.7N seamless pipe is offered, manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification and all relevant tests and certifications covered. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51...

Open

5151

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR documentation availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5152

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N with qualified manufacturing processes per M-650 or ISO 17782, and qualification testing meets NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

5153

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5154

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5155

3.2

AI

No

add date

Solution annealing followed by accelerated cooling per ASTM A790 is confirmed, with manufacturing and furnace qualification per NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is covered ...

Open

5156

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

5157

4.1

AI

No

add date

None of the provided documents include or outline the test specimen sampling details from Table 3 as required. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5158

4.1

AI

No

add date

Tensile, hardness, CVN (Charpy V-notch), corrosion, and microstructure tests are performed on prolongation samples of seamless pipes per ASTM A790 and NORSOK MDS D51 Rev 06, with tensile tests in longitudinal or transverse direction, CVN in transvers...

Open

5159

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, with mechanical properties (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and maximum hardness in accordance with Table 4 for NORSOK MDS D51/ASTM A790. DMV 25.7N complies with these...

Open

5160

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5161

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

5162

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness requirements for transverse specimens. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destru...

Open

5163

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -46°C, including minimum absorbed energy values and sub-size reduction factors. The specified pipe dimensions allow for required transverse and longitudinal Charpy V-notch testing a...

Open

5164

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants and electrolytic etching after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/...

Open

5165

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, is specified and matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

5166

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

5167

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

5168

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

5169

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

5170

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates if not distributed and <10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. The requirement is not fully met. Source: DMV_STANDAR...

Open

5171

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

5172

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impa...

Open

5173

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5174

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5175

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 (ASTM A790, NORSOK M-630, M-650/ISO 17782) are fully met, including compliance for destructive and microstructural tests (tensile, impact, corrosion, microstructure, ferrite) a...

Open

5176

4.5

AI

No

add date

Corrosion test for DMV 25.7N is performed as per ISO 17781: G48 Method A at 50°C for 24 hours, with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STA...

Open

5177

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

5178

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, which are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-0...

Open

5179

5.2

AI

No

add date

NDE methods (hydrostatic, ultrasonic, eddy current) are either not fully feasible for the specified pipe dimensions, only available at extra cost without confirmation, or not explicitly confirmed to meet NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/IS...

Open

5180

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor that such NDE acceptance criteria are standardly performed or feasible for the ...

Open

5181

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding TechnipFMC specification identified. Source: 07.01 - General information.doc, 07.03.01 - Tolerances according to ASTM A 312-01a A 376-02a A 790-02 (A 999-01).doc, 02...

Open

5182

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5183

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures ensures mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

5184

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

5185

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

5186

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers as specified in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

5187

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling supplier qualification documentation requirem...

Open

5188

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

5189

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

5190

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed to conform per heat analysis. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.do...

Open

5191

10.2

AI

No

add date

EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the actual steel producer. No evidence is provid...

Open

5192

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

5193

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

5194

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements, including Charpy V-notch testing at -466C with minimum absorbed energy values (transverse: 45 J average, 35 J single; longitudinal: 65 J average, 50 J single if transverse n...

Open

5195

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and if each is below 10µm, matching the requirement for distribution and size of intermetallic phases....

Open

5196

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness at 400x minimum, with actual magnification and scale bar if interme...

Open

5197

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

5198

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

5199

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation or metadata. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5200

4.5

AI

No

add date

Requirement for no pitting at 20X magnification and weight loss less than 1.0 g/m² is fulfilled per corrosion test section (§11) of NORSOK MDS D51 Rev 06, tested to ISO 17781 G48 Method A, with DMV 25.7N compliant to these criteria. Source: DMV_STAND...

Open

5201

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

5202

5.2

AI

No

add date

The specific NDE acceptance criterion requiring rejection or repair of pipes with indications greater than the calibration notch is not confirmed in the referenced standards or digests, and standard NDE is not available for the requested OD at Montba...

Open

5203

8.0

AI

No

add date

Marking per ASTM A790 includes heat and lot traceability; marking methods (indelible ink, vibro-etching) include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NO...

Open

5204

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

5205

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

5206

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

5207

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

5208

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceable documentation as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03...

Open

5209

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, including heat treatment condition, steel manufacturer, steel melting and refining practice, and NORSOK M-650/ISO17782 manufacturing summary...

Open

5210

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all required metallurgi...

Open

5211

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the 'Requested Positions' table and confirmed by the digest, including all mechanical, chemical, and testing requirements. Manufacturing is M-650 qualified f...

Open

5212

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence provided for availability of Qualification Test Records or full compliance with both NORSOK M-650/ISO 17782 as required. Source:...

Open

5213

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

5214

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5215

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

5216

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

5217

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

5218

4.1

AI

No

add date

Tensile, hardness, CVN (Charpy V-notch), corrosion, and microstructure tests are performed on prolongation samples for seamless pipes as specified, with tensile and CVN tests in the transverse direction per ASTM A790, and longitudinal if transverse i...

Open

5219

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

5220

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets or exceeds the required minimum tensile strength (750 MPa), yield strength (550 MPa), elongation (25%), and maximum hardness (310 HBW) per NORSOK MDS D51 Rev 6 and ASTM A790 for S32760. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

5221

4.3

AI

No

add date

Pipe dimensions exceed minimum wall thickness required for Charpy V-notch testing as per ASTM A370, ASTM A1058, or ISO 148-1; testing is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing...

Open

5222

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible), with sub-size reduction factors. The specifi...

Open

5223

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

5224

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

5225

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

5226

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

5227

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

5228

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

5229

4.4.2

AI

No

add date

No provided documentation confirms that intermetallic phases and/or precipitates are completely prohibited when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10μm, which does not meet the stricter client re...

Open

5230

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

5231

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), in line with NORSOK MDS D51 and client...

Open

5232

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation or metadata. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5233

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 explicitly states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5234

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 06 are fully met, including compliance for all required destructive and micrographic tests, and M-650 qualification for DMV 25.7N up to the specified wall thickness. Source: DMV_...

Open

5235

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

5236

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

5237

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

5238

5.2

AI

No

add date

NDE per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 is not confirmed; available documents only reference ASTM A790/A999 NDE or destructive tests. For OD 219.1 mm, eddy current is only feasible with multi-elements probe at extra cost and req...

Open

5239

5.2

AI

No

add date

No evidence that NDE acceptance criteria require rejection or repair of pipes with indications greater than the calibration notch; standard NDE methods are not feasible or only available at extra cost for the specified dimension at the plant. Source:...

Open

5240

6.0

AI

No

add date

Dimensional tolerances are specified as per the applicable ASTM standard (ASTM A790 referencing ASTM A999) for the relevant product dimensions, with no overriding requirements from TechnipFMC indicated in the provided context. Source: DMV_STANDARD_BO...

Open

5241

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be pickled or bright annealed, directly fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5242

8.0

AI

No

add date

Marking includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAND...

Open

5243

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

5244

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

5245

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for UNS S32760/DMV25.7N up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

5246

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO 17782 manufacturing summary or QTR number, are provided and fulfill the requirement for documentation traceable to delivered products as...

Open

5247

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and compliant with the specified standards. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

5248

10.2

AI

No

add date

Some documents state that EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 identification, melting practice, refining method, heat treatment condition, heat number, chemical analysis, and test results, but only the country of origin of t...

Open

5249

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

5250

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability or full compliance with essential variables and limitations per the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest ...

Open

5251

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

5252

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5253

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790 as required, with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 7...

Open

5254

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compliance with th...

Open

5255

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

5256

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

5257

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per NORSOK MDS D51/ASTM A790 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locati...

Open

5258

4.2

AI

No

add date

Tensile testing is performed at room temperature in accordance with ASTM A370 or ISO 6892-1, and the material meets the specified tensile and maximum hardness properties per Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

5259

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

5260

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

5261

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C, with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal. The specified pipe dimensions allow ...

Open

5262

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

5263

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect intermetallic phases, in accordance with ISO 17781, is explicitly required for micrographic examination, fulfilling the requirement for suitable etchants as listed in ISO 17781 Appendix B to show ferrite bal...

Open

5264

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

5265

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

5266

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

5267

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

5268

4.4.2

AI

No

add date

The available documents do not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed; isolated precipitates are still allowed, which does not meet the stricter client requirement. Source: DMV_STANDARD_BOOK/02-04-0...

Open

5269

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

5270

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Acceptance criteria: structure must be basically free from intermetallic precipitates (isolated precipit...

Open

5271

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

5272

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or specified; ASTM G48 and ISO 17781 are not mentioned in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests...

Open

5273

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spe...

Open

5274

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

5275

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

5276

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed on the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

5277

5.2

AI

No

add date

NDE per ASTM A790 is detailed, but compliance with NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 is not confirmed. Standard NDE capability for the required OD is not available at Montbard, and full-length dye penetrant testing is not offered as sta...

Open

5278

5.2

AI

No

add date

No provided documentation confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor is the specific NDE acceptance criterion detailed or confirmed as standard practice f...

Open

5279

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790/A999) for the specified pipe, with no overriding requirements from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_B...

Open

5280

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and supporting documentation. All relevant chemical, mechanical, manufacturi...

Open

5281

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

5282

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

5283

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, in compliance with ASTM A790 a...

Open

5284

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements for minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

5285

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if transverse is not p...

Open

5286

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants and electrolytic etching after final polishing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

5287

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

5288

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

5289

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs are included, noting and recording the presence and location of intermetallic phases. S...

Open

5290

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5291

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

5292

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK...

Open

5293

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

5294

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for material manufacturers as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dige...

Open

5295

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

5296

10.2

AI

No

add date

ISO 9001 certification is provided and documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, is traceable to the delivered products as required by SIR205 and section 10.0. Source: DMV_S...

Open

5297

10.2

AI

No

add date

Certification is provided to EN 10204 Type 3.1 and includes all information required by ASTM A790 and NORSOK M-630 for 25Cr Duplex Stainless Steel seamless pipe, including heat treatment condition, steel manufacturer, steel melting and refining pract...

Open

5298

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution annealing details, or results of required metallurgical...

Open

5299

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, meeting all specified requirements for 25 Cr Duplex stainless steel seamless pipes. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.do...

Open

5300

1.0

AI

No

add date

No explicit confirmation that the supplier is qualified for DMV 25.7N with 18.26 mm wall thickness per NORSOK M-650/ISO 17782, nor confirmation of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 -...

Open

5301

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

5302

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06....

Open

5303

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN requirements as per Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 6 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51...

Open

5304

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification will state heat treatment condition as per ASTM A790. Pipes are processed to ensure ...

Open

5305

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

5306

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

5307

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, is performed as required....

Open

5308

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, meeting the required tensile and maximum hardness properties of Table 4. Hardness testing is also performed as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

5309

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW, as specified by the client. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

5310

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Im...

Open

5311

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C, with minimum absorbed energy values for transverse and longitudinal directions, and the specified pipe dimensions allow for required testing directions and specimen ...

Open

5312

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

5313

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

5314

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

5315

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

5316

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

5317

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

5318

4.4.2

AI

No

add date

No provided document explicitly prohibits intermetallic phases and/or precipitates when CVN testing cannot be completed due to geometry or size; micrographic examination allows isolated intermetallics under certain conditions, and no alternative proh...

Open

5319

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

5320

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

5321

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

5322

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5323

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, with accredited manufacturing and qualification processes. Source: DMV_STANDARD_BOOK/02 - ...

Open

5324

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per NORSOK MDS D51 Rev 06 (ISO 17781, G48 Method A). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

5325

5.1

AI

No

add date

No evidence provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, or their roles and responsibilities. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard plant.doc, DMV_STANDARD...

Open

5326

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is confirmed for the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12...

Open

5327

5.2

AI

No

add date

NDE per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 is not confirmed; only ASTM A790/A999 NDE is referenced. For OD 219.1 mm, eddy current is not feasible, hydrostatic and ultrasonic testing are only available at extra cost and require technical ...

Open

5328

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair; NDE acceptance criteria and reject/repair policy are not explicitly stated for the requirement...

Open

5329

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding customer specification indicated. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ...

Open

5330

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5331

8.0

AI

No

add date

Marking is performed according to ASTM A790, requiring full traceability to melt and heat treatment lot, with mandatory marking of heat number and DMV lot number ensuring compliance. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

5332

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

5333

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

5334

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

5335

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system certified within the EEA and specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

5336

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for UNS S32760 / DMV25.7N up to the required wall thickness, fulfilling the requirement for qualification for the specified s...

Open

5337

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body and provides EN 10204 type 3.1 certificates traceable to the delivered products, fulfilling the requirement for a quality-assurance system and traceable documentation. Source: DMV_STANDARD_BOOK/02 -...

Open

5338

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

5339

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution annealing parameters, an...

Open

5340

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, as indicated in the product specifications and confirmed by detailed digests. M-650 qualification is also m...

Open

5341

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N but not to ISO 17782; full qualification to both NORSOK M-650/ISO 17782 is not demonstrated as required. Availability of QTR/MPCR is not confirmed. Source: DMV_STANDARD_BOOK/02-04-03 - Di...

Open

5342

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, fulfilling the requirement for manufacturer and process qualification and compliance with ...

Open

5343

3.1

AI

No

add date

AOD or equivalent refining is used and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5344

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and in accordance with ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MD...

Open

5345

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnace qualification per NORSOK M-650/ISO 17782. Accelerated cooling is equivalent to water quenching, and compliance with these standards ensu...

Open

5346

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

5347

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

5348

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

5349

4.1

AI

No

add date

Test sampling requirements for seamless pipes per ASTM A790 and NORSOK MDS D51, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations,...

Open

5350

4.2

AI

No

add date

Tensile testing is performed at room temperature in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

5351

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

5352

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

5353

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, with minimum absorbed energy values of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal. The specified pipe dimensions...

Open

5354

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching for intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and examination in accordance ...

Open

5355

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

5356

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

5357

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases as required. Source: DMV_STAN...

Open

5358

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

5359

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK/0...

Open

5360

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STAN...

Open

5361

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

5362

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

5363

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in accordance with ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

5364

4.5

AI

No

add date

ASTM G48 Method 'A' corrosion testing at 50°C for 24h in accordance with ISO 17781 is not explicitly mentioned or confirmed; compliance cannot be validated based on the available information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Mon...

Open

5365

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified per NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

5366

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 24h, 50°C) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

5367

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

5368

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available and applicable for the specified pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultrasonic testing...

Open

5369

5.2

AI

No

add date

NDE per ASTM A790/A999 is detailed, but there is no explicit confirmation of compliance with NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782 NDE acceptance criteria. For the specified OD (219.1 mm), standard NDE methods at Montbard are either not feas...

Open

5370

5.2

AI

No

add date

No evidence that NDE acceptance criteria require rejection or repair of any indication greater than that produced by the calibration notch; NDE method feasibility for the specified OD is also not confirmed for standard application at Montbard. Source...

Open

5371

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the specified pipe dimensions, with no deviations or special tolerances stated in the customer specification or context. Source: DMV_STANDARD_BOOK/07-01 - General inform...

Open

5372

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5373

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

5374

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

5375

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

5376

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, fulfilling the qualification requirement. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

5377

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to delivered products, fulfilling the requirement for a quality-assurance system and traceable documentation. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

5378

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced throughout the specification context and scope. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORS...

Open

5379

10.2

AI

No

add date

Most required documentation and certification items (NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, metallurgical and NDT results) are either missing or only genera...

Open

5380

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

5381

1.0

AI

No

add date

There is no explicit confirmation that the supplier is qualified according to NORSOK M-650/ISO 17782 for the exact product (DMV 25.7N, WT 18.26 mm), nor evidence of availability of the required Qualification Test Record/MPCR for review. The provided ...

Open

5382

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

5383

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard and required for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS...

Open

5384

3.1

AI

No

add date

Chemical composition for UNS S32760 conforms to Table 2 of ASTM A790, matching the specified limits, with heat analysis and supplier certification provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-0...

Open

5385

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

5386

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for each heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

5387

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, directly referencing the required table for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - De...

Open

5388

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests, with specified locations and directions, is fulfilled for DMV 25.7N per ...

Open

5389

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with results meeting the tensile and maximum hardness properties of Table 4. Hardness testing is also performed and results are provided. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

5390

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

5391

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness required for standard transverse specimens. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - D...

Open

5392

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for required testing directions and specime...

Open

5393

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

5394

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is specified as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NO...

Open

5395

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

5396

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

5397

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, reported at actual magnification and including a scale bar, if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - ...

Open

5398

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

5399

4.4.2

AI

No

add date

The digest of NORSOK MDS D51 Rev 06 allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed. No other relevant information addresses the r...

Open

5400

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

5401

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impa...

Open

5402

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

5403

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50°C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5404

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified per NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

5405

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

5406

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, which are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-0...

Open

5407

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD, eddy current testing is not feasible, and hydrostatic/ultrasoni...

Open

5408

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair; standard NDE methods are either not feasible or only generally referenced for the s...

Open

5409

6.0

AI

No

add date

Dimensional tolerances are confirmed as per the applicable ASTM standard (ASTM A790/A999) for the requested pipe dimensions, with no deviations or special tolerances specified by the customer or TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General i...

Open

5410

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5411

8.0

AI

No

add date

Marking per ASTM A790 and plant marking methods ensure mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSO...

Open

5412

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5413

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

5414

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

5415

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, and the QTR number is included as per M-650 qualification, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/...

Open

5416

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to products, fulfilling the requirement for documentation to be transmitted to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

5417

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 manufacturing summary/QTR number. Source: DMV_ST...

Open

5418

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C (transverse: 45/35 J, longitudinal: 65/50 J) for thickness >6mm; the specified pipe dimensions allow for required testing and fulfillment of these properties. Source:...

Open

5419

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or required metallurgical and non-destructive test results. Only the country of origin of...

Open

5420

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

5421

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR documentation availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

5422

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

5423

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5424

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed by heat analysis with supplier certification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Dige...

Open

5425

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650/ISO 17782. Proper heat treatment and compliance with these standards are ...

Open

5426

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

5427

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

5428

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse, longitudinal if not feasible), and corrosion/microstructure tests at specified thickness lo...

Open

5429

4.2

AI

No

add date

Tensile testing is performed at room temperature in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

5430

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

5431

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfills the requirement for the specified pipe dimensions and wall thickness according to ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

5432

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with specified etchants after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

5433

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is explicitly required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_...

Open

5434

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

5435

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

5436

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included at actual magnification and a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

5437

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

5438

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10 µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully fulfilled. Source: DMV_ST...

Open

5439

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

5440

4.4.3

AI

No

add date

Micrographic examination per ISO 17781 is specified, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with compliance to DMV 25.7N and...

Open

5441

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and fulfilled for DMV 25.7N according to NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

5442

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50°C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5443

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified per NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

5444

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

5445

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

5446

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

5447

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed. Provided documents only reference ASTM A790/A999 NDE or lack NDE details. For the required OD 219.1 mm, eddy current is not feasible, and hydrostatic...

Open

5448

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair; NDE acceptance criteria and standard availability for the specified dimension are n...

Open

5449

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no deviations or overrides specified by TechnipFMC or in the customer specification. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances ac...

Open

5450

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5451

8.0

AI

No

add date

Marking is performed per ASTM A790 §14 and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

5452

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

5453

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

5454

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

5455

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness for the specified size and product form. Source: DMV_STANDARD_BOO...

Open

5456

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produc...

Open

5457

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

5458

10.2

AI

No

add date

Most required documentation and certification elements (NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, metallurgical and NDT results) are not provided. EN 10204 3.1...

Open

5459

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, covering all standard and supplementary requirements, with M-650 qualification for the required wall thickness. Source: DMV_STANDARD_BOOK/02-...

Open

5460

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782; no evidence of QTR/MPCR availability or full compliance with both standards as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produc...

Open

5461

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, with manufacturing process qualified per NORSOK M-650 (or ISO 17782) and meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

5462

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5463

3.1

AI

No

add date

UNS S32760 chemical composition matches Table 2 of ASTM A790 as required, and DMV material composition conforms with supplier certification and heat analysis per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed d...

Open

5464

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, furnaces are qualified to NORSOK M-650/ISO 17782, and pipes are arranged to ensure free circulation of heating and cooling media during heat treatm...

Open

5465

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

5466

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-0...

Open

5467

4.1

AI

No

add date

Tensile, hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests are performed on prolongation samples from seamless pipes per ASTM A790 and NORSOK MDS D51, with test directions and thickness locations as specif...

Open

5468

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, with results meeting Table 4 requirements for NORSOK MDS D51/ASTM A790. Hardness testing is also performed as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

5469

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

5470

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

5471

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal if transverse is not possible. The specified pipe dimensions allow...

Open

5472

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

5473

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect intermetallic phases, in accordance with ISO 17781, is explicitly required for micrographic examination, fulfilling the requirement for suitable etchant(s) as listed in ISO 17781 Appendix B to show ferrite ...

Open

5474

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

5475

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5476

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

5477

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

5478

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 requires reporting of intermetallic phases, and acceptance is based on CVN and corrosion test results if such phases are present, fulfilling the requirement for centerline intermetallic stringers reporting and a...

Open

5479

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Zero-tolerance is not guaranteed by the available document...

Open

5480

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

5481

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

5482

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification digest. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Diges...

Open

5483

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the listed standards or documents. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5484

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements (free from intermetallics, with reporting of carbides/nitrides). Source: DMV_STANDA...

Open

5485

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per NORSOK MDS D51 Rev 06 (ISO 17781, G48 Method A). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

5486

5.1

AI

No

add date

No evidence provided regarding qualification or certification of NDE personnel to ISO 9712 level II or III, nor definition of their roles and responsibilities as per ISO 9712. Requirement not fulfilled based on available information. Source: DMV_STAN...

Open

5487

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

5488

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed; standard NDE methods (hydrostatic, EC, UT) per ASTM A790 are referenced but not fully validated for NORSOK-specific requirements. For OD 2...

Open

5489

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor is there confirmation that NDE is standardly applied for the requested dimensio...

Open

5490

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790) for the requested pipe dimensions, with no evidence of a different requirement from TechnipFMC or the customer specification. Source: DMV_STANDARD_BOOK...

Open

5491

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5492

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

5493

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

5494

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

5495

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

5496

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification for the...

Open

5497

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceable documentation as required by SIR205 and NORSOK M-650/ISO17782. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

5498

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and validated, including all information required by ASTM A790 and NORSOK M-630 such as heat treatment, steel manufacturer, melting and refining practice, and M-650/ISO17782 qualification summary. Source: DMV...

Open

5499

10.2

AI

No

add date

Most required documentation and certification details (NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, metallurgical and NDT results) are not provided. EN 10204 3.1 ...

Open

5500

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all standard and supplementary requirements. The manufacturing process is M-650 qualified for the required wall thickness. Source: ...

Open

5501

1.0

AI

No

add date

Supplier is qualified to NORSOK M-650 for DMV25.7N but not accredited to ISO 17782; no evidence provided for QTR/MPCR availability as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5502

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

5503

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5504

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5505

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

5506

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

5507

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

5508

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations, is fulfilled. For NPS 8 (OD 219.1 mm, WT 18.26 mm...

Open

5509

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

5510

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

5511

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact ...

Open

5512

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C (transverse: 45 J avg/35 J single, longitudinal: 65 J avg/50 J single, with sub-size reduction factors). The specified pipe dimensions allow for required transverse C...

Open

5513

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants and electrolytic etching after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/...

Open

5514

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

5515

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

5516

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

5517

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected, fulfilling the requirem...

Open

5518

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

5519

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

5520

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

5521

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

5522

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

5523

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5524

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including chemical composition, PRE, tensile, impact, corrosion, microstructure, ferrite content, and M-650 qualification for the specified wall thickness....

Open

5525

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

5526

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

5527

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects is performed in accordance with ASTM E213 or ISO 10893-10; acceptance of ASTM E213 implies compliance with calibration reference notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02...

Open

5528

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled. Standard NDE methods (EC, UT, hydrostatic) for the requested pipe size (OD 219.1 mm) are only available at extra cost or require special...

Open

5529

5.2

AI

No

add date

The specific NDE acceptance criterion that any indication greater than that produced by the calibration notch represents a defect, requiring rejection or repair, is not confirmed in the referenced documents. Additionally, standard NDE for OD 219.1 mm...

Open

5530

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a A...

Open

5531

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5532

8.0

AI

No

add date

Marking is performed according to ASTM A790 (§14) and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Diges...

Open

5533

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

5534

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

5535

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

5536

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification de...

Open

5537

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability information, fulfilling the requirement for documentation traceable to delivered products and transmittal to TechnipFMC. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

5538

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

5539

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or results of all required metallurgical and non-destructive testing for the specific ord...

Open

5540

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as required. Manufacturing is M-650 qualified for the specified wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

5541

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm, cold finished up to WT = 10.925 mm), but not to ISO 17782 as required. No evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Diges...

Open

5542

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

5543

3.1

AI

No

add date

AOD or equivalent refining is standard practice for DMV 25.7N, and chemical composition complies with the specified requirements in Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5544

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the requirement table and is confirmed to conform to ASTM A790 with supplier certification and heat analysis per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

5545

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

5546

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

5547

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

5548

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled per NORSOK MDS D51/ASTM A790. Fo...

Open

5549

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370, with mechanical properties and maximum hardness meeting Table 4 requirements for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

5550

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

5551

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement for wall thickness and testing standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive test...

Open

5552

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements, including Charpy V-notch testing at -46°C with minimum energy values (transverse: 45 J average/35 J single, longitudinal: 65 J average/50 J single) and reduction factors for ...

Open

5553

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

5554

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

5555

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 µm, matching the requirement for intermetallic phases and size limit. Source: ...

Open

5556

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

5557

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, actual magnification and scale bar reported, fulfilling the requirement for a representative micrograph at or near mid-wall thickness if intermetallic pha...

Open

5558

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

5559

4.4.2

AI

No

add date

The digest of NORSOK MDS D51 Rev 06 allows isolated intermetallic precipitates below 10μm, which does not meet the stricter client requirement of no intermetallic phases or precipitates if CVN testing cannot be completed. ASTM A790 does not address t...

Open

5560

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781...

Open

5561

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corro...

Open

5562

4.5

AI

No

add date

ASTM G48 Method 'A' corrosion testing at 50°C for 24h in accordance with ISO 17781 is not explicitly mentioned or referenced; compliance cannot be confirmed based on the available information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Mo...

Open

5563

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

5564

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per NORSOK MDS D51 Rev 06 (ISO 17781, G48 Method A). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

5565

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

5566

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is confirmed for the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12...

Open

5567

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. Standard NDE methods (EC, UT, hydrostatic) are not fully feasible for the requested OD at Montbard, and full-length dye penetrant testing ...

Open

5568

5.2

AI

No

add date

No evidence that NDE acceptance criteria require rejection or repair of indications greater than the calibration notch or that such NDE is standardly applied for the specified pipe dimensions at Montbard. No explicit confirmation of requirement fulfi...

Open

5569

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no overriding customer specifications or deviations stated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07...

Open

5570

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5571

8.0

AI

No

add date

Marking is per ASTM A790 §14 and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-...

Open

5572

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

5573

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

5574

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body established within the EEA, fulfilling the quality-assurance system requirement for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

5575

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified ...

Open

5576

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

5577

10.2

AI

No

add date

No explicit confirmation that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205 is provided in the reviewed sources. Certification and documentation practices are described, but transmission and traceabil...

Open

5578

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Cert...

Open

5579

10.2

AI

No

add date

EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MPCR number, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the act...

Open

5580

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification digest and the customer specification listing 'A790 NORSOK'. M-650 qualification is also met for the required ...

Open

5581

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of full qualification to both NORSOK M-650/ISO 17782 or availability of QTR/MPCR documentation for review as required by the spe...

Open

5582

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process follows M-650 (or ISO 17782) qualified procedures, fulfilling the requirement for manufacturer and process qualification and compliance...

Open

5583

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5584

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat, confirming conformity to the requireme...

Open

5585

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

5586

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

5587

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, directly referencing the required table for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - De...

Open

5588

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, all per ASTM A790 and NORSOK r...

Open

5589

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with mechanical properties meeting Table 4 requirements (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%), and hardness testing is also performed as specified. Source: DMV_STANDARD_...

Open

5590

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

5591

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

5592

4.3

AI

No

add date

DMV 25.7N meets NORSOK MDS D51 Rev 06 impact test requirements: Charpy V-notch at -46°C, minimum 45 J average and 35 J single in transverse, 65 J average and 50 J single in longitudinal if transverse not possible, with sub-size reduction factors. The...

Open

5593

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with etching for intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

5594

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

5595

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

5596

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

5597

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, actual magnification reported, and a scale bar included if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

5598

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

5599

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10μm, but the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Zero-tolerance is not guaranteed, so the requirement is not fulfil...

Open

5600

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

5601

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corr...

Open

5602

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in accordance with ISO 17781 and ASTM E1245, and compliance for DMV 25.7N is confirmed. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04...

Open

5603

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5604

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

5605

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 24h, 50°C) is performed for DMV 25.7N, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m²; DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

5606

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, or their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montba...

Open

5607

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

5608

5.2

AI

No

add date

NDE per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 is not confirmed; only ASTM A790/A999 NDE is detailed. For OD 219.1 mm at Montbard, eddy current is not feasible, hydrostatic and ultrasonic are only available at extra cost, and dye penetrant i...

Open

5609

5.2

AI

No

add date

None of the relevant documents confirm that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor do they confirm implementation of this NDE acceptance criterion for the specified pipe dimension at M...

Open

5610

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) as required, with no alternative tolerances specified by TechnipFMC or the customer request. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information....

Open

5611

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5612

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods include heat number and DMV lot number, ensuring compliance with the requirement. Source: DMV_STANDARD...

Open

5613

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

5614

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

5615

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

5616

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

5617

10.2

AI

No

add date

ISO 9001 certification is provided and documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, is traceable to the products and transmitted to TechnipFMC as required by SIR205. Source: DM...

Open

5618

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with issuance and validation by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

5619

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C (transverse: 45/35 J, longitudinal: 65/50 J). The specified pipe dimensions allow for required impact testing directions and specimen sizes. Source: DMV_STANDARD_BOOK/...

Open

5620

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and full metallurgical and non-destructive test results a...

Open

5621

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all material, manufacturing, testing, and qualification requirements. M-650 qualification is confirmed for the required wall thickness. Source: DMV_...

Open

5622

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability or full compliance with both NORSOK M-650/ISO 17782 as required by the specification. Source: DMV_STAND...

Open

5623

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

5624

3.1

AI

No

add date

AOD or equivalent refining is used 100% for DMV 25.7N, and chemical composition complies with Table 2 requirements of ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5625

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements, and heat analysis is performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A...

Open

5626

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

5627

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is carried out per lot, with 'lot' defined as per ASTM A790, fulfilling the requirement for one set per heat and heat treatment lot as specified. Source: DMV_STA...

Open

5628

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

5629

4.1

AI

No

add date

Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not feasible), and corrosion/microstructure at specified locations, are fulfilled. The ordered pipe dimension...

Open

5630

4.2

AI

No

add date

Tensile testing is performed at room temperature in accordance with ASTM A370, and the material meets the tensile and maximum hardness properties of Table 4 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

5631

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW, fulfilling all specified mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

5632

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact ...

Open

5633

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, with specified etchants (NaOH/KOH for intermetallics, oxalic acid or V2A plus NaOH/KOH for nitrides/carbides) used after final polishing as required....

Open

5634

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination and matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

5635

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

5636

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are reported with representative micrographs showing the presence and location of intermetallic phases. S...

Open

5637

4.4.2

AI

No

add date

Micrographs at a minimum magnification of 400x are included, reported at actual magnification with a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

5638

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

5639

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fulfilled by the availab...

Open

5640

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

5641

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

5642

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

5643

4.5

AI

No

add date

Corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is not explicitly confirmed or documented in the available information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5644

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, microstructure, solution annealing, ferrite content, absence of intermetallics, and required certification and qualificatio...

Open

5645

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, meeting the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest...

Open

5646

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

5647

5.2

AI

No

add date

DMV Germany has ultrasonic testing machines for the required dimensions and performs 100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 after all processing steps. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non...

Open

5648

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed or qualified. Standard NDE methods (EC, UT, hydrostatic) are either not fully feasible for the specified OD at Montbard or not confirmed as...

Open

5649

5.2

AI

No

add date

No explicit confirmation that NDE acceptance criteria based on calibration notch are applied or feasible for the specified pipe dimensions; referenced documents do not state the required rejection/repair criterion or confirm standard feasibility at M...

Open

5650

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per ASTM A790/A999 as required, with no overriding TechnipFMC specification indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 3...

Open

5651

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5652

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-0...

Open

5653

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

5654

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

5655

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

5656

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

5657

10.2

AI

No

add date

No evidence that documentation traceable to the products (SIR205) will be transmitted to TechnipFMC as required; only general certification and inspection processes are described without confirming compliance with the specific transmission and tracea...

Open

5658

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and will include all information required by ASTM A790 and NORSOK M-630; certificates are validated by Quality Control for mill inspection and comply with the referenced standards and documentation process....

Open

5659

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, actual chemical (ladle) analysis, solution annealing temperature/holding time/quench medium...

Open

5660

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all supplementary requirements, and are M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-03-01 - Diges...

Open

5661

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

5662

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5663

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed by heat analysis with supplier certification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Dige...

Open

5664

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

5665

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

5666

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

5667

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled per NORSOK MDS D51/ASTM A790. Fo...

Open

5668

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, meeting the tensile and maximum hardness properties of Table 4 for DMV 25.7N, with compliance confirmed for NORSOK MDS D51. Hardness testing is also performed as required. Sou...

Open

5669

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW, fulfilling Table 4 mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

5670

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

5671

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal if transverse not possible. The specified pipe wall thickness (18....

Open

5672

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants and electrolytic etching after final polishing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

5673

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH solution is specified for detecting ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

5674

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

5675

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

5676

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

5677

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

5678

4.4.2

AI

No

add date

No document fully prohibits intermetallic phases and/or precipitates when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10µm, which does not meet the stricter client requirement. Source: DMV_STANDARD_BOOK/0...

Open

5679

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

5680

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance is based on im...

Open

5681

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

5682

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or confirmed in the referenced documentation or standards list. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard pla...

Open

5683

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, and complies with NORSOK M-650/ISO 17782 qualification requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

5684

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781 (G48 Method A @ 50°C, 24h). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Diges...

Open

5685

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

5686

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 and ISO 10893-10 is confirmed for the specified pipe dimensions, matching the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12...

Open

5687

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled; only ASTM A790/A999 NDE is detailed. For the requested OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/ultrasonic t...

Open

5688

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor is there confirmation that the required NDE can be performed as standard for the specified dimen...

Open

5689

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (A790/A999) for the specified pipe size, with no evidence of override by TechnipFMC requirements or customer specification. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STA...

Open

5690

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5691

8.0

AI

No

add date

Marking is performed per ASTM A790 §14 and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

5692

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' (§ 13, § 14) for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

5693

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

5694

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

5695

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

5696

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

5697

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

5698

10.2

AI

No

add date

No provided document contains all required documentation and certification details, including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results...

Open

5699

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all standard, supplementary, and customer-specified requirements. M-650 qualification is confirmed for the required wall thickness....

Open

5700

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N (up to WT 31.75 mm) but not to ISO 17782; full qualification per requirement is not demonstrated. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5701

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, fulfilling the requirement for manufacturer and process qualification and compliance with ...

Open

5702

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard and required for 100% of production, and chemical analysis conforms to Table 2 for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5703

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed by supplier certification and heat analysis per ASTM A790 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dige...

Open

5704

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and furnace qualification and free circulation requirements are covered by these standards. Source: D...

Open

5705

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

5706

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dige...

Open

5707

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness l...

Open

5708

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 as required for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

5709

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

5710

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

5711

4.3

AI

No

add date

DMV 25.7N meets the impact test requirements at -466C with minimum absorbed energy values of 45 J (average) and 35 J (single) in the transverse direction, and 65 J (average) and 50 J (single) in the longitudinal direction if transverse is not possib...

Open

5712

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

5713

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, is specified for micrographic examination as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

5714

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

5715

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

5716

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

5717

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

5718

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size, so ...

Open

5719

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

5720

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

5721

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, meeting the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

5722

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5723

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and complies with ASTM A790, ISO 17781, and NORSOK M-650 standards. Source: DMV_STANDARD_B...

Open

5724

4.5

AI

No

add date

Corrosion test per ISO 17781 G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

5725

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

5726

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

5727

5.2

AI

No

add date

NDE per ASTM A790 is partially addressed (hydrostatic or NDE per ASTM A999), but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are fulfilled. For the requested OD, eddy current and u...

Open

5728

5.2

AI

No

add date

None of the reviewed documents explicitly confirm that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor do they confirm the feasibility of the required NDE methods for the specified pipe dime...

Open

5729

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no deviations specified in the customer documentation or drawings. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_...

Open

5730

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5731

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

5732

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5733

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

5734

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

5735

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

5736

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

5737

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

5738

10.2

AI

No

add date

EN 10204 Type 3.1 certificate will be issued and will include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary ...

Open

5739

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all required metallurgic...

Open

5740

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all standard and supplementary requirements, and are M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-03-01 - Digest A...

Open

5741

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782; no confirmation of QTR/MPCR documentation availability. Requirement for NORSOK M-650/ISO 17782 qualification and documentation is not fully fulfilled. Source: DMV_STANDARD_BOOK...

Open

5742

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

5743

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5744

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements, and heat analysis is performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A...

Open

5745

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

5746

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation or metadata. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5747

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

5748

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

5749

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per ASTM A790 and NORSOK r...

Open

5750

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

5751

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW for S32760. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

5752

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

5753

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible). The specified pipe dimensions allow ...

Open

5754

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

5755

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is explicitly required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_...

Open

5756

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

5757

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

5758

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

5759

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

5760

4.4.2

AI

No

add date

Specification allows isolated intermetallic precipitates below 10μm, but does not prohibit all intermetallic phases/precipitates when CVN testing cannot be completed, as required by the client specification. Zero-tolerance is not guaranteed in the ab...

Open

5761

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5762

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

5763

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance is based on im...

Open

5764

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5765

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5766

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, manufacturing, heat treatment, and qualification requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

5767

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

5768

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

5769

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

5770

5.2

AI

No

add date

NDE per ASTM A790 is feasible at Montbard for the specified OD and length, but only with extra cost for hydrostatic or ultrasonic testing; eddy current is not feasible for this OD. There is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/...

Open

5771

5.2

AI

No

add date

None of the referenced documents explicitly confirm that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair; specific NDE acceptance criteria are not detailed or confirmed for the r...

Open

5772

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a A ...

Open

5773

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5774

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

5775

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

5776

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

5777

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or specified. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5778

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

5779

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV 25.7N, and the EN 10204 type 3.1 certificate will include the NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, demonstrating qualification for the required size an...

Open

5780

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body and provides traceable EN 10204 type 3.1 certificates, fulfilling the requirement for a quality-assurance system and product traceability. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

5781

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO177...

Open

5782

10.2

AI

No

add date

Documentation may include NORSOK M-650/ISO 17782 identification, melting practice, heat treatment, heat number, chemical analysis, and test results, but the steel producer name is not provided (only country of origin), and there is no evidence that a...

Open

5783

1.0

AI

No

add date

DMV 25.7N seamless pipes are 25 Cr Duplex stainless steel, fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all relevant chemical, mechanical, manufacturing, and testing requirements. M-650 qualification is confirmed for the ...

Open

5784

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence provided for QTR/MPCR availability or full compliance with both standards as required by the specification. Source: DMV_STANDARD_...

Open

5785

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

5786

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5787

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the requirement table and DMV material composition conforms to this specification with heat analysis and supplier certification performed. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

5788

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

5789

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produc...

Open

5790

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - De...

Open

5791

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including chemical composition, PRE, tensile, impact, corrosion, microstructure, and ferrite content. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

5792

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, in accordance with ASTM A790 ...

Open

5793

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

5794

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

5795

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

5796

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C (transverse: 45/35 J, longitudinal: 65/50 J) for thickness >6mm, and the specified pipe dimensions allow for required testing orientation and values to be met and ver...

Open

5797

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

5798

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, is specified and fulfills the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

5799

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

5800

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

5801

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

5802

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

5803

4.4.2

AI

No

add date

No evidence that intermetallic phases and/or precipitates are completely prohibited when CVN testing cannot be completed; isolated precipitates are allowed per the digest, which does not meet the stricter client requirement. Source: DMV_STANDARD_BOOK...

Open

5804

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 ...

Open

5805

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with defined etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requirement for...

Open

5806

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

5807

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

5808

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

5809

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed or confirmed. For the specified OD, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at extra cost...

Open

5810

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair; NDE acceptance criteria and feasibility for the specified dimension are not demonstrated for Montbard plant or in refer...

Open

5811

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding TechnipFMC part report or drawing specified. Source: 07.01 - General information.doc, 07.03.01 - Tolerances according to ASTM A 312-01a A 376-02a A 790-02 (A 999-01)...

Open

5812

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5813

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and standard practice at Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_S...

Open

5814

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

5815

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

5816

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

5817

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified ...

Open

5818

10.2

AI

No

add date

No provided documentation explicitly confirms that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205. Traceability and transmission are not directly addressed or confirmed in the relevant sources. Source:...

Open

5819

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced throughout the specifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev ...

Open

5820

4.4.2

AI

No

add date

No relevant documents address the reporting or acceptance criteria for centerline intermetallic stringers, or link acceptance to CVN and corrosion test results in such cases.

Open

5821

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis (ladle analysis), solution annealing...

Open

5822

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with explicit confirmation of compliance for mechanical, chemical, and testing requirements for 25 Cr Duple...

Open

5823

1.0

AI

No

add date

No evidence of supplier qualification to NORSOK M-650/ISO 17782 for the exact product supplied or availability of QTR/MPCR documentation as required by the specification. MST-Tubes is M-650 accredited for DMV25.7N but not to ISO 17782, and other docu...

Open

5824

3.0

AI

No

add date

MST-Tubes F is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm), and qualification testing meets NORSOK M-630 MDS D51 rev. 6, fulfilling the requirement for manufacturer and process qualification and testing for DMV 25.7N with...

Open

5825

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N meets the chemical composition requirements of Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

5826

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the requested WT of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest ...

Open

5827

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed per ASTM A790, with manufacturing process and furnaces qualified according to NORSOK M-650 or ISO 17782, ensuring compliance with requirements including free circulation...

Open

5828

4.1

AI

No

add date

No evidence that impact, tensile, hardness, corrosion testing, and microstructure examinations are performed for each heat and heat treatment lot as defined in ASTM A790; required testing frequency and scope are not confirmed in the relevant document...

Open

5829

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

5830

4.1

AI

No

add date

Test sampling requirements for test direction, CVN testing, and thickness location are not fully addressed; tensile test direction and CVN impact testing are not specified, and detailed sampling locations are not confirmed for corrosion and microstru...

Open

5831

4.2

AI

No

add date

Tensile testing is performed per NORSOK MDS D51, which references ASTM A370 for mechanical testing, and the material meets or exceeds the tensile and hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

5832

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required for DMV 25.7N are not confirmed or addressed in the provided documentation; compliance cannot be validated with the available information. Source: DMV_STANDA...

Open

5833

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

5834

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the ordered pipe, as its wall thickness exceeds the minimum required for both ASTM and ISO standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive te...

Open

5835

4.3

AI

No

add date

Pipe dimensions allow for transverse Charpy V-notch specimens, so impact property requirements at -46°C are met for both transverse and longitudinal directions as specified. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/1...

Open

5836

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination according to ISO 17781 or specification of the required etchant solution for 25 Cr Duplex stainless steels is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testi...

Open

5837

4.4.1

AI

No

add date

No information confirming the use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination or to reveal ferrite balance and intermetallic phases is provided. Source: DMV_STANDARD_BOOK/12 - S...

Open

5838

4.4.2

AI

No

add date

The microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

5839

4.4.2

AI

No

add date

No evidence of recording the presence and location of intermetallic phases with micrographs at 400x magnification is provided; only grain size measurement is addressed or no relevant information is present. Source: DMV_STANDARD_BOOK/12 - Special Test...

Open

5840

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included at actual magnification and a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

5841

4.4.2

AI

No

add date

NORSOK MDS D41 Rev 06 and D51 Rev 06 allow isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not meet the stricter requirement that no intermetallic phases and/or precipitates are permitted if CVN t...

Open

5842

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided; only grain size measurement is addressed or the requirement is not mentioned at all. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

5843

4.4.3

AI

No

add date

No provided document specifies acceptance criteria or results for micrographic examination or metallurgical properties relevant to DMV 25.7N or the requirement context. Source: ASTM A 790.docx, NORSOK MDS S01 Rev 05.docx, Grain Size Examination in DM...

Open

5844

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5845

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) performed in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5846

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are provided or detailed in the referenced documents, so the requirement cannot be validated as fulfilled. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-...

Open

5847

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 G48 Method A at 25°C for 24 hours is required, with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the client's requirements. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

5848

5.1

AI

No

add date

No evidence provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, or their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDARD_BOOK/12-...

Open

5849

5.2

AI

No

add date

No explicit confirmation of 100% ultrasonic testing per ASTM E213 or ISO 10893-10 after all processing, nor evidence of required reference notch procedure as specified in the requirement is provided in the available documentation. Source: DMV_STANDAR...

Open

5850

5.2

AI

No

add date

100% qualitative anti-mixing PMI checks are standard at Montbard, with quantitative PMI and procedures available if specified, fulfilling general NDE acceptance criteria for PMI. Source: DMV_STANDARD_BOOK/12-06-06 - Positive Material Identification (...

Open

5851

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair of pipe and tubing, nor do they specify this acceptance criterion for NDE indications relative to ...

Open

5852

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for both hot and cold finished products are confirmed as per the applicable ASTM standards (including ASTM A 790 with A 999 for tolerances), with no deviations or exceptions stated for the relevant size ...

Open

5853

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and white pickled or bright annealed per NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790 diges...

Open

5854

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

5855

10.0

AI

No

add date

No evidence of an ISO 9001 quality-assurance system or certification by a competent EEA body is provided for the manufacturer or Montbard plant. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Certification Montba...

Open

5856

10.1

AI

No

add date

No evidence provided that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body with specific assessment for materials as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/1...

Open

5857

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N up to WT 31.75 mm (requested WT: 18.26 mm), and the EN 10204 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number. Source: DMV_STANDARD_...

Open

5858

10.2

AI

No

add date

No provided document confirms that documentation traceable to the products and to be transmitted to TechnipFMC (SIR205) will be delivered as required. No explicit evidence of compliance with the traceability and transmission requirement is present fo...

Open

5859

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control, fulfilling the requirement for certification and documentation per ASTM A790 and NORSOK M-630 for this grade and specification. Source: DMV_STANDARD_BOO...

Open

5860

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; the specified pipe dimensions allow for required transverse Charp...

Open

5861

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with 20-40% NaOH or KOH solution after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

5862

10.2

AI

No

add date

No provided document contains the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or test results. Only ge...

Open

5863

1.0

AI

No

add date

DMV 25.7N seamless pipes are 25 Cr Duplex stainless steel, manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, as confirmed by both the item table and technical digests. Source: DMV_STANDA...

Open

5864

1.0

AI

No

add date

Supplier is only M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) and not accredited to ISO 17782; no confirmation of QTR/MPCR documentation availability. Requirement for NORSOK M-650/ISO 17782 qualification and documentation is not f...

Open

5865

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

5866

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5867

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the requirement table and is confirmed to conform to ASTM A790 Table 2; heat analysis is performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01...

Open

5868

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

5869

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

5870

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling as outlined in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

5871

4.1

AI

No

add date

Test sampling requirements for tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations for seamless pipes are fulfilled for DMV 25.7...

Open

5872

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with mechanical properties and hardness requirements matching Table 4 and NORSOK MDS D51. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

5873

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

5874

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and is performed in accordance with the standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impa...

Open

5875

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782, as required. No evidence of QTR/MPCR availability is provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5876

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution for detecting ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

5877

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

5878

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

5879

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

5880

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK/0...

Open

5881

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

5882

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

5883

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corr...

Open

5884

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in accordance with ISO 17781 and ASTM E1245, and compliance for DMV 25.7N is confirmed. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04...

Open

5885

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is fulfilled; neither standard is explicitly mentioned or confirmed as performed in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- C...

Open

5886

4.5

AI

No

add date

DMV 25.7N complies with all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive, micrographic, ferrite, corrosion, and impact tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

5887

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 24h, 50°C) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

5888

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

5889

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is confirmed as available for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12...

Open

5890

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5891

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790 as required, with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 7...

Open

5892

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not addressed in the available documentation. For the specified OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only avail...

Open

5893

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair, and no evidence that NDE methods with this acceptance criterion are standardly available for the specified size at Mont...

Open

5894

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the requested pipe, with no overriding customer specification stated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances ...

Open

5895

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5896

8.0

AI

No

add date

Marking per ASTM A790 §16.1 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - ...

Open

5897

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' (§ 13, § 14) for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produc...

Open

5898

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

5899

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

5900

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demons...

Open

5901

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

5902

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

5903

10.2

AI

No

add date

Most required documentation and certification items (NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, metallurgical and non-destructive test results) are stated as in...

Open

5904

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all referenced mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified up to the required wal...

Open

5905

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

5906

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

5907

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

5908

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

5909

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, longitudinal if not possible), and corrosion/microstructure tests are performed at specified ...

Open

5910

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the specified tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

5911

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

5912

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements, including Charpy V-notch testing at -466C with minimum absorbed energy values (transverse: 45 J average/35 J single, longitudinal: 65 J average/50 J single) and reduction factors for...

Open

5913

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

5914

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

5915

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

5916

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

5917

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected, fulfilling the requirem...

Open

5918

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

5919

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

5920

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

5921

4.4.3

AI

No

add date

Micrographic examination is performed as per ISO 17781 with specified etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, and findings of carbides/nitrides reported. Acceptance...

Open

5922

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

5923

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5924

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5925

4.5

AI

No

add date

Corrosion test per ISO 17781 G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

5926

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

5927

5.2

AI

No

add date

Ultrasonic testing per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, performed after all mechanical processing, and includes reference notches as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destru...

Open

5928

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. Standard NDE methods (EC, UT, hydrostatic) for the required OD are only available at extra cost or require technical approval, with no con...

Open

5929

5.2

AI

No

add date

No provided document explicitly states that any indication greater than the calibration notch is considered a defect requiring rejection or repair, and standard NDE methods are not feasible for the requested OD at Montbard. Source: 02-03-01 - Digest ...

Open

5930

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the specified pipe, with no evidence of overriding requirements from TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - ...

Open

5931

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5932

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

5933

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

5934

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

5935

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

5936

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, and the QTR number is included in the certificate, fulfilling the requirement for supplier qualification documentation per SIR131. Source: DMV_STANDARD_BOOK/0...

Open

5937

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

5938

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 manufacturing summary/QTR number. ...

Open

5939

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, actual chemical analysis results, solution annealing parameters, or results of all required metallurgical and non-des...

Open

5940

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification digest and the position table listing 'A790 NORSOK' under customer specifications. Manufacturing is M-650 qualified for the...

Open

5941

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782 as required; no evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5942

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), with manufacturing and qualification testing meeting NORSOK M-630 MDS D51 Rev. 6 requirements and using M-650 (or ISO 17782) qualified procedures. Source: DMV_STAND...

Open

5943

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard and required for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

5944

3.1

AI

No

add date

DMV 25.7N (UNS S32760) chemical composition matches the requirements of Table 2 and complies with ASTM A790 and NORSOK MDS D51 Rev 06, including PREN ≥ 40 and all specified element limits. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest ...

Open

5945

3.2

AI

No

add date

Pipes are solution annealed followed by water quenching per ASTM A790, furnaces are qualified to NORSOK M-650/ISO 17782, and pipes are arranged to ensure free circulation of heating and cooling media during heat treatment including accelerated coolin...

Open

5946

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for each heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

5947

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

5948

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, fully aligning with ASTM A790 a...

Open

5949

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with results meeting the tensile and maximum hardness properties of Table 4. Hardness testing is also performed and results are provided. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

5950

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

5951

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement for wall thickness and testing standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive test...

Open

5952

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C: minimum 45/35 J (average/single, transverse) and 65/50 J (average/single, longitudinal) for thickness >6mm. The specified pipe dimensions allow for required transver...

Open

5953

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

5954

4.4.1

AI

No

add date

Etching with 20 to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

5955

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

5956

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

5957

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness when intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

5958

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

5959

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

5960

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

5961

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with required etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impac...

Open

5962

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06 digest. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev...

Open

5963

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

5964

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

5965

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per NORSOK MDS D51 Rev 06 (ISO 17781, G48 Method A). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

5966

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

5967

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultr...

Open

5968

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but compliance with additional NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 requirements is not demonstrated. For the specified OD (219.1 mm), standard NDE methods (eddy current, hydrostatic, ultrasonic) are not ava...

Open

5969

5.2

AI

No

add date

No provided documentation confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that such NDE acceptance criteria are standardly applied or feasible for the specified pipe size at Montb...

Open

5970

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the specified pipe, with no overriding customer specification indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Toleranc...

Open

5971

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

5972

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

5973

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

5974

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

5975

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

5976

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling supplier qualification documentation requirem...

Open

5977

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceable documentation as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03...

Open

5978

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided as standard and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control for mill inspection. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_S...

Open

5979

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and n...

Open

5980

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by both the item specification and the digest, covering all mechanical, chemical, corrosion, and qualification requirements. Source...

Open

5981

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782, and there is no confirmation of QTR/MPCR availability as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

5982

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

5983

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

5984

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PREN ≥ 40, as specified for ASTM A790 and NORSOK MDS D51 Rev 6. Chemical limits match those required and compliance is explicitly stated for DMV 25.7N. S...

Open

5985

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling (including water quenching) per ASTM A790; manufacturing process and furnaces are qualified to NORSOK M-650/ISO 17782; pipes are arranged to ensure free circulation of heating and cooling me...

Open

5986

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

5987

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

5988

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled per NORSOK MDS D51/ASTM A790. Fo...

Open

5989

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with tensile and maximum hardness properties meeting Table 4 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

5990

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: yield strength ≥ 550 MPa, tensile strength ≥ 750 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW, fulfilling all Table 4 mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

5991

4.3

AI

No

add date

Pipe dimensions exceed the minimum required wall thickness for Charpy V-notch testing as per ASTM and ISO standards; testing is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02...

Open

5992

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible), with sub-size reduction factors. The...

Open

5993

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

5994

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

5995

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

5996

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

5997

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

5998

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

5999

4.4.2

AI

No

add date

The referenced specifications either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates below 10µm, which does not meet the stricter client requirement of zero...

Open

6000

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

6001

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requirement for DMV 25....

Open

6002

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

6003

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, chemical composition, ferrite content, and corrosion/impact requirements. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

6004

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6005

4.5

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 requirements for pitting corrosion: no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781, G48 Method A at 50°C for 24 hours. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

6006

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

6007

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available and applicable for the specified pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultrasonic testing...

Open

6008

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled. Standard NDE methods (hydrostatic, ultrasonic, eddy current) are either not fully feasible for the requested OD (219.1 mm) or only avail...

Open

6009

5.2

AI

No

add date

None of the reviewed documents confirm the NDE acceptance criterion that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair; feasibility for required NDE methods is also not guaranteed...

Open

6010

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no deviations or overriding specifications stated by the customer or TechnipFMC, fulfilling the requirement. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/...

Open

6011

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6012

8.0

AI

No

add date

Marking per ASTM A790 and plant marking methods ensure mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDA...

Open

6013

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

6014

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system certified within the EEA and specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

6015

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body established within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

6016

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

6017

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

6018

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

6019

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include most required information (NORSOK M-650/ISO 17782 QTR number, steel melting practice, heat treatment, etc.), but only the country of origin of the steel supplier is provided, not the actual steel producer's ...

Open

6020

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification digest and the customer specification listing 'A790 NORSOK'. Manufacturing is M-650 qualified for the required...

Open

6021

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N but not to ISO 17782, as explicitly required. No confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

6022

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

6023

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev...

Open

6024

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6025

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

6026

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

6027

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling as outlined in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

6028

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure, is performed per NORSOK MDS D51/ASTM A790. For the specified pipe dimensions ...

Open

6029

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, meeting the required properties (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%), and hardness testing is performed with results in HRC, fulfilling the requirement. Source: DMV_STANDA...

Open

6030

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets the minimum requirements for tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as specified in NORSOK MDS D51 Rev 6 and ASTM A790. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

6031

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

6032

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, including minimum absorbed energy values for both transverse and longitudinal directions, sub-size specimen reduction factors, and testing procedures. The specified...

Open

6033

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6034

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants and electrolytic etching after final polishing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

6035

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH is specified for detecting ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

6036

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

6037

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

6038

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

6039

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK/0...

Open

6040

4.4.2

AI

No

add date

No provided document fully prohibits intermetallic phases and/or precipitates when CVN testing cannot be completed; NORSOK MDS D51 allows isolated precipitates below 10μm, which does not meet the stricter client requirement. Source: DMV_STANDARD_BOOK...

Open

6041

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

6042

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance is based on im...

Open

6043

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6044

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

6045

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, with compliance confirmed for each criterion and alignment with ASTM A790 and NORSOK quali...

Open

6046

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

6047

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

6048

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

6049

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/650 are not fully addressed. Provided documentation confirms NDE per ASTM A790 but lacks explicit evidence for NORSOK requirements. For OD 219.1 mm, eddy current testing is not feasible, ...

Open

6050

5.2

AI

No

add date

None of the reviewed documents confirm that indications greater than the calibration notch are treated as defects requiring rejection or repair, as specified by the requirement. No explicit NDE acceptance criterion matching the client specification i...

Open

6051

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (A790/A999) for the requested pipe, with no deviations or special requirements stated by the customer. Source: 07.01 - General information.doc, 07.03.01 - Tolerances according to ASTM A 312-...

Open

6052

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 require finished pipes to be pickled or bright annealed, fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6053

8.0

AI

No

add date

Marking is performed according to ASTM A790, requiring full traceability to melt and heat treatment lot, with mandatory marking of heat number and DMV lot number ensuring compliance. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

6054

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

6055

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

6056

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

6057

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, demonstrating qualification for the specified size and product ...

Open

6058

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

6059

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary or QTR...

Open

6060

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, melting practice, refining method, heat treatment condition, heat number, chemical analysis, and test results, but only the country of origin of the steel supplier is p...

Open

6061

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all material, manufacturing, and testing requirements, and are M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02-03-0...

Open

6062

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; full qualification to NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR is not confirmed for review by TechnipFMC upon...

Open

6063

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

6064

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06....

Open

6065

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed by heat analysis with supplier certification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Dige...

Open

6066

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

6067

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

6068

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the document directly referencing Table 3 for test specimen sampling as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 -...

Open

6069

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), corrosion, and microstructure tests at specified thickness locations, per NORSOK MDS D51/ASTM A790. ...

Open

6070

4.2

AI

No

add date

Tensile testing is performed at room temperature in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

6071

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

6072

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

6073

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C (transverse: 45 J avg/35 J single, longitudinal: 65 J avg/50 J single, sub-size reduction factors specified), and the specified pipe dimensions allow for required tr...

Open

6074

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching by 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and examination in accordance with ISO 17781 and the specified etchant. Source...

Open

6075

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is specified, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-0...

Open

6076

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

6077

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

6078

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

6079

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

6080

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, but does not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed, as required by the specification. Zero-tolerance is not establishe...

Open

6081

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

6082

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

6083

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

6084

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including compliance with destructive and microstructural tests (tensile, impact, corrosion, ferrite, microstructure) and required standards and values. Source: DMV_STAND...

Open

6085

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per NORSOK MDS D51 Rev 06 (ISO 17781, G48 Method A). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

6086

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

6087

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within capability range. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-0...

Open

6088

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782 NDE requirements are addressed. For the requested OD (219.1 mm), standard NDE (eddy current, ultrasonic, hydrostatic) is not available ...

Open

6089

5.2

AI

No

add date

No provided document specifies the acceptance criterion that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, nor confirms that such NDE is standardly performed or feasible for the ...

Open

6090

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding TechnipFMC specification indicated. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according t...

Open

6091

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6092

8.0

AI

No

add date

Marking includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAND...

Open

6093

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

6094

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

6095

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dige...

Open

6096

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

6097

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to delivered products, fulfilling the requirement for a quality-assurance system and traceable documentation as per SIR205. Source: DMV_STANDARD_BOOK/02 - S...

Open

6098

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

6099

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of required metallurgical and non-destructive testing for the specific orde...

Open

6100

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, meeting all chemical, mechanical, manufacturing, and testing requirements, and are M-650 qualified up to the required wall thickness. Source:...

Open

6101

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR documentation availability as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6102

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N within the specified wall thickness limits, and the manufacturing process follows M-650 (or ISO 17782) qualified procedures, meeting the requirement for manufacturer and process qualific...

Open

6103

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical analysis complies with Table 2 per ASTM A790 and NORSOK MDS D51 Rev 6 for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06...

Open

6104

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed by supplier certification and heat analysis per ASTM A790 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

6105

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

6106

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, with a frequency of 1/lot for each test type. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

6107

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

6108

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse, longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is performed as required by NORSOK MDS D51 and ...

Open

6109

4.2

AI

No

add date

Tensile testing is performed at room temperature per required standards, with mechanical properties and hardness meeting Table 4 and NORSOK MDS D51 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

6110

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

6111

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Im...

Open

6112

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C (transverse: 45 J avg/35 J single, longitudinal: 65 J avg/50 J single) for thickness ≥6 mm; the requested pipe dimensions allow for required transverse Charpy testing...

Open

6113

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, with specified etchants for intermetallic phases and ferrite balance applied after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

6114

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is explicitly required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_...

Open

6115

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

6116

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

6117

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

6118

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK/0...

Open

6119

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Zero-tolerance is not guaranteed by the available document...

Open

6120

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

6121

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

6122

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

6123

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

6124

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 are fully met, with DMV 25.7N compliant for all required destructive and micrographic tests, and qualified under NORSOK M-650 for the specified wall thickness. Source: DMV_STAN...

Open

6125

4.5

AI

No

add date

Requirement for no pitting at 20X magnification and weight loss less than 1.0 g/m² is met per ISO 17781 (G48 Method A @ 50°C, 24h) for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dige...

Open

6126

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

6127

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed after all processing steps, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non...

Open

6128

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not validated; only ASTM A790/ASTM A999 NDE is confirmed. For OD 219.1 mm, eddy current testing is not feasible, hydrostatic and ultrasonic tests are only available...

Open

6129

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are considered defects requiring rejection or repair, and no confirmation that the required NDE will be performed as standard for the requested size and specification. NDE a...

Open

6130

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are per ASTM A790 and ASTM A999 as required, with no deviations specified by TechnipFMC. Requirement is fulfilled as tolerances default to the applicable ASTM standard for the requested dimensions and pr...

Open

6131

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6132

8.0

AI

No

add date

Marking per ASTM A790 §14 and Montbard standard practices includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAN...

Open

6133

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

6134

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

6135

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

6136

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demonstration for th...

Open

6137

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

6138

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control for mill inspection and referencing M-650/ISO17782 qualification where applicable. Source: DMV_STANDARD_BOOK/02...

Open

6139

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or complete metallurgical and non-dest...

Open

6140

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all standard and supplementary requirements, and are M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-...

Open

6141

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence provided for availability of QTR/MPCR for review by TechnipFMC. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6142

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

6143

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 requirements for DMV 25.7N seamless pipe. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6144

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed by supplier certification and heat analysis per ASTM A790 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dige...

Open

6145

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling (including water quenching) per ASTM A790; manufacturing process and furnaces are qualified to NORSOK M-650/ISO 17782; pipes are arranged to ensure free circulation of heating and cooling me...

Open

6146

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

6147

4.4.3

AI

No

add date

Ferrite content specified as 35% to 60%, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6148

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

6149

4.1

AI

No

add date

All required test samplings for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure, with specified locations and directions, are fulfilled for DMV ...

Open

6150

4.2

AI

No

add date

Tensile testing is performed at room temperature in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

6151

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

6152

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible and fulfilled for the specified pipe dimensions, as wall thickness exceeds the minimum required for transverse specimens. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for ...

Open

6153

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for required testing directions. Source: D...

Open

6154

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching by 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and examination in accordance with ISO 17781 and the specified etchant. Source...

Open

6155

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

6156

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

6157

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

6158

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

6159

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

6160

4.4.2

AI

No

add date

No document specifies a zero-tolerance policy for intermetallic phases and/or precipitates if CVN testing cannot be completed; the closest reference allows isolated precipitates below 10μm, which does not meet the requirement for total prohibition in...

Open

6161

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

6162

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

6163

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallics, isolated precipitates <10µm, carbides/nitrides reported), with acceptance b...

Open

6164

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

6165

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, microstructure, PRE, solution annealing, and absence of intermetallics. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

6166

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

6167

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

6168

5.2

AI

No

add date

Ultrasonic testing per ASTM E213 and ISO 10893-10 is confirmed, performed after all mechanical processing, and applicable to the specified pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultr...

Open

6169

5.2

AI

No

add date

NDE per ASTM A790 is feasible, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD, eddy current testing is not feasible, and hydrostatic/ultrasonic testing ...

Open

6170

5.2

AI

No

add date

There is no explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor evidence that the required NDE acceptance criterion is implemented or feasible for the specified pipe dime...

Open

6171

6.0

AI

No

add date

Dimensional tolerances are confirmed as per the applicable ASTM standard (ASTM A790/A999) for the specified pipe, with no overriding requirements from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK...

Open

6172

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6173

8.0

AI

No

add date

Marking is performed per ASTM A790 §14 and includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_...

Open

6174

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

6175

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

6176

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

6177

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for UNS S32760/DMV25.7N up to the required wall thickness, fulfilling the qualification requirement for the specified size an...

Open

6178

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceable documentation as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03...

Open

6179

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and will include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control as per specification requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

6180

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution annealing parameters, or results of all required metall...

Open

6181

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all supplementary requirements and M-650 qualification, as specified. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOO...

Open

6182

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

6183

3.1

AI

No

add date

AOD or equivalent refining is used 100% for DMV 25.7N, and chemical analysis complies with Table 2 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

6184

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN requirements as per Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 6 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51...

Open

6185

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

6186

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, with a frequency of 1/lot for each test type, fulfilling the requirement. Source: DMV_STAND...

Open

6187

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

6188

4.1

AI

No

add date

Test sampling for seamless pipes per ASTM A790 and NORSOK MDS D51, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, is fu...

Open

6189

4.2

AI

No

add date

Tensile testing is performed at room temperature in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 as required for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

6190

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

6191

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6192

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact ...

Open

6193

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C, with minimum absorbed energy values for both transverse and longitudinal directions, and the specified pipe dimensions allow for required transverse Charpy V-notch te...

Open

6194

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with etching by 20-40% NaOH or KOH after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Di...

Open

6195

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

6196

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

6197

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

6198

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

6199

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

6200

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size. No other provided sources address or fulfill t...

Open

6201

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

6202

4.4.3

AI

No

add date

Micrographic examination per ISO 17781 is specified, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), in compliance with the requireme...

Open

6203

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6204

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

6205

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782 qualification, including chemical composition, mechanical properties, impact, corrosion, microstructure, and f...

Open

6206

4.5

AI

No

add date

Requirement for no pitting at 20X magnification and weight loss less than 1.0 g/m² is met per NORSOK MDS D51 Rev 06, which specifies ISO 17781 G48 Method A at 50°C for 24 hours with these acceptance criteria. DMV 25.7N complies with these criteria. S...

Open

6207

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

6208

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 and ISO 10893-10 is confirmed, and the requested pipe dimensions are within the testing machine's capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non des...

Open

6209

5.2

AI

No

add date

NDE per ASTM A790 is generally feasible, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD and length, eddy current and ultrasonic testing are onl...

Open

6210

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair; NDE acceptance criteria based on calibration notch are not specified for the requested pipe size, and feasibility of re...

Open

6211

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standards (ASTM A999), with no deviations specified by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances ...

Open

6212

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6213

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

6214

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 explicitly states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6215

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

6216

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

6217

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

6218

10.2

AI

No

add date

No evidence that the required documentation (SIR205) is transmitted to TechnipFMC and traceable to the delivered products as specified; available documents only reference general certification and traceability practices without confirming compliance ...

Open

6219

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 ...

Open

6220

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal. The specified pipe di...

Open

6221

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive te...

Open

6222

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, including chemical, mechanical, manufacturing, and testing requirements, with M-650 qualification up to the...

Open

6223

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782, which is explicitly required. No evidence of QTR/MPCR availability is provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6224

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

6225

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6226

3.1

AI

No

add date

UNS S32760 chemical composition matches Table 2 requirements and is confirmed by supplier certification and heat analysis per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-...

Open

6227

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

6228

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

6229

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

6230

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specifi...

Open

6231

4.2

AI

No

add date

Tensile and hardness testing are performed in accordance with ASTM A370 or ISO 6892-1, and the material meets the specified tensile and maximum hardness properties of Table 4 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

6232

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: yield strength ≥ 550 MPa, tensile strength ≥ 750 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

6233

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe size and wall thickness (>6mm, 18.26mm WT). Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 ...

Open

6234

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6235

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

6236

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases is required, in accordance with ISO 17781 Appendix B, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

6237

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

6238

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases. Source: DMV_STANDARD_BOOK/02...

Open

6239

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, reported at actual magnification and including a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

6240

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

6241

4.4.2

AI

No

add date

The available specifications allow isolated intermetallic precipitates below 10μm and do not prohibit all intermetallic phases and/or precipitates if CVN testing cannot be completed, which does not meet the stricter client requirement of zero toleran...

Open

6242

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

6243

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impa...

Open

6244

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

6245

4.5

AI

No

add date

No explicit confirmation that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or included in the referenced documents or standards. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant....

Open

6246

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO ...

Open

6247

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

6248

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testi...

Open

6249

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, which are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-0...

Open

6250

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD, eddy current and ultrasonic testing are only available at extra cost and...

Open

6251

5.2

AI

No

add date

No document confirms that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, nor is this NDE acceptance criterion stated for the specified pipe dimension at Montbard. NDE feasibility ...

Open

6252

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC indicated. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances accord...

Open

6253

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02...

Open

6254

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6255

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

6256

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

6257

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demonstration for th...

Open

6258

10.2

AI

No

add date

No evidence that documentation traceable to the products and required by SIR205 is transmitted to TechnipFMC as specified. Sources only mention general certification and inspection documents, not the specific requirement for SIR205 traceability and t...

Open

6259

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/...

Open

6260

10.2

AI

No

add date

Documentation does not provide all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, actual chemical analysis results, solution annealing temperature/h...

Open

6261

1.0

AI

No

add date

Supplier is M-650 accredited for DMV25.7N but not accredited to ISO 17782 as required; no confirmation of full qualification or QTR/MPCR availability per NORSOK M-650/ISO 17782 is provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

6262

8.0

AI

No

add date

Marking per ASTM A790 §16.1 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.do...

Open

6263

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, with manufacturing process qualified to NORSOK M-650 (or ISO 17782), and compliance with NORSOK M-630 MDS D51 Rev. 6 is confirmed. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

6264

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6265

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Heat analysis is performed per heat and compliance is explicitly stated for chemical composition re...

Open

6266

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

6267

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

6268

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ...

Open

6269

4.1

AI

No

add date

Tensile, hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests are performed on prolongation samples of seamless pipes per ASTM A790 and NORSOK MDS D51, with test directions and thickness locations as specifie...

Open

6270

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, with properties meeting NORSOK MDS D51 Table 4; hardness testing is also performed. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

6271

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

6272

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

6273

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements, including Charpy V-notch testing at -46°C with minimum absorbed energy values (transverse: 45 J average, 35 J single; longitudinal: 65 J average, 50 J single if transverse no...

Open

6274

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

6275

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

6276

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

6277

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

6278

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected, fulfilling the requirem...

Open

6279

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

6280

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size. No other relevant information provided support...

Open

6281

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

6282

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, including etching methods, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on...

Open

6283

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

6284

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 will be performed; neither standard is mentioned or confirmed in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in M...

Open

6285

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 06 are fully met, including compliance for tensile, impact, corrosion, ferrite, microstructure, PRE, solution annealing, and absence of intermetallics. Source: DMV_STANDARD_BOOK/...

Open

6286

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

6287

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

6288

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

6289

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. For OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at extra cost and require furth...

Open

6290

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, as specified in the requirement. NDE acceptance criteria and standard application f...

Open

6291

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the specified pipe, with no overriding tolerances stated in the customer specification or part report. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STA...

Open

6292

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

6293

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system certified within the EEA and specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

6294

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

6295

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified ...

Open

6296

10.2

AI

No

add date

No provided document explicitly confirms that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205. Certification and documentation types are mentioned, but not the specific transmission and traceability req...

Open

6297

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - ...

Open

6298

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice, heat number, chemical analysis results, solution annealing parameters, and results of all metal...

Open

6299

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with explicit confirmation of compliance for grade UNS S32760 and all relevant mechanical, chemical, and te...

Open

6300

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of QTR/MPCR availability for review by TechnipFMC as required by the specification. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

6301

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N within the specified wall thickness, and the manufacturing process is qualified per NORSOK M-650 (or ISO 17782), meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

6302

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes and DMV 25.7N meets the chemical composition requirements of Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - D...

Open

6303

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the inquiry for DMV 25.7N with WT = 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

6304

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no confirmation of QTR/MPCR availability. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6305

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed in accordance with ASTM A790, and the manufacturing process is qualified to NORSOK M-650/ISO 17782. Compliance with these standards ensures proper furnace operation and ...

Open

6306

4.1

AI

No

add date

No explicit confirmation that impact, tensile, hardness, corrosion testing, and microstructure examinations are performed for each heat and heat treatment lot as defined in ASTM A790. Only partial or unrelated information is provided in the relevant ...

Open

6307

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

6308

4.1

AI

No

add date

Test sampling details such as test direction, thickness location, and inclusion of CVN, hardness, corrosion, and microstructure tests per Table 3 are not confirmed in the referenced documents. Tensile test direction and CVN impact test requirements a...

Open

6309

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature with criteria meeting or exceeding Table 4 (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%), and maximum hardness is addressed. NORSOK MDS D51 refers to ASTM A790, which requires tensile testing per AS...

Open

6310

4.2

AI

No

add date

Mechanical property values for tensile strength, yield strength, elongation, and hardness for UNS S32760 are not provided; requirement cannot be validated as fulfilled based on available information. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

6311

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, meeting the minimum wall thickness requirements for both standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testi...

Open

6312

4.3

AI

No

add date

Impact testing at -46°C with required absorbed energy values is fulfilled for pipe with 18.26mm wall thickness, as transverse specimens are feasible and requirements are met. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/...

Open

6313

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination per ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels. Grain size examination is only discussed for austenitic materials and is not applicab...

Open

6314

4.4.1

AI

No

add date

No information provided confirms the use of 20-40% NaOH or KOH solution or other suitable etchant as per ISO 17781 Appendix B for micrographic examination to show ferrite balance and intermetallic phases. Source: DMV_STANDARD_BOOK/12 - Special Testin...

Open

6315

4.4.2

AI

No

add date

Micrographic examination requires the microstructure to be basically free from intermetallic phases, allowing isolated phases if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - S...

Open

6316

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided or addressed in the relevant documentation. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Mi...

Open

6317

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

6318

4.4.2

AI

No

add date

No relevant documents address the reporting or acceptance criteria for centerline intermetallic stringers or link acceptance to CVN and corrosion test results in such cases. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I.doc, DM...

Open

6319

4.4.2

AI

No

add date

Referenced documents allow isolated intermetallic precipitates below 10μm and do not fully prohibit intermetallic phases/precipitates if CVN testing cannot be completed, which does not meet the stricter client requirement of no intermetallic phases/p...

Open

6320

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided; only grain size measurement is addressed, not the required ferrite determination methods or standards. Source: DMV_STANDARD_BOOK/12 - S...

Open

6321

4.4.3

AI

No

add date

No acceptance criteria for micrographic examination or metallurgical properties are specified or addressed in the provided documents for DMV 25.7N or the specific inquiry. Procedures and standards are mentioned, but no actual acceptance criteria are ...

Open

6322

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6323

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or confirmed in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

6324

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are provided in the referenced documents or requirement section, making validation impossible. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03...

Open

6325

4.5

AI

No

add date

Pitting corrosion test per ISO 17781, G48 Method A at 25°C for 24 hours is required, with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the client's requirements. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

6326

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

6327

5.2

AI

No

add date

No evidence is provided that 100% ultrasonic testing for longitudinal defects will be performed in accordance with ASTM E213 or ISO 10893-10, nor that the specific calibration notch and test timing requirements are met. Source: DMV_STANDARD_BOOK/12 -...

Open

6328

5.2

AI

No

add date

Dye penetrant testing is performed on tube ends and bevels as per standard and client inquiry, and 100% qualitative anti-mixing PMI is conducted on standard production, fulfilling the NDE acceptance criteria for the Montbard plant. Source: DMV_STANDA...

Open

6329

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor is this acceptance criterion explicitly referenced for the requested product and NDE metho...

Open

6330

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N, with manufacturing processes qualified per NORSOK M-650 (or ISO 17782), and compliance with NORSOK M-630 MDS D51 Rev. 6 is referenced. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

6331

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the requirement table and is confirmed to conform to ASTM A790 Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 79...

Open

6332

6.0

AI

No

add date

Dimensional tolerances for OD and WT are confirmed as per the applicable ASTM standards (including ASTM A790/A999) for the specified product dimensions, with no deviations or special requirements indicated by TechnipFMC. Requirement is fulfilled as t...

Open

6333

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed (ASTM A790) and are specified as white pickled or bright annealed as standard (NORSOK MDS S01), directly fulfilling the requirement that finished pipes shall be white pickled or bright annealed. Sou...

Open

6334

8.0

AI

No

add date

Marking methods include both heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

6335

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS S01 Rev 05 for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 ....

Open

6336

10.0

AI

No

add date

No evidence of an ISO 9001 quality-assurance system or certification by a competent EEA body is provided for the material manufacturer or Montbard plant. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-01 - General information.doc, DMV_S...

Open

6337

10.1

AI

No

add date

No evidence that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body is provided; only inspection certificates and validation authorities are listed without confirming ISO 9001 certification as required by the ...

Open

6338

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, and the QTR number is included as per M-650 qualification, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/M...

Open

6339

10.2

AI

No

add date

No provided document confirms that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205. There is no explicit evidence of compliance with the traceability and transmission requirement for the delivered produ...

Open

6340

10.2

AI

No

add date

Material certificate is issued according to EN 10204 Type 3.1 and covers ASTM A790 and NORSOK M-630 information as referenced in the order specification. Source: 14-03 - Certification Montbard plant.doc

Open

6341

10.2

AI

No

add date

None of the reviewed documents provide the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or test results fo...

Open

6342

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all relevant chemical, mechanical, manufacturing, and testing requirements. M-650 qualification is confirmed for the required wall thickness. Sourc...

Open

6343

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent as standard practice, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6344

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and furnace qualification and free circulation of media are covered by these standards. Source: DMV_S...

Open

6345

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

6346

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

6347

4.1

AI

No

add date

All required destructive tests (tensile, hardness, CVN, corrosion, microstructure) for seamless pipes per NORSOK MDS D51/ASTM A790 are performed at the specified locations and directions. For the specified pipe dimensions (OD 219.1 mm, WT 18.26 mm), ...

Open

6348

4.2

AI

No

add date

Tensile and hardness testing are performed in accordance with ASTM A370 or ISO 6892-1, and the material meets the specified tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

6349

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets the minimum requirements for tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as specified in NORSOK MDS D51 Rev 6 and ASTM A790 for the grade requested. Source: D...

Open

6350

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

6351

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal, and the specified pipe dimensions allow for required transverse ...

Open

6352

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

6353

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

6354

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

6355

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

6356

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

6357

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

6358

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or specified. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

6359

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits all intermetallic phases and/or precipitates if CVN testing cannot be completed. No source fully prohibits intermetallics as required by th...

Open

6360

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

6361

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

6362

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev ...

Open

6363

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 are fully met for DMV 25.7N, including compliance with all required destructive and micrographic tests, and M-650 qualification up to the specified wall thickness. Source: DMV_...

Open

6364

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

6365

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

6366

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed on the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - U...

Open

6367

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. For the specified OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at extra cost. ...

Open

6368

5.2

AI

No

add date

No explicit confirmation that NDE acceptance criteria require rejection or repair of indications greater than the calibration notch; feasibility for required NDE is not confirmed for the specified dimension at Montbard. Source: DMV_STANDARD_BOOK/02-0...

Open

6369

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specifications from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A...

Open

6370

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6371

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

6372

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

6373

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

6374

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body as per the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

6375

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

6376

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

6377

10.2

AI

No

add date

Certification is provided to EN 10204 Type 3.1 and includes all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control and coverage of required details such as heat treatment, steel manufacturer, melting and refining p...

Open

6378

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis (ladle analysis), solution annealing...

Open

6379

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and are M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02-03-01 -...

Open

6380

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm, cold finished up to WT = 10.925 mm), but not to ISO 17782 as required. No evidence of QTR/MPCR documentation availability for review. Source: DMV_STANDARD_BOOK/02-...

Open

6381

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

6382

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6383

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6384

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

6385

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

6386

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

6387

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled per NORSOK MDS D51/ASTM A790. Fo...

Open

6388

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

6389

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets the minimum requirements for tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW/32 HRC) as specified in Table 4 for NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02...

Open

6390

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

6391

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements at -46°C, with minimum absorbed energy values for transverse and longitudinal directions, and the specified pipe dimensions allow for required testing directions and specimen sizes. Sou...

Open

6392

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants and electrolytic etching after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/...

Open

6393

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

6394

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

6395

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

6396

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

6397

4.4.2

AI

No

add date

Findings of intermetallic phases must be reported, and acceptance is based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

6398

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

6399

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

6400

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

6401

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev ...

Open

6402

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

6403

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified according to NORSOK M-650/ISO 17782. Source: Digest NORSOK MDS D51 Rev 06...

Open

6404

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6405

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

6406

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

6407

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed on the requested pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - U...

Open

6408

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not fully addressed. Available documentation confirms NDE per ASTM A790/A999 but lacks explicit evidence for NORSOK-specific requirements. Plant feasibility for req...

Open

6409

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor that such NDE acceptance criteria are standardly performed or feasible for the specified pipe si...

Open

6410

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are per ASTM A790 and ASTM A999, as required, with no alternative specifications from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Toleran...

Open

6411

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6412

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

6413

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

6414

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

6415

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

6416

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number as required, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

6417

10.2

AI

No

add date

No provided document explicitly confirms that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205. Certification and quality assurance are mentioned, but not the specific transmission and traceability requi...

Open

6418

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification summary. Source: DMV...

Open

6419

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6420

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive te...

Open

6421

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification listing and digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Di...

Open

6422

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

6423

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6424

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6425

3.2

AI

No

add date

Manufacturing process is qualified to NORSOK M-650, heat treatment is solution annealed followed by accelerated cooling per ASTM A790, furnaces comply with NORSOK M-650/ISO 17782, and process ensures free circulation of heating/cooling media around e...

Open

6426

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

6427

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

6428

4.1

AI

No

add date

Test sampling for seamless pipes per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, longitudinal if not possible), and corrosion/microstructure tests are performed as specified, with test l...

Open

6429

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

6430

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, fulfilling all Table 4 mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

6431

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

6432

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C (transverse: avg 5 J, single 5 J; longitudinal: avg 5 J, single 0 J if transverse not possible). The specified pipe dimensions allow for required transverse Char...

Open

6433

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

6434

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is required as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NO...

Open

6435

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

6436

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

6437

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

6438

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

6439

4.4.2

AI

No

add date

The available documentation does not prohibit all intermetallic phases and/or precipitates if CVN testing cannot be completed; isolated precipitates below 10μm are allowed, which does not meet the stricter client requirement that none are permitted i...

Open

6440

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

6441

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impa...

Open

6442

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

6443

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

6444

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified according to NORSOK and ASTM A790 standards. Source: DMV_STANDARD_BOOK/02...

Open

6445

4.5

AI

No

add date

Pitting corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours requires no pitting at 20X magnification and weight loss less than 1.0 g/m²; DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

6446

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

6447

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

6448

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6449

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD (219.1 mm), eddy current testing is not feasible, and hydrostati...

Open

6450

5.2

AI

No

add date

No provided document explicitly states that any indication greater than the calibration notch is considered a defect requiring rejection or repair, and standard NDE is not available for the requested OD at Montbard, so the requirement is not fulfille...

Open

6451

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790) for the specified pipe dimensions, with no overriding tolerances from TechnipFMC indicated in the request or documentation. Source: DMV...

Open

6452

7.0

AI

No

add date

ASTM A790 (6.1.3) and NORSOK MDS D51 (§13) both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6453

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot, and standard plant marking methods (indelible ink, vibro-etching) include heat and lot numbers as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Re...

Open

6454

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6455

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

6456

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

6457

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified s...

Open

6458

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to delivered products, fulfilling the requirement for documentation traceable to TechnipFMC deliveries. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

6459

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant standards and qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D...

Open

6460

10.2

AI

No

add date

Most required documentation and certification details (NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, metallurgical and NDT results) are stated as included or stand...

Open

6461

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N but not to ISO 17782, and there is no evidence of Qualification Test Records or Manufacturer Procedure Conformity Records being available as required. Full qualification to both NORSOK...

Open

6462

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

6463

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6464

3.1

AI

No

add date

No provided document contains the detailed chemical composition values for UNS S32760 or explicit confirmation that all specified maximums and ranges for each element are met; only general compliance or PREN confirmation is stated, which is insuffici...

Open

6465

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

6466

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

6467

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

6468

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per ASTM A790 and NORSOK r...

Open

6469

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

6470

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets or exceeds the required minimum tensile strength (750 MPa), yield strength (550 MPa), elongation (25%), and maximum hardness (310 HBW) per NORSOK MDS D51 Rev 6 and ASTM A790 for S32760. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

6471

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness requirements for transverse specimens. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destru...

Open

6472

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal. The specified pipe dimensions allo...

Open

6473

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with specified etchants for intermetallic phases and ferrite balance after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

6474

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

6475

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

6476

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and the presence and location of intermetallic phases are noted and recorded with micrographs. Source: DMV_STANDARD_BO...

Open

6477

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

6478

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

6479

4.4.2

AI

No

add date

No provided document fully prohibits intermetallic phases and/or precipitates when CVN testing cannot be completed due to geometry or size; the strict client requirement is not met as only limited precipitates are allowed in the referenced specificat...

Open

6480

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

6481

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance is based on im...

Open

6482

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6483

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

6484

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

6485

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

6486

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

6487

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within the machine's capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive...

Open

6488

5.2

AI

No

add date

NDE per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 is not confirmed. Only ASTM A790/A999 NDE is detailed, and for the requested OD (219.1 mm), eddy current is not feasible, while hydrostatic and ultrasonic tests are only available at extra...

Open

6489

5.2

AI

No

add date

No explicit confirmation that NDE acceptance criteria based on calibration notch indications are applied or feasible for the specified pipe dimensions; referenced standards and plant capabilities do not detail or guarantee this requirement is met for...

Open

6490

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782, as explicitly required. No evidence of QTR/MPCR availability is provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6491

6.0

AI

No

add date

Dimensional tolerances are confirmed as per the applicable ASTM standard (ASTM A790 referencing ASTM A999) for the specified pipe size, with no overriding customer specification indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DM...

Open

6492

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6493

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

6494

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

6495

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

6496

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dige...

Open

6497

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number as required, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

6498

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

6499

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification summary. Source: DMV_STANDARD_BOOK...

Open

6500

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and n...

Open

6501

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all standard and supplementary requirements. The product is 25 Cr Duplex stainless steel, and the manufacturing process is M-650 qu...

Open

6502

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to specified wall thicknesses) but lacks ISO 17782 accreditation, and there is no confirmation of QTR/MPCR documentation availability. Requirement for qualification to both NORSOK ...

Open

6503

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

6504

3.1

AI

No

add date

AOD or equivalent refining is used 100% for DMV 25.7N, and chemical composition complies with Table 2 of ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6505

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

6506

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and DMV material composition conforms with supplier certification and heat analysis per ASTM A790 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - ...

Open

6507

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

6508

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

6509

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

6510

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure, with specified locations and directions, is fulfilled for DMV 25.7N. For the o...

Open

6511

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with required tensile and hardness properties met as per NORSOK MDS D51 and Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

6512

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

6513

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and meets the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impa...

Open

6514

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements (Charpy V-notch at -46°C: transverse 45J/35J, longitudinal 65J/50J, sub-size reduction factors). The specified pipe dimensions allow for required transverse and longitudinal t...

Open

6515

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

6516

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

6517

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

6518

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

6519

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

6520

3.1

AI

No

add date

AOD or equivalent refining is required and used for 100% of production, and chemical analysis complies with Table 2 for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6521

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

6522

4.4.2

AI

No

add date

The digest of NORSOK MDS D51 Rev 06 allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed. ASTM A790 does not address this requirement. ...

Open

6523

4.4.3

AI

No

add date

Ferrite content is checked as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite determination methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

6524

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

6525

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

6526

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is fulfilled; neither standard nor test is mentioned or specified in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests i...

Open

6527

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

6528

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781 (G48 Method A @ 50°C, 24h). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Diges...

Open

6529

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

6530

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

6531

5.2

AI

No

add date

NDE per ASTM A790 is partially addressed with hydrostatic or NDE (EC or UT) per ASTM A999, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are fulfilled. For the requested OD (219....

Open

6532

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair, and no evidence that NDE methods are standardly applied for the specified dimensions at Montbard. Requirement not fulfi...

Open

6533

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a A ...

Open

6534

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6535

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

6536

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

6537

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

6538

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling supplier qualification documentation requirem...

Open

6539

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 manufacturing summary or QTR number, are provided and meet the requirement for transmission and traceability to TechnipFMC as per S...

Open

6540

10.2

AI

No

add date

Certification is provided to EN 10204 Type 3.1, including all information required by ASTM A790 and NORSOK M-630, and validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Cert...

Open

6541

10.2

AI

No

add date

Most documentation and certification requirements are stated as included (NORSOK M-650/ISO 17782 identification, melting practice, heat treatment condition), but the steel producer of the starting material is not fully fulfilled (only country of orig...

Open

6542

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, as confirmed by the specification digest and the customer specification listing 'A790 NORSOK'. Manufacturing is M-650 qualified for the required ...

Open

6543

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

6544

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSO...

Open

6545

3.1

AI

No

add date

No provided document lists or confirms the specific chemical composition limits for S32760 as required; only general compliance or PREN is referenced without explicit values for all elements in Table 2. Source: DMV_STANDARD_BOOK/02-03-01 - Digest AST...

Open

6546

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

6547

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

6548

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/...

Open

6549

4.1

AI

No

add date

Tensile, hardness, CVN (transverse, or longitudinal if not feasible), corrosion, and microstructure tests are performed on seamless pipes per ASTM A790 and NORSOK MDS D51 Rev 06, with the specified test directions and thickness locations. The pipe di...

Open

6550

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with tensile and hardness properties meeting Table 4 requirements for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spec...

Open

6551

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: Yield ≥ 550 MPa, Tensile ≥ 750 MPa, Elongation ≥ 25%, Hardness max 310 HBW/32 HRC, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

6552

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

6553

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements at -46°C, with minimum absorbed energy values of 45 J (transverse average), 35 J (transverse single), 65 J (longitudinal average), and 50 J (longitudinal single), and sub-size reduction...

Open

6554

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with etching by 20-40% NaOH or KOH after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Di...

Open

6555

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

6556

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

6557

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded as required. Source...

Open

6558

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report at actual magnification and with a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/...

Open

6559

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

6560

4.4.2

AI

No

add date

No provided document confirms the explicit prohibition of intermetallic phases and/or precipitates when CVN testing cannot be completed due to geometry or size; the NORSOK digest allows isolated intermetallic precipitates under certain conditions, an...

Open

6561

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

6562

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Acceptance: structure must be basically free from intermetallic precipitates (isolated precipitates allo...

Open

6563

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

6564

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

6565

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified per NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02-04-03 - Digest N...

Open

6566

4.5

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06, which requires no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781 G48 Method A, 50°C, 24h. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

6567

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destruct...

Open

6568

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, which are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-0...

Open

6569

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not fully addressed; only ASTM A790/A999 NDE is confirmed. For the requested OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/ultrasonic tests a...

Open

6570

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor is there confirmation that NDE is standardly applied for the requested dimensio...

Open

6571

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding TechnipFMC specification indicated. Source: 07.01 - General information.doc, 07.03.01 - Tolerances according to ASTM A 312-01a A 376-02a A 790-02 (A 999-01).doc, 02-03-01 -...

Open

6572

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6573

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring traceability as specified. Certification per EN 10204 3.1...

Open

6574

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

6575

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

6576

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

6577

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling supplier qualification documentation requirem...

Open

6578

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability, fulfilling the requirement for documentation and certification traceable to delivered products and transmitted to TechnipFMC as per SIR205. Source: DMV_STA...

Open

6579

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with issuance and validation by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

6580

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical...

Open

6581

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with explicit confirmation of compliance for mechanical, chemical, and testing requirements fo...

Open

6582

1.0

AI

No

add date

No evidence of supplier qualification to NORSOK M-650/ISO 17782 for the exact product supplied or availability of QTR/MPCR documentation. MST-Tubes is NORSOK M-650 accredited for DMV25.7N but not ISO 17782 accredited. Other documents do not address t...

Open

6583

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 (or ISO 17782), meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

6584

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N meets the chemical composition requirements of Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

6585

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the required WT of 18.26 mm for this inquiry. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

6586

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed in accordance with ASTM A790, the manufacturing process is qualified to NORSOK M-650/ISO 17782, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heat...

Open

6587

4.1

AI

No

add date

No provided document confirms that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790. Partial references to individual tests exist, but n...

Open

6588

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

6589

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no evidence of CVN, hardness, corrosion, or microstructure testing, nor confirmation of required test directions or thickness locations as specified in the requirement. Source: DMV_STANDARD_BOO...

Open

6590

4.2

AI

No

add date

Tensile testing is performed at room temperature with requirements for yield strength, tensile strength, and elongation, and DMV 25.7N complies with these properties. Hardness testing is also performed. Reference to NORSOK MDS D51 and compliance with...

Open

6591

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required for DMV 25.7N are not confirmed or are not met in the provided documents. ASTM A790 digest does not include the values, and the referenced TP316/TP316L prope...

Open

6592

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 explicitly states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6593

4.3

AI

No

add date

No evidence that Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is performed or that results meet Table 5 requirements for the specified product or order. Feasibility rules are mentioned, but compliance and execution are not confirmed...

Open

6594

4.3

AI

No

add date

Pipe dimensions allow both longitudinal and transverse Charpy V-notch impact specimens; impact testing at -466C with specified absorbed energies is feasible and can be fulfilled for this product. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for ...

Open

6595

4.4.1

AI

No

add date

No evidence of metallographic preparation or examination per ISO 17781, nor use of the specified etchant for 25 Cr Duplex stainless steels. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Micrographic Examination...

Open

6596

4.4.1

AI

No

add date

No evidence of etching with 20-40% NaOH or KOH solution or other suitable etchant as per ISO 17781 Appendix B for micrographic examination; only grain size measurement for austenitic materials is addressed, not duplex/super-duplex steels or the speci...

Open

6597

4.4.2

AI

No

add date

Micrographic examination requires the microstructure to be basically free from intermetallic phases, allowing isolated phases if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - S...

Open

6598

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided or addressed in the relevant documentation. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Mi...

Open

6599

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included at actual magnification and a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

6600

4.4.2

AI

No

add date

No provided documents address the reporting or acceptance criteria for centerline intermetallic stringers, nor their evaluation based on CVN or corrosion test results. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I.doc, DMV_STAN...

Open

6601

4.4.2

AI

No

add date

NORSOK MDS D41 and D51 allow isolated intermetallic precipitates below 10µm and not distributed over the whole specimen, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed. No other releva...

Open

6602

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided; only grain size examination is addressed, not ferrite content determination by the specified methods. Source: DMV_STANDARD_BOOK/12 - Sp...

Open

6603

4.4.3

AI

No

add date

No provided document specifies acceptance criteria or results for micrographic examination or metallurgical properties relevant to DMV 25.7N; micrographic examination is not addressed or is stated as not applicable to duplex/super-duplex grades in th...

Open

6604

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6605

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

6606

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are provided in the referenced documents or requirement section; only a heading is present without details or values for DMV 25.7N or the specified requirement. Source: DMV_STANDARD_BOOK/02...

Open

6607

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 G48 Method A at 25°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² are specified, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

6608

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

6609

5.2

AI

No

add date

No evidence of 100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10, or use of reference notches as specified, is provided in the relevant documentation. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive...

Open

6610

5.2

AI

No

add date

Dye penetrant testing is performed on tube ends and bevels on request, and 100% qualitative anti-mixing PMI is conducted on standard production, fulfilling the NDE requirement as specified by the client inquiry and standard practice. Source: DMV_STAN...

Open

6611

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor that this NDE acceptance criterion is standardly applied or feasible for the requested pipe dime...

Open

6612

6.0

AI

No

add date

Dimensional tolerances for OD and WT are confirmed as per the applicable ASTM standards (including ASTM A790/A999) for the relevant product dimensions, with no deviations or exceptions noted. Requirement is fulfilled by default to ASTM unless otherwi...

Open

6613

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and white pickled or bright annealed per NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790 diges...

Open

6614

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS S01 Rev 05 for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 ....

Open

6615

10.0

AI

No

add date

No evidence of an ISO 9001 quality-assurance system or certification by a competent EEA body is provided for the material manufacturer or Montbard plant. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

6616

10.1

AI

No

add date

No evidence that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body with specific assessment for materials as required by the specification. Source: DMV_STANDARD_BOOK/14-03 - Certification Montbard plant.doc

Open

6617

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

6618

10.2

AI

No

add date

No evidence that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205 is provided or confirmed. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-02 - Inspection Montbard plant....

Open

6619

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control for mill inspection, fulfilling the requirement for a Type 3.1 certificate. Reference to ASTM A790 and NORSOK M-630 is present in the order context, indi...

Open

6620

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, with minimum absorbed energy values for transverse and longitudinal specimens, and the specified pipe dimensions allow for required testing orientation and specimen...

Open

6621

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

6622

10.2

AI

No

add date

None of the reviewed documents provide the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, o...

Open

6623

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all referenced mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STA...

Open

6624

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability or full compliance with the essential variables and documentation requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NO...

Open

6625

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

6626

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6627

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed by supplier certification and heat analysis per ASTM A790 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dige...

Open

6628

3.2

AI

No

add date

Heat treatment is solution annealing followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650/ISO 17782. Pipes are arranged to ensure free circulation of heating and ...

Open

6629

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

6630

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling as outlined in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

6631

4.1

AI

No

add date

Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions, are ful...

Open

6632

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

6633

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

6634

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

6635

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

6636

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is explicitly required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_...

Open

6637

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

6638

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

6639

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

6640

4.4.2

AI

No

add date

Findings of intermetallic phases must be reported, and acceptance is based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

6641

4.4.2

AI

No

add date

No document states a zero-tolerance policy for intermetallic phases and/or precipitates if CVN testing cannot be completed; isolated precipitates below 10μm are allowed in one source, which does not meet the requirement for total prohibition in this ...

Open

6642

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard alignment. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

6643

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

6644

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

6645

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

6646

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements, as well as manufacturing, heat treatment, and qualification requirements. ...

Open

6647

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

6648

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

6649

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

6650

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782; no evidence provided for full qualification or QTR/MPCR documentation availability as required by the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

6651

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782-specific NDE requirements are not addressed. Standard NDE capability for the requested OD is not available at Montbard; eddy current and ultrasonic tests are on...

Open

6652

5.2

AI

No

add date

No provided documentation confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor is there confirmation that the required NDE can be performed as standard for the requ...

Open

6653

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standards (ASTM A999), with no overriding requirements specified in the context. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01...

Open

6654

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6655

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring compliance with the requirement. Source: DM...

Open

6656

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

6657

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

6658

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body established within the EEA, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

6659

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

6660

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, are provided as required for TechnipFMC and SIR205 traceability. Source: DMV_STANDARD_BOOK/02 ...

Open

6661

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - ...

Open

6662

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or actual metallurgical and non-destru...

Open

6663

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, manufacturing, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV...

Open

6664

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

6665

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6666

3.1

AI

No

add date

Chemical composition for UNS S32760 conforms to Table 2 of ASTM A790, matching the specified limits, with heat analysis and supplier certification provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-0...

Open

6667

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

6668

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

6669

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

6670

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations, in compliance with ASTM A790 and NORSOK ...

Open

6671

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with results meeting the required tensile and maximum hardness properties of Table 4. Hardness testing is also performed and results are provided. Source: DMV_STANDARD_BOOK...

Open

6672

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW as specified in Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

6673

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

6674

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with specified minimum absorbed energy values for both transverse and longitudinal directions. The pipe dimensions allow for standard transverse Charpy V-notch testi...

Open

6675

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

6676

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

6677

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

6678

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712.

Open

6679

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

6680

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

6681

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

6682

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully met. Source: DMV_S...

Open

6683

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

6684

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

6685

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

6686

4.5

AI

No

add date

No explicit confirmation that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or fulfilled in the provided documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

6687

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties, including destructive, micrographic, ferrite, corrosion, and impact tests as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 -...

Open

6688

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, meeting the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest...

Open

6689

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

6690

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within capability range. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02...

Open

6691

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT) is confirmed, but compliance with the specific NDE requirements of NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782 is not demonstrated. Eddy current testing is not feasible for the requested OD, and full...

Open

6692

5.2

AI

No

add date

No provided document confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor is the specific acceptance criterion or rejection policy stated. Additionally, standard NDE methods for the re...

Open

6693

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6694

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the specified pipe dimensions, with no deviations or special tolerances stated in the customer specification. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, ...

Open

6695

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6696

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

6697

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produc...

Open

6698

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

6699

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

6700

10.1

AI

No

add date

Certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR as required, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

6701

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products as required by SIR205 and NORSOK M-650/ISO17782. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

6702

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

6703

10.2

AI

No

add date

EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the actual steel producer name. Other required d...

Open

6704

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

6705

1.0

AI

No

add date

Supplier is M-650 accredited for UNS S32760 / DMV25.7N but not accredited to ISO 17782 as required; no evidence of QTR/MPCR availability or full compliance with NORSOK M-650/ISO 17782 qualification is provided. Source: DMV_STANDARD_BOOK/02-04-03 - Di...

Open

6706

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, the manufacturing process is qualified per M-650 (or ISO 17782), and qualification testing meets NORSOK M-630 MDS D51 Rev. 6 requirements. Source: DMV_STANDARD_BOOK/0...

Open

6707

3.1

AI

No

add date

AOD or equivalent refining is standard practice and used 100% for MST-Tubes, and DMV 25.7N complies with the specified chemical composition requirements in Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6708

3.1

AI

No

add date

Chemical composition for UNS S32760 conforms to Table 2 of ASTM A790, matching the specified limits and verified by heat analysis. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - D...

Open

6709

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

6710

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

6711

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, fulfilling the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detail...

Open

6712

4.1

AI

No

add date

Test sampling requirements for seamless pipes—including tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations—are fulfilled for DMV 25...

Open

6713

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

6714

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

6715

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

6716

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; the specified pipe dimensions allow for required transverse testing as per ...

Open

6717

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

6718

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect intermetallic phases, in accordance with ISO 17781, is explicitly required for micrographic examination, fulfilling the requirement for suitable etchants as listed in ISO 17781 Appendix B to show ferrite bal...

Open

6719

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

6720

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

6721

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

6722

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

6723

4.4.2

AI

No

add date

No evidence is provided that intermetallic phases and/or precipitates are completely prohibited when CVN testing cannot be completed; the referenced document allows isolated precipitates below 10µm, which does not meet the stricter client requirement...

Open

6724

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6725

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

6726

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

6727

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6728

4.5

AI

No

add date

Applicable standards are referenced, but there is no explicit confirmation that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or fulfilled. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montb...

Open

6729

4.5

AI

No

add date

All metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, microstructure, PRE, solution annealing, and absence of intermetallics, are fulfilled for DMV 25.7N with supporting test frequencies and st...

Open

6730

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

6731

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destruct...

Open

6732

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is confirmed for the specified pipe dimensions, with machine capability matching requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testi...

Open

6733

5.2

AI

No

add date

NDE per ASTM A790 is generally feasible, but NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782-specific NDE requirements are not explicitly addressed. For the requested OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/ultrason...

Open

6734

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair; NDE acceptance criteria and standard NDE application for the specified dimension are not demonstrated for Montbard plan...

Open

6735

6.0

AI

No

add date

Dimensional tolerances are confirmed as per the applicable ASTM standard (ASTM A790/A999) for the specified product, with no overriding TechnipFMC requirements indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07...

Open

6736

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6737

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02...

Open

6738

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

6739

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

6740

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, and QTR number is included as per M-650 qualification, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MCPR...

Open

6741

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

6742

10.2

AI

No

add date

Certification is provided to EN 10204 Type 3.1 and includes all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary or...

Open

6743

10.2

AI

No

add date

All required information, including NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, ladle chemical analysis, solution annealing details, and resu...

Open

6744

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified for the required wall thickness. Source: DMV_S...

Open

6745

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782, as required. No evidence of QTR/MPCR documentation availability. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6746

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

6747

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6748

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6749

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

6750

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

6751

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

6752

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests, with specified locations and directions, is fulfilled for DMV 25.7N per ...

Open

6753

4.2

AI

No

add date

Tensile testing is performed per ASTM A370, and material meets the tensile and maximum hardness properties of Table 4 (NORSOK MDS D51/ASTM A790). Hardness testing is also performed as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

6754

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and meets the requirement. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

6755

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

6756

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

6757

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for required transverse testing. Source: D...

Open

6758

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

6759

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is required for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

6760

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

6761

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

6762

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

6763

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

6764

4.4.2

AI

No

add date

No provided source confirms a zero-tolerance for intermetallic phases and/or precipitates when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10μm, which does not meet the stricter client requirement. Source...

Open

6765

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

6766

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 at ≥400X magnification; structure must be free from intermetallic precipitates except isolated ones <10µm, and carbides/nitrides are reported with acceptance based on impact and corrosion tests, m...

Open

6767

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

6768

4.5

AI

No

add date

Corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is not explicitly referenced or confirmed in the provided documentation or listed standards. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

6769

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified per NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

6770

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev ...

Open

6771

4.5

AI

No

add date

Corrosion test per ISO 17781 G48 Method A with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met for DMV 25.7N as per NORSOK MDS D51 Rev 06 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

6772

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within capability range. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-0...

Open

6773

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. For the requested OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at extra cost. Fu...

Open

6774

5.2

AI

No

add date

No referenced document explicitly confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair; NDE methods for the specified OD are not feasible as standard at the plant. Source: DMV_STANDARD_B...

Open

6775

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790/A999) for the requested pipe, with no overriding tolerances specified in the customer specification or part report/drawing. Requirement is fulfilled. Source: DMV_S...

Open

6776

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6777

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02...

Open

6778

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' confirming the requirement is met. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev...

Open

6779

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

6780

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

6781

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV25.7N up to 31.75 mm WT, covering the required 18.26 mm, and the EN 10204 type 3.1 certificate will include the NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number as requir...

Open

6782

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products being delivered as required by SIR205 and section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

6783

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

6784

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -46°C, with minimum absorbed energy values of 45 J (transverse average), 35 J (transverse single), 65 J (longitudinal average), and 50 J (longitudinal single), and the specified pip...

Open

6785

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

6786

10.2

AI

No

add date

No document provides all required documentation and certification details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis (ladle), solution annealin...

Open

6787

1.0

AI

No

add date

DMV 25.7N seamless pipes are confirmed as fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

6788

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 or availability of QTR/MPCR documentation; only M-650 accreditation is mentioned, not ISO 17782 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

6789

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N within the required wall thickness range, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_...

Open

6790

3.1

AI

No

add date

AOD or equivalent refining is standard for production and required for 100% of material; chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D...

Open

6791

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE 140, as per ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6792

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

6793

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

6794

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

6795

4.1

AI

No

add date

Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations, are fulfilled. The ord...

Open

6796

4.2

AI

No

add date

Tensile testing is performed at room temperature per required standards, and DMV 25.7N meets the specified tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

6797

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

6798

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for 18.26mm wall thickness and 219.1mm OD pipe as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impac...

Open

6799

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6800

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

6801

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

6802

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

6803

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are reported with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

6804

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

6805

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

6806

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fulfilled in this scenario. Sour...

Open

6807

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

6808

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

6809

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6810

4.5

AI

No

add date

No explicit confirmation that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or documented. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

6811

4.5

AI

No

add date

All metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, microstructure, PRE, solution annealing, and absence of intermetallics, are fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 -...

Open

6812

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

6813

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

6814

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

6815

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

6816

5.2

AI

No

add date

NDE requirements per ASTM A790 and NORSOK M-630 MDS D51 are not fully addressed; Montbard cannot perform eddy current testing for 219.1 mm OD, and hydrostatic/ultrasonic testing is only available at extra cost and not confirmed. Dye penetrant testing...

Open

6817

5.2

AI

No

add date

The specific NDE acceptance criterion that any indication greater than that produced by the calibration notch represents a defect, requiring rejection or repair, is not explicitly stated or guaranteed for the requested pipe dimensions. Standard NDE m...

Open

6818

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are confirmed to be per the applicable ASTM standards (including A999), with no evidence of override by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/0...

Open

6819

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6820

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

6821

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 explicitly states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6822

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

6823

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the specified quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

6824

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified ...

Open

6825

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 manufacturing summary or QTR number, are provided and fulfill the requirement for documentation traceable to delivered products as ...

Open

6826

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificat...

Open

6827

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive te...

Open

6828

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by both the item specification and supporting documentation. Manufacturing is M-650 qualified, and all relevant mechanical, chemical, and testin...

Open

6829

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; full qualification to both NORSOK M-650 and ISO 17782 is required. No evidence of QTR/MPCR documentation availability is provided. Source: D...

Open

6830

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

6831

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6832

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements. Heat analysis is performed per heat as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 ...

Open

6833

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

6834

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

6835

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

6836

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled for DMV 25.7N per NORSOK MDS D51...

Open

6837

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, with mechanical properties and hardness requirements matching Table 4 for NORSOK MDS D51/ASTM A790. DMV 25.7N complies with these requirements for both test methods and proper...

Open

6838

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

6839

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

6840

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, including minimum absorbed energies for both transverse and longitudinal directions, and the specified pipe dimensions allow for required testing directions and spe...

Open

6841

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

6842

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

6843

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

6844

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

6845

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, reported at actual magnification and including a scale bar, if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - ...

Open

6846

4.4.2

AI

No

add date

Presence of intermetallic stringers must be reported, and acceptance is based on CVN and corrosion test results, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

6847

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10µm and not distributed over the whole specimen, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or s...

Open

6848

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

6849

4.4.3

AI

No

add date

Micrographic examination is performed as per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Acceptance criteria: structure must be basically free from intermetallic precipitates (isolated precipi...

Open

6850

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

6851

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or confirmed in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

6852

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive, micrographic, corrosion tests, ferrite content, and heat treatment requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

6853

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A @ 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

6854

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destruct...

Open

6855

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed after all processing, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destr...

Open

6856

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE acceptance criteria are addressed. For the requested OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/...

Open

6857

5.2

AI

No

add date

No provided document explicitly states that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair; NDE acceptance criteria based on calibration notch are not detailed, and NDE is not stan...

Open

6858

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (A790/A999) for the specified pipe, with no overriding requirements from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Toleran...

Open

6859

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be pickled or bright annealed, fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.do...

Open

6860

8.0

AI

No

add date

Marking is performed per ASTM A790 §14 and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

6861

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

6862

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

6863

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

6864

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

6865

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with all required traceable documentation, fulfilling the requirement for documentation traceable to the products (SIR205) to be transmitted to TechnipFMC. Source: DMV_STANDA...

Open

6866

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference). ...

Open

6867

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution annealing parameters, or results of required metallurgi...

Open

6868

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all standard, supplementary, and testing requirements, and are M-650 qualified up to the required wall thickness. Source: DMV_STAND...

Open

6869

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence provided for QTR/MPCR availability for review by TechnipFMC as specified in the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

6870

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N within the required wall thickness range, and the manufacturing process follows M-650 (or ISO 17782) qualified procedures, fulfilling the requirement for manufacturer and process qualific...

Open

6871

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6872

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements, with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/0...

Open

6873

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

6874

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

6875

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-0...

Open

6876

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled. For the ordered pipe (OD 219.1 ...

Open

6877

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with tensile and hardness properties meeting Table 4 requirements for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spec...

Open

6878

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

6879

4.3

AI

No

add date

Pipe dimensions exceed minimum wall thickness required for Charpy V-notch testing as per ASTM A370, ASTM A1058, or ISO 148-1; testing is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products...

Open

6880

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal; pipe wall thickness (1...

Open

6881

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with etching by 20-40% NaOH or KOH after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Di...

Open

6882

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is explicitly required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_...

Open

6883

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

6884

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

6885

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected, fulfilling the requirem...

Open

6886

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

6887

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

6888

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates below 10μm, which does not meet the stricter client requirement of no interm...

Open

6889

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

6890

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corr...

Open

6891

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

6892

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

6893

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified according to NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

6894

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

6895

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

6896

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

6897

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed; only ASTM A790/A999 NDE is detailed, and plant feasibility for required NDE methods (eddy current, hydrostatic, ultrasonic, full-length dye penetrant) for ...

Open

6898

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair; NDE acceptance criterion is not specified for the requirement or for the requested pipe dimension at Montbard. NDE meth...

Open

6899

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790) unless otherwise specified, with no deviations or special requirements indicated by TechnipFMC for this inquiry. Source: DMV_STANDARD_BOOK/07-01 - Gene...

Open

6900

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be pickled or bright annealed, fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6901

8.0

AI

No

add date

Marking is performed per ASTM A790 §14 and includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_...

Open

6902

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6903

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

6904

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

6905

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling supplier qualification documentation requirem...

Open

6906

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, are provided and meet the requirement for documentation traceable to delivered products. Sourc...

Open

6907

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference). ...

Open

6908

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or required metallurgical and non-destructive test results. EN 10204 3.1 certificates ...

Open

6909

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, as specified in the inquiry and confirmed by the referenced digests. M-650 qualification is also met for th...

Open

6910

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N (up to WT 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability. Requirement for qualification to both NORSOK M-650/ISO 17782 and documentation availability is not full...

Open

6911

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, fulfilling the requirement for manufacturer and process qualification and compliance with ...

Open

6912

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed by supplier certification and heat analysis per ASTM A790 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dige...

Open

6913

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

6914

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

6915

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

6916

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified t...

Open

6917

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with mechanical properties meeting Table 4 requirements (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%), and hardness testing is also performed as required. Source: DMV_STANDARD_B...

Open

6918

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

6919

4.3

AI

No

add date

Pipe dimensions exceed minimum wall thickness required for Charpy V-notch testing as per ASTM A370, ASTM A1058, or ISO 148-1; testing is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing...

Open

6920

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if transverse is not po...

Open

6921

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchant solution, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

6922

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution for detecting ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

6923

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

6924

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included with the presence and location of intermetallic phases noted and recorded. Source: DMV_ST...

Open

6925

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

6926

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

6927

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. The stricter client requirement is not fully met by t...

Open

6928

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

6929

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

6930

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including PRE, tensile, impact, corrosion, microstructure, and ferrite content requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

6931

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and DMV 25.7N complies with these requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

6932

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

6933

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available and applicable for the specified pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultrasonic testin...

Open

6934

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the specified OD, eddy current testing is not feasible, and hydrostatic or ultrasonic test...

Open

6935

5.2

AI

No

add date

No provided document confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that NDE is performed as standard for the requested dimension at Montbard. Acceptance criteria and implementat...

Open

6936

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding TechnipFMC specifications indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A 376-...

Open

6937

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6938

8.0

AI

No

add date

Marking per ASTM A790 §16.1 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAN...

Open

6939

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spe...

Open

6940

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

6941

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

6942

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demons...

Open

6943

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to the delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

6944

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible and fulfilled for the specified pipe dimensions (WT 18.26mm > minimum required). Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact t...

Open

6945

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with issuance and validation by Quality Control at the Montbard plant clearly stated and referenced in the relevant documentation. Source:...

Open

6946

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or results of all required metallurgical ...

Open

6947

1.0

AI

No

add date

DMV 25.7N seamless pipes are 25 Cr Duplex stainless steel, fully compliant with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02-03-0...

Open

6948

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782; full qualification to both standards is required. No evidence of QTR/MPCR availability is provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spec...

Open

6949

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

6950

3.1

AI

No

add date

AOD or equivalent steel refining is required for 100% of production, and the chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 ...

Open

6951

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790 as required, with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 7...

Open

6952

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650/ISO 17782, and proper pipe placement during heat treatment is ensured. So...

Open

6953

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

6954

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

6955

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled per NORSOK MDS D51/ASTM A790. F...

Open

6956

4.2

AI

No

add date

Tensile testing is performed at room temperature per required standards, and DMV 25.7N meets the specified tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

6957

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW, fulfilling all specified mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

6958

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6959

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C, with minimum absorbed energy values for both transverse and longitudinal directions, and the specified pipe dimensions allow for required Charpy testing. Source: DMV...

Open

6960

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH solution after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

6961

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spe...

Open

6962

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

6963

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

6964

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report at actual magnification and with a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/...

Open

6965

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

6966

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

6967

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

6968

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

6969

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

6970

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

6971

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified according to NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

6972

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

6973

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destruct...

Open

6974

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

6975

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed. Standard NDE methods (eddy current, ultrasonic, hydrostatic) are not fully feasible or confirmed for the specified OD and length at Montbard. Full-le...

Open

6976

5.2

AI

No

add date

There is no explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor is there evidence that the required NDE acceptance criterion is standardly performed or feasible for the s...

Open

6977

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specifications from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a A...

Open

6978

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

6979

8.0

AI

No

add date

Marking is performed according to ASTM A790, requiring full traceability to melt and heat treatment lot, with mandatory marking of heat number and DMV lot number using approved methods such as indelible ink and vibro-etching. Source: DMV_STANDARD_BOO...

Open

6980

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

6981

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

6982

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

6983

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body and provides traceable documentation as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 R...

Open

6984

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51...

Open

6985

10.2

AI

No

add date

No provided documentation confirms the inclusion of all required items: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all requi...

Open

6986

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the 'Norms / Customer Specifications' and confirmed by the digest covering all relevant requirements. Source: Requested Positions table, DMV_...

Open

6987

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6988

1.0

AI

No

add date

No evidence of supplier qualification to NORSOK M-650/ISO 17782 or availability of QTR/MPCR; only M-650 accreditation is confirmed, not ISO 17782 as required by the specification. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STAND...

Open

6989

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N, with manufacturing processes qualified per NORSOK M-650 (or ISO 17782), and compliance with NORSOK M-630 MDS D51 Rev. 6 is referenced. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

6990

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6991

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

6992

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is e...

Open

6993

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

6994

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

6995

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure, with specified thickness locations, is fulfilled for DMV 25.7N. For NPS 8 (OD ...

Open

6996

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

6997

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

6998

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

6999

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for required transverse testing. Source: DM...

Open

7000

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified electrolytic etchant after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

7001

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, is specified for micrographic examination as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

7002

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

7003

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

7004

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

7005

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

7006

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. No evidence is provided that fully...

Open

7007

4.4.3

AI

No

add date

Ferrite content is measured by ASTM E1245 (default) or ASTM E562 (on request), in accordance with ISO 17781, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

7008

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corro...

Open

7009

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

7010

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

7011

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is compliant with NORSOK and ASTM A790 standards. Source: DMV_STANDARD_...

Open

7012

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

7013

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

7014

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed on the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - U...

Open

7015

5.2

AI

No

add date

NDE per ASTM A790 is partially addressed with 100% hydrostatic or NDE (EC or UT) per ASTM A999, but there is no explicit evidence of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782. For OD 219.1 mm, eddy current testing is only f...

Open

7016

5.2

AI

No

add date

None of the referenced documents explicitly confirm that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor do they confirm that the required NDE with this acceptance criterion...

Open

7017

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a A ...

Open

7018

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7019

8.0

AI

No

add date

Marking is performed according to ASTM A790, requiring full traceability to melt and heat treatment lot, with mandatory marking of heat number and DMV lot number ensuring compliance. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

7020

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

7021

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

7022

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demons...

Open

7023

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to delivered products, fulfilling the documentation and traceability requirements for TechnipFMC as specified in SIR205. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

7024

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and will include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control confirmed for the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

7025

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis (ladle), solution annealing parameters, and results of all required me...

Open

7026

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with explicit compliance to all relevant mechanical, chemical, and testing requirements. Source: DMV_STANDA...

Open

7027

1.0

AI

No

add date

No evidence of supplier qualification to NORSOK M-650/ISO 17782 for the exact product supplied or availability of QTR/MPCR documentation as required by the specification. MST-Tubes is NORSOK M-650 accredited for DMV 25.7N but not ISO 17782 accredited...

Open

7028

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to NORSOK M-650 with compliance to NORSOK MDS D51 Rev. 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

7029

3.1

AI

No

add date

AOD or equivalent is used 100% for DMV 25.7N, and the chemical composition complies with Table 2 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

7030

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the inquiry WT is 18.26 mm, within the accredited range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

7031

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed per ASTM A790, with manufacturing process and furnaces qualified according to NORSOK M-650 or ISO 17782, ensuring compliance with requirements including free circulation...

Open

7032

4.1

AI

No

add date

No explicit evidence that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790; only partial or unrelated information is provided in the rel...

Open

7033

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

7034

4.1

AI

No

add date

Test sampling requirements for test methods, directions, and locations, including CVN impact testing, are not fully specified or confirmed in the referenced documents. No explicit confirmation of compliance with the requirement table is provided for ...

Open

7035

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

7036

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) for DMV 25.7N are not provided or confirmed; referenced properties for other grades do not meet the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

7037

4.3

AI

No

add date

No evidence that Charpy V-notch testing is performed or meets ASTM A370, ASTM A1058, ISO 148-1, or Table 5 requirements; compliance with striker radius and test execution is not confirmed. Source: DMV_STANDARD_BOOK/02-02-01 Digest summary of ASTM A.d...

Open

7038

4.3

AI

No

add date

Pipe dimensions allow for transverse Charpy V-notch specimens; impact property requirements at -46°C are feasible and can be fulfilled for this product. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact test...

Open

7039

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination per ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels. Grain size examination is only discussed for austenitic materials, not duplex steels....

Open

7040

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchants as per ISO 17781 Appendix B for micrographic examination of ferrite balance and intermetallic phases in the provided documentation.

Open

7041

4.4.2

AI

No

add date

The micrographic examination section requires the microstructure to be basically free from intermetallic precipitates, allowing isolated precipitates if not homogeneously distributed and each is below 10 μm, matching the client's requirement exactly....

Open

7042

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided or addressed in the relevant documents or comments. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03...

Open

7043

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at 400x minimum magnification with a scale bar and actual magnification when intermetallic phases are not detected as required by the specification. S...

Open

7044

4.4.2

AI

No

add date

No relevant documents address the reporting or acceptance criteria for centerline intermetallic stringers or link acceptance to CVN and corrosion test results if such stringers are present. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination ...

Open

7045

4.4.2

AI

No

add date

NORSOK MDS D41 Rev 06 and D51 Rev 06 allow isolated intermetallic precipitates below 10µm even if CVN testing cannot be completed, which does not meet the stricter client requirement of no intermetallic phases or precipitates permitted in such cases....

Open

7046

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided or addressed in the relevant documents or comments. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 ...

Open

7047

4.4.3

AI

No

add date

No acceptance criteria or results for micrographic examination are provided or applicable for DMV 25.7N (super-duplex stainless steel); grain size examination is not required for this material type and is not addressed in the referenced standards or ...

Open

7048

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and confirmed for DMV 25.7N. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7049

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided. Referenced standards do not confirm fulfillment of this requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant....

Open

7050

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are provided; only a placeholder statement is present, so fulfillment cannot be validated based on the available information. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DM...

Open

7051

4.5

AI

No

add date

Specification requires pitting corrosion test per ISO 17781 G48 Method A at 25°C for 24 hours, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², matching the client's requirements. Source: DMV_STANDARD_BOOK/02 - ...

Open

7052

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDA...

Open

7053

5.2

AI

No

add date

No explicit confirmation of 100% ultrasonic testing per ASTM E213 or ISO 10893-10, calibration notches, or testing after all processing steps is provided. Only dimensional feasibility for ultrasonic testing is mentioned, not fulfillment of the requir...

Open

7054

5.2

AI

No

add date

100% qualitative anti-mixing PMI check is performed on standard production at Montbard using appropriate instruments, fulfilling the general NDE requirement for PMI. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02...

Open

7055

5.2

AI

No

add date

No provided document confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor is there confirmation that the required NDE is standardly performed or feasible for the specified dimensions a...

Open

7056

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for hot and cold finished products are specified as per the applicable ASTM standards (including A 790 with A 999, A 213, A 268, A 269, A 312, A 376, and A 511) for the relevant dimensions, with no overr...

Open

7057

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and white pickled or bright annealed per NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: Digest ASTM A 7...

Open

7058

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/13 - Marking/13-02 - Standard marking feasibility/13-02-01 - Standard marking feasibility - Montb...

Open

7059

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

7060

10.0

AI

No

add date

No evidence of an ISO 9001 quality-assurance system or certification by a competent EEA body is provided for the material manufacturer or Montbard plant. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

7061

10.1

AI

No

add date

No evidence provided that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body with specific assessment for materials as required by the specification. Source: 14-03 - Certification Montbard plant.doc

Open

7062

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV25.7N up to WT = 31.75 mm (inquiry WT is 18.26 mm), and the EN 10204 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number. Source: DMV_STANDARD...

Open

7063

10.2

AI

No

add date

No provided document confirms that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205. There is no explicit evidence of compliance with the transmission and traceability requirement for the Montbard plant ...

Open

7064

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control for mill inspection. Source: 14-03 - Certification Montbard plant.doc

Open

7065

10.2

AI

No

add date

No provided document contains the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or test results. General st...

Open

7066

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured and tested in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with all relevant chemical, mechanical, corrosion, and qualification requirements met, including M-650 qualification up to the req...

Open

7067

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782, which is explicitly required. No confirmation of QTR/MPCR availability for review is provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7068

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N with qualified manufacturing processes, fulfilling the requirement for manufacturer and process qualification per NORSOK M-650 or ISO 17782 and NORSOK M-630 MDS D51 rev. 6. Source: DMV_ST...

Open

7069

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7070

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and DMV material composition conforms with supplier certification and heat analysis per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02...

Open

7071

4.4.2

AI

No

add date

The available specifications allow isolated intermetallic precipitates below 10μm, but do not confirm a zero-tolerance policy for intermetallic phases/precipitates when CVN testing cannot be completed, as required by the client specification. Source:...

Open

7072

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

7073

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

7074

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

7075

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions. For the ordered pipe dime...

Open

7076

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

7077

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

7078

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness required by the standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testin...

Open

7079

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements, including Charpy V-notch testing at -46°C with specified minimum absorbed energy values and sub-size specimen reduction factors. The specified pipe dimensions allow for requi...

Open

7080

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

7081

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH is specified for detecting ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

7082

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

7083

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STANDA...

Open

7084

4.4.2

AI

No

add date

Micrographs at a minimum magnification of 400x are included, reported at actual magnification with a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

7085

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK/0...

Open

7086

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7087

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

7088

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Acceptance criteria: structure must be basically free from intermetallic precipitates (isolated precipit...

Open

7089

4.4.3

AI

No

add date

Ferrite content of 35% to 60% is required and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7090

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced; compliance cannot be confirmed. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

7091

4.5

AI

No

add date

All acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 are fulfilled for DMV 25.7N, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

7092

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

7093

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712 or equivalent standards. Requirement not fulfilled based on available...

Open

7094

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available after all processing steps, with calibration notches per ASTM E213 Figure 3 within specified dimensions. Pipe size is within machine capability. Source: DMV_S...

Open

7095

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/650 are not fully addressed. Available testing methods (hydrostatic, ultrasonic, eddy current) for the specified OD are either not feasible or only available at extra cost, and feasibilit...

Open

7096

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor that this NDE acceptance criterion is applied as standard for the requested pro...

Open

7097

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790) unless otherwise specified, and no override is indicated in the customer specification or context. Source: DMV_STANDARD_BOOK/07-01 - General informatio...

Open

7098

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7099

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

7100

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for a quality-assurance system certified within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

7101

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body established within the EEA, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-...

Open

7102

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

7103

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to products, fulfilling the requirement for documentation to be transmitted to TechnipFMC and traceable as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

7104

10.2

AI

No

add date

EN 10204 Type 3.1 material certificate will be issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control for mill inspection, and referencing compliance with the relevant standards and manufacturing summa...

Open

7105

10.2

AI

No

add date

Most required documentation and certification items (NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, metallurgical and NDT results) are stated as included in the EN ...

Open

7106

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification digest and the engineering data table listing 'A790 NORSOK' under customer specifications. Manufacturing is M-65...

Open

7107

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence provided for QTR/MPCR availability for review or full compliance with both standards and essential variables/limitations. Source: DMV_STANDARD_BOOK/02-0...

Open

7108

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

7109

3.1

AI

No

add date

AOD or equivalent refining is used 100% for DMV 25.7N, and chemical composition complies with Table 2 requirements of ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7110

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. The chemical composition table in the requirement matches the standard for S32760, and compliance is confirme...

Open

7111

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

7112

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

7113

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

7114

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at the req...

Open

7115

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7116

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 as required for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

7117

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

7118

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

7119

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C (transverse: avg 145 J, single 135 J; longitudinal: avg 165 J, single 150 J) for thickness 136 mm, and the requested pipe dimensions allow for required testing ...

Open

7120

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with 20-40% NaOH or KOH solution after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

7121

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is specified as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NO...

Open

7122

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

7123

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are reported with representative micrographs showing the presence and location of intermetallic phases. S...

Open

7124

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

7125

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_ST...

Open

7126

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement does not permit any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully fulfilled. S...

Open

7127

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

7128

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance is based on impact a...

Open

7129

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

7130

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

7131

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

7132

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

7133

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

7134

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

7135

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. Standard NDE is not available for the requested OD at Montbard without extra cost, an...

Open

7136

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair; standard NDE method (Eddy current) is not feasible for OD 219.1 mm at Montbard, and alternative NDE methods incur extra...

Open

7137

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the specified pipe, with no overriding requirements from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - To...

Open

7138

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7139

8.0

AI

No

add date

Marking is performed according to ASTM A790, requiring full traceability to melt and heat treatment lot, with mandatory marking of heat number and DMV lot number ensuring compliance. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

7140

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

7141

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

7142

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for UNS S32760/DMV25.7N up to the required wall thickness, fulfilling the qualification documentation requirement for the spe...

Open

7143

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with full traceability to the delivered products, fulfilling SIR205 documentation requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

7144

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

7145

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

7146

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or results of required metallurgical and non-des...

Open

7147

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

7148

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 or availability of QTR/MPCR documentation; only M-650 accreditation is confirmed, not ISO 17782 as required. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STA...

Open

7149

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

7150

3.1

AI

No

add date

AOD or equivalent steel refining is standard and required for 100% of production, and DMV 25.7N complies with the specified chemical composition per Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7151

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements. Heat analysis is performed per heat as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 ...

Open

7152

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

7153

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

7154

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, directly referencing the required table for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - De...

Open

7155

4.1

AI

No

add date

Tensile, hardness, CVN (Charpy V-Notch), corrosion, and microstructure tests are performed on prolongation samples from seamless pipes as required, with tensile and CVN tests in the transverse direction (longitudinal if not feasible), and all specifi...

Open

7156

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

7157

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

7158

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

7159

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C, with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal. The specified pipe dimensions allow...

Open

7160

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

7161

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

7162

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

7163

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

7164

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

7165

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

7166

4.4.2

AI

No

add date

The referenced documents do not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed; isolated precipitates are allowed under certain conditions, which does not meet the stricter client requirement of zero tolera...

Open

7167

4.4.3

AI

No

add date

Ferrite content is determined per ASTM E562 or by image analysis according to ASTM E1245, performed in accordance with ISO 17781, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

7168

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Structure must be basically free from intermetallic precipitates; isolated precipitates allowed if not d...

Open

7169

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

7170

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

7171

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, as well as manufacturing, heat treatment, and qualification requirements. S...

Open

7172

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², which DMV 25.7N complies with. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

7173

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source: DM...

Open

7174

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is confirmed for the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12...

Open

7175

5.2

AI

No

add date

NDE per ASTM A790 is partially addressed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are fulfilled. For the requested OD (219.1 mm), standard NDE (eddy current, ultrasonic, hy...

Open

7176

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor confirms NDE will be performed for the requested OD. Source: 02-03-01 - Digest ASTM A 790.docx, ...

Open

7177

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) as required, with no overriding specifications from TechnipFMC indicated in the inquiry or context. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_B...

Open

7178

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7179

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

7180

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

7181

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

7182

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body established within the EEA, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

7183

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number as required, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

7184

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

7185

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference). ...

Open

7186

10.2

AI

No

add date

No provided documentation confirms inclusion of all required items: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis (ladle), solution annealing details, and results of all req...

Open

7187

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all standard, supplementary, and testing requirements, and are M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02-03-0...

Open

7188

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782; no confirmation of QTR/MPCR availability for review. Requirement for qualification to both NORSOK M-650/ISO 17782 and documentation availability is not fulfilled. Source: DMV_...

Open

7189

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PRE ≥ 40, matching the requirements of ASTM A790 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat as required. Source: 02-03-...

Open

7190

3.2

AI

No

add date

Heat treatment is solution annealing followed by accelerated cooling (water quenching) per ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650/ISO 17782, and standard practice ensures proper pipe arrangement during heat treat...

Open

7191

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

7192

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for sampling requirements, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-0...

Open

7193

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure, is performed as specified. For the ordered pipe dimensions, transverse CVN sp...

Open

7194

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

7195

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

7196

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

7197

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements (Charpy V-notch at -46°C: transverse 45J/35J, longitudinal 65J/50J, sub-size reduction factors). The specified pipe dimensions allow for both longitudinal and transverse impact...

Open

7198

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

7199

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is required as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NO...

Open

7200

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

7201

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are reported with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

7202

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

7203

8.0

AI

No

add date

Marking includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAND...

Open

7204

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

7205

4.4.2

AI

No

add date

The available specifications allow isolated intermetallic precipitates below 10 µm, but do not prohibit all intermetallic phases and/or precipitates if CVN testing cannot be completed, as required by the client specification. The stricter client requ...

Open

7206

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

7207

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and DMV 25.7N complies, matching NORSO...

Open

7208

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

7209

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

7210

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive, micrographic, and qualification requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

7211

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

7212

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

7213

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

7214

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed. Provided documentation only covers ASTM A790/A999 NDE, not the specific NORSOK requirements. For the requested OD (219.1 mm), eddy current testing is...

Open

7215

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor is this NDE acceptance criterion stated as standard or feasible for the requested dimensio...

Open

7216

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A ...

Open

7217

7.0

AI

No

add date

ASTM A790 (6.1.3) and NORSOK MDS D51 (§13) both require finished pipes to be pickled or bright annealed, fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7218

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7219

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

7220

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

7221

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number as required, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

7222

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with full traceability to the delivered products, fulfilling the documentation and traceability requirement per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

7223

10.2

AI

No

add date

Certification is provided to EN 10204 Type 3.1, including all information required by ASTM A790 and NORSOK M-630. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certification Montbard plant.doc

Open

7224

10.2

AI

No

add date

Most documentation and certification requirements are addressed, but the specific steel producer of the starting material is not provided (only country of origin is given), and actual solution annealing parameters and test results are not included. T...

Open

7225

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/...

Open

7226

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not accredited to ISO 17782, as required. No evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.do...

Open

7227

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 (or ISO 17782), fulfilling the requirement for manufacturer and process qualification and compliance wi...

Open

7228

3.1

AI

No

add date

AOD or equivalent refining is used 100% for DMV 25.7N, and chemical composition complies with Table 2 of ASTM A790 and NORSOK MDS D51 Rev 6 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7229

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7230

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

7231

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with frequency '1/lot' and lot defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

7232

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

7233

4.1

AI

No

add date

Test sampling requirements for seamless pipes per NORSOK MDS D51/ASTM A790—including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and dire...

Open

7234

4.2

AI

No

add date

Tensile testing is performed at room temperature in accordance with ASTM A370 or ISO 6892-1, and the material meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

7235

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW, fulfilling all specified mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

7236

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and meets the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impa...

Open

7237

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energy values for transverse and longitudinal directions, and the specified pipe dimensions allow for required testing orientation and specimen...

Open

7238

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with 20-40% NaOH or KOH solution after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

7239

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is explicitly required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_...

Open

7240

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

7241

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases. Source: DMV_STANDARD_BOOK/02...

Open

7242

4.4.2

AI

No

add date

Micrographs at a minimum magnification of 400x are taken at or near mid-wall thickness, with actual magnification and scale bar, if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

7243

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

7244

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STAN...

Open

7245

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

7246

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching methods, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and...

Open

7247

4.5

AI

No

add date

Applicable standards are referenced but there is no explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 being performed or reported. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard p...

Open

7248

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 are fully met, including compliance for destructive and micrographic tests, solution annealing, ferrite range, absence of intermetallics, and required certifications and qualif...

Open

7249

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

7250

5.1

AI

No

add date

No evidence provided regarding qualification or certification of NDE personnel to ISO 9712 level II or III, nor definition of their roles and responsibilities as per ISO 9712 or equivalent. Requirement not fulfilled based on available information. So...

Open

7251

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

7252

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/ISO 17782 are not fully addressed. Only standard hydrostatic or NDE (EC/UT) per ASTM A999 is confirmed, but NORSOK-specific NDE requirements are not evidenced. For OD 219.1 mm, eddy curre...

Open

7253

5.2

AI

No

add date

None of the referenced documents explicitly state that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, and standard NDE methods are not feasible for the requested OD at Montbard, s...

Open

7254

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specifications from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A...

Open

7255

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7256

8.0

AI

No

add date

Marking is per ASTM A790 §14 and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-...

Open

7257

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

7258

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

7259

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

7260

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number as required, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

7261

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with required traceability and documentation for TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 -...

Open

7262

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - ...

Open

7263

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

7264

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, ladle chemical analysis, solution annealing parameters, or complete metallurgical and no...

Open

7265

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all relevant chemical, mechanical, manufacturing, and testing requirements. M-650 qualification is confirmed for the specified product and wall thi...

Open

7266

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N, with manufacturing processes qualified per NORSOK M-650 (or ISO 17782), and compliance with NORSOK M-630 MDS D51 Rev. 6 is referenced. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

7267

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7268

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed by heat analysis with supplier certification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Dige...

Open

7269

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

7270

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

7271

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, directly referencing the required table for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - De...

Open

7272

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure tests at specified locations per NORSOK MDS D51/ASTM A790. For the sp...

Open

7273

4.2

AI

No

add date

Tensile testing is performed at room temperature per NORSOK MDS D51, which refers to ASTM A790 and allows ASTM A370 or ISO 6892-1 methods. Required tensile and maximum hardness properties are met as per Table 4. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

7274

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

7275

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

7276

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C, with minimum absorbed energy values for transverse and longitudinal directions, and the specified pipe dimensions allow for required testing directions and specimen ...

Open

7277

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

7278

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

7279

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

7280

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

7281

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included with presence and location of intermetallic phases noted and recorded. Source: DMV_STANDA...

Open

7282

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

7283

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

7284

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

7285

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

7286

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

7287

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in accordance with ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

7288

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

7289

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, as well as manufacturing, heat treatment, and qualification requirements. Source: DMV_STAN...

Open

7290

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

7291

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

7292

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, which are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-0...

Open

7293

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7294

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis is performed per heat and matches the required limits for all elements listed in the requ...

Open

7295

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/NORSOK M-650 are not fully addressed. Hydrostatic or NDE (EC or UT) testing per ASTM A999 is confirmed, but NORSOK-specific NDE requirements are not evidenced. For the specified OD, eddy ...

Open

7296

5.2

AI

No

add date

None of the provided documents explicitly confirm that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, as specified in the requirement. NDE methods and general compliance are re...

Open

7297

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specifications stated by the customer or TechnipFMC. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A ...

Open

7298

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7299

8.0

AI

No

add date

Marking per ASTM A790 §16.1 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.do...

Open

7300

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

7301

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

7302

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

7303

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

7304

10.2

AI

No

add date

EN 10204 Type 3.1 certificate will be issued and will include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary ...

Open

7305

10.2

AI

No

add date

Some documents state that most required information (NORSOK M-650/ISO 17782 identification, QTR/MPCR number, melting practice, heat number, chemical analysis, solution annealing details, and test results) is included in the EN 10204 3.1 certificate, ...

Open

7306

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all relevant chemical, mechanical, manufacturing, and testing requirements, and are M-650 qualified up to the required wall thickness. Source: DMV_...

Open

7307

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability. Requirement for qualification to both NORSOK M-650/ISO 17782 and documentation availability is not ...

Open

7308

3.2

AI

No

add date

Manufacturing process is qualified to NORSOK M-650, heat treatment is solution annealed followed by accelerated cooling per ASTM A790, and furnace compliance with NORSOK M-650/ISO 17782 is confirmed. Free circulation of heating/cooling media is ensur...

Open

7309

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

7310

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

7311

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations, all per ASTM A790 and NORSOK requirement...

Open

7312

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

7313

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

7314

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Im...

Open

7315

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements, including Charpy V-notch testing at -46°C with minimum absorbed energy values (transverse: 45 J average, 35 J single; longitudinal: 65 J average, 50 J single if transverse no...

Open

7316

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH solution after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

7317

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

7318

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

7319

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

7320

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

7321

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK/0...

Open

7322

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fulfilled. Source: DMV_STAN...

Open

7323

4.4.3

AI

No

add date

Ferrite content is checked per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing methods and standard compliance for ferrite determination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

7324

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

7325

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7326

4.5

AI

No

add date

No explicit confirmation that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or included in the referenced documents or standards. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant....

Open

7327

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, chemical composition, ferrite content, corrosion, impact, PRE, tensile, and microstructure requirements. Sour...

Open

7328

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

7329

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destruct...

Open

7330

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is confirmed for the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12...

Open

7331

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially addressed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are fulfilled. For the requested OD, standard NDE methods (EC, UT, hy...

Open

7332

5.2

AI

No

add date

None of the reviewed documents confirm that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair; the specific NDE acceptance criterion is not addressed or confirmed as standard pract...

Open

7333

6.0

AI

No

add date

Dimensional tolerances are confirmed as per the applicable ASTM standard (ASTM A790/A999) for the requested pipe, with no deviations or overrides specified by the customer or TechnipFMC. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - Gen...

Open

7334

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7335

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

7336

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

7337

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

7338

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

7339

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness for the specified size and product form. Source: DMV_STANDARD_BO...

Open

7340

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

7341

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with issuance and validation by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

7342

10.2

AI

No

add date

Required documentation elements such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, heat number, full chemical analysis, specific solution annealing parameters, and actual metallurgical and non-destructive test results a...

Open

7343

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with explicit recognition of both standards and fulfillment of all relevant mechanical, chemic...

Open

7344

1.0

AI

No

add date

No evidence of supplier qualification to NORSOK M-650/ISO 17782 for the exact product supplied or availability of QTR/MPCR documentation. MST-Tubes is NORSOK M-650 accredited for DMV 25.7N but not ISO 17782 accredited, which is required by the specif...

Open

7345

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm for hot finished, 10.925 mm for cold finished), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 require...

Open

7346

3.1

AI

No

add date

AOD or equivalent is used for 100% of production and DMV 25.7N complies with the chemical composition requirements in Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

7347

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the inquiry for DMV 25.7N with WT = 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

7348

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed per ASTM A790, with manufacturing process and furnaces qualified according to NORSOK M-650 or ISO 17782, ensuring compliance with requirements for free circulation of he...

Open

7349

4.1

AI

No

add date

No provided document confirms that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790. Testing frequency, lot definition, and full complia...

Open

7350

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

7351

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no evidence of CVN impact testing, required test directions, or specified sampling locations (outer surface, 1/2 thickness, full thickness) as required by the specification table for test sampl...

Open

7352

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature, meeting or exceeding the required mechanical properties, and is conducted in accordance with NORSOK MDS D51, which references ASTM A790 and thus ASTM A370 for mechanical testing. Source: DMV_S...

Open

7353

4.2

AI

No

add date

None of the provided documents confirm that the required mechanical properties (tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, hardness max 310/300 HBW) for DMV 25.7N are met. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM ...

Open

7354

4.3

AI

No

add date

No evidence that Charpy V-notch testing is performed or meets ASTM A370, ASTM A1058, ISO 148-1, or Table 5 requirements for the specified product or order position. Feasibility rules are mentioned, but compliance and execution are not confirmed. Sour...

Open

7355

4.3

AI

No

add date

Impact testing at -46°C with specified absorbed energy values is feasible and can be fulfilled for pipe with 18.26mm wall thickness, as transverse specimens are possible for NPS 8 at this thickness. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test fo...

Open

7356

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination per ISO 17781 or the specified etchant solution for 25 Cr Duplex stainless steels. Grain size examination procedures for austenitic materials are not applicable to duplex...

Open

7357

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination is provided or confirmed for ferrite balance and intermetallic phase assessment in duplex/super-duplex steels. Sou...

Open

7358

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic phases; isolated phases are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

7359

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided or addressed in the relevant documentation or comments. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/1...

Open

7360

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at 400x minimum magnification with a scale bar when intermetallic phases are not detected. Partial mention of 400x magnification and photos, but not a...

Open

7361

4.4.2

AI

No

add date

No relevant documentation addresses the reporting of centerline intermetallic stringers or acceptance criteria based on CVN and corrosion test results if such stringers are present. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I...

Open

7362

4.4.2

AI

No

add date

NORSOK MDS D41 Rev 06 and NORSOK MDS D51 Rev 06 allow isolated intermetallic precipitates below 10µm and do not fully prohibit all intermetallic phases/precipitates when CVN testing cannot be completed, so the requirement is not fully fulfilled. ASTM...

Open

7363

4.4.3

AI

No

add date

No evidence of ferrite content measurement by ASTM E 562, ASTM E 1245, or ISO 17781 is provided; only grain size measurement is discussed. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Micrographic Examination/...

Open

7364

10.1

AI

No

add date

No evidence that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body is provided. Source: 14-03 - Certification Montbard plant.doc

Open

7365

4.4.3

AI

No

add date

No acceptance criteria for micrographic examination are specified or referenced for DMV 25.7N in the provided documents; only procedures and general information are given without required values or ranges for acceptance. Source: DMV_STANDARD_BOOK/02-...

Open

7366

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7367

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

7368

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are provided; referenced documents discuss related properties but do not state explicit acceptance values or criteria for validation. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790....

Open

7369

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 G48 Method A at 25°C for 24 hours is required, with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the client's requirements. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

7370

5.1

AI

No

add date

No evidence provided regarding qualification or certification of NDE personnel to ISO 9712 level II or III, or their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDARD_BOOK/...

Open

7371

5.2

AI

No

add date

No explicit confirmation of 100% ultrasonic testing per ASTM E213 or ISO 10893-10 after all processing steps, nor confirmation of calibration notch requirements or coverage as specified in the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testi...

Open

7372

5.2

AI

No

add date

100% qualitative anti-mixing PMI check is performed on standard production at Montbard using appropriate instruments, fulfilling the NDE requirement for positive material identification. Quantitative PMI procedure and frequency are also defined if re...

Open

7373

5.2

AI

No

add date

No provided document confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair for the specified product and dimension; NDE feasibility and acceptance criteria are not explicitly addressed or co...

Open

7374

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for the specified product are confirmed as per the applicable ASTM standards (including ASTM A790/A999) with no deviations indicated, fulfilling the requirement that tolerances follow ASTM unless otherwi...

Open

7375

7.0

AI

No

add date

Both ASTM A790 and NORSOK MDS S01 require finished pipes to be pickled or bright annealed, directly matching the requirement for white pickled or bright annealed pipes. Source: ASTM A790 digest, NORSOK MDS S01 Rev 05.

Open

7376

9.0

AI

No

add date

Weld repairs are explicitly stated as not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

7377

10.0

AI

No

add date

No evidence of ISO 9001 or equivalent certification by a competent EEA body or specific assessment for materials is provided. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Certification Montbard plant.doc

Open

7378

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

7379

10.2

AI

No

add date

No provided document confirms that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC as specified. No explicit evidence of SIR205 or equivalent documentation being provided and traceable is present for t...

Open

7380

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control, with inclusion of information required by ASTM A790 and NORSOK M-630 implied by referenced standards. Source: 14-03 - Certification Montbard plant.doc

Open

7381

10.2

AI

No

add date

No provided document contains the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or results of metallurgical...

Open

7382

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, meeting all chemical, mechanical, manufacturing, and testing requirements for 25 Cr Duplex stainless steel seamless pipes as specified. Sourc...

Open

7383

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR documentation availability as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7384

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

7385

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7386

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7387

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnace qualification per NORSOK M-650/ISO 17782. Free circulation of heating/cooling media is ensured by compliance with these standards. Sourc...

Open

7388

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

7389

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the specified frequency, fulfilling the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detai...

Open

7390

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per ASTM A790 and NORSOK r...

Open

7391

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-0...

Open

7392

4.5

AI

No

add date

Requirement for no pitting at 20X magnification and weight loss less than 1.0 g/m² is met by compliance with ISO 17781: G48 Method A, as specified for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

7393

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW, fulfilling Table 4 mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

7394

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness requirements for testing. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - I...

Open

7395

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal, and the specified pipe dimensions allow for required testing directions a...

Open

7396

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

7397

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution for detecting ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

7398

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

7399

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

7400

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

7401

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

7402

4.4.2

AI

No

add date

The standard allows isolated intermetallic precipitates below 10µm, which does not fully meet the requirement that intermetallic phases and/or precipitates are not permitted if CVN testing cannot be completed due to geometry or size. No evidence was ...

Open

7403

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

7404

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impa...

Open

7405

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

7406

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

7407

4.5

AI

No

add date

DMV 25.7N meets all metallurgical property requirements and acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, with mill M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

7408

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destruct...

Open

7409

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed on the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - U...

Open

7410

5.2

AI

No

add date

NDE per ASTM A790 is detailed, but compliance with additional NDE requirements from NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 is not confirmed. For the specified OD, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are onl...

Open

7411

5.2

AI

No

add date

The specific NDE acceptance criterion that any indication greater than that produced by the calibration notch represents a defect, requiring rejection or repair, is not explicitly confirmed in the referenced documents. Additionally, Eddy current test...

Open

7412

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the requested pipe, with no deviations or special tolerances specified by the customer or TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STAN...

Open

7413

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7414

8.0

AI

No

add date

Marking per ASTM A790 includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Marking methods (indelible ink, vibro-etching) are standard and applied as specified. Source: DMV_STANDARD_BOOK/02-04-03 - Diges...

Open

7415

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

7416

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

7417

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

7418

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV25.7N, and the EN 10204 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number for the specified size and product form. Source: DMV_ST...

Open

7419

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to the delivered products, fulfilling the documentation and traceability requirements of SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

7420

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

7421

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C, with minimum transverse (average 45 J, single 35 J) and longitudinal (average 65 J, single 50 J) absorbed energy values, and the specified pipe dimensions allow for ...

Open

7422

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all metallurgical and no...

Open

7423

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, meeting all specified chemical, mechanical, manufacturing, and testing requirements for 25 Cr Duplex stainless steel seamless pipes. Source: DMV_STANDARD_BOO...

Open

7424

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N but not to ISO 17782; no evidence provided for full qualification to NORSOK M-650/ISO 17782 or availability of QTR/MPCR as required by the specification. Source: DMV_STANDARD_BOOK/02-0...

Open

7425

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

7426

3.1

AI

No

add date

AOD or equivalent refining is used for 100% of production, and DMV 25.7N complies with the required chemical composition per Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7427

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790 as required, with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 7...

Open

7428

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

7429

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

7430

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

7431

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled per NORSOK MDS D51/ASTM A790. Fo...

Open

7432

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4 as specified in NORSOK MDS D51. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

7433

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

7434

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness required for standard transverse specimens. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - D...

Open

7435

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with specified etchants after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

7436

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

7437

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

7438

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

7439

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

7440

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

7441

4.4.2

AI

No

add date

The referenced specifications allow isolated intermetallic precipitates below 10 µm, but do not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed, as required. Zero-tolerance is not confirmed for this case. So...

Open

7442

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

7443

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), in compliance with NORSOK MDS D51/ASTM...

Open

7444

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

7445

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

7446

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including chemical composition, PRE, tensile, impact, corrosion, microstructure, and ferrite content requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

7447

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

7448

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

7449

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

7450

5.2

AI

No

add date

NDE per ASTM A790 and NORSOK M-630 MDS D51 is required, but available evidence only confirms hydrostatic or NDE per ASTM A999, with no explicit confirmation of NORSOK-specific NDE methods or acceptance criteria. Eddy current testing is not feasible f...

Open

7451

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair, and no evidence that NDE methods meeting this criterion are standardly available for the specified size at Montbard. So...

Open

7452

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the requested pipe, with no deviations specified by the customer or TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - T...

Open

7453

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7454

8.0

AI

No

add date

Marking per ASTM A790 §16 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

7455

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

7456

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

7457

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system certified within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

7458

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

7459

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability information, fulfilling the requirement for documentation traceable to delivered products and transmission to TechnipFMC. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

7460

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications and documentation. Source: DMV_STANDARD_BOOK/02-04-03 - Digest ...

Open

7461

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution annealing parameters, and ...

Open

7462

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by both the customer specification listing and the digest, including all mechanical, chemical, and testing requirements. Manufactur...

Open

7463

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of full qualification to both standards or availability of QTR/MPCR as required by the specification. Source: DMV_STANDARD_BOOK/0...

Open

7464

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

7465

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 requirements for DMV 25.7N seamless pipe. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7466

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat, confirming conformity to the required ...

Open

7467

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

7468

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

7469

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

7470

4.1

AI

No

add date

Test sampling for seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per ASTM A790/NORSOK. For the ordere...

Open

7471

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-0...

Open

7472

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

7473

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement for both longitudinal and transverse directions for wall thickness >6mm as required by the standards. Source: DMV...

Open

7474

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energy values for both transverse and longitudinal directions, and the specified pipe dimensions allow for required testing directions and spec...

Open

7475

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

7476

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided or addressed in the relevant documentation or comments. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/1...

Open

7477

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

7478

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

7479

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and the presence and location of intermetallic phases are noted and recorded with micrographs. Source: DMV_STANDARD_BO...

Open

7480

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report at actual magnification and with a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/...

Open

7481

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

7482

4.4.2

AI

No

add date

No document fully prohibits intermetallic phases and/or precipitates when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10µm, which does not meet the stricter client requirement. Source: DMV_STANDARD_BOOK/0...

Open

7483

4.4.3

AI

No

add date

Ferrite content is checked as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite determination methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

7484

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

7485

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

7486

4.5

AI

No

add date

Corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is not explicitly referenced or confirmed in the provided documentation or listed standards. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

7487

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified per NORSOK M-650/ISO 17782. Source: Digest NORSOK MDS D51 Rev 06.docx

Open

7488

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

7489

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

7490

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/1...

Open

7491

1.0

AI

No

add date

No evidence of supplier qualification to NORSOK M-650/ISO 17782 for the exact product supplied or availability of QTR/MPCR documentation as required by the specification. MST-Tubes is NORSOK M-650 accredited for DMV 25.7N but not ISO 17782 accredited...

Open

7492

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. Only ASTM A790/A999 NDE (hydrostatic, EC, or UT) is confirmed, but not full NORSOK-specific requirements. For OD 219.1 mm, eddy current is...

Open

7493

5.2

AI

No

add date

No explicit confirmation that NDE indications greater than the calibration notch are treated as defects requiring rejection or repair; referenced standards and plant feasibility documents do not specify this acceptance criterion for the requested pip...

Open

7494

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no deviations or special tolerances specified for TechnipFMC. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances...

Open

7495

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7496

8.0

AI

No

add date

Marking per ASTM A790 and plant marking methods include heat number and lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

7497

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

7498

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

7499

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

7500

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling supplier qualification documentation requirem...

Open

7501

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to the delivered products, fulfilling the requirement for documentation traceable to the products as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

7502

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

7503

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution annealing temperature/holding time/quench medium, or re...

Open

7504

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, including mechanical, chemical, and testing requirements for 25 Cr Duplex stainless steel. Source: DMV_STAN...

Open

7505

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm for hot finished, 10.925 mm for cold finished), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 require...

Open

7506

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N meets the chemical composition requirements of Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

7507

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the inquiry's WT of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest ...

Open

7508

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling (including water quenching) as per ASTM A790, with manufacturing process qualified according to NORSOK M-650 or ISO 17782. Free circulation of heating and cooling media is ensured by complia...

Open

7509

4.1

AI

No

add date

There is no explicit evidence that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790. Testing frequency, lot definition, and full complia...

Open

7510

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

7511

4.1

AI

No

add date

Tensile, hardness, CVN, and corrosion/microstructure tests on prolongation samples from seamless pipes are covered, with tensile test direction per ASTM A790 and all thicknesses included. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

7512

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature with criteria matching or exceeding Table 4 requirements, and hardness testing is performed as required. Compliance with NORSOK MDS D51 and mechanical property requirements is demonstrated. Sou...

Open

7513

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) for DMV 25.7N are not confirmed; referenced documents do not provide the required minimums or cover the correct grade. Source: DMV_STANDARD_BOOK/02-03-01 - Digest AST...

Open

7514

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, meeting the minimum wall thickness requirements for both longitudinal and transverse specimens. Source: DMV_STANDARD_BOOK/12 - Special Testi...

Open

7515

4.3

AI

No

add date

Pipe dimensions allow for transverse Charpy V-notch specimens; impact property requirements at -46°C are feasible and can be fulfilled for this product. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact test...

Open

7516

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination of 25 Cr Duplex stainless steels to ISO 17781 or the specified etching procedures for duplex grades. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive te...

Open

7517

4.4.1

AI

No

add date

No information confirming the use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination or to reveal ferrite balance and intermetallic phases is provided. Source: DMV_STANDARD_BOOK/12 - S...

Open

7518

4.4.2

AI

No

add date

The micrographic examination section requires the microstructure to be basically free from intermetallic precipitates, but allows isolated precipitates if not homogeneously distributed and each is below 10 μm, matching the client's requirement exactl...

Open

7519

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at 400x minimum magnification with a scale bar and actual magnification when intermetallic phases are not detected. Partial mention of 400x and photos...

Open

7520

4.4.2

AI

No

add date

No relevant documents address the reporting of centerline intermetallic stringers or acceptance criteria based on CVN and corrosion test results in such cases. Requirement not fulfilled. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in ...

Open

7521

4.4.2

AI

No

add date

Referenced specifications allow isolated intermetallic precipitates below 10μm if not distributed over the whole specimen, but do not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed, as required by the clien...

Open

7522

4.4.3

AI

No

add date

No information is provided confirming ferrite content determination per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781; only grain size measurement is discussed, not ferrite content measurement methods or results. Source: DMV_STANDARD_BOOK/12...

Open

7523

4.4.3

AI

No

add date

No provided document specifies acceptance criteria or results for micrographic examination as required in section 4.4 of the client specification for DMV 25.7N at Montbard. Relevant documents only address other properties or do not mention micrograph...

Open

7524

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7525

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) performed in accordance with ISO 17781 is provided in the available information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

7526

4.5

AI

No

add date

No explicit acceptance criteria for metallurgical properties are specified in the provided documents, making validation impossible. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS S01 Rev 05...

Open

7527

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² are specified, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

7528

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

7529

5.2

AI

No

add date

No explicit confirmation of 100% ultrasonic testing per ASTM E213 or ISO 10893-10, calibration notch criteria, or testing after all processing steps is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 ...

Open

7530

5.2

AI

No

add date

100% qualitative anti-mixing PMI check is performed on standard production at Montbard using appropriate instruments, fulfilling the general NDE requirement for PMI. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02...

Open

7531

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor is the acceptance criterion or policy explicitly addressed for the specified dimensions an...

Open

7532

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

7533

3.1

AI

No

add date

AOD or equivalent refining is standard for production and required for 100% of material; chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D...

Open

7534

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

7535

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for both hot and cold finished products are confirmed as compliant with the applicable ASTM standards (including ASTM A790/A999) for the specified dimensions, with no overriding TechnipFMC requirements i...

Open

7536

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed per ASTM A790 and white pickled or bright annealed per NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: Digest ASTM A 790.docx, ...

Open

7537

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

7538

10.0

AI

No

add date

No evidence is provided that the material manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body with a specific assessment for materials. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-01 - General info...

Open

7539

10.1

AI

No

add date

No evidence provided that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-03...

Open

7540

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, demonstrating qualification for the size and product for...

Open

7541

10.2

AI

No

add date

No provided document confirms that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205. There is no explicit evidence of compliance with the documentation transmission and traceability requirement. Source: ...

Open

7542

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control for mill inspection as required. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-...

Open

7543

10.2

AI

No

add date

None of the provided documents include the required documentation or certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing paramete...

Open

7544

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all mechanical, chemical, and testing requirements, and are M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOO...

Open

7545

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51...

Open

7546

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to 31.75 mm WT), matching the requested grade and wall thickness (18.26 mm), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev...

Open

7547

3.1

AI

No

add date

Chemical composition for S32760 matches Table 2 requirements and is confirmed to conform per heat analysis for DMV material. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ...

Open

7548

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured ...

Open

7549

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

7550

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

7551

4.1

AI

No

add date

Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, are fulfilled for DMV 25.7N. For...

Open

7552

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

7553

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

7554

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

7555

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for required transverse testing. Source: DMV_STANDARD...

Open

7556

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with etching by 20-40% NaOH or KOH after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Di...

Open

7557

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03...

Open

7558

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

7559

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are reported with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

7560

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

7561

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NO...

Open

7562

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

7563

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

7564

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impa...

Open

7565

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7566

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

7567

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORS...

Open

7568

4.5

AI

No

add date

Requirement for no pitting at 20X magnification and weight loss less than 1.0 g/m² is met per corrosion test section (§11) of NORSOK MDS D51 Rev 06, with DMV 25.7N compliant to these criteria under ISO 17781 G48 Method A at 50°C for 24 hours. Source:...

Open

7569

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

7570

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

7571

5.2

AI

No

add date

NDE per ASTM A790 is partially addressed with hydrostatic or NDE (EC or UT) testing per ASTM A999, but there is no explicit confirmation of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE acceptance criteria. For the...

Open

7572

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair; NDE acceptance criteria and feasibility for the specified dimension are not demonstrated for Montbard plant. Source: 02...

Open

7573

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specifications from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a A...

Open

7574

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7575

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures ensures mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

7576

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

7577

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

7578

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified s...

Open

7579

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

7580

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications and plant certification procedures. Source: DMV_STANDARD_BOOK/02-...

Open

7581

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or test results for the specific order. Only general practices or partial information (e....

Open

7582

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all supplementary requirements and M-650 qualification, as specified in the client inquiry and supporting digests. Source: DMV_STANDARD_BOOK/02-03-...

Open

7583

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of Qualification Test Records or Manufacturer Procedure Conformity Records availability. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev ...

Open

7584

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

7585

3.1

AI

No

add date

AOD or equivalent steel refining is standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7586

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7587

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling (including water quenching) per ASTM A790; manufacturing process and furnaces are qualified to NORSOK M-650 or ISO 17782; pipes are arranged to ensure free circulation of heating and cooling...

Open

7588

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

7589

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

7590

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness loc...

Open

7591

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

7592

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

7593

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Im...

Open

7594

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements, including Charpy V-notch testing at -46°C with minimum absorbed energy values (transverse: 45 J average/35 J single, longitudinal: 65 J average/50 J single) and sub-size spec...

Open

7595

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

7596

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

7597

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

7598

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

7599

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, reported at actual magnification and including a scale bar, if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - ...

Open

7600

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

7601

4.4.2

AI

No

add date

The available documents do not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed; isolated precipitates are still allowed, which does not meet the stricter client requirement that none are permitted in this ca...

Open

7602

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

7603

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781 with specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requirement f...

Open

7604

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, as well as manufacturing, heat treatment, and qualification requirements. Source: DMV_STAN...

Open

7605

4.5

AI

No

add date

DMV 25.7N meets the corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours, with no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

7606

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor are their roles and responsibilities as defined in ISO 9712 addressed. Source: DMV_STANDARD_BOOK/12-02-01 - Non d...

Open

7607

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed on the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - U...

Open

7608

5.2

AI

No

add date

NDE per ASTM A790 and NORSOK M-630 MDS D51 is required, but available evidence only confirms hydrostatic or NDE (EC/UT) per ASTM A999, not NORSOK-specific criteria. For OD 219.1 mm, eddy current is not feasible, and ultrasonic/hydrostatic are only av...

Open

7609

5.2

AI

No

add date

No provided document explicitly states that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, nor confirms standard NDE application for the requested pipe dimension. NDE acceptance c...

Open

7610

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are confirmed to be per the applicable ASTM standard (ASTM A999), with no overriding customer specification or drawing indicated. Requirement is fulfilled as tolerances are per ASTM unless otherwise stated. S...

Open

7611

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 require finished pipes to be pickled or bright annealed, fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7612

8.0

AI

No

add date

Marking is per ASTM A790 §14 and includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

7613

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7614

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

7615

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

7616

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demonstration for th...

Open

7617

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

7618

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for 18.26mm wall thickness and 219.1mm OD pipe as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impac...

Open

7619

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference). ...

Open

7620

10.2

AI

No

add date

No provided documentation confirms the inclusion of NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, ladle chemical analysis, solution annealing parameters, or the full results of all required metallurgical and no...

Open

7621

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all referenced mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified for the required wall ...

Open

7622

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence provided for QTR/MPCR availability for review by TechnipFMC as specified in the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

7623

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

7624

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7625

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits and PREN requirements specified in Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 6 requirements for S32760. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK ...

Open

7626

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650/ISO 17782, and proper pipe placement during heat treatment is ensured. So...

Open

7627

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

7628

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

7629

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specifi...

Open

7630

4.2

AI

No

add date

Tensile and hardness testing are performed per ASTM A370, with results meeting the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produc...

Open

7631

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

7632

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C (transverse: 45 J avg/35 J single; longitudinal: 65 J avg/50 J single if transverse not possible) for thickness 6 mm, and the specified pipe dimensions allow for re...

Open

7633

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

7634

4.4.1

AI

No

add date

Etching with 20–40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

7635

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

7636

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

7637

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

7638

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

7639

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Zero-tolerance is not guaranteed by the available document...

Open

7640

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

7641

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

7642

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

7643

4.5

AI

No

add date

No explicit evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or confirmed in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

7644

4.5

AI

No

add date

DMV 25.7N complies with all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

7645

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02...

Open

7646

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

7647

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultr...

Open

7648

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782 requirements are addressed. For the requested OD and weight, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are...

Open

7649

5.2

AI

No

add date

No provided documentation explicitly states that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, nor confirms feasibility of the required NDE for the specified dimensions at Montba...

Open

7650

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790/A999) for the specified pipe size, with no overriding TechnipFMC requirements indicated in the context or documents provided. Source: DMV_STANDARD_BOOK/07-01 - Gen...

Open

7651

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7652

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

7653

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7654

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

7655

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

7656

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for UNS S32760/DMV25.7N up to the required wall thickness, fulfilling the requirement for qualification documentation for the...

Open

7657

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body and provides EN 10204 type 3.1 certificates traceable to the delivered products, fulfilling the documentation and traceability requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

7658

10.2

AI

No

add date

Certification is provided to EN 10204 Type 3.1, and the certificate includes all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference). Source: D...

Open

7659

10.2

AI

No

add date

Most documentation and certification requirements are stated as included in the EN 10204 type 3.1 certificate, except the steel producer of the starting material, for which only the country of origin is provided, not the actual producer's name. No ac...

Open

7660

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as required for 25 Cr Duplex stainless steel seamless pipes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

7661

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7662

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N (up to WT 31.75 mm) but not accredited to ISO 17782; no evidence provided for QTR/MPCR availability or full compliance with both standards as required. Source: DMV_STANDARD_BOOK/02-04-03 ...

Open

7663

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

7664

3.1

AI

No

add date

AOD or equivalent refining is required and used for 100% of production, and chemical analysis for DMV 25.7N is confirmed as compliant with the specification table. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

7665

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition requirements, including PRE ≥ 40, as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7666

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compliance...

Open

7667

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is carried out per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/...

Open

7668

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

7669

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations. The ordered pipe...

Open

7670

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

7671

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

7672

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions (18.26mm WT, 219.1mm OD) in both longitudinal and transverse directions as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - D...

Open

7673

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible). The specified pipe dimensions allow ...

Open

7674

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

7675

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

7676

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including all specified element limits and PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 R...

Open

7677

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

7678

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

7679

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

7680

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 requires reporting of intermetallic phases, with acceptance based on CVN and corrosion test results if such phases are present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STAN...

Open

7681

4.4.2

AI

No

add date

The available specifications do not fully prohibit intermetallic phases and/or precipitates when CVN testing cannot be completed; isolated precipitates are allowed under certain conditions, which does not meet the stricter client requirement of no in...

Open

7682

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

7683

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

7684

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

7685

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or confirmed in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

7686

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and complies with NORSOK and ASTM A790 qualification processes. Source: DMV...

Open

7687

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

7688

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

7689

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

7690

5.2

AI

No

add date

NDE requirements per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. Standard NDE capability for the specified OD is not available at Montbard; available methods (hydrostatic, ultrasonic, eddy current) require extr...

Open

7691

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor confirms standard NDE capability for the requested pipe size and requirement. Source: DMV_STANDA...

Open

7692

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no deviations specified by the customer. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A 376-02a A 7...

Open

7693

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7694

8.0

AI

No

add date

Marking is performed per ASTM A790 §14 and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

7695

9.0

AI

No

add date

Weld repairs are explicitly stated as not acceptable under 'Surface finish / Repairs of defects' (§13, §14) for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 -...

Open

7696

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

7697

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

7698

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness for the specified size and product form. Source: DMV_STANDARD_BOO...

Open

7699

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

7700

10.2

AI

No

add date

Certification is provided to EN 10204 Type 3.1 and includes all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control and reference to relevant standards and qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest...

Open

7701

10.2

AI

No

add date

EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MPCR number, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the spe...

Open

7702

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782, and there is no confirmation of QTR/MPCR availability for review as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

7703

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - S...

Open

7704

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and per 100 pieces, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

7705

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

7706

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

7707

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, as specified in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

7708

4.4.2

AI

No

add date

No provided document prohibits all intermetallic phases and/or precipitates when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10µm, which does not meet the stricter client requirement. Source: DMV_STANDARD...

Open

7709

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

7710

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

7711

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, including chemical, mechanical, manufacturing, and testing requirements. M-650 qualification is confirmed f...

Open

7712

3.2

AI

No

add date

Solution annealing followed by accelerated cooling is performed per ASTM A790; manufacturing and furnace qualification are per NORSOK M-650/ISO 17782; MST-Tubes is M-650 accredited for DMV 25.7N; free circulation of heating/cooling media is ensured b...

Open

7713

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required by NORSOK MDS D51 Rev 6 and ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

7714

4.4.1

AI

No

add date

Etching with 20–40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is explicitly required for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

7715

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

7716

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) performed in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

7717

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed after all mechanical processing, heat treatments, and straightening, with equipment suitable for the required dimensions. Acceptance of ASTM E213 implies comp...

Open

7718

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7719

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

7720

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

7721

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

7722

1.0

AI

No

add date

No evidence that the supplier is qualified to both NORSOK M-650 and ISO 17782 or that Qualification Test Records/Manufacturer Procedure Conformity Records are available for review. Supplier is only accredited to M-650, not ISO 17782. Source: DMV_STAN...

Open

7723

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, and the necessary tests are feasible for the specified pipe dimensions. Source: DMV_STANDAR...

Open

7724

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and meets ASTM A370 and ISO 148-1 requirements for minimum wall thickness. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-0...

Open

7725

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

7726

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10 µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully met. Source: DMV_STANDA...

Open

7727

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, with manufacturing and qualification processes compliant with NORSOK M-650/ISO 17782. Sour...

Open

7728

5.2

AI

No

add date

NDE requirements per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. For the requested OD (219.1 mm), Eddy current testing is not feasible, and hydrostatic/ultrasonic testing is only available at extra cost and req...

Open

7729

8.0

AI

No

add date

Marking per ASTM A790 and NORSOK MDS D51 includes heat number, lot number, and other traceable information using indelible ink or vibro-etching, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NO...

Open

7730

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system as specified in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 -...

Open

7731

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the specification and documentation process. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORS...

Open

7732

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive te...

Open

7733

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

7734

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 for DMV 25.7N duplex stainless steel seamless pipe as required by ASTM A790 and NORSOK M-630 MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02-03...

Open

7735

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided; compliance cannot be confirmed based on the available information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard...

Open

7736

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified according to NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

7737

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and is confirmed compliant with these requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

7738

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

7739

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, with reference notches per ASTM E213 standard practice and testing performed after all processing steps. Source: DMV_STAND...

Open

7740

5.2

AI

No

add date

NDE per ASTM A790 and NORSOK M-630 MDS D51 is required, but available documentation only confirms standard NDE per ASTM A790/ASTM A999 and does not address NORSOK-specific NDE acceptance criteria. For the requested OD (219.1 mm), standard NDE (eddy c...

Open

7741

5.2

AI

No

add date

No provided document explicitly states that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, nor confirms standard NDE application for the specified dimension at Montbard. NDE accep...

Open

7742

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no deviations or overrides by TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A 376...

Open

7743

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02...

Open

7744

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

7745

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

7746

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

7747

10.2

AI

No

add date

Certification to ISO 9001 is provided, and documentation including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number is traceable and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOO...

Open

7748

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and covering heat treatment, steel manufacturer, melting and refining practice, and M-650/ISO17782 manufactur...

Open

7749

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all metallurgical and no...

Open

7750

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by both the item table and technical digests. All relevant chemical, mechanical, manufacturing, and testing requirements are met...

Open

7751

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability. Requirement for NORSOK M-650/ISO 17782 qualification and documentation is not fully met. Source: D...

Open

7752

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

7753

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process follows M-650 (or ISO 17782) qualified procedures, fulfilling the requirement for manufacturer and process qualification and meeting N...

Open

7754

4.1

AI

No

add date

Test specimens sampling is defined and performed according to Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM...

Open

7755

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse absorbed energy (average/single) of 45 J/35 J, minimum longitudinal absorbed energy (average/single) of 65 J/50 J (if tran...

Open

7756

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

7757

4.4.3

AI

No

add date

Ferrite content is checked per ISO 17781 using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite determination per ASTM E562 or E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

7758

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, meeting the criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

7759

5.2

AI

No

add date

No provided documentation explicitly confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair per the requirement. NDE methods for the specified OD are either not feasible or only available at ...

Open

7760

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7761

10.1

AI

No

add date

Supplier MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the requirement for qualification for the specified ...

Open

7762

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02...

Open

7763

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7764

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements. Heat analysis is performed per heat as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 ...

Open

7765

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

7766

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for one set per heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

7767

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

7768

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations a...

Open

7769

4.2

AI

No

add date

Tensile and hardness testing are performed in accordance with ASTM A370 or ISO 6892-1, and the material meets the specified tensile and maximum hardness properties of Table 4 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

7770

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

7771

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

7772

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C, minimum absorbed energies of 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal, and sub-size reductio...

Open

7773

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with specified etchants (NaOH/KOH for intermetallics, oxalic acid or V2A plus NaOH/KOH for nitrides/carbides) after final polishing, fulfilling the requirement for metallographic preparati...

Open

7774

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

7775

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement for distribution and size of intermetallic phases. So...

Open

7776

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

7777

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7778

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

7779

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

7780

4.4.2

AI

No

add date

No provided documentation explicitly prohibits intermetallic phases and/or precipitates when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10μm, which does not meet the stricter client requirement. Source: ...

Open

7781

4.4.3

AI

No

add date

Ferrite content is measured as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

7782

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corr...

Open

7783

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

7784

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is fulfilled or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

7785

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite content, and microstructure requirements, and is qualified per NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

7786

4.5

AI

No

add date

Requirement for no pitting at 20X magnification and weight loss less than 1.0 g/m² is met by the corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours, with criteria explicitly matching the requirement for DMV 25.7N. Source: DMV_STANDARD_BO...

Open

7787

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

7788

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed after all processing steps, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non...

Open

7789

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed. For OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at extra cost and require technical consul...

Open

7790

5.2

AI

No

add date

No provided document explicitly confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that the required NDE process is feasible for the specified pipe size at the plant. Source: DMV_STA...

Open

7791

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the requested pipe, with no overriding tolerances specified in the customer inquiry or drawing. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General infor...

Open

7792

8.0

AI

No

add date

Marking per ASTM A790 §14 and Montbard standard practices includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAN...

Open

7793

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

7794

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

7795

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers as specified in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

7796

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR as required for qualification for the size and product form on ...

Open

7797

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with required traceability and documentation for TechnipFMC as specified in SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

7798

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control and reference to the relevant standards throughout the specification. Source: DMV_STANDARD_BOOK/02-04-0...

Open

7799

10.2

AI

No

add date

No evidence is provided that the required documentation and certification details—such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and resu...

Open

7800

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all standard, supplementary, and testing requirements. M-650 qualification is confirmed for the required wall thickness. Source: DM...

Open

7801

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782, and there is no confirmation of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Diges...

Open

7802

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, fulfilling the requirement for manufacturer and process qualification and compliance with ...

Open

7803

3.1

AI

No

add date

AOD or equivalent refining is used 100% for DMV 25.7N, and chemical analysis complies with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7804

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed by supplier certification and heat analysis for each heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 ...

Open

7805

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification will state heat treatment condition as per ASTM A790. Pipes are processed to ensure ...

Open

7806

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for testing per heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

7807

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

7808

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified t...

Open

7809

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 as required for DMV 25.7N (UNS S32760). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

7810

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

7811

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness required for testing. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-...

Open

7812

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; the specified pipe dimensions allow for transverse Charpy V-notch...

Open

7813

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching to detect intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

7814

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution for detecting ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

7815

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

7816

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are reported with representative micrographs showing the presence and location of intermetallic phases. S...

Open

7817

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, reported at actual magnification and including a scale bar, and structure free from intermetallic precipitates. Source: DMV_STANDARD_...

Open

7818

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria based on CVN and corrosion...

Open

7819

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully fulfilled. Source: DMV_STA...

Open

7820

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

7821

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance is based on im...

Open

7822

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in accordance with ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

7823

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or mentioned in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

7824

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

7825

4.5

AI

No

add date

Requirement for no pitting at 20X magnification and weight loss < 1.0 g/m² is met per corrosion test section (§11) of NORSOK MDS D51 Rev 06, specifying ISO 17781 G48 Method A with these acceptance criteria. DMV 25.7N complies with these requirements....

Open

7826

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, or their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in...

Open

7827

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

7828

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51 are not fully addressed; feasibility of required NDE methods (Eddy current, Ultrasonic, Hydrostatic) for the specified OD is not confirmed or is only available at extra cost, and full-len...

Open

7829

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair; NDE acceptance criteria and related rejection/repair policy are not explicitly stated or are n...

Open

7830

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding TechnipFMC specification indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a A 376-0...

Open

7831

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7832

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

7833

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

7834

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

7835

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

7836

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification dem...

Open

7837

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products being delivered as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

7838

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

7839

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of required metallurgical and non-destructive testing. Only general practic...

Open

7840

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified up to the required wall thickness...

Open

7841

1.0

AI

No

add date

No evidence that the supplier is qualified for DMV 25.7N, WT 18.26 mm per NORSOK M-650/ISO 17782 or that QTR/MPCR documentation is available for review as required by the specification. Accreditation for the requested wall thickness is not explicitly...

Open

7842

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process follows M-650 (or ISO 17782) qualified procedures, fulfilling the requirement for manufacturer and process qualification and complianc...

Open

7843

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7844

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits in Table 2, including PREN ≥ 40, as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7845

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

7846

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

7847

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

7848

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests are performed at the requ...

Open

7849

4.2

AI

No

add date

Tensile testing is performed at room temperature per required standards, with mechanical properties and hardness meeting Table 4 and NORSOK MDS D51 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

7850

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

7851

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible as the wall thickness (18.26 mm) exceeds the minimum required for valid specimens for NPS 8 pipe. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12...

Open

7852

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C (transverse: 45 J avg/35 J single, longitudinal: 65 J avg/50 J single if transverse not possible). The specified pipe dimensions allow for required transverse Charpy...

Open

7853

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

7854

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

7855

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

7856

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STANDA...

Open

7857

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

7858

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

7859

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

7860

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

7861

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

7862

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS ...

Open

7863

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) performed in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

7864

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified according to NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

7865

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A, matching the client's specification exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

7866

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destru...

Open

7867

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

7868

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled. Available documents only reference ASTM A790/A999 NDE, destructive tests, or limited NDE feasibility (eddy current, hydrostatic, ultrasonic) f...

Open

7869

5.2

AI

No

add date

No provided documentation explicitly states that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor confirms that NDE is performed as standard for the requested dimension at Montbard. Requireme...

Open

7870

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 unless otherwise specified, with no overriding requirements indicated in the customer specification or drawing. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tole...

Open

7871

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7872

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

7873

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' confirming the requirement is met. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev...

Open

7874

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

7875

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

7876

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification de...

Open

7877

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body and provides EN 10204 type 3.1 certificates traceable to the products, fulfilling the documentation and quality-assurance requirements of SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

7878

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications and practices as specified. Source: DMV_STANDARD_BOOK/02-04...

Open

7879

10.2

AI

No

add date

Most documentation and certification requirements are addressed, including NORSOK M-650/ISO 17782 identification, steel melting practice and refining method, heat treatment condition, and test results. However, the actual steel producer's name is not...

Open

7880

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the item table and confirmed by the digest, including all mechanical, chemical, and testing requirements. Source: DMV_STANDARD_BOOK/02-04-03 - ...

Open

7881

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not to ISO 17782, as explicitly required. No evidence of QTR/MPCR availability is provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7882

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to 31.75 mm WT, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

7883

3.1

AI

No

add date

AOD or equivalent steel refining is required and used for 100% of production, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7884

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the requirement table and DMV material composition conforms to these requirements with heat analysis and supplier certification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detai...

Open

7885

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Free circulation of heating and ...

Open

7886

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

7887

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with frequency and method matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

7888

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per ASTM A790 and NORSOK M...

Open

7889

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

7890

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

7891

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, meeting the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 -...

Open

7892

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C (transverse: 45/35 J, longitudinal: 65/50 J) for thickness >6mm, and the specified pipe dimensions allow for required testing directions and specimen sizes. Source: D...

Open

7893

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants and electrolytic etching after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/...

Open

7894

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

7895

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

7896

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

7897

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

7898

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

7899

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10µm and not distributed over the whole specimen, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to ge...

Open

7900

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

7901

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

7902

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

7903

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

7904

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive and microstructural tests (tensile, impact, corrosion, microstructure, ferrite), with explicit compliance and M-650 qualification up to the required...

Open

7905

4.5

AI

No

add date

DMV 25.7N meets the pitting corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours, with no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

7906

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

7907

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available and applicable for the requested pipe dimensions; requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12...

Open

7908

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed. Standard NDE methods (EC, UT, hydrostatic) for the required OD are only available at extra cost or require technical consultation, and full-length dy...

Open

7909

5.2

AI

No

add date

No provided document explicitly states that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, and standard NDE for the requested OD is not available at Montbard to guarantee this req...

Open

7910

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A ...

Open

7911

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7912

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 §14, requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring compliance with the requirement for traceability...

Open

7913

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

7914

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

7915

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

7916

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for UNS S32760/DMV25.7N up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

7917

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to the delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

7918

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

7919

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, ladle chemical analysis, solution annealing parameters, or actual metallurgical and non-...

Open

7920

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with all material, manufacturing, and testing requirements met, and M-650 qualification confirmed for the required wall thickness. Source: DM...

Open

7921

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782; no evidence of full qualification to both standards or availability of QTR/MPCR documentation is provided as required by the specification. Source: 02-04-03 - Digest NORSOK MD...

Open

7922

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

7923

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7924

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Heat analysis is performed per heat and matches the required limits for all elements liste...

Open

7925

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compliance...

Open

7926

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

7927

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

7928

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per ASTM A790 and NORSOK re...

Open

7929

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the specified tensile and maximum hardness properties of Table 4 as required by NORSOK MDS D51. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

7930

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

7931

4.3

AI

No

add date

Pipe dimensions exceed minimum wall thickness for Charpy V-notch testing per ASTM and ISO standards; testing as specified is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - ...

Open

7932

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements, including Charpy V-notch testing at -466C with minimum absorbed energy values (transverse: 45 J average/35 J single, longitudinal: 65 J average/50 J single) and sub-size red...

Open

7933

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

7934

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N meets the chemical composition requirements per Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

7935

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

7936

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

7937

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs are included, noting and recording the presence and location of intermetallic phases. S...

Open

7938

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

7939

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 requires reporting of intermetallic phases, with acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - S...

Open

7940

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. No source fully prohibits intermetallics as required by th...

Open

7941

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

7942

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781 with specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requirement f...

Open

7943

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

7944

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is fulfilled or referenced in the provided documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

7945

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified according to NORSOK M-650/ISO 17782. Source: DMV_STANDARD_...

Open

7946

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

7947

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destruct...

Open

7948

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, meeting the requirement for both standard and dimensional capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02...

Open

7949

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N within the specified wall thickness, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 requirements. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

7950

5.2

AI

No

add date

NDE per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 is not confirmed; only ASTM A790/A999 NDE is detailed. For the requested OD, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at extra cost. Full-length ...

Open

7951

5.2

AI

No

add date

No explicit statement or evidence that indications greater than the calibration notch are treated as defects requiring rejection or repair; NDE acceptance criteria and standard NDE methods for the specified OD are not confirmed as feasible or standar...

Open

7952

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and ASTM A999 as required, with no deviations specified by the customer. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A 376-0...

Open

7953

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

7954

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

7955

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7956

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

7957

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

7958

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification dem...

Open

7959

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

7960

10.2

AI

No

add date

Certification is provided to EN 10204 Type 3.1, including all information required by ASTM A790 and NORSOK M-630, and validated by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAN...

Open

7961

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice and refining method, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the actual steel produce...

Open

7962

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with all relevant mechanical, chemical, and testing requirements fulfilled for 25 Cr Duplex stainless steel...

Open

7963

1.0

AI

No

add date

Manufacturing process is qualified according to NORSOK M-650/ISO 17782, covering essential variables and limitations for the exact product supplied. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

7964

7.0

AI

No

add date

Finished pipes are required to be white pickled or bright annealed according to both ASTM A790 and NORSOK MDS S01 Rev 05, fulfilling the requirement. Source: ASTM A790, NORSOK MDS S01 Rev 05

Open

7965

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the inquiry WT is 18.26 mm, within the accredited range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

7966

3.2

AI

No

add date

DMV 25.7N pipes are solution annealed and water quenched per ASTM A790, with furnaces qualified to NORSOK M-650, and heat treatment ensures free circulation of media around each pipe as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

7967

4.1

AI

No

add date

There is no explicit confirmation that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790; some tests are mentioned but not all, and lot-w...

Open

7968

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

7969

4.1

AI

No

add date

Test sampling requirements for test direction (longitudinal or transverse), CVN impact testing, and specific thickness locations are not fully addressed; no explicit confirmation of compliance with all aspects of Table 3 is provided, and CVN, corrosi...

Open

7970

4.2

AI

No

add date

Tensile testing is performed at room temperature with criteria meeting or exceeding Table 4 requirements for DMV 25.7N, and hardness testing is conducted with results provided in HRC. Compliance with ASTM A790 and NORSOK MDS D51 ensures fulfillment o...

Open

7971

4.2

AI

No

add date

Mechanical property values for tensile strength, yield strength, elongation, and hardness for DMV 25.7N (UNS S32760/S32750) are not provided in the referenced documents, so fulfillment of the requirement cannot be confirmed. Source: DMV_STANDARD_BOOK...

Open

7972

4.3

AI

No

add date

No evidence that Charpy V-notch testing is performed or that results meet ASTM A370, ASTM A1058, ISO 148-1, or Table 5 requirements; only feasibility is confirmed for the specified dimensions, not actual compliance or testing execution. Source: DMV_S...

Open

7973

4.3

AI

No

add date

Impact testing at -466C with specified absorbed energy values is feasible and can be fulfilled for pipe with 18.26mm wall thickness, as transverse specimens are possible for NPS 8 at this thickness. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

7974

4.4.1

AI

No

add date

No evidence of metallographic preparation or examination per ISO 17781, nor use of the specified etchant for 25 Cr Duplex stainless steels; only grain size measurement for austenitic materials is addressed, not duplex grades. Source: DMV_STANDARD_BOO...

Open

7975

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination or to show ferrite balance and intermetallic phases is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12...

Open

7976

4.4.2

AI

No

add date

Micrographic examination requires the microstructure to be basically free from intermetallic phases, allowing isolated phases if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - S...

Open

7977

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided or addressed in the relevant documentation or comments. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/1...

Open

7978

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at 400x minimum magnification with actual magnification and scale bar when intermetallic phases are not detected. Partial mention of 400x magnificatio...

Open

7979

4.4.2

AI

No

add date

No relevant documents address the presence, reporting, or acceptance criteria for centerline intermetallic stringers, nor their linkage to CVN and corrosion test results in case such stringers are present. Source: DMV_STANDARD_BOOK/12-03-03 - Grain S...

Open

7980

4.4.2

AI

No

add date

NORSOK MDS D41 and D51 require microstructure to be 'basically free from intermetallic precipitates' but allow isolated precipitates below 10μm, which does not fully prohibit intermetallic phases/precipitates if CVN testing cannot be completed as req...

Open

7981

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided or addressed in the relevant documents. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Micrograph...

Open

7982

4.4.3

AI

No

add date

No acceptance criteria or results for micrographic examination are provided for DMV 25.7N; referenced documents either do not address micrographic examination or specify that grain size examination is not applicable to duplex/super-duplex steels. Sou...

Open

7983

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly stated and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

7984

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided in the available documentation or specifications. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

7985

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are provided in the referenced documents, making validation impossible based on the available information. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-...

Open

7986

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria: no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

7987

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

7988

5.2

AI

No

add date

No explicit confirmation of 100% ultrasonic testing per ASTM E213 or ISO 10893-10 after all processing, nor evidence of compliance with calibration notch requirements or process sequence is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

7989

5.2

AI

No

add date

100% qualitative anti-mixing PMI check is performed on standard production at Montbard using appropriate instruments, fulfilling general acceptance criteria for PMI under NDE. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive tes...

Open

7990

5.2

AI

No

add date

No provided document explicitly states that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair of pipe and tubing as specified by the requirement. NDE acceptance criteria are not co...

Open

7991

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for the requested product are confirmed to be per the applicable ASTM standards (including ASTM A 790 with A 999 for tolerances), with no overriding TechnipFMC specifications referenced. Source: DMV_STAN...

Open

7992

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

7993

10.0

AI

No

add date

No evidence of an ISO 9001 or equivalent quality-assurance system certified by a competent EEA body is provided for the manufacturer or Montbard plant. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Certification...

Open

7994

10.1

AI

No

add date

No evidence that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body is provided. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-03 - Cer...

Open

7995

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

7996

10.2

AI

No

add date

No explicit evidence that documentation traceable to the products and to be transmitted to TechnipFMC (as per SIR205) will be provided; only general information on inspection and certification is given without confirmation of transmission or traceabi...

Open

7997

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control for mill inspection as required. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-...

Open

7998

10.2

AI

No

add date

No provided document contains the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or test results for metallu...

Open

7999

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all standard, supplementary, and testing requirements, and are M-650 qualified up to the required wall thickness for 25 Cr Duplex s...

Open

8000

1.0

AI

No

add date

Supplier is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N but not accredited to ISO 17782; full qualification to NORSOK M-650/ISO 17782 and documentation availability are not confirmed for the exact product supplied as required. Source: DMV_STAN...

Open

8001

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

8002

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition conforms to the specified requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8003

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat to ensure conformity with the standard....

Open

8004

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782, and procedures ensure free circulation of heating and cooling media du...

Open

8005

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

8006

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

8007

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specifi...

Open

8008

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with material meeting the tensile and maximum hardness properties of Table 4 as required by NORSOK MDS D51. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

8009

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 06 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

8010

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

8011

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements at -46°C, with minimum absorbed energy values for both transverse and longitudinal directions, and the specified pipe dimensions allow for required testing orientation and specimen size...

Open

8012

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

8013

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

8014

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

8015

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

8016

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

8017

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

8018

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates below 10µm, which does not meet the stricter client requirement of no interm...

Open

8019

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

8020

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

8021

4.4.3

AI

No

add date

Microstructure examination per ISO 17781 is specified, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requirement for...

Open

8022

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8023

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

8024

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8025

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

8026

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destruct...

Open

8027

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

8028

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/NORSOK M-650/ISO 17782 are not confirmed as fulfilled. Provided documents only confirm general NDE per ASTM A790/A999, lack explicit confirmation of NORSOK-specific NDE, and indicate feas...

Open

8029

5.2

AI

No

add date

No evidence that NDE acceptance criteria require rejection or repair of indications greater than the calibration notch; standard NDE is not available for the requested OD at Montbard, so the requirement cannot be fulfilled for this size or confirmed ...

Open

8030

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790/A999) for the specified pipe dimensions, with no deviations or special tolerances stated by the customer or TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General i...

Open

8031

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

8032

8.0

AI

No

add date

Marking per ASTM A790 and standard plant methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/...

Open

8033

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 explicitly states 'Weld repairs not acceptable,' directly fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8034

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

8035

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

8036

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

8037

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling supplier qualification documentation requirem...

Open

8038

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

8039

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Cert...

Open

8040

10.2

AI

No

add date

Most documentation and certification requirements are addressed, but the actual steel producer of the starting material is not provided (only country of origin is given). No specific documentation or test results for the actual order are evidenced, a...

Open

8041

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, Digest NORSOK MDS D51 Rev 06.d...

Open

8042

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence provided for QTR/MPCR availability for review by TechnipFMC as specified. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8043

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, with manufacturing process qualified to M-650 (or ISO 17782), and compliance with NORSOK M-630 MDS D51 Rev. 6 is referenced. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

8044

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8045

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements, with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/0...

Open

8046

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and furnace qualification ensures free circulation of heating/cooling media. MST-Tubes is M-650 accre...

Open

8047

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

8048

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for sampling requirements, fulfilling the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

8049

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified t...

Open

8050

4.2

AI

No

add date

Tensile testing is performed in accordance with ASTM A370 or ISO 6892-1, and the material meets the required tensile and maximum hardness properties of Table 4 for DMV 25.7N as specified in NORSOK MDS D51 and ASTM A790. Source: DMV_STANDARD_BOOK/02 -...

Open

8051

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

8052

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness requirements for these standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive...

Open

8053

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible). The specified pipe dimensions allow ...

Open

8054

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with specified etchants for intermetallic phases and ferrite balance after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spec...

Open

8055

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

8056

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

8057

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

8058

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

8059

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

8060

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

8061

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

8062

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with required etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impac...

Open

8063

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

8064

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is fulfilled or documented for the requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

8065

4.5

AI

No

add date

DMV 25.7N meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content. Source: DMV...

Open

8066

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and DMV 25.7N complies. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

8067

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

8068

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, which are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-0...

Open

8069

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT) is detailed, but there is no explicit confirmation that NORSOK-specific NDE requirements are met. For the specified OD, eddy current is not feasible, and hydrostatic/ultrasonic tests are only available ...

Open

8070

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor is there confirmation that NDE methods with this acceptance criterion are standardly appli...

Open

8071

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standards (A999), with no deviations or special tolerances indicated by TechnipFMC. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.do...

Open

8072

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

8073

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

8074

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8075

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

8076

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

8077

10.1

AI

No

add date

MST-Tubes is M-650 accredited for UNS S32760/DMV25.7N up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demon...

Open

8078

10.2

AI

No

add date

Certification to ISO 9001 by a competent body and documentation traceable to delivered products are provided as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

8079

10.2

AI

No

add date

Certification is provided to EN 10204 Type 3.1, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference). Source: DMV_STANDARD_BOOK/02...

Open

8080

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, with minimum absorbed energy values for transverse and longitudinal specimens, and the specified pipe dimensions allow for required transverse Charpy V-notch testin...

Open

8081

8.0

AI

No

add date

Marking includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAND...

Open

8082

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or results of all required metallurgical and non-destructive testing. Only general statem...

Open

8083

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, Digest NORSOK MDS D51 Rev 06.d...

Open

8084

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782; full qualification per both standards is not demonstrated and availability of QTR/MPCR is not confirmed. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8085

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

8086

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8087

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements, with heat analysis and supplier certification provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02...

Open

8088

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

8089

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for one set per heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

8090

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

8091

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specifi...

Open

8092

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

8093

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

8094

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and meets the requirements of ASTM A370, ASTM A1058, or ISO 148-1. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

8095

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

8096

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with specified etchants for intermetallic phases and ferrite balance after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

8097

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

8098

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

8099

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included with presence and location of intermetallic phases noted and recorded as required. Source...

Open

8100

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

8101

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

8102

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates below 10μm, which does not meet the requirement of not permitting any interm...

Open

8103

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

8104

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

8105

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

8106

4.5

AI

No

add date

Applicable standards are referenced, but there is no explicit confirmation that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or fulfilled. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montb...

Open

8107

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, chemical composition, ferrite content, corrosion, and impact requirements; manufacturing and qualification processes are acc...

Open

8108

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

8109

5.1

AI

No

add date

No evidence provided regarding qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montb...

Open

8110

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within capability range. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02...

Open

8111

5.2

AI

No

add date

NDE per ASTM A790 and NORSOK M-630 MDS D51 is required, but there is no explicit evidence that NORSOK-specific NDE requirements are addressed or qualified. For the specified OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/ultraso...

Open

8112

5.2

AI

No

add date

None of the reviewed documents explicitly confirm that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor do they specify this NDE acceptance criterion for the requested produc...

Open

8113

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and ASTM A999 as required, with no overriding tolerances specified by the customer. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01...

Open

8114

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

8115

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and standard practice at Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_S...

Open

8116

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8117

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

8118

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

8119

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N up to the required wall thickness, fulfilling the qualification requirement for the specified size and product ...

Open

8120

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

8121

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary or QTR...

Open

8122

10.2

AI

No

add date

No provided document contains all required documentation and certification details, including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and test results. One d...

Open

8123

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

8124

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782, nor confirmation of QTR/MPCR availability for review. MST-Tubes is accredited to NORSOK M-650 but not ISO 17782, which is explicitly required by the specification. Source: DMV_...

Open

8125

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

8126

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8127

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 06, including PREN ≥ 40 and all specified element limits. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NO...

Open

8128

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

8129

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

8130

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

8131

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specified...

Open

8132

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, with mechanical properties and maximum hardness meeting Table 4 requirements for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

8133

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

8134

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

8135

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energy values of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal; the specified pipe dimensions ...

Open

8136

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

8137

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

8138

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

8139

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

8140

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

8141

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

8142

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

8143

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

8144

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with required etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impac...

Open

8145

4.4.3

AI

No

add date

Ferrite content specified as 35% to 60% per ISO 17781 and ASTM E1245; DMV 25.7N complies. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8146

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

8147

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, chemical composition, ferrite content, impact, corrosion resistance, and microstructure requirements. Source:...

Open

8148

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02...

Open

8149

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

8150

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is confirmed for the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12...

Open

8151

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/650 are not fully addressed; standard NDE methods (EC, UT, hydrostatic) for the specified OD and length are only available at extra cost or require special consultation, and full-length d...

Open

8152

5.2

AI

No

add date

No explicit confirmation that NDE indications greater than the calibration notch are treated as defects requiring rejection or repair; referenced standards and plant feasibility data do not specify this acceptance criterion for the requested product ...

Open

8153

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790/A999) for the requested pipe, with no deviations or overrides specified by the customer or in the drawing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/07...

Open

8154

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

8155

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body as per the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

8156

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for UNS S32760/DMV25.7N up to the required wall thickness for the specified size and product form. Source: DMV_STANDARD_BOOK/...

Open

8157

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to the delivered products, fulfilling the requirement for documentation traceable to the products as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

8158

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications and plant documentation. Source: DMV_STANDARD_BOOK/02-04-03 - Dig...

Open

8159

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. Other required ...

Open

8160

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified up to the required wall thickness....

Open

8161

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D5...

Open

8162

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process follows M-650 (or ISO 17782) qualified procedures, fulfilling the requirement for manufacturer and process qualification per NORSOK M-...

Open

8163

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8164

3.1

AI

No

add date

DMV 25.7N (UNS S32760) chemical composition matches the requirements of Table 2, including PREN ≥ 40, and complies with ASTM A790 and NORSOK MDS D51 Rev 06 standards. Heat analysis and supplier certification are performed per heat as required. Source...

Open

8165

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling (including water quenching) per ASTM A790; furnaces and process are qualified to NORSOK M-650/ISO 17782; pipes are arranged to ensure free circulation of heating and cooling media during hea...

Open

8166

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

8167

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

8168

4.1

AI

No

add date

DMV 25.7N seamless pipes are tested per NORSOK MDS D51/ASTM A790 requirements: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure at specified thickness locations. The order...

Open

8169

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

8170

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

8171

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness (>6mm), fulfilling the requirement. Source: 12-03-02 - Impact Test for hot finished products.doc

Open

8172

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact test requirements: Charpy V-notch at -46°C, minimum average 45 J and single 35 J in transverse direction (for thickness ≥6 mm), and if not possible, longitudinal direction minimum average 65 J and s...

Open

8173

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

8174

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

8175

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

8176

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

8177

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

8178

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

8179

4.4.2

AI

No

add date

The available specifications allow isolated intermetallic precipitates below 10μm, but do not prohibit all intermetallic phases and/or precipitates if CVN testing cannot be completed, as required by the client. The stricter client requirement is not ...

Open

8180

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

8181

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Structure must be basically free from intermetallic precipitates; isolated precipitates allowed if not d...

Open

8182

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

8183

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including destructive, micrographic, corrosion tests, ferrite content, heat treatment, and manufacturing process requirements. Source: DMV_STANDARD_BOOK/02...

Open

8184

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A @ 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and compliance is confirmed. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

8185

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

8186

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed on the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

8187

5.2

AI

No

add date

There is no evidence that NDE acceptance criteria per ASTM A790, NORSOK M-630 MDS D51 Rev 6, or NORSOK M-650/ISO 17782 are fulfilled. Required NDE methods (eddy current, ultrasonic, hydrostatic) are either not feasible, only available at extra cost, ...

Open

8188

5.2

AI

No

add date

No provided documentation confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that this NDE criterion is standardly performed or feasible for the specified pipe dimension at Montbard....

Open

8189

6.0

AI

No

add date

Dimensional tolerances are confirmed as per the applicable ASTM standard (A790/A999) for the specified product, with no overriding requirements from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/0...

Open

8190

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

8191

8.0

AI

No

add date

Marking is performed per ASTM A790, requiring full traceability to melt and heat treatment lot, with mandatory marking of heat number and DMV lot number on all pipes. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDAR...

Open

8192

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8193

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

8194

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

8195

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

8196

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

8197

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

8198

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and full metallurgical and non-destructive test results are ...

Open

8199

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all standard and supplementary requirements, and are M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-03-01 - Digest A...

Open

8200

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR availability as required. Full qualification to both NORSOK M-650 and ISO 17782 is not demonstrated for the exact product su...

Open

8201

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, with manufacturing process qualified to M-650 (or ISO 17782), and compliance with NORSOK M-630 MDS D51 Rev. 6 is confirmed. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

8202

3.1

AI

No

add date

AOD or equivalent refining is required and used for DMV 25.7N, and chemical composition complies with Table 2 of ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8203

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements. Heat analysis is performed per heat as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 ...

Open

8204

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

8205

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

8206

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Dig...

Open

8207

4.1

AI

No

add date

Test sampling for seamless pipes per ASTM A790 and NORSOK MDS D51, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled...

Open

8208

4.2

AI

No

add date

Tensile testing is performed at room temperature with required properties met; ASTM A790 references ASTM A370 for mechanical testing, fulfilling the requirement for testing per ASTM A370 or ISO 6892-1 and meeting Table 4 properties. Source: DMV_STAND...

Open

8209

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 06 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

8210

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

8211

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal, including reduction factors for sub...

Open

8212

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

8213

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant for ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

8214

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

8215

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

8216

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

8217

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 requires reporting of intermetallic phases, with acceptance based on CVN and corrosion test results if such phases are present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STAN...

Open

8218

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates, which does not meet the stricter client requirement of not permitting any i...

Open

8219

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

8220

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

8221

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev ...

Open

8222

4.5

AI

No

add date

No explicit evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 will be performed or is referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

8223

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 are fully met, including compliance for destructive and micrographic tests, solution annealing, ferrite range, absence of intermetallics, and correct test methods and values. S...

Open

8224

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8225

4.5

AI

No

add date

Requirement for no pitting at 20X magnification and weight loss < 1.0 g/m² is met by corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours, with specified criteria confirmed for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

8226

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

8227

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

8228

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/650 are not fully addressed. Only general NDE (hydrostatic/EC/UT) per ASTM A999 is confirmed, but NORSOK-specific requirements are not evidenced. For the requested OD, eddy current and ul...

Open

8229

5.2

AI

No

add date

No provided document explicitly states that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, nor confirms that NDE with this acceptance criterion will be performed as standard for t...

Open

8230

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are confirmed to be per the applicable ASTM standard (ASTM A999), with no deviations specified by TechnipFMC. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc,...

Open

8231

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

8232

8.0

AI

No

add date

Marking is performed per ASTM A790 §14 and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

8233

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

8234

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system certified within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

8235

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

8236

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, are provided and meet the requirement for documentation traceable to the delivered products as...

Open

8237

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control and reference to required content such as heat treatment, steel manufacturer, and manufacturing summary...

Open

8238

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants and electrolytic etching after final polishing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

8239

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. No evidence is ...

Open

8240

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

8241

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N but not to ISO 17782, as explicitly required. No evidence provided for QTR/MPCR availability for review or full compliance with both standards and essential variables/limitations as speci...

Open

8242

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

8243

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8244

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN ≥ 40, as required by ASTM A790 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat to ensure compliance. Source: DMV_STANDA...

Open

8245

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compliance with th...

Open

8246

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

8247

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, fulfilling the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed ...

Open

8248

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests are performed at the spec...

Open

8249

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the specified tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

8250

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 and ASTM A790 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW for S32760. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

8251

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact ...

Open

8252

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C for thickness ≥6 mm, and the specified pipe dimensions allow for required transverse and longitudinal Charpy V-notch testing at the specified energies and temperature...

Open

8253

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases is required, in accordance with ISO 17781 Appendix B, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

8254

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

8255

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

8256

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

8257

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

8258

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

8259

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

8260

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

8261

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8262

4.5

AI

No

add date

No direct evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or confirmed. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

8263

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 (ASTM A790, NORSOK M-630, M-650/ISO 17782) are fully met, including compliance for destructive and microstructural tests (tensile, impact, corrosion, microstructure, ferrite) w...

Open

8264

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

8265

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montb...

Open

8266

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

8267

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782, as explicitly required. No evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8268

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

8269

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not explicitly addressed; only ASTM A790/A999 NDE is confirmed. For OD 219.1 mm, standard NDE methods (eddy current, ultrasonic, hydrostatic) are not fully feasible or re...

Open

8270

5.2

AI

No

add date

No provided document confirms that indications greater than the calibration notch are classified as defects requiring rejection or repair, nor is there evidence that NDE methods with this acceptance criterion are standardly available for the requeste...

Open

8271

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the requested pipe, with no deviations or special tolerances specified by the customer or drawing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/07-01 - General ...

Open

8272

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

8273

8.0

AI

No

add date

Marking is performed according to ASTM A790, requiring full traceability to melt and heat treatment lot, with mandatory marking of heat number and DMV lot number ensuring compliance with the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NO...

Open

8274

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for DMV 25.7N seamless pipe, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

8275

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA and specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

8276

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

8277

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness for the specified size and product form. Source: DMV_STANDARD_BO...

Open

8278

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to delivered products, fulfilling the documentation and traceability requirement for TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

8279

10.2

AI

No

add date

EN 10204 Type 3.1 material certificate is provided as standard, including all information required by ASTM A790 and NORSOK M-630, and validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

8280

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution annealing parameters, an...

Open

8281

1.0

AI

No

add date

DMV 25.7N seamless pipe is specified, with compliance to ASTM A790 and NORSOK M-630 MDS D51 rev. 6 confirmed, and M-650 qualification for DMV 25.7N up to the required wall thickness is met. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

8282

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8283

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN ≥ 40, as required by ASTM A790 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat to ensure compliance. Source: DMV_STANDA...

Open

8284

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

8285

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

8286

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

8287

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified t...

Open

8288

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

8289

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: minimum tensile strength 750 MPa, yield strength 550 MPa, elongation 25%, and maximum hardness 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

8290

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions (OD 219.1 mm, WT 18.26 mm), which exceed the minimum required wall thickness for testing. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructi...

Open

8291

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for required testing directions. Source: DMV_STANDAR...

Open

8292

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants and electrolytic etching after final polishing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

8293

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

8294

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

8295

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781, with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STAND...

Open

8296

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, and the structure must be free from intermetallic precipitates, fulfilling the requirement for a representative micrograph at or near mid-wall thickness, ...

Open

8297

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

8298

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully fulfilled. Source: DMV_STA...

Open

8299

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

8300

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impa...

Open

8301

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is specified and fulfilled for DMV 25.7N according to NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

8302

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

8303

4.5

AI

No

add date

DMV 25.7N complies with all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive, micrographic, corrosion tests, ferrite content, and heat treatment, with M-650 qualification for the specified grade and wall thickness. So...

Open

8304

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

8305

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

8306

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed on the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

8307

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed. Provided documents only partially address ASTM A790/A999 NDE, and Montbard plant NDE methods (hydrostatic, ultrasonic, eddy current, dye penetrant) a...

Open

8308

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor is there confirmation that the required NDE methods and acceptance criteria will be applied for ...

Open

8309

6.0

AI

No

add date

Dimensional tolerances for the specified pipe are per the applicable ASTM standard (ASTM A790 referencing ASTM A999), with no evidence of override by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - ...

Open

8310

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

8311

8.0

AI

No

add date

Marking is per ASTM A790 and includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standard marking fea...

Open

8312

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

8313

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

8314

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

8315

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, and the QTR number is included in the certificate, fulfilling the requirement for supplier qualification documentation per SIR131. Source: DMV_STANDARD_BOOK/0...

Open

8316

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

8317

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing M-650/ISO17782 qualification where applicable. Source: DMV_STANDARD_BOOK/02-04-03 -...

Open

8318

10.2

AI

No

add date

No provided documentation includes all required items: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis (ladle), solution annealing temperature/holdin...

Open

8319

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all chemical, mechanical, manufacturing, and testing requirements. M-650 qualification is confirmed for the required wall thickness. Source: DMV_ST...

Open

8320

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability or full compliance with both NORSOK M-650/ISO 17782 as required by the specification. Source: DMV_STAND...

Open

8321

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, with manufacturing process qualified to M-650 (or ISO 17782) and compliance with NORSOK M-630 MDS D51 Rev. 6 confirmed. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

8322

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8323

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat to ensure compliance. Sour...

Open

8324

3.2

AI

No

add date

Manufacturing process is qualified to NORSOK M-650, heat treatment is solution annealed followed by accelerated cooling per ASTM A790, furnaces are qualified per NORSOK M-650/ISO 17782, and free circulation of heating and cooling media is ensured dur...

Open

8325

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

8326

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

8327

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per NORSOK MDS D51/ASTM A7...

Open

8328

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-...

Open

8329

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

8330

4.3

AI

No

add date

Pipe dimensions exceed the minimum required wall thickness for Charpy V-notch testing as per ASTM A370, ASTM A1058, or ISO 148-1, so testing is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive ...

Open

8331

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible), with reduction factors for sub-size ...

Open

8332

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

8333

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

8334

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

8335

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

8336

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

8337

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

8338

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully met. Source: DMV_S...

Open

8339

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: ASTM A 790, NORSOK MDS D51 Rev 06.

Open

8340

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

8341

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

8342

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

8343

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) performed in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

8344

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, as well as manufacturing, heat treatment, and qualification requirements. Source: DMV_STAN...

Open

8345

4.5

AI

No

add date

No pitting at 20X magnification and weight loss less than 1.0 g/m² are met per ISO 17781 G48 Method A; DMV 25.7N complies. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

8346

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

8347

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects is performed in accordance with ASTM E213 and ISO 10893-10 for the required dimensions; acceptance of ASTM E213 implies compliance with reference notch calibration requirements. Source: DMV_STANDARD_BO...

Open

8348

5.2

AI

No

add date

NDE per ASTM A790 is partially addressed via ASTM A999 (hydrostatic or EC/UT), but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are met. For the specified OD (219.1 mm), eddy current testing...

Open

8349

5.2

AI

No

add date

The available documents do not explicitly confirm that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, and NDE feasibility for the specified OD is limited (eddy current not feasible, ultrasonic ...

Open

8350

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding TechnipFMC specification indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a A 376-0...

Open

8351

8.0

AI

No

add date

Marking is performed according to ASTM A790, requiring full traceability to melt and heat treatment lot, with mandatory marking of heat number and DMV lot number ensuring compliance. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

8352

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

8353

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

8354

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8355

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the specified quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

8356

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for UNS S32760/DMV25.7N up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

8357

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products as required by SIR205 and section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

8358

10.2

AI

No

add date

Certification is provided to EN 10204 Type 3.1, including all information required by ASTM A790 and NORSOK M-630. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certification Montbard plant.doc

Open

8359

10.2

AI

No

add date

Most required documentation and certification details are not provided. EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, melting practice, and heat treatment condition, but the steel producer name is missing (only cou...

Open

8360

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all relevant mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified up to the required wall ...

Open

8361

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

8362

3.1

AI

No

add date

AOD or equivalent refining is used and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8363

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790 as required, with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 7...

Open

8364

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

8365

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

8366

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

8367

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations are all...

Open

8368

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370, and material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORS...

Open

8369

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

8370

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness required by the standards. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished product...

Open

8371

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C (transverse: 45/35 J, longitudinal: 65/50 J) for thickness >6mm, and the specified pipe dimensions allow for required testing directions and specimen sizes. Source: D...

Open

8372

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with specified etchants, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

8373

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

8374

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

8375

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

8376

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

8377

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

8378

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates, which does not meet the stricter client requirement of not permitting any i...

Open

8379

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

8380

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with defined etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact...

Open

8381

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is specified and confirmed for DMV 25.7N as per ISO 17781/ASTM E1245 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

8382

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

8383

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

8384

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

8385

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8386

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

8387

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within machine capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

8388

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790/NORSOK M-630 MDS D51 are not fully met: only general hydrostatic or NDE (EC or UT) per ASTM A999 is confirmed, with no explicit compliance to NORSOK-specific NDE requirements; for OD 219.1 mm, Eddy current is not...

Open

8389

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor that this acceptance criterion is applied in practice for the specified product and NDE methods ...

Open

8390

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790) for the requested pipe dimensions, with no overriding requirements specified by TechnipFMC in the provided context. Source: DMV_STANDARD_BOOK/07-01 - G...

Open

8391

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

8392

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot, and the marking methods used (indelible black ink and vibro-etching) include the heat number and DMV lot number, ensuring compliance. Source: DMV_STANDARD_BOOK/02-04-03 ...

Open

8393

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

8394

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

8395

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

8396

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

8397

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to delivered products, fulfilling the requirement for documentation to be transmitted to TechnipFMC and traceable as per SIR205. Source: DMV_STANDARD_BOOK/0...

Open

8398

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and covering heat treatment, steel manufacturer, melting and refining practice, and M-650/ISO17782 manufactur...

Open

8399

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

8400

10.2

AI

No

add date

EN 10204 3.1 certificates include most required information (NORSOK M-650/ISO 17782 QTR number, steel melting practice, heat treatment, test results), but only the country of origin of the steel supplier is provided, not the actual steel producer's n...

Open

8401

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of full qualification to both NORSOK M-650/ISO 17782 or availability of QTR/MPCR documentation as required by the specification....

Open

8402

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to M-650 or ISO 17782, meeting the requirement for manufacturer and process qualification with testing per NORS...

Open

8403

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis complies with Table 2 for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8404

3.1

AI

No

add date

DMV 25.7N (UNS S32760) chemical composition matches the requirements of Table 2 and complies with ASTM A790 and NORSOK MDS D51 Rev 06, including PREN ≥ 40 and all specified element limits. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest ...

Open

8405

3.2

AI

No

add date

Manufacturing process is qualified to NORSOK M-650/ISO 17782; heat treatment is solution annealing followed by accelerated cooling as per ASTM A790; compliance with proper heat treatment practices is ensured. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

8406

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

8407

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

8408

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) meets requirements for tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, with transverse...

Open

8409

4.2

AI

No

add date

Tensile testing is performed at room temperature per NORSOK MDS D51 Table 4, meeting the specified mechanical properties, and testing is in accordance with ASTM A370 or ISO 6892-1. Hardness testing is also performed as required. Source: DMV_STANDARD_...

Open

8410

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

8411

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness requirements for testing. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - I...

Open

8412

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with specified minimum absorbed energy values for both transverse and longitudinal directions, and the pipe dimensions allow for required testing directions and spec...

Open

8413

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

8414

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is specified and fulfills the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-...

Open

8415

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

8416

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

8417

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included and a representative micrograph recorded and reported at or near mid-wall thickness if intermetallic phases are not detected, including a scale bar and act...

Open

8418

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

8419

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. No source fully prohibits intermet...

Open

8420

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

8421

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance is based on im...

Open

8422

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

8423

4.5

AI

No

add date

ASTM G48 Method 'A' corrosion testing at 50°C for 24h in accordance with ISO 17781 is not explicitly mentioned or referenced; compliance cannot be confirmed based on the available information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Mo...

Open

8424

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO ...

Open

8425

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

8426

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

8427

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

8428

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR documentation availability. Requirement for qualification to both NORSOK M-650 and ISO 17782 is not fully met and supporting...

Open

8429

5.2

AI

No

add date

NDE per ASTM A790 is partially addressed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are fulfilled. Standard NDE methods (eddy current, hydrostatic, ultrasonic) for the specified OD ar...

Open

8430

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are considered defects requiring rejection or repair; NDE acceptance criteria per the requirement are not confirmed for the specified product and dimension at Montbard. NDT ...

Open

8431

6.0

AI

No

add date

Dimensional tolerances are confirmed as per ASTM A790 and referenced ASTM A999 for seamless pipe, with no overriding requirements from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tole...

Open

8432

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

8433

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot, in accordance with ASTM A790 and standard practice at Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, ...

Open

8434

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

8435

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

8436

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

8437

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size ...

Open

8438

10.2

AI

No

add date

ISO 9001 certification is provided, and documentation including EN 10204 type 3.1 certificates and NORSOK M-650/ISO 17782 manufacturing summary or QTR number is traceable and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

8439

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and compliant with the specified standards. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

8440

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all required metallurgic...

Open

8441

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all referenced mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified for the required wall t...

Open

8442

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

8443

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8444

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits in Table 2, including PREN ≥ 40, and meets the requirements of ASTM A790 and NORSOK MDS D51 Rev 06 as specified in the inquiry. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 -...

Open

8445

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

8446

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

8447

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-0...

Open

8448

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations, all per ASTM A790 and NORSOK requirement...

Open

8449

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1 at room temperature, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

8450

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, fulfilling the client's mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

8451

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

8452

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -466C with minimum transverse values of 45 J (average) and 35 J (single), and longitudinal values of 65 J (average) and 50 J (single) if transverse...

Open

8453

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

8454

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

8455

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

8456

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

8457

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

8458

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, as specified in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

8459

4.4.2

AI

No

add date

No provided documentation prohibits all intermetallic phases and/or precipitates when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10μm, which does not meet the stricter client requirement. Source: DMV_STA...

Open

8460

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

8461

4.4.3

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates allowed if not distributed and <10µm; carbides/nitrides must be reported; acceptance based on impact and corrosion test results. DMV 25.7N is compliant. Sour...

Open

8462

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06 digest. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev...

Open

8463

4.5

AI

No

add date

No explicit evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 will be performed or is referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

8464

4.5

AI

No

add date

DMV 25.7N seamless pipe meets the acceptance criteria for metallurgical properties per ASTM A790 and NORSOK MDS D51 Rev 6, including compliance with chemical composition, heat treatment, mechanical properties, microstructure, and required destructive...

Open

8465

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

8466

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

8467

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed on the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

8468

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not addressed or qualified. For OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at extra cost. Feasibility for requ...

Open

8469

5.2

AI

No

add date

No explicit confirmation of NDE acceptance criteria regarding calibration notch indications or required rejection/repair process; NDE by eddy current is not feasible and ultrasonic is not standard for the requested OD at the plant, so requirement is ...

Open

8470

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standards (ASTM A999), with no overriding requirements from TechnipFMC specified in the context. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDA...

Open

8471

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

8472

8.0

AI

No

add date

Marking per ASTM A790 and plant marking methods ensure mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDA...

Open

8473

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

8474

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

8475

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

8476

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for UNS S32760/DMV25.7N up to the required wall thickness for the specified size and product form. Source: DMV_STANDARD_BOOK/...

Open

8477

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO 17782 manufacturing summary, are provided and fulfill the requirement for documentation traceable to delivered products and transmittal ...

Open

8478

10.2

AI

No

add date

Certification is provided to EN 10204 Type 3.1, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference). Source: DMV_STANDARD_BOOK/02...

Open

8479

10.2

AI

No

add date

No provided documentation includes all required details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all metallurgical...

Open

8480

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, fulfilling the specification for 25 Cr Duplex stainless steel seamless pipes. Source: DMV_STANDARD_BOOK/02-...

Open

8481

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of QTR/MPCR documentation availability as required by the specification. MST-Tubes is NORSOK M-650 accredited for DMV 25.7N but ...

Open

8482

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm for hot finished, 10.925 mm for cold finished), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 require...

Open

8483

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N meets the chemical composition requirements of Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

8484

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the inquiry's wall thickness of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

8485

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed per ASTM A790, manufacturing process and furnaces are qualified according to NORSOK M-650 or ISO 17782, and free circulation of heating/cooling media is ensured by compl...

Open

8486

4.1

AI

No

add date

No evidence that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790; testing frequency and lot-wise compliance are not confirmed in the pr...

Open

8487

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

8488

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no evidence of CVN impact testing, required test directions, or specified sampling locations (outer surface, 1/2 thickness, full thickness) for all tests as required by Table 3. Details on hard...

Open

8489

4.2

AI

No

add date

Tensile testing is performed per ASTM A370, and the material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

8490

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required in Table 4 are not confirmed or are lower than required in the provided documents. Source: DMV_STANDARD_BOOK/02-03-01 - ASTM A 790.docx, DMV_STANDARD_BOOK/02...

Open

8491

4.3

AI

No

add date

No evidence that Charpy V-notch testing is performed or meets ASTM A370, ASTM A1058, ISO 148-1, or Table 5 requirements; only feasibility is indicated for the requested pipe size and wall thickness, not actual compliance or testing results. Source: D...

Open

8492

4.3

AI

No

add date

Impact testing at -46°C with specified absorbed energy values is feasible and can be fulfilled for the pipe with 18.26mm wall thickness, as both longitudinal and transverse specimens can be taken. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for ...

Open

8493

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination per ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Micrograp...

Open

8494

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchants as per ISO 17781 Appendix B for micrographic examination of ferrite balance and intermetallic phases in the provided documents or comments. Requirement not addressed for dup...

Open

8495

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

8496

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

8497

4.4.2

AI

No

add date

No evidence of recording or micrographic documentation (400x minimum) of intermetallic phases is provided; only grain size measurement is addressed or no relevant information is present. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destruct...

Open

8498

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at 400x minimum magnification with a scale bar and actual magnification when intermetallic phases are not detected. Partial mention of 400x magnificat...

Open

8499

4.4.2

AI

No

add date

No information is provided regarding the presence, reporting, or acceptance criteria for centerline intermetallic stringers based on CVN and corrosion test results. Relevant documents do not address this requirement. Source: DMV_STANDARD_BOOK/12-03-0...

Open

8500

4.4.2

AI

No

add date

NORSOK MDS D41 and D51 allow isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not meet the stricter requirement that no intermetallic phases and/or precipitates are permitted if CVN testing cannot ...

Open

8501

4.4.3

AI

No

add date

No information is provided confirming ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781; only grain size measurement is discussed, not ferrite content determination. Source: DMV_STANDARD_BOOK/12 - Special Testing/...

Open

8502

4.4.3

AI

No

add date

No acceptance criteria or results for micrographic examination are provided, and grain size examination is not applicable to super-duplex stainless steels like DMV 25.7N. Requirement not fulfilled for this material or based on available documentation...

Open

8503

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8504

4.5

AI

No

add date

No acceptance criteria for metallurgical properties are specified for DMV 25.7N in the provided documents. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

8505

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

8506

5.1

AI

No

add date

No evidence provided regarding qualification or certification of NDE personnel to ISO 9712 level II or III, or their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDARD_BOOK/...

Open

8507

5.2

AI

No

add date

No confirmation of 100% ultrasonic testing per ASTM E213 or ISO 10893-10 after all processing, nor details on reference notches or compliance with calibration requirements are provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destr...

Open

8508

5.2

AI

No

add date

Dye penetrant testing is offered for tube ends and bevels on request, matching standard practice and client inquiry requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-05 - Dye penetrant testing/12-02-05...

Open

8509

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor that this acceptance criterion is applied in the Montbard plant for the request...

Open

8510

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

8511

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N meets the chemical composition requirements of Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

8512

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for the specified product are confirmed to be per the applicable ASTM standard (including ASTM A 790 with A 999 for tolerances), with no deviations or special requirements indicated for TechnipFMC. Requi...

Open

8513

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and white pickled or bright annealed per NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: Digest ASTM A 7...

Open

8514

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

8515

10.0

AI

No

add date

No information is provided confirming the manufacturer's quality-assurance system (such as ISO 9001 certification by a competent EEA body) or its specific assessment for materials. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDA...

Open

8516

10.1

AI

No

add date

No evidence provided that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-03...

Open

8517

10.1

AI

No

add date

Certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

8518

10.2

AI

No

add date

No provided document confirms that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC as specified in the requirement. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-02 - ...

Open

8519

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control for mill inspection, which implies compliance with ASTM A790 and NORSOK M-630 information requirements as per standard industry practice. Source: 14-03 -...

Open

8520

10.2

AI

No

add date

No provided document contains the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or test results. General pr...

Open

8521

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured and tested in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, including all relevant mechanical, chemical, and testing requirements. Source: DMV_STANDARD_BOOK...

Open

8522

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of QTR/MPCR availability for review by TechnipFMC as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest ...

Open

8523

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N up to the required wall thickness, and the manufacturing process is qualified according to M-650 and meets NORSOK M-630 MDS D51 Rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

8524

3.1

AI

No

add date

DMV 25.7N (UNS S32760) is manufactured according to NORSOK M-650 qualified procedures, with MST-Tubes F accredited for UNS S32760/DMV25.7N up to WT = 31.75 mm, covering the requested WT of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

8525

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed in accordance with ASTM A790, with manufacturing process qualified to NORSOK M-650, fulfilling requirements for furnace compliance and free circulation of media during h...

Open

8526

4.1

AI

No

add date

There is no confirmation that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790. Testing frequency, lot definition, and full scope of req...

Open

8527

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

8528

4.1

AI

No

add date

Test sampling requirements for tensile (direction per ASTM A790), CVN (transverse or longitudinal), and specific sampling locations (outer surface, 1/2 thickness, full thickness) are not fully addressed; information on CVN, corrosion, and microstruct...

Open

8529

4.2

AI

No

add date

Tensile and hardness testing are performed per lot in accordance with ASTM A370, meeting or exceeding the tensile and maximum hardness properties of Table 4 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

8530

4.2

AI

No

add date

None of the provided documents confirm that the mechanical requirements (tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, hardness max 310/300 HBW) are fulfilled for DMV 25.7N. Referenced standards either do not specify these v...

Open

8531

4.3

AI

No

add date

No evidence that Charpy V-notch testing will be performed, that it will follow ASTM A370, ASTM A1058, or ISO 148-1 with 8 mm striker radius, or that results will meet Table 5; only feasibility is confirmed for the ordered pipe size and standards, not...

Open

8532

4.3

AI

No

add date

Impact testing at -466C with specified absorbed energy values is feasible and can be fulfilled for pipe with 18.26mm wall thickness, as both ASTM and ISO rules confirm transverse specimens are possible for this size. Source: DMV_STANDARD_BOOK/12 - S...

Open

8533

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination according to ISO 17781 or specification of the required etchant solution for 25 Cr Duplex stainless steels; only grain size measurement for austenitic materials is addressed, not duplex grades...

Open

8534

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination of ferrite balance and intermetallic phases in the provided documentation. Source: DMV_STANDARD_BOOK/12 - Special ...

Open

8535

4.4.2

AI

No

add date

The microstructure must be basically free from intermetallic precipitates, with isolated precipitates allowed if not distributed throughout the specimen and each phase is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - S...

Open

8536

4.4.2

AI

No

add date

No information is provided regarding the detection, recording, or micrographic documentation (at 400x or higher) of intermetallic phases; the requirement is not addressed or fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructiv...

Open

8537

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790, NORSOK MDS S01.

Open

8538

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at 400x minimum magnification with a scale bar when intermetallic phases are not detected; relevant documents do not confirm fulfillment of all specif...

Open

8539

4.4.2

AI

No

add date

No relevant documentation addresses the reporting or acceptance criteria for centerline intermetallic stringers or links acceptance to CVN and corrosion test results if such stringers are present. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Exami...

Open

8540

4.4.2

AI

No

add date

Standards NORSOK MDS D41 and D51 allow isolated intermetallic precipitates below 10µm even if CVN testing cannot be completed, which does not fully prohibit intermetallic phases/precipitates as required. Other referenced documents do not address the ...

Open

8541

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided or addressed in the relevant documents or comments. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 ...

Open

8542

4.4.3

AI

No

add date

No provided documents address acceptance criteria or results for micrographic examination or metallurgical properties relevant to DMV 25.7N; grain size examination procedures are not applicable to duplex/super-duplex steels and are not referenced for...

Open

8543

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and confirmed for DMV 25.7N in the referenced documents. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev ...

Open

8544

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided; only 'A790 NORSOK' is referenced, which does not confirm fulfillment of this requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tes...

Open

8545

4.5

AI

No

add date

No explicit acceptance criteria for metallurgical properties are specified in the provided documents, making validation impossible with the given information. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - D...

Open

8546

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria: no pitting at 20X magnification and weight loss < 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

8547

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDA...

Open

8548

5.2

AI

No

add date

No evidence that 100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10, including reference notches as specified, will be performed after all processing steps. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destru...

Open

8549

5.2

AI

No

add date

100% qualitative anti-mixing PMI check is performed on standard production at Montbard using appropriate instruments, fulfilling general NDE acceptance criteria for PMI. Source: DMV_STANDARD_BOOK/12-06-06 - Positive Material Identification (PMI) in M...

Open

8550

5.2

AI

No

add date

No provided document confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair; acceptance/rejection criteria and disposition policy are not explicitly addressed for NDE indications relative ...

Open

8551

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed as per the applicable ASTM standards (including ASTM A 790 with A 999 for tolerances) for both hot and cold finished products, with no overriding TechnipFMC requirements indicated for the r...

Open

8552

9.0

AI

No

add date

Weld repairs are explicitly stated as not acceptable for MST-Tubes per the specification section on surface finish repairs of defects. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

8553

10.0

AI

No

add date

No evidence of an ISO 9001 or equivalent quality-assurance system certified by a competent EEA body is provided for the material manufacturer or Montbard plant. No certification details or confirmation are present in the referenced documents or excer...

Open

8554

10.1

AI

No

add date

No evidence that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-03 - Certif...

Open

8555

10.1

AI

No

add date

Certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

8556

10.2

AI

No

add date

No provided document confirms that documentation traceable to the products and transmitted to TechnipFMC (such as SIR205) will be provided as required. No explicit evidence of compliance with the traceability and transmission requirement is present. ...

Open

8557

10.2

AI

No

add date

A Mill Inspection Certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control; standard practice implies inclusion of ASTM A790 and NORSOK M-630 information when required by the order specification. Source: 14-03 - Certifica...

Open

8558

10.2

AI

No

add date

None of the provided documents contain the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or test results. O...

Open

8559

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are manufactured and tested in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, including all relevant mechanical, chemical, and testing requirements. Source: DMV_...

Open

8560

1.0

AI

No

add date

No evidence that the supplier is qualified to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of the availability of the full Qualification Test Record/MPCR for review by TechnipFMC as required by the specification. S...

Open

8561

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm for hot finished, 10.925 mm for cold finished), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 requirements w...

Open

8562

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N complies with the required chemical analysis in Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

8563

3.1

AI

No

add date

DMV 25.7N (UNS S32760) is manufactured according to NORSOK M-650 qualified procedures, with MST-Tubes F accredited for UNS S32760/DMV25.7N up to WT = 31.75 mm, covering the requested WT of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

8564

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed per ASTM A790, with manufacturing process and furnaces qualified according to NORSOK M-650 or ISO 17782, ensuring compliance with requirements for free circulation of he...

Open

8565

4.1

AI

No

add date

There is no evidence that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is carried out for each heat and heat treatment lot as defined in ASTM A790. Testing frequency, lot definition, and required test types...

Open

8566

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

8567

4.1

AI

No

add date

Test sampling details such as test direction (longitudinal or transverse per ASTM A790), CVN impact testing, and specific thickness locations are not fully specified in the provided documents. Requirements for CVN and hardness tests are also not addr...

Open

8568

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature in accordance with ASTM A370 or ISO 6892-1, meeting the tensile and maximum hardness properties of Table 4. Hardness results are provided in HRC as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

8569

4.2

AI

No

add date

None of the provided documents confirm that DMV 25.7N meets the specified mechanical requirements for tensile strength, yield strength, elongation, or hardness. The referenced standards either do not list the required values or address different grad...

Open

8570

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, meeting the minimum wall thickness requirements for both standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testi...

Open

8571

4.3

AI

No

add date

Pipe dimensions allow for both transverse and longitudinal Charpy V-notch impact specimens, and impact testing at -46°C with the specified absorbed energy values is feasible and can be fulfilled for this product. Source: DMV_STANDARD_BOOK/12-03-02 - ...

Open

8572

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination according to ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels is provided. No relevant information for duplex grades or required etching is present in the review...

Open

8573

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination of ferrite balance and intermetallic phases in the provided documents. Source: DMV_STANDARD_BOOK/12 - Special Test...

Open

8574

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

8575

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided or addressed in the relevant documentation or comments. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/1...

Open

8576

4.4.2

AI

No

add date

If intermetallic phases are not detected, a representative micrograph at minimum 400x magnification at or near mid-wall thickness is recorded, reported at actual magnification, and includes a scale bar. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

8577

4.4.2

AI

No

add date

No relevant documents address the reporting of centerline intermetallic stringers or acceptance criteria based on CVN and corrosion test results if such stringers are present. Requirement not fulfilled.

Open

8578

4.4.2

AI

No

add date

The referenced NORSOK digests allow isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geo...

Open

8579

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided; only grain size measurement is discussed, which is not relevant to the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-0...

Open

8580

4.4.3

AI

No

add date

No provided document specifies acceptance criteria for micrographic examination or required metallurgical properties for DMV 25.7N; relevant sections are not addressed or only describe procedures without criteria or results. Source: DMV_STANDARD_BOOK...

Open

8581

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8582

4.5

AI

No

add date

No explicit acceptance criteria for metallurgical properties are specified; referenced documents provide general information but do not detail the required acceptance values or criteria for validation of this requirement. Source: DMV_STANDARD_BOOK/02...

Open

8583

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria: no pitting at 20X magnification and weight loss < 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

8584

5.1

AI

No

add date

No provided documents contain information on the qualification or certification of NDE personnel to ISO 9712 level II or III, or their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, ...

Open

8585

5.2

AI

No

add date

No evidence is provided that 100% ultrasonic testing per ASTM E213 or ISO 10893-10, performed after all processing steps and with the specified calibration notches, is fulfilled at Montbard. Dimensional feasibility is given, but not compliance with a...

Open

8586

5.2

AI

No

add date

Dye penetrant testing is performed on tube ends and bevels on request, and 100% qualitative anti-mixing PMI is conducted on standard production, fulfilling the NDE requirement as specified by the client inquiry and standard practice. Source: DMV_STAN...

Open

8587

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch will result in rejection or repair of pipe and tubing as required; NDE acceptance criteria are not directly stated or confirmed for the s...

Open

8588

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed as per the applicable ASTM standards (including ASTM A 790 with reference to A 999) for both hot and cold finished products, with no deviations or overriding specifications indicated for th...

Open

8589

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed (ASTM A790) and white pickled or bright annealed (NORSOK MDS S01), directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790, NORSOK MDS S01.

Open

8590

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical analysis for DMV 25.7N complies with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

8591

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations. For the ordered ...

Open

8592

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

8593

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required for MST-Tubes in the specification digest under NORSOK MDS S01 Rev 05. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

8594

10.0

AI

No

add date

No evidence of an ISO 9001 or equivalent quality-assurance system certified by a competent EEA body is provided for the material manufacturer or Montbard plant. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Cert...

Open

8595

10.1

AI

No

add date

No evidence provided that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-03...

Open

8596

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

8597

10.2

AI

No

add date

No evidence that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205. Certification and inspection documents are described, but transmission and traceability to TechnipFMC are not confirmed. Source: DMV_STA...

Open

8598

10.2

AI

No

add date

Material certificate is issued according to EN 10204 Type 3.1 and validated by Quality Control; standard practice includes information required by ASTM A790 and NORSOK M-630. Source: 14-03 - Certification Montbard plant.doc

Open

8599

10.2

AI

No

add date

No provided documents contain the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or test results for the spe...

Open

8600

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

8601

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of full qualification to both NORSOK M-650/ISO 17782 or availability of QTR/MPCR as required by the specification. Source: DMV_ST...

Open

8602

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, with qualification testing meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_S...

Open

8603

3.1

AI

No

add date

AOD or equivalent refining is used 100% for DMV 25.7N, and chemical analysis complies with Table 2 requirements for the grade. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8604

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits, including PRE ≥ 40, as required by ASTM A790 and NORSOK MDS D51 Rev 06. Chemical limits in the requirement table are matched and confirmed for compliance. Source: 02-03-0...

Open

8605

3.2

AI

No

add date

Pipes are solution annealed followed by water quenching per ASTM A790, with furnaces and heat treatment process qualified and compliant with NORSOK M-650/ISO 17782, ensuring free circulation of heating and cooling media during treatment. Source: DMV_...

Open

8606

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

8607

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

8608

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness l...

Open

8609

4.2

AI

No

add date

Tensile testing is performed at room temperature per NORSOK MDS D51 Rev 06, referencing ASTM A370 and ISO 6892-1, with specified tensile and maximum hardness properties met for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

8610

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets or exceeds the required minimum tensile strength (750 MPa), yield strength (550 MPa), elongation (25%), and maximum hardness (310 HBW) per NORSOK MDS D51 Rev 6 and ASTM A790 for S32760. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

8611

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness (>6mm), fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - ...

Open

8612

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; the specified pipe dimensions allow for required transverse testi...

Open

8613

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

8614

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is required as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NO...

Open

8615

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

8616

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

8617

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

8618

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

8619

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates below 10μm, which does not meet the stricter client requirement of no interm...

Open

8620

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

8621

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requirement for DMV 25....

Open

8622

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8623

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or documented. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

8624

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties, including destructive, corrosion, micrographic tests, and ferrite content, as required by NORSOK MDS D51 Rev 06, ASTM A790, and NORSOK M-650/ISO 17782 for the specified wall thickn...

Open

8625

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

8626

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

8627

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

8628

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51 Rev 6/NORSOK M-650/ISO 17782 are not fully addressed. For the requested OD (219.1 mm), Eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at extra c...

Open

8629

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair, and standard NDE methods are not feasible for the specified OD at Montbard, so the requirement is no...

Open

8630

6.0

AI

No

add date

Dimensional tolerances are confirmed as per the applicable ASTM standard (ASTM A999 referenced by ASTM A790) for the requested pipe dimensions, with no overriding requirements from TechnipFMC specified in the inquiry context. Source: DMV_STANDARD_BOO...

Open

8631

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

8632

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring compliance with the requirement. Source: DM...

Open

8633

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

8634

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

8635

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

8636

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

8637

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

8638

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

8639

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

8640

10.2

AI

No

add date

No provided documentation includes all required items: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, ladle analysis, solution annealing details, or actual metallurgical and non-destructive te...

Open

8641

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with all relevant mechanical, chemical, and testing requirements fulfilled. Source: 02-03-01 - Digest ASTM ...

Open

8642

1.0

AI

No

add date

No document confirms supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor the availability of the full Qualification Test Record/MPCR for review as required. One document confirms NORSOK M-650 accreditation fo...

Open

8643

3.0

AI

No

add date

MST-Tubes F is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and qualification testing meets NORSOK M-630 MDS D51 Rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

8644

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N meets the required chemical composition per Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

8645

3.1

AI

No

add date

DMV 25.7N (UNS S32760) is manufactured according to NORSOK M-650 qualified procedures, with accreditation covering the requested wall thickness of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-0...

Open

8646

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed per ASTM A790, with manufacturing process and furnaces qualified according to NORSOK M-650 or ISO 17782, ensuring compliance with requirements for free circulation of he...

Open

8647

4.1

AI

No

add date

There is no evidence that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is carried out for each heat and heat treatment lot as defined in ASTM A790; required testing frequency and lot definition are not conf...

Open

8648

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no evidence of CVN (Charpy) impact testing, required test directions, or specified thickness locations for all tests as per the requirement. Hardness and corrosion/microstructure test sampling ...

Open

8649

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-...

Open

8650

4.2

AI

No

add date

Mechanical property values for DMV 25.7N (UNS S32760/S32750) are not explicitly confirmed; tensile strength, yield strength, elongation, and hardness requirements cannot be validated with the provided information. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

8651

4.3

AI

No

add date

No evidence that Charpy V-notch testing is performed or that results meet the requirements of ASTM A370, ASTM A1058, ISO 148-1, or Table 5, despite feasibility for testing with the specified wall thickness. Source: DMV_STANDARD_BOOK/02-02-01 Digest s...

Open

8652

4.3

AI

No

add date

Pipe dimensions allow for both longitudinal and transverse Charpy V-notch impact specimens; impact testing at the specified temperature and energy levels is feasible and can be fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destruc...

Open

8653

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination per ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels. Grain size examination is only discussed for austenitic materials, not duplex steels....

Open

8654

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination of duplex/super-duplex steels; required etching and standard not mentioned or addressed for DMV 25.7N grade. Sourc...

Open

8655

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic phases; isolated phases are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06...

Open

8656

4.4.2

AI

No

add date

No information or documentation is provided regarding the presence, location, or micrographic recording (400x minimum) of intermetallic phases as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Microgra...

Open

8657

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at actual magnification (400x minimum) with a scale bar if intermetallic phases are not detected. Requirements for actual magnification and scale bar ...

Open

8658

4.4.2

AI

No

add date

No relevant documents mention the detection, reporting, or acceptance criteria for centerline intermetallic stringers, nor their relation to CVN or corrosion test results. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I.doc, DMV_...

Open

8659

4.4.2

AI

No

add date

Referenced documents allow isolated intermetallic precipitates below 10µm and do not fully prohibit intermetallic phases/precipitates when CVN testing cannot be completed, which does not meet the client's zero-tolerance requirement in such cases. No ...

Open

8660

4.4.3

AI

No

add date

No information is provided regarding ferrite content measurement or compliance with ASTM E 562, ASTM E 1245, or ISO 17781 for micrographic examination of ferrite content in the available documentation or comments. Source: DMV_STANDARD_BOOK/12 - Speci...

Open

8661

4.4.3

AI

No

add date

No acceptance criteria for micrographic examination or metallurgical properties are specified or addressed in the provided sources for DMV 25.7N or the specific order. Requirement not fulfilled by the given information. Source: DMV_STANDARD_BOOK/02-0...

Open

8662

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8663

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided; only A790 NORSOK is referenced, which does not explicitly cover the required test. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in M...

Open

8664

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are provided; only section headings or general references are present without actual values or limits for validation. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDA...

Open

8665

4.5

AI

No

add date

Specification requires pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², matching the client's requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

8666

5.1

AI

No

add date

No provided documents contain information on the qualification or certification of NDE personnel to ISO 9712 level II or III, nor on their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-...

Open

8667

5.2

AI

No

add date

No explicit confirmation of 100% ultrasonic testing per ASTM E213 or ISO 10893-10, calibration notches, or testing after all processing steps is provided. Only dimensional feasibility for ultrasonic testing is mentioned, not fulfillment of the requir...

Open

8668

5.2

AI

No

add date

100% qualitative anti-mixing PMI check is performed on standard production at Montbard using appropriate instruments, fulfilling general NDE acceptance criteria for PMI. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/1...

Open

8669

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, as specified in the requirement. NDE feasibility and referenced standards do not st...

Open

8670

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for the specified product are confirmed as per the applicable ASTM standards (including ASTM A790/A999) for the relevant size range, with no overriding TechnipFMC part report or drawing specified. Requir...

Open

8671

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed per ASTM A790 and NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790 digest, NORSOK MDS S01 Rev 05.

Open

8672

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13 - Marking/13-02 - Standard marking feasibility/13-02-01 - Standard marking feasibility - Montbard plant/13...

Open

8673

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 specifies that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

8674

10.0

AI

No

add date

No evidence is provided of an ISO 9001 certified quality-assurance system or certification by a competent EEA body with a specific assessment for materials for the material manufacturer at the Montbard plant. Source: DMV_STANDARD_BOOK/14-01 - General...

Open

8675

10.1

AI

No

add date

No confirmation that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body with specific assessment for materials as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 ...

Open

8676

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demonst...

Open

8677

10.2

AI

No

add date

There is no explicit confirmation that the required documentation (traceable to the products and to be transmitted to TechnipFMC, such as SIR205) will be provided as specified in the requirement. No evidence of traceability or transmission to Technip...

Open

8678

10.2

AI

No

add date

A Mill Inspection Certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control, with reference to ASTM A790 and NORSOK M-630 in the customer specifications and quality system. Source: 14-03 - Certification Montbard plant.doc

Open

8679

10.2

AI

No

add date

No provided document contains the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or test results for metallu...

Open

8680

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all referenced mechanical, chemical, and testing requirements. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_...

Open

8681

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782, as required. No evidence of QTR/MPCR availability is provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8682

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

8683

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard and required, and chemical analysis complies with Table 2 for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8684

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements, and heat analysis is performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A...

Open

8685

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650 or ISO 17782, and pipes arranged to ensure proper heat treatment circulation. Sou...

Open

8686

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for each heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

8687

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

8688

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse, feasible for 18.26 mm WT), and corrosion/microstructure tests at specified thicknes...

Open

8689

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

8690

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

8691

4.3

AI

No

add date

Pipe dimensions exceed minimum wall thickness required for Charpy V-notch testing as per ASTM A370, ASTM A1058, or ISO 148-1; testing is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products...

Open

8692

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C (transverse: 45 J avg/35 J single, longitudinal: 65 J avg/50 J single if transverse not possible). The specified pipe dimensions allow for required transverse Charpy ...

Open

8693

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with etching for intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

8694

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

8695

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

8696

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

8697

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

8698

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

8699

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10μm, but the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Zero-tolerance is not guaranteed in the referenced documents. Source: DMV...

Open

8700

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

8701

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

8702

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

8703

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

8704

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified per NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

8705

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

8706

4.4.1

AI

No

add date

No evidence of etching with 20-40% NaOH or KOH solution or other suitable etchant as per ISO 17781 Appendix B for micrographic examination of ferrite balance and intermetallic phases is provided.

Open

8707

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

8708

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic ...

Open

8709

5.2

AI

No

add date

NDE methods (EC, UT, hydrostatic) for the required OD are either not feasible, only available at extra cost, or not confirmed as standard at the Montbard plant. There is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782 N...

Open

8710

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair of pipe/tubing as specified by the requirement. NDE acceptance criteria based on cal...

Open

8711

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790/A999) for the specified pipe dimensions, with no evidence of overriding requirements from TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DM...

Open

8712

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

8713

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

8714

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8715

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

8716

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

8717

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demonstration for th...

Open

8718

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceable documentation as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03...

Open

8719

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications and documentation scope. Source: DMV_STANDARD_BOOK/02-04-03 - Dig...

Open

8720

10.2

AI

No

add date

EN 10204 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. No evidence of actua...

Open

8721

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with all relevant mechanical, chemical, and testing requirements met for the specified grade and standards. Source: 02-03-01 - Digest ASTM A ...

Open

8722

1.0

AI

No

add date

No evidence of supplier qualification to NORSOK M-650/ISO 17782 for the exact product supplied or availability of the full Qualification Test Record/MPCR for review by TechnipFMC. MST-Tubes is only M-650 accredited (not ISO 17782), and other document...

Open

8723

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm for hot finished, 10.925 mm for cold finished), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 require...

Open

8724

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes and DMV 25.7N complies with the required chemical analysis. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORS...

Open

8725

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the inquiry's WT is 18.26 mm, fulfilling the requirement for manufacturing process qualification per NORSOK M-650 or ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

8726

3.2

AI

No

add date

Pipes are solution annealed and water quenched per ASTM A790, with furnaces and process qualified to NORSOK M-650/ISO 17782, and free circulation of heating/cooling media ensured by compliance with these standards. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

8727

4.1

AI

No

add date

There is no explicit confirmation that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is carried out for each heat and heat treatment lot as defined in ASTM A790. Some tests are mentioned but not all, and req...

Open

8728

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

8729

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no evidence of CVN impact testing or its required test direction, nor are detailed sampling locations and methods per Table 3 addressed. Requirement not fully fulfilled due to missing informati...

Open

8730

4.2

AI

No

add date

Tensile testing is performed per ASTM A370, and the material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

8731

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required are not confirmed or are not met by the referenced documents; properties for TP316/316L do not fulfill the higher requirements for DMV 25.7N (UNS S32760). So...

Open

8732

4.3

AI

No

add date

No evidence that Charpy V-notch testing is performed or that results meet Table 5 requirements; only feasibility is confirmed for the specified dimensions, not actual compliance or testing per ASTM A370, ASTM A1058, or ISO 148-1 with 8 mm striker rad...

Open

8733

4.3

AI

No

add date

Pipe wall thickness of 18.26mm allows both longitudinal and transverse Charpy V-notch impact tests at -46°C, meeting the specified absorbed energy requirements for pipes >6mm thick. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished pr...

Open

8734

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination according to ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels is provided. Grain size examination is only discussed for austenitic materials, not duplex steels. ...

Open

8735

4.4.2

AI

No

add date

Micrographic examination requires the microstructure to be basically free from intermetallic precipitates, allowing isolated precipitates if not distributed throughout the specimen and each is below 10µm, matching the client's requirement exactly. So...

Open

8736

4.4.2

AI

No

add date

No information or procedures are provided regarding the detection, recording, or micrographic documentation of intermetallic phases at 400x or higher magnification as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testin...

Open

8737

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at 400x minimum magnification with actual magnification and scale bar when intermetallic phases are not detected. Partial mention of 400x photos, but ...

Open

8738

4.4.2

AI

No

add date

No relevant documentation addresses the reporting of centerline intermetallic stringers or acceptance based on CVN and corrosion test results if such stringers are present. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I.doc, DMV...

Open

8739

4.4.2

AI

No

add date

Referenced specifications allow isolated intermetallic precipitates below 10μm and do not fully prohibit intermetallic phases/precipitates if CVN testing cannot be completed, which is stricter in the client requirement demanding their complete absenc...

Open

8740

4.4.3

AI

No

add date

No information is provided regarding ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781; only grain size measurement is discussed, which is not relevant to the requirement. Source: DMV_STANDARD_BOOK/12 - Special Te...

Open

8741

4.4.3

AI

No

add date

No provided document specifies acceptance criteria for micrographic examination or metallurgical properties relevant to section 4.4; procedures and standards are mentioned, but required values or criteria are absent or not addressed for DMV 25.7N or ...

Open

8742

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8743

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781; only A790 NORSOK is referenced, which does not confirm fulfillment of this requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard...

Open

8744

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are provided or referenced; the requirement cannot be validated without explicit criteria or details. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

8745

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 25°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

8746

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDA...

Open

8747

5.2

AI

No

add date

No evidence that 100% ultrasonic testing per ASTM E213 or ISO 10893-10 is performed after all mechanical processing, heat treatment, and straightening, or that calibration notches meet Figure 3 of ASTM E213 requirements and specified dimensions and l...

Open

8748

5.2

AI

No

add date

100% qualitative anti-mixing PMI check is performed on standard production at Montbard using appropriate instruments, fulfilling the general NDE requirement for positive material identification. No stricter PMI requirement is indicated for this order...

Open

8749

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

8750

5.2

AI

No

add date

No provided document confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor are the specific acceptance criteria for NDE indications detailed for the requested product and dimension. NDE...

Open

8751

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed as per the applicable ASTM standards (including A790/A999) for both hot and cold finished products, with no deviations or special customer requirements indicated for the specified size rang...

Open

8752

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and white pickled or bright annealed per NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: Digest ASTM A 7...

Open

8753

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

8754

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

8755

10.0

AI

No

add date

No evidence is provided that the material manufacturer has an ISO 9001 or equivalent quality-assurance certification by a competent EEA body or that a specific assessment for materials has been performed. Source: DMV_STANDARD_BOOK/14-01 - General inf...

Open

8756

10.1

AI

No

add date

No evidence that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body is provided. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-03 - Cer...

Open

8757

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV25.7N up to WT = 31.75 mm (requested WT is 18.26 mm), and the EN 10204 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number. Source:...

Open

8758

10.2

AI

No

add date

No provided document confirms that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC as specified in the requirement. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-02 - ...

Open

8759

10.2

AI

No

add date

A Mill Inspection Certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control, with reference to ASTM A790 and NORSOK M-630 in the customer specification, fulfilling the requirement for certification and included information...

Open

8760

10.2

AI

No

add date

No provided document includes the required NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or results of metallurgical and non-destructive testing for the specific m...

Open

8761

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the customer requirements and confirmed by the digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_B...

Open

8762

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability or full compliance with essential variables and limitations per the specification. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

8763

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N within the required wall thickness range, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_...

Open

8764

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8765

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PREN ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8766

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

8767

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot, with 'lot' defined as per ASTM A790, fulfilling the requirement for testing per heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 -...

Open

8768

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

8769

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes per ASTM A790 and NORSOK MDS D51 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified loca...

Open

8770

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Hardness testing is also performed as specified. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

8771

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW, fulfilling all Table 4 mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

8772

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

8773

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C (transverse: avg 45 J, single 35 J; longitudinal: avg 65 J, single 50 J) for thickness 6 mm, and the specified pipe dimensions allow for required testing orientatio...

Open

8774

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with specified etchants after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

8775

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is specified and fulfills the requirement for suitable etchants as listed in ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

8776

3.1

AI

No

add date

AOD or equivalent refining is required for 100% of production, and the chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dige...

Open

8777

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

8778

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

8779

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

8780

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria based on CVN and corrosion...

Open

8781

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

8782

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

8783

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

8784

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8785

4.5

AI

No

add date

No explicit confirmation that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or included in the referenced documents. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

8786

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8787

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

8788

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destru...

Open

8789

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

8790

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD, eddy current testing is not feasible, and hydrostatic/ultrasoni...

Open

8791

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed by heat analysis with supplier certification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Dige...

Open

8792

5.2

AI

No

add date

No provided documentation explicitly confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor is there confirmation that the required NDE is feasible for the specified ...

Open

8793

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding TechnipFMC specification indicated. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according t...

Open

8794

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

8795

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 (§14), both requiring full traceability to melt and heat treatment lot. Marking methods include heat number and DMV lot number, ensuring compliance with the requirement for full traceabili...

Open

8796

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8797

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

8798

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

8799

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, and QTR number is included as per M-650 qualification, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MCPR...

Open

8800

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

8801

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 manufacturing ...

Open

8802

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or results of required metallurgical and non-destructive testing. Only...

Open

8803

1.0

AI

No

add date

DMV 25.7N seamless pipes are confirmed as fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the item table and supporting documentation. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8804

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR documentation availability as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS ...

Open

8805

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

8806

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

8807

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

8808

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

8809

4.1

AI

No

add date

Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), corrosion, and microstructure tests at specified thickness locations, are fulfilled for DMV 25....

Open

8810

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

8811

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

8812

4.3

AI

No

add date

Pipe dimensions exceed minimum wall thickness required for Charpy V-notch testing as per ASTM A370, ASTM A1058, or ISO 148-1; testing is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing...

Open

8813

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible). The specified pipe dimensions allow ...

Open

8814

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

8815

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

8816

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

8817

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

8818

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

8819

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

8820

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8821

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates, which does not meet the stricter client requirement of not permitting any i...

Open

8822

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

8823

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

8824

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50°C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

8825

4.5

AI

No

add date

All acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, microstructure, PRE, solution annealing, and ferrite content, are fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02-04-0...

Open

8826

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

8827

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

8828

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is confirmed, applicable after all mechanical processing, and the dimensional range is supported. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03...

Open

8829

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially addressed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782 NDE requirements are fulfilled. For the specified OD (219.1 mm), eddy current testing is not fe...

Open

8830

5.2

AI

No

add date

No provided documentation explicitly confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that such NDE acceptance criteria are standardly performed or feasible for the specified pipe ...

Open

8831

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790) unless otherwise specified, and no deviations are indicated in the customer specification or context. Source: DMV_STANDARD_BOOK/07-01 - General informa...

Open

8832

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8833

8.0

AI

No

add date

Marking is performed according to ASTM A790, requiring full traceability to melt and heat treatment lot, with mandatory marking of heat number and DMV lot number ensuring compliance. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

8834

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 explicitly states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NO...

Open

8835

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8836

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

8837

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

8838

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification documentation requirement for the ...

Open

8839

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

8840

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and will include all information required by ASTM A790 and NORSOK M-630; certificates are validated by Quality Control for mill inspection, fulfilling the requirement. Source: 02-04-03 - Digest NORSOK MDS D...

Open

8841

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice, refining method, heat treatment condition, heat number, chemical analysis, and test results, but only the country of origin of the steel supplie...

Open

8842

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified up to the required wall thickness...

Open

8843

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8844

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

8845

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8846

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and in accordance with ASTM A790 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat. Sourc...

Open

8847

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

8848

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

8849

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Dige...

Open

8850

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

8851

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations per NORSOK MDS D51/ASTM A790. F...

Open

8852

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-0...

Open

8853

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

8854

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfills the requirement for the specified pipe dimensions according to ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impa...

Open

8855

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements (Charpy V-notch at -466C: transverse 45J/35J, longitudinal 65J/50J, sub-size reduction factors). The specified pipe dimensions allow for both longitudinal and transverse test...

Open

8856

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

8857

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

8858

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

8859

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

8860

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

8861

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

8862

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

8863

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

8864

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and ...

Open

8865

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782 as required; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8866

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

8867

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: Digest NORSOK MDS D51 Rev 06.docx

Open

8868

4.5

AI

No

add date

DMV 25.7N meets the pitting corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours, with no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

8869

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor are their roles and responsibilities defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructiv...

Open

8870

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is confirmed for the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12...

Open

8871

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not explicitly addressed in the available documentation. Standard NDE methods (hydrostatic, ultrasonic, eddy current) for the requested OD are only available at extra cos...

Open

8872

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor is there confirmation that the required NDE acceptance criterion is feasible fo...

Open

8873

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790 referencing ASTM A999) for the requested pipe, with no overriding requirements from TechnipFMC identified in the provided context. Source: DMV_STANDARD_BOOK/07-01 ...

Open

8874

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

8875

8.0

AI

No

add date

Marking is performed per ASTM A790 §14 and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

8876

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

8877

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

8878

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers as specified in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

8879

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified ...

Open

8880

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

8881

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specification sections. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D...

Open

8882

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the spec...

Open

8883

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all specified mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified for the required wall t...

Open

8884

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORS...

Open

8885

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

8886

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8887

3.1

AI

No

add date

Chemical composition for S32760 matches Table 2 requirements and is confirmed to conform per heat analysis. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

8888

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650/ISO 17782. Pipes are treated to ensure free circulation of heating and co...

Open

8889

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

8890

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

8891

4.1

AI

No

add date

Test sampling requirements for seamless pipes per ASTM A790 and NORSOK MDS D51, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations,...

Open

8892

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with material meeting the tensile and maximum hardness properties of Table 4 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

8893

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW as specified in Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

8894

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370 and ISO 148-1 as required. Source: 12-03-02 - Impact Test for hot finished products.doc

Open

8895

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical analysis complies with Table 2 for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8896

4.3

AI

No

add date

DMV 25.7N meets the impact test requirements of NORSOK MDS D51 Rev 06 at -46°C, with minimum absorbed energy values and sub-size reduction factors as specified. The product dimensions allow for required transverse Charpy V-notch testing, ensuring ful...

Open

8897

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

8898

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is explicitly required for micrographic examination as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

8899

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

8900

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded as required. Source...

Open

8901

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

8902

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK/0...

Open

8903

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

8904

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

8905

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781 at ≥400X magnification, with acceptance criteria requiring the structure to be free from intermetallic precipitates (isolated precipitates <10µm allowed), and carbides/nitrides reported; compliance ...

Open

8906

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8907

4.5

AI

No

add date

No explicit confirmation that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or reported. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

8908

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties, including destructive, corrosion, micrographic tests, and ferrite content, as required by NORSOK MDS D51 Rev 06 and related standards. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

8909

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, meeting the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest...

Open

8910

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, or their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montba...

Open

8911

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

8912

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

8913

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. Standard NDE methods (eddy current, hydrostatic, ultrasonic) for the specified OD are not feas...

Open

8914

5.2

AI

No

add date

None of the relevant documents explicitly state that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, nor do they confirm that NDE with this acceptance criterion is performed as sta...

Open

8915

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790/A999) for the specified product, with no overriding customer specification or drawing indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STA...

Open

8916

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

8917

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 §14, requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number identification, ensuring compliance with the requirement f...

Open

8918

9.0

AI

No

add date

Weld repairs are explicitly stated as not acceptable under 'Surface finish / Repairs of defects' (§13, §14) for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

8919

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

8920

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body established within the EEA, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-...

Open

8921

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demons...

Open

8922

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability information, fulfilling the requirement for documentation traceable to delivered products and transmittal to TechnipFMC. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

8923

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing the relevant standards and manufacturing summary/QTR number. Source: DMV_STANDARD_BOOK/02-04-03...

Open

8924

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements, including Charpy V-notch testing at -46°C with specified minimum absorbed energy values and sub-size reduction factors. The pipe dimensions allow for required transverse and ...

Open

8925

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

8926

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or results of required metallurgical and non-destructive testing. Only...

Open

8927

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all referenced mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified up to the required wal...

Open

8928

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not to ISO 17782; full qualification per NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR documentation is not confirmed for review as required by the specifi...

Open

8929

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

8930

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition complies with Table 2/ASTM A790 and NORSOK MDS D51 Rev 6 for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.do...

Open

8931

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PREN ≥ 40, and matches the specified limits for all elements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8932

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and furnace qualification ensures free circulation of heating/cooling media. Source: DMV_STANDARD_BOO...

Open

8933

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, with test frequency '1 / lot', fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - S...

Open

8934

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

8935

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests, with specified locations and directions, is fulfilled for DMV 25.7N per ...

Open

8936

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the specified tensile and maximum hardness properties of Table 4 as required by NORSOK MDS D51. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

8937

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

8938

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness required by the standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testin...

Open

8939

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8940

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

8941

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and if each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

8942

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

8943

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

8944

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_ST...

Open

8945

4.4.2

AI

No

add date

NORSOK MDS D51 Rev 06 allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully fulfilled. Source: DMV_STAND...

Open

8946

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

8947

4.4.3

AI

No

add date

Microstructure examination is performed as per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Acceptance criteria: structure free from intermetallic precipitates (isolated precipitates <10µm and ...

Open

8948

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

8949

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

8950

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive, micrographic, corrosion tests, ferrite content, heat treatment, and M-650 qualification for the specified grade and wall thickness. Source: DMV_STA...

Open

8951

4.5

AI

No

add date

DMV 25.7N meets ISO 17781: G48 Method A at 50°C for 24h with no pitting at 20X magnification and weight loss < 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

8952

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

8953

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is confirmed as available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testi...

Open

8954

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782, nor confirmation of QTR/MPCR availability as required. Only M-650 accreditation is mentioned, not ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

8955

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed; standard NDE methods (EC, UT, hydrostatic) for the specified OD are only available at extra cost or require technical approval, and there ...

Open

8956

5.2

AI

No

add date

The available documents do not explicitly state that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, and standard NDE methods for this criterion are either not feasible or only ava...

Open

8957

6.0

AI

No

add date

Dimensional tolerances for the requested pipe are per ASTM A790 and its referenced standards (including ASTM A999), with no deviations or special tolerances indicated in the customer specification. Requirement is fulfilled as tolerances default to th...

Open

8958

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed per ASTM A790 and white pickled or bright annealed per NORSOK MDS D51 Rev 06, fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: Digest ASTM A 790.docx, Di...

Open

8959

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

8960

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

8961

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

8962

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers as specified in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

8963

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demonst...

Open

8964

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to products, fulfilling the requirement for documentation to be transmitted to TechnipFMC and traceable as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

8965

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

8966

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgic...

Open

8967

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the listed standards and digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02 ...

Open

8968

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

8969

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

8970

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

8971

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits and PREN requirements specified in Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 06 standards. Heat analysis and supplier certification are performed per heat as required. Sour...

Open

8972

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

8973

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

8974

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, directly referencing Table 3 for test specimen sampling as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02...

Open

8975

4.1

AI

No

add date

Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, are fulfilled for DMV 25.7N per ...

Open

8976

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with mechanical properties meeting or exceeding Table 4 requirements for NORSOK MDS D51. Hardness testing is also performed as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

8977

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC), fulfilling all specified mechanical requirements. Source: DMV_STANDARD_BOOK/02 ...

Open

8978

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

8979

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible). The specified pipe dimensions allow ...

Open

8980

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

8981

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is explicitly required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_...

Open

8982

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

8983

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN ≥ 40 as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK M...

Open

8984

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included with presence and location of intermetallic phases noted and recorded. Source: DMV_STANDA...

Open

8985

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

8986

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

8987

4.4.2

AI

No

add date

No document states a zero-tolerance policy for intermetallic phases and/or precipitates if CVN testing cannot be completed; isolated precipitates are still permitted in the referenced specifications, which does not meet the requirement for total proh...

Open

8988

4.4.3

AI

No

add date

Ferrite content is determined per ISO 17781 using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source:...

Open

8989

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

8990

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in accordance with ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

8991

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50°C, 24h) in accordance with ISO 17781 is provided; neither standard nor test is mentioned in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant...

Open

8992

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including chemical composition (PRE ≥ 40), microstructure (free from intermetallics, ferrite 35-60%), impact, corrosion, and tensile properties, are fulfilled by DMV 25.7N for...

Open

8993

4.5

AI

No

add date

Corrosion test for DMV 25.7N is performed per ISO 17781: G48 Method A at 50°C for 24 hours, with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these requirements. Source: DMV_ST...

Open

8994

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

8995

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects is performed in accordance with ASTM E213 or ISO 10893-10 for the required pipe dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 ...

Open

8996

5.2

AI

No

add date

NDE per NORSOK M-630 MDS D51/ASTM A790 is required, but available documentation only covers NDE per ASTM A790/A999, not NORSOK-specific criteria. For the specified OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/ultrasonic tests ...

Open

8997

5.2

AI

No

add date

None of the relevant documents explicitly state that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, and standard NDE methods are not feasible for the requested OD at Montbard as s...

Open

8998

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the specified pipe, with no deviations or special tolerances stated in the customer specification or part report/drawing. Source: DMV_STANDARD_BOOK/07-01 - General infor...

Open

8999

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9000

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

9001

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03...

Open

9002

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

9003

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

9004

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demonst...

Open

9005

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to products, fulfilling the requirement for documentation to be transmitted to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

9006

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference). ...

Open

9007

10.2

AI

No

add date

EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MPCR number, steel melting practice, refining method, heat treatment condition, heat number, chemical analysis, and test results, but only the c...

Open

9008

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

9009

1.0

AI

No

add date

Supplier is NORSOK M-650 accredited for UNS S32760 / DMV25.7N but not accredited to ISO 17782, as required. No evidence provided for QTR/MPCR availability for review or full compliance with both standards for the exact product supplied. Source: DMV_S...

Open

9010

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), covering the required grade and wall thickness, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requir...

Open

9011

3.1

AI

No

add date

AOD or equivalent refining is standard practice and required for 100% of production; DMV 25.7N complies with the specified chemical analysis requirements. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9012

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

9013

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

9014

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, directly referencing the table for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detai...

Open

9015

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions, is fulfilled for DMV 25.7N per NOR...

Open

9016

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

9017

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

9018

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for 18.26mm wall thickness and 219.1mm OD pipe as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

9019

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact test requirements: Charpy V-notch at -46°C, minimum average 45 J and single 35 J (transverse), 65 J/50 J (longitudinal if transverse not possible), with reduction factors for sub-size specimens. Th...

Open

9020

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed according to ISO 17781 with 20-40% NaOH or KOH solution after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

9021

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is explicitly required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_...

Open

9022

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

9023

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

9024

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

9025

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

9026

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size; thus, the requirement is not...

Open

9027

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

9028

4.4.3

AI

No

add date

Microstructure examination is performed as per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Acceptance criteria require the structure to be basically free from intermetallic precipitates, with ...

Open

9029

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9030

4.5

AI

No

add date

No explicit confirmation or evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or planned. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9031

4.5

AI

No

add date

DMV 25.7N complies with all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

9032

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these requirements. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

9033

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destruct...

Open

9034

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is confirmed for the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12...

Open

9035

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/NORSOK M-650 are not fully addressed. Provided sources confirm general NDE (hydrostatic, EC, UT) per ASTM A999/A790, but do not confirm compliance with NORSOK-specific NDE requirements or...

Open

9036

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor confirms that the required NDE with this acceptance criterion will be performed...

Open

9037

6.0

AI

No

add date

Dimensional tolerances for the specified pipe are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790), with no overriding TechnipFMC specification indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_...

Open

9038

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9039

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790, requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring traceability as required by the specification. Sourc...

Open

9040

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

9041

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

9042

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demonst...

Open

9043

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

9044

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

9045

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or complete metallurgical and non-dest...

Open

9046

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured and tested in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with all relevant mechanical, chemical, and testing requirements met. Source: DMV_STANDARD_BOOK/...

Open

9047

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of QTR/MPCR availability for review by TechnipFMC as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest ...

Open

9048

3.0

AI

No

add date

MST-Tubes F is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, with manufacturing process qualified per NORSOK M-650 (or ISO 17782) and meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

9049

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N complies with the required chemical analysis per Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

9050

3.1

AI

No

add date

MST-Tubes is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the inquiry's WT of 18.26 mm, fulfilling the manufacturing process qualification requirement per NORSOK M-650 and M-630 MDS D51 rev. 6. Source: DMV_STANDARD_BOOK/02...

Open

9051

3.2

AI

No

add date

Solution annealing followed by water quenching is standard for DMV 25.7N as per ASTM A790, with manufacturing and heat treatment processes qualified and performed in compliance with NORSOK M-650/ISO 17782, including requirements for free circulation ...

Open

9052

4.4.2

AI

No

add date

No provided documents address the reporting or acceptance criteria for centerline intermetallic stringers, nor do they link CVN or corrosion test results to their presence. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I.doc, DMV...

Open

9053

4.4.2

AI

No

add date

Referenced specifications allow isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not meet the stricter requirement that intermetallic phases and/or precipitates are not permitted at all if CVN test...

Open

9054

4.1

AI

No

add date

There is no explicit evidence that impact, tensile, hardness, corrosion testing, and microstructure examinations are performed for each heat and heat treatment lot as defined in ASTM A790. Testing frequency and lot definition are not confirmed for al...

Open

9055

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

9056

4.1

AI

No

add date

Test sampling details such as test direction, CVN impact testing, and thickness location are not fully specified or confirmed for all required tests (tensile, hardness, CVN, corrosion, microstructure) on prolongation samples as per the requirement. S...

Open

9057

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature with criteria meeting or exceeding Table 4 (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%), and maximum hardness is addressed. NORSOK MDS D51 refers to ASTM A790, which requires tensile testing per AS...

Open

9058

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required for DMV 25.7N are not confirmed in the provided sources; referenced values are either missing or for a different grade with lower properties. Source: DMV_STA...

Open

9059

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and wall thickness, meeting ASTM A370 and ISO 148-1 requirements for both longitudinal and transverse directions. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished p...

Open

9060

4.3

AI

No

add date

Pipe wall thickness of 18.26 mm allows for transverse Charpy specimens, so impact property requirements at -46°C are met for both transverse and longitudinal directions as specified. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive ...

Open

9061

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination per ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels. Grain size examination procedures for duplex grades are not addressed or are stated a...

Open

9062

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination of ferrite balance and intermetallic phases is provided or addressed in the reviewed documents or comments. Source...

Open

9063

4.4.2

AI

No

add date

Micrographic examination requires the microstructure to be basically free from intermetallic phases, allowing isolated phases if not homogeneously distributed and each below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

9064

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided or addressed in the relevant documentation or comments. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/1...

Open

9065

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at 400x minimum magnification with a scale bar and actual magnification if intermetallic phases are not detected, as required by the specification. So...

Open

9066

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided or addressed. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Micrographic Examination/12-03-03 - ...

Open

9067

4.4.3

AI

No

add date

No acceptance criteria or results for micrographic examination are provided or applicable for DMV 25.7N (super-duplex stainless steel); grain size examination is not required for this material type and is not addressed in the referenced documents or ...

Open

9068

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9069

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are provided in the referenced documents, so fulfillment cannot be validated. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS S01...

Open

9070

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria: no pitting at 20X magnification and weight loss < 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

9071

5.1

AI

No

add date

No provided documents contain information about the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/...

Open

9072

5.2

AI

No

add date

No explicit confirmation of 100% ultrasonic testing per ASTM E213 or ISO 10893-10 after all processing steps, nor details on reference notches as specified. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ult...

Open

9073

5.2

AI

No

add date

100% qualitative anti-mixing PMI check is performed on standard production at Montbard using appropriate instruments, fulfilling the general NDE requirement for PMI. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02...

Open

9074

5.2

AI

No

add date

No provided document confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair; NDE acceptance criteria matching the requirement are not explicitly stated or confirmed for the specified dimen...

Open

9075

6.0

AI

No

add date

Dimensional tolerances for OD and WT are confirmed as per the applicable ASTM standards (A790/A999, A213, A268, A269, A312, A376, A511) for the relevant product dimensions, fulfilling the requirement unless otherwise specified by TechnipFMC documenta...

Open

9076

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed per ASTM A790 and 100% white pickled or bright annealed per NORSOK MDS S01, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS S01 Rev 05 .docx

Open

9077

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/13 - Marking/13-02 - Standard marking feasibility/13-02-01 - Standard marking feasibility - Montb...

Open

9078

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

9079

10.0

AI

No

add date

No evidence of an ISO 9001 quality-assurance system or certification by a competent EEA body is provided for the Montbard plant or manufacturer. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Certification Montba...

Open

9080

10.1

AI

No

add date

No evidence provided that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-03...

Open

9081

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for UNS S32760/DMV25.7N up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

9082

10.2

AI

No

add date

No evidence that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC; documents only describe certificate types and authorities without confirming compliance with the transmission and traceability requirem...

Open

9083

10.2

AI

No

add date

Mill Inspection Certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control, and compliance with customer specifications (A790 NORSOK) is implied for these grades and standards. Source: 14-03 - Certification Montbard plant.d...

Open

9084

10.2

AI

No

add date

None of the provided documents contain the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, o...

Open

9085

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all standard, supplementary, and testing requirements, and are M-650 qualified for the specified wall thickness. Source: DMV_STANDARD_BOOK/02-03-01...

Open

9086

1.0

AI

No

add date

No evidence is provided that the supplier is qualified according to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor is there confirmation of the availability of Qualification Test Records (QTR/MPCR) as required by the specificatio...

Open

9087

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

9088

3.1

AI

No

add date

AOD or equivalent refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9089

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN ≥ 40, matching the requirements of Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat as required. Source: 02-03-0...

Open

9090

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

9091

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

9092

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

9093

4.1

AI

No

add date

Test sampling for seamless pipes per ASTM A790/NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, longitudinal if not possible), and corrosion/microstructure tests are all feasible and performed as specified...

Open

9094

4.2

AI

No

add date

Tensile testing is performed at room temperature per NORSOK MDS D51 Table 4, meeting the required mechanical properties, and testing is conducted per ASTM A370 or ISO 6892-1. Hardness testing is also performed as required. Source: DMV_STANDARD_BOOK/0...

Open

9095

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

9096

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions (OD 219.1 mm, WT 18.26 mm), which exceed the minimum required wall thickness for testing. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructi...

Open

9097

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energy values for both transverse and longitudinal directions. The specified pipe dimensions allow for required transverse Charpy V-notch testi...

Open

9098

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching for intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and examination in accordance ...

Open

9099

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

9100

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

9101

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases. Source: DMV_STANDARD_BOOK/02...

Open

9102

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

9103

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria based on CVN and corrosion...

Open

9104

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully fulfilled. Source: DMV_STA...

Open

9105

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

9106

4.4.3

AI

No

add date

Microstructure examination is performed as per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at minimum 400X magnification. Acceptance criteria: structure must be basically free from intermetallic precipitates (isolate...

Open

9107

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS ...

Open

9108

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9109

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

9110

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 (ASTM A790, NORSOK M-630, M-650/ISO 17782) are fully met, including compliance for destructive and microstructural tests (tensile, impact, corrosion, ferrite, microstructure). ...

Open

9111

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

9112

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

9113

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is confirmed for the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12...

Open

9114

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. For the specified OD (219.1 mm), eddy current testing is not feasible at Montbard, and hydrostatic/ultrasonic tests are only available at ...

Open

9115

5.2

AI

No

add date

No document confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair; NDE feasibility for the specified OD is also not guaranteed at the plant. Source: DMV_STANDARD_BOOK/02-03-01 - Digest AS...

Open

9116

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 for ASTM A790 pipe) unless otherwise specified, with no overriding requirements from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD...

Open

9117

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9118

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 (§14), both requiring traceability to melt and heat treatment lot. Marking methods (indelible black ink and vibro-etching) include heat and DMV lot numbers, ensuring full traceability as r...

Open

9119

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

9120

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

9121

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

9122

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification dem...

Open

9123

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

9124

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9125

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference). ...

Open

9126

10.2

AI

No

add date

EN 10204 3.1 certificates are stated to include NORSOK M-650/ISO 17782 identification, melting practice, refining method, heat treatment condition, heat number, chemical analysis, and test results, but only the country of origin—not the specific stee...

Open

9127

1.0

AI

No

add date

DMV 25.7N (UNS S32760) is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, and the manufacturing process is M-650 qualified for the required wall thickness. 'A790 NORSOK' is explicitly listed under customer specifications for the reques...

Open

9128

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N but not to ISO 17782; no confirmation of QTR/MPCR availability or full compliance with both standards as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORS...

Open

9129

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

9130

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9131

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. The chemical composition table in the requirement matches the standard for S32760, and compliance is confirme...

Open

9132

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

9133

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

9134

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

9135

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), corrosion, and microstructure at specified thickness locations, is performed as required by ASTM A790 and NO...

Open

9136

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

9137

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets or exceeds the required minimum tensile strength (750 MPa), yield strength (550 MPa), elongation (25%), and maximum hardness (310 HBW) per NORSOK MDS D51 Rev 6 and ASTM A790 for S32760. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

9138

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement for wall thickness and testing standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive test...

Open

9139

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -466C: minimum absorbed energies of 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe wall thickness (18.26mm) allows both transverse...

Open

9140

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

9141

4.4.1

AI

No

add date

Etching with 20–40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

9142

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

9143

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases. Source: DMV_STANDARD_BOOK/02...

Open

9144

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, actual magnification and scale bar reported, fulfilling the requirement for a representative micrograph at or near mid-wall thickness if intermetallic pha...

Open

9145

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

9146

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates below 10μm, which does not fully meet the requirement that none are permitte...

Open

9147

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_ST...

Open

9148

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, including etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and co...

Open

9149

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

9150

4.5

AI

No

add date

ASTM G48 Method 'A' corrosion testing at 50°C for 24h in accordance with ISO 17781 is not explicitly mentioned or referenced; compliance cannot be confirmed based on the available information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Mo...

Open

9151

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

9152

4.5

AI

No

add date

Corrosion test per ISO 17781 G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

9153

5.1

AI

No

add date

No information is provided regarding the qualification, certification, or defined roles and responsibilities of NDE personnel to ISO 9712 level II or III or equivalent. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montb...

Open

9154

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially aligned with available hydrostatic, EC, or UT testing, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed or qualified. For OD...

Open

9155

5.2

AI

No

add date

No provided documentation explicitly confirms that indications greater than the calibration notch are considered defects requiring rejection or repair, nor that the required NDE can be performed as standard for the specified pipe dimensions and grade...

Open

9156

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 seamless pipe are per the applicable ASTM standard (ASTM A999), with no alternative tolerances specified by TechnipFMC. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STAN...

Open

9157

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9158

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790, ensuring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number identification, fulfilling the requirement for traceability. Source: DMV...

Open

9159

9.0

AI

No

add date

Weld repairs are explicitly not acceptable as per NORSOK MDS D51 Rev 06, §14 for the specified product. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51...

Open

9160

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

9161

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

9162

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, fulfilling supplier qualification documentation per SIR...

Open

9163

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates ensuring traceability and required quality documentation to the delivered products as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

9164

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

9165

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, steel melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destruct...

Open

9166

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

9167

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of full qualification to NORSOK M-650/ISO 17782 or availability of QTR/MPCR documentation as required by the specification. Source:...

Open

9168

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

9169

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9170

3.1

AI

No

add date

DMV 25.7N (UNS S32760) fulfills the chemistry requirements per Table 2 and PREN minimum, in accordance with ASTM A790 and NORSOK MDS D51 Rev 06. Heat analysis and manufacturing process qualification are confirmed as compliant. Source: Digest ASTM A 7...

Open

9171

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

9172

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

9173

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and direct reference to Table 3, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

9174

4.1

AI

No

add date

DMV 25.7N seamless pipes are tested per NORSOK MDS D51/ASTM A790 requirements: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure at specified locations and directions. For...

Open

9175

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

9176

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required by NORSOK MDS D51 Rev 6 and ASTM A790 for Table 4 mechanical properties. Source: DMV_STANDARD_...

Open

9177

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and standards; requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/1...

Open

9178

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse values of 45 J (average) and 35 J (single), and minimum longitudinal values of 65 J (average) and 50 J (single) if transve...

Open

9179

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants after final polishing, fulfilling the requirement for 25 Cr Duplex stainless steels. Source: DMV...

Open

9180

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

9181

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

9182

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781, with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STAND...

Open

9183

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

9184

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

9185

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully met. Source: DMV_STANDAR...

Open

9186

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

9187

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosio...

Open

9188

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS ...

Open

9189

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9190

4.5

AI

No

add date

DMV 25.7N (UNS S32760) fulfills all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782 qualification, including chemical composition, mechanical properties, impact, corrosion, microstructure, an...

Open

9191

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

9192

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

9193

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

9194

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782-specific NDE criteria are not validated. Standard NDE methods (eddy current, hydrostatic, ultrasonic) for the requested OD are only available at extra cost and ...

Open

9195

5.2

AI

No

add date

None of the referenced documents explicitly confirm that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor do they confirm that the specified NDE will be performed as standard for the requeste...

Open

9196

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 seamless pipe are per the applicable ASTM standard (ASTM A999), with no overriding specification from TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances ...

Open

9197

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot; marking methods (indelible ink, vibro-etching) include heat number and DMV lot number, ensuring traceability as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NOR...

Open

9198

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dige...

Open

9199

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

9200

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the required quality-assurance system specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORS...

Open

9201

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

9202

10.2

AI

No

add date

ISO 9001 certification is provided and documentation traceable to the products, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO 17782 manufacturing summary or QTR number, is transmitted to TechnipFMC as required by SIR205. Source: DMV_S...

Open

9203

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630 (heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary or QTR number)....

Open

9204

10.2

AI

No

add date

NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition are included in the EN 10204 3.1 certificate, but only the country of origin of the steel supplier is provided, not the specific steel producer. Solution anne...

Open

9205

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all required chemical, mechanical, manufacturing, and testing requirements. M-650 qualification is confirmed for the specified wall...

Open

9206

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782, nor confirmation of QTR/MPCR documentation availability for review. Only M-650 accreditation is mentioned, with ISO 17782 missing and no supporting documentation referenced. So...

Open

9207

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, with manufacturing process qualified to NORSOK M-650 or ISO 17782 and meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

9208

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9209

3.1

AI

No

add date

Chemical composition for S32760 matches Table 2 requirements and is confirmed to conform to ASTM A790 with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02...

Open

9210

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are placed to ensure free ...

Open

9211

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

9212

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and direct reference to Table 3, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

9213

4.1

AI

No

add date

Test sampling for seamless pipes per ASTM A790/NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure at specified thickness locations. For the ord...

Open

9214

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

9215

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9216

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and meets the minimum wall thickness requirements of ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-0...

Open

9217

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse average/single values of 45 J/35 J, and longitudinal average/single values of 65 J/50 J if transverse is not possible. The...

Open

9218

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, fulfilling the requirement. Source: DMV_STANDARD...

Open

9219

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

9220

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

9221

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 is performed at a minimum magnification of 400x, with etching to detect intermetallic phases; presence and location are noted and recorded with micrographs. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

9222

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

9223

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

9224

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10μm and does not explicitly prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed, as required by the client specification. Source: DMV_STANDARD_...

Open

9225

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Sou...

Open

9226

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in...

Open

9227

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Structure must be basically free from intermetallic precipitates; isolated precipitates allowed if not d...

Open

9228

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

9229

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided; neither ASTM G48 nor ISO 17781 are mentioned, and the required test is not specified. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests i...

Open

9230

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, with manufacturing and qualification in accordance with NORSOK M-650/ISO 17782. Source: DM...

Open

9231

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

9232

5.1

AI

No

add date

No information is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility...

Open

9233

5.2

AI

No

add date

DMV Germany performs 100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 or ISO 10893-10 after all mechanical processing, heat treatments, and straightening, with reference notches introduced per ASTM E213 requirements for c...

Open

9234

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially met, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For OD 219.1 mm, standard NDE methods (EC, UT, hydrostatic) are only ...

Open

9235

5.2

AI

No

add date

No provided source explicitly confirms that indications greater than the calibration notch are considered defects requiring rejection or repair per NDE acceptance criteria for ASTM A790/NORSOK MDS D51. NDE is referenced, but specific acceptance crite...

Open

9236

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 seamless pipe are per the applicable ASTM standard (ASTM A999), with OD, WT, and ovality tolerances confirmed for the requested dimensions. No deviations or special tolerance requests are indicated in the customer...

Open

9237

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9238

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13...

Open

9239

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9240

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

9241

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, meeting the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-0...

Open

9242

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, and QTR number is included as per M-650 qualification, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MCPR...

Open

9243

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation traceable to delivered products as required by SIR205 and specification section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

9244

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications and plant documentation. Source: DMV_STANDARD_BOOK/02-04-03 - Dig...

Open

9245

10.2

AI

No

add date

Documentation and certification requirements are not fully met: NORSOK M-650/ISO 17782 identification, steel melting practice, heat treatment condition, and other required details are confirmed to be included in the EN 10204 3.1 certificate, but the ...

Open

9246

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by specification references and digest documentation. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9247

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03...

Open

9248

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

9249

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9250

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9251

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling (water quenching) per ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650/ISO 17782. Pipes are placed to ensure free circulation of heating and cooling media...

Open

9252

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

9253

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and direct reference to Table 3, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

9254

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if transverse not possible), and corrosion/microstructure tests are performed as specified. F...

Open

9255

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 as specified for DMV 25.7N (UNS S32760). Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9256

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

9257

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the requested pipe dimensions, which exceed the minimum wall thickness required by the standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testin...

Open

9258

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C with minimum transverse values of 45 J (average) and 35 J (single), and longitudinal values of 65 J (average) and 50 J (single) if transverse ...

Open

9259

4.4.1

AI

No

add date

Micrographic examination and ferrite check are performed as per ISO 17781, but the exact etchant solution required for detecting intermetallic phases and ferrite balance after final polishing is not explicitly confirmed. Only general etchants are men...

Open

9260

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

9261

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

9262

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781, with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STAND...

Open

9263

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

9264

4.4.2

AI

No

add date

Micrographic examination requires reporting of centerline intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

9265

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

9266

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

9267

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781 at ≥400X magnification, with etching to detect intermetallic phases, nitrides, and carbides. Acceptance criteria: structure is basically free from intermetallic precipitates (isolated, non-distribut...

Open

9268

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

9269

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9270

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

9271

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

9272

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

9273

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT at 100%) is detailed, but compliance with additional NDE requirements of NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782 is not confirmed. For OD 219.1 mm, eddy current testing is not feasible at Mo...

Open

9274

5.2

AI

No

add date

None of the referenced documents explicitly confirm that indications greater than the calibration notch are classified as defects requiring rejection or repair, nor do they specify this acceptance criterion for NDE as required by the specification. S...

Open

9275

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and ASTM A999 as required, with no override by TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 790-02.doc, DMV_STAND...

Open

9276

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: ASTM A790 digest, NORSOK MDS D51 Rev 6 digest.

Open

9277

8.0

AI

No

add date

Marking per ASTM A790 includes traceability to melt and heat treatment lot; marking methods (indelible ink, vibro-etching) include heat number and DMV lot number, ensuring full traceability. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

9278

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly prohibits weld repairs under 'Surface finish / Repairs of defects' (§13, §14). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

9279

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

9280

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

9281

10.1

AI

No

add date

Supplier is M-650 accredited for DMV25.7N up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the requirement for qualification demonstration. Source: DMV_S...

Open

9282

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and specification section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

9283

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is standard and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

9284

10.2

AI

No

add date

Most documentation requirements are addressed, but the steel producer of the starting material is not specifically identified (only country of origin is provided), and actual solution annealing parameters and test results are not included. NORSOK M-6...

Open

9285

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and are M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 -...

Open

9286

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782. No evidence of QTR/MPCR documentation availability. Requirement for NORSOK M-650/ISO 17782 qualification and documentation is not fully fulf...

Open

9287

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

9288

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9289

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9290

3.2

AI

No

add date

Pipes are solution annealed followed by water quenching per ASTM A790, furnaces are qualified to NORSOK M-650/ISO 17782, and pipe arrangement ensures free circulation of heating and cooling media during heat treatment including accelerated cooling. S...

Open

9291

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

9292

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for sampling frequency and method, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests...

Open

9293

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure at specified locations. For NPS 8 (219.1 mm OD...

Open

9294

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with mechanical properties meeting Table 4 (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%). Hardness testing is performed per ASTM A790, and results are provided. Source: DMV_STAN...

Open

9295

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

9296

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions (18.26mm WT, 219.1mm OD) in both longitudinal and transverse directions as required by the specification. Source: DMV_STANDARD_BOOK/12 - Spec...

Open

9297

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if transverse ...

Open

9298

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, using 20-40% NaOH or KOH solution for etching after final polishing, fulfilling the requirement for metallographic preparation and examination and sp...

Open

9299

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

9300

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

9301

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9302

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

9303

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

9304

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

9305

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

9306

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

9307

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: microstructure examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides r...

Open

9308

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

9309

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781; requirement not confirmed. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9310

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/...

Open

9311

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

9312

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

9313

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed after all mechanical processing, heat treatments, and straightening, with acceptance of ASTM E213 implying compliance with calibration notch requirements. Sou...

Open

9314

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially addressed with 100% hydrostatic or NDE (EC or UT) per ASTM A999, but there is no evidence of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782. For OD 219.1 mm, eddy current testi...

Open

9315

5.2

AI

No

add date

No provided documentation confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, and standard NDE methods for the specified OD are not feasible at Montbard. Source: DMV_STANDARD_BOOK/02-03-0...

Open

9316

6.0

AI

No

add date

Dimensional tolerances are specified as per ASTM A790 and ASTM A999, which are the applicable ASTM standards for seamless pipe, and there is no overriding specification from TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_S...

Open

9317

8.0

AI

No

add date

Marking includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, 13-02-01 - Standard marking ...

Open

9318

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9319

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

9320

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORS...

Open

9321

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

9322

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to delivered products, meeting the documentation and traceability requirements for TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

9323

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided, including all information required by ASTM A790 and NORSOK M-630, and validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certifica...

Open

9324

10.2

AI

No

add date

Partial fulfillment: EN 10204 3.1 certificate will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MPCR number, steel melting practice, and heat treatment condition. Only country of origin of steel supplier is provided, not...

Open

9325

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all relevant mechanical, chemical, and testing requirements. Manufacturing is M-650 qualified for the required wall thickness. Source:...

Open

9326

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability or full qualification to both required standards for the exact product supplied. Source: 02-04-03 - Dig...

Open

9327

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

9328

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9329

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9330

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling (water quenching) per ASTM A790; manufacturing process and furnaces are qualified to NORSOK M-650/ISO 17782; proper pipe placement for free circulation during heat treatment is ensur...

Open

9331

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot, with 'lot' defined according to ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

9332

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

9333

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per NORSOK MDS D51/ASTM A7...

Open

9334

4.2

AI

No

add date

Tensile testing is performed in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 as required for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

9335

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required by NORSOK MDS D51 Rev 6 and ASTM A790 for seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

9336

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the requested pipe dimensions, which exceed the minimum wall thickness requirements for both ASTM and ISO standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 -...

Open

9337

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse (average/single) 45 J/35 J, minimum longitudinal (average/single) 65 J/50 J if transverse not possible, and testing on thi...

Open

9338

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with specified etchants for intermetallic phases and ferrite balance after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

9339

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH solution or other suitable etchant(s) to show ferrite balance and intermetallic phases is required, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spe...

Open

9340

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

9341

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781, with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded as required. Sourc...

Open

9342

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

9343

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

9344

4.4.2

AI

No

add date

The available specifications allow isolated intermetallic precipitates below 10μm, but do not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed, as required by the client specification. Source: DMV_STANDARD_BO...

Open

9345

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

9346

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781 at ≥400X magnification, with etching to detect intermetallic phases, nitrides, and carbides. Acceptance criteria: structure must be basically free from intermetallic precipitates; isolated precipita...

Open

9347

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9348

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) performed in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9349

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive tests, microstructure, and ferrite content requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

9350

4.5

AI

No

add date

DMV 25.7N meets the requirement of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 ...

Open

9351

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

9352

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

9353

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT) is detailed, but there is no explicit confirmation that NORSOK-specific NDE requirements are met. Eddy current testing is not feasible for the required OD at Montbard, and hydrostatic/ultrasonic tests a...

Open

9354

5.2

AI

No

add date

The requirement for rejecting or repairing pipe/tubing based on NDE indications greater than the calibration notch is not explicitly confirmed in the referenced specifications, and standard NDE is not available for the requested OD at Montbard, makin...

Open

9355

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 790-02 (A 99...

Open

9356

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSO...

Open

9357

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods include heat number and DMV lot number, ensuring traceability for 100% of pipes as required for Montba...

Open

9358

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

9359

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

9360

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

9361

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demons...

Open

9362

3.1

AI

No

add date

AOD or equivalent refining is standard practice and required for 100% of production; chemical analysis for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9363

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and specification section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

9364

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification summary. Source: DMV_STANDARD_BOOK...

Open

9365

10.2

AI

No

add date

No provided documentation contains the required NORSOK M-650/ISO 17782 identification, steel producer, steel melting practice, heat number, actual chemical analysis results, solution annealing parameters, or results of all metallurgical and non-destr...

Open

9366

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and are M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BO...

Open

9367

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782, and no confirmation of Qualification Test Record availability is provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9368

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

9369

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis for DMV 25.7N complies with Table 2 of ASTM A790 and NORSOK MDS D51 Rev 6. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9370

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. The chemical composition table matches the standard and compliance is confirmed for the proposed grade. Sourc...

Open

9371

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

9372

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

9373

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and direct reference to Table 3, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

9374

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile tests are performed longitudinally or transversely, hardness, CVN (transverse, longitudinal if not possible), and corrosion/microstructure tests are c...

Open

9375

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with mechanical properties meeting Table 4 requirements (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%). Hardness testing is performed per ASTM A790, referencing ASTM A370. DMV 25...

Open

9376

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

9377

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness (>6mm), fulfilling the requirement. Source: 12-03-02 - Impact Test for hot finished products.doc

Open

9378

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse average/single values of 45 J/35 J, longitudinal average/single values of 65 J/50 J (if transverse not possible), and sub-s...

Open

9379

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781, with etching by 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and exa...

Open

9380

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

9381

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

9382

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

9383

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

9384

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

9385

4.4.2

AI

No

add date

No document fully prohibits intermetallic phases and/or precipitates when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10µm, which does not meet the zero-tolerance requirement in this scenario. Source: DMV...

Open

9386

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

9387

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impa...

Open

9388

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

9389

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9390

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

9391

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

9392

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor are their roles and responsibilities defined as per ISO 9712 or equivalent standard. Source: DMV_STANDARD_BOOK/12...

Open

9393

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic ...

Open

9394

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790/NORSOK M-630 MDS D51 are not fully addressed; only general NDE or hydrostatic testing per ASTM A999 is confirmed, and for the required OD, eddy current and ultrasonic testing are only available at extra cost and ...

Open

9395

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor that NDE to this sensitivity is feasible or standard for the specified dimensions at Montbard. S...

Open

9396

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (A790/A999) for the specified pipe dimensions, with no overriding requirements from TechnipFMC indicated. Source: 07.01 - General information.doc, 07.03.01 - Tolerances according to ASTM A 3...

Open

9397

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9398

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 (§14), requiring full traceability to melt and heat treatment lot. Marking methods include heat number and DMV lot number as standard content, ensuring compliance with the requirement for ...

Open

9399

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

9400

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

9401

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

9402

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

9403

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, are provided and meet the requirement for documentation traceable to delivered products as per...

Open

9404

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

9405

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9406

10.2

AI

No

add date

Documentation and certification will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin—not the specific steel producer—will be provided. No actual data or results for h...

Open

9407

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as required for 25 Cr Duplex stainless steel seamless pipes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

9408

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N but not to ISO 17782, as required. No confirmation of QTR/MPCR availability. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9409

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

9410

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9411

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN requirements per ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9412

3.2

AI

No

add date

DMV 25.7N manufacturing is qualified to NORSOK M-650, heat treatment is solution annealing followed by accelerated cooling per ASTM A790, furnaces comply with NORSOK M-650/ISO 17782, and process ensures free circulation of heating/cooling media durin...

Open

9413

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

9414

4.1

AI

No

add date

Tensile test specimen sampling is performed according to Table 3 of ASTM A790, fulfilling the requirement for test specimen sampling as outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-0...

Open

9415

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specifi...

Open

9416

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

9417

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

9418

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and standards; requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/1...

Open

9419

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact test requirements at -466C, meeting minimum absorbed energy values in both transverse and longitudinal directions, and the specified pipe dimensions allow for required testing directions and speci...

Open

9420

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

9421

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

9422

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

9423

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

9424

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

9425

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

9426

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. No evidence of stricter prohibition is provided in the ava...

Open

9427

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

9428

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with required etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impac...

Open

9429

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

9430

4.5

AI

No

add date

No explicit confirmation that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9431

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive, micrographic, corrosion tests, ferrite content, heat treatment, and manufacturing process requirements; plant is M-650 accredited for this grade an...

Open

9432

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

9433

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

9434

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects is performed in accordance with ASTM E213 or ISO 10893-10, including reference notches and calibration as per ASTM E213. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/1...

Open

9435

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

9436

5.2

AI

No

add date

NDE requirements per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not addressed; only ASTM A790/A999 NDE is confirmed. For OD 219.1 mm, Eddy current testing is not feasible, and hydrostatic/ultrasonic tests incur extra cost. Full-length dye pe...

Open

9437

5.2

AI

No

add date

None of the provided documents explicitly state that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, nor confirm feasibility of the required NDE for the specified dimensions at Mon...

Open

9438

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standards (A790/A999) as required, with no deviations or special tolerances indicated by TechnipFMC. Source: 07.01 - General information.doc, 07.03.01 - Tolerances ac...

Open

9439

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9440

8.0

AI

No

add date

Marking per ASTM A790 and standard plant methods includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.do...

Open

9441

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' (§13, §14) for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

9442

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

9443

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

9444

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

9445

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to the products, fulfilling the requirement for a quality-assurance system and traceable documentation to be transmitted to TechnipFMC as per SIR205. Source...

Open

9446

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - ...

Open

9447

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and results of all metallurgical and non-...

Open

9448

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 -...

Open

9449

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm, cold finished up to WT = 10.925 mm), but not to ISO 17782 as required. No evidence of QTR/MPCR availability provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest N...

Open

9450

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N within the required wall thickness range, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_...

Open

9451

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production, and DMV 25.7N complies with the specified chemical composition per Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Re...

Open

9452

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN ≥ 40, as required by NORSOK MDS D51 Rev 06 and ASTM A790 Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9453

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

9454

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

9455

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

9456

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified l...

Open

9457

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

9458

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

9459

4.3

AI

No

add date

Charpy V-notch testing in accordance with ASTM A370 and ISO 148-1 is feasible for the specified pipe dimensions and fulfills the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 ...

Open

9460

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, with minimum absorbed energy values for transverse and longitudinal specimens, and the specified pipe dimensions allow for proper testing orientation and fulfillmen...

Open

9461

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with specified etchants for intermetallic phases and ferrite balance after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

9462

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is explicitly required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_...

Open

9463

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

9464

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

9465

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

9466

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 includes etching to detect intermetallic phases, requires reporting of intermetallics, and acceptance is based on CVN and corrosion test results as specified in the requirement. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

9467

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fulfilled. Source: DMV_S...

Open

9468

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

9469

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), in compliance with the requir...

Open

9470

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

9471

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9472

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9473

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

9474

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

9475

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

9476

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but compliance with NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 is not demonstrated. For OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at extra cost. Full-le...

Open

9477

5.2

AI

No

add date

None of the relevant documents explicitly state that any indication greater than that produced by the calibration notch represents a defect, nor do they confirm that defective pipe and tubing shall be rejected or repaired according to this criterion....

Open

9478

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the specified pipe size, with no deviations or special requirements stated by the customer. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/...

Open

9479

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9480

8.0

AI

No

add date

Marking is per ASTM A790 §14, requiring full traceability to melt and heat treatment lot. Marking methods include heat number and DMV lot number, ensuring traceability as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORS...

Open

9481

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

9482

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

9483

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for material manufacturers as specified in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

9484

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

9485

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

9486

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630 for 25Cr Duplex Stainless Steel seamless pipe, with validation by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D...

Open

9487

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all required metallurgic...

Open

9488

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, fulfilling the requirement for 25 Cr Duplex stainless steel seamless pipes as specified. Source: DMV_STANDA...

Open

9489

1.0

AI

No

add date

No evidence is provided that the supplier is qualified to NORSOK M-650/ISO 17782 for the exact product supplied or that the full Qualification Test Record/MPCR is available for review. One source confirms NORSOK M-650 accreditation but explicitly sta...

Open

9490

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm for hot finished, 10.925 mm for cold finished), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 require...

Open

9491

3.1

AI

No

add date

AOD or equivalent refining is used for DMV 25.7N, and the chemical analysis complies with the specified requirements in Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9492

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the product's WT of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest ...

Open

9493

3.2

AI

No

add date

Heat treatment is solution annealing followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782, and procedures ensure free circulation of heating and cooling media around each pi...

Open

9494

4.1

AI

No

add date

No provided document confirms that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790. Testing frequency, lot definition, and full test co...

Open

9495

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

9496

4.1

AI

No

add date

Tensile, hardness, and CVN tests on prolongation samples from seamless pipes are covered per ASTM A790, with test directions and locations matching the requirement. CVN testing is allowed as a supplementary requirement if specified in the purchase or...

Open

9497

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature with criteria matching or exceeding Table 4 (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%), and NORSOK MDS D51 references ASTM A790, which requires mechanical testing per ASTM A370, fulfilling the re...

Open

9498

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required for DMV 25.7N are not provided or confirmed in the available documentation; referenced documents either lack the specific values or address different grades....

Open

9499

4.3

AI

No

add date

No evidence that Charpy V-notch testing will be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1, or that results will meet Table 5 requirements for the specified product and order context. Relevant documents discuss feasibility but d...

Open

9500

4.3

AI

No

add date

Impact testing at -466C with specified absorbed energy values is fulfilled for pipe with 18.26mm wall thickness; both longitudinal and transverse specimens are feasible and requirements are met. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 -...

Open

9501

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination according to ISO 17781 or specification of the required etchant for 25 Cr Duplex stainless steels; available documentation only addresses austenitic materials and excludes duplex steels. Sourc...

Open

9502

4.4.1

AI

No

add date

No information confirming the use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination is provided or referenced. Requirement not fulfilled for etchant specification or standard complian...

Open

9503

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

9504

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided or addressed in the relevant documents or comments. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03...

Open

9505

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at 400x minimum magnification with a scale bar when intermetallic phases are not detected. Partial mention of 400x magnification and photos, but not a...

Open

9506

4.4.2

AI

No

add date

No relevant documentation addresses the reporting or acceptance criteria for centerline intermetallic stringers or links their acceptance to CVN and corrosion test results in the event such stringers are present. Source: DMV_STANDARD_BOOK/12-03-03 - ...

Open

9507

4.4.2

AI

No

add date

NORSOK MDS D41 Rev 06 and D51 Rev 06 allow isolated intermetallic precipitates below 10μm if not distributed over the whole specimen, which does not meet the stricter client requirement of zero tolerance for intermetallic phases and/or precipitates w...

Open

9508

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided; only grain size examination is addressed, not the required ferrite determination methods or standards. Source: DMV_STANDARD_BOOK/12 - S...

Open

9509

4.4.3

AI

No

add date

No provided document specifies acceptance criteria or results for micrographic examination or metallurgical properties for DMV 25.7N as required in section 4.4; requirement not fulfilled by available information. Source: DMV_STANDARD_BOOK/02-03-01 - ...

Open

9510

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.d...

Open

9511

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9512

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are provided in the referenced documents or requirement section, making validation impossible for DMV 25.7N against the client specification. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

9513

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria: no pitting at 20X magnification and weight loss < 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

9514

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Sources: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STAND...

Open

9515

5.2

AI

No

add date

No explicit confirmation that 100% ultrasonic testing per ASTM E213 or ISO 10893-10, after all processing steps and with specified calibration notches, is performed for the pipe base material. Dimensional feasibility for ultrasonic testing is provide...

Open

9516

5.2

AI

No

add date

100% qualitative anti-mixing PMI is standard at Montbard, fulfilling the NDE acceptance criteria for PMI unless quantitative PMI is specifically requested, which is not indicated here. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destru...

Open

9517

5.2

AI

No

add date

ASTM A790 requires NDE per ASTM A999, which mandates that any indication greater than the calibration notch is cause for rejection or repair, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed...

Open

9518

1.0

AI

No

add date

No evidence is provided that the supplier is qualified in accordance with NORSOK M-650/ISO 17782 for the exact product supplied, nor is there confirmation of the availability of Qualification Test Record/Manufacturer Procedure Conformity Records for ...

Open

9519

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N meets the chemical composition requirements of Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

9520

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for hot and cold finished products are confirmed as per the applicable ASTM standards (including ASTM A790/A999) for the relevant size ranges, with no deviations or overrides indicated by TechnipFMC part...

Open

9521

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and NORSOK MDS S01, fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790, NORSOK MDS S01.

Open

9522

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

9523

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

9524

10.0

AI

No

add date

No evidence of an appropriate quality-assurance system (such as ISO 9001 certification by a competent EEA body) is provided for the material manufacturer or Montbard plant. No certification details or proof of compliance are present in the reviewed d...

Open

9525

10.1

AI

No

add date

No evidence provided that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body with a specific assessment for materials as required by the specification. Source: 14-03 - Certification Montbard plant.doc

Open

9526

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for UNS S32760/DMV25.7N up to the required wall thickness, demonstrating qualification for the size and product form. Source:...

Open

9527

10.2

AI

No

add date

No evidence that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC; no confirmation of ISO 9001 (or equivalent) quality-assurance certification or its transmission to TechnipFMC as required. Source: DMV_...

Open

9528

10.2

AI

No

add date

Material certificate is issued according to EN 10204 Type 3.1 and validated by Quality Control; reference to DMV 25.7N and NORSOK in the order metadata suggests compliance with ASTM A790 and NORSOK M-630 information requirements. Source: 14-03 - Cert...

Open

9529

10.2

AI

No

add date

None of the reviewed documents provide the required documentation or certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details,...

Open

9530

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with all relevant mechanical, chemical, and testing requirements addressed for the specified grade and prod...

Open

9531

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm for hot finished, 10.925 mm for cold finished), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 require...

Open

9532

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the requested product (WT = 18.26 mm). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

9533

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed per ASTM A790, manufacturing process and furnaces are qualified according to NORSOK M-650/ISO 17782, and free circulation of heating/cooling media is ensured by complian...

Open

9534

4.1

AI

No

add date

No evidence that impact, tensile, hardness, corrosion testing, and microstructure examinations are performed for each heat and heat treatment lot as defined in ASTM A790; only partial or unrelated information is provided for individual tests without ...

Open

9535

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

9536

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no evidence of CVN, hardness, corrosion, or microstructure testing, nor confirmation of required test directions and sampling locations as specified in Table 3. Source: DMV_STANDARD_BOOK/02-03-...

Open

9537

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

9538

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required in Table 4 for DMV 25.7N are not confirmed in the provided documents; referenced standards do not reproduce or explicitly state the required values for this ...

Open

9539

4.3

AI

No

add date

No evidence that Charpy V-notch testing is performed or reported in accordance with ASTM A370, ASTM A1058, or ISO 148-1, or that results meet Table 5 requirements for the specified product and order context. Source: 02-02-01 Digest summary of ASTM A....

Open

9540

4.3

AI

No

add date

Impact testing at -46°C with specified absorbed energy values is feasible and can be fulfilled for the pipe with 18.26mm wall thickness, as both longitudinal and transverse specimens can be taken. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for ...

Open

9541

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination according to ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - ...

Open

9542

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination; requirement not fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - ...

Open

9543

4.4.2

AI

No

add date

Micrographic examination requires the microstructure to be basically free from intermetallic phases, allowing isolated phases if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - S...

Open

9544

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided or addressed in the relevant documents or comments. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03...

Open

9545

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and DMV material composition conforms with supplier certification and heat analysis per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed diges...

Open

9546

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at actual magnification (400x minimum) with a scale bar when intermetallic phases are not detected. Requirements for actual magnification and scale ba...

Open

9547

4.4.2

AI

No

add date

No relevant documents address the presence, reporting, or acceptance criteria for centerline intermetallic stringers, nor their relation to CVN or corrosion test results.

Open

9548

4.4.2

AI

No

add date

Referenced specifications allow isolated intermetallic precipitates below 10 µm if not distributed over the whole specimen, while the client requires that intermetallic phases and/or precipitates are not permitted at all if CVN testing cannot be comp...

Open

9549

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided or addressed in the reviewed documents. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Micrograph...

Open

9550

4.4.3

AI

No

add date

No provided documents specify acceptance criteria or results for micrographic examination or metallurgical properties relevant to section 4.4 Micrographic Examination for DMV 25.7N. Requirement not fulfilled by the given information. Source: DMV_STAN...

Open

9551

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9552

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided in the relevant documentation or metadata. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9553

4.5

AI

No

add date

No explicit acceptance criteria for metallurgical properties are specified; only a heading is present without defined requirements or values for DMV 25.7N. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Dige...

Open

9554

4.5

AI

No

add date

Specification requires pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², matching the client's requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

9555

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDA...

Open

9556

5.2

AI

No

add date

It is confirmed that the requested pipe dimensions are within ultrasonic testing capability, but there is no evidence that testing is performed after all processing steps or that calibration notches meet ASTM E213 Figure 3 requirements. Source: DMV_S...

Open

9557

5.2

AI

No

add date

100% qualitative anti-mixing PMI checks are standard at Montbard, with defined procedures and reporting for quantitative PMI when required, fulfilling the NDE/PMI requirement. Source: DMV_STANDARD_BOOK/12-06-06 - Positive Material Identification (PMI...

Open

9558

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor is there confirmation that the required NDE is standardly performed or feasible for the sp...

Open

9559

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, with qualification testing meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_S...

Open

9560

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compliance...

Open

9561

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

9562

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed as per the applicable ASTM standards (including ASTM A790/A999) for the requested product, with no deviations or special tolerances indicated for the specified size range. Requirement is fu...

Open

9563

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790, NORSOK MDS S01.

Open

9564

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

9565

9.0

AI

No

add date

Weld repairs are explicitly stated as not acceptable for MST-Tubes in the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

9566

10.0

AI

No

add date

No evidence of an ISO 9001 certified quality-assurance system or certification by a competent EEA body with specific assessment for materials is provided in the referenced documents. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STAN...

Open

9567

10.1

AI

No

add date

No evidence that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification or that the required documentation will be submitted to TechnipFMC for approval. Source: DMV_STANDARD_BOOK/14-03 - Certification Mon...

Open

9568

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N up to WT 31.75 mm (requested WT 18.26 mm is within scope) and the EN 10204 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number. Source:...

Open

9569

10.2

AI

No

add date

No evidence that documentation traceable to the delivered products and to be transmitted to TechnipFMC (as per SIR205) will be provided for the Montbard plant or specific order. Certification and inspection documents are referenced, but explicit trac...

Open

9570

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control for mill inspection. Inclusion of information required by ASTM A790 and NORSOK M-630 is not explicitly confirmed, but the certificate type and validation...

Open

9571

10.2

AI

No

add date

No provided documents contain the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or test results for the ...

Open

9572

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/...

Open

9573

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability or full compliance with both NORSOK M-650/ISO 17782 as required. Source: DMV_STANDARD_BOOK/02-04-03 - D...

Open

9574

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

9575

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Dige...

Open

9576

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations a...

Open

9577

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the tensile and maximum hardness properties of Table 4 as specified in NORSOK MDS D51. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

9578

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 06 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

9579

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement for wall thickness and testing standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive test...

Open

9580

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C: minimum 45/35 J (average/single, transverse) and 65/50 J (average/single, longitudinal) for thickness >6mm. The specified pipe dimensions allow for required testing d...

Open

9581

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

9582

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified and matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

9583

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and if each is below 10µm, matching the requirement for distribution and size of intermetallic phases....

Open

9584

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

9585

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

9586

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_ST...

Open

9587

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

9588

4.4.3

AI

No

add date

Ferrite content is determined per ASTM E562 or by image analysis according to ASTM E1245, performed in accordance with ISO 17781, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

9589

4.4.3

AI

No

add date

Microstructure examination is performed as per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at minimum 400X magnification. Structure must be free from intermetallic precipitates except isolated ones below 10µm, and ca...

Open

9590

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

9591

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9592

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782 qualification, including chemical composition, mechanical properties, impact, corrosion, microstructure, and f...

Open

9593

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

9594

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712 for this requirement. Source: DMV_STANDARD_BOOK/12-02-01 - Non destru...

Open

9595

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

9596

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled; only ASTM A790/A999 NDE is detailed. For the specified OD (219.1 mm), eddy current and ultrasonic testing are not standard at Montbard and req...

Open

9597

5.2

AI

No

add date

None of the referenced documents explicitly state that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, nor do they confirm the required NDE acceptance criteria or feasibility for t...

Open

9598

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standards (including A999), with no deviations specified by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolera...

Open

9599

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9600

8.0

AI

No

add date

Marking includes heat number and DMV lot number using indelible ink or vibro-etching, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and standard practice at Montbard. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NO...

Open

9601

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 explicitly states 'Weld repairs not acceptable.' Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9602

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

9603

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

9604

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, fulfilling the qualification requirement. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

9605

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

9606

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

9607

10.2

AI

No

add date

Required documentation such as NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MPCR number, steel producer, heat number, chemical analysis, solution annealing parameters, and actual results of metallurgical and non-destructive test...

Open

9608

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification up to the required wall thickness. All relevant chemical, mechanical, and testing requirements are met for 25 Cr Dup...

Open

9609

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782, as explicitly required. No evidence provided for availability of QTR/MPCR documentation for review by TechnipFMC as required by the specification. Source: DMV_STANDARD_BOOK/02-...

Open

9610

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

9611

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9612

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN requirements per Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 06 standards. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev ...

Open

9613

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650/ISO 17782, and proper heat treatment practices ensuring compliance with f...

Open

9614

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

9615

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detaile...

Open

9616

4.1

AI

No

add date

Tensile, hardness, CVN (transverse or longitudinal as required), corrosion, and microstructure tests are performed on prolongation samples per ASTM A790 and NORSOK MDS D51 Rev 06. For the ordered pipe dimensions, transverse CVN sampling is feasible a...

Open

9617

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9618

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

9619

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 06 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

9620

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

9621

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C: minimum absorbed energies of 45 J (average) and 35 J (single) in the transverse direction, and 65 J (average) and 50 J (single) in the longitudinal direction if tran...

Open

9622

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching by 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and examination in accordance with ISO 17781 and the specified etchants. Sourc...

Open

9623

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is explicitly required for micrographic examination and is fulfilled by the specification digest. Source: DMV_STANDARD_B...

Open

9624

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

9625

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

9626

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

9627

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

9628

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size, so the requirement is not fully fulfilled. Sou...

Open

9629

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

9630

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corr...

Open

9631

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

9632

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9633

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive, micrographic, ferrite, corrosion tests, heat treatment, and manufacturing process requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

9634

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 24h, 50°C) is performed with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m²; DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

9635

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

9636

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed on the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - U...

Open

9637

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51 are not fully addressed; only general hydrostatic or NDE testing per ASTM A999 is confirmed, and plant feasibility for required NDE methods (Eddy current, Ultrasonic) is limited or requir...

Open

9638

5.2

AI

No

add date

No provided document confirms that indications greater than the calibration notch are classified as defects requiring rejection or repair, nor that the required NDE acceptance criterion is applied for the specified pipe dimension at Montbard. NDE fea...

Open

9639

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standards (ASTM A999), with no override by TechnipFMC indicated in the provided context. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/...

Open

9640

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9641

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Standard marking practices at Montbard include heat and DMV lot numbers, ensuring compliance with the traceability requirement....

Open

9642

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

9643

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

9644

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body established within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

9645

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

9646

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products being delivered as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

9647

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, 14-03 - Certification Montbard plant.doc

Open

9648

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all required metallurgic...

Open

9649

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with all required tests, certifications, and M-650 qualification covered for the specified wall thickness and grade. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

9650

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9651

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

9652

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev...

Open

9653

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PREN ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9654

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N, and certification will state heat treatment condition...

Open

9655

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is carried out for each heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

9656

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

9657

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests are performed at specifie...

Open

9658

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

9659

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

9660

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact ...

Open

9661

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor are their roles and responsibilities defined as per ISO 9712 requirements. Source: DMV_STANDARD_BOOK/12-02-01 - N...

Open

9662

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact test requirements at -466C, meeting minimum absorbed energy values for both transverse and longitudinal directions, including sub-size reduction factors. The specified pipe dimensions allow for re...

Open

9663

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

9664

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect intermetallic phases, in accordance with ISO 17781, is required for micrographic examination, fulfilling the requirement for suitable etchant(s) as listed in ISO 17781 Appendix B to show ferrite balance and ...

Open

9665

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

9666

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are reported with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

9667

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

9668

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

9669

4.4.2

AI

No

add date

No explicit prohibition of intermetallic phases and/or precipitates is stated for cases where CVN testing cannot be completed; isolated intermetallic precipitates below 10µm are allowed if not distributed over the whole specimen, and acceptance is ba...

Open

9670

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

9671

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance is based on im...

Open

9672

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

9673

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9674

4.5

AI

No

add date

DMV 25.7N complies with all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive tests, microstructure, ferrite content, and M-650 qualification for the specified grade and wall thickness. Source: DMV_STANDARD_BOOK/02 - S...

Open

9675

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02...

Open

9676

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782; full qualification per NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR is not confirmed. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev...

Open

9677

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects is performed in accordance with ASTM E213 or ISO 10893-10 for the required pipe dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 ...

Open

9678

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no explicit evidence of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782. Eddy current testing is not feasible for the required OD at Montbard, and other NDE methods (eddy current, dye ...

Open

9679

5.2

AI

No

add date

No provided document explicitly states that any indication greater than the calibration notch is considered a defect requiring rejection or repair, and standard NDE methods are not feasible for the requested OD at Montbard. Source: 02-03-01 - Digest ...

Open

9680

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790), with no deviations or overrides specified by TechnipFMC. Tolerances for OD, WT, and ovality for the requested dimensions are compliant...

Open

9681

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9682

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/1...

Open

9683

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 (§13, §14) for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

9684

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

9685

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers as specified in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

9686

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified s...

Open

9687

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205 and section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

9688

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630 for the product in question, validated by Quality Control and referenced in the relevant specifications and plant documentation. Source: DMV_...

Open

9689

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements, including Charpy V-notch testing at -46°C with specified minimum absorbed energy values and sub-size reduction factors. The pipe dimensions allow both transverse and longitud...

Open

9690

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

9691

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of metallurgical and non...

Open

9692

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the item table and confirmed by the digest. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9693

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 or availability of Qualification Test Records/Manufacturer Procedure Conformity Records. Supplier is only accredited to M-650, not ISO 17782, and required documentation is not c...

Open

9694

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

9695

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9696

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN ≥ 40, as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK ...

Open

9697

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

9698

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produc...

Open

9699

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

9700

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per ASTM A790 and NORSOK r...

Open

9701

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

9702

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

9703

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for 18.26mm wall thickness and 219.1mm OD pipe as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

9704

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not accredited to ISO 17782 as required; no confirmation of QTR/MPCR availability. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9705

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect intermetallic phases, in accordance with ISO 17781, is explicitly required for micrographic examination, fulfilling the requirement for suitable etchant(s) as listed in ISO 17781 Appendix B to show ferrite b...

Open

9706

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

9707

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

9708

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

9709

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

9710

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fulfilled. Source: DMV_STANDARD_...

Open

9711

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

9712

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), matching NORSOK MDS D51 and client ...

Open

9713

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is specified and confirmed for DMV 25.7N as per NORSOK MDS D51 Rev 06 and ISO 17781/ASTM E1245. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

9714

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50°C, 24h) in accordance with ISO 17781 is provided in the referenced documentation or specifications. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9715

4.5

AI

No

add date

DMV 25.7N meets all metallurgical property acceptance criteria (chemical composition, mechanical properties, impact, corrosion, microstructure, ferrite) per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, with mill M-650 qualification up...

Open

9716

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

9717

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712 is provided in the relevant documents. Source: DMV_STANDARD_...

Open

9718

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/1...

Open

9719

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 -...

Open

9720

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/650 are not fully addressed; eddy current testing is not feasible for the required OD, hydrostatic and ultrasonic tests are only available at extra cost, and full-length dye penetrant tes...

Open

9721

5.2

AI

No

add date

No provided documentation explicitly confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that such NDE acceptance criteria are standardly feasible for the requested pipe size at Montb...

Open

9722

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the requested pipe size, with no overriding requirements specified by the customer or drawing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/07-01 - General info...

Open

9723

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9724

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 (§14), requiring full traceability to melt and heat treatment lot. Standard marking methods include heat number and DMV lot number, ensuring compliance for all pipes at the Montbard plant....

Open

9725

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9726

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

9727

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

9728

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demons...

Open

9729

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the product, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-...

Open

9730

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant standards and qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D...

Open

9731

10.2

AI

No

add date

No document provides all required documentation or data such as NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical (ladle) analysis, soluti...

Open

9732

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

9733

3.1

AI

No

add date

AOD or equivalent refining is used and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9734

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN ≥ 40, matching the requirements of Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat as required. Source: 02-03-0...

Open

9735

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Certification will include heat treatment condition ...

Open

9736

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

9737

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

9738

4.1

AI

No

add date

Test sampling for seamless pipes per ASTM A790 and NORSOK MDS D51, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfille...

Open

9739

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

9740

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

9741

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe size and wall thickness (>6mm, 18.26mm) in both longitudinal and transverse directions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructi...

Open

9742

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -466C, with minimum absorbed energy values of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal, including reduction factors for sub-si...

Open

9743

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed according to ISO 17781 with 20-40% NaOH or KOH solution after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

9744

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

9745

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

9746

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9747

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

9748

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

9749

4.4.2

AI

No

add date

Findings of intermetallic stringers must be reported, and acceptance is based on CVN and corrosion test results as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

9750

4.4.2

AI

No

add date

The available specifications allow isolated intermetallic precipitates below 10μm, but do not enforce a complete prohibition of intermetallic phases and/or precipitates if CVN testing cannot be completed, as required by the client specification. Sour...

Open

9751

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

9752

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Acceptance criteria: structure must be basically free from intermetallic precipitates (isolated, non-distr...

Open

9753

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

9754

4.5

AI

No

add date

No explicit confirmation that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9755

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO ...

Open

9756

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A @ 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

9757

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor are their roles and responsibilities as defined in ISO 9712 addressed. Source: DMV_STANDARD_BOOK/12-02-01 - Non d...

Open

9758

5.2

AI

No

add date

100% ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is confirmed for the specified pipe dimensions; calibration is expected to follow ASTM E213 Figure 3 as referenced by the standard. Untested ends will be cut as standard practice, ...

Open

9759

5.2

AI

No

add date

NDE per ASTM A790 and NORSOK M-630 MDS D51 is required, but available documentation only confirms partial NDE capability (hydrostatic, EC, or UT per ASTM A999) and indicates that eddy current and ultrasonic testing for the specified OD are not standa...

Open

9760

5.2

AI

No

add date

No explicit statement that indications greater than the calibration notch are considered defects requiring rejection or repair, and standard NDE methods (e.g., eddy current) are not feasible for the requested OD at the Montbard plant. NDE acceptance ...

Open

9761

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (A790 referencing A999), with no override by TechnipFMC indicated for the specified size and product. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - ...

Open

9762

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9763

8.0

AI

No

add date

Marking per ASTM A790 §16.1 and plant standard practices includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 R...

Open

9764

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9765

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

9766

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

9767

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified ...

Open

9768

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

9769

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant standards and qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D...

Open

9770

10.2

AI

No

add date

No provided documentation includes all required details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or complete metallurgical and non-destructive test...

Open

9771

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as referenced in the item table and confirmed by specification digests. M-650 qualification is also met for the required wall thickness. Sour...

Open

9772

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 or availability of QTR/MPCR documentation; only M-650 accreditation is confirmed, not ISO 17782 as required. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STA...

Open

9773

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

9774

3.1

AI

No

add date

AOD or equivalent refining is standard practice and required for 100% of production; chemical composition complies with Table 2 for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9775

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat, confirming conformity to the requireme...

Open

9776

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

9777

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

9778

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 ...

Open

9779

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specified locations; pi...

Open

9780

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4 as specified in NORSOK MDS D51. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

9781

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 06 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

9782

4.3

AI

No

add date

Charpy V-notch testing is feasible and meets ASTM A370 and ISO 148-1 requirements for the specified pipe dimensions (OD 219.1 mm, WT 18.26 mm). Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-0...

Open

9783

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements at -46°C: minimum 45/35 J (transverse) and 65/50 J (longitudinal) for thickness >6mm. The specified pipe dimensions allow for required impact testing directions and specimen sizes. Sour...

Open

9784

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

9785

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination in accordance with the requirement. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

9786

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

9787

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs are included and recorded as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

9788

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

9789

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions and meets the requirement. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

9790

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

9791

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully fulfilled. Source: DMV_STA...

Open

9792

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

9793

4.4.3

AI

No

add date

Microstructure examination is performed as per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Structure must be basically free from intermetallic precipitates (isolated precipitates allowed if no...

Open

9794

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9795

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9796

4.5

AI

No

add date

DMV 25.7N complies with all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

9797

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

9798

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source: DM...

Open

9799

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed on the required pipe dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testin...

Open

9800

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not validated. Available documents confirm NDE per ASTM A790/A999 but do not address NORSOK-specific requirements. For the specified OD, eddy current testing is not...

Open

9801

5.2

AI

No

add date

No explicit confirmation that NDE acceptance criteria require rejection or repair of indications greater than the calibration notch; feasibility for required NDE is not confirmed for the specified dimension at Montbard. Source: DMV_STANDARD_BOOK/02-0...

Open

9802

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790 referencing ASTM A999) for the requested pipe size, with no overriding tolerances specified in the customer request or TechnipFMC documentation. Source: 07.01 - General informatio...

Open

9803

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9804

8.0

AI

No

add date

Marking per ASTM A790 and plant marking methods ensure mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDA...

Open

9805

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

9806

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

9807

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

9808

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

9809

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications and plant certification procedures. Source: DMV_STANDARD_BOOK/02-...

Open

9810

10.2

AI

No

add date

Required documentation and data such as NORSOK M-650/ISO 17782 identification, steel producer, steel melting practice, heat number, chemical analysis, solution annealing details, and results of all metallurgical and non-destructive testing are not pr...

Open

9811

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

9812

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence provided for full qualification to both NORSOK M-650/ISO 17782 or availability of QTR/MPCR for review as required by the specifi...

Open

9813

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, with manufacturing process qualified per NORSOK M-650 (or ISO 17782), and compliance with NORSOK M-630 MDS D51 Rev. 6 is confirmed. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

9814

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9815

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PREN ≥ 40, as specified for ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9816

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

9817

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

9818

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9819

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ...

Open

9820

4.1

AI

No

add date

Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions, are fulfilled for DM...

Open

9821

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 as required for DMV 25.7N seamless pipe per NORSOK MDS D51 and ASTM A790. Source: DMV_STANDARD...

Open

9822

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

9823

4.3

AI

No

add date

Pipe wall thickness exceeds minimum required for Charpy V-notch testing per ASTM A370 and ISO 148-1; testing is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

9824

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements (Charpy V-notch at -46°C: transverse 45J/35J, longitudinal 65J/50J, sub-size reduction factors). The specified pipe dimensions allow for required transverse and longitudinal t...

Open

9825

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

9826

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is explicitly required and matches the specification requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

9827

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

9828

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

9829

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

9830

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

9831

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size. No other provided information addresses this r...

Open

9832

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

9833

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive, micrographic, corrosion tests, ferrite content, heat treatment, and manufacturing process requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest...

Open

9834

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallics, isolated precipitates <10µm, carbides/nitrides reported), with acceptance b...

Open

9835

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

9836

4.5

AI

No

add date

No explicit evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or referenced in the provided documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9837

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORS...

Open

9838

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

9839

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

9840

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed on the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

9841

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD, eddy current testing is not feasible, and hydrostatic or ultras...

Open

9842

5.2

AI

No

add date

No provided documentation explicitly states that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, and standard NDE methods are not feasible for the requested OD at Montbard. Source:...

Open

9843

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A ...

Open

9844

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: ASTM A 790.docx, NORSOK MDS D51 Rev 06.docx

Open

9845

8.0

AI

No

add date

Marking is performed according to ASTM A790, requiring full traceability to melt and heat treatment lot, with mandatory marking of heat number and DMV lot number using approved methods. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

9846

9.0

AI

No

add date

Weld repairs are explicitly stated as not acceptable for DMV 25.7N in the specification under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-...

Open

9847

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

9848

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

9849

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, and QTR number is included as per M-650 qualification, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MCPR...

Open

9850

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products being delivered as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dige...

Open

9851

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference). ...

Open

9852

10.2

AI

No

add date

Most documentation and certification requirements are addressed except for the 'Steel producer of the starting material,' which is not fully fulfilled as only the country of origin is provided, not the specific producer. No source provides all requir...

Open

9853

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the item table and confirmed by the digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-0...

Open

9854

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9855

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

9856

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9857

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9858

3.2

AI

No

add date

Pipes are solution annealed followed by water quenching per ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650/ISO 17782, and proper pipe placement during heat treatment is ensured. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

9859

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for one set per heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

9860

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

9861

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations, in compliance with ASTM A790 and NORSOK M...

Open

9862

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9863

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with mechanical properties and maximum hardness meeting Table 4 requirements for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

9864

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

9865

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for 18.26mm wall thickness and 219.1mm OD pipe as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impac...

Open

9866

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, including minimum absorbed energy values for both transverse and longitudinal directions, sub-size specimen reduction factors, and testing procedures. The specified ...

Open

9867

4.4.1

AI

No

add date

Micrographic examination is performed in accordance with ISO 17781, with specified etchants (20-40% NaOH or KOH for intermetallics, 10% oxalic acid or V2A followed by 20-40% NaOH or KOH for nitrides/carbides) after final polishing, fulfilling the req...

Open

9868

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination and matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

9869

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

9870

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

9871

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOO...

Open

9872

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

9873

4.4.2

AI

No

add date

No document guarantees that intermetallic phases and/or precipitates are completely prohibited if CVN testing cannot be completed; the closest specification allows isolated precipitates below 10µm, which does not meet the zero-tolerance requirement. ...

Open

9874

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

9875

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

9876

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

9877

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or documented. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9878

4.5

AI

No

add date

Corrosion test for DMV 25.7N is performed per ISO 17781: G48 Method A at 50°C for 24 hours, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and DMV 25.7N complies with these requirements. Source: DMV_STANDARD_B...

Open

9879

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

9880

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed on the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

9881

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not addressed in the available documentation. For the requested OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only availab...

Open

9882

5.2

AI

No

add date

The requirement that any indication greater than the calibration notch is a defect and must be rejected or repaired is not explicitly stated or confirmed in the referenced specifications and NDE feasibility documents. Standard NDE for OD 219.1 mm is ...

Open

9883

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790/A999) for the specified product, with no overriding requirements stated by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK...

Open

9884

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9885

8.0

AI

No

add date

Marking is performed per ASTM A790 §14 and includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02...

Open

9886

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

9887

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

9888

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

9889

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification de...

Open

9890

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to delivered products, fulfilling the documentation and traceability requirements for TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

9891

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

9892

10.2

AI

No

add date

No provided documentation includes all required details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all required meta...

Open

9893

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, testing, and qualification requirements. Manufacturing is M-650 qualified for the specified wall thickness, and all relev...

Open

9894

1.0

AI

No

add date

Supplier is M-650 accredited for UNS S32760/DMV25.7N up to WT = 31.75 mm but is not accredited to ISO 17782, so the requirement for NORSOK M-650/ISO 17782 qualification is not fulfilled. No evidence of QTR/MPCR availability is provided. Source: DMV_S...

Open

9895

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

9896

3.1

AI

No

add date

AOD or equivalent refining is used for DMV 25.7N, and chemical analysis complies with the specified requirements in Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9897

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the requirement table and DMV material composition conforms to this specification with heat analysis and supplier certification provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

9898

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650/ISO 17782. Proper heat treatment and free circulation during processing are ensur...

Open

9899

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

9900

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

9901

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specifi...

Open

9902

4.2

AI

No

add date

Tensile testing is performed at room temperature per required standards, with mechanical properties and hardness meeting Table 4 and NORSOK MDS D51 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

9903

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

9904

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 and ISO 148-1 is feasible for the specified pipe dimensions, as the wall thickness exceeds the minimum required for both standards. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

9905

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for required transverse testing. Source: D...

Open

9906

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

9907

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

9908

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

9909

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

9910

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

9911

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

9912

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size. The requirement is not fully fulfilled....

Open

9913

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

9914

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with required etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requirement fo...

Open

9915

4.5

AI

No

add date

Applicable standards are referenced but there is no explicit confirmation that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or fulfilled. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montba...

Open

9916

4.5

AI

No

add date

DMV 25.7N complies with all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

9917

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

9918

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructiv...

Open

9919

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is confirmed for the specified pipe dimensions, and calibration procedures are expected to follow ASTM E213, including reference notches as required. Source: DMV_STANDARD_...

Open

9920

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

9921

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790, NORSOK M-630 MDS D51 Rev 6, and NORSOK M-650/ISO 17782 are not fully addressed. Available documentation confirms only standard hydrostatic or NDE (EC/UT) per ASTM A999, with no explicit evidence for NORSOK-speci...

Open

9922

5.2

AI

No

add date

None of the reviewed documents confirm that NDE acceptance criteria require any indication greater than the calibration notch to be treated as a defect and rejected or repaired; there is also no confirmation that the required NDE will be performed as...

Open

9923

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding TechnipFMC specification indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A 376-0...

Open

9924

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9925

8.0

AI

No

add date

Marking per ASTM A790 ensures full traceability to melt and heat treatment lot, with standard marking methods including heat number and lot number as required for compliance with the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK M...

Open

9926

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

9927

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

9928

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-...

Open

9929

10.1

AI

No

add date

Certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified ...

Open

9930

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

9931

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications and plant documentation. Source: DMV_STANDARD_BOOK/02-04-03 - Dig...

Open

9932

10.2

AI

No

add date

Most documentation and certification requirements are addressed except for the 'Steel producer of the starting material,' which is not fully met as only the country of origin is provided, not the specific producer. All other requirements are stated t...

Open

9933

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification digest and the customer specification listing 'A790 NORSOK'. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev...

Open

9934

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; full qualification per NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR is not confirmed. Source: DMV_STANDARD_BOOK/0...

Open

9935

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits specified in Table 2, including PREN ≥ 40, as required by ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9936

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

9937

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with lot defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

9938

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and direct reference to the table for test specimen sampling as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

9939

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled. For the ordered pipe (OD 219.1 ...

Open

9940

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1 at room temperature, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

9941

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

9942

4.3

AI

No

add date

Charpy V-notch testing is feasible and the requirement is fulfilled for the specified pipe dimensions according to ASTM A370 and ISO 148-1 minimum wall thickness criteria. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-...

Open

9943

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C (transverse: avg 45 J, single 35 J; longitudinal: avg 65 J, single 50 J if transverse not possible). The specified pipe dimensions allow for required transverse and l...

Open

9944

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with etchants (20-40% NaOH or KOH, 10% oxalic acid or V2A followed by NaOH/KOH) used after final polishing as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

9945

4.4.1

AI

No

add date

Etching with 20–40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

9946

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and if each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

9947

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

9948

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

9949

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9950

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

9951

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

9952

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

9953

4.4.3

AI

No

add date

Micrographic examination per ISO 17781 is specified, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impact ...

Open

9954

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9955

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

9956

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties, including destructive, corrosion, micrographic tests, and ferrite content, as required by NORSOK MDS D51 Rev 06, ASTM A790, and NORSOK M-650/ISO 17782 for the specified wall thickn...

Open

9957

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

9958

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

9959

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed on the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

9960

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD, eddy current testing is not feasible, and hydrostatic or ultras...

Open

9961

5.2

AI

No

add date

None of the relevant documents explicitly confirm that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair of pipe/tubing, nor do they confirm this acceptance criterion is applied as...

Open

9962

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no alternative tolerances specified by TechnipFMC. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according ...

Open

9963

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be pickled or bright annealed, directly fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

9964

8.0

AI

No

add date

Marking is per ASTM A790 and includes heat number and lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standard mar...

Open

9965

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

9966

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

9967

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

9968

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

9969

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products being delivered as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

9970

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 manufacturing summary/QTR number. Source: DMV_ST...

Open

9971

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or complete metallurgical and non-dest...

Open

9972

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 -...

Open

9973

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; full qualification to NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR is not confirmed for review by TechnipFMC as r...

Open

9974

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N with the requested wall thickness within the qualified range, and manufacturing is according to M-650 (or ISO 17782) qualified procedures with testing per NORSOK M-630 MDS D51 rev. 6. Source: DMV_STA...

Open

9975

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9976

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PRE ≥ 40, matching the requirements of Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat as required. Source: 02-03-01...

Open

9977

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N, and certification will state heat treatment per ASTM ...

Open

9978

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, with test frequency specified as '1/lot'. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

9979

4.1

AI

No

add date

Test specimen sampling is defined in Table 3, with tensile test frequency specified as 1 per 100 pieces and per lot, in accordance with ASTM A790 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/0...

Open

9980

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, in compliance with ASTM A790 an...

Open

9981

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

9982

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

9983

4.3

AI

No

add date

Charpy V-notch testing in accordance with ASTM A370 and ISO 148-1 is feasible for the specified pipe dimensions and can be performed as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03...

Open

9984

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal if transverse is not possible. The specified pipe dimensions allow...

Open

9985

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

9986

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution for detecting ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

9987

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

9988

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

9989

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

9990

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

9991

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

9992

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly prohibits weld repairs under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

9993

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781...

Open

9994

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

9995

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

9996

4.5

AI

No

add date

ASTM G48 Method 'A' corrosion testing at 50°C for 24h in accordance with ISO 17781 is not explicitly mentioned or confirmed; compliance cannot be verified based on the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Mo...

Open

9997

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties as specified in NORSOK MDS D51 Rev 06, including destructive, micrographic, ferrite, corrosion tests, heat treatment, and manufacturing process requirements. Source: DMV_STANDARD_BO...

Open

9998

4.5

AI

No

add date

Requirement for no pitting at 20X magnification and weight loss less than 1.0 g/m² is met by compliance with ISO 17781: G48 Method A @ 50°C for 24 hours, as specified for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

9999

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

10000

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed on the required dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultrasonic testing/12-02-03 - Ultrasonic...

Open

10001

5.2

AI

No

add date

NDE per ASTM A790 is generally feasible, but NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782-specific NDE requirements are not validated. For the requested OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only...

Open

10002

5.2

AI

No

add date

No provided document explicitly confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that NDE is performed as standard for the requested dimension at Montbard. Source: DMV_STANDARD_BOO...

Open

10003

6.0

AI

No

add date

Dimensional tolerances for the specified pipe are per the applicable ASTM standard (ASTM A790 referencing ASTM A999), with no evidence of override in the customer specification. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_...

Open

10004

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10005

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

10006

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10007

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

10008

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

10009

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

10010

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to products, fulfilling the requirement for documentation to be transmitted to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

10011

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

10012

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and results of all metallurgical and non-...

Open

10013

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification and referenced documentation. Manufacturing is M-650 qualified and all relevant mechanical, chemical, and testing requirement...

Open

10014

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782, which is explicitly required. No evidence of QTR/MPCR documentation availability. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10015

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

10016

3.1

AI

No

add date

AOD or equivalent refining is used and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10017

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis is performed per heat and matches the required limits for all elements listed in the requ...

Open

10018

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

10019

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

10020

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ...

Open

10021

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, in compliance with ASTM A790 an...

Open

10022

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, meeting the tensile and maximum hardness properties of Table 4 for DMV 25.7N (UNS S32760), as required by NORSOK MDS D51. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

10023

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

10024

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for wall thickness >6mm in both longitudinal and transverse directions for the specified dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing...

Open

10025

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements, including Charpy V-notch testing at -46°C with minimum absorbed energy values (transverse: 45 J average/35 J single, longitudinal: 65 J average/50 J single if transverse not ...

Open

10026

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

10027

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

10028

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

10029

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

10030

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

10031

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

10032

4.4.2

AI

No

add date

The available specifications allow isolated intermetallic precipitates below 10μm, but do not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed, as required by the client. Zero-tolerance is not guaranteed by t...

Open

10033

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

10034

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosio...

Open

10035

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) performed in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

10036

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, microstructure, solution annealing, ferrite content, absence of intermetallics, and required certifications and qualificati...

Open

10037

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02...

Open

10038

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

10039

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within the machine's capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive...

Open

10040

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782 NDE requirements are addressed. For the specified OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/ultrasonic tests...

Open

10041

5.2

AI

No

add date

None of the reviewed documents explicitly confirm that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair; NDE acceptance criteria based on calibration notch are not specified, and ...

Open

10042

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790 referencing ASTM A999), with no other specifications overriding this requirement for the requested product dimensions. Source: DMV_STANDARD_BOOK/07-01 - General in...

Open

10043

7.0

AI

No

add date

ASTM A790 (6.1.3) and NORSOK MDS D51 (§13) both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10044

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/1...

Open

10045

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10046

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

10047

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

10048

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

10049

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfilled for the specified pipe dimensions according to ASTM A370 and ISO 148-1 requirements for minimum wall thickness. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Imp...

Open

10050

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

10051

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications and documentation scope. Source: DMV_STANDARD_BOOK/02-04-03 - Dig...

Open

10052

10.2

AI

No

add date

Most required documentation and certification items (NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and test results) are either not provided ...

Open

10053

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification listing and digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Norms / Customer Specifications...

Open

10054

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR availability as required. Requirement for qualification to both NORSOK M-650/ISO 17782 and documentation availability is not fulfilled...

Open

10055

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

10056

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10057

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed to be fulfilled by supplier certification and heat analysis per ASTM A790 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

10058

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

10059

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined by ASTM A790, fulfilling the requirement for DMV 25.7N seamless duplex pipe. Source: DMV_STANDARD_BOOK/02...

Open

10060

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling as specified in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

10061

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions, is fulfilled for DMV 25.7N. The or...

Open

10062

4.2

AI

No

add date

Tensile and hardness testing are performed per ASTM A790, which requires mechanical testing in accordance with ASTM A370, and the material meets the specified tensile and hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

10063

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

10064

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible), with reduction factors for sub-size...

Open

10065

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

10066

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

10067

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

10068

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

10069

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with representative micrographs recorded and reported at actual magnification and including a scale bar if intermetallic phases are not detected, at or near mid-wall thickness....

Open

10070

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NO...

Open

10071

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

10072

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

10073

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

10074

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

10075

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified per NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

10076

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

10077

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

10078

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/1...

Open

10079

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT) is detailed, but there is no explicit confirmation of compliance with NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782 acceptance criteria. For the specified OD, Eddy current testing is not feasible, and ...

Open

10080

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair; NDE acceptance criteria per the client specification are not validated for the requested product and...

Open

10081

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are confirmed to be per the applicable ASTM standard (ASTM A999), with no deviations or overrides specified in the customer requirements. OD, WT, and ovality tolerances for the relevant dimensio...

Open

10082

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10083

8.0

AI

No

add date

Marking is performed according to ASTM A790, requiring full traceability to melt and heat treatment lot, with mandatory marking of heat number and DMV lot number ensuring compliance with the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NO...

Open

10084

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10085

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

10086

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dige...

Open

10087

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness as required for qualification demonstration for the size...

Open

10088

10.2

AI

No

add date

ISO 9001 certification and EN 10204 Type 3.1/3.2 certificates are provided, ensuring documentation is traceable to delivered products and meets SIR205 requirements for TechnipFMC. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

10089

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAN...

Open

10090

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the actual steel producer name. Other requir...

Open

10091

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all standard and supplementary requirements, and are M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-...

Open

10092

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided; only 'A790 NORSOK' is referenced in the specifications. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

10093

1.0

AI

No

add date

No evidence of supplier qualification to NORSOK M-650/ISO 17782 or availability of Qualification Test Records (QTR/MPCR); ISO 17782 accreditation is missing for the supplier mentioned. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_...

Open

10094

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, fulfilling the requirement for manufacturer and process qualification and compliance with ...

Open

10095

3.1

AI

No

add date

AOD or equivalent steel refining is required for 100% of production and DMV 25.7N complies with the chemical composition requirements per Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

10096

3.1

AI

No

add date

Chemical composition for S32760 matches Table 2 of ASTM A790 as required, and DMV material conforms with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-0...

Open

10097

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

10098

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is carried out for each heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

10099

4.1

AI

No

add date

Test specimens sampling is performed according to Table 3, with specified frequency for tensile tests, directly referencing the required sampling method. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-0...

Open

10100

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled per NORSOK MDS D51/ASTM A790. T...

Open

10101

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

10102

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets the minimum requirements: yield strength ≥ 550 MPa, tensile strength ≥ 750 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 -...

Open

10103

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for 18.26mm wall thickness and 219.1mm OD pipe as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impac...

Open

10104

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if transverse...

Open

10105

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

10106

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

10107

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

10108

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

10109

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

10110

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

10111

4.4.2

AI

No

add date

Findings of intermetallic stringers must be reported, and acceptance is based on CVN and corrosion test results as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

10112

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Zero-tolerance ...

Open

10113

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

10114

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching methods, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requirement for...

Open

10115

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

10116

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

10117

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

10118

4.5

AI

No

add date

DMV 25.7N meets the pitting corrosion test per ISO 17781: G48 Method A at 50°C for 24h, with no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

10119

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

10120

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed on the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - U...

Open

10121

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not addressed or validated. Only general ASTM A790/ASTM A999 NDE (hydrostatic, EC, UT) is confirmed, but NORSOK-specific requirements are not demonstrated. For the ...

Open

10122

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10123

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor is there confirmation that the required NDE will be performed as standard for the specifie...

Open

10124

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 seamless pipe are confirmed to be per the applicable ASTM standard (ASTM A999), with no overriding customer specification or drawing indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDA...

Open

10125

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10126

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

10127

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

10128

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

10129

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

10130

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

10131

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

10132

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630 for 25Cr Duplex Stainless Steel seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-0...

Open

10133

10.2

AI

No

add date

Most documentation and certification requirements are addressed, but the specific steel producer of the starting material is not provided (only country of origin is given). Actual documentation for the specific batch, including NORSOK M-650/ISO 17782...

Open

10134

1.0

AI

No

add date

DMV 25.7N (UNS S32760) is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

10135

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782, and there is no evidence that QTR/MPCR documentation is available for review as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

10136

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

10137

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10138

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat, confirming conformity to the requireme...

Open

10139

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

10140

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for each heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

10141

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

10142

4.1

AI

No

add date

DMV 25.7N seamless pipes are tested per NORSOK MDS D51/ASTM A790 requirements, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure at specified locations. For the s...

Open

10143

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 ...

Open

10144

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

10145

4.3

AI

No

add date

Charpy V-notch testing is feasible and the requirement is fulfilled as the pipe wall thickness exceeds the minimum required for testing according to ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/1...

Open

10146

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements, including Charpy V-notch testing at -46°C with minimum absorbed energy values (transverse: 45 J avg/35 J single, longitudinal: 65 J avg/50 J single) and sub-size reduction factors. The...

Open

10147

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants after final polishing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

10148

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

10149

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

10150

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs are included and recorded as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

10151

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

10152

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

10153

4.4.2

AI

No

add date

No evidence that intermetallic phases and/or precipitates are completely prohibited if CVN testing cannot be completed; isolated precipitates are allowed in the referenced specification, which does not fully meet the requirement. Source: DMV_STANDARD...

Open

10154

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

10155

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corro...

Open

10156

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

10157

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation or standards list. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

10158

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO ...

Open

10159

4.5

AI

No

add date

Requirement for no pitting at 20X magnification and weight loss less than 1.0 g/m² is met by compliance with ISO 17781: G48 Method A, as specified for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

10160

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

10161

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed on the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - U...

Open

10162

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT at 100%) is confirmed, but there is no evidence of compliance with the more stringent NDE requirements of NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782. Eddy current testing is not feasible for the requ...

Open

10163

5.2

AI

No

add date

No provided documentation explicitly states that any indication greater than the calibration notch is considered a defect requiring rejection or repair, and standard NDE methods (e.g., Eddy current) are not feasible for the requested OD at Montbard, ...

Open

10164

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed as per ASTM A790 and referenced ASTM A999 for the specified size, with no overriding TechnipFMC requirements indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDA...

Open

10165

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10166

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot; marking methods (indelible ink, vibro-etching) include heat and lot numbers as standard practice. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx,...

Open

10167

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA and specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

10168

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

10169

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demonstration for th...

Open

10170

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

10171

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and will include all information required by ASTM A790 and NORSOK M-630, with issuance and validation by Quality Control. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, 14-03 - Certification Montbard...

Open

10172

10.2

AI

No

add date

No documentation or certification is provided that confirms NORSOK M-650/ISO 17782 identification, QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, ladle chemical analysis, solution annealing temperature, hold...

Open

10173

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/...

Open

10174

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10175

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N within the required wall thickness range, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_...

Open

10176

3.1

AI

No

add date

AOD or equivalent steel refining is required for 100% of production, and the chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 ...

Open

10177

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed by supplier certification and heat analysis for DMV material. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

10178

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

10179

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, with test frequency '1/lot' referenced to the relevant standards. Source: DMV_STANDARD_BOOK...

Open

10180

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-0...

Open

10181

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, fulfilling NORSOK MDS D51/ASTM...

Open

10182

4.2

AI

No

add date

Tensile testing is performed in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 as required for DMV 25.7N (UNS S32760). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

10183

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW, as specified in Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

10184

4.3

AI

No

add date

Charpy V-notch testing in accordance with ASTM A370 and ISO 148-1 is feasible for the specified pipe dimensions and can be performed as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03...

Open

10185

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C: transverse (average 45 J, single 35 J), longitudinal (average 65 J, single 50 J if transverse not possible); pipe wall thickness allows required testing orientation ...

Open

10186

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

10187

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

10188

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

10189

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

10190

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

10191

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

10192

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_BOOK/0...

Open

10193

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

10194

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

10195

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching methods, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact...

Open

10196

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in accordance with ISO 17781 and ASTM E1245, and compliance for DMV 25.7N is confirmed. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04...

Open

10197

4.5

AI

No

add date

No explicit evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or referenced in the provided documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

10198

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORS...

Open

10199

4.5

AI

No

add date

DMV 25.7N undergoes pitting corrosion testing per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD...

Open

10200

5.1

AI

No

add date

No evidence is provided confirming NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor are their roles and responsibilities defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non dest...

Open

10201

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

10202

5.2

AI

No

add date

NDE per ASTM A790 (100% hydrostatic or EC/UT) is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE acceptance criteria are addressed. For the requested OD (219.1 mm), standard NDE is not availa...

Open

10203

5.2

AI

No

add date

No provided documentation explicitly confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that NDE is performed as standard for the requested pipe size and specification. Relevant acce...

Open

10204

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standards (ASTM A999), with no override by TechnipFMC in the provided context. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances ac...

Open

10205

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORS...

Open

10206

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods include heat number and DMV lot number, ensuring compliance with the requirement for traceability. Source: DMV_...

Open

10207

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10208

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

10209

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10210

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

10211

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified s...

Open

10212

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03...

Open

10213

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

10214

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice, heat number, chemical analysis, solution annealing temperature/holding time/quench medium, and ...

Open

10215

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all relevant chemical, mechanical, manufacturing, and testing requirements, and are M-650 qualified up to the required wall thickness. Source: DMV_...

Open

10216

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782, and there is no confirmation of Qualification Test Record (QTR/MPCR) availability as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

10217

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

10218

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10219

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN ≥ 40, matching the requirements of Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat as required. Source: DMV_STA...

Open

10220

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

10221

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

10222

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

10223

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, in accordance with NORSOK MDS D...

Open

10224

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with material meeting the tensile and maximum hardness properties of Table 4 for DMV 25.7N (UNS S32760), as required by NORSOK MDS D51. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

10225

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

10226

4.3

AI

No

add date

Charpy V-notch testing in accordance with ASTM A370 and ISO 148-1 is feasible for the specified pipe dimensions and can be performed as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03...

Open

10227

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible). The specified pipe dimensions allow ...

Open

10228

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

10229

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

10230

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

10231

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

10232

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

10233

4.4.2

AI

No

add date

Micrographic examination requires reporting of centerline intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

10234

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases/precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not fully met. So...

Open

10235

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

10236

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

10237

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

10238

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

10239

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours is performed on DMV 25.7N, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and DMV 25.7N complies with these requirements. Source: DMV_STANDARD_BO...

Open

10240

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

10241

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

10242

5.2

AI

No

add date

NDE per ASTM A790 is partially addressed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE acceptance criteria are fulfilled. For the requested OD, eddy current testing is not feasible, and hydr...

Open

10243

5.2

AI

No

add date

None of the relevant documents explicitly confirm that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, nor do they detail the required acceptance criteria for NDE indications as sp...

Open

10244

6.0

AI

No

add date

Dimensional tolerances for the specified pipe are per the applicable ASTM standard (ASTM A790/A999) as required, with no overriding TechnipFMC specification identified. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-0...

Open

10245

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10246

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and standard practice at Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_S...

Open

10247

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

10248

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

10249

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

10250

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, fulfilling the qualification requirement for the specified size and product f...

Open

10251

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

10252

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

10253

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 in the provided documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

10254

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or complete metallurgical and NDT test...

Open

10255

1.0

AI

No

add date

DMV 25.7N seamless pipe is compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest...

Open

10256

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10257

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

10258

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis for DMV 25.7N is compliant with Table 2 requirements. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10259

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements, and heat analysis is performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A...

Open

10260

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

10261

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

10262

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, directly referencing Table 3 for test specimen sampling as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02...

Open

10263

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not feasible), and corrosion/microstructure tests, with specified locations and directions, is fulfilled for DMV 25.7N per ...

Open

10264

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

10265

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

10266

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions (WT 18.26mm), fulfilling the requirement for wall thickness >6mm in both longitudinal and transverse directions as per standards. Source: DMV...

Open

10267

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

10268

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements: Charpy V-notch testing at -466C, minimum absorbed energies of 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible), ...

Open

10269

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants after final polishing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

10270

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

10271

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

10272

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs are included as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

10273

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

10274

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

10275

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

10276

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

10277

4.4.3

AI

No

add date

Microstructure examination per ISO 17781 is specified, including etching, magnification, and acceptance criteria (free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requirement for micrograp...

Open

10278

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met by DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10279

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or mentioned in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

10280

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORS...

Open

10281

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², which DMV 25.7N complies with. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

10282

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

10283

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

10284

5.2

AI

No

add date

100% of pipes are subject to hydrostatic or nondestructive electric (EC/UT) testing as per ASTM A999, fulfilling standard NDE requirements for seamless duplex stainless steel pipe per ASTM A790 and NORSOK M-630 MDS D51. Source: DMV_STANDARD_BOOK/02 -...

Open

10285

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect and that such pipe or tubing shall be rejected or repaired, as required by the specification. NDE feasibility for ...

Open

10286

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no evidence of a deviation or override in the customer specification or TechnipFMC documentation. Source: DMV_STANDARD_BOOK/07-01 - General...

Open

10287

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be pickled or bright annealed, fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10288

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

10289

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10290

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

10291

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

10292

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

10293

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

10294

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

10295

10.2

AI

No

add date

Documentation and certification details required by the specification—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of ...

Open

10296

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

10297

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified up to the required wall thickness. Source: DMV...

Open

10298

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; full qualification to NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR is not confirmed. Source: DMV_STANDARD_BOOK/02...

Open

10299

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

10300

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10301

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 06, including PREN calculation and all element limits for S32760. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - D...

Open

10302

3.2

AI

No

add date

DMV 25.7N pipes are solution annealed followed by water quenching per ASTM A790, with manufacturing process qualified to NORSOK M-650, and pipes are arranged to ensure free circulation of heating and cooling media during heat treatment including acce...

Open

10303

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

10304

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, fulfilling the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed ...

Open

10305

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations a...

Open

10306

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 as required for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

10307

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

10308

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

10309

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C, with minimum absorbed energy values for both transverse and longitudinal directions. The specified pipe dimensions allow for both test orientations, fulfilling the r...

Open

10310

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

10311

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination of the material, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

10312

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

10313

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are reported with representative micrographs showing the presence and location of intermetallic phases. S...

Open

10314

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

10315

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_ST...

Open

10316

4.4.2

AI

No

add date

No provided documentation confirms a zero-tolerance policy for intermetallic phases and/or precipitates when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10μm, which does not meet the stricter client requi...

Open

10317

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

10318

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

10319

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

10320

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

10321

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spe...

Open

10322

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

10323

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

10324

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

10325

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/ISO 17782 are not fully met: eddy current testing is not feasible for OD 219.1 mm at Montbard, hydrostatic and ultrasonic tests are only available at extra cost, and full-length dye penet...

Open

10326

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot; standard marking methods (indelible ink, vibro-etching) include heat and lot numbers as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx,...

Open

10327

5.2

AI

No

add date

None of the relevant documents explicitly confirm that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, nor do they confirm that NDE with this acceptance criterion is performed as s...

Open

10328

6.0

AI

No

add date

Dimensional tolerances are specified as per the applicable ASTM standard (ASTM A790/A999) for the product, with no overriding TechnipFMC specification referenced, fulfilling the requirement. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, ...

Open

10329

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10330

8.0

AI

No

add date

Marking per ASTM A790 includes heat and lot numbers, and standard marking methods (indelible ink, vibro-etching) at Montbard plant ensure full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev...

Open

10331

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

10332

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

10333

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

10334

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

10335

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

10336

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing the relevant standards and quality system. Source: DMV_STANDARD_BOOK/02-04-03 - Dig...

Open

10337

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis, solution annealing temperature/holding ti...

Open

10338

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/...

Open

10339

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability for review is provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

10340

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

10341

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as specified in Table 2. Heat analysis and supplier certification are performed per heat, confirming conformity to the standard for S32760. Source: 02-03...

Open

10342

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

10343

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with frequency '1/lot' and lot defined per ASTM A790 §9.1, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02...

Open

10344

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling as outlined in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

10345

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, all in accordance with NORSOK ...

Open

10346

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Hardness testing is also performed as specified. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

10347

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 06 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

10348

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, fulfilling the requirement for both longitudinal and transverse directions. Source: DMV_STANDARD_BOOK/12 - Special Testin...

Open

10349

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible), with sub-size reduction factors. The specifi...

Open

10350

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

10351

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination and matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

10352

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

10353

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases. Source: DMV_STANDARD_BOOK/02...

Open

10354

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

10355

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

10356

4.4.2

AI

No

add date

No provided document fully prohibits intermetallic phases and/or precipitates when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10μm, which does not meet the stricter client requirement of absolute absence...

Open

10357

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

10358

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impa...

Open

10359

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS ...

Open

10360

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

10361

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, as well as manufacturing, heat treatment, and qualification requirements. S...

Open

10362

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

10363

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

10364

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is confirmed for the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12...

Open

10365

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT) is detailed, but there is no explicit confirmation of compliance with NORSOK M-630 MDS D51, NORSOK M-650/ISO 17782 NDE requirements. For the specified OD (219.1 mm), eddy current testing is not feasible...

Open

10366

5.2

AI

No

add date

No provided document explicitly states that any indication greater than the calibration notch is considered a defect requiring rejection or repair, and for the requested dimension, standard NDE methods are either not feasible or require extra cost at...

Open

10367

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per ASTM A790 and referenced ASTM A999 for seamless pipe, with no overriding specifications from TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances...

Open

10368

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be pickled or bright annealed, fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10369

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

10370

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

10371

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, fulfilling the qualification requirement. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

10372

10.2

AI

No

add date

No provided document confirms that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205; only general certification and documentation practices are described without explicit compliance to this requirement. ...

Open

10373

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - ...

Open

10374

10.2

AI

No

add date

Required documentation such as NORSOK M-650/ISO 17782 identification, steel producer, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive testing are not provided. Only general practices...

Open

10375

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured and tested in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with all supplementary requirements and M-650 qualification addressed. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

10376

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782, as required. No confirmation of QTR/MPCR availability for review. Requirement not fully fulfilled for both standards and documentation access...

Open

10377

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, fulfilling the requirement for manufacturer and process qualification and compliance with ...

Open

10378

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev...

Open

10379

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition requirements, including PREN ≥ 40, per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10380

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

10381

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

10382

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

10383

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions, is fulfilled for DMV 25.7N. The or...

Open

10384

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

10385

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW, as specified by the client. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

10386

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

10387

4.3

AI

No

add date

DMV 25.7N meets the NORSOK MDS D51 Rev 06 impact test requirements: Charpy V-notch at -46°C, minimum 45 J average and 35 J single (transverse), 65 J average and 50 J single (longitudinal if transverse not possible), with reduction factors for sub-siz...

Open

10388

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

10389

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

10390

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and if each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

10391

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included with presence and location of intermetallic phases noted and recorded. Source: DMV_STANDA...

Open

10392

4.4.2

AI

No

add date

Micrographs at a minimum magnification of 400x are included, reported at actual magnification with a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

10393

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

10394

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

10395

4.4.3

AI

No

add date

Ferrite content is determined per ASTM E1245 (default) or ASTM E562 (on request), performed in accordance with ISO 17781, fulfilling the requirement for ferrite content determination methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

10396

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

10397

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in accordance with ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

10398

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

10399

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02...

Open

10400

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

10401

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is confirmed after all processing, and machine capabilities cover the required dimensions. Calibration procedures are expected to follow ASTM E213, including reference not...

Open

10402

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed; only ASTM A790/A999 NDE is detailed. For the requested OD (219.1 mm), eddy current and ultrasonic testing are not standard and require extra cost or techni...

Open

10403

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor that NDE to this criterion is standard or feasible for the requested dimension at Montbard. Sour...

Open

10404

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A ...

Open

10405

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10406

8.0

AI

No

add date

Marking is per ASTM A790 and includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_ST...

Open

10407

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

10408

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

10409

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

10410

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, and QTR number is included as per M-650 qualification, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MCPR ...

Open

10411

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products as required by SIR205 and section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

10412

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS...

Open

10413

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 ...

Open

10414

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 qualification identification, steel producer, steel melting practice and refining method, heat number, chemical analysis (ladle analysis), solution annealing parameters, or results of all required me...

Open

10415

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 -...

Open

10416

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782, as required. No evidence provided for availability of QTR/MPCR for review by TechnipFMC. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

10417

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

10418

3.1

AI

No

add date

AOD or equivalent steel refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10419

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. The chemical composition table in the requirement matches the standard for S32760, and compliance is confirme...

Open

10420

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

10421

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

10422

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, directly referencing Table 3 for test specimen sampling as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02...

Open

10423

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness l...

Open

10424

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with mechanical properties meeting Table 4 requirements; hardness testing is also performed and results are provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

10425

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

10426

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfills the requirement as the pipe wall thickness exceeds the minimum required for testing per ASTM A370 and ISO 148-1 (striker radius 8 mm). Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive ...

Open

10427

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for required testing directions and specimen sizes. S...

Open

10428

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants and electrolytic etching after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/...

Open

10429

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is explicitly required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_...

Open

10430

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

10431

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

10432

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

10433

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

10434

4.4.2

AI

No

add date

No provided documentation fully prohibits intermetallic phases and/or precipitates when CVN testing cannot be completed; the referenced standard allows isolated precipitates below 10µm, which does not meet the stricter client requirement of no interm...

Open

10435

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

10436

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

10437

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

10438

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

10439

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content...

Open

10440

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 24h, 50°C) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m²; DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02 - S...

Open

10441

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destru...

Open

10442

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is confirmed for the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12...

Open

10443

5.2

AI

No

add date

Dye penetrant testing is offered for tube ends and bevels as per specification, matching the client inquiry which does not request full-length testing. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-05 - Dye pene...

Open

10444

5.2

AI

No

add date

No explicit confirmation that NDE acceptance criterion requiring rejection or repair of indications greater than the calibration notch is met; referenced standards and feasibility documents do not specify this rule or confirm its application for the ...

Open

10445

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A ...

Open

10446

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10447

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

10448

9.0

AI

No

add date

Weld repairs are explicitly stated as not acceptable in the specification under 'Surface finish / Repairs of defects' (§13, §14). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

10449

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

10450

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the required quality-assurance system per specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest ...

Open

10451

10.1

AI

No

add date

Supplier is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the qualification requirement for the specified ...

Open

10452

10.2

AI

No

add date

Certification includes EN 10204 type 3.1 with traceability to product, and MST-Tubes is ISO 9001 certified, fulfilling documentation and traceability requirements per SIR205 and specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

10453

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided, including all information required by ASTM A790 and NORSOK M-630 (heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary or QTR number). S...

Open

10454

10.2

AI

No

add date

Most required documentation and certification details (NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, metallurgical and NDT results) are stated as included in th...

Open

10455

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Source: Item Table, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10456

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

10457

3.1

AI

No

add date

AOD or equivalent refining is required and used for 100% of production, and chemical analysis complies with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10458

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat, confirming conformity to the required ...

Open

10459

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

10460

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement for DMV 25.7N. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSO...

Open

10461

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-0...

Open

10462

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled. For the ordered pipe (OD 219.1 ...

Open

10463

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1 at room temperature, and material meets the tensile and maximum hardness properties of Table 4 as required for DMV 25.7N seamless pipe per ASTM A790/NORSOK MDS D51. Source: DMV_STANDARD_BOOK/02...

Open

10464

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: minimum tensile strength 750 MPa, yield strength 550 MPa, elongation 25%, and maximum hardness 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

10465

4.3

AI

No

add date

Charpy V-notch testing is feasible and requirements are met for the specified pipe dimensions and wall thickness according to ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

10466

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, including minimum absorbed energy values and sub-size specimen reduction factors. The specified pipe dimensions allow for required Charpy V-notch impact testing in ...

Open

10467

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

10468

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

10469

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

10470

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

10471

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

10472

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/...

Open

10473

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully fulfilled. Source: DM...

Open

10474

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

10475

4.4.3

AI

No

add date

Microstructure must be basically free from intermetallic precipitates, isolated precipitates allowed if not distributed and <10µm, carbides/nitrides must be reported, and acceptance is based on impact and corrosion test results. DMV 25.7N complies an...

Open

10476

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

10477

4.5

AI

No

add date

No explicit confirmation or evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

10478

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Microstructure criteria (free from intermetallic precipitates, isolated precipitates <10µm...

Open

10479

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 24h, 50°C) is performed for DMV 25.7N, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m²; DMV 25.7N complies with these requirements. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

10480

5.1

AI

No

add date

No evidence is provided confirming NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non...

Open

10481

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available after all processing steps, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV...

Open

10482

5.2

AI

No

add date

NDE per ASTM A790 is referenced, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic te...

Open

10483

5.2

AI

No

add date

None of the relevant documents explicitly confirm that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor do they confirm standard NDE for the specified dimension at Montbard. Source: DMV_STAND...

Open

10484

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790 referencing ASTM A999) unless otherwise stated, with no deviations specified by TechnipFMC in the inquiry context. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_S...

Open

10485

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSO...

Open

10486

8.0

AI

No

add date

Marking per ASTM A790 and NORSOK MDS D51 includes heat number, DMV lot number, and other traceable information, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STA...

Open

10487

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

10488

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

10489

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

10490

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, fulfilling the requirement. Source: DMV_STANDARD_B...

Open

10491

10.2

AI

No

add date

Certification includes EN 10204 type 3.1 with traceability to heat treatment, steel manufacturer, melting/refining practice, and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, ensuring documentation is traceable to delivered products and ...

Open

10492

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary or QTR n...

Open

10493

10.2

AI

No

add date

Most documentation and certification requirements are stated as included in the EN 10204 3.1 certificate, except the steel producer name, which is not provided (only country of origin is given). No evidence is provided for actual test results, soluti...

Open

10494

1.0

AI

No

add date

DMV 25.7N (UNS S32760) is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified up to the required wall thickness. Source: DMV_STA...

Open

10495

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; full qualification to NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR is not confirmed. Source: DMV_STANDARD_BOOK/02...

Open

10496

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

10497

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis complies with Table 2 of ASTM A790 and NORSOK MDS D51 Rev 6. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10498

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10499

3.2

AI

No

add date

Solution annealing followed by accelerated cooling per ASTM A790 is confirmed, with manufacturing qualified to NORSOK M-650/ISO 17782. Free circulation of heating/cooling media is ensured by compliance with these standards and qualified procedures. S...

Open

10500

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10501

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

10502

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, directly referencing the required table for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

10503

4.1

AI

No

add date

Test sampling for seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, all in accordance with NORSOK MDS D51/AS...

Open

10504

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

10505

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

10506

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 and ISO 148-1 is feasible for the specified pipe dimensions; requirement is fulfilled. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

10507

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse absorbed energy (average/single) 45 J/35 J, minimum longitudinal absorbed energy (average/single) 65 J/50 J (if transverse...

Open

10508

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed according to ISO 17781, with specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

10509

4.4.1

AI

No

add date

Etching with 20-40% NaOH or KOH solution to reveal ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is required for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

10510

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Re...

Open

10511

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

10512

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report at actual magnification and with a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/...

Open

10513

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

10514

4.4.2

AI

No

add date

Microstructure requirements allow isolated intermetallic precipitates below 10μm, but do not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed, as required by the client specification. Source: DMV_STANDARD_BOO...

Open

10515

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

10516

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

10517

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS ...

Open

10518

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

10519

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements for ASTM A790 seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

10520

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 24h, 50°C) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m²; DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02 - S...

Open

10521

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

10522

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

10523

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790/NORSOK M-630 MDS D51 are not fully addressed; only general hydrostatic or NDE testing per ASTM A999 is confirmed, and plant feasibility for required NDE methods (eddy current, ultrasonic, full-length dye penetran...

Open

10524

5.2

AI

No

add date

No provided documentation confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor is there confirmation that the required NDE will be performed as standard for the spe...

Open

10525

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding TechnipFMC specification referenced. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A 376-...

Open

10526

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10527

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot, and the marking methods used (indelible ink and vibro-etching) include heat and lot numbers, ensuring compliance. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS ...

Open

10528

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' confirming the requirement is met. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev...

Open

10529

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

10530

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

10531

10.1

AI

No

add date

Supplier is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the qualification requirement for the specifi...

Open

10532

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products as required by SIR205 and section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

10533

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

10534

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive te...

Open

10535

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, including chemical, mechanical, manufacturing, and testing requirements. Source: DMV_STANDARD_BOOK/02-03-01...

Open

10536

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of QTR/MPCR documentation availability for review by TechnipFMC. Partial accreditation to M-650 only is noted, but not to ISO 17...

Open

10537

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV25.7N (UNS S32760) up to WT = 31.75 mm, with manufacturing process qualified per NORSOK M-650 or ISO 17782 and meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

10538

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent and chemical analysis complies with Table 2 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51...

Open

10539

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the required WT of 18.26 mm for the inquiry. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-...

Open

10540

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed per ASTM A790, with manufacturing process and furnaces qualified according to NORSOK M-650 or ISO 17782, ensuring compliance with requirements including free circulation...

Open

10541

4.1

AI

No

add date

No provided document confirms that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790. Partial information on individual tests exists, but...

Open

10542

4.1

AI

No

add date

None of the provided documents include or outline the test specimen sampling details as specified in Table 3; only references to Table 3 are made without reproducing its content or sampling method details. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ...

Open

10543

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no information on CVN impact testing, test directions for CVN, or detailed sampling locations as required by the specification. Requirements for CVN, corrosion, and microstructure testing are n...

Open

10544

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for DMV 25.7N as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

10545

4.2

AI

No

add date

No provided document confirms that DMV 25.7N meets the specified mechanical requirements for tensile strength, yield strength, elongation, or hardness. Mechanical data for other grades or general references to testing are insufficient for validation....

Open

10546

4.3

AI

No

add date

No evidence that Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 will be performed or that results will meet Table 5 requirements; relevant documents do not confirm compliance or testing execution. Source: DMV_STANDARD_BOOK/02-02-01 Di...

Open

10547

4.3

AI

No

add date

Impact testing at -46°C with required absorbed energy values for both longitudinal and transverse directions is feasible for the specified pipe size and wall thickness (>6mm), fulfilling the requirement. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Te...

Open

10548

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination according to ISO 17781 or specification of the required etchant solution for 25 Cr Duplex stainless steels is provided. No relevant information for duplex grades or required etching procedures...

Open

10549

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination or for revealing ferrite balance and intermetallic phases in the provided documentation.

Open

10550

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic phases; isolated phases are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

10551

4.4.2

AI

No

add date

No information or procedures are provided regarding the detection, recording, or micrographic documentation (400x minimum) of intermetallic phases or their locations. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I.doc

Open

10552

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at 400x minimum magnification with a scale bar and actual magnification when intermetallic phases are not detected as required by the specification. S...

Open

10553

4.4.2

AI

No

add date

No relevant documents address the detection, reporting, or acceptance criteria for centerline intermetallic stringers, nor their linkage to CVN and corrosion test results in case of their presence. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Exam...

Open

10554

4.4.2

AI

No

add date

Relevant documents allow isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not meet the stricter client requirement of zero tolerance for intermetallic phases and/or precipitates if CVN testing cann...

Open

10555

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided; only grain size examination is discussed, not the required ferrite determination methods or standards. Source: DMV_STANDARD_BOOK/12 - S...

Open

10556

4.4.3

AI

No

add date

No acceptance criteria for micrographic examination or related metallurgical properties are specified or addressed in the provided documents for DMV 25.7N or the order in question. Sources: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STA...

Open

10557

4.5

AI

No

add date

No explicit acceptance criteria for metallurgical properties are specified in the provided documents or section 4.0, so the requirement is not fulfilled. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest...

Open

10558

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

10559

5.1

AI

No

add date

No evidence provided regarding qualification or certification of NDE personnel to ISO 9712 level II or III, or their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDARD_BOOK/...

Open

10560

5.2

AI

No

add date

No confirmation of 100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10, nor details on reference notches as specified. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultrasonic tes...

Open

10561

5.2

AI

No

add date

100% qualitative anti-mixing PMI check is performed on standard production at Montbard using appropriate instruments, fulfilling general NDE acceptance criteria for PMI. Source: DMV_STANDARD_BOOK/12-06-06 - Positive Material Identification (PMI) in M...

Open

10562

5.2

AI

No

add date

ASTM A790 requires non-destructive testing per ASTM A999, which specifies that any indication greater than the calibration standard is cause for rejection or repair, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

10563

6.0

AI

No

add date

Dimensional tolerances for hot and cold finished products, including OD, WT, and ovality, are specified as per the applicable ASTM standards (A 790 with A 999 for tolerances) for the relevant size range, with no deviations or overrides indicated by T...

Open

10564

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and white pickled or bright annealed as per NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790 di...

Open

10565

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

10566

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

10567

10.0

AI

No

add date

No evidence of the manufacturer's quality-assurance system, ISO 9001 certification, or assessment by a competent EEA body is provided in the relevant documents. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Cert...

Open

10568

10.1

AI

No

add date

No evidence provided that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-03...

Open

10569

10.1

AI

No

add date

Certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N up to the required wall thickness for the specified size and product form. Source: DMV_STANDARD_BOOK...

Open

10570

10.2

AI

No

add date

No evidence that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205; documents only describe types of inspection and certification without confirming compliance with the transmission and traceability requi...

Open

10571

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 is issued and validated for mill inspection, with reference to ASTM A790 and NORSOK M-630 standards implying compliance with required information. Source: 14-03 - Certification Montbard plant.doc

Open

10572

4.3

AI

No

add date

DMV 25.7N fulfills NORSOK MDS D51 Rev 6 impact property requirements at -46°C: transverse (average 45 J, single 35 J), longitudinal (average 65 J, single 50 J) if transverse not possible; wall thickness > 6 mm allows required testing for the specifie...

Open

10573

10.2

AI

No

add date

No provided document contains the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or test results. Some docum...

Open

10574

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified and all relevant requirements are met. Source: DMV_STANDARD_BOOK/02...

Open

10575

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORS...

Open

10576

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, with manufacturing process qualified per NORSOK M-650 or ISO 17782 and meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

10577

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis is compliant with Table 2 for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10578

3.1

AI

No

add date

Chemical composition for S32760 matches Table 2 requirements and is confirmed to conform per heat analysis. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

10579

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

10580

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

10581

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling as outlined in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

10582

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes meets requirements: tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, per ASTM A790 and NORSOK. ...

Open

10583

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with results meeting the tensile and maximum hardness properties of Table 4. Hardness testing is also performed and results are provided. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

10584

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW, fulfilling the specified mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

10585

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions (WT 18.26 mm > minimum required), fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-0...

Open

10586

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10587

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with specified etchants after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

10588

4.4.1

AI

No

add date

Etching with 20–40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is explicitly required for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

10589

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

10590

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

10591

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness when intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

10592

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

10593

4.4.2

AI

No

add date

The available documents do not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed; isolated precipitates below 10µm are allowed, which does not meet the stricter client requirement that none are permitted in th...

Open

10594

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

10595

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

10596

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

10597

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

10598

4.5

AI

No

add date

DMV 25.7N complies with all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including destructive, micrographic, ferrite, and corrosion tests, as well as heat treatment, manufacturing, and M-650 qualification for the specified grade and ...

Open

10599

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 24h, 50°C) is performed for DMV 25.7N, with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/0...

Open

10600

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

10601

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is confirmed for the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12...

Open

10602

5.2

AI

No

add date

NDE per ASTM A790 is detailed, but compliance with additional NDE requirements of NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782 is not confirmed. For the specified OD, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only a...

Open

10603

5.2

AI

No

add date

None of the relevant documents explicitly confirm that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor do they specify this acceptance criterion for NDE. NDE feasibility for the requested di...

Open

10604

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) as required, with no overriding specification from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances ...

Open

10605

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10606

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

10607

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10608

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

10609

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

10610

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demonstration for th...

Open

10611

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

10612

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

10613

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice and refining method, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the actual steel produce...

Open

10614

1.0

AI

No

add date

DMV 25.7N is a 25 Cr Duplex stainless steel seamless pipe manufactured in compliance with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, with M-650 qualification and all relevant requirements met. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

10615

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm), but not to ISO 17782 as required. No evidence provided for availability of QTR/MPCR for review by TechnipFMC. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK ...

Open

10616

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10617

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

10618

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition complies with the specified requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10619

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including all specified element limits and PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 R...

Open

10620

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

10621

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

10622

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

10623

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure tests at specified ...

Open

10624

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370, with mechanical properties and maximum hardness meeting Table 4 requirements for NORSOK MDS D51/ASTM A790. Hardness testing is also performed as required. Source: DMV_STANDARD_BOOK/02-04...

Open

10625

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW, fulfilling the specified mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

10626

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness required for testing. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-...

Open

10627

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C (transverse: 45 J avg/35 J single; longitudinal: 65 J avg/50 J single if transverse not possible) for thickness ≥6 mm. The specified pipe dimensions allow for required...

Open

10628

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with specified etchants for intermetallic phases and ferrite balance after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

10629

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, is required for micrographic examination as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

10630

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

10631

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases. Source: DMV_STANDARD_BOOK/02...

Open

10632

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

10633

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

10634

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

10635

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

10636

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corro...

Open

10637

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10638

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or referenced; compliance cannot be confirmed based on the provided information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in M...

Open

10639

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

10640

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

10641

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

10642

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, performed after all mechanical processing, fulfilling the requirement for 100% longitudinal defect testing. Source: DMV_STANDARD_BOOK/12 ...

Open

10643

5.2

AI

No

add date

NDE per ASTM A790/A999 is detailed, but there is no explicit confirmation of compliance with NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 requirements. For the specified OD, eddy current testing is not feasible, and hydrostatic/ultrasonic tests ar...

Open

10644

5.2

AI

No

add date

None of the relevant documents explicitly state that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, nor do they confirm that NDE with this acceptance criterion is performed as sta...

Open

10645

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 seamless pipe are per the applicable ASTM standards (A790 and referenced A999), with no deviations specified by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOO...

Open

10646

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

10647

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10648

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

10649

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

10650

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

10651

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

10652

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with issuance and validation by Quality Control as standard practice for the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest N...

Open

10653

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution annealing parameters, an...

Open

10654

1.0

AI

No

add date

DMV 25.7N is a 25 Cr Duplex stainless steel grade, fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spe...

Open

10655

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; full qualification to NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR is not confirmed. Source: DMV_STANDARD_BOOK/02-...

Open

10656

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, with qualification testing per NORSOK M-630 MDS D51 rev. 6. Source: DMV_STANDARD_...

Open

10657

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10658

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10659

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

10660

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

10661

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

10662

4.1

AI

No

add date

All required tests (tensile, hardness, CVN, corrosion, microstructure) are performed on prolongation samples for seamless pipes as specified, with tensile and CVN tests in the transverse direction unless not feasible, and test locations and methods m...

Open

10663

4.2

AI

No

add date

Tensile testing is performed at room temperature in accordance with ASTM A370 or ISO 6892-1, and the material meets the specified tensile and maximum hardness properties. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

10664

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

10665

4.3

AI

No

add date

Charpy V-notch testing is feasible and the requirement is fulfilled as the pipe wall thickness exceeds the minimum required for testing according to ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/1...

Open

10666

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements, including Charpy V-notch testing at -46°C with minimum absorbed energy values (transverse: 45 J average/35 J single; longitudinal: 65 J average/50 J single) and reduction factors for ...

Open

10667

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

10668

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

10669

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

10670

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

10671

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

10672

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

10673

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully fulfilled. So...

Open

10674

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

10675

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impa...

Open

10676

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

10677

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided; applicable norms listed do not include these standards. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant....

Open

10678

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORS...

Open

10679

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, meeting the criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

10680

5.1

AI

No

add date

No evidence is provided confirming NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor are their roles and responsibilities as defined in ISO 9712 addressed. Source: DMV_STANDARD_BOOK/12-02-01 -...

Open

10681

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 and ISO 10893-10 is available for the required pipe dimensions, including reference notches per ASTM E213 specification. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic tes...

Open

10682

5.2

AI

No

add date

NDE per ASTM A790 is generally feasible, but specific NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 requirements are not confirmed as fulfilled. Eddy current testing for OD 219.1 mm is not standardly feasible at Montbard, and multi-element pr...

Open

10683

5.2

AI

No

add date

None of the relevant documents confirm that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor do they demonstrate that the specified NDE acceptance criterion will be applied f...

Open

10684

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and ASTM A999 as specified, with no overriding customer requirements indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 790-02.doc...

Open

10685

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10686

8.0

AI

No

add date

Marking includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and NORSOK MDS D51 Rev 6. Source: Digest NORSOK MDS D51 Rev 06.docx, Standard marking feasibility - Montbard...

Open

10687

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 (§13, §14) for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10688

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

10689

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

10690

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the requirement for qualification for the sp...

Open

10691

10.2

AI

No

add date

ISO 9001 certification is provided and documentation traceable to delivered products is included as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Diges...

Open

10692

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

10693

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive test...

Open

10694

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all referenced mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STA...

Open

10695

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782, and there is no confirmation of QTR/MPCR availability for review as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev...

Open

10696

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, with qualification testing meeting NORSOK M-630 MDS D51 rev. 6 requirements. Sour...

Open

10697

3.1

AI

No

add date

AOD or equivalent refining is required and used for 100% of production, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10698

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NO...

Open

10699

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

10700

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, matching the requirement for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

10701

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for sampling requirements, fulfilling the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03...

Open

10702

4.5

AI

No

add date

Corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is not explicitly confirmed or documented in the available information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

10703

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N, ASTM A790, NORSOK) is fulfilled: tensile tests are performed longitudinally or transversely, CVN impact tests are feasible in transverse direction for the specified dimensions, and hardness, corrosion, and...

Open

10704

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

10705

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

10706

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and standards; requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/1...

Open

10707

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse (45 J average, 35 J single) and longitudinal (65 J average, 50 J single if transverse not possible) absorbed energies, and ...

Open

10708

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, using the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

10709

4.4.1

AI

No

add date

Etching with 20–40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BOOK/0...

Open

10710

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

10711

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

10712

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

10713

4.4.2

AI

No

add date

Micrographic examination requires reporting of centerline intermetallic stringers, with acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

10714

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is...

Open

10715

4.4.3

AI

No

add date

Ferrite content is determined per ASTM E562 or by image analysis according to ASTM E1245, performed in accordance with ISO 17781, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-...

Open

10716

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, including etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and co...

Open

10717

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

10718

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 06 are fully met, including tensile, impact, corrosion, ferrite, microstructure, solution annealing, ferrite range, absence of intermetallics, and all referenced test methods and...

Open

10719

4.5

AI

No

add date

DMV 25.7N meets the pitting corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours, with no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

10720

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III, nor are their roles and responsibilities defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard pl...

Open

10721

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is confirmed for the required dimensions. Acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic t...

Open

10722

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT) is confirmed, but compliance with specific NDE requirements of NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782 is not demonstrated. For OD 219.1 mm, Eddy current testing is not feasible, and hydrostatic/...

Open

10723

5.2

AI

No

add date

None of the referenced documents explicitly confirm that any indication greater than that produced by the calibration notch is treated as a defect and that defective pipe and tubing are rejected or repaired according to this criterion. NDE acceptance...

Open

10724

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standards (ASTM A999), with no overriding specifications from TechnipFMC indicated. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDAR...

Open

10725

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10726

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

10727

9.0

AI

No

add date

Weld repairs are explicitly not acceptable as stated in NORSOK MDS D51 Rev 06, §14 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK...

Open

10728

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, meeting the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

10729

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

10730

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

10731

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products being delivered as required by SIR205 and section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

10732

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and covering heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification su...

Open

10733

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive te...

Open

10734

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, as referenced in the engineering data and confirmed by specification digests. Source: DMV_STANDARD_BOOK/02-...

Open

10735

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782; no evidence of QTR/MPCR availability or full compliance with both standards as required for qualification of the exact product supplied. Source: DMV_STANDARD_BOOK/02-04-03 - D...

Open

10736

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

10737

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10738

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed to be fulfilled for DMV material with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dige...

Open

10739

3.2

AI

No

add date

Solution annealing followed by accelerated cooling per ASTM A790 is confirmed, with manufacturing and furnace qualification per NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured ...

Open

10740

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot, with 'lot' defined according to ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

10741

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for sampling requirements, fulfilling the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03...

Open

10742

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, longitudinal if not possible), and corrosion/microstructure tests are performed at specified ...

Open

10743

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, with mechanical properties meeting Table 4 requirements (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%). Hardness testing is performed per ASTM A790, referencing ASTM A370. DMV 25.7N...

Open

10744

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets the minimum requirements for tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as specified in NORSOK MDS D51 Rev 6 and ASTM A790 for duplex stainless steel seamles...

Open

10745

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370 and ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03...

Open

10746

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is confirmed for the required dimensions. Acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic t...

Open

10747

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C with minimum transverse values of 45 J (average) and 35 J (single), and longitudinal values of 65 J (average) and 50 J (single) if transverse ...

Open

10748

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with 20-40% NaOH or KOH solution after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

10749

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

10750

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

10751

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

10752

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

10753

4.4.2

AI

No

add date

Micrographic examination requires reporting of centerline intermetallic stringers, with acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

10754

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully met. Source: ...

Open

10755

4.4.3

AI

No

add date

Ferrite content is determined per ASTM E562 or by image analysis according to ASTM E1245, performed in accordance with ISO 17781, with a specified ferrite range of 35-60%. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

10756

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, including etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and co...

Open

10757

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

10758

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) performed in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

10759

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORS...

Open

10760

4.5

AI

No

add date

Requirement for no pitting at 20X magnification and weight loss less than 1.0 g/m² is met per ISO 17781 G48 Method A at 50°C for 24 hours; DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

10761

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

10762

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially addressed, but specific NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 requirements are not evidenced. For the requested OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/u...

Open

10763

5.2

AI

No

add date

None of the referenced documents confirm that indications greater than the calibration notch are classified as defects and require rejection or repair as specified; acceptance criteria and explicit rejection/repair policy are not addressed or validat...

Open

10764

6.0

AI

No

add date

Dimensional tolerances are per ASTM A999 as referenced by ASTM A790 for seamless pipe, with no overriding specification from TechnipFMC. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 -...

Open

10765

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10766

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

10767

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

10768

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, meeting the requirement for an appropriate quality-assurance system certified by a competent body established within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

10769

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

10770

10.1

AI

No

add date

MST-Tubes provides NORSOK M-650 Manufacturing Summary identification or QTR number in the EN 10204 3.1 certificate for DMV 25.7N (UNS S32760) up to the required wall thickness, demonstrating qualification for the size and product form per NORSOK M-65...

Open

10771

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

10772

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference). Source: DMV_STANDARD_BOOK/02-04-0...

Open

10773

10.2

AI

No

add date

EN 10204 type 3.1 certificate for DMV 25.7N will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MPCR number, steel producer, steel melting/refining method, heat number, ladle chemical analysis, solution annealing details, ...

Open

10774

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/...

Open

10775

1.0

AI

No

add date

Supplier is only accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) and not to ISO 17782; no confirmation of QTR/MPCR availability for review. Requirement for qualification to both NORSOK M-650/ISO 17782 and documentation avai...

Open

10776

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

10777

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10778

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PREN ≥ 40, and meets ASTM A790 and NORSOK MDS D51 Rev 06 standards for all specified elements and limits. Source: 02-03-01 - Digest ASTM A 790.docx, 02-0...

Open

10779

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and furnace qualification ensures free circulation of heating/cooling media. Source: DMV_STANDARD_BOO...

Open

10780

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

10781

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and lot definition, directly matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

10782

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure tests at specified thickness locations. For t...

Open

10783

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with tensile and hardness properties meeting Table 4 requirements for NORSOK MDS D51/ASTM A790. Source: Digest NORSOK MDS D51 Rev 06.docx

Open

10784

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW, matching Table 4 specifications. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

10785

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the requested pipe dimensions, which exceed the minimum wall thickness required for transverse specimens in both ASTM and ISO standards. Source: DMV_STANDARD_BOOK/12 - Spe...

Open

10786

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse absorbed energy (average/single) of 45 J/35 J, minimum longitudinal absorbed energy (average/single) of 65 J/50 J if trans...

Open

10787

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants after final polishing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

10788

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORS...

Open

10789

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

10790

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

10791

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos including actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

10792

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

10793

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fulfilled. Source: Digest NORS...

Open

10794

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

10795

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosio...

Open

10796

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

10797

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

10798

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements, with M-650 qualification up to the specified wall thickness. Source: DMV_STANDARD_BOOK/02...

Open

10799

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

10800

5.1

AI

No

add date

No evidence is provided confirming NDE personnel are qualified and certified to ISO 9712 level II or III, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

10801

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed after all mechanical processing, heat treatments, and straightening, with acceptance of ASTM E213 implying compliance with calibration notch requirements. Sou...

Open

10802

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE acceptance criteria are addressed. For the requested OD (219.1 mm), standard NDE methods (EC, UT, hydrostatic) are not ful...

Open

10803

5.2

AI

No

add date

No provided documentation explicitly confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that such NDE acceptance criteria are standardly performed or feasible for the specified pipe ...

Open

10804

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no deviations or special tolerances specified in the customer request. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03...

Open

10805

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10806

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-0...

Open

10807

9.0

AI

No

add date

Weld repairs are explicitly stated as not acceptable in the specification under 'Surface finish / Repairs of defects' (§13, §14). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

10808

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, meeting the requirement for an appropriate quality-assurance system certified by a competent body established within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

10809

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

10810

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified ...

Open

10811

10.2

AI

No

add date

ISO 9001 certification is provided and documentation traceable to delivered products is included, fulfilling SIR205 and specification section 10.0 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/...

Open

10812

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

10813

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and complete metallurgical and non-destructive test res...

Open

10814

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified requirements and is confirmed to conform to Table 2 of ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest A...

Open

10815

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

10816

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, using the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

10817

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

10818

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, including etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and co...

Open

10819

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in...

Open

10820

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no evidence of override in the customer specification or TechnipFMC documentation. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDAR...

Open

10821

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed by supplier certification and heat analysis per ASTM A790 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dige...

Open

10822

3.2

AI

No

add date

Solution annealing followed by accelerated cooling is performed per ASTM A790; manufacturing and furnaces are qualified to NORSOK M-650/ISO 17782; free circulation of heating/cooling media is ensured by compliance with these standards. Source: DMV_ST...

Open

10823

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot, with 'lot' defined according to ASTM A790, fulfilling the requirement for each heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04...

Open

10824

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and direct reference to Table 3, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ...

Open

10825

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified t...

Open

10826

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

10827

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 06 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

10828

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness (>6mm), fulfilling the requirement. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

10829

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse 45/35 J and longitudinal 65/50 J (average/single), with sub-size reduction factors applied. The specified pipe dimensions a...

Open

10830

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, using 20-40% NaOH or KOH solution for etching after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

10831

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution for micrographic examination to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

10832

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

10833

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

10834

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

10835

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

10836

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

10837

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size. No other relevant sources address the requirem...

Open

10838

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Sou...

Open

10839

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, including etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and co...

Open

10840

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

10841

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements, with manufacturing and qualification processes compliant with NORSOK M-650/ISO 17782. Sou...

Open

10842

4.5

AI

No

add date

DMV 25.7N undergoes pitting corrosion testing per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

10843

5.1

AI

No

add date

No information is provided confirming NDE personnel qualification or certification to ISO 9712 level II or III, nor definition of their roles and responsibilities as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibili...

Open

10844

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

10845

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not validated; only ASTM A790/A999 NDE is confirmed. For the requested OD (219.1 mm), standard eddy current and ultrasonic/hydrostatic testing are not fully feasible or o...

Open

10846

5.2

AI

No

add date

The available documents do not explicitly confirm that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor do they guarantee the required NDE capability for the specified pipe dimensions and sta...

Open

10847

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standards (ASTM A999), with no deviations specified in the customer documentation. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerance...

Open

10848

8.0

AI

No

add date

Marking is performed according to ASTM A790, including heat number and lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standar...

Open

10849

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

10850

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

10851

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size ...

Open

10852

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

10853

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and relevant manufacturing summary or QTR number....

Open

10854

10.2

AI

No

add date

EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. Chemical analysis, ...

Open

10855

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all referenced mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified up to the required wal...

Open

10856

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51...

Open

10857

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

10858

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, and matches ASTM A790 and NORSOK MDS D51 Rev 06 specifications. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/...

Open

10859

3.2

AI

No

add date

Solution annealing followed by accelerated cooling is performed per ASTM A790; manufacturing and furnace qualification are per NORSOK M-650/ISO 17782; MST-Tubes is M-650 accredited for DMV 25.7N; free circulation of heating/cooling media is ensured b...

Open

10860

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

10861

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement for test specimens sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-...

Open

10862

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes per ASTM A790/NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure tests are performed at specified lo...

Open

10863

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, meeting the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Hardness testing is also performed per ASTM A790, with results provided. Source...

Open

10864

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required in Table 4 for ASTM A790/NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

10865

4.3

AI

No

add date

Pipe dimensions exceed minimum wall thickness for Charpy V-notch testing per ASTM A370 and ISO 148-1; testing is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests...

Open

10866

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C (transverse: 45J/35J, longitudinal: 65J/50J) and sub-size reduction factors. The specified pipe dimensions allow both longitudinal and transverse impact testing as r...

Open

10867

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching for intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and examination in accordance ...

Open

10868

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

10869

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

10870

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

10871

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report at actual magnification and with a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness if int...

Open

10872

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

10873

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NO...

Open

10874

4.4.3

AI

No

add date

Ferrite content is determined per ASTM E562 or by image analysis according to ASTM E1245, performed in accordance with ISO 17781, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

10875

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 at ≥400X magnification, with etching to detect intermetallic phases, nitrides, and carbides. Structure must be basically free from intermetallic precipitates; isolated precipitates allowed if not ...

Open

10876

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

10877

4.5

AI

No

add date

DMV 25.7N (UNS S32760) fulfills all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and N...

Open

10878

4.5

AI

No

add date

DMV 25.7N undergoes pitting corrosion testing per ISO 17781 G48 Method A at 50°C for 24h, with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², both of which are met for this grade. Source: DMV_STANDARD_BOOK/...

Open

10879

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

10880

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is fulfilled for the specified pipe dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Test...

Open

10881

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially addressed with 100% hydrostatic or NDE (EC or UT) testing, but there is no explicit evidence of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements. For th...

Open

10882

5.2

AI

No

add date

The requirement that any indication greater than that produced by the calibration notch represents a defect, with defective pipe and tubing to be rejected or repaired, is not explicitly confirmed or supported in the referenced specifications or feasi...

Open

10883

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specifications stated by TechnipFMC. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 790-02 (A 999-01...

Open

10884

8.0

AI

No

add date

Marking is performed according to ASTM A790 (§14) and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV...

Open

10885

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

10886

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

10887

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV25.7N, and the EN 10204 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number for the specified size and product form. Source: DMV_ST...

Open

10888

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and specification section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

10889

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant standards and qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D...

Open

10890

10.2

AI

No

add date

Required documentation and traceability details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and actual metallurgical and non-destructive test results are...

Open

10891

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with all relevant chemical, mechanical, and testing requirements fulfilled, including manufacturing process...

Open

10892

1.0

AI

No

add date

No document confirms supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor the availability of the full QTR/MPCR and supporting documentation for review by TechnipFMC upon request. Source: DMV_STANDARD_BOOK/02-...

Open

10893

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N within specified wall thickness limits, and the manufacturing process is qualified per NORSOK M-650 (or ISO 17782), meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_...

Open

10894

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis complies with Table 2 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

10895

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the inquiry WT = 18.26 mm is within this range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04...

Open

10896

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed per ASTM A790, with manufacturing process and furnaces qualified according to NORSOK M-650 or ISO 17782. Free circulation of heating/cooling media is ensured by complian...

Open

10897

4.1

AI

No

add date

No provided document confirms that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A ...

Open

10898

4.1

AI

No

add date

None of the relevant sources reproduce or outline the test specimen sampling details from Table 3; only references to Table 3 are made without providing the actual sampling information. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV...

Open

10899

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no evidence of CVN impact testing, required test directions for CVN, or details on hardness, corrosion, and microstructure sampling as specified in Table 3. Test sampling requirements are not f...

Open

10900

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature with criteria meeting or exceeding Table 4 (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%), and referenced standards require testing in accordance with ASTM A370 or ISO 6892-1. Source: DMV_STANDARD_BO...

Open

10901

4.2

AI

No

add date

Mechanical requirements for DMV 25.7N (tensile strength, yield strength, elongation, hardness) are not confirmed; relevant data is missing or not applicable to the specified grade. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STAN...

Open

10902

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the ordered pipe (NPS 8, 219.1mm OD, 18.26mm WT), as it exceeds the minimum wall thickness required for both standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-0...

Open

10903

4.3

AI

No

add date

Pipe dimensions allow for transverse Charpy V-notch specimens; impact property requirements at -46°C are feasible and can be fulfilled for this product. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

10904

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination according to ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/1...

Open

10905

4.4.1

AI

No

add date

No information confirming the use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination is provided. Requirement is not addressed for ferrite balance and intermetallic phase revelation in...

Open

10906

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic phases; isolated phases are permitted if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev ...

Open

10907

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Micrographic Examination/12-03-03 - Grain Siz...

Open

10908

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included at actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDARD_BOO...

Open

10909

4.4.2

AI

No

add date

No provided documentation addresses the reporting of centerline intermetallic stringers or links product acceptance to CVN and corrosion test results if such stringers are present. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I....

Open

10910

4.4.2

AI

No

add date

NORSOK MDS D41 Rev 06 and D51 Rev 06 allow isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not fully meet the requirement that intermetallic phases and/or precipitates are not permitted at all if ...

Open

10911

4.4.3

AI

No

add date

No information is provided confirming ferrite content determination per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Micrographic Examination...

Open

10912

4.4.3

AI

No

add date

No acceptance criteria or requirements for micrographic examination are provided or addressed for DMV 25.7N in the relevant documents. Grain size examination is noted as not applicable to duplex/super-duplex grades such as DMV 25.7N. Source: DMV_STAN...

Open

10913

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly fulfilled for DMV 25.7N according to the specifications and compliance statements in the referenced documents. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDAR...

Open

10914

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the 'Requested Positions' table and confirmed by the digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STAN...

Open

10915

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N with the specified wall thickness, and manufacturing is qualified per NORSOK M-650/ISO 17782 with testing per NORSOK M-630 MDS D51 rev. 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

10916

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Heat analysis is performed per heat and matches the specified limits for all elements listed in the...

Open

10917

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for one set per heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

10918

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, all per ASTM A790 and NORSOK re...

Open

10919

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

10920

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal. The specified pipe dimensions allo...

Open

10921

1.0

AI

No

add date

Supplier is M-650 accredited for DMV 25.7N but not accredited to ISO 17782 as required; no evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10922

4.5

AI

No

add date

No specific acceptance criteria are provided under the requirement, making validation impossible. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

10923

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria: no pitting at 20X magnification and weight loss < 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

10924

5.1

AI

No

add date

No provided documents contain information about NDE personnel qualification or certification to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV...

Open

10925

5.2

AI

No

add date

No confirmation of 100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10, nor reference notches as specified in Figure 3 of ASTM E213 is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing...

Open

10926

5.2

AI

No

add date

Dye penetrant testing is available for tube ends and bevels as per standard practice, and 100% qualitative anti-mixing PMI is performed on standard production at Montbard, meeting the acceptance criteria for NDE requirements. Source: DMV_STANDARD_BOO...

Open

10927

5.2

AI

No

add date

Eddy Current NDE is not feasible for the requested OD at Montbard, and none of the referenced documents explicitly state the acceptance criterion or rejection/repair policy for indications greater than the calibration notch as required. Source: DMV_S...

Open

10928

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for hot and cold finished products are per the applicable ASTM standards (A790/A999, A213/A1016, A268, A269, A789, A312, A376, A511), with no alternative tolerances specified, fulfilling the requirement ...

Open

10929

7.0

AI

No

add date

Both ASTM A790 and NORSOK MDS S01 Rev 05 require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS S01 Rev 05 .docx

Open

10930

9.0

AI

No

add date

Weld repairs are not acceptable as per NORSOK MDS S01 Rev 05 for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

10931

10.0

AI

No

add date

No evidence of ISO 9001 certification or assessment by a competent EEA body for the material manufacturer is provided in the relevant documents. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Certification Montba...

Open

10932

10.1

AI

No

add date

No evidence is provided that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification. Source: DMV_STANDARD_BOOK/14-03 - Certification Montbard plant.doc

Open

10933

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and the QTR number is included in the certificate, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

10934

10.2

AI

No

add date

No explicit evidence that documentation traceable to the products and transmitted to TechnipFMC as per SIR205 will be provided or is traceable to the delivered products as required. No statement of compliance with the specific documentation and trace...

Open

10935

10.2

AI

No

add date

Material certificate is issued according to EN 10204 Type 3.1 and validated by Quality Control for mill inspection, meeting the requirement for certification process compliance. Source: 14-03 - Certification Montbard plant.doc

Open

10936

5.1

AI

No

add date

No information is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, D...

Open

10937

10.2

AI

No

add date

None of the provided documents contain the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or metallurgical a...

Open

10938

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, including mechanical, chemical, and testing requirements. The product is M-650 qualified up to the required...

Open

10939

1.0

AI

No

add date

No document confirms supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor the availability of the full Qualification Test Record/MPCR for review by TechnipFMC as required by the specification. MST-Tubes is M-6...

Open

10940

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm for hot finished, 10.925 mm for cold finished), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 requirements. ...

Open

10941

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis complies with Table 2 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

10942

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the inquiry's wall thickness (18.26 mm) is within this range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Diges...

Open

10943

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing and heat treatment qualified to NORSOK M-650. Free circulation of heating and cooling media is ensured by compliance with these ...

Open

10944

4.1

AI

No

add date

No evidence is provided that impact, tensile, hardness, corrosion testing, and microstructure examinations are performed for each heat and heat treatment lot as defined in ASTM A790. Testing frequency and lot-based compliance are not confirmed for al...

Open

10945

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

10946

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no evidence of CVN impact, hardness, or corrosion/microstructure testing, nor of required test directions or thickness locations for any test. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A...

Open

10947

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature with criteria matching or exceeding Table 4 (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%), and DMV 25.7N complies. Reference to NORSOK MDS D51, which aligns with ASTM A790, supports fulfillment of t...

Open

10948

4.2

AI

No

add date

None of the provided documents confirm the required mechanical properties (tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, hardness max 310 HBW for UNS S32760/300 HBW for UNS S32750) for the specified duplex grades. Source: DM...

Open

10949

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible and fulfilled for the specified pipe dimensions, which exceed the minimum wall thickness required for testing. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12...

Open

10950

4.3

AI

No

add date

Impact testing at -46°C with specified absorbed energy values is feasible for the requested pipe dimensions (OD 219.1mm, WT 18.26mm), which meet the requirements for both longitudinal and transverse specimens. Source: DMV_STANDARD_BOOK/12-03-02 - Imp...

Open

10951

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination according to ISO 17781 or the specified etchant and electrolytic etching procedure for 25 Cr Duplex stainless steels. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03...

Open

10952

4.4.1

AI

No

add date

No information confirming the use of 20-40% NaOH or KOH solution (or other suitable etchant) for micrographic examination as per ISO 17781 Appendix B; only grain size measurement for austenitic materials is discussed, not ferrite balance or intermeta...

Open

10953

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic phases; isolated phases are permitted if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev ...

Open

10954

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Micrographic Examination/12-03-03 - Grain Siz...

Open

10955

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

10956

4.4.2

AI

No

add date

No relevant documentation addresses the reporting of centerline intermetallic stringers or acceptance based on CVN and corrosion test results in case they are present. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I.doc, DMV_STAN...

Open

10957

4.4.2

AI

No

add date

Referenced documents allow isolated intermetallic precipitates below 10µm and do not fully prohibit intermetallic phases/precipitates when CVN testing cannot be completed, as required by the client specification. The requirement for zero tolerance is...

Open

10958

4.4.3

AI

No

add date

No information is provided regarding ferrite content determination by ASTM E 562 or ASTM E 1245 in accordance with ISO 17781; only grain size measurement is discussed, and micrographic examination results for ferrite content are not addressed. Source...

Open

10959

4.4.3

AI

No

add date

No provided documentation addresses acceptance criteria or results for micrographic examination or metallurgical properties relevant to section 4.4. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORS...

Open

10960

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly fulfilled for DMV 25.7N according to the specifications in the referenced documents. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest N...

Open

10961

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

10962

4.5

AI

No

add date

No specific acceptance criteria are provided for metallurgical properties, and relevant standards or digests do not specify criteria for DMV 25.7N or A790 NORSOK in the context of the requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 79...

Open

10963

4.5

AI

No

add date

Specification requires pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², matching the client's requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

10964

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: ASTM A790, NORSOK MDS D51 Rev 6

Open

10965

5.2

AI

No

add date

No confirmation of 100% ultrasonic testing per ASTM E213 or ISO 10893-10 after all processing, nor details on reference notches or compliance with specified standards are provided. Dimensional limits for UT are mentioned, but not the required procedu...

Open

10966

5.2

AI

No

add date

100% qualitative anti-mixing PMI checks are performed on standard production using appropriate instruments, with quantitative PMI procedures and reporting attached to EN 10204 3.x certificates, fulfilling the NDE requirement for PMI. Source: DMV_STAN...

Open

10967

5.2

AI

No

add date

None of the relevant documents confirm that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor do they specify this acceptance criterion for NDE at Montbard for the requested dimensions. Source: D...

Open

10968

6.0

AI

No

add date

Dimensional tolerances for the requested product will be per the applicable ASTM standard (A790/A999) for the specified dimensions, with no deviations or special tolerances indicated in the customer specification. This fulfills the requirement that t...

Open

10969

7.0

AI

No

add date

Finished pipes are required to be white pickled or bright annealed, which is directly specified in both ASTM A790 and NORSOK MDS S01 standards for surface condition and finish. Source: ASTM A790 digest, NORSOK MDS S01 Rev 05.

Open

10970

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13 - Marking/13-02 - Standard marking feasibility/13-02-01 - Standard marking feasibility - Montbard plant/13...

Open

10971

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 specifies that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK...

Open

10972

10.0

AI

No

add date

No evidence is provided of an ISO 9001 certified quality-assurance system by a competent EEA body with specific assessment for materials at the Montbard plant. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Certi...

Open

10973

10.1

AI

No

add date

No evidence of ISO 9001 certification by a competent EEA body with specific assessment for materials is provided. Source: DMV_STANDARD_BOOK/14-03 - Certification Montbard plant.doc

Open

10974

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling supplier qualification documentation per SIR1...

Open

10975

10.2

AI

No

add date

No provided document confirms that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC. There is no explicit evidence of traceability or transmission process for the required documentation. Source: DMV_STA...

Open

10976

10.2

AI

No

add date

Material certificate is issued according to EN 10204 Type 3.1 and validated by Quality Control for mill inspection, meeting the requirement for certificate type and process compliance. Source: 14-03 - Certification Montbard plant.doc

Open

10977

10.2

AI

No

add date

None of the provided documents include the required documentation or certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing paramete...

Open

10978

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, corrosion, and qualification requirements. Manufacturing, testing, and certification are in accordance with th...

Open

10979

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N but not to ISO 17782, as required. No evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10980

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

10981

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10982

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits and PREN minimum specified in Table 2, as confirmed by both ASTM A790 and NORSOK MDS D51 Rev 6 digests. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

10983

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650/ISO 17782, and proper pipe placement during heat treatment is ensured. So...

Open

10984

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

10985

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

10986

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure tests are performed at specified locations an...

Open

10987

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

10988

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required by NORSOK MDS D51 Rev 6 and ASTM A790 for duplex stainless steel seamless pipe. Source: DMV_ST...

Open

10989

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe size and wall thickness (>6mm, 18.26mm WT). Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 ...

Open

10990

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if transverse...

Open

10991

4.4.1

AI

No

add date

Micrographic examination per ISO 17781 is referenced, but the specific etchant and electrolytic etching procedure required after final polishing are not confirmed or detailed as specified by the client. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NOR...

Open

10992

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution for micrographic examination to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

10993

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly prohibits weld repairs under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

10994

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

10995

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

10996

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

10997

4.4.2

AI

No

add date

Micrographic examination requires reporting of centerline intermetallic stringers, with acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

10998

4.4.2

AI

No

add date

The available specifications allow isolated intermetallic precipitates below 10μm and do not prohibit all intermetallic phases/precipitates if CVN testing cannot be completed, which is stricter in the client requirement. Source: DMV_STANDARD_BOOK/02-...

Open

10999

4.4.3

AI

No

add date

Ferrite content is checked per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite determination by these methods in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

11000

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corr...

Open

11001

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

11002

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

11003

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive, micrographic, corrosion tests, ferrite content, heat treatment, and manufacturing process; plant is M-650 accredited for required wall thickness ra...

Open

11004

4.5

AI

No

add date

DMV 25.7N undergoes pitting corrosion testing per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

11005

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

11006

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is confirmed for the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic t...

Open

11007

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790/NORSOK M-630 MDS D51/NORSOK M-650/ISO 17782 are not fully addressed; provided documents confirm general NDE capability (hydrostatic, EC, UT) but do not demonstrate fulfillment of specific NORSOK requirements or a...

Open

11008

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis complies with Table 2 for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11009

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair; NDE acceptance criteria and feasibility for the specified OD are not demonstrated for Montbard plant or in referenced s...

Open

11010

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with OD, WT, and ovality tolerances confirmed for the requested dimensions; no overriding TechnipFMC tolerances are specified. Source: DMV_STANDARD_BOOK/07.01...

Open

11011

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot, and Montbard standard marking methods (indelible ink, vibro-etching) include heat number and DMV lot number, ensuring compliance. Source: DMV_STANDARD_BOOK/02-04-03 - Di...

Open

11012

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

11013

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

11014

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demons...

Open

11015

10.2

AI

No

add date

ISO 9001 certification is provided and documentation traceable to delivered products is included as required by SIR205 and specification section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 -...

Open

11016

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

11017

10.2

AI

No

add date

No provided documentation confirms inclusion of all required items: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis (ladle), solution annealing parameters, or complete metallu...

Open

11018

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

11019

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; full qualification to both standards is required and not demonstrated. QTR/MPCR documentation availability is not confirmed. Source: DMV_STA...

Open

11020

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

11021

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

11022

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782; no evidence of QTR/MPCR availability as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11023

3.2

AI

No

add date

Solution annealing followed by accelerated cooling per ASTM A790 is confirmed, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is implicit in compliance wi...

Open

11024

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

11025

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

11026

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes per ASTM A790/NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specified loc...

Open

11027

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, with material meeting the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

11028

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

11029

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and meets ASTM A370 and ISO 148-1 requirements for minimum wall thickness. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-0...

Open

11030

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse average/single values of 45 J/35 J, and longitudinal average/single values of 65 J/50 J if transverse is not possible. The...

Open

11031

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed according to ISO 17781, with specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

11032

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

11033

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

11034

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 is performed with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

11035

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

11036

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

11037

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm if not distributed over the whole specimen, which does not meet the stricter requirement of zero tolerance for intermetallic phases and/or precipitates when CVN testin...

Open

11038

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

11039

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with required etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impac...

Open

11040

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS ...

Open

11041

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

11042

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content...

Open

11043

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

11044

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

11045

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 can be performed after all processing steps, and the pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructiv...

Open

11046

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially met via hydrostatic or NDE (EC or UT) per ASTM A999, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD ...

Open

11047

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor is there confirmation that the required NDE will be performed as standard for the requested dime...

Open

11048

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and referenced ASTM A999 for the specified product dimensions, with no overriding requirements from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 -...

Open

11049

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11050

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, ensuring full traceability to melt and heat treatment lot. Marking methods include heat number and DMV lot number for traceability. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx,...

Open

11051

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produc...

Open

11052

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

11053

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

11054

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, fulfilling the qualification requirement. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

11055

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

11056

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO177...

Open

11057

10.2

AI

No

add date

Required documentation and traceability details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive testi...

Open

11058

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Di...

Open

11059

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

11060

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent and chemical analysis conforms to Table 2; DMV 25.7N complies and certification includes steel melting and refining practice. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11061

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed by heat analysis with supplier certification for DMV material. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03...

Open

11062

3.2

AI

No

add date

Pipes are solution annealed followed by water quenching per ASTM A790, furnaces are qualified to NORSOK M-650/ISO 17782, and pipes are placed to ensure free circulation of heating and cooling media during heat treatment including accelerated cooling....

Open

11063

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

11064

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement for test specimens sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-...

Open

11065

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11066

4.1

AI

No

add date

Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure at specified locations, are fulfilled for DMV 25.7N. The ordered ...

Open

11067

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

11068

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

11069

4.3

AI

No

add date

Charpy V-notch testing is feasible and the requirement is fulfilled for the specified pipe dimensions according to ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - ...

Open

11070

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal, including reduction factors for sub...

Open

11071

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

11072

4.4.1

AI

No

add date

Etching with 20–40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

11073

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

11074

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

11075

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

11076

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

11077

4.4.2

AI

No

add date

The available specifications allow isolated intermetallic precipitates below 10 µm and do not confirm a zero-tolerance policy for intermetallics/precipitates if CVN testing cannot be completed, so the requirement is not fully fulfilled. Source: DMV_S...

Open

11078

4.4.3

AI

No

add date

Ferrite content is checked per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite determination by these methods in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

11079

4.4.3

AI

No

add date

Micrographic examination per ISO 17781 is specified, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impact ...

Open

11080

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

11081

4.5

AI

No

add date

No explicit evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or confirmed. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

11082

4.5

AI

No

add date

DMV 25.7N meets all metallurgical property requirements and acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782 qualification, including chemical composition, mechanical properties, impact, corrosion, microstructure, a...

Open

11083

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 24h, 50°C) is performed for DMV 25.7N, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m²; DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

11084

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

11085

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within the machine's capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive...

Open

11086

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not addressed; only ASTM A790/A999 requirements are partially confirmed. For OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are...

Open

11087

5.2

AI

No

add date

The available documents do not explicitly state that any indication greater than that produced by the calibration notch represents a defect, nor do they confirm that defective pipe and tubing will be rejected or repaired according to this criterion. ...

Open

11088

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are confirmed to be per the applicable ASTM standard (ASTM A999), with no deviations or overrides specified in the customer documentation. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDA...

Open

11089

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, ensuring full traceability to melt and heat treatment lot. Marking methods include heat number and DMV lot number as required by the standards and plant procedures. Source: DMV_STANDARD_BOOK/0...

Open

11090

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 explicitly states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NO...

Open

11091

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

11092

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

11093

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, fulfilling the qualification requirement for the specified size and product f...

Open

11094

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

11095

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certification ...

Open

11096

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and n...

Open

11097

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

11098

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782; no confirmation of QTR/MPCR availability. Requirement for qualification to both NORSOK M-650/ISO 17782 and documentation availability is not fulfilled. Source: DMV_STANDARD_BO...

Open

11099

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

11100

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11101

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed by heat analysis with supplier certification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Dige...

Open

11102

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

11103

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for each heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

11104

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, directly referencing Table 3 for sampling as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM ...

Open

11105

4.1

AI

No

add date

Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, are fulfilled for DMV 25.7N. The...

Open

11106

4.2

AI

No

add date

Tensile testing is performed at room temperature in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

11107

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11108

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

11109

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the requested pipe dimensions (WT > 6mm), fulfilling the requirement. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

11110

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for required transverse testing. Source: DM...

Open

11111

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants after final polishing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

11112

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

11113

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

11114

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

11115

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOO...

Open

11116

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

11117

4.4.2

AI

No

add date

The available specifications allow isolated intermetallic precipitates below 10 µm if not distributed over the whole specimen, but do not confirm a zero-tolerance policy for intermetallics/precipitates when CVN testing cannot be completed, as require...

Open

11118

4.4.3

AI

No

add date

Ferrite content is checked as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite determination per ASTM E562 or E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

11119

4.4.3

AI

No

add date

Microstructure must be examined per ISO 17781 at ≥400X magnification, etched to detect intermetallic phases, nitrides, and carbides. Structure must be basically free from intermetallic precipitates; isolated precipitates allowed if not distributed an...

Open

11120

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

11121

4.5

AI

No

add date

No explicit confirmation of ASTM G48 Method 'A' (50°C, 24h) corrosion testing in accordance with ISO 17781 is provided in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

11122

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and complies with NORSOK and ASTM A790 qualification processes. Source: DMV_STANDARD_BOOK/...

Open

11123

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per NORSOK MDS D51 Rev 06 corrosion test (ISO 17781: G48 Method A @ 50°C, 24h). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

11124

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

11125

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

11126

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but compliance with specific NDE requirements of NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 is not demonstrated. For OD 219.1 mm, eddy current testing is not feasible at Montbard, and hydrostatic/ultrasonic tests ...

Open

11127

5.2

AI

No

add date

No provided document confirms that indications greater than the calibration notch are classified as defects requiring rejection or repair, nor that NDE with this acceptance criterion is standard for the requested dimension at Montbard. NDE feasibilit...

Open

11128

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding TechnipFMC specification indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A 376-0...

Open

11129

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11130

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, ensuring full traceability to melt and heat treatment lot. Marking methods include heat number and DMV lot number as required by the standards and plant procedures. Source: DMV_STANDARD_BOOK/0...

Open

11131

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

11132

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

11133

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

11134

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

11135

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, are provided as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

11136

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D...

Open

11137

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for DMV 25.7N seamless pipe, fulfilling the requirement. Source: Digest NORSOK MDS D51 Rev 06.docx

Open

11138

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice and refining method, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel produ...

Open

11139

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

11140

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N (up to WT 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

11141

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

11142

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11143

3.1

AI

No

add date

DMV 25.7N (UNS S32760) chemical composition matches the requirements of Table 2 and complies with ASTM A790 and NORSOK MDS D51 Rev 06, including PREN ≥ 40 and all specified element limits. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest ...

Open

11144

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

11145

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produc...

Open

11146

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

11147

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specifi...

Open

11148

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1 at room temperature, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

11149

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

11150

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

11151

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, with minimum absorbed energy values for transverse and longitudinal specimens, and the specified pipe dimensions allow for required transverse Charpy V-notch testin...

Open

11152

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

11153

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

11154

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

11155

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded as required. Source...

Open

11156

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

11157

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

11158

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm, but the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Zero-tolerance is not stated, so the requirement is not fulf...

Open

11159

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

11160

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Structure must be basically free from intermetallic precipitates, with isolated precipitates allowed if ...

Open

11161

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

11162

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

11163

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, chemical composition, ferrite content, corrosion, impact requirements, and M-650 qualification for the specified wall thickn...

Open

11164

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781 (G48 Method A @ 50°C, 24h). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Diges...

Open

11165

5.1

AI

No

add date

No evidence provided regarding qualification or certification of NDE personnel to ISO 9712 level II or III, or their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montba...

Open

11166

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

11167

4.4.1

AI

No

add date

No evidence of etching with 20-40% NaOH or KOH solution or other suitable etchant as per ISO 17781 Appendix B for micrographic examination; only grain size measurement for austenitic materials is addressed, not duplex/super-duplex steels or the speci...

Open

11168

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. For the specified OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at extra cost. ...

Open

11169

5.2

AI

No

add date

No provided documentation confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor is this acceptance criterion explicitly stated or confirmed as feasible for the specified pipe size at Mo...

Open

11170

6.0

AI

No

add date

Dimensional tolerances for the specified pipe are per ASTM A790 and its referenced standards (e.g., ASTM A999), with no overriding requirements from TechnipFMC identified. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General informatio...

Open

11171

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11172

8.0

AI

No

add date

Marking per ASTM A790 and standard practices at Montbard include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDA...

Open

11173

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

11174

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

11175

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

11176

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

11177

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

11178

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

11179

10.2

AI

No

add date

NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, heat number, actual chemical analysis, solution annealing temperature/holding time/quench medium, and results of all required metallurgical and non-destructive testing are not ...

Open

11180

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 Rev. 6, including relevant chemical, mechanical, and testing requirements. Manufacturing is also qualified to NORSO...

Open

11181

1.0

AI

No

add date

No evidence is provided that the supplier is qualified in accordance with both NORSOK M-650 and ISO 17782 for the exact product supplied, nor is there confirmation of the availability of the full Qualification Test Record/MPCR for review by TechnipFM...

Open

11182

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N within specified wall thickness limits, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BO...

Open

11183

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N complies with the required chemical analysis. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NOR...

Open

11184

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the requested WT of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest ...

Open

11185

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782, and procedures ensure free circulation of heating and cooling media during hea...

Open

11186

4.1

AI

No

add date

There is no evidence that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is carried out for each heat and heat treatment lot as required by ASTM A790; available documents do not confirm compliance with this r...

Open

11187

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

11188

4.1

AI

No

add date

Test sampling requirements for test direction (longitudinal/transverse), CVN impact testing, and detailed thickness locations are not fully specified or confirmed; CVN impact testing is not addressed and tensile test direction is unclear or only avai...

Open

11189

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

11190

4.2

AI

No

add date

Mechanical property values required (tensile strength, yield strength, elongation, hardness) are not confirmed in the provided documents, and referenced grades do not meet the specified requirements for DMV 25.7N (S32760/S32750). Source: DMV_STANDARD...

Open

11191

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions, exceeding the minimum wall thickness required by ASTM and ISO standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02...

Open

11192

4.3

AI

No

add date

Pipe wall thickness of 18.26 mm allows for transverse impact specimens, meeting the specified impact property requirements for both transverse and longitudinal directions at -46°C as per the specification. Source: DMV_STANDARD_BOOK/12-03-02 - Impact ...

Open

11193

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination per ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels; only grain size measurement for austenitic materials is discussed, which is not appli...

Open

11194

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

11195

4.4.2

AI

No

add date

The microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

11196

4.4.2

AI

No

add date

No evidence of micrographs at 400x or documentation of the presence and location of intermetallic phases is provided or addressed in the relevant documents. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Microgr...

Open

11197

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included at actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness if intermetallic phases a...

Open

11198

4.4.2

AI

No

add date

No relevant documents address the requirement to report centerline intermetallic stringers or base acceptance on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I.doc, DMV_STANDARD_BOOK/12...

Open

11199

4.4.2

AI

No

add date

Documents allow isolated intermetallic precipitates below 10µm and do not fully prohibit all intermetallic phases/precipitates if CVN testing cannot be completed, as required by the specification. No document fully satisfies the requirement for compl...

Open

11200

4.4.3

AI

No

add date

No information is provided confirming ferrite content determination per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781; only grain size measurement is discussed, not ferrite content measurement or the specified standards. Source: DMV_STANDARD...

Open

11201

4.4.3

AI

No

add date

No acceptance criteria for micrographic examination are specified or evidenced for DMV 25.7N in the provided sources; only procedures and standards for measurement are described without explicit criteria or required values for the order or grade. Sou...

Open

11202

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11203

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or confirmed in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

11204

4.5

AI

No

add date

No acceptance criteria for metallurgical properties are specified or detailed for DMV 25.7N or A790 in the provided documents; section 4.0 is not present and no explicit criteria are given for the required grade or standard. Source: DMV_STANDARD_BOOK...

Open

11205

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria: no pitting at 20X magnification and weight loss < 1.0 g/m², matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

11206

5.1

AI

No

add date

No provided documents address the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDARD_B...

Open

11207

5.2

AI

No

add date

No confirmation that 100% ultrasonic testing will be performed according to ASTM E213 or ISO 10893-10, or that reference notches will meet the specified criteria after all processing steps. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non d...

Open

11208

5.2

AI

No

add date

Dye penetrant testing is performed on tube ends and bevels on request, matching the client inquiry, and 100% qualitative anti-mixing PMI is conducted on standard production at Montbard, fulfilling NDE acceptance criteria for DMV 25.7N grade. Source: ...

Open

11209

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

11210

5.2

AI

No

add date

No provided document confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair for the specified product and dimension; NDE feasibility and acceptance criteria are not explicitly addressed for t...

Open

11211

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed as per the applicable ASTM standards (including ASTM A790 with A999 for tolerances) for the relevant size range, with no deviations or exceptions noted in the specification or part report/d...

Open

11212

7.0

AI

No

add date

Requirement is fulfilled as both ASTM A790 and NORSOK MDS S01 standards specify that finished pipes shall be white pickled or bright annealed. Source: Digest ASTM A 790.docx, Digest NORSOK MDS S01 Rev 05 .docx

Open

11213

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

11214

10.0

AI

No

add date

No evidence is provided of an ISO 9001 quality-assurance system certified by a competent EEA body with a specific assessment for materials at the Montbard plant. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Cer...

Open

11215

10.1

AI

No

add date

No evidence provided that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body with specific assessment for materials, as required. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification...

Open

11216

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

11217

10.2

AI

No

add date

No evidence is provided that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205. No confirmation of SIR205 compliance or traceability is present in the reviewed documents. Source: DMV_STANDARD_BOOK/14-01 -...

Open

11218

10.2

AI

No

add date

Mill Inspection Certificate is issued according to EN 10204 Type 3.1, with compliance to ASTM A790 and NORSOK M-630 implied for the specified grades and norms. Source: 14-03 - Certification Montbard plant.doc

Open

11219

10.2

AI

No

add date

None of the reviewed documents provide the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters...

Open

11220

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with explicit confirmation of compliance for chemical, mechanical, and testing requirements for this grade ...

Open

11221

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

11222

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of availability of Qualification Test Record/MPCR for review by TechnipFMC. MST-Tubes is only M-650 accredited (not ISO 17782). ...

Open

11223

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 (or ISO 17782) procedures, fulfilling the requirement for manufacturer and process qualification and co...

Open

11224

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N complies with the required chemical analysis in Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

11225

3.1

AI

No

add date

DMV 25.7N (UNS S32760) is manufactured according to NORSOK M-650 qualified procedures, with accreditation covering the requested wall thickness of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-0...

Open

11226

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling (water quenching) per ASTM A790, furnaces comply with NORSOK M-650/ISO 17782, and pipe placement ensures free circulation of heating/cooling media during heat treatment including acc...

Open

11227

4.1

AI

No

add date

No document confirms that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790. Testing frequencies, lot definitions, and required test type...

Open

11228

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

11229

4.1

AI

No

add date

Test sampling details such as test direction for tensile and CVN tests, and required thickness locations, are not explicitly confirmed. No evidence that all specified tests (tensile, hardness, CVN, corrosion, microstructure) are performed on prolonga...

Open

11230

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4. Hardness testing is also performed as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

11231

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required in Table 4 are not confirmed or are not met in the provided documents for DMV 25.7N (UNS S32760). Standard values are referenced but not specified, and prope...

Open

11232

4.3

AI

No

add date

No evidence that Charpy V-notch testing is performed or meets ASTM A370, ASTM A1058, ISO 148-1, or Table 5 requirements for the specified product or plant context. Feasibility rules are mentioned, but compliance and execution are not confirmed. Sourc...

Open

11233

4.3

AI

No

add date

Pipe with OD 219.1 mm and WT 18.26 mm allows both longitudinal and transverse Charpy V-notch specimens; impact property requirements in Table 5 can be fulfilled. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

11234

1.0

AI

No

add date

DMV 25.7N seamless pipe is compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, fulfilling all specified mechanical, chemical, corrosion, and qualification requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11235

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination according to ISO 17781 or specification of the required etchant solution for 25 Cr Duplex stainless steels; only grain size measurement for austenitic materials is addressed, not duplex steels...

Open

11236

4.4.1

AI

No

add date

No information confirming the use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination or to reveal ferrite balance and intermetallic phases is provided. Source: DMV_STANDARD_BOOK/12 - S...

Open

11237

4.4.2

AI

No

add date

The micrographic examination section requires the microstructure to be basically free from intermetallic precipitates, allowing isolated precipitates if not homogeneously distributed and each is below 10 μm, matching the client's requirement exactly....

Open

11238

4.4.2

AI

No

add date

No information or procedures are provided regarding the detection, recording, or micrographic documentation (at 400x or higher) of intermetallic phases; the requirement is not addressed. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destruct...

Open

11239

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, reported at actual magnification and including a scale bar, if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - ...

Open

11240

4.4.2

AI

No

add date

No provided documents address the reporting or acceptance criteria for centerline intermetallic stringers or link acceptance to CVN and corrosion test results in their presence. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I.doc...

Open

11241

4.4.2

AI

No

add date

Referenced documents allow isolated intermetallic precipitates below 10µm and do not fully prohibit intermetallic phases/precipitates if CVN testing cannot be completed, which does not meet the client's zero-tolerance requirement in such cases. No do...

Open

11242

4.4.3

AI

No

add date

No evidence of ferrite content measurement by ASTM E 562, ASTM E 1245, or ISO 17781 is provided; only grain size measurement is discussed, which does not fulfill the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive test...

Open

11243

4.4.3

AI

No

add date

No acceptance criteria for micrographic examination are specified or addressed in the provided documents for DMV 25.7N or the specific inquiry; only procedures and general requirements are mentioned without defining required values or ranges for meta...

Open

11244

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11245

4.5

AI

No

add date

No explicit acceptance criteria for metallurgical properties are specified for DMV 25.7N or A790 in the provided documents. Requirement not fulfilled. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NO...

Open

11246

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) requires no pitting at 20X magnification and weight loss < 1.0 g/m², matching client requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

11247

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDARD_BOOK/...

Open

11248

5.2

AI

No

add date

No confirmation that 100% ultrasonic testing for longitudinal defects will be performed according to ASTM E213 or ISO 10893-10, nor mention of reference notches as per Figure 3 of ASTM E213 or testing after all processing steps. Source: DMV_STANDARD_...

Open

11249

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11250

5.2

AI

No

add date

Dye penetrant testing is performed on tube ends and bevels as per standard practice, and 100% qualitative anti-mixing PMI is conducted on standard production, fulfilling the NDE acceptance criteria in the absence of additional specific customer requi...

Open

11251

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor that the required NDE is applied as standard for the specified product and size. Source: DMV_STA...

Open

11252

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed as per the applicable ASTM standards (including ASTM A790/A999) for the specified product dimensions, with no deviations or special requirements noted from TechnipFMC, fulfilling the requir...

Open

11253

7.0

AI

No

add date

Pipes must be pickled or bright annealed per ASTM A790 and are required to be white pickled or bright annealed as a standard for MST-Tubes per NORSOK MDS S01 Rev 05, directly fulfilling the requirement for finished pipes to be white pickled or bright...

Open

11254

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

11255

10.0

AI

No

add date

No evidence of an appropriate quality-assurance system (such as ISO 9001 certification by a competent EEA body) is provided for the Montbard plant or manufacturer. No certification details or proof of compliance are included in the relevant documents...

Open

11256

10.1

AI

No

add date

No evidence that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body as required by the specification or that required documentation will be submitted to TechnipFMC for approval. Source: DMV_STANDARD_BOOK/14-03...

Open

11257

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, demonstrating qualification for the size and product form. Source: DMV_STANDA...

Open

11258

10.2

AI

No

add date

No evidence that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC is provided. No explicit mention of SIR205 or confirmation of transmission and traceability is found in the relevant documents. Source: ...

Open

11259

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control for mill inspection, which fulfills the requirement. Standard practice implies inclusion of information required by ASTM A790 and NORSOK M-630. Source: D...

Open

11260

10.2

AI

No

add date

None of the provided documents include the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or results of meta...

Open

11261

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; full qualification to both NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR is not confirmed. Source: DMV_STANDARD_BO...

Open

11262

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

11263

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11264

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed by heat analysis and supplier certification for DMV material. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

11265

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured ...

Open

11266

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

11267

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling as outlined in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

11268

4.1

AI

No

add date

Tensile, hardness, CVN (transverse or longitudinal if not possible), corrosion, and microstructure tests are performed on seamless pipes per ASTM A790 and NORSOK MDS D51, with test directions and thickness locations as specified. The ordered pipe dim...

Open

11269

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, meeting the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. DMV 25.7N complies with these requirements. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

11270

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

11271

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

11272

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C, including minimum absorbed energy values and sub-size specimen reduction factors. The specified pipe dimensions allow for required transverse and longitudinal Charpy...

Open

11273

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH solution after final polishing, fulfilling the requirement for metallographic preparation and examin...

Open

11274

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

11275

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

11276

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

11277

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

11278

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

11279

4.4.2

AI

No

add date

No provided document confirms that intermetallic phases and/or precipitates are completely absent if CVN testing cannot be completed; the available digest allows isolated precipitates, which does not meet the stricter client requirement. Source: DMV_...

Open

11280

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

11281

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impa...

Open

11282

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS ...

Open

11283

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

11284

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

11285

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, meeting the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest...

Open

11286

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, or their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montba...

Open

11287

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects is performed in accordance with ASTM E213 or ISO 10893-10 for the required pipe dimensions. Acceptance of ASTM E213 implies compliance with calibration notch requirements and testing after all processi...

Open

11288

5.2

AI

No

add date

NDE per ASTM A790 is partially addressed (hydrostatic or NDE per ASTM A999), but there is no confirmation of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements. For the requested OD (219.1 mm), eddy current...

Open

11289

5.2

AI

No

add date

No provided document explicitly confirms that indications greater than the calibration notch are classified as defects requiring rejection or repair per the requirement; NDE acceptance criteria are not clearly stated or confirmed for the specified pr...

Open

11290

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790/A999) for the specified pipe, with no overriding customer specification noted. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-0...

Open

11291

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11292

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

11293

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

11294

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

11295

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

11296

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO 17782 manufacturing summary or QTR number, are provided and meet the requirement for transmission and traceability to TechnipFMC as per ...

Open

11297

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

11298

10.2

AI

No

add date

EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MPCR number, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the act...

Open

11299

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, testing, and qualification requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11300

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not to ISO 17782, and there is no evidence of QTR/MPCR documentation availability as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11301

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

11302

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard and required for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS...

Open

11303

3.1

AI

No

add date

Chemical composition for UNS S32760 conforms to Table 2 of ASTM A790, matching the specified limits, with heat analysis and supplier certification provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-0...

Open

11304

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

11305

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

11306

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling as outlined in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

11307

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per ASTM A790 and NORSOK r...

Open

11308

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with tensile and hardness properties meeting Table 4 requirements for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spec...

Open

11309

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 06 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's Table 4 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

11310

4.3

AI

No

add date

Charpy V-notch testing as per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests...

Open

11311

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energy values for transverse and longitudinal directions, and the specified pipe dimensions allow for required transverse Charpy V-notch testin...

Open

11312

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

11313

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-...

Open

11314

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

11315

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

11316

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

11317

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

11318

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

11319

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11320

4.4.3

AI

No

add date

Ferrite content is determined per ASTM E1245 by default and ASTM E562 on request, both in accordance with ISO 17781, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Diges...

Open

11321

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

11322

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

11323

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

11324

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11325

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per NORSOK MDS D51 Rev 06 (ISO 17781, G48 Method A). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

11326

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712 or equivalent. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing...

Open

11327

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

11328

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT) is confirmed, but NORSOK M-630 MDS D51 and M-650/ISO 17782 NDE requirements are not addressed. For OD 219.1 mm at Montbard, eddy current testing is not feasible, hydrostatic and ultrasonic tests are onl...

Open

11329

5.2

AI

No

add date

No provided documentation explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor is the required NDE process feasible for the specified OD at the plant. Source: DMV_STANDAR...

Open

11330

6.0

AI

No

add date

Dimensional tolerances are specified as per ASTM A790/A999 for the relevant size, with no overriding TechnipFMC specification indicated. Requirement is fulfilled per applicable ASTM standard as requested. Source: DMV_STANDARD_BOOK/07-01 - General inf...

Open

11331

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11332

8.0

AI

No

add date

Marking per ASTM A790 §16 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/1...

Open

11333

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

11334

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

11335

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11336

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dige...

Open

11337

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

11338

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

11339

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAN...

Open

11340

10.2

AI

No

add date

EN 10204 3.1 certificates will include most required information (NORSOK M-650/ISO 17782 QTR number, steel melting practice, heat treatment, etc.), but only the country of origin of the steel supplier is provided, not the actual steel producer's name...

Open

11341

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03...

Open

11342

1.0

AI

No

add date

Supplier is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to certain wall thicknesses) but not accredited to ISO 17782, as explicitly required. No confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest N...

Open

11343

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process follows M-650 (or ISO 17782) qualified procedures, fulfilling the requirement for manufacturer and process qualification per NORSOK M-65...

Open

11344

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11345

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PREN ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11346

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

11347

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

11348

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

11349

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests are performed at specifie...

Open

11350

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11351

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Hardness testing is also performed as specified. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

11352

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

11353

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for 18.26mm wall thickness and 219.1mm OD pipe as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impac...

Open

11354

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements at -466C, with minimum absorbed energy values of 45 J (transverse average), 35 J (transverse single), 65 J (longitudinal average), and 50 J (longitudinal single), including sub-size re...

Open

11355

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

11356

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination and matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

11357

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

11358

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

11359

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report at actual magnification and with a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/...

Open

11360

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

11361

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required if CVN testing cannot be completed due to geometry or size, so the requirement is not fully fulfilled. Sourc...

Open

11362

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

11363

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosio...

Open

11364

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

11365

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

11366

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including destructive, micrographic, corrosion tests, ferrite content, heat treatment, and manufacturing process requirements. Source: DMV_STANDARD_BOOK/02...

Open

11367

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

11368

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement is not fulfilled based on the available information. Sou...

Open

11369

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is confirmed, with testing performed after all processing steps. Calibration is expected to follow ASTM E213 Figure 3 as the standard is referenced. Pipe dimensions are wi...

Open

11370

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not addressed or confirmed as fulfilled. For the requested OD (219.1 mm), eddy current and ultrasonic testing are only available at extra cost and not confirmed as ...

Open

11371

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor that such NDE acceptance criteria are standardly available for the requested si...

Open

11372

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are confirmed to be per the applicable ASTM standards (including A999) for the specified size, with no overriding TechnipFMC requirements identified. Source: DMV_STANDARD_BOOK/07-01 - General information.doc,...

Open

11373

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11374

8.0

AI

No

add date

Marking per ASTM A790 and plant marking methods ensure mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

11375

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

11376

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

11377

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

11378

10.1

AI

No

add date

Supplier is M-650 accredited for DMV25.7N up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used for the specified product form and size. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

11379

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to the delivered products, fulfilling the documentation and traceability requirement as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

11380

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782, and there is no evidence of QTR/MPCR availability as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11381

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and will include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary o...

Open

11382

10.2

AI

No

add date

Most required documentation and certification items (NORSOK M-650/ISO 17782 identification, steel producer, heat number, chemical analysis, solution annealing details, metallurgical and NDT results) are not evidenced. The EN 10204 3.1 certificate is ...

Open

11383

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

11384

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but lacks ISO 17782 accreditation; no evidence of QTR/MPCR availability or full compliance with the requirement for both standards and documentation review by TechnipFMC. Source: DMV_STANDARD_BOOK/0...

Open

11385

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

11386

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11387

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the requirement table and DMV material composition conforms to this specification with heat analysis and supplier certification performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

11388

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition, and compliance with these standards ensures prope...

Open

11389

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

11390

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

11391

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled per NORSOK MDS D51/ASTM A790. Fo...

Open

11392

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with mechanical properties meeting Table 4 requirements (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%), and hardness testing is also performed as specified. Source: DMV_STANDARD_...

Open

11393

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

11394

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

11395

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal. The specified pipe wall thickness (18.26 mm) allows both longitudinal and t...

Open

11396

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

11397

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

11398

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

11399

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

11400

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

11401

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

11402

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. No evidence of stricter compliance is provided. Source: DM...

Open

11403

4.4.3

AI

No

add date

Ferrite content is determined per ASTM E562 or by image analysis according to ASTM E1245, performed in accordance with ISO 17781, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

11404

4.4.3

AI

No

add date

Micrographic examination per ISO 17781 is specified with etching, minimum 400X magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact...

Open

11405

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

11406

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including chemical composition (PRE ≥ 40), mechanical properties, microstructure, ferrite content (35-60%), and corrosion resistance; manufacturing process is M-650 quali...

Open

11407

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A @ 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and is confirmed compliant with these requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

11408

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

11409

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 or ISO 10893-10 is feasible for the specified pipe dimensions and is supported by available equipment and accepted standards. Source: DMV_STANDARD_BOOK/12 - Special Testing...

Open

11410

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no evidence of compliance with additional NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782 NDE requirements. For the requested OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic te...

Open

11411

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is classified as a defect requiring rejection or repair, nor is there confirmation that the specified NDE acceptance criterion is applied for the re...

Open

11412

6.0

AI

No

add date

Dimensional tolerances for the specified pipe are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790), with no overriding TechnipFMC part report or drawing indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_...

Open

11413

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11414

8.0

AI

No

add date

Marking is performed according to ASTM A790, requiring full traceability to melt and heat treatment lot. Marking methods include heat number and DMV lot number, ensuring traceability as required by the specification. Source: DMV_STANDARD_BOOK/02-04-0...

Open

11415

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 explicitly states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NO...

Open

11416

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

11417

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers as specified in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

11418

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demonst...

Open

11419

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

11420

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

11421

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C, with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal. The specified pipe dimensions allow ...

Open

11422

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH solution after final polishing, fulfilling the requirement for metallographic preparation and examin...

Open

11423

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and n...

Open

11424

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. M-650 qualification and all relevant testing requirements are met. Source: DMV_STANDARD_BOOK/02-04-03 ...

Open

11425

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782, as explicitly required. No evidence provided for QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11426

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

11427

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11428

3.1

AI

No

add date

Referenced documents confirm required compliance with chemical composition limits for S32760 per ASTM A790 and NORSOK MDS D51, but do not provide explicit chemical composition values or direct evidence that the specified limits for each element are m...

Open

11429

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

11430

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

11431

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, fulfilling the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed ...

Open

11432

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, in compliance with ASTM A790 a...

Open

11433

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, meeting the tensile and maximum hardness properties of Table 4 for DMV 25.7N, as required by NORSOK MDS D51. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

11434

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

11435

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

11436

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

11437

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

11438

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

11439

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

11440

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

11441

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

11442

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

11443

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

11444

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11445

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the applicable standards or documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.d...

Open

11446

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content...

Open

11447

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

11448

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

11449

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

11450

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR availability. Full compliance with NORSOK M-650/ISO 17782 is not demonstrated for the exact product supplied as required....

Open

11451

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, DMV_STANDARD_BOOK/02-04-03 - D...

Open

11452

5.2

AI

No

add date

NDE per ASTM A790 is covered, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD (219.1 mm), standard NDE (eddy current, ultrasonic, hydrostatic) is not ava...

Open

11453

5.2

AI

No

add date

No provided documentation explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor that the required NDE acceptance criteria will be applied as standard for the specified pro...

Open

11454

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no override specified in the customer requirements or context. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK...

Open

11455

7.0

AI

No

add date

ASTM A790 (6.1.3) and NORSOK MDS D51 (§13) both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11456

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790, requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring compliance with the requirement for traceability. Source: DMV...

Open

11457

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

11458

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

11459

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

11460

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and QTR number is included as per M-650 qualification, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MCPR ...

Open

11461

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with full traceability to the delivered products, fulfilling SIR205 documentation requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

11462

10.2

AI

No

add date

Certification is provided to EN 10204 Type 3.1 and includes all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control for mill inspection and reference to the relevant standards throughout the specification. Source: D...

Open

11463

10.2

AI

No

add date

EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin (not the specific steel producer) is provided. There is no explicit confirmation that h...

Open

11464

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03...

Open

11465

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to 31.75 mm WT, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

11466

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical analysis conforms to the specified table for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11467

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat to ensure compliance. Source: 02-03...

Open

11468

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

11469

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

11470

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-0...

Open

11471

4.1

AI

No

add date

All required tests (tensile, hardness, CVN, corrosion, microstructure) are performed on DMV 25.7N seamless pipes as per NORSOK MDS D51/ASTM A790, with correct test directions and locations. For the specified pipe dimensions, transverse CVN specimens ...

Open

11472

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

11473

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

11474

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and standards; requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/1...

Open

11475

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements: Charpy V-notch testing at -46°C with minimum absorbed energy values (transverse: 45 J average/35 J single, longitudinal: 65 J average/50 J single if transverse not possible) for wall ...

Open

11476

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

11477

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchants to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is explicitly required for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

11478

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

11479

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STANDA...

Open

11480

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

11481

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

11482

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is...

Open

11483

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

11484

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

11485

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

11486

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation or standards list. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

11487

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

11488

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

11489

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

11490

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and pipe dimensions are within equipment capability. Testing after all processing is standard practice. Source: DMV...

Open

11491

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not validated; only ASTM A790/A999 NDE is confirmed. For the specified OD, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available...

Open

11492

5.2

AI

No

add date

None of the reviewed documents explicitly state that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor do they confirm the feasibility of such NDE acceptance criteria for the ...

Open

11493

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specifications from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A...

Open

11494

8.0

AI

No

add date

Marking is per ASTM A790 §14 and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-...

Open

11495

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

11496

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

11497

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and the QTR number is included in the certificate, fulfilling the requirement for supplier qualification documentation per SIR131. Source: DMV_STANDARD_BOOK/0...

Open

11498

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

11499

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control for mill inspection and referencing the relevant standards and documentation scope. Source: DMV_STANDARD_BOOK/0...

Open

11500

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, steel melting practice, refining method, heat treatment condition, heat number, chemical analysis, and test results, but only the co...

Open

11501

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

11502

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical analysis complies with Table 2 requirements for DMV 25.7N seamless pipe per ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest N...

Open

11503

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PREN ≥ 40, and matches the NORSOK MDS D51 Rev 06 and ASTM A790 specifications for all listed elements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-0...

Open

11504

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is qualified to NORSOK M-650/ISO 17782, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by complian...

Open

11505

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot, with 'lot' defined as per ASTM A790, fulfilling the requirement for testing per heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 -...

Open

11506

4.1

AI

No

add date

Test specimens sampling is performed according to Table 3, with specified frequency matching the requirement for sampling as per Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03...

Open

11507

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not feasible), and corrosion/microstructure tests, with specified locations and directions, is fulfilled for DMV 25.7N per ...

Open

11508

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and material meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest N...

Open

11509

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

11510

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for 18.26mm wall thickness and 219.1mm OD pipe as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impac...

Open

11511

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -466C, with minimum absorbed energy values for transverse and longitudinal directions, and the specified pipe dimensions allow for required transverse Charpy V-notch testing. Sourc...

Open

11512

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

11513

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination in accordance with the requirement. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

11514

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

11515

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

11516

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness when intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

11517

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria based on CVN and corrosion...

Open

11518

4.4.2

AI

No

add date

No provided documentation confirms a zero-tolerance policy for intermetallic phases and/or precipitates when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10µm, which does not meet the stricter client requi...

Open

11519

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

11520

4.4.3

AI

No

add date

Microstructure examination is performed as per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at a minimum magnification of 400X. Acceptance criteria: structure must be basically free from intermetallic precipitates (is...

Open

11521

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

11522

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

11523

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive, micrographic, corrosion tests, ferrite content, heat treatment, and M-650 qualification for the specified wall thickness range. Source: DMV_STANDAR...

Open

11524

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

11525

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

11526

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-...

Open

11527

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT) is detailed, but there is no explicit confirmation of compliance with NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782 requirements. Eddy current testing is not feasible for the specified OD at Montbard, ...

Open

11528

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor that this NDE acceptance criterion is applied as standard for the requested pro...

Open

11529

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specifications from TechnipFMC indicated. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances accor...

Open

11530

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed per ASTM A790 and white pickled or bright annealed per NORSOK MDS D51 Rev 06, fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: Digest ASTM A 790.docx, Di...

Open

11531

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

11532

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system as required by NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

11533

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

11534

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number as required for qualification for the size and product f...

Open

11535

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

11536

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and NORSOK M-650/ISO17782 manufacturing summary o...

Open

11537

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and results of all metallurgical and no...

Open

11538

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. M-650 qualification and all required tests and certifications are covered. Source: DMV_STANDARD_BOOK/0...

Open

11539

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of full qualification to both NORSOK M-650/ISO 17782 or availability of QTR/MPCR documentation for review as required by the ...

Open

11540

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, with manufacturing process qualified per NORSOK M-650 or ISO 17782 and meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

11541

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11542

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat, confirming conformity to the requireme...

Open

11543

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

11544

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with lot defined as in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

11545

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the specified frequency, fulfilling the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detai...

Open

11546

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled per NORSOK MDS D51/ASTM A790. Fo...

Open

11547

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with material meeting the specified tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

11548

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

11549

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

11550

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C (transverse: 45/35 J, longitudinal: 65/50 J, sub-size reduction factors) for thickness >6mm; the specified pipe dimensions allow for required testing directions and v...

Open

11551

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

11552

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

11553

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

11554

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are reported with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

11555

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

11556

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

11557

4.4.2

AI

No

add date

No evidence that intermetallic phases and/or precipitates are completely prohibited when CVN testing cannot be completed; current specifications allow isolated precipitates below 10μm, which does not meet the stricter client requirement. Source: DMV_...

Open

11558

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

11559

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

11560

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11561

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

11562

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

11563

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

11564

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source: DM...

Open

11565

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

11566

5.2

AI

No

add date

Compliance with NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 NDE requirements is not confirmed. Eddy current testing is not feasible for the specified OD, and hydrostatic/ultrasonic testing is only available at extra cost. Full-length dye pe...

Open

11567

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair; NDE acceptance criteria and feasibility for the specified size are not demonstrated for Montbard plant operations or in...

Open

11568

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding TechnipFMC specification indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A 376-0...

Open

11569

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11570

8.0

AI

No

add date

Marking is performed according to ASTM A790, including heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13...

Open

11571

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

11572

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

11573

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

11574

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demons...

Open

11575

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to delivered products, fulfilling the requirement for documentation to be transmitted to TechnipFMC and traceable as per SIR205. Source: DMV_STANDARD_BOOK/0...

Open

11576

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630 for the product in question. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certification ...

Open

11577

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of required metallurgical and non-destructive testing for the specific orde...

Open

11578

1.0

AI

No

add date

No evidence that the supplier is qualified according to both NORSOK M-650 and ISO 17782 or that Qualification Test Records/Manufacturer Procedure Conformity Records (QTR/MPCR) are available for review. Supplier is only accredited to NORSOK M-650, not...

Open

11579

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

11580

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11581

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat to ensure conformity. Source: Digest AS...

Open

11582

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling me...

Open

11583

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is carried out per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

11584

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

11585

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes meets requirements: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, all per ASTM A790 a...

Open

11586

4.2

AI

No

add date

Tensile testing is performed at room temperature with specified mechanical properties, and hardness testing is conducted. ASTM A790 requires tensile testing per ASTM A370, fulfilling the requirement for testing method and property compliance. Source:...

Open

11587

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

11588

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and meets the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impa...

Open

11589

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact test requirements at -46°C, including minimum absorbed energy values and sub-size specimen reduction factors. The specified pipe dimensions allow for required transverse and longitudinal Charpy V-n...

Open

11590

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

11591

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

11592

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

11593

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

11594

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness when intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

11595

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

11596

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10 µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. No source fully prohibits intermetallics as required. Sou...

Open

11597

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

11598

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

11599

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

11600

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified per NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

11601

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A @ 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and complies with these requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

11602

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source: DM...

Open

11603

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultr...

Open

11604

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled. Available documents only reference ASTM A790/A999 NDE, do not detail NORSOK-compliant NDE, or indicate that required NDE methods (eddy c...

Open

11605

5.2

AI

No

add date

None of the reviewed documents explicitly state that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair of pipe/tubing, nor do they confirm standard NDE availability for the specified ...

Open

11606

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding TechnipFMC specification indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a A 376-0...

Open

11607

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11608

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

11609

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

11610

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

11611

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the specified quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

11612

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

11613

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

11614

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided as standard and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 -...

Open

11615

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification, steel producer, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive testing are not fully ...

Open

11616

1.0

AI

No

add date

DMV 25.7N seamless pipes are 25 Cr Duplex stainless steel, manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, as confirmed by both the product table and technical digests. M-650 qualifica...

Open

11617

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - ...

Open

11618

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11619

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and DMV material composition conforms with supplier certification and heat analysis per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed diges...

Open

11620

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

11621

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, with test frequency specified as '1/lot'. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

11622

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-0...

Open

11623

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified th...

Open

11624

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

11625

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 and ASTM A790 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

11626

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, meeting the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 -...

Open

11627

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements, including Charpy V-notch testing at -46°C with minimum absorbed energy values (transverse: 45 J average, 35 J single; longitudinal: 65 J average, 50 J single if transverse not possibl...

Open

11628

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

11629

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH is specified for detecting ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

11630

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

11631

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

11632

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

11633

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

11634

4.4.2

AI

No

add date

NORSOK MDS D51 Rev 06 allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. No evidence of stricter prohibition is provided in the other...

Open

11635

4.4.3

AI

No

add date

Ferrite content is checked per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite determination by these methods in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

11636

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

11637

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

11638

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50°C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

11639

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as specified in NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO...

Open

11640

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

11641

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

11642

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is performed after all mechanical processing, heat treatment, and straightening, and the equipment covers the required pipe dimensions. Reference notches are introduced as per ASTM E213...

Open

11643

5.2

AI

No

add date

There is no explicit evidence that NDE acceptance criteria per ASTM A790, NORSOK M-630 MDS D51 Rev 6, or NORSOK M-650/ISO 17782 are fulfilled. Standard NDE methods (EC, UT, hydrostatic) are either not confirmed, only available at extra cost, or only ...

Open

11644

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor that such NDE acceptance criteria are standard or feasible for the specified pi...

Open

11645

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the requested pipe dimensions, with no deviations or special tolerances specified by the customer or TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.do...

Open

11646

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11647

8.0

AI

No

add date

Marking is performed per ASTM A790 §14 and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

11648

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11649

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

11650

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

11651

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

11652

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to the delivered products, fulfilling the documentation and traceability requirement per SIR205 and NORSOK M-650/ISO17782 qualification. Source: DMV_STANDAR...

Open

11653

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant specifications and manufacturing details as required by the client specification. So...

Open

11654

10.2

AI

No

add date

No provided documentation includes all required items: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or full metallurgical and non-destructive t...

Open

11655

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, Digest NORSOK MD...

Open

11656

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - D...

Open

11657

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

11658

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11659

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

11660

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is qualified to NORSOK M-650/ISO 17782, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by complian...

Open

11661

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for one set per heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

11662

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, directly referencing the required table for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - De...

Open

11663

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests, with specified locations and directions, is fulfilled for DMV 25.7N per ...

Open

11664

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1 at room temperature, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

11665

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

11666

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

11667

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, with minimum absorbed energy values for both transverse and longitudinal specimens, and the specified pipe dimensions allow for both test orientations as required. ...

Open

11668

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

11669

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

11670

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

11671

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

11672

4.4.2

AI

No

add date

Micrographs at a minimum magnification of 400x are taken and reported at actual magnification with a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

11673

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

11674

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases or precipitates if CVN testing cannot be completed due to geometry or size, so the requirement is not fully met. S...

Open

11675

4.4.3

AI

No

add date

Ferrite content is checked per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite determination by these methods in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

11676

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Structure must be basically free from intermetallic precipitates; isolated precipitates allowed if not d...

Open

11677

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

11678

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite content, and microstructure requirements, and is qualified according to NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/0...

Open

11679

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per NORSOK MDS D51 Rev 06 (ISO 17781, G48 Method A). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

11680

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructiv...

Open

11681

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed on the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - U...

Open

11682

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. For the requested OD (219.1 mm), eddy current testing is not feasible, and hydrostatic or ultrasonic testing is only available at extra co...

Open

11683

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor that such NDE acceptance criteria are standardly performed or feasible for the requested dimensi...

Open

11684

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no deviations or special tolerances specified for the requested size. Requirement is fulfilled as tolerances are confirmed to follow ASTM s...

Open

11685

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11686

8.0

AI

No

add date

Marking is per ASTM A790 §14 and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-...

Open

11687

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

11688

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

11689

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

11690

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, and QTR number is included as per M-650 qualification, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MCPR...

Open

11691

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to the delivered products, fulfilling the documentation and traceability requirement per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

11692

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control for mill inspection as per specification requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Diges...

Open

11693

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible and meets requirements for the specified pipe dimensions (OD 219.1 mm, WT 18.26 mm). Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-0...

Open

11694

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of required metallurgical and non-destructive testing. Only general practic...

Open

11695

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 Rev. 6. Both standards are explicitly referenced and the grade is listed as qualified for production. Source: DMV_S...

Open

11696

1.0

AI

No

add date

No evidence is provided that the supplier is qualified to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor that the full Qualification Test Record/MPCR is available for review as required. MST-Tubes is accredited to NORSOK M-650 fo...

Open

11697

3.0

AI

No

add date

MST-Tubes F is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, with manufacturing process qualified per NORSOK M-650 (or ISO 17782) and meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

11698

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N complies with the required chemical analysis per Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

11699

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the inquiry's wall thickness of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

11700

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed per ASTM A790, with manufacturing process and furnaces qualified according to NORSOK M-650 or ISO 17782, ensuring compliance with requirements including free circulation...

Open

11701

4.1

AI

No

add date

There is no evidence that impact, tensile, hardness, corrosion testing, and microstructure examinations are performed for each heat and heat treatment lot as defined in ASTM A790. Testing frequency, lot definition, and compliance with the full set of...

Open

11702

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

11703

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no evidence for CVN impact, hardness, corrosion, or microstructure tests, nor for required test directions or sampling locations. Requirement is not fully fulfilled. Source: DMV_STANDARD_BOOK/0...

Open

11704

4.2

AI

No

add date

Tensile testing is performed in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 ...

Open

11705

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required for DMV 25.7N are not confirmed in the provided sources; relevant data is missing or not applicable to the specified grade and requirements. Source: DMV_STAN...

Open

11706

4.3

AI

No

add date

Pipe dimensions allow for both longitudinal and transverse impact testing as required; impact test feasibility is confirmed for the specified wall thickness and diameter. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-0...

Open

11707

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation, ISO 17781, or the specified etching procedure for 25 Cr Duplex stainless steels. Grain size examination procedures for duplex grades are not addressed or are stated as not applicable. S...

Open

11708

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination of ferrite balance and intermetallic phases is provided.

Open

11709

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

11710

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided or addressed in the relevant documentation or comments. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/1...

Open

11711

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at 400x minimum magnification with a scale bar and actual magnification when intermetallic phases are not detected. Partial mention of 400x photos, bu...

Open

11712

4.4.2

AI

No

add date

No provided documents address the reporting or acceptance criteria for centerline intermetallic stringers or their relation to CVN and corrosion test results. Requirement not fulfilled by available information. Source: DMV_STANDARD_BOOK/12-03-03 - Gr...

Open

11713

4.4.2

AI

No

add date

Referenced documents allow isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not meet the stricter client requirement that prohibits any intermetallic phases and/or precipitates if CVN testing canno...

Open

11714

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided; only grain size measurement is addressed, not ferrite content determination by the specified methods or standards. Source: DMV_STANDARD...

Open

11715

4.4.3

AI

No

add date

No acceptance criteria for micrographic examination are provided or applicable for DMV 25.7N (super-duplex stainless steel); grain size examination is not required for this material and is not addressed in the referenced standards or digests for the ...

Open

11716

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STAND...

Open

11717

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided; only 'A790 NORSOK' is referenced, which does not confirm fulfillment of this requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tes...

Open

11718

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are provided in the requirement or referenced documents, making validation impossible. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSO...

Open

11719

4.5

AI

No

add date

Pitting corrosion test per ISO 17781, G48 Method A at 25°C for 24 hours is required, with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the client's requirements. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

11720

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDA...

Open

11721

5.2

AI

No

add date

No evidence is provided that 100% ultrasonic testing for longitudinal defects will be performed according to ASTM E213 or ISO 10893-10, nor that reference notches as per Figure 3 of ASTM E213 will be used for calibration as required. Dimensional feas...

Open

11722

5.2

AI

No

add date

Dye penetrant testing is performed on tube ends and bevels as required, and 100% qualitative anti-mixing PMI checks are standard, fulfilling the NDE acceptance criteria for the Montbard plant. Source: DMV_STANDARD_BOOK/12-02-05 - Dye penetrant inspec...

Open

11723

5.2

AI

No

add date

ASTM A790 (via ASTM A999) requires that any indication greater than the calibration notch is considered a defect and such pipes must be rejected or repaired, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

11724

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed as per the applicable ASTM standards (including ASTM A790/A999) for the relevant size range, with no deviations or TechnipFMC overrides indicated for the requested product. Source: DMV_STAN...

Open

11725

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and specified as white pickled or bright annealed in NORSOK MDS S01 Rev 05, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Sour...

Open

11726

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

11727

10.0

AI

No

add date

No evidence of an appropriate quality-assurance system (such as ISO 9001 certification by a competent EEA body) is provided for the Montbard plant or manufacturer. No certification details or compliance evidence are included in the referenced documen...

Open

11728

10.1

AI

No

add date

No evidence that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body as required by the specification or that required documentation will be submitted to TechnipFMC for approval. Source: DMV_STANDARD_BOOK/14-03...

Open

11729

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV25.7N up to WT = 31.75 mm, covering the requested WT = 18.26 mm, and the EN 10204 type 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number. So...

Open

11730

10.2

AI

No

add date

No evidence that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205 is provided in the referenced documents. Types of certificates and validation authorities are described, but the specific requirement for...

Open

11731

10.2

AI

No

add date

Material certificate is issued according to EN 10204 Type 3.1 and validated by Quality Control; standard practice implies inclusion of ASTM A790 and NORSOK M-630 information when required by the order/specification. Source: 14-03 - Certification Mont...

Open

11732

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C: minimum transverse (average 45 J, single 35 J) and longitudinal (average 65 J, single 50 J) absorbed energies, with reduction factors for sub-size specimens. The sp...

Open

11733

10.2

AI

No

add date

None of the provided documents include the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of m...

Open

11734

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, including mechanical, chemical, manufacturing, and testing requirements for 25 Cr Duplex stainless steel seamless pipes. So...

Open

11735

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence provided for full qualification to both NORSOK M-650/ISO 17782 or availability of QTR/MPCR documentation for review as required ...

Open

11736

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, fulfilling the requirement for manufacturer and process qualification and compliance with...

Open

11737

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11738

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - ...

Open

11739

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

11740

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

11741

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, directly referencing Table 3 for test specimen sampling as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02...

Open

11742

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations, is fulfilled per NORSOK MDS D51/ASTM A790. The or...

Open

11743

4.2

AI

No

add date

Tensile testing is performed at room temperature per NORSOK MDS D51 Rev 06, referencing ASTM A370/ISO 6892-1, with required tensile and maximum hardness properties met for DMV 25.7N. Hardness testing is also performed per ASTM A790. Source: DMV_STAND...

Open

11744

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

11745

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact ...

Open

11746

4.4.3

AI

No

add date

No evidence of ferrite content measurement by ASTM E 562, ASTM E 1245, or ISO 17781 is provided or addressed in the relevant documentation.

Open

11747

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, with specified etchants for intermetallic phases and ferrite balance applied after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

11748

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

11749

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

11750

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

11751

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

11752

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

11753

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm, while the requirement does not permit any intermetallic phases or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully fulfilled. Sourc...

Open

11754

4.4.3

AI

No

add date

Ferrite content is determined per ASTM E562 or by image analysis according to ASTM E1245, performed in accordance with ISO 17781, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

11755

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Acceptance: structure must be basically free from intermetallic precipitates (isolated precipitates allo...

Open

11756

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

11757

4.5

AI

No

add date

ASTM G48 Method 'A' corrosion testing at 50°C for 24h in accordance with ISO 17781 is not explicitly mentioned or evidenced; compliance cannot be confirmed based on the provided documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Mo...

Open

11758

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spe...

Open

11759

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

11760

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor are their roles and responsibilities as defined in ISO 9712 addressed. Source: DMV_STANDARD_BOOK/12-02-01 - Non d...

Open

11761

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultr...

Open

11762

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed. Standard NDE methods (EC, UT, hydrostatic) for the specified OD (219.1 mm) are either not feasible or only available at extra cost at Montbard, and f...

Open

11763

5.2

AI

No

add date

None of the relevant documents explicitly confirm that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor do they specify this NDE acceptance criterion for the requested produc...

Open

11764

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and referenced ASTM A999 for seamless pipe, with no overriding TechnipFMC specification indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according t...

Open

11765

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11766

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot, and the marking methods used (indelible ink and vibro-etching) include heat and lot numbers, ensuring compliance. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS ...

Open

11767

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

11768

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

11769

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

11770

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

11771

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to the products, fulfilling the requirement for documentation to be transmitted to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

11772

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary or QTR...

Open

11773

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and results of all metallurgical and non-destructive testi...

Open

11774

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Dig...

Open

11775

1.0

AI

No

add date

Supplier is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to certain wall thicknesses) but not accredited to ISO 17782, and there is no confirmation of QTR/MPCR documentation availability. Requirement for NORSOK M-650/ISO 17782 qualification ...

Open

11776

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N with the specified wall thickness, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - ...

Open

11777

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11778

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits and PREN requirement as specified in Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 6 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 R...

Open

11779

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

11780

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined by ASTM A790, with test frequency specified as 1/lot. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

11781

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

11782

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, is fulfilled for DMV 25.7...

Open

11783

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and the material meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dige...

Open

11784

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

11785

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness required for testing. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impac...

Open

11786

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C, with specified minimum absorbed energies for both transverse and longitudinal directions, and the requested pipe dimensions allow for required testing. Source: DMV_ST...

Open

11787

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH solution after final polishing, fulfilling the requirement for metallographic preparation and examin...

Open

11788

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is specified for showing ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

11789

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

11790

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

11791

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

11792

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

11793

4.4.2

AI

No

add date

No provided documentation fully prohibits intermetallic phases and/or precipitates if CVN testing cannot be completed; the closest reference allows isolated precipitates below 10μm, which does not meet the stricter client requirement of no intermetal...

Open

11794

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

11795

4.4.3

AI

No

add date

Microstructure examination is performed as per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at minimum 400X magnification. Acceptance criteria: structure is basically free from intermetallic precipitates (isolated pre...

Open

11796

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

11797

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

11798

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

11799

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per NORSOK MDS D51 Rev 06 (ISO 17781, G48 Method A). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

11800

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor are their roles and responsibilities defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructiv...

Open

11801

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is confirmed for the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12...

Open

11802

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed or qualified. Standard NDE methods (eddy current, ultrasonic, hydrostatic) are not fully availa...

Open

11803

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair; standard NDE acceptance criteria and practices for the specified dimension are not confirmed as feasible or aligned wit...

Open

11804

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are confirmed to be per the applicable ASTM standards (including A999), with no deviations specified by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/0...

Open

11805

7.0

AI

No

add date

ASTM A790 (6.1.3) and NORSOK MDS D51 (§13) both require finished pipes to be pickled or bright annealed, fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11806

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790, requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring traceability as specified. Source: DMV_STANDARD_BOOK/02-03-01...

Open

11807

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

11808

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

11809

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

11810

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, fulfilling the qualification requirement for the specified size and product f...

Open

11811

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

11812

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control and compliance with relevant standards. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev ...

Open

11813

10.2

AI

No

add date

No provided documentation includes explicit evidence of NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, ladle chemical analysis, solution anneali...

Open

11814

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified up to the required wall thickness. Source: DMV_STANDAR...

Open

11815

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782, and there is no evidence that QTR/MPCR documentation is available for review as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

11816

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

11817

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11818

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed by heat analysis with supplier certification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Dige...

Open

11819

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

11820

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

11821

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with frequency and method matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

11822

4.1

AI

No

add date

Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified locations and directions, are fulfilled for DMV 25.7N...

Open

11823

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370, and material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORS...

Open

11824

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

11825

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

11826

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact test requirements at -46°C, including minimum absorbed energy values and sub-size specimen reduction factors. The specified pipe dimensions allow for required transverse and longitudinal Charpy V-n...

Open

11827

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH solution after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

11828

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is required for micrographic examination as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

11829

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

11830

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

11831

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, actual magnification and scale bar reported if no intermetallic phases are detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

11832

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

11833

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10 µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully fulfilled. Source: DMV_ST...

Open

11834

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

11835

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

11836

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

11837

4.5

AI

No

add date

Applicable standards are referenced but there is no explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781. Requirement not fulfilled based on available information. Source: DMV_STANDARD_BOOK/12-03...

Open

11838

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, with compliance confirmed by destructive and micrographic tests. Source: DMV_STANDARD_BOOK...

Open

11839

4.5

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 (ISO 17781, G48 Method A) requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

11840

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

11841

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultr...

Open

11842

5.2

AI

No

add date

NDE per ASTM A790 and NORSOK M-630 MDS D51 is required, but there is no confirmation that NORSOK-specific NDE criteria are met. For the specified OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available...

Open

11843

5.2

AI

No

add date

No provided documentation confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor that the specified NDE acceptance criteria will be applied as standard for the reques...

Open

11844

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no overriding specification from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances...

Open

11845

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11846

8.0

AI

No

add date

Marking includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAND...

Open

11847

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

11848

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

11849

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

11850

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified s...

Open

11851

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to delivered products, fulfilling the requirement for documentation to be transmitted to TechnipFMC and traceable as per SIR205. Source: DMV_STANDARD_BOOK/0...

Open

11852

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference. Source: DMV_STANDARD_BO...

Open

11853

10.2

AI

No

add date

No provided document contains all required documentation and certification details, including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results...

Open

11854

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, meeting all relevant mechanical, chemical, and testing requirements for 25 Cr Duplex stainless steel seamless pipes as specified. Source: DMV...

Open

11855

1.0

AI

No

add date

No evidence of supplier qualification to NORSOK M-650/ISO 17782 for the exact product supplied or availability of QTR/MPCR documentation as required by the specification. MST-Tubes is M-650 accredited for DMV25.7N but not to ISO 17782, and other docu...

Open

11856

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

11857

3.1

AI

No

add date

AOD or equivalent is used 100% for MST-Tubes and DMV 25.7N complies with the chemical composition requirements in Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

11858

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the inquiry's wall thickness of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

11859

3.2

AI

No

add date

Manufacturing process is qualified to NORSOK M-650, heat treatment is solution annealing followed by accelerated cooling (water quenching) per ASTM A790, and furnaces comply with NORSOK M-650/ISO 17782. Pipes are arranged to ensure free circulation o...

Open

11860

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

11861

4.1

AI

No

add date

Tensile and hardness tests are mentioned, but there is no confirmation that impact, corrosion, and microstructure examinations are performed per heat and heat treatment lot as required by ASTM A790. No source confirms all required tests per lot are p...

Open

11862

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

11863

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no information on CVN impact testing, test directions for CVN, or detailed sampling locations for all required tests (CVN, corrosion, microstructure, hardness) as specified in Table 3 of the cl...

Open

11864

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature with criteria matching or exceeding Table 4 (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%), and referenced standards require testing in accordance with ASTM A370 or ISO 6892-1 for DMV 25.7N. Source: ...

Open

11865

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required by the specification are not explicitly confirmed or are not met in the referenced documents. ASTM A790 digest does not state the required values, and the NO...

Open

11866

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, meeting the minimum wall thickness requirements for both standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testi...

Open

11867

4.3

AI

No

add date

Pipe dimensions allow for both longitudinal and transverse Charpy V-notch impact specimens, and impact testing at -46°C with the specified absorbed energy values is feasible and can be fulfilled for this product. Source: DMV_STANDARD_BOOK/12-03-02 - ...

Open

11868

4.4.1

AI

No

add date

No information confirming metallographic preparation and examination of 25 Cr Duplex stainless steels per ISO 17781 or the specified etchant solution; grain size examination procedures provided are not applicable to duplex grades. Source: DMV_STANDAR...

Open

11869

4.4.1

AI

No

add date

No information confirming the use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination is provided. Requirement not addressed for ferrite balance and intermetallic phase examination in d...

Open

11870

4.4.2

AI

No

add date

The microstructure must be basically free from intermetallic precipitates, with isolated precipitates allowed if not distributed throughout the specimen and each phase is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - S...

Open

11871

4.4.2

AI

No

add date

No evidence of noting or recording the presence and location of intermetallic phases with micrographs at 400x magnification is provided or addressed in the relevant documents. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing...

Open

11872

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness if intermetallic pha...

Open

11873

4.4.2

AI

No

add date

No relevant documentation addresses the requirement to report centerline intermetallic stringers or base acceptance on CVN and corrosion test results if such stringers are present. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I....

Open

11874

4.4.2

AI

No

add date

NORSOK MDS D41 Rev 06 and NORSOK MDS D51 Rev 06 allow isolated intermetallic precipitates below 10µm, which does not meet the client’s stricter requirement of zero tolerance for intermetallic phases/precipitates if CVN testing cannot be completed. No...

Open

11875

4.4.3

AI

No

add date

No acceptance criteria or results for micrographic examination are provided or applicable for DMV 25.7N (super-duplex stainless steel); grain size examination is not required for this material type and is not addressed in the referenced documents. So...

Open

11876

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11877

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are provided; only a heading is present without details, making validation impossible. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSO...

Open

11878

4.5

AI

No

add date

Specification requires pitting corrosion test per ISO 17781, G48 Method A at 25°C for 24 hours, with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the client's requirements exactly. Source: DMV_ST...

Open

11879

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDA...

Open

11880

5.2

AI

No

add date

No confirmation of 100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 or ISO 10893-10, nor mention of reference notches as per Figure 3 of ASTM E213 or required testing sequence after all processing steps. Dimensional limit...

Open

11881

5.2

AI

No

add date

100% qualitative anti-mixing PMI check is performed on standard production at Montbard using appropriate instruments, fulfilling general NDE acceptance criteria for PMI. Source: DMV_STANDARD_BOOK/12-06-06 - Positive Material Identification (PMI) in M...

Open

11882

5.2

AI

No

add date

No relevant document explicitly states that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair; acceptance/rejection criteria for NDE indications are not detailed for the specified pro...

Open

11883

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for the requested product are confirmed as per the applicable ASTM standards (including ASTM A 790 with A 999 for tolerances), with no overriding TechnipFMC part report or drawing indicated. Requirement ...

Open

11884

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and white pickled or bright annealed per NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790 diges...

Open

11885

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

11886

10.0

AI

No

add date

No evidence of an ISO 9001 quality-assurance system or certification by a competent EEA body is provided for the material manufacturer or Montbard plant. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

11887

10.1

AI

No

add date

No evidence that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body is provided. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-03 - Cer...

Open

11888

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11889

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, demonstrating qualification for the size and product for...

Open

11890

10.2

AI

No

add date

No evidence that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC is provided. Inspection and certification documents are described, but explicit compliance with the transmission and traceability requir...

Open

11891

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control for mill inspection, which fulfills the requirement. Standard practice implies inclusion of information required by ASTM A790 and NORSOK M-630. Source: D...

Open

11892

10.2

AI

No

add date

No provided documentation includes NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or results of required metallurgical and non-destructive testing for the specific ...

Open

11893

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all relevant mechanical, chemical, and testing requirements, and are M-650 qualified up to the required wall thickness. Source: Engineering Data Ta...

Open

11894

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782 as required; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11895

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, fulfilling the requirement for manufacturer and process qualification and compliance with ...

Open

11896

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11897

3.1

AI

No

add date

DMV 25.7N (UNS S32760) chemical composition matches the requirements of Table 2 and complies with ASTM A790 and NORSOK MDS D51 Rev 06, including PREN ≥ 40 and all specified element limits. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, ...

Open

11898

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

11899

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, with test frequency specified as 1/lot and lot definition referenced from ASTM A790 §9.1. S...

Open

11900

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, directly referencing the required table for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

11901

4.5

AI

No

add date

No explicit confirmation that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 will be performed; ASTM G48 and ISO 17781 are not mentioned in the referenced documents. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion te...

Open

11902

4.1

AI

No

add date

Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, are fulfille...

Open

11903

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the specified tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produc...

Open

11904

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW, fulfilling all specified mechanical requirements. Source: DMV_STANDARD_BOOK/02-04-03 - D...

Open

11905

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfills the requirement as the pipe wall thickness exceeds the minimum required for testing per ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Imp...

Open

11906

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -466C, with minimum absorbed energy values for both transverse and longitudinal specimens, and the specified pipe dimensions allow for both test orientations as required. Source: D...

Open

11907

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

11908

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

11909

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

11910

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

11911

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

11912

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, as specified in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

11913

4.4.2

AI

No

add date

No document specifies a zero-tolerance policy for intermetallic phases and/or precipitates if CVN testing cannot be completed; isolated precipitates are allowed under some specifications, which does not meet the requirement for total prohibition in t...

Open

11914

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

11915

4.4.3

AI

No

add date

Micrographic examination per ISO 17781 is specified, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requirement for m...

Open

11916

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 (ASTM A790, NORSOK M-650/ISO 17782) are fully met, including compliance for destructive and microstructural tests, manufacturing, heat treatment, and qualification procedures. ...

Open

11917

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11918

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

11919

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects is performed in accordance with ASTM E213 or ISO 10893-10 for the required pipe dimensions. Acceptance of ASTM E213 implies compliance with calibration notch requirements and testing after all processi...

Open

11920

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed. Standard NDE methods (hydrostatic, ultrasonic, eddy current) for the requested pipe size are either not feasible, only available at extra cost, or re...

Open

11921

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, and NDE feasibility for the requested size is not confirmed for Montbard plant. Sou...

Open

11922

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and ASTM A999 as required, with no overriding TechnipFMC specification indicated for the inquiry. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to...

Open

11923

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11924

8.0

AI

No

add date

Marking per ASTM A790 and plant marking methods ensure mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

11925

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

11926

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA and specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

11927

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

11928

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified ...

Open

11929

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produc...

Open

11930

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and meets the requirements of ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

11931

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference. Certifica...

Open

11932

10.2

AI

No

add date

Most required documentation and certification details (NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and actual metallurgical and NDT results) a...

Open

11933

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and are M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BO...

Open

11934

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; full qualification per both NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR is not confirmed. Source: DMV_STANDARD_BOOK...

Open

11935

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

11936

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical analysis conforms to the specified table for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11937

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements. Heat analysis is performed per heat as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 ...

Open

11938

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is qualified to NORSOK M-650/ISO 17782, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by complian...

Open

11939

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

11940

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

11941

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified th...

Open

11942

4.2

AI

No

add date

Tensile testing is performed at room temperature per §7, meeting Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%, and hardness testing is performed per ASTM A790. Testing per ASTM A370 or ISO 6892-1 is referenced and compliance with NORSOK MDS D51 is confirme...

Open

11943

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

11944

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11945

4.3

AI

No

add date

DMV 25.7N meets NORSOK MDS D51 Rev 6 impact test requirements: Charpy V-notch at -46°C, minimum 45 J average and 35 J single (transverse), 65 J average and 50 J single (longitudinal if transverse not possible), with reduction factors for sub-size spe...

Open

11946

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with etching for intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

11947

4.4.1

AI

No

add date

Etching with 20–40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BOOK/0...

Open

11948

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

11949

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

11950

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included at actual magnification and a scale bar, fulfilling the requirement for representative micrographs at or near mid-wall thickness. Source: DMV_STANDARD_BOOK...

Open

11951

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

11952

4.4.2

AI

No

add date

No evidence that intermetallic phases and/or precipitates are completely prohibited when CVN testing cannot be completed; existing specifications allow isolated precipitates below 10µm, which does not meet the stricter client requirement of zero tole...

Open

11953

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

11954

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

11955

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or confirmed in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

11956

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO ...

Open

11957

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

11958

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

11959

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

11960

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not fully addressed; only ASTM A790/ASTM A999 NDE is confirmed. For the specified OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/ultrasonic tests ar...

Open

11961

5.2

AI

No

add date

No provided document explicitly states that any indication greater than the calibration notch is a defect requiring rejection or repair, nor confirms standard NDE for the specified pipe dimension at Montbard is feasible to meet this requirement. NDE ...

Open

11962

6.0

AI

No

add date

Dimensional tolerances are specified as per the applicable ASTM standard (ASTM A790/A999) for the requested product, with no deviations stated in the customer specification or part report/drawing. Source: DMV_STANDARD_BOOK/07-01 - General information...

Open

11963

7.0

AI

No

add date

ASTM A790 (6.1.3) and NORSOK MDS D51 (§13) both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

11964

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790, requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat and DMV lot numbers, and certification per EN 10204 3.1 ensures traceability. Source: DMV_STANDAR...

Open

11965

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

11966

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

11967

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system certified within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

11968

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

11969

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

11970

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and will include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 -...

Open

11971

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of metallurgical and non-de...

Open

11972

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all relevant chemical, mechanical, and testing requirements, and are M-650 qualified for the required wall thickness. Source: Item ...

Open

11973

4.5

AI

No

add date

No explicit evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or referenced in the provided documentation or standards list. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard p...

Open

11974

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to 31.75 mm WT, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

11975

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

11976

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat, confirming conformity to the requireme...

Open

11977

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

11978

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

11979

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-0...

Open

11980

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790/NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, longitudinal if not possible), corrosion, and microstructure at specified thickness locations. Or...

Open

11981

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

11982

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 06 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW, as confirmed by destructive testing and compliance with ASTM A790. Source: DMV...

Open

11983

4.3

AI

No

add date

Charpy V-notch testing in accordance with ASTM A370 and ISO 148-1 is feasible for the specified pipe dimensions and can be performed as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03...

Open

11984

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C (transverse: avg 45 J, single 35 J; longitudinal: avg 65 J, single 50 J if transverse not possible). The specified pipe dimensions allow for both longitudinal and tra...

Open

11985

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

11986

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

11987

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

11988

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, Digest NORSOK ...

Open

11989

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

11990

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

11991

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

11992

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully fulfilled by the available...

Open

11993

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

11994

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corr...

Open

11995

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

11996

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

11997

4.5

AI

No

add date

DMV 25.7N complies with all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including destructive, micrographic, corrosion tests, ferrite content, heat treatment, and manufacturing process requirements. Microstructure acceptance is based...

Open

11998

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

11999

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

12000

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is confirmed for the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12...

Open

12001

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled; standard NDE methods (eddy current, hydrostatic, ultrasonic) are not feasible or only available at extra cost for the specified pipe size at M...

Open

12002

5.2

AI

No

add date

No provided document confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that such NDE acceptance criteria are standardly applied or feasible for the specified pipe dimension at Montb...

Open

12003

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a A...

Open

12004

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12005

8.0

AI

No

add date

Marking per ASTM A790 and plant marking procedures ensures mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest N...

Open

12006

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

12007

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

12008

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

12009

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size ...

Open

12010

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to the delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

12011

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications as specified. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D5...

Open

12012

10.2

AI

No

add date

EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. Other required docu...

Open

12013

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with explicit coverage of mechanical, chemical, and testing requirements for 25 Cr Duplex stainless steel s...

Open

12014

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of QTR/MPCR documentation availability as required by the specification. MST-Tubes is only M-650 accredited, not ISO 17782 accre...

Open

12015

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 and meets NORSOK MDS D51 Rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

12016

3.1

AI

No

add date

AOD or equivalent refining is used 100% for DMV 25.7N, and the chemical composition complies with Table 2 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Diges...

Open

12017

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the inquiry's wall thickness of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

12018

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed in accordance with ASTM A790, the manufacturing process is qualified to NORSOK M-650/ISO 17782, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heat...

Open

12019

4.1

AI

No

add date

Tensile and hardness tests are confirmed, but there is no evidence that impact, corrosion, and microstructure examinations are performed for each heat and heat treatment lot as required by ASTM A790. Testing frequency and lot definition are not addre...

Open

12020

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

12021

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no evidence of CVN impact testing, required test directions, or specified thickness locations as per the requirement. Microstructure and corrosion testing are also not addressed. Source: DMV_ST...

Open

12022

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

12023

4.2

AI

No

add date

Mechanical property values for DMV 25.7N (tensile strength, yield strength, elongation, hardness) are not provided or confirmed for the required grade; referenced documents do not contain the specific required values or pertain to a different materia...

Open

12024

4.3

AI

No

add date

Impact testing at -466C with specified absorbed energy values is feasible and can be fulfilled for pipe with 18.26mm wall thickness, as both ASTM and ISO rules confirm transverse specimens are possible for this size. Source: DMV_STANDARD_BOOK/12-03-...

Open

12025

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination per ISO 17781 or use of the specified etchant for 25 Cr Duplex stainless steels; available information only covers grain size measurement for austenitic materials and excludes duplex grades. S...

Open

12026

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination of ferrite balance and intermetallic phases is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - De...

Open

12027

4.4.2

AI

No

add date

The microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

12028

4.4.2

AI

No

add date

No evidence of noting and recording the presence and location of intermetallic phases with micrographs at 400x magnification is provided or addressed in the relevant documentation or procedures. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - ...

Open

12029

4.4.2

AI

No

add date

None of the provided documents confirm that, if intermetallic phases are not detected, a representative micrograph at or near mid-wall thickness is recorded and reported at 400x minimum magnification with actual magnification and a scale bar as requi...

Open

12030

4.4.2

AI

No

add date

No relevant documentation addresses the detection, reporting, or acceptance criteria for centerline intermetallic stringers, nor the requirement to base acceptance on CVN and corrosion test results in their presence. Source: DMV_STANDARD_BOOK/12-03-0...

Open

12031

10.1

AI

No

add date

No confirmation that the material manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body with specific assessment for materials as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentati...

Open

12032

4.4.2

AI

No

add date

NORSOK MDS D41 and D51 allow isolated intermetallic precipitates below 10µm and do not fully prohibit all intermetallic phases/precipitates when CVN testing cannot be completed, so the requirement is not fully fulfilled as specified by the client. Ot...

Open

12033

4.4.3

AI

No

add date

No information is provided confirming ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781; only grain size measurement is discussed or the requirement is not addressed at all. Source: DMV_STANDARD_BOOK/12 - Special ...

Open

12034

4.4.3

AI

No

add date

No acceptance criteria for micrographic examination are specified or evidenced for DMV 25.7N in the provided documents. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx, DMV_...

Open

12035

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12036

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided; only 'A790 NORSOK' is referenced, which does not confirm fulfillment of this requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tes...

Open

12037

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are provided in the referenced documents or section; only headings or general references are present without detailed requirements or limits. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

12038

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 G48 Method A at 25°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² are specified and match the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

12039

5.1

AI

No

add date

No evidence provided regarding qualification or certification of NDE personnel to ISO 9712 level II or III, or their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montba...

Open

12040

5.2

AI

No

add date

No explicit confirmation of 100% ultrasonic testing per ASTM E213 or ISO 10893-10 after all processing, nor confirmation of reference notch requirements or process sequence is provided in the available information. Source: DMV_STANDARD_BOOK/12 - Spec...

Open

12041

5.2

AI

No

add date

100% qualitative anti-mixing PMI check is performed on standard production at Montbard using appropriate instruments, fulfilling general acceptance criteria for PMI in the absence of a more specific customer specification. Source: DMV_STANDARD_BOOK/1...

Open

12042

5.2

AI

No

add date

ASTM A790 (referenced) requires NDE with calibration standards and mandates rejection or repair of pipes with indications greater than the calibration notch, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

12043

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed to be per the applicable ASTM standards (including ASTM A790/A999) for the requested product dimensions, with no overriding TechnipFMC specification indicated. Source: DMV_STANDARD_BOOK/07-...

Open

12044

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and white pickled or bright annealed per NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: Digest ASTM A 7...

Open

12045

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS S01 Rev 05 for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 ....

Open

12046

10.0

AI

No

add date

No evidence of an ISO 9001 certified quality-assurance system or certification by a competent EEA body with a specific assessment for materials is provided for the manufacturer. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_...

Open

12047

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and the QTR number is included in the certificate, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MCPR for ...

Open

12048

10.2

AI

No

add date

No evidence that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC as specified in the requirement. Certification and inspection documents are listed, but compliance with the specific transmission and tr...

Open

12049

10.2

AI

No

add date

Material certificate is issued according to EN 10204 Type 3.1 and validated by Quality Control for mill inspection as required. Source: 14-03 - Certification Montbard plant.doc

Open

12050

10.2

AI

No

add date

No provided document contains the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of metallurgi...

Open

12051

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as indicated in the engineering data and confirmed by the digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/0...

Open

12052

1.0

AI

No

add date

There is no explicit confirmation that the supplier is qualified for DMV 25.7N with 18.26 mm wall thickness according to NORSOK M-650/ISO 17782, nor confirmation of the availability of QTR/MPCR for review as required by the specification. Source: DMV...

Open

12053

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

12054

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12055

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12056

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

12057

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, with test frequency specified as 1/lot and lot definition referenced from ASTM A790 §9.1. S...

Open

12058

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

12059

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes per ASTM A790 and NORSOK MDS D51 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified loc...

Open

12060

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4, in compliance with NORSOK MDS D51. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

12061

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required by NORSOK MDS D51 Rev 06 and ASTM A790 for seamless pipe mechanical properties. Source: DMV_ST...

Open

12062

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact ...

Open

12063

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C, including minimum absorbed energy values for both transverse and longitudinal Charpy V-notch tests, and the specified pipe dimensions allow for required testing dire...

Open

12064

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with etching by 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dige...

Open

12065

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

12066

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

12067

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

12068

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, actual magnification and scale bar reported, fulfilling the requirement for representative micrographs at or near mid-wall thickness if intermetallic phas...

Open

12069

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

12070

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases and/or precipitates when CVN testing cannot be completed, or they allow isolated precipitates below 10 µm, which does not meet the stricter client requirement of n...

Open

12071

4.4.3

AI

No

add date

Ferrite content is measured as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content determination per ASTM E562 or image analysis per ASTM E1245 in accordance with ISO 17781. Source: DMV_...

Open

12072

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), in compliance with NORSOK MDS D51 and ...

Open

12073

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12074

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

12075

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified per NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

12076

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

12077

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

12078

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, which are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-0...

Open

12079

5.2

AI

No

add date

NDE requirements per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not addressed; standard NDE methods (hydrostatic, ultrasonic, eddy current) are not confirmed as feasible or available for the specified OD and length; dye penetrant testi...

Open

12080

5.2

AI

No

add date

No provided document explicitly confirms that indications greater than the calibration notch are classified as defects requiring rejection or repair per the requirement; acceptance criteria are not detailed or confirmed for NDE indications relative t...

Open

12081

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no deviations or special requirements from TechnipFMC specified. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 31...

Open

12082

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12083

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and standard practice at Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_S...

Open

12084

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' (§13, §14) for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

12085

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

12086

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dige...

Open

12087

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, and the QTR number is included as per M-650 qualification, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/...

Open

12088

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to delivered products, fulfilling the requirement for documentation to be transmitted to TechnipFMC and traceable as per SIR205. Source: DMV_STANDARD_BOOK/0...

Open

12089

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

12090

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control and reference to relevant standards for documentation content. Source: DMV_STANDARD_BOOK/02-04-03 - Dig...

Open

12091

10.2

AI

No

add date

Documentation confirms that EN 10204 type 3.1 certificates will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific st...

Open

12092

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification digest and customer specification listing 'A790 NORSOK'. M-650 qualification is also met for the required wall thickness. S...

Open

12093

1.0

AI

No

add date

Supplier is NORSOK M-650 accredited for UNS S32760 / DMV25.7N but not accredited to ISO 17782 as required; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12094

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

12095

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12096

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis is performed per heat and matches the required limits for all elements listed in the requ...

Open

12097

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

12098

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

12099

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with frequency and method matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

12100

4.1

AI

No

add date

Test sampling requirements for seamless pipes per NORSOK MDS D51/ASTM A790—including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if necessary), and corrosion/microstructure at specified thickness locations—are fulf...

Open

12101

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

12102

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

12103

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

12104

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 with 8 mm striker radius is feasible for wall thickness 18.26 mm and OD 219.1 mm, meeting the requirement for the specified product. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 -...

Open

12105

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for required testing directions and specimen sizes. ...

Open

12106

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with specified etchants and procedures matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

12107

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect intermetallic phases, in accordance with ISO 17781, is explicitly required for micrographic examination, fulfilling the requirement for suitable etchant(s) as listed in ISO 17781 Appendix B to show ferrite b...

Open

12108

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

12109

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

12110

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report at actual magnification and with a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

12111

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

12112

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10 µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fulfilled by the available...

Open

12113

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

12114

4.4.3

AI

No

add date

Microstructure examination is performed as per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at minimum 400X magnification; structure must be basically free from intermetallic precipitates, with isolated precipitates a...

Open

12115

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

12116

4.5

AI

No

add date

ASTM G48 Method 'A' corrosion testing at 50°C for 24h in accordance with ISO 17781 is not explicitly mentioned or confirmed; compliance cannot be validated based on the available information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Mon...

Open

12117

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements, with M-650 qualification up to the specified wall thickness. Source: DMV_STANDARD_BOOK/02...

Open

12118

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N, with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/0...

Open

12119

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not validated; only ASTM A790/ASTM A999 NDE is confirmed. For the specified OD (219.1 mm), eddy current and ultrasonic testing at Montbard are only available at ext...

Open

12120

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair during NDE for the specified product and size; NDE feasibility for the required dimension is also not...

Open

12121

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) unless otherwise specified, with no overriding TechnipFMC specification indicated for the requested size and grade. Source: DMV_STANDARD_BOOK/07-01 - General information.doc...

Open

12122

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and white pickled or bright annealed according to NORSOK MDS D51 Rev 06, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source:...

Open

12123

8.0

AI

No

add date

Marking includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAND...

Open

12124

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

12125

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body established within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

12126

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

12127

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling supplier qualification documentation requirem...

Open

12128

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to delivered products, fulfilling SIR205 documentation requirements for TechnipFMC. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

12129

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

12130

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, steel melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destruct...

Open

12131

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the item table and confirmed by the referenced specification digest. Source: Item Table, Digest NORSOK MDS D51 Rev 06.docx

Open

12132

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of full qualification to both NORSOK M-650/ISO 17782 or availability of QTR/MPCR is provided as required by the specification. So...

Open

12133

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

12134

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12135

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the requirement table and is confirmed to conform to ASTM A790 with supplier certification and heat analysis per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

12136

3.2

AI

No

add date

Heat treatment is solution annealing followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

12137

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

12138

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

12139

4.1

AI

No

add date

Test sampling requirements for seamless pipes per ASTM A790 and NORSOK MDS D51 Rev 6, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure at specified locations, ar...

Open

12140

4.2

AI

No

add date

Tensile and hardness testing are performed in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

12141

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

12142

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, with both longitudinal and transverse specimens possible as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive tes...

Open

12143

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible), with reducti...

Open

12144

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with specified etchants for intermetallic phases and ferrite balance after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

12145

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is specified and fulfills the requirement for suitable etchants as listed in ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

12146

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12147

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

12148

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

12149

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, actual magnification and scale bar reported, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

12150

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results as specified in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

12151

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is...

Open

12152

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

12153

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Acceptance: structure must be basically free from intermetallic precipitates; isolated precipitates allo...

Open

12154

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as specified in NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 R...

Open

12155

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation or data sources relevant to the requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion test...

Open

12156

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 (ASTM A790, NORSOK M-630, M-650/ISO 17782) are fully addressed and DMV 25.7N is compliant for all relevant destructive and microstructural tests (tensile, impact, corrosion, mi...

Open

12157

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

12158

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 or equivalent, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in ...

Open

12159

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed on the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - U...

Open

12160

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed. Standard NDE methods (eddy current, hydrostatic, ultrasonic) for OD 219.1 mm are either not feasible or only available at extra cost and require tech...

Open

12161

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are considered defects requiring rejection or repair; NDE acceptance criteria per the requirement are not stated or confirmed for the specified product and size. NDT feasibi...

Open

12162

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) unless otherwise specified, with no evidence of overriding requirements from TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-0...

Open

12163

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12164

8.0

AI

No

add date

Marking is performed per ASTM A790 §14 and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

12165

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12166

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

12167

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

12168

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size ...

Open

12169

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with all required traceable documentation, fulfilling the requirement for documentation traceable to the products being delivered (SIR205). Source: DMV_STANDARD_BOOK/02 - Spe...

Open

12170

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification ...

Open

12171

10.2

AI

No

add date

No provided documentation includes all required details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis (ladle), solution annealing parameters, or complete metallurgic...

Open

12172

1.0

AI

No

add date

DMV 25.7N seamless pipe is specified, with compliance to ASTM A790 and NORSOK M-630 MDS D51 rev. 6 confirmed, including M-650 qualification and all relevant requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

12173

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06...

Open

12174

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to M-650 or ISO 17782, with qualification testing per NORSOK M-630 MDS D51 rev. 6. Source: DMV_STANDARD_BOOK/02...

Open

12175

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12176

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition requirements, including PRE ≥ 40, as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

12177

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

12178

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with lot defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

12179

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

12180

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified th...

Open

12181

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

12182

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

12183

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfills the requirement as the pipe wall thickness exceeds the minimum required for testing per ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Imp...

Open

12184

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; the specified pipe dimensions allow for transverse Charpy V-notch...

Open

12185

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants and electrolytic etching after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02...

Open

12186

4.4.1

AI

No

add date

Etching with 20–40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

12187

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

12188

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

12189

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

12190

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases, including stringers, with acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

12191

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

12192

4.4.3

AI

No

add date

Ferrite content is determined per ASTM E 562 or ASTM E 1245, performed in accordance with ISO 17781, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORS...

Open

12193

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

12194

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS ...

Open

12195

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is fulfilled or mentioned in the provided documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

12196

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including destructive, micrographic, corrosion tests, ferrite content, heat treatment, and manufacturing process requirements. Source: DMV_STANDARD_BOOK/02...

Open

12197

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A at 50°C for 24 hours, meeting the acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m² as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

12198

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montb...

Open

12199

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

12200

5.2

AI

No

add date

NDE per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 is not confirmed; only ASTM A790/A999 NDE is detailed. For OD 219.1 mm, standard NDE methods (eddy current, hydrostatic, ultrasonic) are not fully feasible or require extra cost and technical ap...

Open

12201

5.2

AI

No

add date

The specific NDE acceptance criterion that any indication greater than that produced by the calibration notch represents a defect, requiring rejection or repair, is not explicitly stated or guaranteed in the referenced documents. Standard NDE methods...

Open

12202

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 for seamless pipe under ASTM A790) unless otherwise specified, with no evidence of a deviation or special tolerance request from TechnipFMC. Source: DMV_STANDARD_BOOK/07.01 - Gene...

Open

12203

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12204

8.0

AI

No

add date

Marking includes heat number and DMV lot number using indelible ink and vibro-etching, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

12205

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 ...

Open

12206

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

12207

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

12208

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, and the QTR number is included as per M-650 qualification, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/M...

Open

12209

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

12210

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant specifications and manufacturing details as required by the client specification. So...

Open

12211

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, heat number, chemical analysis, solution annealing parameters, and actual metallurgical and NDT test results are not pr...

Open

12212

1.0

AI

No

add date

DMV 25.7N seamless pipes are 25 Cr Duplex stainless steel, manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, meeting all material, manufacturing, testing, and documentation requirements. Source: DMV_STANDARD_BOOK/02-03-0...

Open

12213

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782, as required. No confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12214

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

12215

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PRE ≥ 40, matching the requirements of Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat as required. Source: 02-03-01...

Open

12216

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling (including water quenching per ASTM A790), furnaces are qualified to NORSOK M-650/ISO 17782, and pipes are arranged to ensure free circulation of heating and cooling media during heat treatm...

Open

12217

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined by ASTM A790, with test frequency specified as 1/lot and explicit reference to ASTM A790 §9.1 for lot def...

Open

12218

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

12219

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and meets the requirements of ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

12220

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, in accordance with ASTM A790 an...

Open

12221

4.2

AI

No

add date

Tensile and hardness testing are performed in accordance with ASTM A370 or ISO 6892-1, and the material meets the specified tensile and maximum hardness properties of Table 4 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

12222

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

12223

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfills the requirement as the pipe wall thickness exceeds the minimum required for testing per ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Imp...

Open

12224

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energy values for transverse and longitudinal specimens, and the specified pipe dimensions allow for required transverse Charpy V-notch testing...

Open

12225

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH solution after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

12226

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

12227

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

12228

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

12229

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with representative micrographs at or near mid-wall thickness, actual magnification, and a scale bar included if intermetallic phases are not detected. Source: DMV_STANDARD_BOO...

Open

12230

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

12231

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10 µm if not distributed over the whole specimen, which does not meet the stricter requirement that intermetallic phases and/or precipitates are not permitted at all when C...

Open

12232

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard alignment. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

12233

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781 with specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requirement f...

Open

12234

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

12235

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

12236

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

12237

4.5

AI

No

add date

DMV 25.7N meets the pitting corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours, with no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

12238

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source: DM...

Open

12239

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

12240

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. Standard NDE methods (EC/UT/hydrostatic) are only partially feasible for the requested OD and length, with eddy current not feasible and h...

Open

12241

5.2

AI

No

add date

No explicit confirmation that NDE acceptance criterion based on calibration notch is applied; NDE with calibration notch reference is not standard or feasible for the requested dimension at Montbard; requirement not fulfilled for the specified produc...

Open

12242

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) as required, with no overriding specification indicated by the customer or TechnipFMC part report or drawing. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_...

Open

12243

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12244

8.0

AI

No

add date

Marking is performed per ASTM A790 §14 and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

12245

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

12246

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

12247

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

12248

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification de...

Open

12249

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to delivered products, fulfilling the documentation and traceability requirement for TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

12250

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

12251

10.2

AI

No

add date

EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. Other required docu...

Open

12252

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03...

Open

12253

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782, as explicitly required. No evidence provided for availability of Qualification Test Record/Manufacturer Procedure Conformity Records (QTR/MPC...

Open

12254

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

12255

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; DMV 25.7N complies with the specified chemical composition per Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06...

Open

12256

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN ≥ 40 as required by Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 06 standards. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 R...

Open

12257

3.2

AI

No

add date

Pipes are solution annealed followed by water quenching per ASTM A790, furnaces and process are qualified to NORSOK M-650, and procedures ensure free circulation of heating and cooling media during heat treatment including accelerated cooling. Source...

Open

12258

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion, and microstructure tests is performed per heat and heat treatment lot as defined by ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

12259

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

12260

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, in compliance with ASTM A790 an...

Open

12261

4.2

AI

No

add date

Tensile testing is performed at room temperature per NORSOK MDS D51, which refers to ASTM A790; ASTM A370 and ISO 6892-1 are referenced as acceptable methods, and the required tensile and hardness properties match those in Table 4 of NORSOK MDS D51. ...

Open

12262

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

12263

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and meets the requirements of ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

12264

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal, including reduction factors for su...

Open

12265

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

12266

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

12267

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

12268

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

12269

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

12270

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 requires reporting of intermetallic phases, with acceptance based on CVN and corrosion test results if such phases are present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STAN...

Open

12271

4.4.2

AI

No

add date

No provided document fully prohibits intermetallic phases and/or precipitates when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10μm, which does not meet the stricter client requirement of zero tolerance i...

Open

12272

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

12273

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with defined etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on imp...

Open

12274

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

12275

4.5

AI

No

add date

No explicit evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or planned. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

12276

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive, micrographic, ferrite, corrosion tests, heat treatment, and manufacturing process requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

12277

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

12278

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

12279

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

12280

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled. Standard NDE methods (hydrostatic, EC, UT) per ASTM A790 are referenced, but Montbard plant feasibility for the requested OD (219.1 mm) ...

Open

12281

5.2

AI

No

add date

No explicit confirmation that any indication greater than the calibration notch is considered a defect and that such pipe/tubing will be rejected or repaired; NDE acceptance criteria are not specified for the requirement in the referenced documents o...

Open

12282

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no deviations specified by TechnipFMC or in the customer specification or drawing. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances acco...

Open

12283

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12284

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

12285

9.0

AI

No

add date

Weld repairs are explicitly stated as not acceptable under 'Surface finish / Repairs of defects' (§13, §14), fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

12286

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

12287

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

12288

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number as required. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

12289

10.2

AI

No

add date

No evidence that documentation traceable to the delivered products will be transmitted to TechnipFMC as required by SIR205. Available documents mention certification and documentation types but do not confirm automatic transmission and traceability t...

Open

12290

10.2

AI

No

add date

Certification is provided to EN 10204 Type 3.1 and includes all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary or...

Open

12291

10.2

AI

No

add date

EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 identification, steel melting practice and refining method, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the actual steel producer na...

Open

12292

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03...

Open

12293

1.0

AI

No

add date

No evidence is provided that the supplier is qualified to both NORSOK M-650 and ISO 17782, nor is there confirmation of the availability of Qualification Test Records (QTR/MPCR) for review. The supplier is only accredited to M-650, not ISO 17782, and...

Open

12294

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, fulfilling the requirement for manufacturer and process qualification and compliance with ...

Open

12295

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12296

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as per Table 2 and NORSOK MDS D51 Rev 06. Heat analysis is performed per heat and matches the specified limits for all elements listed in the requirement...

Open

12297

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

12298

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, meeting the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

12299

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

12300

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specifi...

Open

12301

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the specified tensile and maximum hardness properties. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

12302

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

12303

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C (transverse: avg 45 J, single 35 J; longitudinal: avg 65 J, single 50 J), and the specified pipe dimensions allow for required transverse Charpy V-notch testing as per...

Open

12304

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

12305

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spe...

Open

12306

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12307

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

12308

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

12309

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

12310

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

12311

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully fulfilled. Source:...

Open

12312

4.4.3

AI

No

add date

Ferrite content is checked per ISO 17781 using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing methods and standard alignment. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

12313

4.4.3

AI

No

add date

Micrographic examination is performed as per ISO 17781 with specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance is based o...

Open

12314

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

12315

4.5

AI

No

add date

No explicit evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 will be performed or is addressed in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

12316

4.5

AI

No

add date

DMV 25.7N meets all relevant metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content. Source: DMV...

Open

12317

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

12318

5.1

AI

No

add date

No evidence is provided confirming NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non...

Open

12319

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, which are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-0...

Open

12320

5.2

AI

No

add date

NDE per ASTM A790 is available, but NORSOK M-630 MDS D51/NORSOK M-650/ISO 17782-specific NDE acceptance criteria are not confirmed. For OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic testing is only available at extra c...

Open

12321

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed by heat analysis per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790....

Open

12322

5.2

AI

No

add date

No provided documentation explicitly states that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, and eddy current testing (a standard NDE method) is not feasible for the requested ...

Open

12323

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and ASTM A999 as required, with no override specified by TechnipFMC. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to AS...

Open

12324

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12325

8.0

AI

No

add date

Marking per ASTM A790 and standard Montbard practices includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD...

Open

12326

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

12327

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

12328

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

12329

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification dem...

Open

12330

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

12331

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary or QTR n...

Open

12332

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice and refining method, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the actual steel produce...

Open

12333

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the 'Norms / Customer Specifications' and confirmed by the digest for DMV 25.7N (UNS S32760), including all mechanical, chemical, and testing r...

Open

12334

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR documentation availability. Requirement for qualification to both NORSOK M-650/ISO 17782 and documentation availability i...

Open

12335

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to M-650 or ISO 17782, meeting the qualification testing requirements of NORSOK M-630 MDS D51 rev. 6. Source: D...

Open

12336

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev...

Open

12337

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

12338

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, with test frequency specified as 1/lot for each test type. Source: DMV_STANDARD_BOOK/02 - S...

Open

12339

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

12340

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure, with specified locations and directions, is fulfilled for DMV 25.7N pipes. For...

Open

12341

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 as required, and material meets the specified tensile and maximum hardness properties. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

12342

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

12343

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfilled for the specified pipe dimensions according to ASTM A370 and ISO 148-1 requirements for minimum wall thickness. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Imp...

Open

12344

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C: minimum transverse (average 45 J, single 35 J) and longitudinal (average 65 J, single 50 J) absorbed energy, with applicable reduction factors for sub-size specimens...

Open

12345

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified electrolytic etchant after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

12346

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

12347

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

12348

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STANDA...

Open

12349

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

12350

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

12351

4.4.2

AI

No

add date

The referenced documents do not fully prohibit intermetallic phases and/or precipitates if CVN testing cannot be completed; isolated precipitates below 10µm are allowed, which does not meet the stricter client requirement of no intermetallics or prec...

Open

12352

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

12353

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and ...

Open

12354

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

12355

4.5

AI

No

add date

No explicit evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

12356

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

12357

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

12358

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor are their roles and responsibilities as defined in ISO 9712 addressed. Source: DMV_STANDARD_BOOK/12-02-01 - Non d...

Open

12359

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

12360

5.2

AI

No

add date

NDE requirements per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not demonstrated as fulfilled. Standard NDE methods (eddy current, hydrostatic, ultrasonic) are not available for the requested OD at Montbard without extra cost or specia...

Open

12361

5.2

AI

No

add date

No provided documentation explicitly states that any indication greater than the calibration notch is considered a defect requiring rejection or repair, and standard NDE methods for this requirement are not feasible or only available at extra cost fo...

Open

12362

6.0

AI

No

add date

Dimensional tolerances for the specified pipe are per applicable ASTM standards (A790 referencing A999), with no overriding tolerances specified by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - To...

Open

12363

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12364

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

12365

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

12366

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

12367

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

12368

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling supplier qualification documentation requirem...

Open

12369

10.2

AI

No

add date

Certification includes EN 10204 type 3.1 with full traceability and ISO 9001 certification, fulfilling the requirement for documentation to be transmitted and traceable to the products. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

12370

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 ...

Open

12371

10.2

AI

No

add date

EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. No evidence of actu...

Open

12372

1.0

AI

No

add date

DMV 25.7N seamless pipes are 25 Cr Duplex stainless steel and are fully compliant with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, as specified in the client inquiry and confirmed by technical digests. Source: DMV_STA...

Open

12373

1.0

AI

No

add date

No evidence is provided that the supplier is qualified to both NORSOK M-650 and ISO 17782, nor is there confirmation of the availability of Qualification Test Records/Manufacturer Procedure Conformity Records for review. Supplier is only accredited t...

Open

12374

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

12375

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12376

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PREN ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12377

3.2

AI

No

add date

Heat treatment is solution annealing followed by accelerated cooling (water quenching) per ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650/ISO 17782. Pipes are placed to ensure free circulation of heating and cooling medi...

Open

12378

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

12379

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for sampling requirements, fulfilling the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

12380

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

12381

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if transverse not possible), corrosion, and microstructure tests at specified thickness locations, in compliance with...

Open

12382

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and the material meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dige...

Open

12383

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

12384

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, meeting the requirement. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

12385

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for required testing orientation and specim...

Open

12386

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

12387

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

12388

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

12389

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are reported with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

12390

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

12391

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK/0...

Open

12392

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

12393

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

12394

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

12395

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12396

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as specified in NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO...

Open

12397

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

12398

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor reference to roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing ...

Open

12399

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

12400

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no explicit confirmation of compliance with the additional NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782 NDE requirements. For the requested OD (219.1 mm), eddy current testing is only feasible with multi...

Open

12401

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair; NDE feasibility for the specified OD is also not confirmed for the required criteri...

Open

12402

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790) for the requested pipe dimensions, with no evidence of override by TechnipFMC part report or drawing. Source: DMV_STANDARD_BOOK/07-01 - General informa...

Open

12403

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12404

8.0

AI

No

add date

Marking is performed per ASTM A790 §14, ensuring full traceability to melt and heat treatment lot, using methods that include heat number and DMV lot number as standard practice at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSO...

Open

12405

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

12406

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

12407

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

12408

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling supplier qualification documentation requirem...

Open

12409

10.2

AI

No

add date

No provided document explicitly confirms that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205; only general certification and documentation practices are mentioned without specific reference to SIR205 o...

Open

12410

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

12411

10.2

AI

No

add date

EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. No specific documen...

Open

12412

1.0

AI

No

add date

DMV 25.7N seamless pipes are 25 Cr Duplex stainless steel, fully compliant with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, including chemical, mechanical, manufacturing, and testing requirements. M-650 qualification ...

Open

12413

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782, and there is no confirmation of QTR/MPCR availability as required. Requirement is not fully fulfilled for NORSOK M-650/ISO 17782 qualificatio...

Open

12414

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

12415

3.1

AI

No

add date

AOD or equivalent refining is standard and required for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12416

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN requirements as per Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 6 requirements. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_B...

Open

12417

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is qualified to NORSOK M-650/ISO 17782, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by complian...

Open

12418

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

12419

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling as outlined in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

12420

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at the spe...

Open

12421

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4 as specified in NORSOK MDS D51. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

12422

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 06 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

12423

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 and ISO 148-1 is feasible for the specified pipe dimensions, as the wall thickness exceeds the minimum required for testing. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

12424

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for both transverse and longitudinal testin...

Open

12425

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

12426

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is explicitly required for micrographic examination, fulfilling the requirement for suitable etchants as listed in ISO 17781 Appendix B...

Open

12427

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

12428

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

12429

4.4.2

AI

No

add date

Micrographs at a minimum magnification of 400x are taken at or near mid-wall thickness, with actual magnification and scale bar, if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

12430

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

12431

4.4.2

AI

No

add date

No provided document fully prohibits intermetallic phases and/or precipitates when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10μm, which does not meet the zero-tolerance requirement in this scenario. So...

Open

12432

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

12433

4.4.3

AI

No

add date

Micrographic examination is performed as per ISO 17781 with specified etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, and reporting of carbides/nitrides. Acceptance is base...

Open

12434

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% and DMV 25.7N complies with this requirement according to ISO 17781 and ASTM E1245. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

12435

4.5

AI

No

add date

No direct evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or planned for the requirement. Only general standards are referenced without explicit confirmation of the specific test or method...

Open

12436

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including chemical composition, PRE, tensile, impact, corrosion, microstructure, and ferrite content requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

12437

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02...

Open

12438

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard and required for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

12439

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

12440

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 can be performed after all processing, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destru...

Open

12441

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no explicit confirmation of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782 NDE requirements. Standard NDE (EC, UT, hydrostatic) is not available for the requested OD at Montbard witho...

Open

12442

5.2

AI

No

add date

No provided documentation explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor that such NDE acceptance criteria are standardly performed or feasible for the specified pi...

Open

12443

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the specified pipe size, with no evidence of deviation or override in the customer specification or part report/drawing. Source: DMV_STANDARD_BOOK/07.01 - General inform...

Open

12444

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12445

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and standard practice at Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_S...

Open

12446

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

12447

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

12448

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

12449

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified s...

Open

12450

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

12451

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

12452

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C: minimum transverse 45/35 J and longitudinal 65/50 J for thickness >6mm. The specified pipe dimensions allow for required impact testing directions and specimen sizes....

Open

12453

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of full qualification to both standards or availability of QTR/MPCR documentation for review as required by the specification. So...

Open

12454

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all metallurgical and no...

Open

12455

1.0

AI

No

add date

DMV 25.7N seamless pipes are confirmed as 25 Cr Duplex stainless steel, fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements. Manufacturing is M-650 qualified for the required wa...

Open

12456

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

12457

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12458

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits and PREN requirements specified in Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 6 requirements for S32760. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK ...

Open

12459

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification will state heat treatment condition as per ASTM A790. Pipes are processed to ensure ...

Open

12460

4.1

AI

No

add date

Tensile, hardness, impact (Charpy), corrosion, and microstructure examinations are performed at a frequency of 1 per lot, with 'lot' defined per ASTM A790, fulfilling the requirement for one set of these tests per heat and heat treatment lot as defin...

Open

12461

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

12462

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specifi...

Open

12463

4.2

AI

No

add date

Tensile testing is performed at room temperature per required standards, and DMV 25.7N meets the specified tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

12464

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets the minimum requirements: yield strength ≥ 550 MPa, tensile strength ≥ 750 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC), as specified in NORSOK MDS D51 Rev 06 and ASTM A790 for S32760. Source: DMV_STANDARD_BOOK/...

Open

12465

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370/ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness required by the standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Imp...

Open

12466

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12467

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with 20-40% NaOH or KOH solution after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

12468

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

12469

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement for distribution and size of intermetallic phases. So...

Open

12470

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

12471

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

12472

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

12473

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Full prohibition is not confirmed by the available do...

Open

12474

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781...

Open

12475

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and ...

Open

12476

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

12477

4.5

AI

No

add date

Applicable standards are listed but there is no explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781; requirement not fulfilled based on available information. Source: DMV_STANDARD_BOOK/12-03-01-...

Open

12478

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including destructive, micrographic, ferrite, corrosion tests, heat treatment, and manufacturing process requirements. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

12479

4.5

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06, which requires no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781, G48 Method A at 50°C for 24 hours. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

12480

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destru...

Open

12481

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/1...

Open

12482

5.2

AI

No

add date

NDE per ASTM A790 (hydrostatic, EC, or UT) is confirmed, but compliance with additional NDE acceptance criteria of NORSOK M-630 MDS D51 or M-650/ISO 17782 is not demonstrated. For OD 219.1 mm at Montbard, eddy current is not feasible, and hydrostatic...

Open

12483

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair; NDE acceptance criteria and feasibility for the specified dimension are not demonstrated for this requirement at Montba...

Open

12484

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding TechnipFMC specification referenced. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A 376-...

Open

12485

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12486

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

12487

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

12488

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

12489

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dige...

Open

12490

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling supplier qualification documentation requirem...

Open

12491

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03...

Open

12492

10.2

AI

No

add date

Certification is provided to EN 10204 Type 3.1 and includes all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control and compliance with specified standards. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51...

Open

12493

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of required metallurgical and non-destructive testing for the specific orde...

Open

12494

1.0

AI

No

add date

DMV 25.7N seamless pipes are 25 Cr Duplex stainless steel, manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with M-650 qualification up to the required wall thickness. Source: Requested...

Open

12495

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

12496

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

12497

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12498

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PRE ≥ 40, matching the requirements of Table 2 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12499

3.2

AI

No

add date

Heat treatment is solution annealing followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650/ISO 17782, and proper pipe arrangement during heat treatment is ensured....

Open

12500

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, with test frequency '1/lot'. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

12501

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

12502

4.1

AI

No

add date

Test sampling for seamless pipes per ASTM A790 and NORSOK MDS D51, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure tests at specified locations, is fulfilled f...

Open

12503

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with material meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

12504

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

12505

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible and fulfilled for the specified pipe dimensions (OD 219.1mm, WT 18.26mm), as wall thickness exceeds the minimum required for testing in both longitudinal and transverse direct...

Open

12506

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C, with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal. The specified pipe dimensions allow ...

Open

12507

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

12508

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

12509

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

12510

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

12511

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

12512

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included at or near mid-wall thickness, showing actual magnification and a scale bar. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

12513

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 requires reporting of intermetallic phases, and acceptance is based on CVN and corrosion test results if such phases are present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_ST...

Open

12514

4.4.2

AI

No

add date

No provided documentation prohibits all intermetallic phases and/or precipitates if CVN testing cannot be completed; isolated precipitates are allowed under current specifications, which does not meet the stricter client requirement. Source: DMV_STAN...

Open

12515

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

12516

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

12517

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

12518

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

12519

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 are met by DMV 25.7N, including chemical composition (PRE ≥ 40), microstructure (free from intermetallics), ferrite content (35-60%), and required destructive tests (tensile, i...

Open

12520

4.5

AI

No

add date

Corrosion test per ISO 17781 G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

12521

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

12522

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 can be performed after all processing steps, and the pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructiv...

Open

12523

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled. Provided documents only confirm NDE per ASTM A790/A999, and plant capability for required NDE methods (eddy current, ultrasonic, hydrost...

Open

12524

5.2

AI

No

add date

No provided documentation explicitly confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that such NDE acceptance criteria are standardly performed or feasible for the specified pipe ...

Open

12525

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no deviations or special tolerances specified by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01...

Open

12526

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12527

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot, and standard marking methods (indelible black ink, vibro-etching) include heat number and DMV lot number, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 ...

Open

12528

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

12529

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system certified within the EEA for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produc...

Open

12530

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

12531

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness for the specified size and product form. Source: DMV_STANDARD_BO...

Open

12532

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products being delivered as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

12533

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing the relevant standards as the basis for documentation content. Source: DMV_STANDARD_BOOK/02-04-...

Open

12534

10.2

AI

No

add date

EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. Required documentat...

Open

12535

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

12536

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

12537

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12538

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN ≥ 40, as required by ASTM A790 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat to ensure compliance with these standard...

Open

12539

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

12540

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with lot defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

12541

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing the table for test specimen sampling as outlined in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

12542

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, in compliance with ASTM A790 a...

Open

12543

4.2

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06, which requires tensile testing per ASTM A370 or ISO 6892-1 and meets the specified tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

12544

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

12545

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfills the requirement as the pipe wall thickness exceeds the minimum required for testing per ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Imp...

Open

12546

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C, minimum absorbed energies of 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal, and reduction factors...

Open

12547

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

12548

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is specified, fulfilling the requirement for suitable etchant(s) as listed in ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

12549

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

12550

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded as required. Source...

Open

12551

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with representative micrographs at or near mid-wall thickness, actual magnification, and a scale bar included if intermetallic phases are not detected. Source: DMV_STANDARD_BOO...

Open

12552

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

12553

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. The requirement is not fully fulfilled by the available in...

Open

12554

4.4.3

AI

No

add date

Micrographic examination per ISO 17781 is specified, including etching methods, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requireme...

Open

12555

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

12556

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

12557

4.5

AI

No

add date

DMV 25.7N complies with all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12558

4.5

AI

No

add date

DMV 25.7N meets 'No pitting at 20X magnification' and 'weight loss < 1.0 g/m²' per ISO 17781 (G48 Method A, 50°C, 24h). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Diges...

Open

12559

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 or equivalent, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibili...

Open

12560

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 can be performed after all processing, and the equipment supports the required pipe dimensions and standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non de...

Open

12561

5.2

AI

No

add date

NDE per NORSOK M-630 MDS D51/ASTM A790 is not fully fulfilled: only ASTM A790/A999 NDE is detailed, NORSOK-specific NDE is not confirmed; Eddy current testing is not feasible for OD 219.1 mm; hydrostatic and ultrasonic tests are only available at ext...

Open

12562

5.2

AI

No

add date

No explicit confirmation that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, and NDE with this acceptance criterion is not confirmed as standard or feasible for the requested dimension at Montb...

Open

12563

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are confirmed to be per the applicable ASTM standards (ASTM A999), with no overriding customer specification indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BO...

Open

12564

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12565

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot; standard marking methods (indelible ink, vibro-etching) include heat and lot numbers as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx,...

Open

12566

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

12567

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

12568

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, and QTR number is included as per M-650 qualification, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MCPR...

Open

12569

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to the delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

12570

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with issuance and validation by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

12571

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or required metallurgical and non-destructive test results. Only the country of origin of...

Open

12572

1.0

AI

No

add date

DMV 25.7N seamless pipes are 25 Cr Duplex stainless steel, manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, as specified. M-650 qualification is confirmed for the required wall thicknes...

Open

12573

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of full qualification to NORSOK M-650/ISO 17782 or availability of QTR/MPCR documentation for review as required by the specific...

Open

12574

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

12575

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12576

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including all specified element limits and PREN ≥ 40, as required by Table 2 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS...

Open

12577

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification will state heat treatment condition as per ASTM A790. Pipes are processed to ensure ...

Open

12578

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

12579

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

12580

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specifi...

Open

12581

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with tensile and hardness properties meeting Table 4 requirements for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spec...

Open

12582

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all relevant chemical, mechanical, manufacturing, and testing requirements. M-650 qualification is confirmed for the required wall thickness. Sourc...

Open

12583

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's Table 4 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

12584

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

12585

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C, minimum absorbed energies of 45/35 J (transverse) and 65/50 J (longitudinal) for thickness >6mm. The requested pipe's wall thickness (18.26 mm...

Open

12586

4.4.1

AI

No

add date

Micrographic examination and ferrite check are performed as per ISO 17781 for DMV 25.7N, including etching procedures (NaOH/KOH for intermetallics, oxalic acid for nitrides/carbides) after final polishing, fulfilling the requirement for metallographi...

Open

12587

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

12588

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

12589

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

12590

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

12591

4.4.2

AI

No

add date

Intermetallic stringers, if present, must be reported and acceptance is based on CVN and corrosion test results, as specified under micrographic examination for DMV 25.7N (NORSOK MDS D51 Rev 06). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

12592

4.4.2

AI

No

add date

No provided documentation fully prohibits intermetallic phases and/or precipitates when CVN testing cannot be completed; the referenced digest allows isolated precipitates below 10µm, which does not meet the requirement for complete prohibition in th...

Open

12593

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

12594

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Structure must be basically free from intermetallic precipitates; isolated precipitates allowed if not d...

Open

12595

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

12596

4.5

AI

No

add date

No explicit evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 will be performed or is referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

12597

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR documentation availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12598

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 06, including destructive, corrosion, micrographic, ferrite tests, heat treatment, and manufacturing process requirements. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

12599

4.5

AI

No

add date

Requirement for no pitting at 20X magnification and weight loss less than 1.0 g/m² is fulfilled per NORSOK MDS D51 Rev 06, which specifies ISO 17781 G48 Method A with these acceptance criteria for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

12600

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to level II or III in accordance with ISO 9712 or equivalent, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 ...

Open

12601

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, including reference notches as specified, and the pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - No...

Open

12602

5.2

AI

No

add date

Dye penetrant testing is offered for tube ends and bevels as 'on request' and 'not delegated,' matching the client inquiry which does not require full-length testing. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-0...

Open

12603

5.2

AI

No

add date

No provided document explicitly confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that this NDE acceptance criterion is standardly performed or feasible for the specified pipe dimen...

Open

12604

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding TechnipFMC specification indicated. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according t...

Open

12605

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12606

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-0...

Open

12607

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

12608

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

12609

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

12610

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

12611

10.2

AI

No

add date

Certification includes EN 10204 type 3.1 with full traceability and confirmation of ISO 9001 certification, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

12612

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

12613

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to 31.75 mm WT, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

12614

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice, heat number, chemical analysis, solution annealing parameters, and results of all required meta...

Open

12615

1.0

AI

No

add date

DMV 25.7N is a 25 Cr duplex stainless steel seamless pipe manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as explicitly referenced in the client inquiry and confirmed by product digests. M-650 qualification is also met...

Open

12616

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

12617

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12618

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12619

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnace compliance per NORSOK M-650/ISO 17782 qualified procedures. Certification includes heat treatment condition as per ASTM A790. Pipes are ...

Open

12620

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, and the necessary tests are feasible for the specified pipe dimensions. Source: DMV_STANDAR...

Open

12621

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

12622

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specifi...

Open

12623

4.2

AI

No

add date

Tensile testing is performed at room temperature per NORSOK MDS D51, which refers to ASTM A790. ASTM A790 requires mechanical testing per ASTM A370 or ISO 6892-1, and the material meets the specified tensile and hardness properties of Table 4. Source...

Open

12624

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: yield strength ≥ 550 MPa, tensile strength ≥ 750 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

12625

4.3

AI

No

add date

Charpy V-notch testing is feasible and the requirement is fulfilled as the pipe wall thickness exceeds the minimum required for testing according to ASTM A370 and ISO 148-1 (NPS 8: 6.35 mm ASTM, 8.74 mm ISO). Source: DMV_STANDARD_BOOK/12 - Special Te...

Open

12626

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible), with reduction factors for sub-size...

Open

12627

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12628

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with specified etchants for intermetallic phases and ferrite balance after final polishing, matching the requirement for metallographic preparation and examination in accordance with ISO 17781 a...

Open

12629

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

12630

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

12631

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

12632

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, reported at actual magnification and including a scale bar, and structure free from intermetallic precipitates. Source: DMV_STANDARD_...

Open

12633

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

12634

4.4.2

AI

No

add date

No provided documentation prohibits all intermetallic phases and/or precipitates if CVN testing cannot be completed; the closest reference allows isolated precipitates below 10μm, which does not meet the stricter client requirement. Source: DMV_STAND...

Open

12635

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

12636

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

12637

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

12638

4.5

AI

No

add date

Applicable standards listed do not mention ASTM G48 or ISO 17781, and there is no explicit confirmation that the required corrosion testing will be performed as specified. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

12639

4.5

AI

No

add date

DMV 25.7N complies with all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12640

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

12641

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

12642

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

12643

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided or addressed in the relevant documents or comments.

Open

12644

5.2

AI

No

add date

NDE per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 is required, but only ASTM A790/A999 NDE is detailed, which may not meet NORSOK requirements. For the requested OD (219.1 mm), eddy current testing is not feasible with standard equipment and is...

Open

12645

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair; NDE methods for the specified OD are not feasible or only available at extra cost at the plant. Source: 02-03-01 - Dige...

Open

12646

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the specified pipe, with no deviations or special requirements indicated by the customer specification or TechnipFMC part report/drawing. Requirement is fulfilled. Sourc...

Open

12647

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and white pickled or bright annealed per NORSOK MDS D51 Rev 06, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: Digest A...

Open

12648

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot, and standard Montbard marking methods (indelible ink, vibro-etching) include heat and lot numbers ensuring traceability. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORS...

Open

12649

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

12650

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

12651

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

12652

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size ...

Open

12653

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products being delivered as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

12654

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAN...

Open

12655

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution annealing parameters, and ...

Open

12656

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSO...

Open

12657

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

12658

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

12659

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, fulfilling the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed ...

Open

12660

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per ASTM A790 and NORSOK r...

Open

12661

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 as required for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

12662

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW as specified in Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

12663

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness required by the standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - ...

Open

12664

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energy values for transverse and longitudinal directions, and the specified pipe dimensions allow for required testing directions and specimen ...

Open

12665

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

12666

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is required for micrographic examination, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

12667

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

12668

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

12669

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

12670

4.4.2

AI

No

add date

Findings of intermetallic stringers must be reported, and acceptance is based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

12671

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed. No other relevant information addresses the requirement directly. Sour...

Open

12672

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

12673

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impa...

Open

12674

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS ...

Open

12675

4.5

AI

No

add date

No explicit evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 will be performed or is referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

12676

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, as well as manufacturing, heat treatment, and qualification requirements. Source: DMV_STAN...

Open

12677

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

12678

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712 or equivalent. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive t...

Open

12679

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/1...

Open

12680

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not addressed or confirmed as feasible for the specified pipe size. Standard NDE methods (eddy current, hydrostatic, ultrasonic) are either not feasible or only ava...

Open

12681

5.2

AI

No

add date

No provided document explicitly confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor confirms standard NDE feasibility for the requested size at Montbard. NDT methods are referenced bu...

Open

12682

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding customer specification or drawing indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a ...

Open

12683

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12684

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

12685

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

12686

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

12687

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

12688

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demonstration for th...

Open

12689

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

12690

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and will include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control confirmed for the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

12691

10.2

AI

No

add date

Most required documentation and certification details (NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and test results) are not provided. EN 10204 3.1 certificates ...

Open

12692

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 Rev 6, including chemical, mechanical, manufacturing, and testing requirements for 25 Cr Duplex stainless steel seamless pipes. Sourc...

Open

12693

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR availability as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12694

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

12695

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12696

3.1

AI

No

add date

DMV 25.7N (UNS S32760) chemical composition matches the requirement table and complies with ASTM A790 and NORSOK MDS D51 Rev 06, including PREN ≥ 40 and all specified element limits. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK...

Open

12697

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

12698

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

12699

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - De...

Open

12700

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, in compliance with ASTM A790 a...

Open

12701

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the required tensile and maximum hardness properties of Table 4 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

12702

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: minimum tensile strength 750 MPa, yield strength 550 MPa, elongation 25%, and maximum hardness 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

12703

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

12704

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal if transverse is not possible. The specified pipe dimensions allow for requ...

Open

12705

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH solution after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

12706

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

12707

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

12708

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STANDA...

Open

12709

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

12710

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

12711

4.4.2

AI

No

add date

No provided documentation explicitly prohibits all intermetallic phases and/or precipitates if CVN testing cannot be completed; the closest reference allows isolated precipitates below 10 µm, which does not meet the stricter client requirement. Sourc...

Open

12712

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

12713

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

12714

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification digest. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Diges...

Open

12715

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

12716

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 are fully addressed and DMV 25.7N is compliant for all required destructive and microstructural tests (tensile, impact, corrosion, microstructure, ferrite), with explicit compl...

Open

12717

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, meeting the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest...

Open

12718

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

12719

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, performed after all mechanical processing, meeting the requirement for 100% longitudinal defect detection and reference notch calibration...

Open

12720

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not addressed or fulfilled in the provided documents. Standard NDE methods (hydrostatic, ultrasonic, eddy current) are not fully feasible for the requested OD at Mo...

Open

12721

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor confirms feasibility of such NDE for the specified dimensions at Montbard. Sour...

Open

12722

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A999 for ASTM A790 pipe), with no overriding customer specification or drawing indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/0...

Open

12723

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12724

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790, both requiring full traceability to melt and heat treatment lot. Marking methods (indelible ink, vibro-etching) include heat and DMV lot numbers, ensuring traceability as required by the ...

Open

12725

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

12726

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

12727

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

12728

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

12729

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03...

Open

12730

10.2

AI

No

add date

Certification to EN 10204 Type 3.1 is explicitly confirmed, with inclusion of all information required by ASTM A790 and NORSOK M-630. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certification Mont...

Open

12731

10.2

AI

No

add date

No documentation is provided that includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution annealing details,...

Open

12732

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 Rev 6, including chemical, mechanical, corrosion, and testing requirements. Manufacturing is M-650 qualified up to the required wal...

Open

12733

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782, which is explicitly required. No confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12734

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

12735

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard and required, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12736

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12737

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650/ISO 17782. Pipes are treated to ensure free circulation of heating and co...

Open

12738

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

12739

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

12740

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes meets requirements for tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions per ASTM A790...

Open

12741

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-0...

Open

12742

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

12743

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

12744

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and standards; requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/1...

Open

12745

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements, including Charpy V-notch testing at -466C with minimum energy values (transverse: 45 J average/35 J single, longitudinal: 65 J average/50 J single) and reduction factors for sub-size...

Open

12746

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

12747

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is explicitly required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_...

Open

12748

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

12749

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are reported with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

12750

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

12751

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

12752

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

12753

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

12754

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance is based on im...

Open

12755

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

12756

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements, with compliance confirmed by destructive and micrographic tests and acceptance based on i...

Open

12757

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

12758

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

12759

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within the machine's capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive...

Open

12760

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not validated; standard NDE methods (hydrostatic, ultrasonic, eddy current) for the specified pipe size are either not feasible or only available at extra cost, and...

Open

12761

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair; NDE acceptance criteria and process capability for the specified size are not demon...

Open

12762

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790, which references ASTM A999 for seamless pipe, and no overriding TechnipFMC specification is indicated. Requirement is fulfilled as tolerances are per the applicable ASTM standard for the specified size and pr...

Open

12763

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12764

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

12765

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

12766

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

12767

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV25.7N, and the EN 10204 type 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

12768

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to delivered products, fulfilling the requirement for documentation to be transmitted to TechnipFMC and traceable as per SIR205. Source: DMV_STANDARD_BOOK/0...

Open

12769

10.2

AI

No

add date

Certification is provided to EN 10204 Type 3.1 and includes all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary or...

Open

12770

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and full test results—are not provided. EN 10204 3.1/3....

Open

12771

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability or full compliance with both NORSOK M-650/ISO 17782 as required by the specification. Source: DMV_STAND...

Open

12772

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

12773

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12774

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE 140, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12775

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

12776

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

12777

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/...

Open

12778

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), corrosion, and microstructure tests at specified locations and directions per NORSOK MDS D51/ASTM A7...

Open

12779

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with tensile and hardness properties meeting Table 4 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Diges...

Open

12780

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

12781

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfilled for the specified pipe dimensions according to ASTM A370 and ISO 148-1 requirements for minimum wall thickness. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Imp...

Open

12782

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements at -46°C (transverse: 45/35 J, longitudinal: 65/50 J) for thickness >6mm, and the specified pipe dimensions allow for required testing directions and specimen sizes. Source: DMV_STANDAR...

Open

12783

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with specified etchants, fulfilling the requirement for metallographic preparation and examination as per ISO 17781. Source:...

Open

12784

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

12785

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

12786

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

12787

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

12788

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 requires reporting of intermetallic stringers, with acceptance based on CVN and corrosion test results as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

12789

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

12790

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

12791

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

12792

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N according to NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev ...

Open

12793

4.5

AI

No

add date

No explicit evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 will be performed or is referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

12794

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive tests, microstructure, and ferrite content requirements for the specified wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

12795

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A @ 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/0...

Open

12796

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

12797

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

12798

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but compliance with NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 is not demonstrated. For OD 219.1 mm at Montbard, eddy current testing is not feasible, and hydrostatic/ultrasonic testing is only available at extra ...

Open

12799

5.2

AI

No

add date

No explicit statement that indications greater than the calibration notch are considered defects requiring rejection or repair; NDE method feasibility for the specified OD is limited (Eddy current not feasible, extra cost for other methods). Source: ...

Open

12800

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no evidence of override in the customer specification. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances...

Open

12801

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

12802

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

12803

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

12804

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

12805

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

12806

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

12807

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAN...

Open

12808

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, heat number, actual chemical analysis, solution annealing parameters, or results of all required metallurgical and non-destructive testing. Some doc...

Open

12809

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with explicit confirmation of compliance for mechanical, chemical, and testing requirements for the specifi...

Open

12810

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of QTR/MPCR documentation availability for review by TechnipFMC. MST-Tubes is only accredited to NORSOK M-650, not ISO 17782. Ot...

Open

12811

3.0

AI

No

add date

MST-Tubes F is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 (or ISO 17782), meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

12812

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N complies with the chemical composition requirements per Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

12813

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the required WT of 18.26 mm for this inquiry. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

12814

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782, and procedures ensure free circulation of heating and cooling media around each pip...

Open

12815

4.1

AI

No

add date

There is no evidence that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is carried out for each heat and heat treatment lot as defined in ASTM A790. Corrosion, microstructure, and impact tests are not confir...

Open

12816

4.1

AI

No

add date

No provided document includes or outlines the test specimen sampling details from Table 3; only references to Table 3 or general testing frequency are present without the required sampling information. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM...

Open

12817

4.1

AI

No

add date

Test sampling requirements for test direction (longitudinal or transverse per ASTM A790), CVN impact testing, and specific thickness locations are not fully confirmed; details on CVN, corrosion, and microstructure sampling are missing or unspecified ...

Open

12818

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature with properties meeting or exceeding Table 4, and referenced standards require testing in accordance with ASTM A370 or ISO 6892-1. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

12819

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required for DMV 25.7N are not confirmed or listed in the provided documents; referenced standards either do not specify the required values or address different grad...

Open

12820

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, meeting the minimum wall thickness requirements for both standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testi...

Open

12821

4.3

AI

No

add date

Impact testing at -46°C with specified absorbed energy values is feasible and can be fulfilled for pipe with 18.26mm wall thickness, as both ASTM and ISO rules confirm transverse specimens are possible for NPS 8 at this thickness. Source: DMV_STANDAR...

Open

12822

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination per ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels. Grain size examination is only discussed for austenitic materials, not duplex steels....

Open

12823

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination of ferrite balance and intermetallic phases in the provided documentation.

Open

12824

4.4.2

AI

No

add date

The microstructure must be basically free from intermetallic precipitates, but isolated precipitates are allowed if not distributed over the whole specimen and if the dimension of each precipitate is below 10 μm, matching the requirement exactly. Sou...

Open

12825

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report at actual magnification and with a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness if int...

Open

12826

4.4.2

AI

No

add date

No relevant documents address the reporting or acceptance criteria for centerline intermetallic stringers or their evaluation based on CVN and corrosion test results in the provided information. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examina...

Open

12827

4.4.2

AI

No

add date

NORSOK MDS D41 Rev 06 and D51 Rev 06 allow isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not fully prohibit intermetallic phases/precipitates when CVN testing cannot be completed as required by ...

Open

12828

4.4.3

AI

No

add date

No evidence of ferrite content determination by ASTM E 562, ASTM E 1245, or ISO 17781 is provided in the relevant documents. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Micrographic Examination/12-03-03 - Gra...

Open

12829

4.4.3

AI

No

add date

No provided document specifies acceptance criteria or results for micrographic examination or metallurgical properties for DMV 25.7N; relevant standards and procedures are mentioned without confirming fulfillment of the requirement. Source: DMV_STAND...

Open

12830

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and confirmed for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.d...

Open

12831

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation or specifications. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

12832

4.5

AI

No

add date

No specific acceptance criteria are defined in the requirement, making validation impossible against the provided documentation. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Dig...

Open

12833

4.5

AI

No

add date

Pitting corrosion test per ISO 17781, G48 Method A at 25°C for 24 hours is required, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², matching the client's requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

12834

5.1

AI

No

add date

No provided documents contain information on the qualification or certification of NDE personnel to ISO 9712 level II or III, or their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, ...

Open

12835

5.2

AI

No

add date

No confirmation of 100% ultrasonic testing for longitudinal defects according to ASTM E213 or ISO 10893-10, nor mention of reference notches as per Figure 3 of ASTM E213 after all processing steps is provided in the available information. Source: DMV...

Open

12836

5.2

AI

No

add date

Dye penetrant testing is performed on tube ends and bevels as required, and 100% qualitative anti-mixing PMI checks are standard, fulfilling the NDE acceptance criteria for the Montbard plant. Source: DMV_STANDARD_BOOK/12-02-05 - Dye penetrant inspec...

Open

12837

5.2

AI

No

add date

No provided document confirms that indications greater than the calibration notch are considered defects requiring rejection or repair, nor is there confirmation that NDE is standard or included for the requested product and size. Acceptance criteria...

Open

12838

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for both hot and cold finished products are confirmed as per the applicable ASTM standards (A 790 with A 999, A 213 with A 1016, A 268, A 269, A 789, A 312, A 376, A 511), with no overriding TechnipFMC s...

Open

12839

7.0

AI

No

add date

Both ASTM A790 and NORSOK MDS S01 require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS S01 Rev 05 .docx

Open

12840

9.0

AI

No

add date

Weld repairs are not acceptable as per NORSOK MDS S01 Rev 05 for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

12841

10.0

AI

No

add date

No evidence of an ISO 9001 quality-assurance system or certification by a competent EEA body is provided for the Montbard plant. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Certification Montbard plant.doc

Open

12842

10.1

AI

No

add date

No evidence provided that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-03...

Open

12843

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV25.7N up to WT = 31.75 mm (requested WT is 18.26 mm), and the EN 10204 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number for the specified s...

Open

12844

10.2

AI

No

add date

No provided document confirms that documentation traceable to the products and transmitted to TechnipFMC as required by SIR205 will be provided. There is no explicit mention of SIR205, traceability, or transmission to TechnipFMC as specified in the r...

Open

12845

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control, with reference to ASTM A790 and NORSOK M-630 in the order specification, fulfilling the requirement. Source: 14-03 - Certification Montbard plant.doc

Open

12846

10.2

AI

No

add date

No provided document contains the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or test results. Only gener...

Open

12847

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, DMV_STANDARD_B...

Open

12848

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782; full qualification per NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR is not confirmed for review by TechnipFMC as required by the specification. Sourc...

Open

12849

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

12850

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12851

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN ≥ 40 as required by Table 2 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12852

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

12853

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

12854

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability or full qualification per both standards is provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12855

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, fulfilling the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed ...

Open

12856

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions, fulfilling ASTM A790 and ...

Open

12857

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 as required for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

12858

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets the minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) requirements per NORSOK MDS D51 Rev 6 and ASTM A790 references. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

12859

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

12860

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C (transverse: 45/35 J, longitudinal: 65/50 J) for thickness >6mm, and the specified pipe dimensions allow for required testing orientation and specimen size. Source: DM...

Open

12861

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

12862

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is required for micrographic examination, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

12863

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

12864

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STANDA...

Open

12865

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

12866

4.4.2

AI

No

add date

Findings of intermetallic phases must be reported, and acceptance is based on CVN and corrosion test results, fulfilling the requirement regarding centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

12867

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

12868

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

12869

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

12870

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with required etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impac...

Open

12871

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12872

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

12873

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including chemical composition, PRE, tensile, impact, corrosion, microstructure, ferrite content, and M-650 qualification for the specified wall thickness range. Source: ...

Open

12874

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02...

Open

12875

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

12876

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within capability range. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02...

Open

12877

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790, NORSOK M-630 MDS D51 Rev 6, and NORSOK M-650/ISO 17782 are not confirmed as fulfilled. For OD 219.1 mm, eddy current testing is not feasible, hydrostatic and ultrasonic tests are only available at extra cost, an...

Open

12878

5.2

AI

No

add date

The specific NDE acceptance criterion that any indication greater than the calibration notch is a defect requiring rejection or repair is not stated, and standard NDE is not available for the requested dimension at Montbard, so the requirement cannot...

Open

12879

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) as required, with no overriding specifications from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances ...

Open

12880

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12881

8.0

AI

No

add date

Marking per ASTM A790 §14 and standard Montbard plant methods (indelible ink, vibro-etching) include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK...

Open

12882

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12883

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA and specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

12884

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

12885

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or confirmed. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

12886

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, fulfilling the qualification requirement for the specified size and product f...

Open

12887

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to products and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest N...

Open

12888

10.2

AI

No

add date

Certification is provided to EN 10204 Type 3.1 and includes all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary or...

Open

12889

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, ladle chemical analysis, solution annealing parameters, or results of all required metal...

Open

12890

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, covering all standard and supplementary requirements, and are M-650 qualified. Source: Item Table, DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A...

Open

12891

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N (up to WT 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability or full compliance with both standards as required by the specification. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

12892

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm), matching the requested grade and wall thickness (18.26 mm), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 ...

Open

12893

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12894

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12895

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

12896

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

12897

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and per 100 pieces, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

12898

4.1

AI

No

add date

Test sampling for seamless pipes per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specified thickness...

Open

12899

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

12900

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfills the requirement as the pipe wall thickness exceeds the minimum required for testing per ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Imp...

Open

12901

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C: minimum 45/35 J (average/single, transverse) and 65/50 J (average/single, longitudinal) for thickness >6mm. The specified pipe dimensions allow for required testing ...

Open

12902

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with specified etchants for intermetallic phases and ferrite balance after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spec...

Open

12903

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH is specified for detecting ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

12904

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

12905

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STANDA...

Open

12906

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

12907

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

12908

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size, so the requirement is not fully fulfilled. Sou...

Open

12909

4.4.3

AI

No

add date

Ferrite content is determined per ASTM E562 or by image analysis according to ASTM E1245, performed in accordance with ISO 17781, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

12910

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781 with specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requirement f...

Open

12911

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

12912

4.5

AI

No

add date

No direct evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or planned is provided in the referenced documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

12913

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all metallurgical acceptance criteria per NORSOK M-630 MDS D51 Rev 6, NORSOK M-650/ISO 17782, and ASTM A790, including chemical composition (PRE ≥ 40), mechanical properties, microstructure, ferrite content (35-60%), and ...

Open

12914

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A @ 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

12915

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

12916

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within capability range. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02...

Open

12917

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. For the requested OD (219.1 mm), eddy current testing is only feasible with a multi-elements probe at extra cost and requires technical co...

Open

12918

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are classified as defects requiring rejection or repair; NDE acceptance criteria per the requirement are not stated or confirmed for the specified product and size. NDT feas...

Open

12919

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790) for the specified pipe size, with no deviations or overrides stated in the customer specification or part report/drawing. Source: DMV_STANDARD_BOOK/07-...

Open

12920

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12921

8.0

AI

No

add date

Marking per ASTM A790 includes heat and lot numbers, and standard marking methods (indelible ink, vibro-etching) at Montbard plant ensure full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

12922

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

12923

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

12924

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

12925

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification de...

Open

12926

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

12927

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with issuance and validation by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

12928

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical...

Open

12929

1.0

AI

No

add date

DMV 25.7N seamless pipes are 25 Cr Duplex stainless steel, fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all relevant chemical, mechanical, manufacturing, and testing requirements. M-650 qualification is confirmed for the ...

Open

12930

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence provided for QTR/MPCR availability as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

12931

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

12932

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard and required for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

12933

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed by heat analysis per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790....

Open

12934

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

12935

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

12936

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ...

Open

12937

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure at specified locations, is fulfilled. For the ordered pipe (OD 219.1 mm, WT 18...

Open

12938

4.2

AI

No

add date

Tensile testing is performed at room temperature per NORSOK MDS D51 Table 4, meeting the required properties and referencing ASTM A370 or ISO 6892-1 for tensile testing. Hardness testing is also performed as specified. Source: DMV_STANDARD_BOOK/02 - ...

Open

12939

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 and ASTM A790 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW for S32760. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

12940

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

12941

4.3

AI

No

add date

DMV 25.7N meets NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with specified minimum absorbed energy values for both transverse and longitudinal directions, and the pipe dimensions allow for required testing directions and specimen siz...

Open

12942

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

12943

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

12944

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

12945

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

12946

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

12947

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

12948

4.4.2

AI

No

add date

The referenced documents do not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed; isolated precipitates below 10µm are allowed, which does not meet the stricter client requirement of no intermetallics or prec...

Open

12949

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

12950

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

12951

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS ...

Open

12952

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

12953

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

12954

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

12955

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destruct...

Open

12956

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed on the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - U...

Open

12957

5.2

AI

No

add date

NDE per ASTM A790 is partially feasible (hydrostatic or NDE per ASTM A999), but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD (219.1 mm), eddy current test...

Open

12958

5.2

AI

No

add date

No document explicitly confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair; NDE acceptance criteria and feasibility for the specified dimension are not demonstrated for Montbard plant. ...

Open

12959

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the requested pipe, with no deviations or special tolerances specified by the customer, fulfilling the requirement. Source: DMV_STANDARD_BOOK/07.01 - General information...

Open

12960

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

12961

8.0

AI

No

add date

Marking per ASTM A790 §14 and standard Montbard plant methods (indelible ink, vibro-etching) include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK...

Open

12962

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

12963

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

12964

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

12965

10.1

AI

No

add date

Certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR as required, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the relevant wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

12966

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to the delivered products, fulfilling the documentation and traceability requirement as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

12967

10.2

AI

No

add date

Certification is provided to EN 10204 Type 3.1, including all information required by ASTM A790 and NORSOK M-630, and validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Cert...

Open

12968

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and results of all metallurgical and non-...

Open

12969

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the 'Norms / Customer Specifications' and confirmed by the digest, including all mechanical, chemical, and testing requirements....

Open

12970

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process follows M-650 (or ISO 17782) qualified procedures, fulfilling the requirement for manufacturer and process qualification per NORSOK M-6...

Open

12971

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition complies with Table 2 requirements for DMV 25.7N seamless pipe per ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - ...

Open

12972

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN ≥ 40, in accordance with NORSOK MDS D51 Rev 06 and ASTM A790 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

12973

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

12974

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

12975

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and per 100 pieces, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

12976

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure, is performed per NORSOK MDS D51/ASTM A790. For the ordered pipe (OD 219.1 mm,...

Open

12977

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

12978

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets or exceeds the required minimum tensile strength (750 MPa), yield strength (550 MPa), elongation (25%), and maximum hardness (310 HBW) per NORSOK MDS D51 Rev 06 and ASTM A790 for S32760. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

12979

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact ...

Open

12980

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C (transverse: 45/35 J, longitudinal: 65/50 J) for thickness >6mm, and the specified pipe dimensions allow for required testing directions and specimen sizes. Source: D...

Open

12981

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

12982

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is specified and fulfills the requirement for suitable etchant(s) as listed in ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

12983

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

12984

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782 as required; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

12985

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

12986

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, reported at actual magnification and including a scale bar, if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - ...

Open

12987

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

12988

4.4.2

AI

No

add date

The referenced documents do not prohibit all intermetallic phases and/or precipitates if CVN testing cannot be completed; isolated precipitates are allowed under certain conditions, which does not meet the stricter client requirement that none are pe...

Open

12989

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

12990

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

12991

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

12992

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

12993

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified per NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

12994

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

12995

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

12996

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

12997

5.2

AI

No

add date

NDE per ASTM A790 is partially addressed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782 requirements are met. Standard NDE methods are not fully available for the specified pipe size at Montbard, and full...

Open

12998

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair, and standard NDE methods are not feasible for the requested OD at Montbard, so the requirement is no...

Open

12999

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding customer specification indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A 376-02a...

Open

13000

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

13001

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

13002

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03...

Open

13003

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

13004

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

13005

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification dem...

Open

13006

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

13007

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630 for 25Cr Duplex Stainless Steel seamless pipe, validated by Quality Control and referencing M-650/ISO17782 qualification where applicable. So...

Open

13008

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or results of all required metallurgical and non-destructive testing. Only the country of...

Open

13009

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, Digest NORSOK ...

Open

13010

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782; no evidence of full qualification or availability of QTR/MPCR as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13011

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N within the required wall thickness range, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_...

Open

13012

3.1

AI

No

add date

AOD or equivalent refining is used 100% for DMV 25.7N, and chemical composition complies with the specified requirements in Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13013

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13014

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

13015

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

13016

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

13017

4.1

AI

No

add date

All required tests (tensile, hardness, CVN, corrosion, microstructure) are performed as specified, with correct directions and locations per NORSOK MDS D51 and ASTM A790. For the specified pipe dimensions, transverse CVN specimens are feasible and wi...

Open

13018

4.2

AI

No

add date

Tensile testing is performed at room temperature per relevant standards, with mechanical properties and hardness requirements matching Table 4, and compliance with ASTM A370 or ISO 6892-1 is confirmed. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

13019

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, fulfilling the client's mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

13020

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

13021

4.3

AI

No

add date

DMV 25.7N meets NORSOK MDS D51 Rev 6 impact test requirements: Charpy V-notch at -46°C, minimum 45 J average and 35 J single in transverse, 65 J average and 50 J single in longitudinal (if transverse not possible), with sub-size reduction factors. Th...

Open

13022

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching for intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and examination in accordance ...

Open

13023

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, is specified for micrographic examination as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

13024

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

13025

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

13026

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

13027

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

13028

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10µm, but does not prohibit all intermetallic phases/precipitates when CVN testing cannot be completed, as required by the client. Zero-tolerance is not confirmed for this scenario. S...

Open

13029

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed (ASTM A790) and white pickled or bright annealed (NORSOK MDS S01), directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790, NORSOK MDS S01.

Open

13030

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

13031

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, including etching methods, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on...

Open

13032

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13033

4.5

AI

No

add date

No explicit evidence of ASTM G48 Method 'A' (50˚C, 24h) corrosion testing in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

13034

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified according to NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

13035

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per NORSOK MDS D51 Rev 06 (ISO 17781, G48 Method A). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

13036

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

13037

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within machine capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

13038

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and M-650/ISO 17782 are not confirmed. Only ASTM A790/A999 NDE is referenced, which may not meet the more stringent NORSOK requirements. For the specified OD (219.1 mm), eddy current testing is not fea...

Open

13039

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair; NDE acceptance criteria and related rejection/repair policy are not specified for t...

Open

13040

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and referenced ASTM A999 for the specified pipe dimensions, with no alternative requirements stated by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolera...

Open

13041

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

13042

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

13043

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

13044

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

13045

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

13046

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

13047

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products as required by SIR205 and section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

13048

10.2

AI

No

add date

Certification is provided to EN 10204 Type 3.1, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference). Source: DMV_STANDARD_BOOK/02...

Open

13049

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and n...

Open

13050

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with explicit confirmation of compliance for grade UNS S32760 and all relevant mechanical, chemical, and te...

Open

13051

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of QTR/MPCR availability for review as required by the specification. Only M-650 accreditation is mentioned for MST-Tubes, not I...

Open

13052

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 (or ISO 17782), meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

13053

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N meets the chemical composition requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORS...

Open

13054

3.1

AI

No

add date

DMV 25.7N (UNS S32760) is manufactured according to NORSOK M-650 qualified procedures, with accreditation for the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORS...

Open

13055

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed in accordance with ASTM A790, and the manufacturing process is qualified to NORSOK M-650/ISO 17782 for DMV 25.7N. Free circulation of heating and cooling media is ensure...

Open

13056

4.4.2

AI

No

add date

No relevant documents address the reporting of centerline intermetallic stringers or acceptance criteria based on CVN and corrosion test results in such cases. Requirement not fulfilled. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in ...

Open

13057

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13058

4.1

AI

No

add date

No evidence that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is carried out for each heat and heat treatment lot as defined in ASTM A790; required testing frequency and lot definition are not confirmed in ...

Open

13059

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

13060

4.1

AI

No

add date

Test sampling details such as test direction (longitudinal or transverse per ASTM A790), CVN impact test requirements, and thickness locations are not fully specified in the provided documents. Tensile testing is confirmed but without direction; CVN ...

Open

13061

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature with criteria matching or exceeding Table 4, and compliance with NORSOK MDS D51 (which references ASTM A790) implies testing according to ASTM A370 or ISO 6892-1 for DMV 25.7N material. Source:...

Open

13062

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required in Table 4 are not confirmed or matched in the provided sources; only values for austenitic grade TP316L are given, which do not meet the duplex grade requir...

Open

13063

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, meeting the minimum wall thickness requirements for both ASTM and ISO standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Dest...

Open

13064

4.3

AI

No

add date

Pipe with OD 219.1 mm and WT 18.26 mm allows standard Charpy specimens; both longitudinal and transverse impact requirements at -46°C can be met for wall thickness > 6 mm. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-...

Open

13065

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination per ISO 17781 or use of the specified etchant for 25 Cr Duplex stainless steels; available information only covers grain size measurement for austenitic materials and excludes duplex grades. S...

Open

13066

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination is provided; available documentation is either not relevant or does not address this requirement. Source: DMV_STAN...

Open

13067

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic phases; isolated phases are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

13068

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided or addressed in the relevant documentation or comments. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/1...

Open

13069

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included at actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness if intermetallic phases a...

Open

13070

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

13071

4.4.2

AI

No

add date

Referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or allow isolated precipitates below 10µm, which does not meet the stricter client requirement of zero tolerance in ...

Open

13072

4.4.3

AI

No

add date

No information is provided confirming ferrite content determination per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781; only grain size measurement is discussed, not ferrite content analysis as required. Source: DMV_STANDARD_BOOK/12 - Special...

Open

13073

4.4.3

AI

No

add date

No provided document specifies acceptance criteria for micrographic examination or metallurgical properties relevant to section 4.4 Micrographic Examination for DMV 25.7N or the inquiry specification. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM ...

Open

13074

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13075

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided; only 'A790 NORSOK' is referenced, which does not confirm fulfillment of the requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion test...

Open

13076

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are provided in the referenced documents or section; only headings or general references are present without detailed requirements or values for validation. Source: DMV_STANDARD_BOOK/02 - S...

Open

13077

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

13078

5.1

AI

No

add date

No information is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feas...

Open

13079

5.2

AI

No

add date

No evidence that 100% ultrasonic testing for longitudinal defects is performed in accordance with ASTM E213 or ISO 10893-10, or that reference notches and test timing requirements are met. Dimensional limits for ultrasonic testing are specified, but ...

Open

13080

5.2

AI

No

add date

100% qualitative anti-mixing PMI is standard at Montbard for DMV 25.7N, with Cr, Ni, Mo checked, fulfilling the NDE/PMI requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-06 - Positive Material identific...

Open

13081

5.2

AI

No

add date

No provided document confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair for the specified pipe size; NDE feasibility and acceptance criteria are not demonstrated for this requirement o...

Open

13082

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for both hot and cold finished products, including the specified dimensions, are confirmed to be per the applicable ASTM standards (A 790 with A 999 for tolerances), with no deviations or exceptions note...

Open

13083

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13084

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/13 - Marking/13-02 - Standard marking feasibility/13-02-01 - Standard marking feasibility - Montbard pla...

Open

13085

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required for MST-Tubes in the specification digest. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 0...

Open

13086

10.0

AI

No

add date

No evidence of an appropriate quality-assurance system, such as ISO 9001 certification by a competent EEA body, is provided for the Montbard plant or any other plant. Relevant documents only reference inspection certificates and responsibilities, not...

Open

13087

10.1

AI

No

add date

No evidence that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-03 - Certif...

Open

13088

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

13089

10.2

AI

No

add date

No provided document confirms that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC as specified. No explicit mention of SIR205 or traceability to TechnipFMC is present in the reviewed documents. Source...

Open

13090

10.2

AI

No

add date

Material certificate will be issued according to EN 10204 Type 3.1 and, as standard practice when ASTM A790 and NORSOK M-630 are specified, will include the required information. Source: 14-03 - Certification Montbard plant.doc

Open

13091

10.2

AI

No

add date

No provided documentation includes NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or results of required metallurgical and non-destructive testin...

Open

13092

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Di...

Open

13093

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not to ISO 17782, as explicitly required. No evidence provided for QTR/MPCR availability or full compliance with both standards for the exact product supplied. Source: DMV_STANDARD_...

Open

13094

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

13095

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSO...

Open

13096

3.1

AI

No

add date

Chemical composition for UNS S32760 conforms to Table 2 of ASTM A790, matching the specified requirements, with heat analysis and supplier certification provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

13097

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. Free circulation of heating and cooling media is ensured by compliance with these standards. Source: DMV_STANDA...

Open

13098

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13099

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

13100

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, directly referencing Table 3 for test specimen sampling as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02...

Open

13101

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled. For the specified pipe dimensio...

Open

13102

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature according to ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

13103

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

13104

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfills the requirement as the pipe wall thickness exceeds the minimum required for testing per ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

13105

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C (transverse: 45/35 J, longitudinal: 65/50 J) for thickness >6mm, and the specified pipe dimensions allow for required testing directions and specimen sizes. Source: DM...

Open

13106

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

13107

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

13108

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

13109

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

13110

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

13111

4.4.2

AI

No

add date

Findings of intermetallic phases, including stringers, must be reported, and acceptance is based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

13112

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

13113

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

13114

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

13115

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13116

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

13117

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, chemical composition, ferrite content, corrosion, impact, PRE, tensile, and microstructure, and is M-650 qual...

Open

13118

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 24h, 50°C) is performed for DMV 25.7N, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m²; DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

13119

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source: DM...

Open

13120

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

13121

5.2

AI

No

add date

NDE per ASTM A790 is feasible, but NORSOK M-630 MDS D51/ISO 17782-specific NDE acceptance criteria are not validated. For the requested OD (219.1 mm), standard NDE (eddy current, hydrostatic, ultrasonic) is not available or only possible at extra cos...

Open

13122

5.2

AI

No

add date

None of the referenced documents explicitly confirm that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor do they confirm that this NDE acceptance criterion is standard pract...

Open

13123

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (A790/A999) for the requested pipe, with no deviations specified by the customer or TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolera...

Open

13124

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

13125

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

13126

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produc...

Open

13127

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

13128

7.0

AI

No

add date

ASTM A790 (6.1.3) and NORSOK MDS D51 (§13) both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

13129

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the specified quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

13130

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification dem...

Open

13131

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

13132

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

13133

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution annealing temperature/ho...

Open

13134

1.0

AI

No

add date

DMV 25.7N seamless pipes are 25 Cr Duplex stainless steel, manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with M-650 qualification, as specified. Source: Requested Positions Table, DM...

Open

13135

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

13136

3.1

AI

No

add date

AOD or equivalent steel refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13137

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and in accordance with ASTM A790 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat to ens...

Open

13138

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

13139

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

13140

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-0...

Open

13141

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

13142

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, is fulfilled for DMV 25....

Open

13143

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

13144

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

13145

4.3

AI

No

add date

Charpy V-notch testing is feasible and meets ASTM A370 and ISO 148-1 requirements for the specified pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in Montbar...

Open

13146

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact test requirements at -46°C, including minimum absorbed energy values and sub-size reduction factors. The specified pipe dimensions allow both longitudinal and transverse impact tests as required. S...

Open

13147

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with 20-40% NaOH or KOH solution after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

13148

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

13149

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

13150

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included with presence and location of intermetallic phases noted and recorded. Source: DMV_STANDA...

Open

13151

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, reported at actual magnification and including a scale bar, if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - ...

Open

13152

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases (including stringers) and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-0...

Open

13153

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates below 10μm, which does not meet the stricter requirement of no intermetallic...

Open

13154

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

13155

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

13156

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

13157

4.5

AI

No

add date

Requirement for no pitting at 20X magnification and weight loss less than 1.0 g/m² is met by compliance with ISO 17781: G48 Method A, as specified for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

13158

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

13159

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, which are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-0...

Open

13160

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. For the requested OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/ultrasonic testing is only available at extra cost ...

Open

13161

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair; NDE acceptance criteria and calibration notch reference are not explicitly stated or confirmed...

Open

13162

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding TechnipFMC specification identified. Source: 07.01 - General information.doc, 07.03.01 - Tolerances according to ASTM A 312-01a A 376-02a A 790-02 (A 999-01).doc, 02...

Open

13163

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

13164

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

13165

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03...

Open

13166

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

13167

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

13168

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness for the specified size and product form. Source: DMV_STANDARD_BOO...

Open

13169

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates traceable to delivered products, including required documentation as per SIR205 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

13170

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

13171

10.2

AI

No

add date

Most documentation and certification requirements are addressed, but the actual steel producer name is not provided (only country of origin), and explicit documentation for all required test results, solution annealing details, and NORSOK M-650/ISO 1...

Open

13172

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all standard and supplementary requirements, and are M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-03-01 - Digest A...

Open

13173

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR availability as required. Requirement is not fully fulfilled due to missing ISO 17782 accreditation and lack of evidence for documenta...

Open

13174

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process follows M-650 (or ISO 17782) qualified procedures, fulfilling the requirement for manufacturer and process qualification and compliance...

Open

13175

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13176

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

13177

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650/ISO 17782. Pipes are arranged to ensure free circulation of heating and c...

Open

13178

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, with test frequency specified as 1/lot, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

13179

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

13180

4.1

AI

No

add date

Tensile, hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests are performed on prolongation samples from seamless pipes per ASTM A790 and NORSOK MDS D51, with test directions and locations as specified. The o...

Open

13181

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

13182

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

13183

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for 18.26mm wall thickness and 219.1mm OD pipe as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impac...

Open

13184

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C (transverse: 45/35 J, longitudinal: 65/50 J) for thickness >6mm, and the specified pipe dimensions allow for required testing directions and specimen sizes. Source: DM...

Open

13185

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

13186

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is explicitly required for micrographic examination as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

13187

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

13188

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

13189

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, reported at actual magnification and including a scale bar, if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - ...

Open

13190

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 requires reporting of intermetallic phases, and acceptance is based on impact (CVN) and corrosion test results if intermetallic stringers are present, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - S...

Open

13191

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

13192

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 ...

Open

13193

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance is based on im...

Open

13194

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

13195

4.5

AI

No

add date

No direct evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or fulfilled in the referenced documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

13196

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, chemical composition, ferrite content, and corrosion/impact requirements. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

13197

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02...

Open

13198

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

13199

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

13200

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N with wall thickness up to 31.75 mm (hot finished), and manufacturing is according to M-650/ISO 17782 qualified procedures, fulfilling the requirement for manufacturer and process qualification and co...

Open

13201

5.2

AI

No

add date

There is no evidence that NDE acceptance criteria per ASTM A790, NORSOK M-630 MDS D51 Rev 6, or NORSOK M-650/ISO 17782 are fulfilled. For the specified OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only ava...

Open

13202

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor that the required NDE acceptance criteria are applied for the specified product...

Open

13203

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no deviations or special tolerances specified by the customer or TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV...

Open

13204

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

13205

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02...

Open

13206

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

13207

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

13208

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

13209

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number as required, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

13210

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

13211

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

13212

10.2

AI

No

add date

EN 10204 3.1 certificates include most required information (NORSOK M-650/ISO 17782 QTR number, steel melting practice, heat treatment, etc.), but only the country of origin of the steel supplier is provided, not the actual steel producer's name. The...

Open

13213

1.0

AI

No

add date

25 Cr Duplex stainless steel seamless pipes are specified as compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with DMV 25.7N (UNS S32760) fully meeting all mechanical, chemical, and testing requirements, and manufacturing process M-650 quali...

Open

13214

1.0

AI

No

add date

Supplier is NORSOK M-650 accredited for UNS S32760 / DMV25.7N but not accredited to ISO 17782 as required; no evidence provided for QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13215

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition complies with the specified requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13216

3.1

AI

No

add date

Chemical composition for S32760 matches Table 2 requirements and is confirmed to conform to ASTM A790 with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02...

Open

13217

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

13218

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

13219

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

13220

4.1

AI

No

add date

Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, are fulfilled. The...

Open

13221

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with tensile and hardness properties meeting Table 4 requirements for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13222

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

13223

4.3

AI

No

add date

Charpy V-notch testing is feasible and the requirement is fulfilled as the pipe wall thickness exceeds the minimum required for testing according to ASTM A370 and ISO 148-1 (min WT: 6.35 mm for ASTM, 8.74 mm for ISO). Source: DMV_STANDARD_BOOK/12 - S...

Open

13224

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal. The specified pipe dimensions allow...

Open

13225

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with specified etchants (20-40% NaOH or KOH for intermetallics, 10% oxalic acid or V2A followed by 20-40% NaOH or KOH for nitrides/carbides) after final polishing, fulfilling the requireme...

Open

13226

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect intermetallic phases, in accordance with ISO 17781, is explicitly required for micrographic examination, fulfilling the requirement for suitable etchants as listed in ISO 17781 Appendix B to show ferrite bal...

Open

13227

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

13228

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

13229

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected, fulfilling the requirem...

Open

13230

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 includes etching to detect intermetallic phases, with findings reported and acceptance based on CVN and corrosion test results as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

13231

4.4.2

AI

No

add date

The available specifications do not fully prohibit intermetallic phases and/or precipitates when CVN testing cannot be completed, as isolated precipitates below 10µm are permitted in the referenced document, which does not meet the client's requireme...

Open

13232

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

13233

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallics, isolated precipitates <10µm, carbides/nitrides reported), with acceptance b...

Open

13234

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

13235

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

13236

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 (ASTM A790, NORSOK M-630, M-650/ISO 17782) are fully met, including compliance for destructive and microstructural tests (tensile, impact, corrosion, microstructure, ferrite). ...

Open

13237

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

13238

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

13239

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed after all mechanical processing, heat treatments, and straightening, and the dimensional range is supported. Source: DMV_STANDARD_BOOK/12 - Special Testing/12...

Open

13240

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. Standard NDE (EC or UT) is not available for the required OD at Montbard without extra cost or technical advisor approval, and full-length...

Open

13241

5.2

AI

No

add date

No provided document explicitly states that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor confirms that NDE with this acceptance criterion will be performed as standard fo...

Open

13242

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and referenced ASTM A999, as required, with no overriding specifications indicated in the context. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according t...

Open

13243

4.4.2

AI

No

add date

No relevant documents address the detection, reporting, or acceptance criteria for centerline intermetallic stringers or link acceptance to CVN and corrosion test results.

Open

13244

8.0

AI

No

add date

Marking includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAND...

Open

13245

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

13246

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

13247

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

13248

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

13249

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

13250

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control and compliance indicated in the specification context. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORS...

Open

13251

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis results, solution annealing parameters, or results of all metallurgica...

Open

13252

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all standard and supplementary requirements, and are M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-03-01 - Digest A...

Open

13253

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability or full compliance with both standards as required by the specification. Source: DMV_STANDARD_BOOK/...

Open

13254

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

13255

3.1

AI

No

add date

AOD or equivalent steel refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13256

3.1

AI

No

add date

Chemical composition for S32760 matches Table 2 of ASTM A790 as required, and DMV material conforms with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-0...

Open

13257

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

13258

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, with test frequency specified as 1/lot. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

13259

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing the table for test specimen sampling as outlined in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

13260

4.1

AI

No

add date

Tensile, hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests are performed on prolongation samples from seamless pipes per ASTM A790 and NORSOK MDS D51, with test directions and locations as specified. For t...

Open

13261

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

13262

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

13263

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for 18.26mm wall thickness and 219.1mm OD pipe in both longitudinal and transverse directions as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive t...

Open

13264

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements, including Charpy V-notch testing at -46°C with minimum absorbed energy values (transverse: 45 J average/35 J single, longitudinal: 65 J average/50 J single) and reduction fac...

Open

13265

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified electrolytic etchant after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

13266

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

13267

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

13268

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded as required. Source...

Open

13269

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x with photos included, reported at actual magnification and including a scale bar, if intermetallic phases are not detected, at or near mid-wall thickness. Source: DMV_STANDARD_B...

Open

13270

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

13271

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size, so the requirement is not fully me...

Open

13272

7.0

AI

No

add date

ASTM A790 and NORSOK MDS S01 require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: ASTM A790, NORSOK MDS S01.

Open

13273

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

13274

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781 at ≥400X magnification, with acceptance criteria requiring the structure to be free from intermetallic precipitates (isolated, non-distributed, <10µm allowed); carbides/nitrides are reported, and ac...

Open

13275

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13276

4.5

AI

No

add date

ASTM G48 Method 'A' corrosion testing at 50°C for 24h in accordance with ISO 17781 is not explicitly mentioned or confirmed; compliance cannot be validated based on the available information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Mon...

Open

13277

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified according to NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

13278

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

13279

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

13280

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within capability range. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02...

Open

13281

5.2

AI

No

add date

NDE per ASTM A790/NORSOK is not fully fulfilled for the requested pipe size at Montbard: eddy current testing is not feasible, hydrostatic and ultrasonic tests are only available at extra cost, and standard feasibility for required NDE is not confirm...

Open

13282

5.2

AI

No

add date

No provided document explicitly confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that such NDE acceptance criteria are applied as standard practice for the specified product and si...

Open

13283

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A...

Open

13284

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

13285

8.0

AI

No

add date

Marking per ASTM A790 and plant marking methods ensure mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

13286

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

13287

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13288

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

13289

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

13290

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

13291

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

13292

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630 for 25Cr Duplex Stainless Steel seamless pipe, with validation by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D...

Open

13293

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice, refining method, heat treatment condition, heat number, chemical analysis, and test results, but only the country of origin of the steel supplie...

Open

13294

1.0

AI

No

add date

DMV 25.7N seamless pipes are 25 Cr Duplex stainless steel, fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all relevant chemical, mechanical, manufacturing, and testing requirements. M-650 qualification is confirmed for the ...

Open

13295

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N but lacks ISO 17782 accreditation; no evidence of QTR/MPCR availability as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13296

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

13297

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13298

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the requirement table and is confirmed to conform to ASTM A790 Table 2. Heat analysis is performed per heat as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dige...

Open

13299

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

13300

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, with test frequency specified as 1/lot and lot definition referenced from ASTM A790 §9.1. S...

Open

13301

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

13302

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50°C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Compliance cannot be confirmed without this information. Source: DMV_STANDARD_BOOK/12-...

Open

13303

4.1

AI

No

add date

Tensile, hardness, CVN (transverse or longitudinal if not possible), corrosion, and microstructure tests are performed on prolongation samples from seamless pipes per ASTM A790 and NORSOK MDS D51, with test directions and sampling locations as specif...

Open

13304

4.2

AI

No

add date

Tensile and hardness testing are performed in accordance with ASTM A370 or ISO 6892-1, and the material meets the specified tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

13305

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

13306

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, meeting the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 -...

Open

13307

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum absorbed energy values (transverse: 45 J average/35 J single; longitudinal: 65 J average/50 J single if transverse not possible), and...

Open

13308

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, with specified etchants (NaOH/KOH for intermetallics, oxalic acid or V2A plus NaOH/KOH for nitrides/carbides) used after final polishing as required....

Open

13309

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution for detecting ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

13310

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

13311

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STANDA...

Open

13312

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

13313

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_ST...

Open

13314

4.4.2

AI

No

add date

No provided documentation confirms that intermetallic phases and/or precipitates are completely prohibited when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10μm, which does not meet the stricter client re...

Open

13315

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

13316

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corr...

Open

13317

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including chemical composition, PRE, tensile, impact, corrosion, microstructure, ferrite content, and M-650 qualification for the specified wall thickness range. Source: ...

Open

13318

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

13319

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

13320

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultr...

Open

13321

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed; only ASTM A790/A999 NDE is detailed. For the specified OD (219.1 mm), eddy current testing is not feasible, hydrostatic and ultrasonic tests are only avail...

Open

13322

5.2

AI

No

add date

None of the relevant documents explicitly state that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair of pipe and tubing, nor do they confirm that NDE with this acceptance criterion ...

Open

13323

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A...

Open

13324

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

13325

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-0...

Open

13326

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

13327

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

13328

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

13329

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, and the QTR number is included in the certificate, fulfilling the requirement for supplier qualification documentation per SIR131. Source: DMV_STANDARD_BOOK/0...

Open

13330

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

13331

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAN...

Open

13332

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all required metallurgic...

Open

13333

1.0

AI

No

add date

DMV 25.7N seamless pipes are 25 Cr Duplex stainless steel, fully compliant with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with M-650 qualification up to the required wall thickness. Source: Requested Positions Table...

Open

13334

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence provided for QTR/MPCR availability or full compliance with both standards as required by the specification. Source: DMV_STANDARD...

Open

13335

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

13336

3.1

AI

No

add date

AOD or equivalent steel refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13337

3.1

AI

No

add date

DMV 25.7N (UNS S32760) chemical composition matches the requirement table and complies with ASTM A790 and NORSOK MDS D51 Rev 06, including PREN 3 40.0. Heat analysis and supplier certification are performed per heat as required. Source: 02-03-01 - D...

Open

13338

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification will state heat treatment condition as per ASTM A790. Pipes are processed to ensure ...

Open

13339

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

13340

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ...

Open

13341

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations per NORSOK MDS D51/ASTM A790. F...

Open

13342

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with tensile and hardness properties meeting Table 4 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Diges...

Open

13343

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

13344

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and meets the requirements of ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in ...

Open

13345

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements, including Charpy V-notch testing at -46°C with minimum absorbed energy values (transverse: 45 J avg/35 J single, longitudinal: 65 J avg/50 J single) and sub-size reduction factors. Th...

Open

13346

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

13347

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

13348

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

13349

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

13350

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, reported at actual magnification and including a scale bar, if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - ...

Open

13351

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 requires reporting of intermetallic phases, with acceptance based on CVN and corrosion test results if such phases are present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STAN...

Open

13352

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits all intermetallic phases and/or precipitates if CVN testing cannot be completed. No source fully prohibits intermetallics as required by th...

Open

13353

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

13354

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and ...

Open

13355

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is specified and fulfilled for DMV 25.7N according to NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

13356

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or documented. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

13357

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13358

4.5

AI

No

add date

DMV 25.7N undergoes a pitting corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_...

Open

13359

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712 or equivalent standards. Requirement not fulfilled based on available...

Open

13360

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/1...

Open

13361

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT) is confirmed, but NORSOK-specific NDE requirements and ISO qualification are not addressed. For the requested OD (219.1 mm), eddy current testing is only feasible with a multi-elements probe at extra co...

Open

13362

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair; the specific calibration notch-based NDE acceptance criterion is not explicitly stated or conf...

Open

13363

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790) for the requested pipe dimensions, with no deviations specified by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_...

Open

13364

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06...

Open

13365

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot, and standard marking methods (indelible ink, vibro-etching) include heat and lot numbers as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

13366

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' for MST-Tubes, covering DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-0...

Open

13367

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body established within the EEA and specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

13368

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

13369

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV 25.7N up to WT = 31.75 mm, covering the requested size, and the EN 10204 3.1 certificate will include the required NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number. Sour...

Open

13370

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

13371

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control as per specification requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.do...

Open

13372

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or complete metallurgical and NDT resu...

Open

13373

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified up to the required wall thickness. Source: DMV_STANDAR...

Open

13374

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR availability as required. Full qualification to both NORSOK M-650 and ISO 17782 is not demonstrated for the exact product ...

Open

13375

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

13376

3.1

AI

No

add date

AOD or equivalent refining is used and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13377

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed by supplier certification and heat analysis per ASTM A790 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dige...

Open

13378

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

13379

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

13380

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Dige...

Open

13381

4.1

AI

No

add date

All required tests (tensile, hardness, CVN, corrosion, microstructure) are performed on DMV 25.7N seamless pipes as per NORSOK MDS D51 and ASTM A790, with correct test directions and thickness locations. The ordered pipe dimensions allow for transver...

Open

13382

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-...

Open

13383

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

13384

4.3

AI

No

add date

Charpy V-notch testing is feasible and the requirement is fulfilled for the specified pipe dimensions according to ASTM A370 and ISO 148-1 minimum wall thickness criteria. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-...

Open

13385

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energy values of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if required. The specified pipe...

Open

13386

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with specified etchants applied after final polishing as required for 25 Cr Duplex stainless steels. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

13387

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

13388

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

13389

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STANDA...

Open

13390

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, reported at actual magnification and including a scale bar, if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - ...

Open

13391

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/...

Open

13392

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

13393

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

13394

4.4.3

AI

No

add date

Microstructure examination per ISO 17781 is specified, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impac...

Open

13395

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

13396

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is fulfilled; neither ASTM G48 nor ISO 17781 nor the specific test conditions are mentioned in the relevant documentation. Source: DMV_STANDARD_BOOK/1...

Open

13397

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, as well as manufacturing, heat treatment, and qualification requirements. Source: DMV_STAN...

Open

13398

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m²; DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

13399

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

13400

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed after all processing steps for the required dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultrasonic t...

Open

13401

5.2

AI

No

add date

NDE per ASTM A790 is generally feasible, but there is no evidence that additional NDE requirements of NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782 are met. Eddy current testing is not feasible for the required OD except with multi-elements probe (e...

Open

13402

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13403

5.2

AI

No

add date

The requirement that any indication greater than the calibration notch is a defect, with defective pipe/tubing to be rejected or repaired, is not explicitly stated or confirmed in the referenced specifications or feasibility documents for the request...

Open

13404

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standards (including A999), with no deviations specified by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolera...

Open

13405

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

13406

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 (§14), both requiring full traceability to melt and heat treatment lot. Marking methods include heat number and DMV lot number, ensuring compliance with the requirement for traceability. S...

Open

13407

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

13408

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dige...

Open

13409

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling supplier qualification documentation requirem...

Open

13410

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO 17782 manufacturing summary or QTR number, are provided and fulfill the requirement for documentation traceable to the products and tran...

Open

13411

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 ...

Open

13412

10.2

AI

No

add date

Most documentation and certification requirements are addressed except for the 'Steel producer of the starting material,' which is not fully fulfilled as only the country of origin is provided, not the actual producer name. All other required documen...

Open

13413

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the requested positions and confirmed in the digest, including all relevant mechanical, chemical, corrosion, and qualification requirements. So...

Open

13414

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N but not to ISO 17782, as explicitly required. No evidence of QTR/MPCR documentation availability for review. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spe...

Open

13415

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

13416

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis conforms to Table 2 requirements for DMV 25.7N seamless pipe as per ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13417

3.1

AI

No

add date

Chemical composition for S32760 matches Table 2 of ASTM A790 as required, and DMV material composition conforms with supplier certification and heat analysis per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed d...

Open

13418

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

13419

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

13420

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/...

Open

13421

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled. For the offered pipe (219.1 mm ...

Open

13422

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370, with required properties (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and hardness testing in HRC; DMV 25.7N complies with these requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

13423

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

13424

4.3

AI

No

add date

Charpy V-notch testing is feasible and the requirement is fulfilled as the pipe wall thickness exceeds the minimum required for testing according to ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/1...

Open

13425

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for required testing directions and specimen sizes. ...

Open

13426

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with specified etchants for intermetallic phases and ferrite balance applied after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spec...

Open

13427

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, is required for micrographic examination as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

13428

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

13429

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

13430

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

13431

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13432

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/...

Open

13433

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates, which does not meet the stricter client requirement of no intermetallics or...

Open

13434

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

13435

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

13436

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

13437

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

13438

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, with M-650 qualification up to the specified wall thickness. Source: DMV_STANDARD_BOOK/02 ...

Open

13439

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

13440

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor are their roles and responsibilities as defined in ISO 9712 addressed. Source: DMV_STANDARD_BOOK/12-02-01 - Non d...

Open

13441

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

13442

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790/NORSOK M-630 MDS D51 are not fully addressed; only standard hydrostatic or EC/UT testing per ASTM A999 is confirmed, with no explicit evidence for NORSOK-specific NDE. For OD 219.1 mm, EC and UT are only availabl...

Open

13443

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are considered defects requiring rejection or repair; NDE acceptance criteria not detailed for the requirement; NDE feasibility for the specified size is not confirmed as st...

Open

13444

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790/A999) for the specified pipe, with no overriding requirements stated by the client or in the drawing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/07-01 -...

Open

13445

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

13446

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

13447

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

13448

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 explicitly states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NO...

Open

13449

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

13450

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the specified quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

13451

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling the requirement for supplier qualification do...

Open

13452

10.2

AI

No

add date

Certification includes EN 10204 type 3.1 with traceability to heat treatment, steel manufacturer, melting/refining practice, and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number; MST-Tubes is ISO 9001 certified, ensuring documentation is tra...

Open

13453

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and covering required details such as heat treatment, steel manufacturer, melting and refining practice, and ...

Open

13454

10.2

AI

No

add date

Most documentation and certification requirements are covered except for the specific steel producer of the starting material, which is not provided (only country of origin is given). Actual documentation or data for the specific order (such as heat ...

Open

13455

1.0

AI

No

add date

DMV 25.7N seamless pipes are 25 Cr Duplex stainless steel, fully compliant with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, as specified in the item table and confirmed by product digests. Manufacturing is M-650 quali...

Open

13456

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability for review is provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

13457

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

13458

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard and required for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

13459

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 06, including PREN ≥ 40 and all specified element limits and ranges for S32760. Source: DMV_STANDARD_BOOK/02-03-01 - Dige...

Open

13460

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

13461

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, meeting the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest N...

Open

13462

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

13463

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

13464

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests are performed at the spec...

Open

13465

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, with material meeting the tensile and maximum hardness properties of Table 4 as required for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

13466

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

13467

4.3

AI

No

add date

Pipe wall thickness exceeds the minimum required for Charpy V-notch testing per ASTM A370 and ISO 148-1, making testing feasible and fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Imp...

Open

13468

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C (transverse: avg 45 J, single 35 J; longitudinal: avg 65 J, single 50 J if transverse not possible). The specified pipe dimensions allow for required transverse Charp...

Open

13469

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

13470

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is required for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

13471

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

13472

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

13473

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

13474

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

13475

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size. No document fully prohibits intermetallics/pre...

Open

13476

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

13477

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance is based on im...

Open

13478

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

13479

4.5

AI

No

add date

ASTM G48 Method 'A' corrosion testing at 50°C for 24h in accordance with ISO 17781 is not explicitly mentioned or referenced; compliance cannot be confirmed based on the available information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Mo...

Open

13480

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

13481

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13482

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor are their roles and responsibilities defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructiv...

Open

13483

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed on the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

13484

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled. Standard NDE methods (hydrostatic, ultrasonic, eddy current) for the requested OD (219.1 mm) are only available at extra cost or require speci...

Open

13485

5.2

AI

No

add date

The specific NDE acceptance criterion that any indication greater than the calibration notch is a defect requiring rejection or repair is not detailed in the referenced documents, and standard NDE is not available for the requested OD 219.1 mm at Mon...

Open

13486

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the specified pipe size, with no deviations or special tolerances stated in the customer specification or part report/drawing. Source: DMV_STANDARD_BOOK/07-01 - General ...

Open

13487

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be pickled or bright annealed, fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

13488

8.0

AI

No

add date

Marking per ASTM A790 and plant marking methods ensure mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSO...

Open

13489

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

13490

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

13491

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified s...

Open

13492

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to delivered products, fulfilling the documentation and traceability requirements for TechnipFMC as specified in SIR205. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

13493

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

13494

10.2

AI

No

add date

Most required documentation and certification details (NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, metallurgical and non-destructive testing results) are eith...

Open

13495

1.0

AI

No

add date

25 Cr Duplex stainless steel seamless pipes (DMV 25.7N) are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification and all relevant mechanical, chemical, and testing requirements met. Source: DMV_STAN...

Open

13496

1.0

AI

No

add date

No provided document confirms supplier qualification to NORSOK M-650/ISO 17782 for the exact product (DMV 25.7N, WT 18.26 mm) or the availability of QTR/MPCR for review as required by the specification. Source: DMV_STANDARD_BOOK/02-03-01 - Digest AST...

Open

13497

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

13498

3.1

AI

No

add date

AOD or equivalent steel refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13499

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed by supplier certification and heat analysis per ASTM A790 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dige...

Open

13500

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is covered by compliance...

Open

13501

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion, and microstructure tests is performed per heat and heat treatment lot as defined by ASTM A790, matching the requirement for DMV 25.7N (UNS S32760). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

13502

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ...

Open

13503

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specifi...

Open

13504

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

13505

4.3

AI

No

add date

Pipe wall thickness exceeds minimum required for Charpy V-notch testing; testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - I...

Open

13506

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, including minimum absorbed energy values for transverse and longitudinal directions, and the specified pipe dimensions allow for required testing directions and spec...

Open

13507

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with specified etchants after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

13508

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

13509

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

13510

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs are included as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

13511

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

13512

4.4.2

AI

No

add date

Findings of intermetallic phases must be reported, and acceptance is based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dige...

Open

13513

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size, so the requirement is not fully me...

Open

13514

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

13515

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and ...

Open

13516

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13517

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

13518

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N, with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/0...

Open

13519

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

13520

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/1...

Open

13521

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled; standard NDE methods (eddy current, hydrostatic, ultrasonic, dye penetrant) are either not feasible, only available at extra cost, or no...

Open

13522

5.2

AI

No

add date

No provided document explicitly states that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair; NDE acceptance criteria are not specified for the requirement or the requested pipe dime...

Open

13523

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no deviations specified by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A 376-02a A 790...

Open

13524

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

13525

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

13526

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

13527

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

13528

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

13529

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demonst...

Open

13530

10.2

AI

No

add date

Certification includes EN 10204 type 3.1 with full traceability and ISO 9001 certification, fulfilling the requirement for documentation to be transmitted to TechnipFMC and traceable to the products (SIR205). Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

13531

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced throughout the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS...

Open

13532

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C (transverse: 45/35 J, longitudinal: 65/50 J) for thickness >6mm, and the specified pipe dimensions allow for required testing directions and specimen sizes. Source: DM...

Open

13533

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the customer requirements and confirmed by the digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Requested Posi...

Open

13534

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive te...

Open

13535

1.0

AI

No

add date

DMV 25.7N seamless pipes are 25 Cr Duplex stainless steel, fully compliant with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 Rev 6, as specified in the inquiry and confirmed by product digests. Manufacturing is M-650 qualified...

Open

13536

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

13537

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

13538

3.1

AI

No

add date

AOD or equivalent refining is required and applied for DMV 25.7N, and chemical composition complies with Table 2 of ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13539

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed by heat analysis per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790....

Open

13540

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

13541

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

13542

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

13543

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations, is fulfilled for DMV 25.7N pipes pe...

Open

13544

4.2

AI

No

add date

Tensile testing is performed at room temperature in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

13545

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

13546

4.3

AI

No

add date

Pipe wall thickness exceeds the minimum required for Charpy V-notch testing per ASTM A370 and ISO 148-1, making testing feasible and requirement fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact t...

Open

13547

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

13548

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is required for micrographic examination, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

13549

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement for distribution and size of intermetallic phases. So...

Open

13550

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

13551

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, actual magnification reported, and a scale bar included if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

13552

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

13553

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

13554

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

13555

4.4.3

AI

No

add date

Microstructure examination per ISO 17781 is specified, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impac...

Open

13556

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

13557

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

13558

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 are fully met, with DMV 25.7N compliant for all required destructive and microstructural tests (tensile, impact, corrosion, micrographic, ferrite). Source: DMV_STANDARD_BOOK/02...

Open

13559

4.5

AI

No

add date

DMV 25.7N meets the corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours, with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

13560

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

13561

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

13562

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not validated; only ASTM A790/A999 NDE is confirmed. For the specified OD (219.1 mm), standard NDE methods (Eddy current, Hydrostatic, Ultrasonic) are not fully fea...

Open

13563

5.2

AI

No

add date

No provided documentation explicitly states that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor confirms standard NDE process capability for the specified pipe size and requirement. Source:...

Open

13564

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no deviations or overrides specified by TechnipFMC. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according...

Open

13565

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be pickled or bright annealed, fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

13566

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

13567

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

13568

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system certified within the EEA and specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

13569

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

13570

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the size and p...

Open

13571

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products being delivered as required by SIR205 and section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

13572

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO177...

Open

13573

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, steel melting practice, heat number, chemical analysis, solution annealing details, and results of all metallurgical and non-destructive...

Open

13574

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782, and there is no evidence of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

13575

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

13576

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13577

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed by supplier certification and heat analysis per ASTM A790 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dige...

Open

13578

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is qualified to NORSOK M-650/ISO 17782, and MST-Tubes is M-650 accredited for DMV 25.7N. Certification will state heat treatment per ASTM A790. Free circ...

Open

13579

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

13580

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

13581

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations, in compliance with ASTM A790 and NORSOK ...

Open

13582

4.2

AI

No

add date

Tensile testing is performed at room temperature per §7, meeting Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%, and hardness testing is performed per ASTM A790. Testing per ASTM A370 or ISO 6892-1 is referenced, and compliance with NORSOK MDS D51 is confirm...

Open

13583

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produc...

Open

13584

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Im...

Open

13585

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energy values for both transverse and longitudinal directions, and the specified pipe dimensions allow for required transverse Charpy V-notch t...

Open

13586

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

13587

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

13588

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: ASTM A 790.docx, NORSOK MDS D51 Rev 06.docx

Open

13589

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

13590

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

13591

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

13592

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

13593

4.4.2

AI

No

add date

The referenced documents do not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed; isolated precipitates below 10µm are allowed, which does not meet the stricter client requirement of no intermetallics or prec...

Open

13594

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

13595

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Acceptance criteria require the structure to be free from intermetallic precipitates, with isolated prec...

Open

13596

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13597

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

13598

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

13599

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

13600

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

13601

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultr...

Open

13602

5.2

AI

No

add date

NDE per ASTM A790 and NORSOK M-630 MDS D51 is required, but available evidence only confirms standard hydrostatic or NDE (EC/UT) per ASTM A999, not NORSOK-specific criteria. For the specified OD (219.1 mm), eddy current testing is not feasible, and u...

Open

13603

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor is there confirmation that the required NDE acceptance criterion is standard or...

Open

13604

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the specified pipe size, with no deviations or overrides indicated in the customer specification or context. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, D...

Open

13605

8.0

AI

No

add date

Marking per ASTM A790 and plant marking methods ensure mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSO...

Open

13606

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

13607

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

13608

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

13609

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

13610

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products being delivered as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

13611

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 ...

Open

13612

10.2

AI

No

add date

Most documentation and certification requirements are addressed except for the 'Steel producer of the starting material,' which is not fully met as only the country of origin is provided, not the specific producer. No evidence is provided for actual ...

Open

13613

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/...

Open

13614

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782 as required; no evidence of QTR/MPCR availability. Requirement not fully fulfilled for NORSOK M-650/ISO 17782 qualification and documentation ...

Open

13615

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, fulfilling the requirement for manufacturer and process qualification and compliance with...

Open

13616

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13617

3.1

AI

No

add date

UNS S32760 chemical composition matches Table 2 requirements and DMV material composition conforms with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03...

Open

13618

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

13619

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

13620

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

13621

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified lo...

Open

13622

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

13623

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

13624

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfills the requirement as the pipe wall thickness exceeds the minimum required for testing per ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

13625

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C (transverse: 45/35 J, longitudinal: 65/50 J) for thickness >6mm, and the specified pipe dimensions allow for both longitudinal and transverse Charpy V-notch testing as...

Open

13626

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

13627

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

13628

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

13629

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded as required. Source...

Open

13630

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

13631

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

13632

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

13633

4.4.2

AI

No

add date

The available specifications allow isolated intermetallic precipitates below 10μm, which does not meet the stricter requirement that intermetallic phases and/or precipitates are not permitted if CVN testing cannot be completed due to geometry or size...

Open

13634

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

13635

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corrosi...

Open

13636

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS ...

Open

13637

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

13638

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 (ASTM A790, NORSOK M-650/ISO 17782) are fully met for DMV 25.7N, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - ...

Open

13639

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A @ 50°C, 24h) is performed with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these requirements. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

13640

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

13641

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed on the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

13642

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. For the requested OD (219.1 mm), eddy current testing is not standard and only available at extra cost with technical consultation; hydros...

Open

13643

5.2

AI

No

add date

None of the relevant documents explicitly confirm that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair; NDE acceptance criteria based on calibration notch are not specified for the ...

Open

13644

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) as required, with no overriding specifications from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances ...

Open

13645

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

13646

8.0

AI

No

add date

Marking per ASTM A790 §14 and standard Montbard plant methods (indelible ink, vibro-etching) include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NO...

Open

13647

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13648

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

13649

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

13650

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, meeting the required quality-assurance system per the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 R...

Open

13651

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, and the QTR number is included as per M-650 qualification, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/...

Open

13652

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

13653

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAN...

Open

13654

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and...

Open

13655

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all standard, supplementary, and quality requirements. M-650 qualification is confirmed for the required wall thickness. Source: DM...

Open

13656

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782, as explicitly required. No evidence of QTR/MPCR availability or full compliance with both standards is provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

13657

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

13658

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13659

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN requirements as per Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 6 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51...

Open

13660

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is qualified to NORSOK M-650/ISO 17782, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by complian...

Open

13661

4.5

AI

No

add date

No specific acceptance criteria are provided in the requirement, making validation impossible. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

13662

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

13663

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - De...

Open

13664

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests, with specified locations and directions, is fulfilled for DMV 25.7N per ...

Open

13665

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, with material meeting the tensile and maximum hardness properties of Table 4 as required for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

13666

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

13667

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfilled for the specified pipe dimensions according to ASTM A370 and ISO 148-1 requirements for minimum wall thickness. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Imp...

Open

13668

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements, including Charpy V-notch testing at -46°C with minimum absorbed energies (transverse: 45 J average/35 J single, longitudinal: 65 J average/50 J single) and sub-size reduction factors....

Open

13669

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with specified etchants for intermetallic phases and ferrite balance after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

13670

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

13671

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

13672

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases. Source: DMV_STANDARD_BOOK/02...

Open

13673

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

13674

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

13675

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

13676

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

13677

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corro...

Open

13678

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13679

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

13680

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified per NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

13681

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m²; DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02 - S...

Open

13682

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

13683

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

13684

5.2

AI

No

add date

NDE per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 is not confirmed; only ASTM A790/A999 NDE is detailed, and required NDE methods (eddy current, ultrasonic, hydrostatic, dye penetrant) are either not standard, not feasible, or only available at...

Open

13685

5.2

AI

No

add date

The provided documents do not specify that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, nor do they confirm that the required NDE with this acceptance criterion will be performe...

Open

13686

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are confirmed to be per the applicable ASTM standard (ASTM A999), with no deviations or special tolerances specified by the customer or TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General info...

Open

13687

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

13688

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and standard Montbard practices. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_...

Open

13689

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

13690

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

13691

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

13692

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the size and pr...

Open

13693

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability and required manufacturing and quality information, fulfilling the requirement for documentation traceable to the products delivered to TechnipFMC. Source: ...

Open

13694

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630 for 25Cr Duplex Stainless Steel seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-0...

Open

13695

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of metallurgical and non-de...

Open

13696

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with explicit coverage of mechanical, chemical, and testing requirements for the specified grade and produc...

Open

13697

1.0

AI

No

add date

Supplier is qualified according to NORSOK M-650/ISO 17782 for the exact product supplied using a qualified manufacturing procedure. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-0...

Open

13698

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N up to the required wall thickness, and the manufacturing process is qualified according to M-650 and meets NORSOK MDS D51 Rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

13699

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes and DMV 25.7N complies with the required chemical analysis. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORS...

Open

13700

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the inquiry WT is 18.26 mm, within the accredited range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

13701

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed per ASTM A790, with manufacturing process and furnaces qualified according to NORSOK M-650 or ISO 17782. Free circulation of heating and cooling media is ensured by comp...

Open

13702

4.1

AI

No

add date

There is no evidence that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is carried out for each heat and heat treatment lot as defined in ASTM A790. Required tests and frequency per lot are not confirmed in ...

Open

13703

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

13704

4.1

AI

No

add date

Tensile and hardness tests per ASTM A790 are confirmed, but there is no evidence of CVN impact testing or corrosion/microstructure tests, nor confirmation of required test sampling details (test direction, thickness location) as specified in Table 3 ...

Open

13705

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature with criteria matching or exceeding Table 4, and hardness testing is also performed. Compliance with NORSOK MDS D51 and DMV 25.7N is stated, which aligns with the required standards and propert...

Open

13706

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required in Table 4 are not confirmed; referenced documents either do not list the required values or pertain to a different steel grade (316/316L, not S32760/S32750)...

Open

13707

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, meeting the minimum wall thickness requirements for both standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testi...

Open

13708

4.3

AI

No

add date

Pipe dimensions allow for transverse Charpy specimens; impact properties at -46°C with specified absorbed energies are feasible and can be fulfilled for this product. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

13709

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination per ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels. Grain size examination is only discussed for austenitic materials, not duplex steels....

Open

13710

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchants as per ISO 17781 Appendix B for micrographic examination; requirement not fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Mi...

Open

13711

4.4.2

AI

No

add date

The micrographic examination requirements specify that the microstructure must be basically free from intermetallic precipitates, with isolated precipitates allowed if not homogeneously distributed and each below 10 μm, matching the client's requirem...

Open

13712

4.4.2

AI

No

add date

No information or micrographs regarding the presence and location of intermetallic phases at 400x magnification are provided or addressed in the relevant documentation. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-...

Open

13713

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at actual magnification with a scale bar if intermetallic phases are not detected. Magnification and photo inclusion are mentioned, but not all requir...

Open

13714

4.4.2

AI

No

add date

No relevant documents address the detection, reporting, or acceptance criteria for centerline intermetallic stringers, nor their linkage to CVN or corrosion test results as required. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-...

Open

13715

4.4.2

AI

No

add date

Relevant documents allow isolated intermetallic precipitates below 10μm if not distributed over the whole specimen, but do not prohibit all intermetallic phases/precipitates when CVN testing cannot be completed, as required by the specification. Zero...

Open

13716

4.4.3

AI

No

add date

No evidence of ferrite content measurement by ASTM E 562 or ASTM E 1245 in accordance with ISO 17781; only grain size measurement is addressed, not the required methods or standards for ferrite content determination. Source: DMV_STANDARD_BOOK/12 - Sp...

Open

13717

4.4.3

AI

No

add date

No acceptance criteria for micrographic examination are specified or addressed for DMV 25.7N in the provided sources; only procedures and standards are mentioned without required values or results for the order in question. Source: DMV_STANDARD_BOOK/...

Open

13718

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13719

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13720

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 G48 Method A at 25°C for 24 hours is required, with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the client's requirements. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

13721

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

13722

5.2

AI

No

add date

No confirmation that 100% ultrasonic testing per ASTM E213 or ISO 10893-10 is performed after all processing, nor that reference notches meet Figure 3 of ASTM E213 requirements. Dimensional limits for UT are provided, but not fulfillment of the full ...

Open

13723

5.2

AI

No

add date

100% qualitative anti-mixing PMI is standard at Montbard using appropriate instruments, with quantitative PMI available if required, fulfilling general NDE acceptance criteria for PMI. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destru...

Open

13724

5.2

AI

No

add date

No provided document confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor that this acceptance criterion is standard or feasible for the specified pipe dimension at Montbard. NDE fe...

Open

13725

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed as per the applicable ASTM standards (including ASTM A790/A999) for the requested dimensions, with no TechnipFMC override indicated. Requirement is fulfilled per client specification and re...

Open

13726

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and white pickled or bright annealed per NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790 diges...

Open

13727

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/13 - Marking/13-02 - Standard marking feasibility/13-02-01 - Standard markin...

Open

13728

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS S01 Rev 05 for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 ....

Open

13729

10.0

AI

No

add date

No evidence provided of an appropriate quality-assurance system (such as ISO 9001 certification by a competent EEA body) for the material manufacturer or Montbard plant. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-...

Open

13730

10.1

AI

No

add date

No evidence of an ISO 9001 quality-assurance system certified by a competent EEA body with a specific assessment for materials is provided, nor confirmation of submission of required documentation to TechnipFMC for approval. Source: DMV_STANDARD_BOOK...

Open

13731

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

13732

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

13733

10.2

AI

No

add date

No provided document confirms that documentation traceable to the products and transmitted to TechnipFMC as required by SIR205 will be provided. No explicit evidence of compliance with this requirement is present in the relevant sources. Source: DMV_...

Open

13734

10.2

AI

No

add date

Material certificate is issued according to EN 10204 Type 3.1 and validated by Quality Control for mill inspection. Inclusion of ASTM A790 and NORSOK M-630 information is not directly confirmed. Source: 14-03 - Certification Montbard plant.doc

Open

13735

10.2

AI

No

add date

No provided documents contain the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or test results for the spe...

Open

13736

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the 'Norms / Customer Specifications' and confirmed by the digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DM...

Open

13737

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N but not to ISO 17782 as required; no evidence provided for QTR/MPCR availability for review or full compliance with both standards for the exact product supplied. Source: DMV_STANDARD_BOO...

Open

13738

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N with wall thickness up to 31.75 mm (hot finished), and manufacturing is according to M-650 (or ISO 17782) qualified procedures, fulfilling the requirement for manufacturer and process qualification a...

Open

13739

3.1

AI

No

add date

AOD or equivalent refining is required and used for 100% of production, and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13740

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed by supplier certification and heat analysis per ASTM A790 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

13741

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is covered by compliance...

Open

13742

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

13743

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

13744

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 Rev 06 is fulfilled: tensile and CVN tests are performed in the transverse direction (longitudinal if not feasible), and hardness, corrosion, and microstructure tests are c...

Open

13745

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 as referenced in ASTM A790, and material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

13746

4.3

AI

No

add date

Charpy V-notch testing in accordance with ASTM A370 and ISO 148-1 is feasible for the specified pipe dimensions and can be performed as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03...

Open

13747

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal, and applicable sub-size re...

Open

13748

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

13749

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

13750

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

13751

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

13752

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

13753

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

13754

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10 µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD...

Open

13755

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

13756

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781 with specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requirement f...

Open

13757

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS ...

Open

13758

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

13759

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content...

Open

13760

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

13761

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

13762

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultr...

Open

13763

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not demonstrated; only ASTM A790/ASTM A999 NDE is confirmed. For OD 219.1 mm, standard NDE methods (EC, UT, hydrostatic) are not fully feasible or only available at...

Open

13764

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor that NDE is performed as standard for the requested dimension at Montbard. Source: DMV_STANDARD_...

Open

13765

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no evidence of override in the customer specification. OD, WT, and ovality tolerances for the specified dimensions are confirmed as complia...

Open

13766

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

13767

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

13768

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produc...

Open

13769

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

13770

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

13771

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

13772

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

13773

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

13774

10.2

AI

No

add date

NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and results of all required metallurgical and non-destructive testing are not fully documented. Only the country of o...

Open

13775

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, including chemical, mechanical, manufacturing, and testing requirements. M-650 qualification is confirmed f...

Open

13776

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N (up to WT = 31.75 mm) but not accredited to ISO 17782; no evidence of QTR/MPCR availability or full compliance with both NORSOK M-650/ISO 17782 as required. Source: DMV_STANDARD_BOOK/02-0...

Open

13777

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

13778

3.1

AI

No

add date

AOD or equivalent refining is standard practice and used 100% for DMV 25.7N, which also complies with the required chemical composition per Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13779

3.1

AI

No

add date

Available documents confirm PREN ≥ 40 and general grade coverage but do not provide or confirm detailed chemical composition limits for all elements as specified for S32760. Full compliance with the table cannot be validated with the provided informa...

Open

13780

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

13781

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

13782

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

13783

4.1

AI

No

add date

Test sampling for seamless pipes per ASTM A790 and NORSOK MDS D51, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled...

Open

13784

4.2

AI

No

add date

Tensile testing is performed at room temperature per NORSOK MDS D51, which refers to ASTM A790 and requires mechanical testing in accordance with ASTM A370. The material meets the specified tensile and hardness properties. Source: DMV_STANDARD_BOOK/0...

Open

13785

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

13786

4.3

AI

No

add date

Pipe wall thickness exceeds the minimum required for Charpy V-notch testing; testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02...

Open

13787

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal. The specified pipe dimensions allow...

Open

13788

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching for intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and examination in accordance ...

Open

13789

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

13790

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

13791

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

13792

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

13793

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

13794

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

13795

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

13796

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

13797

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

13798

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is fulfilled; neither ASTM G48 nor ISO 17781 are mentioned, and no test details are provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in M...

Open

13799

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements, with microstructure acceptance referenced to ISO 17781. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

13800

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

13801

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

13802

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

13803

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782, and there is no evidence of QTR/MPCR availability as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13804

3.1

AI

No

add date

UNS S32760 chemical composition matches Table 2 requirements and DMV material conforms with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest...

Open

13805

5.2

AI

No

add date

NDE is performed per ASTM A790 (hydrostatic or EC/UT per ASTM A999), but there is no explicit confirmation of compliance with the additional or stricter NDE acceptance criteria required by NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782. Plant standar...

Open

13806

5.2

AI

No

add date

No provided document confirms that NDE acceptance is based on calibration notch indications or that pipes/tubes with such indications are rejected or repaired; feasibility for required NDE is not confirmed for the specified dimension at Montbard. Sou...

Open

13807

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790) for the specified pipe size, with no deviations or special requirements from TechnipFMC indicated in the customer specification or context. Source: DMV...

Open

13808

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

13809

8.0

AI

No

add date

Marking is performed according to ASTM A790 (§14) and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Diges...

Open

13810

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

13811

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

13812

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

13813

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demonstration for th...

Open

13814

10.2

AI

No

add date

Certification includes EN 10204 type 3.1 with traceability to heat treatment, steel manufacturer, melting/refining practice, and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number; MST-Tubes is ISO 9001 certified, ensuring documentation is tra...

Open

13815

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAN...

Open

13816

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements, including Charpy V-notch testing at -466C with minimum absorbed energy values (transverse: 45 J avg/35 J single, longitudinal: 65 J avg/50 J single) and reduction factors for sub-siz...

Open

13817

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants and electrolytic etching after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/...

Open

13818

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13819

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution annealing parameters, and ...

Open

13820

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all standard and supplementary requirements, and are M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-...

Open

13821

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N with the specified wall thickness within the qualified range, and the manufacturing process is qualified per NORSOK M-650/ISO 17782 with testing per NORSOK M-630 MDS D51 rev. 6. Source: DMV_STANDARD_...

Open

13822

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13823

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and DMV material composition conforms with supplier certification and heat analysis per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02...

Open

13824

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

13825

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined by ASTM A790, with test frequency specified as '1 / lot'. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

13826

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling as specified in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

13827

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions, is fulfilled. For the ordered pipe...

Open

13828

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

13829

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

13830

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, meeting the minimum wall thickness requirements for testing. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

13831

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability is provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13832

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

13833

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates, with isolated precipitates allowed if not distributed throughout the specimen and each below 10 μm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

13834

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

13835

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

13836

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

13837

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size, so the requirement is not fully met. Sou...

Open

13838

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

13839

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impa...

Open

13840

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

13841

4.5

AI

No

add date

No direct evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or fulfilled for the requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

13842

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO ...

Open

13843

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

13844

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to level II or III in accordance with ISO 9712 or equivalent, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 ...

Open

13845

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, which are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-0...

Open

13846

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, with manufacturing process qualified to NORSOK M-650 (or ISO 17782) and meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

13847

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or fulfilled. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

13848

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled. Standard NDE methods (hydrostatic, ultrasonic, eddy current) for the requested OD (219.1 mm) are only available at extra cost or are not...

Open

13849

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor that this NDE acceptance criterion is standard or feasible for the specified pi...

Open

13850

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standards (ASTM A999), with no evidence of alternative requirements from TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-0...

Open

13851

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

13852

8.0

AI

No

add date

Marking per ASTM A790 and plant marking methods ensure mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDA...

Open

13853

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13854

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

13855

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

13856

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

13857

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products being delivered as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

13858

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference). ...

Open

13859

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or complete metallurgical and non-dest...

Open

13860

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as required for 25 Cr Duplex stainless steel seamless pipes. Manufacturing is M-650 qualified for the specified wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

13861

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13862

3.2

AI

No

add date

Heat treatment is solution annealing followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650/ISO 17782. Pipes are treated to ensure free circulation of heating and c...

Open

13863

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

13864

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing the table for test specimen sampling as outlined in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

13865

4.1

AI

No

add date

All required tests (tensile, hardness, CVN, corrosion, microstructure) are performed as specified for seamless pipes per NORSOK MDS D51 and ASTM A790, with correct test directions and locations. For the specified pipe dimensions, transverse CVN speci...

Open

13866

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with material meeting the tensile and maximum hardness properties of Table 4. Hardness testing is also performed as required. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

13867

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

13868

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible and applicable for the specified pipe dimensions (WT 18.26mm, OD 219.1mm). Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/1...

Open

13869

4.3

AI

No

add date

Impact testing at -466C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal is specified and feasible for the requested pipe dimensions; reduction factors for sub-size spec...

Open

13870

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is specified to be performed according to ISO 17781 with appropriate etchants, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

13871

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, is required for micrographic examination as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

13872

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

13873

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STANDA...

Open

13874

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

13875

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

13876

4.4.2

AI

No

add date

The available specifications allow isolated intermetallic precipitates below 10μm, while the requirement prohibits all intermetallic phases and/or precipitates if CVN testing cannot be completed. The requirement is not fully met. Source: DMV_STANDARD...

Open

13877

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

13878

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and corr...

Open

13879

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as specified in NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 R...

Open

13880

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

13881

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, with accredited manufacturing and qualification processes. Source: DMV_STANDARD_BOOK/02 - ...

Open

13882

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours is performed for DMV 25.7N, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and DMV 25.7N complies with these requirements. Source: DMV_STANDARD_B...

Open

13883

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

13884

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non des...

Open

13885

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not addressed in the available documentation. For the requested pipe size, standard NDE methods (eddy current, hydrostatic, ultrasonic) are either not feasible or o...

Open

13886

5.2

AI

No

add date

No provided documentation explicitly states that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor confirms NDE acceptance criteria based on calibration notches for the specif...

Open

13887

6.0

AI

No

add date

Dimensional tolerances are confirmed as per the applicable ASTM standard (ASTM A790 referencing ASTM A999) for the specified dimensions, with no alternative requirements stated by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc,...

Open

13888

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be pickled or bright annealed, fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.do...

Open

13889

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

13890

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13891

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03...

Open

13892

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

13893

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

13894

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demons...

Open

13895

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to delivered products, fulfilling the requirement for documentation to be transmitted to TechnipFMC and traceable as per SIR205. Source: DMV_STANDARD_BOOK/0...

Open

13896

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications and plant certification procedures. Source: DMV_STANDARD_BOOK/02-...

Open

13897

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice and refining method, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the actual steel produce...

Open

13898

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all referenced mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STA...

Open

13899

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; full qualification to NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR is not confirmed. Source: DMV_STANDARD_BOOK/02-04...

Open

13900

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

13901

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13902

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the requirement table and is confirmed to conform to ASTM A790 Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 79...

Open

13903

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

13904

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

13905

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and per 100 pieces, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

13906

4.1

AI

No

add date

DMV 25.7N seamless pipes are tested per NORSOK MDS D51/ASTM A790 requirements: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure, with correct locations and directions. Fo...

Open

13907

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with tensile and hardness properties meeting Table 4 requirements for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13908

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

13909

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, meeting the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 -...

Open

13910

4.3

AI

No

add date

Charpy V-notch impact properties at -46°C (transverse: average ≥45 J, single ≥35 J; longitudinal: average ≥65 J, single ≥50 J; reduction factors for sub-size specimens) are fully met for wall thickness >6mm, as specified for DMV 25.7N and confirmed f...

Open

13911

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified electrolytic etchant after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

13912

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases is required, in accordance with ISO 17781 Appendix B, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

13913

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

13914

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

13915

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report at actual magnification and with a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/...

Open

13916

4.4.2

AI

No

add date

Findings of intermetallic stringers must be reported, and acceptance is based on CVN and corrosion test results, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

13917

4.4.2

AI

No

add date

No provided documentation fully prohibits intermetallic phases and/or precipitates when CVN testing cannot be completed; the referenced digest allows isolated precipitates below 10µm, which does not meet the requirement for total prohibition in this ...

Open

13918

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

13919

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requirement for DMV 25....

Open

13920

4.4.3

AI

No

add date

Ferrite content of 35% to 60% is required and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13921

4.5

AI

No

add date

No direct evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or planned; relevant standards are referenced but not explicitly confirmed for this requirement. Source: DMV_STANDARD_BOOK/12-03-0...

Open

13922

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

13923

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, meeting the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest...

Open

13924

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to level II or III in accordance with ISO 9712 or equivalent, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 ...

Open

13925

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the requested pipe dimensions are within machine capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ul...

Open

13926

5.2

AI

No

add date

No evidence that NDE acceptance criteria per ASTM A790, NORSOK M-630 MDS D51 Rev 6, or NORSOK M-650/ISO 17782 are fulfilled. Standard NDE methods (UT, EC, hydrostatic) are not confirmed as feasible or available for the specified pipe size at Montbard...

Open

13927

5.2

AI

No

add date

None of the provided documents confirm that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor do they specify the required acceptance criteria for NDE as per the requirement. ...

Open

13928

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790) unless otherwise specified, with no overriding customer requirements identified. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDAR...

Open

13929

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

13930

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number, lot number, and other traceability information, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06....

Open

13931

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Diges...

Open

13932

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

13933

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

13934

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the size and p...

Open

13935

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13936

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

13937

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control for mill inspection as specified. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

13938

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and full test results are not fully provided. Only the co...

Open

13939

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, as specified. The product is 25 Cr Duplex stainless steel seamless pipe, and compliance is confirmed for ch...

Open

13940

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability or full compliance with both standards as required by the specification. Source: DMV_STANDARD_BOOK/02 -...

Open

13941

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N, with manufacturing processes qualified per M-650 or ISO 17782 and qualification testing meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

13942

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13943

3.1

AI

No

add date

Chemical composition for UNS S32760 conforms to Table 2 of ASTM A790, matching the specified limits, with heat analysis and supplier certification provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-0...

Open

13944

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and furnace accreditation is confirmed for DMV 25.7N. Free circulation of heating/cooling media is en...

Open

13945

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

13946

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

13947

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests, with specified locations and directions, is fulfilled for DMV 25.7N per ...

Open

13948

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370, with mechanical properties and maximum hardness meeting Table 4 requirements for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

13949

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW, fulfilling the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

13950

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

13951

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal, and the specified pipe dimensions allow required testing to be pe...

Open

13952

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH solution after final polishing, fulfilling the requirement for metallographic preparation and examin...

Open

13953

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution for detecting ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

13954

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

13955

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

13956

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

13957

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

13958

4.4.2

AI

No

add date

No provided documentation explicitly prohibits all intermetallic phases and/or precipitates when CVN testing cannot be completed; isolated precipitates are still allowed under current specifications, which does not meet the stricter client requiremen...

Open

13959

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

13960

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 at ≥400X magnification, etching to detect intermetallic phases, nitrides, and carbides. Acceptance: structure must be basically free from intermetallic precipitates (isolated precipitates <10µm al...

Open

13961

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13962

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or confirmed in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

13963

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

13964

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, meeting the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest...

Open

13965

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

13966

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testin...

Open

13967

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782 requirements are addressed. For OD 219.1 mm, eddy current testing is not feasible, and hydrostatic or ultrasonic testing is only availa...

Open

13968

5.2

AI

No

add date

No provided documentation explicitly states that any indication greater than the calibration notch is considered a defect requiring rejection or repair, and standard NDE methods for this OD are not feasible at Montbard for eddy current testing. Sourc...

Open

13969

6.0

AI

No

add date

Dimensional tolerances are specified as per ASTM A790 and ASTM A999 for seamless pipe, with no deviations or special tolerances indicated in the customer request, fulfilling the requirement that tolerances follow the applicable ASTM standard unless o...

Open

13970

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

13971

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

13972

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

13973

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

13974

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified ...

Open

13975

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

13976

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and validated by Quality Control, and will include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-65...

Open

13977

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all required metallurgic...

Open

13978

1.0

AI

No

add date

DMV 25.7N is specified as the grade, with compliance to ASTM A790 and NORSOK M-630 MDS D51 rev. 6 confirmed, including M-650 qualification and fulfillment of all mechanical, chemical, and testing requirements for seamless pipes. Source: DMV_STANDARD_...

Open

13979

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of full qualification to both NORSOK M-650/ISO 17782 or availability of QTR/MPCR for review as required by the specification. So...

Open

13980

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

13981

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

13982

3.1

AI

No

add date

DMV 25.7N (UNS S32760) chemical composition matches the specified limits, including PREN ≥ 40, and compliance is confirmed for the grade per ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D...

Open

13983

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

13984

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

13985

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ...

Open

13986

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, longitudinal if not possible), and corrosion/microstructure tests are performed at the specif...

Open

13987

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

13988

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW, fulfilling Table 4 mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

13989

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

13990

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements, including Charpy V-notch testing at -466C with minimum absorbed energy values (transverse: 45 J average, 35 J single; longitudinal: 65 J average, 50 J single if transverse not possib...

Open

13991

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

13992

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is specified and fulfills the requirement for suitable etchant(s) as listed in ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

13993

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

13994

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

13995

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

13996

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

13997

4.4.2

AI

No

add date

No source fully prohibits intermetallic phases and/or precipitates when CVN testing cannot be completed; the closest allows isolated precipitates below 10μm, which does not meet the zero-tolerance requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Dig...

Open

13998

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 ...

Open

13999

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

14000

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

14001

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 (ASTM A790, NORSOK M-630, M-650/ISO 17782) are fully met, including compliance for destructive and microstructural tests (tensile, impact, corrosion, microstructure, ferrite). ...

Open

14002

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

14003

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montb...

Open

14004

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is confirmed for the specified pipe dimensions, and compliance with ASTM E213 implies calibration notch requirements are met as part of standard practice. Source: DMV_STANDARD_BOOK/12 -...

Open

14005

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT) is detailed, but there is no explicit confirmation of compliance with NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782 NDE requirements. For OD 219.1 mm, eddy current testing is not feasible, and hydrosta...

Open

14006

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect and that defective pipe and tubing shall be rejected or repaired; NDE acceptance criteria and required testing are...

Open

14007

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a A ...

Open

14008

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14009

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

14010

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

14011

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

14012

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, fulfilling the qualification requirement for the specified size and product f...

Open

14013

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to the products, fulfilling the requirement for documentation to be transmitted to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

14014

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

14015

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and n...

Open

14016

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

14017

1.0

AI

No

add date

Supplier is NORSOK M-650 accredited for UNS S32760 / DMV25.7N but not accredited to ISO 17782 as required; no evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14018

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

14019

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14020

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed by supplier certification and heat analysis per ASTM A790 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

14021

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

14022

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

14023

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

14024

4.1

AI

No

add date

All required tests (tensile, hardness, CVN, corrosion, microstructure) are performed on seamless pipes per NORSOK MDS D51 and ASTM A790, with correct test directions and thickness locations. For the specified pipe dimensions, transverse CVN specimens...

Open

14025

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

14026

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

14027

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe size and wall thickness; both standards are referenced for this application. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/...

Open

14028

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements, including Charpy V-notch testing at -46°C with minimum energy values (transverse: 45 J avg/35 J single, longitudinal: 65 J avg/50 J single) and sub-size reduction factors; the specifi...

Open

14029

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

14030

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

14031

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

14032

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

14033

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

14034

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 requires reporting of intermetallic phases, with acceptance based on CVN and corrosion test results if such phases are present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STAN...

Open

14035

4.4.2

AI

No

add date

The available documents do not confirm that intermetallic phases and/or precipitates are completely prohibited if CVN testing cannot be completed; isolated precipitates are allowed under certain conditions, which does not meet the stricter client req...

Open

14036

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

14037

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

14038

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

14039

4.5

AI

No

add date

No direct evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or fulfilled. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

14040

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements, as well as manufacturing, heat treatment, and qualification requirements. Source: DMV_STA...

Open

14041

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

14042

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

14043

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects is performed in accordance with ASTM E213 or ISO 10893-10 for the required pipe dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 ...

Open

14044

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT) is confirmed, but compliance with specific NDE requirements of NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782 is not demonstrated. For the requested OD, eddy current testing is not feasible, and hydrost...

Open

14045

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect and that defective pipe and tubing shall be rejected or repaired, as required by the specification. NDE acceptance...

Open

14046

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no deviations or special tolerances specified by the customer or TechnipFMC. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - Ge...

Open

14047

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be pickled or bright annealed, fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14048

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 §14, requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring compliance with the requirement for traceability...

Open

14049

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

14050

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

14051

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification de...

Open

14052

10.2

AI

No

add date

Certification includes EN 10204 type 3.1 with traceability to heat treatment, steel manufacturer, melting/refining practice, and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, fulfilling the requirement for documentation traceable to the ...

Open

14053

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications and plant documentation. Source: DMV_STANDARD_BOOK/02-04-03 - Dig...

Open

14054

10.2

AI

No

add date

Most required documentation and certification details (NORSOK M-650/ISO 17782 identification, steel melting practice, heat number, chemical analysis, solution annealing details, metallurgical and NDT results) are stated to be included in the EN 10204...

Open

14055

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the item table and confirmed by the referenced specification digest. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14056

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782, and there is no confirmation of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Dige...

Open

14057

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

14058

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14059

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits and PREN requirements specified in Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 6 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev...

Open

14060

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

14061

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

14062

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ...

Open

14063

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

14064

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests, with specified locations and directions, is fulfilled for DMV 25.7N per...

Open

14065

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, with material meeting the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

14066

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spe...

Open

14067

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 and ISO 148-1 is feasible for the specified pipe dimensions and can be performed as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact te...

Open

14068

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C, minimum absorbed energies of 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal, with sub-size reducti...

Open

14069

4.4.1

AI

No

add date

Micrographic examination and ferrite check are performed as per ISO 17781, and etching methods are described, but the exact etchant solution required for detecting intermetallic phases and ferrite balance electrolytic etching after final polishing is...

Open

14070

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

14071

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

14072

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

14073

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

14074

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

14075

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates, which does not meet the stricter client requirement of not permitting any i...

Open

14076

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

14077

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

14078

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

14079

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified per NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

14080

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, meeting the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest...

Open

14081

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

14082

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed on the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

14083

5.2

AI

No

add date

NDE per ASTM A790 is generally feasible, but NORSOK M-630 MDS D51/NORSOK M-650/ISO 17782-specific NDE acceptance criteria are not confirmed. For the requested OD (219.1 mm), Eddy current testing is not feasible, and hydrostatic/ultrasonic tests are o...

Open

14084

5.2

AI

No

add date

No provided document explicitly states that any indication greater than that produced by the calibration notch represents a defect, nor confirms the rejection or repair of such defective pipe and tubing as required. NDE acceptance criteria based on c...

Open

14085

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790) for the specified pipe dimensions, with no overriding requirements from TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STAN...

Open

14086

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14087

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and standard practice at Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_S...

Open

14088

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

14089

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

14090

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

14091

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling supplier qualification documentation requirem...

Open

14092

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

14093

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary or QTR n...

Open

14094

10.2

AI

No

add date

Most required documentation and certification details (NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel melting practice and refining method, heat number, chemical analysis, solution annealing parameters, and test results) are stated a...

Open

14095

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all chemical, mechanical, manufacturing, and testing requirements, and are M-650 qualified up to the required wall thickness for 25 Cr Duplex stain...

Open

14096

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782, which is explicitly required. No confirmation of QTR/MPCR availability for review is provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14097

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

14098

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard and required for 100% of production, and the chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK...

Open

14099

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition requirements, including PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat to ensure conformity with the requir...

Open

14100

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is covered by compliance...

Open

14101

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

14102

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

14103

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled per NORSOK MDS D51/ASTM A790. Th...

Open

14104

4.2

AI

No

add date

Tensile testing is performed per ASTM A370/ISO 6892-1 and meets the required properties; hardness testing is also performed and results are provided, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

14105

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

14106

4.3

AI

No

add date

Charpy V-notch testing is feasible and meets ASTM A370 and ISO 148-1 requirements for the specified pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in Montbar...

Open

14107

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

14108

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energy values for transverse and longitudinal directions, and the specified pipe dimensions allow for required testing directions and specimen ...

Open

14109

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

14110

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

14111

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

14112

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

14113

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

14114

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 requires reporting of intermetallic phases, with acceptance based on CVN and corrosion test results if such phases are present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STAN...

Open

14115

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

14116

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 ...

Open

14117

4.4.3

AI

No

add date

Microstructure examination per ISO 17781 is specified, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requirement for...

Open

14118

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies within this range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NOR...

Open

14119

4.5

AI

No

add date

No explicit evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or planned. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

14120

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORS...

Open

14121

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

14122

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destruct...

Open

14123

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/1...

Open

14124

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed; standard NDE methods (hydrostatic, ultrasonic, eddy current) are not fully feasible for the requested OD at Montbard without extra cost or technical consul...

Open

14125

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor is there confirmation that the required NDE will be performed as standard for t...

Open

14126

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) as required, with no deviations specified by TechnipFMC in the provided context. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tole...

Open

14127

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14128

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

14129

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14130

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

14131

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

14132

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

14133

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products as required by SIR205 and section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

14134

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specification sections. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D...

Open

14135

10.2

AI

No

add date

Most required documentation and certification details (NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and test results) are either missing or only generally describ...

Open

14136

1.0

AI

No

add date

DMV 25.7N seamless pipes are 25 Cr Duplex stainless steel, manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with all standard and supplementary requirements met, and M-650 qualification confirmed for the required wall t...

Open

14137

3.1

AI

No

add date

DMV 25.7N (UNS S32760) chemical composition matches the requirement table and complies with ASTM A790 and NORSOK MDS D51 Rev 06, including PREN ≥ 40 and all specified element limits. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK...

Open

14138

1.0

AI

No

add date

No evidence is provided that the supplier is qualified to both NORSOK M-650 and ISO 17782, nor that Qualification Test Records/Manufacturer Procedure Conformity Records (QTR/MPCR) are available for review as required by the specification. The supplie...

Open

14139

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

14140

3.1

AI

No

add date

AOD or equivalent refining is standard practice and required for 100% of production, and DMV 25.7N complies with the specified chemical composition requirements. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14141

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition requirements and PRE ≥ 40 as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03...

Open

14142

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

14143

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790 for DMV 25.7N, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

14144

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling as outlined in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

14145

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled per NORSOK MDS D51/ASTM A790. Fo...

Open

14146

4.2

AI

No

add date

Tensile testing is performed per ASTM A370/ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4. Hardness testing is also performed as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

14147

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: yield strength ≥ 550 MPa, tensile strength ≥ 750 MPa, elongation ≥ 25%, and hardness max 310 HBW/32 HRC, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

14148

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, meeting the minimum wall thickness requirements for testing. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

14149

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C (transverse: 45/35 J, longitudinal: 65/50 J) for thickness >6mm, and the specified pipe dimensions allow for required testing directions. Source: DMV_STANDARD_BOOK/02-...

Open

14150

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

14151

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution for detecting ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

14152

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14153

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

14154

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

14155

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

14156

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

14157

4.4.2

AI

No

add date

No provided documentation confirms a zero-tolerance policy for intermetallic phases and/or precipitates when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10 µm, which does not meet the stricter client requ...

Open

14158

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

14159

4.4.3

AI

No

add date

Microstructure examination is performed as per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at minimum 400X magnification. Acceptance criteria require the structure to be basically free from intermetallic precipitates...

Open

14160

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

14161

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

14162

4.5

AI

No

add date

DMV 25.7N meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, including destructive, micrographic, corrosion tests, ferrite content, heat treatment, and manufacturing process requirements. Source: DMV_STANDARD_BOOK/02-04-03...

Open

14163

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

14164

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

14165

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within capability range. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02...

Open

14166

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled; only ASTM A790/A999 NDE is detailed, and standard NDE methods (EC, UT, hydrostatic) are not fully feasible for the specified pipe size at Mont...

Open

14167

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

14168

5.2

AI

No

add date

No explicit evidence that indications greater than the calibration notch are treated as defects requiring rejection or repair; standard NDE method (Eddy current) is not feasible for the requested OD at Montbard, so compliance with the requirement can...

Open

14169

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding TechnipFMC specification indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a A 376-0...

Open

14170

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14171

8.0

AI

No

add date

Marking is performed per ASTM A790 §14 and includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-0...

Open

14172

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' in the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

14173

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

14174

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

14175

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

14176

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

14177

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 manufacturing summary/QTR number. Source: DMV_ST...

Open

14178

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice and refining method, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel produ...

Open

14179

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with all required tests, certifications, and M-650 qualification covered for the specified wall thickness and grade. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

14180

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not to ISO 17782, as explicitly required. No evidence of QTR/MPCR availability is provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14181

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to M-650 or ISO 17782, meeting the requirement for manufacturer and process qualification with testing per NORS...

Open

14182

3.1

AI

No

add date

AOD or equivalent refining is used for DMV 25.7N, and chemical analysis complies with Table 2 of ASTM A790 and NORSOK MDS D51 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14183

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

14184

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for one set per heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

14185

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

14186

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled for DMV 25.7N as p...

Open

14187

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 as required, with material meeting the specified tensile and maximum hardness properties. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

14188

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and maximum hardness 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spe...

Open

14189

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, meeting the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 -...

Open

14190

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal, and the specified pipe dimensions allow for required transverse t...

Open

14191

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

14192

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination of the material, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

14193

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

14194

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

14195

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

14196

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 requires reporting of intermetallic stringers, with acceptance based on CVN and corrosion test results as specified in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spe...

Open

14197

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fulfilled. Source: DMV_STANDARD_...

Open

14198

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

14199

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Acceptance criteria require the structure to be basically free from intermetallic precipitates, with iso...

Open

14200

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14201

4.5

AI

No

add date

No direct evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or confirmed for the requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

14202

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO ...

Open

14203

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

14204

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destruct...

Open

14205

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 and ISO 10893-10 is available, including reference notches as per ASTM E213. Pipe dimensions are within capability range. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

14206

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/ISO 17782 are not fully addressed. For OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic testing is only available at extra cost and not standard. Full-length ...

Open

14207

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair; the specific NDE acceptance criterion is not explicitly stated or confirmed for the requested pro...

Open

14208

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790/A999) for the requested pipe, with no evidence of override by TechnipFMC specifications or drawings. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV...

Open

14209

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and white pickled or bright annealed according to NORSOK MDS D51 Rev 06, fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: Digest A...

Open

14210

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

14211

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

14212

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system certified within the EEA and specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

14213

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification de...

Open

14214

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

14215

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and validated for mill inspection, and will include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-6...

Open

14216

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis (ladle), solution annealing temperature/ho...

Open

14217

1.0

AI

No

add date

25 Cr Duplex stainless steel seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, meeting all specified chemical, mechanical, manufacturing, testing, and qualification requirements. Source: DMV_STANDARD_B...

Open

14218

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782, and there is no confirmation of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Dige...

Open

14219

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

14220

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard and required for 100% of production, and chemical analysis complies with Table 2 for DMV 25.7N seamless pipe as per ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04...

Open

14221

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790 as required, with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 7...

Open

14222

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650/ISO 17782. Free circulation of heating/cooling media is ensured by compliance wit...

Open

14223

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

14224

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling as outlined in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

14225

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled per NORSOK MDS D51/ASTM A790. Fo...

Open

14226

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370, with required properties (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and maximum hardness confirmed. DMV 25.7N is compliant with these requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

14227

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW, fulfilling Table 4 mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

14228

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfilled for the specified pipe dimensions, meeting ASTM A370 and ISO 148-1 requirements for minimum wall thickness. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact ...

Open

14229

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal, and the specified pipe dimensions allow for required testing dir...

Open

14230

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

14231

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

14232

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

14233

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

14234

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report at actual magnification and with a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

14235

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

14236

4.4.2

AI

No

add date

The available documents do not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed; isolated precipitates are allowed under certain conditions, which does not meet the stricter client requirement that none are p...

Open

14237

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

14238

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impa...

Open

14239

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

14240

4.5

AI

No

add date

There is no explicit evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 will be performed or has been performed for this requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant....

Open

14241

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14242

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

14243

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

14244

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - ...

Open

14245

5.2

AI

No

add date

NDE per ASTM A790 is covered, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the specified OD, eddy current testing is not feasible, and hydrostatic/ultrasonic ...

Open

14246

5.2

AI

No

add date

No referenced standard or plant process explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair; NDE methods are not standard or feasible for the requested size at the plant. Sou...

Open

14247

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790) unless otherwise specified, and no overriding TechnipFMC requirement is indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STAND...

Open

14248

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14249

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

14250

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Diges...

Open

14251

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

14252

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

14253

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782; no evidence of QTR/MPCR availability as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14254

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified ...

Open

14255

10.2

AI

No

add date

MST-Tubes is ISO 9001 certified and provides EN 10204 type 3.1 certificates with traceability to delivered products, fulfilling the documentation and traceability requirement for TechnipFMC as specified in SIR205. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

14256

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

14257

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, actual chemical analysis results, solution annealing parameter...

Open

14258

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured and tested in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, meeting all relevant mechanical, chemical, and testing specifications for 25 Cr Duplex stainless...

Open

14259

1.0

AI

No

add date

No evidence that the supplier is qualified in accordance with both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of the availability of the full Qualification Test Record/Manufacturer Procedure Conformity Records for rev...

Open

14260

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 (or ISO 17782), fulfilling the requirement for manufacturer and process qualification and meeting NORSO...

Open

14261

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N meets the chemical composition requirements of Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

14262

3.1

AI

No

add date

DMV 25.7N (UNS S32760) is manufactured according to NORSOK M-650 qualification, with MST-Tubes F accredited for UNS S32760/DMV25.7N up to WT = 31.75 mm, covering the requested WT of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

14263

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is qualified to NORSOK M-650/ISO 17782, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is covered by complian...

Open

14264

4.1

AI

No

add date

No evidence that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790. Testing frequency, lot definition, and full compliance with the requi...

Open

14265

4.1

AI

No

add date

Test sampling details such as test direction for tensile and CVN, and the required sampling locations, are not fully specified. There is no explicit confirmation of CVN impact testing, its direction, or sampling location, nor of corrosion or microstr...

Open

14266

4.2

AI

No

add date

Tensile testing is performed in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 ...

Open

14267

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required in Table 4 are not explicitly confirmed for DMV 25.7N; standard references and test mentions do not validate fulfillment of specified minimums for this grade...

Open

14268

4.3

AI

No

add date

No evidence that Charpy V-notch testing is performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1, or that results meet Table 5 requirements for the specified product and order context. Source: DMV_STANDARD_BOOK/02-02-01 Digest summary of A...

Open

14269

4.3

AI

No

add date

Impact testing at -46°C with specified absorbed energy values is feasible and can be fulfilled for pipe with 18.26mm wall thickness, as both ASTM and ISO rules confirm transverse specimens are possible for this size. Source: DMV_STANDARD_BOOK/12 - Sp...

Open

14270

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination per ISO 17781 or use of the specified etchant for 25 Cr Duplex stainless steels. Grain size examination procedures provided are not applicable to duplex grades and do not reference ISO 17781 o...

Open

14271

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination of ferrite balance and intermetallic phases is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - De...

Open

14272

4.4.2

AI

No

add date

The microstructure must be basically free from intermetallic precipitates, with isolated precipitates allowed if not distributed throughout the specimen and each below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

14273

4.4.2

AI

No

add date

No evidence of detection, recording, or micrographic documentation (400x minimum) of intermetallic phases is provided or addressed in the relevant documentation or comments. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/1...

Open

14274

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with representative micrographs at or near mid-wall thickness, actual magnification, and a scale bar included if intermetallic phases are not detected. Source: DMV_STANDARD_BOO...

Open

14275

4.4.2

AI

No

add date

No relevant documents address the presence, reporting, or acceptance criteria for centerline intermetallic stringers, nor do they specify acceptance based on CVN and corrosion test results if such stringers are present. Source: DMV_STANDARD_BOOK/12-0...

Open

14276

4.4.2

AI

No

add date

NORSOK MDS D41 Rev 06 and D51 Rev 06 allow isolated intermetallic precipitates below 10µm even if CVN testing cannot be completed, which does not fully prohibit intermetallic phases/precipitates as required by the client. No other relevant documents ...

Open

14277

4.4.3

AI

No

add date

No evidence of ferrite content determination by ASTM E 562 or ASTM E 1245 in accordance with ISO 17781; only grain size measurement is addressed, not ferrite content or required methods for this requirement. Source: DMV_STANDARD_BOOK/12 - Special Tes...

Open

14278

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with all relevant mechanical, chemical, and testing requirements met, and M-650 qualification confirmed for the specified wall thickness. Source: DMV_STANDAR...

Open

14279

4.4.3

AI

No

add date

No provided document specifies acceptance criteria for micrographic examination or metallurgical properties as required in section 4.4 of the client specification. Procedures and standards are mentioned, but no actual acceptance criteria are given fo...

Open

14280

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14281

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided in the available documentation or specifications. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

14282

4.5

AI

No

add date

No specific acceptance criteria are provided for metallurgical properties, so fulfillment cannot be determined. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.do...

Open

14283

4.5

AI

No

add date

Pitting corrosion test per ISO 17781, G48 Method A at 25°C for 24 hours is required, with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the client's requirements. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

14284

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDA...

Open

14285

5.2

AI

No

add date

No explicit confirmation of 100% ultrasonic testing per ASTM E213 or ISO 10893-10, including reference notch requirements and timing after all processing, is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-...

Open

14286

5.2

AI

No

add date

100% qualitative anti-mixing PMI check is performed on standard production at Montbard using appropriate instruments, fulfilling the general NDE requirement for positive material identification. Source: DMV_STANDARD_BOOK/12-06-06 - Positive Material ...

Open

14287

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair; NDE acceptance criteria are not specified for the requested product and dimension at Montbard....

Open

14288

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed as per the applicable ASTM standards (including ASTM A790/A999) for the relevant product dimensions, with no deviations or exceptions noted and no overriding TechnipFMC part report or drawi...

Open

14289

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and NORSOK MDS S01, directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790, NORSOK MDS S01.

Open

14290

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

14291

10.0

AI

No

add date

No evidence of an ISO 9001 (or equivalent) quality-assurance system certified by a competent EEA body with specific assessment for materials is provided in the available documentation. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_ST...

Open

14292

10.1

AI

No

add date

No confirmation that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification M...

Open

14293

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number as required. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

14294

10.2

AI

No

add date

No evidence that documentation traceable to the products and to be transmitted to TechnipFMC as required by SIR205 will be provided; no explicit statement or process confirming fulfillment of this requirement for the specific order or customer tracea...

Open

14295

10.2

AI

No

add date

Material certificate is issued according to EN 10204 Type 3.1 and validated by Quality Control for mill inspection, which fulfills the requirement for certification type and standard practice for inclusion of ASTM A790 and NORSOK M-630 information fo...

Open

14296

10.2

AI

No

add date

None of the provided documents contain the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or test results as...

Open

14297

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/...

Open

14298

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782; full compliance with both NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR is not confirmed. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 R...

Open

14299

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N (UNS S32760) up to 31.75 mm WT, and the required WT is 18.26 mm. The manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Sourc...

Open

14300

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14301

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSO...

Open

14302

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnace qualification per NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensu...

Open

14303

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

14304

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, directly referencing the required table for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - De...

Open

14305

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests, with specified locations and directions, is fulfilled for DMV 25.7N per ...

Open

14306

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370, with mechanical properties meeting NORSOK MDS D51 Table 4 (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%), and hardness testing is also performed as required. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

14307

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 06 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14308

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and meets the standard requirements for wall thickness. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

14309

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements: Charpy V-notch testing at -466C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal if transverse is not possi...

Open

14310

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

14311

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

14312

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

14313

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

14314

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

14315

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria based on CVN and corrosion...

Open

14316

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

14317

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 ...

Open

14318

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

14319

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

14320

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

14321

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including chemical composition, PRE, tensile, impact, corrosion, microstructure, and ferrite content requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

14322

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 24h, 50°C) is performed with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², which DMV 25.7N grade complies with. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

14323

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

14324

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed on the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - U...

Open

14325

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not demonstrated; only ASTM A790/A999 NDE is referenced, and for the specified OD, standard NDE methods are either not feasible or only available at extra cost. No eviden...

Open

14326

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor that this NDE acceptance criterion is standardly applied or feasible for the requested pipe dime...

Open

14327

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a A...

Open

14328

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14329

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 (§14), requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring compliance with the requirement. Source: DMV_S...

Open

14330

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14331

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

14332

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

14333

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number as required, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

14334

10.2

AI

No

add date

Certification includes EN 10204 type 3.1 with traceability to heat treatment, steel manufacturer, melting/refining practice, and NORSOK M-650/ISO 17782 qualification summary or QTR number; MST-Tubes is ISO 9001 certified. Source: DMV_STANDARD_BOOK/02...

Open

14335

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14336

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant standards and qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest ...

Open

14337

10.2

AI

No

add date

No provided documentation includes all required details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, actual chemical analysis, solution annealing parameters, or results of all metallurgical and non-des...

Open

14338

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with all standard and supplementary requirements recognized and met. M-650 qualification is confirmed for the required wall thickness. Source...

Open

14339

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

14340

3.1

AI

No

add date

AOD or equivalent refining is used for DMV 25.7N, and chemical analysis complies with Table 2 requirements for ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14341

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and DMV material composition conforms with supplier certification and heat analysis per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02...

Open

14342

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

14343

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for one set per heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

14344

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and per 100 pieces, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

14345

4.1

AI

No

add date

Destructive tests (tensile, hardness, CVN, corrosion, microstructure) are performed on prolongation samples for seamless pipes per ASTM A790 and NORSOK MDS D51 Rev 06, with tensile and CVN tests in the transverse direction (longitudinal if not feasib...

Open

14346

4.2

AI

No

add date

Tensile testing is performed at room temperature per required standards, with mechanical properties and hardness requirements matching Table 4. Compliance with ASTM A370 or ISO 6892-1 and NORSOK MDS D51 is confirmed. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

14347

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

14348

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfills the requirement as the pipe wall thickness exceeds the minimum required by ASTM and ISO standards for such testing. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

14349

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact test requirements (Charpy V-notch at -46°C, minimum values: transverse 45J/35J, longitudinal 65J/50J, sub-size reduction factors). The specified pipe dimensions allow for required impact testing di...

Open

14350

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified electrolytic etchant after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

14351

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

14352

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

14353

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

14354

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report at actual magnification and with a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

14355

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_ST...

Open

14356

4.4.2

AI

No

add date

No evidence that intermetallic phases and/or precipitates are fully prohibited when CVN testing cannot be completed; allowance for isolated precipitates does not meet the requirement for total prohibition in this case. Source: DMV_STANDARD_BOOK/02-03...

Open

14357

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

14358

4.4.3

AI

No

add date

Microstructure examination per ISO 17781 is specified, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impac...

Open

14359

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

14360

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided; compliance cannot be confirmed based on the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montba...

Open

14361

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 are fulfilled, including compliance with destructive and micrographic tests, PRE, tensile, impact, corrosion, microstructure, ferrite content, manufacturing, heat treatment, an...

Open

14362

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, meeting the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest...

Open

14363

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montb...

Open

14364

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is performed on the required dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

14365

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790/NORSOK M-630 MDS D51 are not fully addressed; only standard hydrostatic or electric testing per ASTM A999 is confirmed, and for the required OD (219.1 mm), eddy current and ultrasonic testing are only available a...

Open

14366

5.2

AI

No

add date

None of the referenced documents explicitly state that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, nor do they confirm that NDE with this acceptance criterion is performed as s...

Open

14367

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the requested pipe, with no overriding specification from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - T...

Open

14368

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 (6.1.3) and NORSOK MDS D51 Rev 06 (§13), directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: Digest ASTM A 790.docx, Digest ...

Open

14369

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures ensures mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

14370

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

14371

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

14372

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body established within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

14373

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

14374

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products as required by SIR205 and section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

14375

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification summary. Source: DMV_STANDARD_BOOK...

Open

14376

10.2

AI

No

add date

No provided documentation includes all required details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all metallurgical...

Open

14377

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' or compliance with ISO 17781 is provided for the requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

14378

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 or availability of Qualification Test Records (QTR/MPCR) is provided. Accreditation is only confirmed for NORSOK M-650, not ISO 17782, as required by the specification. Source: ...

Open

14379

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

14380

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14381

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

14382

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

14383

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

14384

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

14385

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), corrosion, and microstructure tests at specified thickness locations per NORSOK MDS D51/ASTM A790. F...

Open

14386

4.2

AI

No

add date

Tensile testing is performed at room temperature per required standards, with mechanical properties and hardness requirements matching Table 4, and compliance with ASTM A370 or ISO 6892-1 is confirmed. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

14387

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

14388

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness (>6mm), fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - ...

Open

14389

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements, including Charpy V-notch testing at -46°C with minimum absorbed energy values (transverse: 45 J average/35 J single; longitudinal: 65 J average/50 J single if transverse not p...

Open

14390

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed according to ISO 17781 with 20-40% NaOH or KOH solution after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

14391

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

14392

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

14393

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

14394

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included at actual magnification and a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

14395

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 includes detection and reporting of intermetallic phases, with acceptance based on CVN and corrosion test results as required for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

14396

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size. No other relevant information provided support...

Open

14397

4.4.3

AI

No

add date

Ferrite content is checked per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

14398

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

14399

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

14400

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the referenced documentation or specifications. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

14401

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 06 are fully met, including compliance for destructive and micrographic tests, tensile, impact, corrosion, ferrite, microstructure, solution annealing, ferrite range, absence of ...

Open

14402

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 24h, 50°C) is performed with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m²; DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

14403

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

14404

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within machine capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testi...

Open

14405

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630/MDS D51 are not confirmed as fulfilled. Provided documents either do not address NDE methods/criteria, do not cover the required grade/specification, or indicate that required NDE methods (eddy c...

Open

14406

5.2

AI

No

add date

No provided documentation explicitly confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor that the required NDE with this acceptance criterion will be performed as standard for the ...

Open

14407

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A ...

Open

14408

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14409

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790, ensuring full traceability to melt and heat treatment lot. Marking methods include heat number and DMV lot number, fulfilling the traceability requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Dig...

Open

14410

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' (§ 13, § 14) for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

14411

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

14412

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body as per the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

14413

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size ...

Open

14414

10.2

AI

No

add date

Certification includes EN 10204 type 3.1 with traceability to heat treatment, steel manufacturer, melting/refining practice, and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number; MST-Tubes is ISO 9001 certified. Source: DMV_STANDARD_BOOK/02 ...

Open

14415

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAN...

Open

14416

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. Other required ...

Open

14417

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, meeting all chemical, mechanical, manufacturing, and testing requirements, with M-650 qualification for the specified grade and wall thicknes...

Open

14418

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782, and there is no confirmation of QTR/MPCR availability as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

14419

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

14420

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14421

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and DMV material composition conforms with supplier certification and heat analysis per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed diges...

Open

14422

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

14423

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

14424

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

14425

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specifi...

Open

14426

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the specified tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

14427

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

14428

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and can be performed in accordance with ASTM A370, ASTM A1058, or ISO 148-1 as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact...

Open

14429

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements, including Charpy V-notch testing at -46°C with minimum absorbed energy values (transverse: 45 J average, 35 J single; longitudinal: 65 J average, 50 J single if transverse not...

Open

14430

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

14431

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

14432

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

14433

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

14434

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, reported at actual magnification and including a scale bar, if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - ...

Open

14435

4.4.2

AI

No

add date

Findings of intermetallic stringers must be reported, and acceptance is based on CVN and corrosion test results as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

14436

4.4.2

AI

No

add date

The referenced documents do not fully prohibit intermetallic phases and/or precipitates when CVN testing cannot be completed; isolated precipitates below 10μm are allowed, which does not meet the stricter client requirement of no intermetallics or pr...

Open

14437

4.4.3

AI

No

add date

Ferrite content is checked per ISO 17781 using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

14438

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

14439

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% as per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

14440

4.5

AI

No

add date

ASTM G48 Method 'A' corrosion testing at 50°C for 24h in accordance with ISO 17781 is not explicitly mentioned or referenced; compliance cannot be confirmed based on the available information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Mo...

Open

14441

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, microstructure, and ferrite requirements, with explicit compliance confirmed. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

14442

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A @ 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and DMV 25.7N complies with these requirements. Source: DMV_STANDARD_BOOK/02 - ...

Open

14443

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

14444

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed on the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - U...

Open

14445

5.2

AI

No

add date

Compliance with the NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 is not demonstrated. Available documents only confirm partial or conditional feasibility for hydrostatic, ultrasonic, and eddy current testing, with eddy ...

Open

14446

5.2

AI

No

add date

No provided document confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that NDE to this acceptance criterion is feasible or included for the specified pipe dimension at Montbard. So...

Open

14447

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) as required, with no deviations or special tolerances specified by TechnipFMC or the customer request. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDAR...

Open

14448

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be pickled or bright annealed, fulfilling the requirement for white pickled or bright annealed pipes. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14449

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods (indelible ink, vibro-etching) include heat and DMV lot numbers, ensuring compliance for all pipes at Montbard ...

Open

14450

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

14451

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

14452

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

14453

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

14454

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products being delivered as required by SIR205 and section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

14455

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

14456

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or required metallurgical and non-destructive test results. EN 10204 3.1 certificates may...

Open

14457

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 Rev. 6, as specified for the order. Grade, product form, and standards are explicitly confirmed for compliance. Sou...

Open

14458

1.0

AI

No

add date

Manufacturing process is qualified according to NORSOK M-650/ISO 17782, fulfilling the requirement for supplier qualification relevant to the product supplied. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

14459

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm for hot finished, 10.925 mm for cold finished), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 require...

Open

14460

3.1

AI

No

add date

AOD or equivalent refining is used 100% for MST-Tubes, and DMV 25.7N complies with the required chemical analysis per Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

14461

3.1

AI

No

add date

DMV 25.7N (UNS S32760) is manufactured according to NORSOK M-650 qualified procedures, with accreditation for WT up to 31.75 mm, covering the requested WT of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

14462

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed in accordance with ASTM A790, with manufacturing process qualified to NORSOK M-650, and process ensures free circulation of heating and cooling media. Certification incl...

Open

14463

4.1

AI

No

add date

There is no evidence that impact, tensile, hardness, corrosion testing, and microstructure examinations are performed for each heat and heat treatment lot as defined in ASTM A790. Test frequency, lot definition, and required test types are not confir...

Open

14464

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required by the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

14465

4.1

AI

No

add date

Tensile testing per ASTM A790 is confirmed, but there is no evidence of CVN (Charpy), hardness, corrosion, or microstructure testing, nor confirmation of required test directions or sampling locations as specified in Table 3. Requirement is not fulfi...

Open

14466

4.2

AI

No

add date

Tensile testing is performed at room temperature with criteria and frequency matching DMV 25.7N requirements, and hardness testing is performed with results in HRC. Compliance with NORSOK MDS D51 and ASTM A790 ensures fulfillment of tensile and maxim...

Open

14467

4.2

AI

No

add date

No provided document confirms that DMV 25.7N meets the specified mechanical requirements (tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, hardness max 310 HBW). No direct test data or explicit statements of compliance are pres...

Open

14468

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness requirements for these standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive...

Open

14469

4.3

AI

No

add date

Pipe wall thickness of 18.26 mm allows for transverse Charpy specimens, meeting impact property requirements for both transverse and longitudinal directions at -46°C as specified. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished prod...

Open

14470

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination to ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels. Grain size examination is only addressed for austenitic materials, not duplex grades. ...

Open

14471

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination; requirement not addressed for ferrite balance and intermetallic phases. Source: DMV_STANDARD_BOOK/12 - Special Te...

Open

14472

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic phases; isolated phases are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

14473

4.4.2

AI

No

add date

No information is provided regarding the detection, recording, or micrographic documentation (at 400x or higher) of intermetallic phases as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Micrographic E...

Open

14474

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at actual magnification (400x minimum) with a scale bar if intermetallic phases are not detected; requirements for actual magnification and scale bar ...

Open

14475

4.4.2

AI

No

add date

No evidence of procedures for reporting centerline intermetallic stringers or acceptance criteria based on CVN and corrosion test results in the provided documents. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I.doc, DMV_STANDAR...

Open

14476

4.4.2

AI

No

add date

NORSOK digests allow isolated intermetallic precipitates below 10µm and not distributed over the whole specimen, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed. No other relevant docum...

Open

14477

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781 is provided; only grain size measurement is discussed. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Microgr...

Open

14478

4.4.3

AI

No

add date

No provided document specifies acceptance criteria for micrographic examination or metallurgical properties for DMV 25.7N; procedures and standards are mentioned, but required acceptance values or criteria are absent for the order in question. Source...

Open

14479

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range in the referenced documents. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK M...

Open

14480

4.5

AI

No

add date

No acceptance criteria for metallurgical properties are specified or listed for DMV 25.7N; the referenced section and relevant details are absent from the provided documents. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_B...

Open

14481

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) requires no pitting at 20X magnification and weight loss < 1.0 g/m², matching the client requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

14482

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDA...

Open

14483

5.2

AI

No

add date

No evidence that 100% ultrasonic testing per ASTM E213 or ISO 10893-10 is performed after all processing steps or that calibration notches meet the specified requirements; only dimensional capability is confirmed for ultrasonic testing, not process o...

Open

14484

5.2

AI

No

add date

100% qualitative anti-mixing PMI check is performed on standard production at Montbard using appropriate instruments, fulfilling the general NDE requirement for positive material identification. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - ...

Open

14485

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair; NDE feasibility and general practices are mentioned, but the specific acceptance criterion is ...

Open

14486

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed as per the applicable ASTM standards (including ASTM A790/A999) for the relevant size range, with no deviations or special requirements stated by TechnipFMC or in the inquiry, fulfilling th...

Open

14487

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed (ASTM A790) and white pickled or bright annealed (NORSOK MDS S01), directly fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790, NORSOK MDS S01.

Open

14488

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

14489

10.0

AI

No

add date

No evidence of the manufacturer's quality-assurance system (such as ISO 9001 certification by a competent EEA body) is provided in the relevant documents or excerpts reviewed. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BO...

Open

14490

10.1

AI

No

add date

No evidence provided that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certificat...

Open

14491

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling supplier qualification documentation per SIR1...

Open

14492

10.2

AI

No

add date

No explicit confirmation that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205 is provided in the available documents or metadata. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_...

Open

14493

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14494

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control, with compliance to ASTM A790 and NORSOK M-630 implied by reference in the customer specification and the mill's quality system. Source: 14-03 - Certific...

Open

14495

10.2

AI

No

add date

No provided document contains the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or test results for the ...

Open

14496

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, fulfilling the requirement for manufacturer and process qualification and compliance with...

Open

14497

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14498

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits and PREN ≥ 40 as specified in Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14499

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

14500

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

14501

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

14502

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specified thickness loc...

Open

14503

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 as referenced by NORSOK MDS D51 and ASTM A790, with DMV 25.7N meeting the specified tensile and hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

14504

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW, as specified in Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

14505

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, meeting the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 -...

Open

14506

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C (transverse: 45J/35J, longitudinal: 65J/50J) with correct test direction and sub-size reduction factors for wall thickness ≥6mm; the specified pipe dimensions allow f...

Open

14507

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or fulfilled. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

14508

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

14509

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

14510

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

14511

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

14512

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

14513

4.4.2

AI

No

add date

Findings of intermetallic stringers must be reported, and acceptance is based on CVN and corrosion test results as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

14514

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully fulfilled. Source:...

Open

14515

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

14516

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and ...

Open

14517

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in accordance with ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14518

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

14519

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORS...

Open

14520

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A @ 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², meeting the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

14521

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

14522

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, which are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-0...

Open

14523

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/650 are not fully addressed. For OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at extra cost. No confirmation of full-length dye p...

Open

14524

5.2

AI

No

add date

No explicit confirmation that indications greater than the calibration notch are treated as defects requiring rejection or repair; acceptance criteria based on calibration notch are not specified for NDE in the referenced documents or for the request...

Open

14525

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and ASTM A999 as required, with no deviations specified by the customer. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A 376-0...

Open

14526

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14527

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

14528

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

14529

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

14530

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

14531

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified ...

Open

14532

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

14533

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the specification and documentation sections. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NOR...

Open

14534

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or required metallurgical and non-destructive test results. Only the country of origin of...

Open

14535

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all referenced mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STA...

Open

14536

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14537

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N (up to WT = 31.75 mm, cold finished up to WT = 10.925 mm) but not to ISO 17782; no evidence of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK...

Open

14538

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

14539

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14540

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements, with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/0...

Open

14541

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

14542

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

14543

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

14544

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK M-630 MDS D51 Rev 6 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), corrosion, and microstructure tests are performe...

Open

14545

4.2

AI

No

add date

Tensile testing is performed in accordance with ASTM A370 or ISO 6892-1, and the material meets the required tensile and maximum hardness properties of Table 4 as specified in NORSOK MDS D51 and ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

14546

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

14547

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfills the requirement as the pipe wall thickness exceeds the minimum required by ASTM and ISO standards. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

14548

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -46°C (≥45 J average, 35 J single transverse; ≥65 J average, 50 J single longitudinal if transverse not possible) for thickness ≥6 mm. The specified pipe dimensions allow for requir...

Open

14549

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

14550

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

14551

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

14552

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

14553

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

14554

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

14555

4.4.2

AI

No

add date

No document fully prohibits intermetallic phases and/or precipitates if CVN testing cannot be completed; the closest reference allows isolated precipitates below 10 µm, which does not meet the stricter client requirement. Source: DMV_STANDARD_BOOK/02...

Open

14556

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

14557

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching methods, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and...

Open

14558

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in accordance with ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

14559

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, chemical composition, ferrite content, and corrosion/impact requirements. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

14560

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is met by DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

14561

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

14562

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available and applicable for the specified pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultrasonic testing...

Open

14563

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled. Standard NDE methods (hydrostatic, EC, UT) for the requested OD (219.1 mm) are only available at extra cost or are not feasible at the M...

Open

14564

5.2

AI

No

add date

The available documents do not explicitly state the NDE acceptance criterion that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, and standard NDE is not available for the requeste...

Open

14565

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are confirmed to be per the applicable ASTM standards (including ASTM A999), with no deviations or overrides specified by TechnipFMC for this inquiry. Source: DMV_STANDARD_BOOK/07-01 - General i...

Open

14566

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14567

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

14568

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

14569

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

14570

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification de...

Open

14571

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to products and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest N...

Open

14572

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO177...

Open

14573

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical...

Open

14574

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the item table and confirmed by the digest, including all mechanical, chemical, and testing requirements. Source: DMV_STANDARD_BOOK/02-04-03 - ...

Open

14575

1.0

AI

No

add date

Supplier is NORSOK M-650 accredited for UNS S32760 / DMV25.7N but not accredited to ISO 17782 as required; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14576

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process follows M-650 (or ISO 17782) qualified procedures, fulfilling the requirement for manufacturer and process qualification per NORSOK M-65...

Open

14577

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14578

3.1

AI

No

add date

No explicit chemical composition data or direct confirmation that all specified element limits for S32760 are met; only general compliance is stated without detailed values or full validation to the requirement table possible. Source: DMV_STANDARD_BO...

Open

14579

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

14580

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: ASTM A790, NORSOK MDS D51 Rev 06

Open

14581

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

14582

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and per 100 pieces, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/...

Open

14583

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, longitudinal if not possible), and corrosion/microstructure tests are performed at specified ...

Open

14584

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

14585

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

14586

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for 18.26mm wall thickness and 219.1mm OD pipe as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impac...

Open

14587

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements at -46°C (≥45 J average, 35 J single transverse; ≥65 J average, 50 J single longitudinal if transverse not possible) for thickness ≥6 mm. The specified pipe dimensions allow for require...

Open

14588

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

14589

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

14590

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

14591

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases as required. Source: DMV_STAN...

Open

14592

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

14593

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria based on CVN and corrosion...

Open

14594

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. No evidence of stricter compliance...

Open

14595

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

14596

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

14597

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

14598

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

14599

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14600

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A @ 50°C, 24h) requires no pitting at 20X magnification and weight loss < 1.0 g/m²; DMV 25.7N complies. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Diges...

Open

14601

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source: DM...

Open

14602

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

14603

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed as met; only ASTM A790/A999 NDE is detailed. For OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at e...

Open

14604

5.2

AI

No

add date

No provided documentation explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor that such NDE acceptance criteria are standardly applied or feasible for t...

Open

14605

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the specified pipe, with no overriding customer specification or drawing indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01...

Open

14606

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14607

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods include heat number and DMV lot number, ensuring compliance with the requirement. Source: DMV_STANDARD...

Open

14608

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

14609

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

14610

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

14611

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling the supplier qualification documentation requ...

Open

14612

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

14613

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

14614

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution annealing parameters, an...

Open

14615

1.0

AI

No

add date

Supplier is NORSOK M-650 accredited for UNS S32760 / DMV25.7N but not accredited to ISO 17782, as required. No evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14616

3.1

AI

No

add date

AOD or equivalent steel melt refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14617

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

14618

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling as outlined in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

14619

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

14620

4.3

AI

No

add date

Charpy V-notch testing is feasible and fulfilled for the specified pipe dimensions according to ASTM A370 and ISO 148-1 requirements for minimum wall thickness. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Imp...

Open

14621

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

14622

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

14623

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

14624

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases as required. Source: DMV_STAN...

Open

14625

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

14626

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

14627

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates if CVN testing cannot be completed, or they allow isolated precipitates below 10 µm, which does not meet the stricter client requirement of not permit...

Open

14628

4.4.3

AI

No

add date

Ferrite content is checked as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite determination methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

14629

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

14630

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N according to NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev ...

Open

14631

4.5

AI

No

add date

ASTM G48 Method 'A' corrosion testing at 50°C for 24h in accordance with ISO 17781 is not explicitly mentioned or referenced; compliance cannot be confirmed based on the provided information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Mon...

Open

14632

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO ...

Open

14633

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

14634

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

14635

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, which are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-0...

Open

14636

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. While ASTM A790/ASTM A999 NDE (EC or UT) is confirmed, Montbard plant feasibility for eddy current testing at the requested OD and length ...

Open

14637

5.2

AI

No

add date

None of the relevant documents explicitly confirm that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair of pipe and tubing as specified in the requirement. NDE methods and general...

Open

14638

6.0

AI

No

add date

Dimensional tolerances for the requested pipe are per the applicable ASTM standard (ASTM A790 referencing ASTM A999), with no override specified in the customer requirements or context. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_S...

Open

14639

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14640

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 (§14), requiring full traceability to melt and heat treatment lot. Marking methods include heat number, lot number, and other traceable information, ensuring compliance with the requiremen...

Open

14641

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

14642

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

14643

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, and the QTR number is included in the certificate, fulfilling the requirement for supplier qualification documentation per SIR131. Source: DMV_STANDARD_BOOK/...

Open

14644

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

14645

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - ...

Open

14646

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and full metallurgical and NDT results—are not fully pr...

Open

14647

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, Digest NORSOK MD...

Open

14648

1.0

AI

No

add date

Supplier is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to certain wall thicknesses) but not accredited to ISO 17782; full qualification per NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR is not confirmed for review...

Open

14649

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

14650

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14651

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed by heat analysis with supplier certification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Dige...

Open

14652

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

14653

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14654

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

14655

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

14656

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) includes tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, all in compliance wit...

Open

14657

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

14658

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

14659

4.3

AI

No

add date

Charpy V-notch testing is feasible and the requirement is fulfilled as the pipe wall thickness exceeds the minimum required for testing according to ASTM A370 and ISO 148-1. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/1...

Open

14660

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements at -46°C (≥45 J average, 35 J single transverse; ≥65 J average, 50 J single longitudinal if transverse not possible) for thickness ≥6 mm. The specified pipe (18.26 mm WT) meets these cr...

Open

14661

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-coll...

Open

14662

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is specified, fulfilling the requirement for suitable etchant(s) as listed in ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

14663

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

14664

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

14665

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

14666

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

14667

4.4.2

AI

No

add date

The available documents either do not address the prohibition of intermetallic phases and/or precipitates when CVN testing cannot be completed, or they allow isolated precipitates, which does not meet the stricter client requirement of not permitting...

Open

14668

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

14669

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

14670

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

14671

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 will be performed or is referenced in the documentation provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

14672

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements, with compliance to NORSOK M-650/ISO 17782 qualification processes. Source: DMV_STANDARD_B...

Open

14673

4.5

AI

No

add date

Corrosion test per ISO 17781 G48 Method A at 50°C for 24 hours is performed with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and DMV 25.7N complies with these requirements. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

14674

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destruct...

Open

14675

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed on the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - U...

Open

14676

5.2

AI

No

add date

NDE methods (hydrostatic, ultrasonic, eddy current) for the specified pipe size are either not feasible, only available at extra cost, or require technical consultation, and there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 177...

Open

14677

5.2

AI

No

add date

No document explicitly confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair; NDE acceptance criteria and protocols are not detailed for the specified requirement or dimension at Montbard...

Open

14678

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no evidence of a deviation or special tolerance request in the customer specification. Source: DMV_STANDARD_BOOK/07-01 - General informatio...

Open

14679

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14680

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-0...

Open

14681

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated in NORSOK MDS D51 Rev 06, §14. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14682

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

14683

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

14684

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification de...

Open

14685

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

14686

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the specification section. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06....

Open

14687

10.2

AI

No

add date

Most documentation and certification requirements are addressed, including NORSOK M-650/ISO 17782 identification, steel melting practice and refining method, and heat treatment condition, but the specific steel producer of the starting material is no...

Open

14688

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified up to the required wall thickness...

Open

14689

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability or full compliance with both NORSOK M-650 and ISO 17782 as required by the specification. Source: D...

Open

14690

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

14691

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14692

3.1

AI

No

add date

Chemical composition for UNS S32760 conforms to Table 2 of ASTM A790, matching the specified limits, with heat analysis and supplier certification provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-0...

Open

14693

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing and heat treatment qualified and performed in compliance with NORSOK M-650/ISO 17782. Free circulation of heating and cooling me...

Open

14694

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

14695

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

14696

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specifi...

Open

14697

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

14698

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

14699

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

14700

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if transverse is not po...

Open

14701

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching for intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and examination in accordance ...

Open

14702

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

14703

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

14704

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

14705

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

14706

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

14707

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10 µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully met. Source:...

Open

14708

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

14709

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

14710

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

14711

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

14712

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content...

Open

14713

4.5

AI

No

add date

DMV 25.7N meets the pitting corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours, with no pitting at 20X magnification and weight loss less than 1.0 g/m², matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

14714

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destruct...

Open

14715

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, which are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-0...

Open

14716

5.2

AI

No

add date

NDE per ASTM A790 is available, but compliance with NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 NDE requirements is not confirmed. For the requested OD (219.1 mm), standard eddy current testing is not feasible, and hydrostatic, ultrasonic, and ed...

Open

14717

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor that such NDE acceptance criteria are standardly feasible for the requested pip...

Open

14718

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 for ASTM A790 pipe) as required, with no evidence of a deviation or special tolerance request from TechnipFMC in the provided context. Source: DMV_STANDARD_BOOK/07-01 - General in...

Open

14719

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14720

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

14721

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' confirming the requirement is met. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev...

Open

14722

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

14723

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

14724

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

14725

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

14726

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

14727

10.2

AI

No

add date

No provided document includes all required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or comp...

Open

14728

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, Digest NORSOK MDS D51 Rev 06.d...

Open

14729

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability or full compliance with both NORSOK M-650/ISO 17782 as required for the exact product supplied. Source:...

Open

14730

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

14731

3.1

AI

No

add date

AOD or equivalent refining is standard for duplex stainless steels and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS...

Open

14732

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PRE ≥ 40, as required by Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat to ensure compliance. Source: DMV_STANDARD_...

Open

14733

3.2

AI

No

add date

Manufacturing process is qualified to NORSOK M-650, heat treatment is solution annealed followed by accelerated cooling as per ASTM A790, and furnaces are M-650 accredited, ensuring compliance with all specified requirements. Source: DMV_STANDARD_BOO...

Open

14734

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

14735

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and per 100 pieces, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/...

Open

14736

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations, all per NORSOK and ASTM re...

Open

14737

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Hardness testing is also performed as specified. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

14738

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

14739

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

14740

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C, including minimum absorbed energy values and sub-size reduction factors. The specified pipe dimensions allow for required transverse and longitudinal Charpy V-notch t...

Open

14741

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching for intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and examination in accordance ...

Open

14742

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

14743

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

14744

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

14745

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

14746

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

14747

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is...

Open

14748

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

14749

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance is based on im...

Open

14750

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in accordance with ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

14751

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the applicable standards or documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.d...

Open

14752

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORS...

Open

14753

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

14754

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

14755

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

14756

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled; only ASTM A790/A999 NDE is referenced. For the specified OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/ultrasonic tests...

Open

14757

5.2

AI

No

add date

No provided document explicitly states that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor confirms that NDE with this acceptance criterion will be performed as standard fo...

Open

14758

6.0

AI

No

add date

Dimensional tolerances are confirmed as per the applicable ASTM standard (ASTM A790/A999) for the specified pipe dimensions, with no overriding requirements from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_ST...

Open

14759

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14760

8.0

AI

No

add date

Marking per ASTM A790 ensures full traceability to melt and heat treatment lot, and standard plant marking methods include heat number and DMV lot number to meet this requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

14761

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 explicitly states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14762

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

14763

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

14764

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification de...

Open

14765

10.2

AI

No

add date

ISO 9001 certification is provided, and EN 10204 type 3.1 certificates with traceability and required documentation are standard, fulfilling the requirement for documentation traceable to the products and transmission to TechnipFMC as per SIR205. Sou...

Open

14766

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx...

Open

14767

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

14768

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or results of required metallurgical and non-destructive testing. Only general references...

Open

14769

1.0

AI

No

add date

DMV 25.7N seamless pipe is listed as compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, and is M-650 qualified for the required wall thickness. Source: Item Table, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14770

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not to ISO 17782; full qualification per NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR is not confirmed. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

14771

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N, with manufacturing processes qualified per NORSOK M-650 (or ISO 17782), and compliance with NORSOK M-630 MDS D51 Rev. 6 is referenced. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

14772

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14773

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790 as required, with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 7...

Open

14774

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

14775

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

14776

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

14777

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, in accordance with NORSOK MDS ...

Open

14778

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 for NORSOK MDS D51/ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

14779

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

14780

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement for both longitudinal and transverse directions for wall thickness >6mm as required by the standards. Source: DMV...

Open

14781

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements, including Charpy V-notch testing at -466C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal. T...

Open

14782

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution for detecting ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

14783

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

14784

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

14785

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

14786

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

14787

4.4.2

AI

No

add date

No provided documentation fully prohibits intermetallic phases and/or precipitates if CVN testing cannot be completed; the closest reference allows isolated precipitates below 10µm, which does not meet the stricter client requirement for complete abs...

Open

14788

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

14789

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosio...

Open

14790

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

14791

4.5

AI

No

add date

No explicit evidence of ASTM G48 Method 'A' (50°C, 24h) corrosion testing in accordance with ISO 17781 is provided; compliance cannot be confirmed based on available information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.d...

Open

14792

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content...

Open

14793

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

14794

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

14795

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed on the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - U...

Open

14796

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/NORSOK M-650/ISO 17782 are not confirmed. Standard NDE methods (hydrostatic, EC, UT) are either not fully feasible for the specified OD at Montbard or only available at extra cost and req...

Open

14797

5.2

AI

No

add date

None of the provided documents confirm that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor do they specify the required NDE acceptance criteria or confirm standard NDE feas...

Open

14798

6.0

AI

No

add date

Dimensional tolerances for the requested pipe are per ASTM A790 and its referenced standard ASTM A999, with no overriding requirements stated, fulfilling the requirement for ASTM-based tolerances unless otherwise specified. Source: DMV_STANDARD_BOOK/...

Open

14799

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14800

8.0

AI

No

add date

Marking per ASTM A790 and plant marking methods ensure mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDA...

Open

14801

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable for DMV 25.7N seamless pipe as per the client specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 R...

Open

14802

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

14803

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the required quality-assurance system criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

14804

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification dem...

Open

14805

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

14806

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

14807

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and n...

Open

14808

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, covering all standard and supplementary requirements, including chemical, mechanical, and testing criteria. M-650 qualification is confirmed ...

Open

14809

1.0

AI

No

add date

Supplier is NORSOK M-650 accredited for UNS S32760 / DMV25.7N but not accredited to ISO 17782; full qualification per NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR is not confirmed. Source: DMV_STANDARD_BOOK/02-04-03 - Diges...

Open

14810

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

14811

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. The chemical composition table matches the standard and compliance is confirmed for the proposed grade. Sourc...

Open

14812

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

14813

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

14814

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ...

Open

14815

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations a...

Open

14816

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

14817

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

14818

4.3

AI

No

add date

Pipe wall thickness (18.26 mm) exceeds the minimum required for Charpy V-notch testing per ASTM and ISO standards; testing as per ASTM A370 or ISO 148-1 is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for ho...

Open

14819

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements: Charpy V-notch testing at -466C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal; pipe wall thickness (...

Open

14820

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching for intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and examination in accordance ...

Open

14821

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution for detecting ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

14822

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

14823

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STANDA...

Open

14824

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

14825

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: ASTM A790, NORSOK MDS D51 Rev 06.

Open

14826

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

14827

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully fulfilled. Source: DMV_STANDARD_...

Open

14828

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

14829

4.4.3

AI

No

add date

Micrographic examination per ISO 17781 is specified, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impact ...

Open

14830

4.4.3

AI

No

add date

Ferrite content of 35% to 60% is specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14831

4.5

AI

No

add date

No explicit evidence of ASTM G48 Method 'A' (50°C, 24h) corrosion testing in accordance with ISO 17781 is provided; compliance cannot be confirmed based on the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard p...

Open

14832

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive, micrographic, ferrite, and corrosion tests, with explicit compliance and M-650 qualification up to the required wall thickness. Source: DMV_STANDAR...

Open

14833

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

14834

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

14835

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, which are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-0...

Open

14836

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not validated. Standard NDE methods (EC, UT, hydrostatic) for the requested OD and length are only available at extra cost and require confirmation with Technical Advisor...

Open

14837

5.2

AI

No

add date

None of the referenced documents explicitly confirm that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, and standard NDE is not available for the requested OD at Montbard, so t...

Open

14838

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790/A999) for the specified pipe dimensions, with no deviations stated in the client specification or drawing. Source: DMV_STANDARD_BOOK/07-01 - General information.do...

Open

14839

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14840

8.0

AI

No

add date

Marking per ASTM A790 and plant marking methods ensure mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDA...

Open

14841

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

14842

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

14843

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

14844

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness for the specified size and product form. Source: DMV_STANDARD_BO...

Open

14845

10.2

AI

No

add date

Certification to EN 10204 type 3.1 is provided, including heat treatment, steel manufacturer, melting/refining practice, NORSOK M-650/ISO17782 manufacturing summary or QTR number, and traceability to delivered products. Source: DMV_STANDARD_BOOK/02 -...

Open

14846

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 ...

Open

14847

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. Other required ...

Open

14848

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the item table and confirmed by the digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-0...

Open

14849

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of full qualification to both NORSOK M-650/ISO 17782 or availability of QTR/MPCR documentation for review as required by the spe...

Open

14850

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

14851

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition complies with Table 2 as specified for DMV 25.7N seamless pipe per ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - ...

Open

14852

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed by supplier certification and heat analysis. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03...

Open

14853

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

14854

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

14855

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

14856

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

14857

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled for DMV 25.7N per NORSOK MDS D51...

Open

14858

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 as required for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

14859

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

14860

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions (18.26mm WT, 219.1mm OD). Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impac...

Open

14861

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C, with minimum absorbed energy values for transverse and longitudinal specimens, and the specified pipe dimensions allow for standard transverse Charpy V-notch testing....

Open

14862

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

14863

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B is specified for showing ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

14864

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and if each is below 10µm, matching the requirement for distribution and maximum size of intermetallic...

Open

14865

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

14866

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

14867

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK/0...

Open

14868

4.4.2

AI

No

add date

No provided documentation prohibits all intermetallic phases and/or precipitates when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10µm, which does not meet the stricter client requirement. Source: DMV_STA...

Open

14869

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

14870

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corro...

Open

14871

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50°C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

14872

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO ...

Open

14873

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A @ 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and is confirmed to comply with these requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

14874

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

14875

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, which are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-0...

Open

14876

5.2

AI

No

add date

No evidence that NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782 are fulfilled. Standard NDE methods (hydrostatic, UT, EC) are not fully feasible for the requested OD at Montbard, and full-length dye penetrant testing...

Open

14877

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair; NDE acceptance criteria and required testing are not demonstrated for the specified...

Open

14878

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and referenced ASTM A999, with no overriding requirements from TechnipFMC stated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a ...

Open

14879

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14880

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring compliance with the requirement for traceab...

Open

14881

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14882

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

14883

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

14884

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling the requirement for supplier qualification do...

Open

14885

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

14886

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary or QTR...

Open

14887

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of required metallurgical and non-destructive testing for the specific orde...

Open

14888

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_...

Open

14889

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N (up to WT 31.75 mm) but not to ISO 17782; no evidence provided for availability of QTR/MPCR for review as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14890

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

14891

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14892

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed by heat analysis per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790....

Open

14893

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

14894

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

14895

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with the required frequency, directly referencing Table 3 for test specimen sampling as outlined in the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

14896

4.1

AI

No

add date

Test sampling requirements for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions, are fulfilled for DM...

Open

14897

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, meeting the tensile and maximum hardness properties of Table 4 as required for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

14898

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

14899

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

14900

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements, including Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal. The specifi...

Open

14901

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching by 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

14902

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is explicitly required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_...

Open

14903

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

14904

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

14905

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

14906

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

14907

4.4.2

AI

No

add date

No provided source prohibits all intermetallic phases and/or precipitates if CVN testing cannot be completed; the closest source allows isolated precipitates below 10μm, which does not meet the stricter client requirement of zero tolerance in this ca...

Open

14908

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

14909

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

14910

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

14911

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 will be performed or is referenced in the documentation provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

14912

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

14913

4.5

AI

No

add date

DMV 25.7N undergoes a pitting corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_...

Open

14914

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement is not fulfilled based on the available information. Sou...

Open

14915

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

14916

5.2

AI

No

add date

NDE methods (hydrostatic, ultrasonic, eddy current) are either not fully feasible, require extra cost, or lack confirmation for the specific grade and specification (ASTM A790, NORSOK M-630/M-650) for the requested pipe dimensions. Full-length dye pe...

Open

14917

5.2

AI

No

add date

The available documents do not confirm that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor do they confirm the feasibility of the required NDE for the specified pipe dimens...

Open

14918

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and referenced ASTM A999, with no overriding specification from TechnipFMC. Requirement is fulfilled as tolerances default to the applicable ASTM standard for OD, WT, and ovality for hot finished products. Sou...

Open

14919

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14920

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 (§14), requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring compliance with the requirement for traceabili...

Open

14921

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14922

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

14923

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

14924

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

14925

10.2

AI

No

add date

Certification to EN 10204 type 3.1 is provided, including heat treatment, steel manufacturer, melting/refining practice, NORSOK M-650/ISO17782 manufacturing summary or QTR number, and traceability, fulfilling the requirement for documentation to be t...

Open

14926

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and standard for this application. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_...

Open

14927

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal, and sub-size redu...

Open

14928

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, ladle chemical analysis, solution annealing parameters, or results of all required metallurgical and non-destructive ...

Open

14929

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

14930

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; full qualification to both NORSOK M-650/ISO 17782 is not demonstrated and QTR/MPCR availability is not confirmed. Source: DMV_STANDARD_BOOK/0...

Open

14931

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N with the requested wall thickness, and the manufacturing process is qualified per NORSOK M-650/ISO 17782 with testing per NORSOK M-630 MDS D51 rev. 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

14932

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical analysis conforms to the specified table for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14933

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN requirements as per Table 2, with compliance confirmed by both ASTM A790 and NORSOK MDS D51 Rev 6 standards. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 -...

Open

14934

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N, and certification will state heat treatment per ASTM A790. Fr...

Open

14935

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

14936

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

14937

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled for DMV 25.7N per ASTM A790 and ...

Open

14938

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

14939

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

14940

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

14941

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

14942

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination and matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

14943

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

14944

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

14945

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

14946

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

14947

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates, which does not meet the stricter client requirement of not permitting any i...

Open

14948

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

14949

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

14950

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

14951

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50°C, 24h) in accordance with ISO 17781 is provided; neither standard nor test is mentioned or specified in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in M...

Open

14952

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spe...

Open

14953

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

14954

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

14955

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, meeting the requirement for both standard and dimensional capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02...

Open

14956

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790/NORSOK M-630 MDS D51 are not fully addressed. Hydrostatic or NDE (EC or UT) testing per ASTM A999 is confirmed, but NORSOK-specific NDE requirements are not demonstrated. For OD 219.1 mm, eddy current testing is ...

Open

14957

5.2

AI

No

add date

The specific NDE acceptance criterion that any indication greater than that produced by the calibration notch represents a defect, requiring rejection or repair, is not detailed in the referenced specifications. Additionally, Eddy current testing is ...

Open

14958

6.0

AI

No

add date

Dimensional tolerances are specified as per the applicable ASTM standard (ASTM A790/A999) for the requested product, with no alternative requirements from TechnipFMC indicated. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General infor...

Open

14959

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

14960

8.0

AI

No

add date

Marking per ASTM A790 §16.1 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAN...

Open

14961

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14962

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

14963

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

14964

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

14965

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

14966

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and compliant with the specified standards. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

14967

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice, refining method, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the actual steel producer's...

Open

14968

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and the manufacturing process is M-650 qualified up to the required wall thickness...

Open

14969

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and standards; requirement is fulfilled. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

14970

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

14971

3.1

AI

No

add date

AOD or equivalent refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14972

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PREN ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

14973

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

14974

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

14975

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

14976

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, all per NORSOK and AST...

Open

14977

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

14978

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 06 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

14979

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the ordered pipe dimensions and is fulfilled as required by the standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tes...

Open

14980

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C, with minimum absorbed energy values for both transverse and longitudinal directions, and the specified pipe dimensions allow for required testing directions and speci...

Open

14981

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching for intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and examination in accordance ...

Open

14982

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

14983

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

14984

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness requirements for these standards. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished ...

Open

14985

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

14986

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

14987

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

14988

4.4.2

AI

No

add date

No evidence that intermetallic phases and/or precipitates are completely prohibited if CVN testing cannot be completed; referenced documents allow isolated precipitates or do not address the requirement specifically. Source: DMV_STANDARD_BOOK/02-03-0...

Open

14989

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 ...

Open

14990

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corro...

Open

14991

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

14992

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

14993

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content...

Open

14994

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

14995

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

14996

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 or ISO 10893-10 is feasible and standards-compliant for the specified pipe dimensions; calibration notch requirements are covered by adherence to ASTM E213 standard. Source...

Open

14997

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/NORSOK M-650/ISO 17782 are not fully addressed; standard NDE methods (EC, UT, hydrostatic) are either not feasible, only available at extra cost, or require technical consultation for the...

Open

14998

5.2

AI

No

add date

None of the provided documents explicitly state that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, nor do they confirm that NDE with this acceptance criterion will be performed a...

Open

14999

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) as required, with no overriding tolerances specified by the customer or TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - T...

Open

15000

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15001

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

15002

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

15003

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

15004

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

15005

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification de...

Open

15006

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 manufacturing summary or QTR number, are provided and fulfill the requirement for documentation traceable to the products and trans...

Open

15007

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_...

Open

15008

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and results of all metallurgical and non-destructive testing...

Open

15009

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, Digest NORSOK MDS D51 Rev 06.d...

Open

15010

1.0

AI

No

add date

Supplier is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to certain wall thicknesses) but not accredited to ISO 17782, and there is no evidence of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/0...

Open

15011

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, fulfilling the requirement for manufacturer and process qualification and compliance with ...

Open

15012

3.1

AI

No

add date

AOD or equivalent refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15013

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15014

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat, confirming conformity to the requireme...

Open

15015

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

15016

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

15017

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

15018

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests, with specified locations and directions, is fulfilled. For the ordered p...

Open

15019

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

15020

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

15021

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, meeting the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in Mo...

Open

15022

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -466C (transverse: 45/35 J, longitudinal: 65/50 J) for thickness >6mm, and the specified pipe dimensions allow for required testing directions and specimen sizes. Source: D...

Open

15023

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

15024

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

15025

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

15026

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

15027

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected, fulfilling the requirem...

Open

15028

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

15029

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 includes etching to detect intermetallic phases, with findings reported and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acc...

Open

15030

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fulfilled. Source: DMV_STANDARD_...

Open

15031

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

15032

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching methods, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and...

Open

15033

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

15034

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50°C, 24h) in accordance with ISO 17781 is provided; neither standard nor test is mentioned in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant...

Open

15035

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

15036

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

15037

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor are their roles and responsibilities defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructiv...

Open

15038

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects is performed in accordance with ASTM E213 and ISO 10893-10 after all mechanical processing, heat treatments, and straightening, and the dimensional range is within equipment capability. Source: DMV_STA...

Open

15039

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. For the requested OD 219.1 mm, Eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at extra cost. Th...

Open

15040

5.2

AI

No

add date

No explicit confirmation that NDE acceptance criteria require rejection or repair of indications greater than the calibration notch; feasibility of required NDE for the specified dimension is not confirmed for Montbard plant. Source: DMV_STANDARD_BOO...

Open

15041

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no override specified in the customer requirements or context. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK...

Open

15042

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15043

8.0

AI

No

add date

Marking per ASTM A790 and plant marking methods ensure mandatory marking of heat number and DMV lot number, providing full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDA...

Open

15044

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

15045

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

15046

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, demonstrating qualification for the specified size and product ...

Open

15047

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03...

Open

15048

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - ...

Open

15049

10.2

AI

No

add date

Most required documentation and certification items (NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and test results) are either not provided or only referenced as ...

Open

15050

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 -...

Open

15051

1.0

AI

No

add date

Supplier is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to certain wall thicknesses) but not accredited to ISO 17782, and there is no confirmation of QTR/MPCR availability for review. Full qualification to NORSOK M-650/ISO 17782 and documen...

Open

15052

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to 31.75 mm WT, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

15053

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15054

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits and PREN requirements specified in Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15055

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification will state heat treatment condition as per ASTM A790. Pipes are processed to ensure ...

Open

15056

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, with a frequency of 1/lot for each test type. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

15057

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - De...

Open

15058

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure, with specified thickness locations, is fulfilled. For the ordered pipe dimensi...

Open

15059

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4 as specified in NORSOK MDS D51. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

15060

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

15061

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible as the pipe wall thickness exceeds the minimum required by the standards. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

15062

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C (transverse: avg 3 45 J, single 3 35 J; longitudinal: avg 3 65 J, single 3 50 J if transverse not possible). The specified pipe dimensions allow for required tra...

Open

15063

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

15064

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

15065

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10 μm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

15066

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases. Source: DMV_STANDARD_BOOK/02...

Open

15067

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

15068

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

15069

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

15070

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

15071

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or specified. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

15072

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

15073

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

15074

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/...

Open

15075

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A) at 506C for 24 hours is performed with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m8; DMV 25.7N complies. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

15076

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

15077

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available and applicable for the specified pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultrasonic testing...

Open

15078

5.2

AI

No

add date

NDE acceptance criteria per NORSOK/ASTM A790 are not confirmed as fulfilled; standard NDE methods (EC, UT, hydrostatic) are not fully feasible or included for the specified pipe size at Montbard, and there is no evidence of compliance with NORSOK-spe...

Open

15079

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor that such NDE acceptance criteria are standardly applied or feasible for the specified pipe size...

Open

15080

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) unless otherwise specified, with no deviations indicated in the customer specification or context. Source: 07.01 - General information.doc, 07.03.01 - Tolerances according t...

Open

15081

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15082

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

15083

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

15084

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

15085

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

15086

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size ...

Open

15087

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products being delivered as required by SIR205 and section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

15088

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control for mill inspection and referencing relevant standards and qualifications. Source: DMV_STANDARD_BOOK/02-04-03 -...

Open

15089

10.2

AI

No

add date

EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 identification, steel melting practice and refining method, heat treatment condition, heat number, chemical analysis, and test results, but only the country of origin of the steel supplier...

Open

15090

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified up to the required wall thickness. Source: Item Table,...

Open

15091

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782; no confirmation of QTR/MPCR availability for review. Requirement for qualification to both NORSOK M-650/ISO 17782 and documentation availability is not fully met. Source: DMV_S...

Open

15092

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

15093

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat to ensure conformity. Source: 02-03-01...

Open

15094

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

15095

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

15096

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

15097

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified locations, in compliance with ASTM A790 and NORSOK ...

Open

15098

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets or exceeds the required tensile and maximum hardness properties of Table 4 for DMV 25.7N (UNS S32760). Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

15099

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

15100

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and standards; requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/1...

Open

15101

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal. The specified pipe dimensions allow...

Open

15102

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

15103

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

15104

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

15105

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

15106

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

15107

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

15108

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

15109

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 ...

Open

15110

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with acceptance based on impa...

Open

15111

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in accordance with ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

15112

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation or standards list. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

15113

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements, with microstructure acceptance referenced to ISO 17781. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

15114

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02...

Open

15115

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712 or equivalent standards. Requirement not fulfilled based on available...

Open

15116

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is feasible and standards-compliant for the specified pipe dimensions; acceptance of ASTM E213 implies compliance with calibration notch requirements. Source: DMV_STANDARD...

Open

15117

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled; available documentation only covers ASTM A790/A999 NDE, and plant feasibility for required NDE methods (hydrostatic, ultrasonic, eddy cu...

Open

15118

5.2

AI

No

add date

No explicit confirmation that NDE acceptance criteria require rejection or repair of indications greater than the calibration notch; standard NDE methods are not feasible or only available at extra cost for the requested size at the plant. Requiremen...

Open

15119

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 for ASTM A790 pipe), with no override specified in the customer requirements or context. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - To...

Open

15120

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15121

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

15122

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

15123

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

15124

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size ...

Open

15125

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

15126

10.2

AI

No

add date

EN 10204 Type 3.1 material certificate is provided, including all information required by ASTM A790 and NORSOK M-630, and validated by Quality Control as per specification requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

15127

10.2

AI

No

add date

No specific documentation or data is provided for NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or results of required metallurgical and non-destructive testing. O...

Open

15128

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

15129

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 or availability of QTR/MPCR documentation; only NORSOK M-650 accreditation is mentioned, not ISO 17782 as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

15130

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

15131

3.1

AI

No

add date

AOD or equivalent steel refining is required for 100% of production, and the chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 ...

Open

15132

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed by supplier certification and heat analysis per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02...

Open

15133

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

15134

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

15135

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

15136

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified l...

Open

15137

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4 as specified in NORSOK MDS D51. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

15138

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW, fulfilling Table 4 mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

15139

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, meeting the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in Mo...

Open

15140

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if transverse is not p...

Open

15141

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

15142

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is explicitly required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_...

Open

15143

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

15144

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

15145

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

15146

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

15147

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size. No other relevant information provided support...

Open

15148

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis per ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - S...

Open

15149

4.4.3

AI

No

add date

Micrographic examination is performed as per ISO 17781 with specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance is based o...

Open

15150

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

15151

4.5

AI

No

add date

ASTM G48 Method 'A' corrosion testing at 50°C for 24h in accordance with ISO 17781 is not explicitly mentioned or confirmed; compliance cannot be verified based on the provided information. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destr...

Open

15152

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15153

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

15154

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

15155

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is confirmed, with calibration expected to follow ASTM E213 Figure 3 as required. Pipe dimensions are within equipment capability. Untested ends will be cut off, ensuring ...

Open

15156

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not addressed. Standard NDE methods (EC, UT, hydrostatic) for the specified OD are only available at extra cost or require technical consultation, and full-length d...

Open

15157

5.2

AI

No

add date

No provided documentation confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, and standard NDE methods for this criterion are either not feasible or only available at extra cost for the r...

Open

15158

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) for the specified pipe, with no deviations or special requirements indicated by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-0...

Open

15159

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15160

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

15161

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORS...

Open

15162

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

15163

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

15164

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

15165

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

15166

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control for mill inspection and referencing the relevant standards and qualification requirements. Source: DMV_STANDARD...

Open

15167

10.2

AI

No

add date

The EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the ...

Open

15168

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 Rev. 6. Compliance for DMV 25.7N is explicitly stated, including all relevant mechanical, chemical, and testing req...

Open

15169

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor confirmation of QTR/MPCR documentation availability for review by TechnipFMC. MST-Tubes is NORSOK M-650 accredited for DMV25.7N but not ISO 1...

Open

15170

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 and meets NORSOK M-630 MDS D51 Rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

15171

3.1

AI

No

add date

AOD or equivalent refining is used 100% for DMV 25.7N, and the chemical analysis complies with the required specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

15172

3.1

AI

No

add date

MST-Tubes F is M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the inquiry for DMV 25.7N with WT = 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

15173

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed in accordance with ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650/ISO 17782. Free circulation of heating/cooling media is ensured by compli...

Open

15174

4.1

AI

No

add date

There is no explicit evidence that one set of impact, tensile, hardness, corrosion testing, and microstructure examinations is carried out for each heat and heat treatment lot as defined in ASTM A790. Only partial or feasibility information is provid...

Open

15175

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

15176

4.1

AI

No

add date

Test sampling requirements for test methods, directions, and locations per Table 3 (including tensile and CVN test directions and sampling locations) are not fully validated by the provided documents; missing confirmation of test directions and CVN t...

Open

15177

4.2

AI

No

add date

Tensile testing is performed per lot at room temperature with criteria matching or exceeding Table 4, and referenced standards require testing in accordance with ASTM A370 or ISO 6892-1. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

15178

4.2

AI

No

add date

None of the provided documents confirm fulfillment of the required mechanical properties (tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, hardness max 310 HBW/32 HRC) for DMV 25.7N; referenced standards either do not specify t...

Open

15179

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, meeting the minimum wall thickness requirements for both standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testi...

Open

15180

4.3

AI

No

add date

Impact testing at -46°C with specified absorbed energy values is feasible and can be fulfilled for pipe with 18.26mm wall thickness, as both ASTM and ISO rules confirm transverse specimens are possible for this size. Source: DMV_STANDARD_BOOK/12 - Sp...

Open

15181

4.4.1

AI

No

add date

No evidence of metallographic preparation and examination according to ISO 17781 or specification of the required etchant solution for 25 Cr Duplex stainless steels; only grain size measurement for austenitic materials is addressed, not duplex grades...

Open

15182

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination of ferrite balance and intermetallic phases is provided. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - De...

Open

15183

4.4.2

AI

No

add date

The microstructure must be basically free from intermetallic precipitates, but isolated precipitates are allowed if not distributed over the whole specimen and if their dimension is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_...

Open

15184

4.4.2

AI

No

add date

No information or procedures are provided regarding the detection, recording, or micrographic documentation (at 400x or higher) of intermetallic phases; only grain size measurement is discussed in the relevant document. Source: DMV_STANDARD_BOOK/12 -...

Open

15185

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at 400x minimum magnification with a scale bar and actual magnification if intermetallic phases are not detected. Partial mention of 400x photos, but ...

Open

15186

4.4.2

AI

No

add date

Referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates below 10µm, which does not meet the stricter client requirement of zero toleranc...

Open

15187

4.4.3

AI

No

add date

No information is provided confirming ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781; only grain size measurement is discussed, not ferrite content determination as required. Source: DMV_STANDARD_BOOK/12 - Spec...

Open

15188

4.4.3

AI

No

add date

No acceptance criteria for micrographic examination are specified or evidenced for DMV 25.7N in the provided sources. Relevant documents discuss procedures or general requirements but do not define acceptance values or criteria for this requirement. ...

Open

15189

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15190

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) or compliance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-01 - Corrosio...

Open

15191

4.5

AI

No

add date

The acceptance criteria for metallurgical properties are not explicitly specified in the provided documents, so fulfillment cannot be confirmed. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK M...

Open

15192

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria: no pitting at 20X magnification and weight loss < 1.0 g/m², matching the requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

15193

5.1

AI

No

add date

No provided documents contain information on the qualification or certification of NDE personnel to ISO 9712 level II or III, nor on their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-...

Open

15194

5.2

AI

No

add date

No evidence is provided that 100% ultrasonic testing per ASTM E213 or ISO 10893-10 is performed after all processing, or that calibration notches per ASTM E213 Figure 3 are used as specified. Dimensional limits for ultrasonic testing are given, but n...

Open

15195

5.2

AI

No

add date

100% qualitative anti-mixing PMI check is performed on standard production at Montbard using appropriate instruments, fulfilling general NDE acceptance criteria for PMI. Source: DMV_STANDARD_BOOK/12-06-06 - Positive Material Identification (PMI) in M...

Open

15196

5.2

AI

No

add date

No provided document specifies that indications greater than the calibration notch are considered defects requiring rejection or repair, nor do they state the acceptance criteria or disposition policy for such indications as required by the specifica...

Open

15197

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality for the specified product dimensions are confirmed as per the applicable ASTM standards (including ASTM A790/A999), with no deviations or exceptions noted for the requested item or size range. Requiremen...

Open

15198

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

15199

10.0

AI

No

add date

No evidence of an ISO 9001 certified quality-assurance system or certification by a competent EEA body with specific assessment for materials is provided for the manufacturer at the Montbard plant. Source: DMV_STANDARD_BOOK/14-01 - General informatio...

Open

15200

10.1

AI

No

add date

No evidence is provided that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body, as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certif...

Open

15201

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number as required. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

15202

10.2

AI

No

add date

No provided document confirms that documentation traceable to the delivered products (such as SIR205) will be transmitted to TechnipFMC as required. There is no explicit evidence of compliance with the documentation and traceability requirement for T...

Open

15203

10.2

AI

No

add date

A material certificate according to EN 10204 Type 3.1 is issued and validated by Quality Control for mill inspection, which by standard practice includes information required by ASTM A790 and NORSOK M-630. Source: DMV_STANDARD_BOOK/14-03 - Certificat...

Open

15204

10.2

AI

No

add date

None of the reviewed documents provide the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, o...

Open

15205

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Di...

Open

15206

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

15207

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

15208

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15209

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15210

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

15211

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for each heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

15212

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

15213

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), corrosion, and microstructure tests at specified thickness locations per NORSOK MDS D51/ASTM A790. F...

Open

15214

4.2

AI

No

add date

Tensile testing is performed at room temperature per NORSOK MDS D51 Table 4, meeting required properties and referencing ASTM A370 or ISO 6892-1. Hardness testing is also performed. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

15215

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

15216

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement for wall thickness >6mm in both longitudinal and transverse directions. Source: DMV_STANDARD_BOOK/12-03-02 - Impa...

Open

15217

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 and ISO 17781 QL II, meeting the required Charpy V-notch impact properties at -46°C (transverse: avg ≥45 J, single ≥35 J; longitudinal: avg ≥65 J, single ≥50 J) for wall thickness >6 mm, with applicable r...

Open

15218

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

15219

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is explicitly required and matches the specification requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

15220

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

15221

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

15222

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, actual magnification, and scale bar if intermetallic phases are no...

Open

15223

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 includes etching to detect intermetallic stringers, which must be reported, and acceptance is based on CVN and corrosion test results as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

15224

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Zero-tolerance is not guaranteed by the available document...

Open

15225

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

15226

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

15227

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

15228

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

15229

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

15230

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

15231

4.5

AI

No

add date

Corrosion test for DMV 25.7N is performed as per ISO 17781: G48 Method A at 50°C for 24 hours, with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STA...

Open

15232

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montb...

Open

15233

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is performed after all mechanical processing, heat treatments, and straightening, and the dimensional range of the requested pipe is supported. Source: DMV_STANDARD_BOOK/12 - Special Te...

Open

15234

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. For the specified OD, eddy current testing is not feasible, hydrostatic and ultrasonic tests are only available at extra cost, and feasibi...

Open

15235

5.2

AI

No

add date

No provided documentation confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that such NDE acceptance criteria are standardly performed or feasible for the specified pipe dimension a...

Open

15236

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790/A999) for seamless pipe, with no overriding requirements specified by TechnipFMC. Source: 07.01 - General information.doc, 07.03.01 - Tolerances according to ASTM ...

Open

15237

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15238

8.0

AI

No

add date

Marking includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAND...

Open

15239

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

15240

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

15241

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness for the specified size and product form. Source: DMV_STANDARD_BOO...

Open

15242

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO 17782 manufacturing summary or QTR number, are provided and meet the requirement for transmission and traceability to TechnipFMC as per ...

Open

15243

10.2

AI

No

add date

EN 10204 Type 3.1 material certificate will be issued and will include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing...

Open

15244

10.2

AI

No

add date

EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 identification, steel melting practice, heat treatment condition, heat number, chemical analysis, and test results, but only the country of origin of the steel supplier is provided, not th...

Open

15245

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, DMV_STANDARD_BOO...

Open

15246

1.0

AI

No

add date

No evidence that the supplier is qualified to both NORSOK M-650 and ISO 17782 or that QTR/MPCR documentation is available for review. ISO 17782 accreditation is missing for the supplier mentioned for DMV 25.7N. Source: DMV_STANDARD_BOOK/02-04-03 - Di...

Open

15247

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

15248

3.1

AI

No

add date

AOD or equivalent refining is required and used for 100% of production, and chemical analysis complies with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15249

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE 140, as specified in Table 2 and in accordance with ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MD...

Open

15250

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

15251

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

15252

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

15253

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specifi...

Open

15254

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with tensile and hardness properties meeting Table 4 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Diges...

Open

15255

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements for minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW), matching the client specification. Source: DMV_STANDARD_BOOK/02 - S...

Open

15256

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible). The specified pipe dimensions allow for requi...

Open

15257

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

15258

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is required for micrographic examination, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

15259

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

15260

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

15261

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

15262

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

15263

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates below 10µm, which does not meet the stricter requirement of no intermetallic...

Open

15264

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

15265

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

15266

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

15267

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

15268

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 (ASTM A790, NORSOK M-630, M-650/ISO 17782) are fully met, including compliance for destructive and microstructural tests (tensile, impact, corrosion, ferrite, microstructure). ...

Open

15269

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

15270

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destru...

Open

15271

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, performed after all mechanical processing, meeting the requirement for 100% longitudinal defect detection. Source: DMV_STANDARD_BOOK/12 -...

Open

15272

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/ISO 17782 are not fully addressed; only general NDE (hydrostatic, EC, UT) per ASTM A999 is confirmed, with no explicit evidence for NORSOK-specific requirements. For the requested OD (219...

Open

15273

5.2

AI

No

add date

None of the referenced documents explicitly confirm that any indication greater than the calibration notch during NDE is treated as a defect requiring rejection or repair, nor do they specify the acceptance criteria or rejection/repair policy for suc...

Open

15274

6.0

AI

No

add date

Dimensional tolerances are per ASTM A999 as referenced by ASTM A790, with no overriding customer specification or drawing indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM ...

Open

15275

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15276

8.0

AI

No

add date

Marking is performed according to ASTM A790 (§14) and includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Diges...

Open

15277

9.0

AI

No

add date

Weld repairs are explicitly not acceptable as stated in NORSOK MDS D51 Rev 06, §14 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK...

Open

15278

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/...

Open

15279

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

15280

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

15281

10.2

AI

No

add date

ISO 9001 certification is provided and documentation traceable to the products, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO 17782 manufacturing summary or QTR number, is transmitted to TechnipFMC as required by SIR205. Source: DMV_S...

Open

15282

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

15283

10.2

AI

No

add date

NORSOK M-650/ISO 17782 identification, steel melting practice, heat treatment condition, and other documentation requirements are addressed, but the specific steel producer of the starting material is not provided; only the country of origin is state...

Open

15284

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 -...

Open

15285

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782, nor confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

15286

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

15287

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PREN ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 -...

Open

15288

3.2

AI

No

add date

Solution annealing followed by accelerated cooling is performed per ASTM A790; manufacturing and furnace qualification comply with NORSOK M-650/ISO 17782; MST-Tubes is M-650 accredited for DMV 25.7N; free circulation of heating/cooling media is ensur...

Open

15289

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

15290

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for sampling requirements, fulfilling the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03...

Open

15291

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, per ASTM A790 and NORSOK requi...

Open

15292

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and maximum hardness properties of Table 4. Hardness testing is also performed per ASTM...

Open

15293

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (750 MPa), yield strength (550 MPa), elongation (25%), and maximum hardness (310 HBW) as required by NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

15294

4.3

AI

No

add date

Pipe wall thickness (18.26 mm) exceeds minimum required for Charpy V-notch testing per ASTM (6.35 mm) and ISO (8.74 mm); testing per ASTM A370 or ISO 148-1 is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03...

Open

15295

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, with minimum absorbed energy values for transverse and longitudinal directions, and the specified pipe dimensions allow for required testing directions and specimen...

Open

15296

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

15297

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

15298

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

15299

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781, with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDA...

Open

15300

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

15301

4.4.2

AI

No

add date

Micrographic examination requires reporting of centerline intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

15302

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is...

Open

15303

4.4.3

AI

No

add date

Ferrite content is checked per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite determination per ASTM E562 or E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

15304

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

15305

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15306

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available data. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

15307

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15308

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

15309

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in...

Open

15310

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, with pipe dimensions within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

15311

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/NORSOK M-650/ISO 17782 are not fully met: provided information only covers ASTM NDE, not NORSOK-specific requirements; eddy current testing is not feasible for OD 219.1 mm at Montbard; hy...

Open

15312

5.2

AI

No

add date

None of the referenced documents explicitly confirm that any indication greater than that produced by the calibration notch is treated as a defect and that such pipes are rejected or repaired, as required by the specification. Source: Digest ASTM A 7...

Open

15313

6.0

AI

No

add date

Dimensional tolerances for the specified pipe are per ASTM A790 and referenced ASTM A999, with no overriding TechnipFMC part report or drawing indicated, fulfilling the requirement that tolerances follow the applicable ASTM standard unless otherwise ...

Open

15314

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORS...

Open

15315

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

15316

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15317

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

15318

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system as specified in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

15319

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling supplier qualification documentation per SIR1...

Open

15320

10.2

AI

No

add date

ISO 9001 certification is provided and documentation traceable to the products, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, is transmitted to TechnipFMC as required by SIR205. Source: DMV_ST...

Open

15321

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification summary. Certificate...

Open

15322

10.2

AI

No

add date

Most documentation and certification requirements are addressed except for the 'Steel producer of the starting material,' which is not fully fulfilled as only the country of origin is provided, not the actual producer name. There is also no evidence ...

Open

15323

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, with explicit coverage of mechanical, chemical, and testing requirements for duplex stainless steel pipes. ...

Open

15324

1.0

AI

No

add date

No evidence is provided that the supplier is qualified in accordance with both NORSOK M-650 and ISO 17782 for the exact product supplied, nor is the availability of the full Qualification Test Record/MPCR for review by TechnipFMC confirmed. Source: D...

Open

15325

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650. Compliance with NORSOK MDS D51 Rev. 6 is confirmed. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

15326

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis for DMV 25.7N complies with Table 2 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest ...

Open

15327

3.1

AI

No

add date

DMV 25.7N (UNS S32760) is manufactured according to NORSOK M-650 qualified procedures, with accreditation for WT up to 31.75 mm, covering the requested WT of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

15328

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15329

3.2

AI

No

add date

Heat treatment is solution annealing followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782 and procedures ensuring free circulation of heating and cooling media around each p...

Open

15330

4.1

AI

No

add date

No evidence that impact, tensile, hardness, corrosion testing, and microstructure examinations are performed for each heat and heat treatment lot as defined in ASTM A790; only partial or unrelated testing information is provided. Source: DMV_STANDARD...

Open

15331

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

15332

4.1

AI

No

add date

Tensile test direction per ASTM A790 is confirmed, but CVN impact test direction and sampling, as well as other specified test methods and locations, are not fully addressed or confirmed for seamless pipes prolongation samples as required in the tabl...

Open

15333

4.2

AI

No

add date

Tensile testing is performed at room temperature with criteria meeting or exceeding Table 4 (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%), in accordance with ASTM A370 or ISO 6892-1, and maximum hardness is verified as required for DMV 25.7N. Source: DMV_...

Open

15334

4.2

AI

No

add date

Mechanical property values required (tensile strength, yield strength, elongation, hardness) are not confirmed in the provided sources; referenced documents either lack the specific values or address different grades with lower properties. Source: DM...

Open

15335

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the ordered pipe (NPS 8, 219.1mm OD, 18.26mm WT), as it exceeds the minimum wall thickness required for both standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-0...

Open

15336

4.3

AI

No

add date

Pipe dimensions allow for both longitudinal and transverse Charpy V-notch specimens; impact property requirements of Table 5 can be fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02...

Open

15337

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation and examination according to ISO 17781 or the specified etching procedures for 25 Cr Duplex stainless steels. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/1...

Open

15338

4.4.1

AI

No

add date

No information is provided confirming the use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination; only grain size measurement for austenitic materials is discussed, without reference t...

Open

15339

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic phases; isolated phases are permitted if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

15340

4.4.2

AI

No

add date

No information or procedures are provided regarding the detection, recording, or micrographic documentation (at 400x minimum) of intermetallic phases; the requirement is not addressed. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DM...

Open

15341

4.4.2

AI

No

add date

No evidence that a representative micrograph at or near mid-wall thickness is recorded and reported at 400x minimum magnification with actual magnification and scale bar when intermetallic phases are not detected. Partial mention of 400x photos, but ...

Open

15342

4.4.2

AI

No

add date

No provided documentation addresses the reporting of centerline intermetallic stringers or links product acceptance to CVN and corrosion test results in such cases. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I.doc, DMV_STANDAR...

Open

15343

4.4.2

AI

No

add date

NORSOK MDS D41 Rev 06 and D51 Rev 06 allow isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not meet the stricter requirement of prohibiting all intermetallic phases and/or precipitates if CVN test...

Open

15344

4.4.3

AI

No

add date

No information is provided confirming ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781; only grain size examination is discussed, not ferrite content determination. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size...

Open

15345

4.4.3

AI

No

add date

No provided document addresses acceptance criteria for micrographic examination or metallurgical properties for the Montbard plant; relevant procedures are either not mentioned or only applicable to other locations or standards. Source: DMV_STANDARD_...

Open

15346

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15347

4.5

AI

No

add date

No specific acceptance criteria for metallurgical properties are provided or detailed in the referenced documents, so the requirement cannot be validated or fulfilled based on the available information. Source: DMV_STANDARD_BOOK/02-03-01 - Digest AST...

Open

15348

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m² is specified, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

15349

5.1

AI

No

add date

No evidence provided regarding qualification or certification of NDE personnel to ISO 9712 level II or III, or their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01, DMV_STANDARD_BOOK/12-02-02, DMV_STANDARD_BOOK/...

Open

15350

5.2

AI

No

add date

No explicit confirmation that 100% ultrasonic testing per ASTM E213 or ISO 10893-10, including specified calibration notches and timing after all processing steps, is performed at Montbard. Only dimensional feasibility for ultrasonic testing is provi...

Open

15351

5.2

AI

No

add date

Dye penetrant testing is provided for tube ends and bevels on request, matching the specification as there is no requirement for full-length testing or a specific request for it. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive ...

Open

15352

5.2

AI

No

add date

No provided document confirms that pipes with NDE indications greater than the calibration notch are rejected or repaired as required; acceptance criteria and disposition policy are not explicitly addressed for the specified product and dimension at ...

Open

15353

6.0

AI

No

add date

Dimensional tolerances for the requested product are confirmed as per the applicable ASTM standards (including ASTM A790/A999) for OD, WT, and ovality, with no deviations or special tolerances indicated in the client inquiry or documentation. Source:...

Open

15354

7.0

AI

No

add date

Pipes are required to be pickled or bright annealed according to ASTM A790 and NORSOK MDS S01, fulfilling the requirement for finished pipes to be white pickled or bright annealed. Source: ASTM A790, NORSOK MDS S01.

Open

15355

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/13 - Marking/13-02 - Standard marking feasibility/13-02-01 - Standard marking feasibility - Montbard plant/13...

Open

15356

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

15357

10.0

AI

No

add date

No evidence of an ISO 9001 or equivalent quality-assurance system certified by a competent EEA body is provided for the Montbard plant or manufacturer. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STANDARD_BOOK/14-03 - Certification...

Open

15358

10.1

AI

No

add date

No evidence provided that the manufacturer has an ISO 9001 certified quality-assurance system as required by the specification. Source: DMV_STANDARD_BOOK/14 - Inspection - Documentation/14-03 - Certification/14-03 - Certification Montbard plant/14-03...

Open

15359

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV25.7N up to WT = 31.75 mm, and the EN 10204 3.1 certificate will include the NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, demonstrating qualification for the si...

Open

15360

10.2

AI

No

add date

There is no explicit confirmation that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC as specified. No evidence of a process ensuring this requirement is fulfilled is provided. Source: DMV_STANDARD_BO...

Open

15361

10.2

AI

No

add date

Material certificate is issued according to EN 10204 Type 3.1 and validated by Quality Control for mill inspection; compliance with ASTM A790 and NORSOK M-630 information inclusion is not explicitly confirmed but certificate type and process are comp...

Open

15362

10.2

AI

No

add date

No provided documents contain the required documentation or certification details such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or test results for metallu...

Open

15363

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements. Manufacturing is M-650 qualified. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev ...

Open

15364

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR availability for review as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15365

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), matching the requested grade and wall thickness (18.26 mm). The manufacturing process follows M-650 (or ISO 17782) qualified procedures, fulfilling the requirement ...

Open

15366

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits and PREN requirements specified in Table 2, as confirmed by both ASTM A790 and NORSOK MDS D51 Rev 06 digests. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15367

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are placed to ensure free ...

Open

15368

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

15369

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

15370

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes per ASTM A790/NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure tests at specified thickness locati...

Open

15371

4.2

AI

No

add date

Tensile testing is performed in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for DMV 25.7N as required by NORSOK MDS D51 and ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

15372

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15373

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse average/single values of 45 J/35 J, and longitudinal average/single values of 65 J/50 J if transverse is not possible. The...

Open

15374

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, with etching using 20-40% NaOH or KOH after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

15375

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

15376

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

15377

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

15378

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

15379

4.4.2

AI

No

add date

Micrographic examination requirements specify that intermetallic phases must be reported and acceptance is based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers reporting and acceptance criteria. Sou...

Open

15380

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates, which does not meet the stricter client requirement of not permitting any i...

Open

15381

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

15382

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance is based on im...

Open

15383

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS ...

Open

15384

4.5

AI

No

add date

Applicable standards are referenced but there is no explicit confirmation that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or included in the documentation provided. Source: DMV_STANDARD_BOOK/12-03-...

Open

15385

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content...

Open

15386

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781: G48 Method A at 50°C for 24h, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and complies with these requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

15387

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15388

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

15389

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 can be performed after all processing steps, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non...

Open

15390

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled; standard NDE methods (hydrostatic, EC, UT) are only available at extra cost or are not feasible for the specified pipe size at Montbard, and n...

Open

15391

5.2

AI

No

add date

None of the relevant documents explicitly state that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair, nor do they confirm that NDE will be performed as standard for the specified di...

Open

15392

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no deviations or special tolerances specified in the customer request or context. Requirement is fulfilled as tolerances default to ASTM un...

Open

15393

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15394

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

15395

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

15396

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

15397

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

15398

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified ...

Open

15399

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

15400

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and covering required details such as heat treatment, steel manufacturer, melting and refining practice, and ...

Open

15401

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C, including minimum absorbed energy values and sub-size reduction factors. The specified pipe dimensions allow for required transverse Charpy V-notch testing. Source:...

Open

15402

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, actual chemical analysis, solution annealing parameters, or results of required metallurgical and non-destructive tes...

Open

15403

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, DMV_STANDARD_BOOK/02-04-03 - D...

Open

15404

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N but not to ISO 17782, as explicitly required. No evidence of QTR/MPCR documentation availability. Requirement not fully fulfilled. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D...

Open

15405

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - ...

Open

15406

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15407

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15408

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

15409

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for one set per heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

15410

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for sampling, fulfilling the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

15411

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specified thickness loc...

Open

15412

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, with DMV 25.7N meeting or exceeding the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

15413

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

15414

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible and fulfilled for the specified pipe dimensions, which exceed the minimum wall thickness required for testing. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.do...

Open

15415

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, DMV_STANDARD_B...

Open

15416

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants and electrolytic etching after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/...

Open

15417

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is explicitly required for micrographic examination as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

15418

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

15419

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases as required. Source: DMV_STAN...

Open

15420

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected, fulfilling the requirem...

Open

15421

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 requires reporting of intermetallic phases, with acceptance based on CVN and corrosion test results if such phases are present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STAN...

Open

15422

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size, so the requirement is not fully me...

Open

15423

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

15424

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

15425

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

15426

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781; neither standard nor test is mentioned or specified in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plan...

Open

15427

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, as well as manufacturing and qualification requirements. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

15428

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

15429

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

15430

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions and is performed after all mechanical processing. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 ...

Open

15431

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/ISO 17782 are not fully met; only partial NDE methods (hydrostatic, EC, UT) are available, with limitations for the specified OD and length, and full compliance with NORSOK/ASTM requireme...

Open

15432

5.2

AI

No

add date

None of the referenced documents explicitly state that any indication greater than that produced by the calibration notch is a defect requiring rejection or repair, nor do they confirm the acceptance criterion or standard NDE feasibility for the spec...

Open

15433

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no deviations or overrides specified by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312-01a A 376...

Open

15434

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15435

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

15436

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Diges...

Open

15437

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

15438

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

15439

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demonstration for th...

Open

15440

10.2

AI

No

add date

No evidence that documentation traceable to the products (SIR205) will be transmitted to TechnipFMC as required; only general certification and documentation practices are described without confirming specific transmission and traceability to the cli...

Open

15441

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

15442

10.2

AI

No

add date

NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition are confirmed to be included in the EN 10204 3.1 certificate, but the specific steel producer is not provided (only country of origin), and there is no eviden...

Open

15443

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification and all required mechanical, chemical, and testing requirements met, as indicated in the specification and digest references. Source: ...

Open

15444

1.0

AI

No

add date

Supplier is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to certain wall thicknesses) but not accredited to ISO 17782, as required. No evidence of QTR/MPCR availability or full compliance with the essential variables and limitations specifie...

Open

15445

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N within the required wall thickness range, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_...

Open

15446

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15447

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed by supplier certification and heat analysis. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03...

Open

15448

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

15449

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined by ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

15450

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, fulfilling the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/...

Open

15451

4.1

AI

No

add date

All required tests (tensile, hardness, CVN, corrosion, microstructure) are performed on seamless pipes per NORSOK MDS D51 and ASTM A790, with correct test directions and thickness locations. For the specified pipe dimensions, transverse CVN specimens...

Open

15452

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

15453

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

15454

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact ...

Open

15455

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C, with minimum absorbed energy values of 45 J (transverse average), 35 J (transverse single), 65 J (longitudinal average), and 50 J (longitudinal single). The specified...

Open

15456

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, with specified etchants for intermetallic phases and ferrite balance applied after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

15457

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution, as specified in ISO 17781 Appendix B, is used to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

15458

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

15459

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

15460

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report at actual magnification and with a scale bar, fulfilling the requirement if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/...

Open

15461

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

15462

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size. No other relevant information provided support...

Open

15463

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

15464

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

15465

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

15466

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or confirmed in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

15467

4.5

AI

No

add date

DMV 25.7N meets all relevant metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content. Source: DMV...

Open

15468

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

15469

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

15470

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 or ISO 10893-10 is feasible and standards-compliant for the specified pipe dimensions; calibration is expected to follow ASTM E213 Figure 3 as required since the standard i...

Open

15471

5.2

AI

No

add date

NDE per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 is not confirmed; only ASTM A790/A999 NDE is detailed. For OD 219.1 mm, Eddy current testing is not feasible, and hydrostatic/ultrasonic tests incur extra cost. Full-length dye penetrant testing...

Open

15472

5.2

AI

No

add date

No provided documentation confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair, nor that the specified NDE acceptance criterion is applied as standard for the requested ...

Open

15473

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Zero-tolerance is not guaranteed by the available document...

Open

15474

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A999 for ASTM A790 pipe) unless otherwise specified, with no override indicated by TechnipFMC. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_...

Open

15475

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15476

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

15477

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

15478

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

15479

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

15480

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling supplier qualification documentation requirem...

Open

15481

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 manufacturing summary or QTR number, are provided as required by SIR205 and section 10.0 of the specification. Source: DMV_STANDARD...

Open

15482

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and validated by Quality Control, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification summary). So...

Open

15483

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of metallurgical and non-de...

Open

15484

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all supplementary requirements. Manufacturing is M-650 qualified for the specified grade and wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Dige...

Open

15485

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782, and there is no confirmation of QTR/MPCR availability as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15486

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

15487

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15488

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PRE ≥ 40, as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15489

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15490

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

15491

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

15492

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

15493

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests, with specified locations and directions, is fulfilled for DMV 25.7N per ...

Open

15494

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with material meeting the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

15495

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

15496

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for 18.26mm wall thickness and 219.1mm OD pipe in both longitudinal and transverse directions. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

15497

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for required transverse testing. Source: DMV_STANDA...

Open

15498

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching for intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and examination in accordance ...

Open

15499

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect intermetallic phases, in accordance with ISO 17781, is required for micrographic examination, fulfilling the requirement for suitable etchants as listed in ISO 17781 Appendix B to show ferrite balance and in...

Open

15500

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

15501

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

15502

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, matching the requirement for a representative micrograph at or near mid-wall thickness, at 400x minimum, with actual magnification and scale bar reported ...

Open

15503

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

15504

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

15505

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

15506

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

15507

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

15508

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

15509

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

15510

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

15511

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and the requested pipe dimensions are within capability range. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02...

Open

15512

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD (219.1 mm), eddy current testing is not feasible, and hydrostati...

Open

15513

5.2

AI

No

add date

No provided documentation confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that such NDE acceptance criteria are standard or feasible for the specified pipe dimensions at Montbard....

Open

15514

6.0

AI

No

add date

Dimensional tolerances are confirmed as per the applicable ASTM standard (ASTM A790 referencing ASTM A999) for the specified pipe dimensions, with no alternative requirements stated in the context. Source: DMV_STANDARD_BOOK/07-01 - General informatio...

Open

15515

7.0

AI

No

add date

ASTM A790 (6.1.3) and NORSOK MDS D51 (§13) both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15516

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 §16.1, both requiring full traceability to melt and heat treatment lot. Marking methods include heat number and DMV lot number, ensuring compliance for 100% of the pipes. Source: DMV_STAND...

Open

15517

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

15518

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N but not to ISO 17782; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15519

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

15520

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

15521

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demonstration for th...

Open

15522

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

15523

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant standards and qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D...

Open

15524

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all metallurgical and no...

Open

15525

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, including chemical, mechanical, manufacturing, and testing requirements. M-650 qualification is confirmed for DMV 25.7N. So...

Open

15526

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782; no confirmation of QTR/MPCR availability. Requirement for NORSOK M-650/ISO 17782 qualification and documentation is not fully met. Source: DMV_STANDARD_BOOK/02-04-03 - Digest N...

Open

15527

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, with manufacturing process qualified per NORSOK M-650 (or ISO 17782) and meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

15528

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev...

Open

15529

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as per Table 2 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51...

Open

15530

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

15531

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

15532

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with frequency and method matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

15533

4.1

AI

No

add date

Test sampling for seamless pipes per ASTM A790 and NORSOK MDS D51, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions, i...

Open

15534

4.2

AI

No

add date

Tensile testing is performed at room temperature in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

15535

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

15536

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, which exceed the minimum wall thickness required for standard transverse specimens. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - D...

Open

15537

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements, including Charpy V-notch testing at -46°C with minimum absorbed energies (45 J average, 35 J single transverse; 65 J average, 50 J single longitudinal if transverse not possible), and ...

Open

15538

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with the specified etchants after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

15539

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

15540

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

15541

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

15542

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

15543

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

15544

4.4.2

AI

No

add date

The referenced documents either do not address the prohibition of intermetallic phases/precipitates when CVN testing cannot be completed, or they allow isolated precipitates, which does not meet the stricter client requirement of not permitting any i...

Open

15545

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

15546

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), in compliance with NORSOK MDS D51/ASTM...

Open

15547

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

15548

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

15549

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, chemical composition, ferrite content, corrosion resistance, impact, and microstructure, and is M-650 qualifi...

Open

15550

4.5

AI

No

add date

Corrosion test for DMV 25.7N is performed per ISO 17781: G48 Method A at 50°C for 24 hours, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/...

Open

15551

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement is not fulfilled based on the available information. Sou...

Open

15552

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, performed after all mechanical processing, as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12...

Open

15553

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled. Provided information only covers ASTM A790/A999 NDE, and for the specified OD (219.1 mm), eddy current testing is not feasible, hydrostatic an...

Open

15554

5.2

AI

No

add date

None of the relevant documents explicitly confirm that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor do they confirm that the required NDE methods and acceptance criteria ...

Open

15555

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790/A999) for the specified pipe dimensions, with no deviations or special customer tolerances indicated, fulfilling the requirement unless otherwise stated by the cus...

Open

15556

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, matching the requirement. Source: ASTM A 790.docx, NORSOK MDS D51 Rev 06.docx

Open

15557

8.0

AI

No

add date

Marking per ASTM A790 and plant marking methods include heat number and lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02...

Open

15558

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

15559

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

15560

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, meeting the requirement. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

15561

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

15562

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

15563

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

15564

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certification ...

Open

15565

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all required metallurgi...

Open

15566

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all referenced mechanical, chemical, and testing requirements. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

15567

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to 31.75 mm WT, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

15568

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15569

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements, and heat analysis is performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A...

Open

15570

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

15571

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per lot as defined in ASTM A790, fulfilling the requirement for each heat and heat treatment lot. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

15572

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

15573

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specifi...

Open

15574

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, meeting the tensile and maximum hardness properties of Table 4 for DMV 25.7N. Hardness testing is also performed as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

15575

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's Table 4 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

15576

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible as the pipe wall thickness exceeds the minimum required by the standards. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

15577

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible), with reduction factors for sub-size specimens...

Open

15578

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

15579

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination and fulfills the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

15580

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

15581

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

15582

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

15583

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

15584

4.4.2

AI

No

add date

The referenced documents do not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed; isolated precipitates below 10µm are allowed, which does not meet the stricter client requirement of zero tolerance in such ca...

Open

15585

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 ...

Open

15586

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

15587

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15588

4.5

AI

No

add date

No explicit evidence of ASTM G48 Method 'A' (50˚C, 24h) corrosion testing in accordance with ISO 17781 is provided or referenced in the listed standards or documents. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

15589

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, with microstructure acceptance referenced to ISO 17781. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

15590

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

15591

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

15592

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available and applicable for the specified pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultrasonic testing...

Open

15593

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requested OD (219.1 mm), standard NDE (eddy current, ultrasonic, hydrostatic) is not a...

Open

15594

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, and standard NDE for the requested OD is not feasible at Montbard for this size and method. So...

Open

15595

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790/A999) for the specified pipe, with no overriding requirements indicated in the customer specification or drawing. Source: DMV_STANDARD_BOOK/07-01 - General informa...

Open

15596

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15597

8.0

AI

No

add date

Marking includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAND...

Open

15598

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required by NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MD...

Open

15599

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

15600

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

15601

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

15602

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products being delivered as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

15603

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 manufacturing summary/QTR number. Source: DMV_ST...

Open

15604

10.2

AI

No

add date

No provided documentation includes all required details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, actual chemical analysis, solution annealing parameters, or specific metallurgica...

Open

15605

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the specification digest and the customer specification listing 'A790 NORSOK'. Manufacturing is M-650 qualified for the required...

Open

15606

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability or full compliance with essential variables and limitations per NORSOK M-650/ISO 17782 is provided. Source: DMV_ST...

Open

15607

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, with manufacturing process qualified to NORSOK M-650 (or ISO 17782), and compliance with NORSOK M-630 MDS D51 Rev. 6 is confirmed. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

15608

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15609

3.1

AI

No

add date

DMV 25.7N (UNS S32760) chemical composition complies with Table 2 of ASTM A790 and NORSOK MDS D51 Rev 06, including PREN ≥ 40 and all specified element limits for S32760. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev...

Open

15610

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

15611

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

15612

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and direct reference to the table for test specimen sampling as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

15613

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes meets NORSOK MDS D51/ASTM A790 requirements: tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations. F...

Open

15614

4.2

AI

No

add date

Tensile testing is performed in accordance with ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 as required for DMV 25.7N (UNS S32760). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

15615

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, fulfilling the client's mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

15616

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in...

Open

15617

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for required transverse testing. Source: DM...

Open

15618

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements at -46°C (transverse: 45/35 J, longitudinal: 65/50 J) for thickness >6mm, and the specified pipe dimensions allow for required testing directions and specimen sizes. Source: DMV_STANDAR...

Open

15619

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

15620

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

15621

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

15622

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs are included and recorded as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

15623

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

15624

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

15625

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully fulfilled. So...

Open

15626

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 ...

Open

15627

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781, including etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance is based on im...

Open

15628

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in accordance with ISO 17781 and ASTM E1245, and DMV 25.7N complies with this requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02...

Open

15629

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

15630

4.5

AI

No

add date

DMV 25.7N complies with all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including destructive, micrographic, ferrite, corrosion, and impact tests, with accredited manufacturing and qualification processes. Source: DMV_STANDARD_BOOK/0...

Open

15631

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A @ 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and complies with these requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

15632

5.1

AI

No

add date

No information is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source:...

Open

15633

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available after all processing, and the dimensional range is supported. Reference notches per ASTM E213 are included. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

15634

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790, NORSOK M-630 MDS D51, and NORSOK M-650/ISO 17782 are not fully addressed. Provided information only covers ASTM A790/A999 NDE, omits NORSOK-specific requirements, and details destructive tests only. For OD 219.1...

Open

15635

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair; NDE acceptance criteria and required testing are not explicitly stated or confirmed for the sp...

Open

15636

6.0

AI

No

add date

Dimensional tolerances for the specified pipe are per the applicable ASTM standard (ASTM A999 as referenced by ASTM A790), with no deviations or special tolerances indicated in the customer request or context. Source: DMV_STANDARD_BOOK/07-01 - Genera...

Open

15637

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15638

8.0

AI

No

add date

Marking per ASTM A790 §16 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STAND...

Open

15639

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

15640

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

15641

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

15642

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demons...

Open

15643

10.2

AI

No

add date

Certification to EN 10204 type 3.1 is provided, including heat treatment, steel manufacturer, melting/refining practice, NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, and traceability, fulfilling the requirement for documentation to be t...

Open

15644

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control for mill inspection and referencing relevant standards and qualifications. Source: DMV_STANDARD_BOOK/02-04-03 ...

Open

15645

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

15646

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781 Appendix B, is specified and matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

15647

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

15648

10.2

AI

No

add date

No provided document contains all required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, full chemical (ladle) analysis, solution annealing tem...

Open

15649

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, including chemical, mechanical, manufacturing, and testing requirements for 25 Cr Duplex stainless steel seamless pipes. So...

Open

15650

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N but not to ISO 17782, as explicitly required. No evidence provided for QTR/MPCR availability for review by TechnipFMC as per the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

15651

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to 31.75 mm WT, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

15652

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition complies with Table 2 requirements for DMV 25.7N seamless pipe per ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - ...

Open

15653

3.1

AI

No

add date

DMV 25.7N (UNS S32760) chemical composition matches the requirements of Table 2 and complies with ASTM A790 and NORSOK MDS D51 Rev 06, including PREN ≥ 40 and all specified element limits. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest ...

Open

15654

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling (including water quenching) per ASTM A790, with manufacturing process and furnaces qualified to NORSOK M-650/ISO 17782. Heat treatment and compliance are certified. Source: DMV_STANDARD_BOOK...

Open

15655

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, with a frequency of 1/lot for each test type, fulfilling the requirement. Source: DMV_STAND...

Open

15656

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

15657

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is performed as required. For the ordered pip...

Open

15658

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, meeting the tensile and maximum hardness properties of Table 4, with compliance to NORSOK MDS D51 confirmed. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

15659

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

15660

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement for wall thickness and testing standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive test...

Open

15661

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

15662

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

15663

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

15664

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

15665

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, but does not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed, as required by the client specification. Requirement not full...

Open

15666

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

15667

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching methods, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and...

Open

15668

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

15669

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

15670

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 06, including destructive, micrographic, corrosion tests, ferrite content, heat treatment, and manufacturing process requirements. Microstructure acceptance i...

Open

15671

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

15672

5.1

AI

No

add date

No evidence is provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destr...

Open

15673

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions and is performed after all mechanical processing, meeting the requirement for 100% longitudinal defect detection. Source: DMV_STANDARD_BOO...

Open

15674

5.2

AI

No

add date

NDE per ASTM A790 and NORSOK M-630 MDS D51 is not fully fulfilled: eddy current testing is not feasible for the required OD at Montbard, and hydrostatic/ultrasonic testing is only available at extra cost. No evidence of NORSOK-specific NDE acceptance...

Open

15675

5.2

AI

No

add date

No evidence that indications greater than the calibration notch are treated as defects requiring rejection or repair; NDE acceptance criteria are not specified and eddy current testing is not feasible for the requested OD at Montbard, limiting defect...

Open

15676

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and referenced ASTM A999, with no override in the client specification or drawing, fulfilling the requirement that tolerances follow the applicable ASTM standard unless otherwise stated. Source: DMV_STANDARD_B...

Open

15677

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15678

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

15679

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

15680

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

15681

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

15682

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

15683

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 manufacturing summary/QTR number. ...

Open

15684

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice and refining method, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the actual steel produce...

Open

15685

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all referenced mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STA...

Open

15686

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N but not to ISO 17782; no evidence provided for full qualification to both standards or availability of QTR/MPCR documentation for review as required by the specification. Source: DMV_STAN...

Open

15687

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

15688

3.1

AI

No

add date

AOD or equivalent refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15689

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the specified limits in Table 2 and is confirmed by supplier certification and heat analysis for DMV material. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

15690

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification will state heat treatment condition as per ASTM A790. Pipes are processed to ensure ...

Open

15691

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

15692

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

15693

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified locations and directions, is fulfilled per NORSOK MDS D51/AS...

Open

15694

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 as required by NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

15695

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

15696

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, meeting the requirement for impact testing as per Table 5. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-...

Open

15697

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C (transverse: 45 J avg/35 J single, longitudinal: 65 J avg/50 J single if transverse not possible). The specified pipe dimensions allow for required transverse Charpy ...

Open

15698

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

15699

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution for detecting ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B requirements for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

15700

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

15701

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

15702

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

15703

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

15704

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: ASTM A790, NORSOK MDS D51 Rev 6

Open

15705

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

15706

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching methods, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact...

Open

15707

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

15708

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced; requirement cannot be validated as fulfilled based on available information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion te...

Open

15709

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including destructive and microstructural tests, manufacturing, heat treatment, and qualification procedures. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

15710

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

15711

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructi...

Open

15712

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects is performed in accordance with ASTM E213 and ISO 10893-10 after all processing steps, and the dimensional range is supported. Calibration is per ASTM E213, covering reference notch requirements. Sourc...

Open

15713

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially addressed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are met. For the requested OD of 219.1 mm, eddy current testing is not feasibl...

Open

15714

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor that the required NDE will be performed as standard for the specified pipe size and grade. Sourc...

Open

15715

6.0

AI

No

add date

Dimensional tolerances are per applicable ASTM standard (A790/A999) as required, with no overriding specifications from TechnipFMC indicated. Source: 07.01 - General information.doc, 07.03.01 - Tolerances according to ASTM A 312-01a A 376-02a A ...

Open

15716

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15717

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

15718

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly states that weld repairs are not acceptable, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15719

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

15720

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

15721

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification dem...

Open

15722

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 manufacturing summary or QTR number, are provided and fulfill the requirement for documentation traceable to the products and trans...

Open

15723

10.2

AI

No

add date

Certification is provided to EN 10204 Type 3.1 and includes all information required by ASTM A790 and NORSOK M-630, with compliance validated by Quality Control and reference to M-650/ISO17782 qualification. Source: DMV_STANDARD_BOOK/02-04-03 - Diges...

Open

15724

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and full metallurgical and non-destr...

Open

15725

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified for the specified wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

15726

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence provided for QTR/MPCR availability or full compliance with essential variables and documentation requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Dige...

Open

15727

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, with manufacturing process qualified per NORSOK M-650 or ISO 17782 and meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

15728

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15729

3.1

AI

No

add date

Available documents do not confirm that DMV 25.7N meets all individual maximum/minimum chemistry limits for S32760 as specified in NORSOK M-630 MDS D51; only ASTM A790 chemistry or general PREN compliance is referenced, not the full NORSOK chemistry ...

Open

15730

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

15731

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

15732

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

15733

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, in accordance with ASTM A790 an...

Open

15734

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

15735

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, fulfilling the client's mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

15736

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, fulfilling the requirement for wall thickness and testing standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive test...

Open

15737

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible), with sub-size reduction factors. The specifie...

Open

15738

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching for intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and examination in accordance ...

Open

15739

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

15740

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

15741

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

15742

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

15743

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK/0...

Open

15744

4.4.2

AI

No

add date

No provided documentation prohibits all intermetallic phases and/or precipitates when CVN testing cannot be completed; the closest reference allows isolated precipitates below 10µm, which does not meet the stricter client requirement. Source: DMV_STA...

Open

15745

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

15746

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosio...

Open

15747

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS ...

Open

15748

4.5

AI

No

add date

Corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is not explicitly referenced or evidenced in the available documentation to confirm fulfillment of the requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests...

Open

15749

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content...

Open

15750

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, meeting the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² for corrosion testing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

15751

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

15752

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non des...

Open

15753

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not explicitly addressed. For the requested OD (219.1 mm), eddy current testing is only feasible with a multi-elements probe (not differential encircling coils), an...

Open

15754

5.2

AI

No

add date

None of the provided documents explicitly confirm that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor do they confirm that the required NDE will be performed as standard fo...

Open

15755

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no evidence of a deviation or special tolerance request in the customer specification or drawing. Source: DMV_STANDARD_BOOK/07-01 - General...

Open

15756

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15757

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot, and standard marking methods at Montbard plant include heat number and lot number as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DM...

Open

15758

9.0

AI

No

add date

Weld repairs are explicitly not acceptable as per NORSOK MDS D51 Rev 06, §14. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15759

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for a quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

15760

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

15761

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

15762

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

15763

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

15764

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or actual metallurgical and non-destru...

Open

15765

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the item table and confirmed by the digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04...

Open

15766

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N but not to ISO 17782; no evidence provided for QTR/MPCR availability or full compliance with both standards as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06....

Open

15767

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

15768

3.1

AI

No

add date

AOD or equivalent refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15769

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. The chemical composition table matches the standard and compliance is confirmed for the proposed grade. Sourc...

Open

15770

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured...

Open

15771

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

15772

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

15773

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at the spe...

Open

15774

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and material meets the tensile and maximum hardness properties of Table 4 as required for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

15775

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

15776

4.3

AI

No

add date

Supplied wall thickness exceeds minimum required for Charpy V-notch testing as per ASTM A370 or ISO 148-1; requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact ...

Open

15777

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C (transverse: 45J/35J, longitudinal: 65J/50J) with applicable sub-size reduction factors; the specified pipe dimensions allow both longitudinal and transverse impact te...

Open

15778

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching for intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and examination in accordance ...

Open

15779

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

15780

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

15781

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

15782

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

15783

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

15784

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. No source fully prohibits intermet...

Open

15785

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

15786

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

15787

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

15788

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

15789

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782 qualification, including chemical composition, mechanical properties, impact, corrosion, microstructure, and f...

Open

15790

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m²; DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

15791

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

15792

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is confirmed, applicable after all mechanical processing, and the equipment supports the specified pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructiv...

Open

15793

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed; only ASTM A790/A999 NDE is detailed. For OD 219.1 mm, eddy current testing is not feasible, hydrostatic and ultrasonic tests are only available at extra co...

Open

15794

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor confirms that the required NDE will be performed as standard for the requested ...

Open

15795

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and ASTM A999 as required, with no overriding specifications from TechnipFMC. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a A ...

Open

15796

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15797

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes heat number, lot number, and other traceable information, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

15798

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

15799

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

15800

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

15801

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size ...

Open

15802

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

15803

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications and plant documentation. Source: DMV_STANDARD_BOOK/02-04-03 - Dig...

Open

15804

10.2

AI

No

add date

EN 10204 3.1 certificates will include NORSOK M-650/ISO 17782 identification, steel melting practice, refining method, heat treatment condition, heat number, chemical analysis, and test results, but only the country of origin of the steel supplier is...

Open

15805

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

15806

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: ASTM A790, NORSOK MDS D51 Rev 6

Open

15807

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability for review or full compliance with essential variables and limitations per the specification. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

15808

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

15809

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15810

3.1

AI

No

add date

Chemical composition for UNS S32760 matches the requirement table and is confirmed to conform to ASTM A790 Table 2. Heat analysis is performed per heat as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dige...

Open

15811

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

15812

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

15813

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

15814

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure, is performed per NORSOK MDS D51/ASTM A790. For the ordered pipe (OD 219.1 mm, ...

Open

15815

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the specified tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produc...

Open

15816

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness per ASTM A790, fulfilling the client's mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

15817

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and meets the requirements of ASTM A370 or ISO 148-1. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in M...

Open

15818

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; pipe dimensions allow for required transverse testing. Source: DMV_STANDA...

Open

15819

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

15820

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination and fulfills the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

15821

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

15822

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

15823

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

15824

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

15825

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm, while the requirement does not permit any intermetallic phases or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully fulfilled. Sourc...

Open

15826

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

15827

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

15828

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

15829

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50°C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

15830

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content...

Open

15831

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

15832

5.1

AI

No

add date

No evidence provided that NDE personnel are qualified and certified to ISO 9712 level II or III or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard...

Open

15833

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, performed after all mechanical processing, fulfilling the requirement for 100% longitudinal defect testing. Source: DMV_STANDARD_BOOK/12 ...

Open

15834

5.2

AI

No

add date

NDE per ASTM A790/A999 is detailed, but there is no explicit confirmation of compliance with NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782 NDE requirements. For the specified OD, eddy current testing is not feasible, and other NDE methods are only a...

Open

15835

5.2

AI

No

add date

There is no explicit confirmation that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor confirmation that the required NDE will be performed as standard for the specified pip...

Open

15836

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: ASTM A790, NORSOK MDS D51 Rev 6

Open

15837

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and ASTM A999 as required, with no overriding TechnipFMC specification indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 312-01a ...

Open

15838

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15839

8.0

AI

No

add date

Marking is performed according to ASTM A790, including heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13...

Open

15840

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15841

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

15842

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

15843

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling supplier qualification documentation requirem...

Open

15844

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to the products as required by SIR205 and section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/0...

Open

15845

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 ...

Open

15846

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of metallurgical and non-d...

Open

15847

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the item table and confirmed by the digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, DMV_STANDARD_...

Open

15848

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR availability for review as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15849

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

15850

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15851

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: Digest NORSOK MDS D51 Rev 06.docx

Open

15852

3.1

AI

No

add date

Chemical composition for UNS S32760 conforms to Table 2 of ASTM A790, matching the specified limits, with heat analysis and supplier certification provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-0...

Open

15853

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

15854

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

15855

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

15856

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is fulfilled. The ordered pipe dimensions al...

Open

15857

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

15858

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets the minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) requirements per NORSOK MDS D51 Rev 6 and ASTM A790 for the specified grade and product form. Source: ...

Open

15859

4.3

AI

No

add date

Pipe wall thickness exceeds minimum required for Charpy V-notch testing per ASTM A370 or ISO 148-1; requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests i...

Open

15860

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal; the specified pipe dimensions allow for required transverse testi...

Open

15861

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified electrolytic etchant after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

15862

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination and fulfills the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

15863

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

15864

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs are included and recorded as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

15865

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

15866

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states that weld repairs are not acceptable for MST-Tubes, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15867

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

15868

4.4.2

AI

No

add date

No provided documentation prohibits all intermetallic phases and/or precipitates when CVN testing cannot be completed; some isolated precipitates are allowed, which does not meet the stricter client requirement. Source: DMV_STANDARD_BOOK/02-03-01 - D...

Open

15869

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

15870

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

15871

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

15872

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed or confirmed. Relevant standards and tests are not explicitly mentioned or confirmed in the available documentation. Source: DMV_STANDARD...

Open

15873

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 (ASTM A790, NORSOK M-630, M-650/ISO 17782) are fully met, including compliance for destructive and microstructural tests (tensile, impact, corrosion, ferrite, microstructure). ...

Open

15874

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A @ 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and is confirmed compliant. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

15875

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

15876

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 and ISO 10893-10 is supported for the specified pipe dimensions; calibration notch details are assumed to follow ASTM E213 as required. Source: DMV_STANDARD_BOOK/12 - Speci...

Open

15877

5.2

AI

No

add date

NDE per ASTM A790 is available, but compliance with additional NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 NDE requirements is not confirmed. Standard NDE (eddy current, ultrasonic, hydrostatic) is not fully feasible for the requested OD at Montb...

Open

15878

5.2

AI

No

add date

No provided documentation explicitly confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor that the required NDE with this acceptance criterion will be performed as ...

Open

15879

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are per ASTM A790/A999 as required, with no deviations specified in the client documentation. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according ...

Open

15880

8.0

AI

No

add date

Marking is performed per ASTM A790 (§14) and includes heat number and lot number using indelible black ink or vibro-etching, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06....

Open

15881

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15882

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

15883

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

15884

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

15885

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

15886

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

15887

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

15888

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and full metallurgical and non-destructive test results—ar...

Open

15889

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

15890

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

15891

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

15892

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard and required for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS...

Open

15893

3.1

AI

No

add date

UNS S32760 chemical composition matches Table 2 requirements and is confirmed by supplier certification and heat analysis per ASTM A790 for DMV material. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-0...

Open

15894

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

15895

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

15896

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and direct reference to Table 3, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

15897

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure tests are performed at specified locations an...

Open

15898

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with tensile and hardness properties meeting Table 4 requirements for NORSOK MDS D51/ASTM A790. Hardness testing is also performed per ASTM A790, and DMV 25.7N complies. So...

Open

15899

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

15900

4.3

AI

No

add date

Pipe wall thickness (18.26 mm) exceeds minimum required for Charpy V-notch testing per ASTM A370 and ISO 148-1; testing is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Im...

Open

15901

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C with minimum average/single values of 45/35 J (transverse) and 65/50 J (longitudinal) for thickness >6mm. The specified pipe dimensions allow f...

Open

15902

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, using the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

15903

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

15904

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

15905

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

15906

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, reported at actual magnification and including a scale bar, if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - ...

Open

15907

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

15908

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Zero-tolerance is not guaranteed by the provided information. Source: D...

Open

15909

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

15910

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

15911

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: microstructure examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides r...

Open

15912

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

15913

4.5

AI

No

add date

Corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is not explicitly confirmed or documented in the available information. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

15914

4.5

AI

No

add date

Acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6 are met, including chemical composition (PRE ≥ 40), microstructure (free from intermetallics, ferrite 35-60%), impact, corrosion, and tensile properties. Required tests and pro...

Open

15915

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781 (G48 Method A @ 50°C, 24h). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Diges...

Open

15916

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in...

Open

15917

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, with testing performed after all mechanical processing, heat treatments, and straightening. Reference notch...

Open

15918

5.2

AI

No

add date

NDE methods required by ASTM A790 and NORSOK M-630 MDS D51/650 are not fully addressed for the specified pipe dimension and grade. Eddy current testing is not feasible for OD 219.1 mm, hydrostatic and ultrasonic tests are only available at extra cost...

Open

15919

5.2

AI

No

add date

No provided source explicitly states that any indication greater than the calibration notch is considered a defect requiring rejection or repair of pipe/tubing, nor confirms standard NDE application for the specified OD. Source: DMV_STANDARD_BOOK/02-...

Open

15920

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are per ASTM A790 and ASTM A999, as required, with no overriding specifications indicated by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances...

Open

15921

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods (indelible ink, vibro-etching) include heat and lot numbers, ensuring traceability as required. Source: DMV_STA...

Open

15922

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

15923

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

15924

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

15925

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15926

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

15927

10.2

AI

No

add date

ISO 9001 certification is provided and documentation traceable to delivered products is included, meeting SIR205 and specification section 10.0 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-...

Open

15928

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 manufacturing summary/QTR number). Source: DMV_STANDARD_B...

Open

15929

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis (ladle analysis), solution annealing...

Open

15930

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the item table and confirmed by the digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04...

Open

15931

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15932

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process follows M-650 (or ISO 17782) qualified procedures, fulfilling the requirement for manufacturer and process qualification per NORSOK M-65...

Open

15933

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production; chemical analysis for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15934

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSO...

Open

15935

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is covered by compliance...

Open

15936

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

15937

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and procedure for destructive testing, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

15938

4.1

AI

No

add date

DMV 25.7N seamless pipes are tested for tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse, or longitudinal if transverse not possible), and corrosion/microstructure at specified thickness locations, in accordance with NORS...

Open

15939

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with mechanical properties (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and maximum hardness in accordance with Table 4, as required. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

15940

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

15941

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

15942

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and standards; requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/1...

Open

15943

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if transverse...

Open

15944

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, using the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

15945

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH solution or other suitable etchant(s) to show ferrite balance and intermetallic phases is required, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spe...

Open

15946

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

15947

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

15948

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

15949

4.4.2

AI

No

add date

Micrographic examination requires reporting of centerline intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

15950

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not fulfil...

Open

15951

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

15952

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

15953

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

15954

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

15955

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

15956

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

15957

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available for the specified pipe dimensions, performed after all mechanical processing, with calibration notches as required. Source: DMV_STANDARD_BOOK/12 - Special Tes...

Open

15958

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT) is confirmed, but compliance with specific NDE requirements of NORSOK M-630 MDS D51 or NORSOK M-650/ISO 17782 is not demonstrated. For OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/...

Open

15959

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, nor is this acceptance criterion demonstrated for the specified pipe dimensions or NDE methods. Sour...

Open

15960

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no overriding specifications indicated; requirement is fulfilled. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 -...

Open

15961

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15962

8.0

AI

No

add date

Marking per ASTM A790 includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Marking methods (indelible ink, vibro-etching) are standard and applied as specified. Source: DMV_STANDARD_BOOK/02-04-03 - Diges...

Open

15963

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 explicitly states 'Weld repairs not acceptable,' fulfilling the requirement for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15964

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

15965

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the required quality-assurance system specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORS...

Open

15966

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, demonstrating qualification for the specified size and product ...

Open

15967

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

15968

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

15969

10.2

AI

No

add date

Documentation and certification details required by NORSOK M-650/ISO 17782, including identification/QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical an...

Open

15970

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

15971

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis complies with Table 2 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

15972

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Chemical composition matches the requirement table and is confirmed by supplier certification and heat analys...

Open

15973

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is covered by compliance...

Open

15974

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

15975

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

15976

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790/NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locat...

Open

15977

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

15978

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 06 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW, with testing per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

15979

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements at -46°C, with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal, including reduction factors for sub-...

Open

15980

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, including etching to detect intermetallic phases and ferrite balance using the specified solution after final polishing. Source: DMV_STANDARD_BOOK/02...

Open

15981

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases is required in accordance with ISO 17781, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15982

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

15983

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

15984

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

15985

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

15986

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

15987

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fulfilled. Source: DMV_STANDAR...

Open

15988

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

15989

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

15990

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

15991

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided; neither ASTM G48 nor ISO 17781 are mentioned, and the required test parameters are not specified. Source: DMV_STANDARD_BOOK/12-03-01- Corro...

Open

15992

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, as well as manufacturing, heat treatment, and qualification standards. Source: DMV_STANDAR...

Open

15993

4.5

AI

No

add date

DMV 25.7N undergoes pitting corrosion testing per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

15994

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor are their roles and responsibilities defined as required by the specification. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive...

Open

15995

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

15996

5.2

AI

No

add date

100% of pipes are subject to hydrostatic or nondestructive electric (EC/UT) testing as per ASTM A999, fulfilling the NDE requirement of ASTM A790 for seamless pipe as specified in the inquiry context. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

15997

5.2

AI

No

add date

The available documents do not specify that any indication greater than that produced by the calibration notch is considered a defect, nor do they confirm rejection or repair of such pipes and tubing. NDE acceptance criteria and calibration notch ref...

Open

15998

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790/A999) for the specified product dimensions, with no deviations indicated in the client specification or drawing. Source: DMV_STANDARD_BOOK/07-01 - General informat...

Open

15999

8.0

AI

No

add date

Marking is performed per ASTM A790 (§14) and includes heat number and lot number using indelible ink or vibro-etching, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, ...

Open

16000

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N with relevant wall thickness, but not to ISO 17782 as required; no evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16001

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

16002

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, and material-specific assessment is covered by NORSOK M-650/ISO 17782 qualification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

16003

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

16004

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

16005

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

16006

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

16007

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer name, actual heat number, specific chemical analysis, solution annealing parameters, and actual metallurgical and non-de...

Open

16008

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Diges...

Open

16009

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of full qualification to both standards or availability of QTR/MPCR documentation for review as required. Source: DMV_STANDARD_B...

Open

16010

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

16011

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production; chemical analysis for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16012

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits and PREN ≥ 40 as specified in Table 2, per ASTM A790 and NORSOK MDS D51 Rev 06. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16013

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is covered by compliance...

Open

16014

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot, with lot defined according to ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04...

Open

16015

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

16016

4.1

AI

No

add date

DMV 25.7N seamless pipes are tested for tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure per NORSOK MDS D51/ASTM A790, with required thickness locations. For the ordered ...

Open

16017

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

16018

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: yield ≥ 550 MPa, tensile ≥ 750 MPa, elongation ≥ 25%, hardness ≤ 310 HBW, matching client specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

16019

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and standards; requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/1...

Open

16020

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -466C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal (if transverse not possible), for thickness 6 mm. The specified ...

Open

16021

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed according to ISO 17781, with specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

16022

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

16023

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

16024

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

16025

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

16026

4.4.2

AI

No

add date

Presence of centerline intermetallic stringers must be reported, and acceptance is based on CVN and corrosion test results as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

16027

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fulfilled. Source: DMV_S...

Open

16028

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

16029

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

16030

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

16031

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

16032

4.5

AI

No

add date

No explicit confirmation that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) is performed in accordance with ISO 17781 is provided in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

16033

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including destructive and micrographic tests, ferrite content, and corrosion/impact requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

16034

4.5

AI

No

add date

DMV 25.7N undergoes pitting corrosion testing per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², both of which are met. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

16035

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in...

Open

16036

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

16037

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled; only ASTM A790/A999 NDE is detailed. For OD 219.1 mm, eddy current testing is not feasible at Montbard, hydrostatic and ultrasonic tests...

Open

16038

5.2

AI

No

add date

Referenced standards and plant feasibility documents do not explicitly confirm that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor that such NDE is feasible for the specified pipe size at Mont...

Open

16039

6.0

AI

No

add date

Dimensional tolerances are per applicable ASTM standard (ASTM A790/A999) for the specified pipe size, with no overriding tolerances stated in the customer specification or drawing. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDA...

Open

16040

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16041

8.0

AI

No

add date

Marking per ASTM A790 and standard methods (indelible ink, vibro-etching) include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Certification per EN 10204 3.1 provides supporting traceability information. ...

Open

16042

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body established within the EEA and specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

16043

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, meeting the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-0...

Open

16044

10.1

AI

No

add date

Supplier MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the requirement for qualification for ...

Open

16045

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is issued and includes all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufacturing summary identific...

Open

16046

10.2

AI

No

add date

NORSOK M-650/ISO 17782 identification, QTR/MPCR number, steel producer, heat number, solution annealing parameters, and actual metallurgical and NDT test results are not fully provided; only general certificate and process information is available, a...

Open

16047

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by specification references and digest documentation. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16048

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not to ISO 17782, as required. No evidence of QTR/MPCR documentation availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16049

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

16050

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16051

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits specified in Table 2, including PREN ≥ 40, as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16052

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is implici...

Open

16053

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790, with test frequency specified as '1/lot'. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

16054

4.1

AI

No

add date

Tensile test sampling is performed according to Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, fulfilling the requirement for test specimen sampling as outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

16055

4.1

AI

No

add date

DMV 25.7N seamless pipes are tested per NORSOK MDS D51/ASTM A790 requirements: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure at specified thickness locations. For the o...

Open

16056

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370, with required properties (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and maximum hardness per Table 4; DMV 25.7N complies. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

16057

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) per NORSOK MDS D51 Rev 6 and ASTM A790 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

16058

4.3

AI

No

add date

Pipe wall thickness (18.26 mm) exceeds minimum required for Charpy V-notch testing per ASTM and ISO standards; testing as specified is feasible and requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/1...

Open

16059

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16060

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C with minimum average/single values of 45/35 J (transverse) and 65/50 J (longitudinal) for thickness >6mm. The specified pipe dimensions allow f...

Open

16061

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, using the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

16062

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

16063

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

16064

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

16065

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

16066

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 requires reporting of intermetallic phases, with acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria...

Open

16067

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is...

Open

16068

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

16069

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

16070

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50°C, 24h) in accordance with ISO 17781 is provided in the referenced documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

16071

4.5

AI

No

add date

DMV 25.7N (UNS S32760) fulfills all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and N...

Open

16072

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A @ 50°C, 24h) requires no pitting at 20X magnification and weight loss < 1.0 g/m²; DMV 25.7N complies with both requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

16073

5.1

AI

No

add date

No evidence provided regarding qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montb...

Open

16074

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

16075

5.2

AI

No

add date

NDE per ASTM A790 is partially addressed with hydrostatic or EC/UT testing per ASTM A999, but there is no explicit evidence of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements. For OD 219.1 mm, eddy curre...

Open

16076

5.2

AI

No

add date

None of the relevant documents explicitly state that any indication greater than the calibration notch is considered a defect requiring rejection or repair of pipe/tubing, nor do they confirm standard NDE practices for the specified OD. Requirement n...

Open

16077

6.0

AI

No

add date

Dimensional tolerances for the pipe are per the applicable ASTM standard (ASTM A790 references ASTM A999 for tolerances), with no evidence of other stated tolerances in the specification or customer documents. Source: DMV_STANDARD_BOOK/07-01 - Genera...

Open

16078

7.0

AI

No

add date

Finished pipes are required to be white pickled or bright annealed by both ASTM A790 (section 6.1.3) and NORSOK MDS D51 Rev 06 (§13), fulfilling the requirement. Source: ASTM A790, NORSOK MDS D51 Rev 06.

Open

16079

8.0

AI

No

add date

Marking is performed according to ASTM A790 (§14), ensuring full traceability to melt and heat treatment lot. Marking methods (indelible black ink, vibro-etching) include heat number and DMV lot number, fulfilling the requirement. Source: DMV_STANDAR...

Open

16080

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' confirming the requirement is met for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03...

Open

16081

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/...

Open

16082

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

16083

10.1

AI

No

add date

Supplier is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the requirement for qualification for the spe...

Open

16084

10.2

AI

No

add date

No explicit confirmation that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205; available sources only mention general certification and documentation types without confirming compliance with the transmi...

Open

16085

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, including heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 manufacturing summary/QTR number. Source: DMV_ST...

Open

16086

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or actual metallurgical and non-destru...

Open

16087

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by specification references and digest documentation. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16088

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability or full qualification to both standards as required by the specification. Source: DMV_STANDARD_BOOK/02-...

Open

16089

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process follows M-650 (or ISO 17782) qualified procedures, fulfilling the requirement for manufacturer and process qualification and meeting N...

Open

16090

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16091

3.1

AI

No

add date

Chemical composition for S32760 matches the specified limits in Table 2 for ASTM A790, with both heat and product analysis required to conform to these values. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/0...

Open

16092

3.2

AI

No

add date

Pipes are solution annealed followed by water quenching per ASTM A790, furnaces are qualified to NORSOK M-650/ISO 17782, and pipe arrangement ensures free circulation of heating and cooling media during heat treatment. Source: DMV_STANDARD_BOOK/02 - ...

Open

16093

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

16094

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for sampling requirements, fulfilling the specification for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

16095

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, all per NORSOK/ASTM st...

Open

16096

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

16097

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required by NORSOK MDS D51 Rev 6 and ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

16098

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions (WT 18.26mm, OD 219.1mm), fulfilling the requirement. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

16099

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements: Charpy V-notch testing at -46°C, minimum transverse absorbed energy (average/single) 45 J/35 J, longitudinal (if transverse not possible) 65 J/50 J, with sub-size reduction factors. T...

Open

16100

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, using the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

16101

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B is explicitly required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDA...

Open

16102

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

16103

6.0

AI

No

add date

Dimensional tolerances for the specified pipe are per ASTM A790 and ASTM A999, as required, with no overriding tolerances specified by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances acco...

Open

16104

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781, with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STAND...

Open

16105

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

16106

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

16107

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits all intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully fulfilled. Source: DMV_S...

Open

16108

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Sou...

Open

16109

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

16110

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

16111

4.5

AI

No

add date

Corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is not explicitly referenced in the provided standards or specifications, so fulfillment cannot be confirmed. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Mo...

Open

16112

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, chemical composition, ferrite content, corrosion resistance, impact, and microstructure, and is M-650 qualifi...

Open

16113

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 24h, 50°C) is performed with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m²; DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

16114

5.1

AI

No

add date

No evidence is provided confirming NDE personnel are qualified and certified to ISO 9712 level II or III, nor are their roles and responsibilities defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Mo...

Open

16115

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including calibration notches as specified, and pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non d...

Open

16116

5.2

AI

No

add date

NDE per ASTM A790 is partially addressed with 100% hydrostatic or EC/UT testing per ASTM A999, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE acceptance criteria are met. Standard NDE methods for the s...

Open

16117

5.2

AI

No

add date

No provided documentation explicitly confirms that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor is there confirmation that the required NDE is feasible for the specified pipe dimensions at M...

Open

16118

8.0

AI

No

add date

Marking per ASTM A790 includes heat and lot number for full traceability; Montbard plant marking methods (indelible ink, vibro-etching) ensure traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev...

Open

16119

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly prohibits weld repairs under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-0...

Open

16120

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

16121

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-...

Open

16122

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification dem...

Open

16123

10.2

AI

No

add date

No provided documentation confirms transmission of SIR205 or other traceable documents to TechnipFMC as required. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDAR...

Open

16124

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and will be issued, including all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and M-650/ISO17782 manufactur...

Open

16125

10.2

AI

No

add date

Most required documentation and certification details (NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel melting practice, refining method, heat number, chemical analysis, solution annealing details, metallurgical and NDT results) are s...

Open

16126

1.0

AI

No

add date

DMV 25.7N is a 25 Cr Duplex stainless steel seamless pipe manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, as referenced in the order and confirmed by specification digests. Source: DMV...

Open

16127

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760/DMV25.7N (up to certain wall thicknesses) but not to ISO 17782; no evidence of QTR/MPCR availability. Full compliance with NORSOK M-650/ISO 17782 is not demonstrated. Source: DMV_STANDARD_BOOK/02-...

Open

16128

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

16129

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 of ASTM A790 and NORSOK MDS D51 requirements. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16130

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, and matches ASTM A790 and NORSOK MDS D51 Rev 06 specifications. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/...

Open

16131

3.2

AI

No

add date

Solution annealing followed by accelerated cooling is performed per ASTM A790; manufacturing and furnace qualification comply with NORSOK M-650/ISO 17782; free circulation of heating/cooling media is ensured by adherence to these standards. Source: D...

Open

16132

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790, with test frequency '1/lot'. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

16133

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, directly referencing the table for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detai...

Open

16134

4.1

AI

No

add date

Test sampling requirements for seamless pipes per NORSOK MDS D51/ASTM A790, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests, with specified locations and d...

Open

16135

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

16136

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

16137

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact ...

Open

16138

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse absorbed energy (average 45 J, single 35 J), and minimum longitudinal absorbed energy (average 65 J, single 50 J if transv...

Open

16139

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, including etching for intermetallic phases and ferrite balance using the specified solution after final polishing. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

16140

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

16141

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and each is below 10 μm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

16142

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and photos are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STANDARD_BO...

Open

16143

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

16144

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

16145

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully fulfilled. Source: DMV_STA...

Open

16146

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

16147

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

16148

4.4.3

AI

No

add date

Micrographic examination is specified as per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and ...

Open

16149

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16150

4.5

AI

No

add date

No explicit confirmation or evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 will be performed or is fulfilled in the referenced documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Mon...

Open

16151

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

16152

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A @ 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

16153

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montb...

Open

16154

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

16155

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed; only ASTM A790/A999 NDE is detailed. Eddy current testing is not feasible for OD 219.1 mm at Montbard, and hydrostatic/ultrasonic tests are only available ...

Open

16156

5.2

AI

No

add date

None of the referenced documents explicitly state that any indication greater than that produced by the calibration notch is considered a defect, nor do they confirm that defective pipe and tubing will be rejected or repaired according to this criter...

Open

16157

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), including OD, WT, and ovality, with no deviations or special customer requirements indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_S...

Open

16158

7.0

AI

No

add date

ASTM A790 (6.1.3) and NORSOK MDS D51 (§13) both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16159

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790, ensuring full traceability to melt and heat treatment lot. Marking methods include heat number and lot number as standard content, fulfilling the requirement for traceability. Source: DMV_STANDARD...

Open

16160

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 explicitly states 'Weld repairs not acceptable,' directly fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

16161

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/...

Open

16162

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

16163

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

16164

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

16165

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

16166

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. No evidence of ...

Open

16167

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and are M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

16168

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability or full qualification to both standards as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

16169

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

16170

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16171

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16172

3.2

AI

No

add date

Solution annealing followed by accelerated cooling is performed per ASTM A790; manufacturing and furnaces are qualified per NORSOK M-650/ISO 17782; free circulation of heating/cooling media is ensured by compliance with these standards. Source: DMV_S...

Open

16173

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

16174

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for sampling requirements, fulfilling the specification for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

16175

4.1

AI

No

add date

Test sampling for seamless pipes per ASTM A790/NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, longitudinal if not possible), and corrosion/microstructure tests are performed at specified locations. Pipe ...

Open

16176

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

16177

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

16178

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, meeting the requirement for impact testing as per Table 5. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-...

Open

16179

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse absorbed energy (average/single) of 45 J/35 J, and longitudinal (if transverse not possible) of 65 J/50 J. The specified p...

Open

16180

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, using the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

16181

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

16182

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

16183

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

16184

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, reported at actual magnification and including a scale bar, if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - ...

Open

16185

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

16186

4.4.2

AI

No

add date

No document specifies a zero-tolerance for intermetallic phases and/or precipitates if CVN testing cannot be completed; isolated precipitates are permitted under current specifications, which does not meet the requirement. Source: DMV_STANDARD_BOOK/0...

Open

16187

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

16188

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosio...

Open

16189

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16190

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spe...

Open

16191

4.5

AI

No

add date

DMV 25.7N meets the requirement of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 ...

Open

16192

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in...

Open

16193

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

16194

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially addressed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are fulfilled. For the requested OD (219.1 mm), eddy current testing ...

Open

16195

5.2

AI

No

add date

No provided documentation confirms the acceptance criterion that any indication greater than the calibration notch is a defect requiring rejection or repair, nor is NDE capability for the specified OD confirmed. Source: DMV_STANDARD_BOOK/02-03-01 - D...

Open

16196

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790 referencing ASTM A999) unless otherwise specified, with no evidence of override by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-0...

Open

16197

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, ensuring full traceability to melt and heat treatment lot. Marking methods (indelible ink, vibro-etching) include heat and lot numbers as required. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ...

Open

16198

9.0

AI

No

add date

Weld repairs are explicitly stated as not acceptable in the specification under 'Surface finish / Repairs of defects' (§13, §14). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

16199

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-...

Open

16200

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

16201

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

16202

10.2

AI

No

add date

No provided documentation confirms transmission to TechnipFMC and traceability to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, D...

Open

16203

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, M-650/ISO17782 manufacturing summary/QTR number). Source: DMV_STANDARD_BOOK/...

Open

16204

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. No evidence is ...

Open

16205

1.0

AI

No

add date

DMV 25.7N seamless pipe is confirmed as compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-...

Open

16206

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782, and there is no evidence of QTR/MPCR documentation availability. Requirement for qualification to both NORSOK M-650/ISO 17782 and documentation access is not fulfilled. Source:...

Open

16207

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

16208

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16209

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed by heat analysis with supplier certification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Dige...

Open

16210

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is implici...

Open

16211

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

16212

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and direct reference to Table 3, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

16213

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locatio...

Open

16214

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

16215

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength 750 MPa, yield strength 550 MPa, elongation 25%, and maximum hardness 310 HBW as required by NORSOK MDS D51 Rev 6 and ASTM A790 for seamless pipe specification. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

16216

4.3

AI

No

add date

Charpy V-notch testing is feasible for the requested pipe dimensions, which exceed the minimum wall thickness required by ASTM and ISO standards. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

16217

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal (if transverse...

Open

16218

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed according to ISO 17781, with specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

16219

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution for micrographic examination to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

16220

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

16221

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

16222

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

16223

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

16224

4.4.2

AI

No

add date

Microstructure is required to be 'basically free from intermetallic precipitates,' with isolated precipitates below 10μm allowed, which does not fully meet the requirement that intermetallic phases and/or precipitates are not permitted if CVN testing...

Open

16225

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Sou...

Open

16226

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, including etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and co...

Open

16227

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16228

4.5

AI

No

add date

No evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is fulfilled; neither standard nor test is mentioned or specified in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests i...

Open

16229

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, with manufacturing and qualification processes compliant with NORSOK M-650/ISO 17782. Sour...

Open

16230

4.5

AI

No

add date

DMV 25.7N undergoes pitting corrosion testing per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD...

Open

16231

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in...

Open

16232

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions and performed after all mechanical processing, heat treatments, and straightening. Source: DMV_STANDARD_BOOK/12 - Special T...

Open

16233

5.2

AI

No

add date

NDE per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 is not confirmed; only ASTM A790/A999 NDE is detailed. For OD 219.1 mm, eddy current testing is not feasible, hydrostatic and ultrasonic tests are only available at extra cost, and standard feas...

Open

16234

5.2

AI

No

add date

The available documentation does not confirm that NDE acceptance criteria require any indication greater than the calibration notch to be treated as a defect and rejected or repaired, nor does it confirm feasibility of such NDE for the specified pipe...

Open

16235

6.0

AI

No

add date

Dimensional tolerances are confirmed as per the applicable ASTM standard (ASTM A999 referenced by ASTM A790) for the requested pipe dimensions, with no evidence of override by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV...

Open

16236

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods (indelible ink, vibro-etching) include heat and DMV lot numbers, ensuring traceability. Certification per EN 10...

Open

16237

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 explicitly states 'Weld repairs not acceptable,' fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51...

Open

16238

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

16239

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the specified quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

16240

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

16241

10.2

AI

No

add date

ISO 9001 certification is provided and documentation traceable to delivered products is included as required by SIR205 and specification section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 -...

Open

16242

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant standards and qualifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS ...

Open

16243

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer name, steel melting practice and refining method, heat number, actual chemical analysis results, solution annealing para...

Open

16244

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and are M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BO...

Open

16245

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782, and there is no evidence of QTR/MPCR documentation availability. Full qualification to both NORSOK M-650/ISO 17782 and documentation availability is not demonstrated. Source: ...

Open

16246

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

16247

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 for DMV 25.7N grade. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16248

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as per Table 2 and NORSOK MDS D51 Rev 06. Heat analysis is performed per heat and matches ASTM A790 requirements for S32760. Source: 02-03-01 - Digest AS...

Open

16249

3.2

AI

No

add date

Solution annealing followed by accelerated cooling is performed per ASTM A790; manufacturing and furnace qualification comply with NORSOK M-650/ISO 17782; MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensur...

Open

16250

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

16251

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with frequency and method matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digest...

Open

16252

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790/NORSOK MDS D51 is fulfilled: tensile tests (longitudinal or transverse), hardness, CVN (transverse, longitudinal if not feasible), and corrosion/microstructure tests are performed as specifie...

Open

16253

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

16254

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW/32 HRC) as required by NORSOK MDS D51 Rev 06 and ASTM A790. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NOR...

Open

16255

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the requested pipe dimensions, which exceed the minimum wall thickness required for transverse specimens. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructiv...

Open

16256

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C with minimum transverse values of 45 J (average) and 35 J (single), and longitudinal values of 65 J (average) and 50 J (single) if transverse ...

Open

16257

4.4.1

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching for intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and examination in accordance ...

Open

16258

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

16259

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

16260

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 is performed at ≥400x magnification, with etching to detect intermetallic phases; presence and location are noted and recorded with micrographs. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

16261

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

16262

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

16263

4.4.2

AI

No

add date

The available specifications do not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed; isolated precipitates below 10µm are permitted, which does not meet the zero-tolerance requirement. Source: DMV_STANDARD_B...

Open

16264

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Sou...

Open

16265

4.4.3

AI

No

add date

Micrographic examination is performed as per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corr...

Open

16266

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

16267

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

16268

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N, with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², both of which are met. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

16269

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement is not fulfilled based on the available information. Sou...

Open

16270

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available and applicable for the requested pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ultrasonic testing...

Open

16271

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not demonstrated. Provided documents only address NDE per ASTM A790/A999, destructive testing, or are not applicable to duplex grades. For the requested OD (219.1 m...

Open

16272

5.2

AI

No

add date

None of the reviewed documents explicitly state that any indication greater than that produced by the calibration notch represents a defect requiring rejection or repair of pipe and tubing, nor do they confirm that NDE with this acceptance criterion ...

Open

16273

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are confirmed to be per the applicable ASTM standard (ASTM A999), with no deviations specified in the customer requirements. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDA...

Open

16274

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16275

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot, and standard marking methods (indelible ink, vibro-etching) include heat number and DMV lot number as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D5...

Open

16276

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement for DMV 25.7N seamless pipe per ASTM A790 and NORSOK M-630 MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

16277

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

16278

10.1

AI

No

add date

Manufacturer is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Diges...

Open

16279

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, fulfilling supplier qualification documentation per SIR...

Open

16280

10.2

AI

No

add date

Certification to EN 10204 type 3.1 is provided, including heat treatment, steel manufacturer, melting/refining practice, NORSOK M-650/ISO17782 manufacturing summary or QTR number, and traceability to delivered products. Source: DMV_STANDARD_BOOK/02 -...

Open

16281

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

16282

10.2

AI

No

add date

Required documentation and certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and results of all required metallurgical...

Open

16283

1.0

AI

No

add date

DMV 25.7N seamless pipe is specified, fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all mechanical, chemical, and testing requirements. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_...

Open

16284

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782; no evidence of QTR/MPCR availability or full compliance with both standards as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06....

Open

16285

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

16286

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat, confirming conformity to ASTM A790 and...

Open

16287

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

16288

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

16289

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and lot requirements, directly referencing the table for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed...

Open

16290

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51 and ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, longitudinal if not possible), corrosion, and microstructure tests are performed at specified thickness l...

Open

16291

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A @ 25°C, 24h) with criteria: no pitting at 20X magnification and weight loss < 1.0 g/m², matches the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

16292

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Hardness testing is also performed per ASTM A790, with results provided. Source: DMV...

Open

16293

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

16294

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 and ISO 148-1 is feasible for the specified pipe dimensions, as the wall thickness exceeds the minimum required for both standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-...

Open

16295

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if transverse ...

Open

16296

4.4.1

AI

No

add date

ISO 17781 is referenced for micrographic examination, and general etchant types are listed, but the specific etchant solution required for intermetallic phase detection and ferrite balance electrolytic etching after final polishing is not confirmed. ...

Open

16297

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

16298

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

16299

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

16300

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

16301

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK/0...

Open

16302

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fulfilled. Source: DMV_STAN...

Open

16303

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

16304

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: microstructure examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides r...

Open

16305

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies within this range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NOR...

Open

16306

4.5

AI

No

add date

Corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is not explicitly referenced or confirmed in the provided documentation or listed standards. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

16307

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive, micrographic, ferrite, corrosion, and impact tests; manufacturing and qualification processes are accredited as required. Source: DMV_STANDARD_BOOK...

Open

16308

4.5

AI

No

add date

DMV 25.7N undergoes pitting corrosion testing per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD...

Open

16309

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

16310

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

16311

5.2

AI

No

add date

NDE per ASTM A790 is partially supported, but there is no explicit evidence of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782. For the specified OD, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only...

Open

16312

5.2

AI

No

add date

None of the relevant documents explicitly confirm that indications greater than the calibration notch are classified as defects requiring rejection or repair for the specified product and dimension. NDE acceptance criteria and calibration notch compa...

Open

16313

6.0

AI

No

add date

Dimensional tolerances for the specified pipe are per the applicable ASTM standard (ASTM A790 referencing ASTM A999), with no overriding tolerances stated in the client specification or drawing. Source: DMV_STANDARD_BOOK/07.01 - General information.d...

Open

16314

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16315

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 (§14), both requiring full traceability to melt and heat treatment lot. Marking methods (indelible ink, vibro-etching) include heat number and DMV lot number, ensuring traceability as spec...

Open

16316

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

16317

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body established within the EEA and specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

16318

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers as specified in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

16319

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, fulfilling the requirement. Source: DMV_STANDARD_BOOK/0...

Open

16320

10.2

AI

No

add date

Certification includes EN 10204 type 3.1 with traceability to product, and MST-Tubes is ISO 9001 certified, fulfilling the requirement for documentation traceable to delivered products (SIR205). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

16321

8.0

AI

No

add date

Marking methods include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/13-02-01 - Standard marking feasibility - Montbard plant.doc

Open

16322

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630 for the product in question. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certification ...

Open

16323

10.2

AI

No

add date

Most documentation and certification requirements (NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, metallurgical and non-destructive test results) are either not pro...

Open

16324

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 rev. 6, meeting all relevant mechanical, chemical, and testing specifications for 25 Cr Duplex stainless steel seam...

Open

16325

1.0

AI

No

add date

No provided document confirms supplier qualification to both NORSOK M-650 and ISO 17782 for the exact product supplied, nor the availability of the full Qualification Test Record/MPCR for review by TechnipFMC as required by the specification. Source:...

Open

16326

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N within specified wall thickness limits, and the manufacturing process is qualified per NORSOK M-650 (or ISO 17782), meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD...

Open

16327

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis complies with Table 2 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

16328

3.1

AI

No

add date

Manufacturing process is qualified according to NORSOK M-650 for UNS S32760 / DMV25.7N up to WT = 31.75 mm, covering the inquiry WT of 18.26 mm. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Diges...

Open

16329

3.2

AI

No

add date

Heat treatment (solution annealing followed by accelerated cooling) is performed per ASTM A790, with manufacturing process and furnaces qualified according to NORSOK M-650/ISO 17782. Free circulation of heating/cooling media is ensured by compliance ...

Open

16330

4.1

AI

No

add date

No evidence that impact, tensile, hardness, corrosion testing, and microstructure examinations are performed for each heat and heat treatment lot as defined in ASTM A790; testing frequency and lot definition are not confirmed for all required tests. ...

Open

16331

4.1

AI

No

add date

Test specimen sampling is outlined in Table 3 as required for tensile tests. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.docx

Open

16332

4.1

AI

No

add date

Test sampling requirements for tensile, CVN, corrosion, and microstructure (including test directions and thickness locations per ASTM A790 and Table 3) are not fully addressed; information on CVN impact testing and detailed sampling locations is mis...

Open

16333

4.2

AI

No

add date

Tensile testing is performed in accordance with ASTM A370 as required, and material meets specified tensile and hardness properties. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-...

Open

16334

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis complies with Table 2 for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16335

4.2

AI

No

add date

Mechanical property values (tensile strength, yield strength, elongation, hardness) required are not explicitly confirmed or do not meet the specified requirements for DMV 25.7N (Tensile ≥ 750 MPa, Yield ≥ 550 MPa, Elongation ≥ 25%, Hardness max 310 ...

Open

16336

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, meeting the minimum wall thickness requirements for both standards. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished produc...

Open

16337

4.3

AI

No

add date

Pipe dimensions allow for transverse Charpy V-notch specimens; impact property requirements for transverse and longitudinal directions can be met as specified at -46°C. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

16338

4.4.1

AI

No

add date

No information is provided regarding metallographic preparation, examination procedures, or compliance with ISO 17781 for 25 Cr Duplex stainless steels, nor about the specified etching procedures for intermetallic phases and ferrite balance. Source: ...

Open

16339

4.4.1

AI

No

add date

No evidence of use of 20-40% NaOH or KOH solution or other suitable etchant(s) as per ISO 17781 Appendix B for micrographic examination; requirement not fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - ...

Open

16340

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic phases; isolated phases are permitted if not homogeneously distributed and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

16341

4.4.2

AI

No

add date

No evidence of detection, location, or micrographic documentation (400x minimum) of intermetallic phases is provided; only grain size measurement is addressed. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-03 - Micr...

Open

16342

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

16343

4.4.2

AI

No

add date

No provided documents address the reporting of centerline intermetallic stringers or acceptance based on CVN and corrosion test results in such cases. Source: DMV_STANDARD_BOOK/12-03-03 - Grain Size Examination in DMV-I.doc, DMV_STANDARD_BOOK/12-03-0...

Open

16344

4.4.2

AI

No

add date

Referenced specifications allow isolated intermetallic precipitates below 10μm and do not enforce a zero-tolerance policy for intermetallic phases/precipitates if CVN testing cannot be completed, as required by the client specification. The requireme...

Open

16345

4.4.3

AI

No

add date

No evidence of ferrite content measurement per ASTM E 562 or ASTM E 1245 in accordance with ISO 17781; only grain size measurement is discussed, not ferrite content determination or required methods. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-...

Open

16346

4.4.3

AI

No

add date

No acceptance criteria for micrographic examination are specified or fulfilled in the provided documents for DMV 25.7N or the specific inquiry. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

16347

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is explicitly specified and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D41 Rev 06.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16348

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided; only A790 NORSOK is referenced, which does not confirm compliance with this requirement. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion test...

Open

16349

4.5

AI

No

add date

No acceptance criteria for metallurgical properties are specified or detailed in the provided documents or section headings, so the requirement is not fulfilled. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 ...

Open

16350

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR documentation availability. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16351

5.1

AI

No

add date

No provided documents contain information on the qualification or certification of NDE personnel to ISO 9712 level II or III, nor on their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing...

Open

16352

5.2

AI

No

add date

No explicit confirmation of 100% ultrasonic testing per ASTM E213 or ISO 10893-10 after all processing, nor of calibration notch specifications as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - Ult...

Open

16353

5.2

AI

No

add date

Dye penetrant testing is available for tube ends and bevels as specified, and 100% qualitative anti-mixing PMI is performed on standard production at Montbard, fulfilling the NDE acceptance criteria for the requirement. Source: DMV_STANDARD_BOOK/12-0...

Open

16354

5.2

AI

No

add date

None of the relevant documents confirm that indications greater than the calibration notch are treated as defects requiring rejection or repair for the specified product and dimension; acceptance criteria and rejection/repair policy are not explicitl...

Open

16355

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed to be per the applicable ASTM standards (including ASTM A790/A999) for the specified dimensions, with no deviations or special tolerances indicated in the specification or referenced docume...

Open

16356

7.0

AI

No

add date

Finished pipes are required to be white pickled or bright annealed, which is explicitly specified in both ASTM A790 and NORSOK MDS S01 standards for surface condition and finish. Source: ASTM A790, NORSOK MDS S01.

Open

16357

9.0

AI

No

add date

NORSOK MDS S01 Rev 05 requires that weld repairs are not acceptable for MST-Tubes. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS S01 Rev 05 .docx

Open

16358

10.0

AI

No

add date

No evidence of ISO 9001 or equivalent quality-assurance system certification by a competent EEA body with specific assessment for materials is provided in the available documentation. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV_STA...

Open

16359

10.1

AI

No

add date

No evidence that the manufacturer has an ISO 9001 quality-assurance system certified by a competent EEA body as required by the specification or that the required documentation will be submitted to TechnipFMC for approval. Source: DMV_STANDARD_BOOK/1...

Open

16360

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling supplier qualification documentation for the ...

Open

16361

10.2

AI

No

add date

No explicit evidence that documentation traceable to the products and required by SIR205 will be transmitted to TechnipFMC; no mention of SIR205 or traceability in the provided documents. Source: DMV_STANDARD_BOOK/14-01 - General information.doc, DMV...

Open

16362

10.2

AI

No

add date

Material certificate will be issued according to EN 10204 Type 3.1 and will include information required by ASTM A790 and NORSOK M-630 as referenced in the specification and order requirements. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.d...

Open

16363

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, with etching using 20-40% NaOH or KOH after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

16364

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

16365

10.2

AI

No

add date

No provided document contains the required documentation or certification details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, or resul...

Open

16366

1.0

AI

No

add date

DMV 25.7N seamless pipes are manufactured in full compliance with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all relevant chemical, mechanical, manufacturing, and testing requirements. M-650 qualification is confirmed for the required wall ...

Open

16367

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to WT = 31.75 mm) but not to ISO 17782; full qualification to NORSOK M-650/ISO 17782 is not demonstrated and availability of QTR/MPCR is not confirmed. Source: DMV_STANDARD_BOOK/02-...

Open

16368

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process follows M-650 (or ISO 17782) qualified procedures, fulfilling the requirement for manufacturer and process qualification and meeting N...

Open

16369

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat, confirming conformity to the required ...

Open

16370

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

16371

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with lot defined according to ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

16372

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

16373

4.1

AI

No

add date

DMV 25.7N seamless pipes are tested for tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure at specified locations and directions. For the ordered pipe (OD 219...

Open

16374

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370, with required properties (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and maximum hardness as specified in Table 4. Hardness testing is also performed per ASTM A790. Source: DMV_STANDARD_BOO...

Open

16375

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

16376

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and standards; requirement is fulfilled. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/1...

Open

16377

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse (average/single) 45J/35J, minimum longitudinal (average/single) 65J/50J, and reduction factors for sub-size specimens. The ...

Open

16378

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

16379

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

16380

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, at or near mid-wall thickness, reported at actual magnification and including a scale bar if intermetallic phases are not detected. Source: DMV_STANDARD_B...

Open

16381

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

16382

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10 µm, but does not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed, as required by the client specification. Source: DMV_STANDARD_BOOK/02-0...

Open

16383

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Sou...

Open

16384

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781 with specified etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact an...

Open

16385

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

16386

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the applicable standards or documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.d...

Open

16387

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16388

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A) at 50°C for 24 hours, with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

16389

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

16390

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 or ISO 10893-10 is available after all processing, and the dimensional range is supported. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12...

Open

16391

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are met, but NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782-specific NDE requirements are not validated. For the requested OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/ultrasonic te...

Open

16392

5.2

AI

No

add date

The available documents do not explicitly confirm that any indication greater than the calibration notch is considered a defect requiring rejection or repair, and standard NDE is not feasible for the requested OD at Montbard. Source: DMV_STANDARD_BOO...

Open

16393

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 seamless pipe are per the applicable ASTM standard (ASTM A999), with no stated deviations or overrides in the customer specification. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07...

Open

16394

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 (§14), both requiring full traceability to melt and heat treatment lot. Marking methods (indelible ink, vibro-etching) include heat number and DMV lot number, ensuring traceability as stan...

Open

16395

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

16396

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D...

Open

16397

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

16398

10.2

AI

No

add date

Certification includes EN 10204 type 3.1 with traceability to heat treatment, steel manufacturer, melting/refining practice, and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, ensuring documentation is traceable to delivered products and ...

Open

16399

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided, including all information required by ASTM A790 and NORSOK M-630, and validated by Quality Control for mill inspection. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BO...

Open

16400

10.2

AI

No

add date

EN 10204 type 3.1 certificates will include NORSOK M-650/ISO 17782 identification, steel melting practice, and heat treatment condition, but only the country of origin of the steel supplier is provided, not the specific steel producer. No batch-speci...

Open

16401

1.0

AI

No

add date

DMV 25.7N seamless pipes are confirmed to be fully compliant with ASTM A790 and all supplementary requirements of NORSOK M-630 MDS D51 Rev 6, including mechanical, chemical, corrosion, and testing requirements. Manufacturing is M-650 qualified for th...

Open

16402

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (with wall thickness limitations), but not to ISO 17782. No evidence of QTR/MPCR documentation availability. Requirement for qualification to both NORSOK M-650 and ISO 17782 is not ful...

Open

16403

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

16404

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed to conform per heat analysis. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.do...

Open

16405

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling (water quenching) per ASTM A790; manufacturing process and furnaces are qualified per NORSOK M-650/ISO 17782; pipes are placed to ensure free circulation of heating and cooling media...

Open

16406

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16407

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, fulfilling the requirement that sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

16408

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations. The ordered pipe...

Open

16409

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

16410

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

16411

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 and ISO 148-1 is feasible for the specified pipe dimensions, meeting the requirement for both longitudinal and transverse directions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-0...

Open

16412

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum absorbed energies of 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal if transverse is not ...

Open

16413

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, with etching for intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, fulfilling the requirement. Source: DMV_STA...

Open

16414

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is explicitly required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_...

Open

16415

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

16416

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded as required. Source...

Open

16417

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

16418

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

16419

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. No source fully prohibits intermet...

Open

16420

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

16421

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

16422

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

16423

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) performed in accordance with ISO 17781; requirement not confirmed in the provided documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

16424

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

16425

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

16426

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

16427

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is confirmed for the specified pipe dimensions; calibration notches are assumed to follow ASTM E213 as the standard is accepted. Source: DMV_STANDARD_BOOK/12 - Special Te...

Open

16428

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, UT) is confirmed, but compliance with additional NORSOK M-630 MDS D51 or M-650/ISO 17782 requirements is not demonstrated. For OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic test...

Open

16429

5.2

AI

No

add date

No provided documentation confirms that indications greater than the calibration notch are classified as defects requiring rejection or repair; acceptance criteria and NDE procedures are not explicitly detailed for this requirement. Source: Digest AS...

Open

16430

6.0

AI

No

add date

Dimensional tolerances for the specified pipe are per ASTM A790, which references ASTM A999 for tolerances; no overriding tolerances are specified in the client inquiry or TechnipFMC documentation. Source: DMV_STANDARD_BOOK/07-01 - General informatio...

Open

16431

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORS...

Open

16432

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 (§14), requiring full traceability to melt and heat treatment lot. Marking methods include heat number and DMV lot number, ensuring traceability as required for all pipes at the Montbard p...

Open

16433

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated in NORSOK MDS D51 Rev 06, §14 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK...

Open

16434

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

16435

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body established within the EEA, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 ...

Open

16436

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

16437

10.2

AI

No

add date

None of the provided sources confirm that documentation traceable to the delivered products (such as part report or drawing per SIR205) will be transmitted to TechnipFMC as required. Certification and documentation types are mentioned, but explicit t...

Open

16438

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

16439

10.2

AI

No

add date

No source provides all required documentation and certification details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all met...

Open

16440

1.0

AI

No

add date

DMV 25.7N seamless pipe is compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification for the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

16441

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51...

Open

16442

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, with qualification testing meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_S...

Open

16443

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis for DMV 25.7N conforms to Table 2 of ASTM A790 and NORSOK MDS D51 Rev 6. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16444

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as specified in Table 2 and required by ASTM A790 and NORSOK MDS D51 Rev 6. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 R...

Open

16445

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnace qualification per NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N, and certification will include heat treatment con...

Open

16446

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16447

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dige...

Open

16448

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure, with specified locations and directions, is fulfilled for DMV 25.7N pipes. The...

Open

16449

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with required properties (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and maximum hardness specified; DMV 25.7N complies with these requirements. Source: DMV_STANDARD_BOOK/02 -...

Open

16450

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16451

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) per NORSOK MDS D51 Rev 6 and ASTM A790 requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

16452

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the requested pipe dimensions, meeting the requirement for wall thickness and testing standards. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products...

Open

16453

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C with minimum transverse values of 45 J (average) and 35 J (single), and longitudinal values of 65 J (average) and 50 J (single) if transverse i...

Open

16454

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, with etching using 20-40% NaOH or KOH after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

16455

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is explicitly required for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifi...

Open

16456

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

16457

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

16458

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

16459

4.4.2

AI

No

add date

Micrographic examination requires reporting of centerline intermetallic stringers, with acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

16460

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is...

Open

16461

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

16462

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

16463

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

16464

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

16465

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

16466

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781 (G48 Method A @ 50°C, 24h). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Diges...

Open

16467

5.1

AI

No

add date

No information is provided regarding the qualification, certification, or defined roles and responsibilities of NDE personnel to ISO 9712 level II or III or equivalent. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montb...

Open

16468

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive tes...

Open

16469

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782 are not addressed. For the specified OD (219.1 mm), eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at extra cost. No confirma...

Open

16470

5.2

AI

No

add date

No provided document explicitly confirms that any indication greater than the calibration notch is considered a defect requiring rejection or repair, and standard NDE methods are not feasible for the requested OD at Montbard. Source: DMV_STANDARD_BOO...

Open

16471

6.0

AI

No

add date

Dimensional tolerances for the requested ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with OD, WT, and ovality tolerances confirmed for the relevant dimensions. No deviations or special tolerances are specified in the customer req...

Open

16472

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the specification requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16473

8.0

AI

No

add date

Marking includes heat number and DMV lot number using indelible ink and vibro-etching, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 (§14) and standard practice for MST-Tubes. Source: Digest NORSOK MDS D51 Rev 06....

Open

16474

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16475

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

16476

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

16477

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

16478

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

16479

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing the relevant standards and documentation requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Dig...

Open

16480

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements: Charpy V-notch testing at -46°C, minimum transverse absorbed energy 45 J (average) and 35 J (single), minimum longitudinal absorbed energy 65 J (average) and 50 J (single) if transvers...

Open

16481

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 (or ISO 17782), meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

16482

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, chemical analysis results, solution annealing temperature/ho...

Open

16483

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with all mechanical, chemical, testing, and qualification requirements met, including M-650 qualification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

16484

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

16485

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16486

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed to conform per heat analysis. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 790.do...

Open

16487

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

16488

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

16489

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dige...

Open

16490

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations per NORSOK MDS D51/ASTM A790. F...

Open

16491

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the specified tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

16492

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

16493

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the requested pipe size and wall thickness (18.26mm), with referenced standards applicable for this product and plant. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03...

Open

16494

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, DMV_STANDARD_B...

Open

16495

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, including etching for intermetallic phases and ferrite balance using the specified solution after final polishing. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

16496

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

16497

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

16498

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781, with etching to detect intermetallic phases at a minimum magnification of 400x, and photos are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STANDARD_B...

Open

16499

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

16500

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

16501

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size, so ...

Open

16502

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - ...

Open

16503

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

16504

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

16505

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

16506

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, chemical composition, ferrite content, and corrosion/impact requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

16507

4.5

AI

No

add date

Corrosion test for DMV 25.7N is performed per ISO 17781: G48 Method A at 50°C for 24 hours, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/...

Open

16508

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

16509

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is confirmed for the specified pipe dimensions, with testing performed after all processing. Calibration is expected to follow ASTM E213 requirements. Source: DMV_STANDARD_BOOK/12 - Spe...

Open

16510

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially addressed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are fulfilled. For OD 219.1 mm, eddy current testing is not feasible,...

Open

16511

5.2

AI

No

add date

The specific requirement that any indication greater than that produced by the calibration notch represents a defect, with defective pipe and tubing to be rejected or repaired, is not explicitly stated or confirmed in the referenced documents. NDE me...

Open

16512

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and ASTM A999 as required, with no overriding specifications from TechnipFMC indicated. Requirement is fulfilled as tolerances follow the applicable ASTM standard for the specified pipe size and grade. Source:...

Open

16513

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16514

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790, both requiring full traceability to melt and heat treatment lot. Marking methods (indelible ink, vibro-etching) include heat and lot numbers, and certification per EN 10204 3.1 provides supporting...

Open

16515

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required in NORSOK MDS D51 Rev 06 (§13, §14) for ASTM A790 and DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16516

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

16517

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers as specified in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

16518

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the requirement for qualification for the sp...

Open

16519

10.2

AI

No

add date

Certification includes EN 10204 type 3.1 with traceability to product, NORSOK M-650/ISO17782 qualification, and ISO 9001 certification by a competent body, fulfilling documentation and traceability requirements for delivered products (SIR205). Source...

Open

16520

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided as standard, including all information required by ASTM A790 and NORSOK M-630, and validated by Quality Control at the Montbard plant. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, D...

Open

16521

10.2

AI

No

add date

No provided documentation explicitly confirms the inclusion of NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, ladle chemical analysis, solution annealing temperature/...

Open

16522

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - ...

Open

16523

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

16524

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with lot defined per ASTM A790 §9.1. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

16525

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and lot requirements for destructive testing, directly matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

16526

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations. Ordere...

Open

16527

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, with DMV 25.7N meeting the required tensile (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NO...

Open

16528

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: yield ≥ 550 MPa, tensile ≥ 750 MPa, elongation ≥ 25%, hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

16529

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the requested pipe dimensions, which exceed the minimum wall thickness required for transverse specimens. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished...

Open

16530

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum absorbed energies (transverse: 45 J average, 35 J single; longitudinal: 65 J average, 50 J single if transverse not possible), and su...

Open

16531

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, including etching for intermetallic phases and ferrite balance using the specified solution after final polishing. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

16532

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

16533

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

16534

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported, fulfilling the requirement to note and record the presence a...

Open

16535

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

16536

4.4.2

AI

No

add date

Micrographic examination requires reporting of centerline intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

16537

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully met. Source: ...

Open

16538

4.4.3

AI

No

add date

Ferrite content is checked per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing method and standard alignment. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

16539

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: microstructure examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides r...

Open

16540

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

16541

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided; neither the test nor the standard is referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests...

Open

16542

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, with manufacturing and qualification processes compliant with NORSOK M-650/ISO 17782. Sour...

Open

16543

4.5

AI

No

add date

Corrosion test per ISO 17781: G48 Method A at 50°C for 24 hours is performed on DMV 25.7N, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and DMV 25.7N complies with these requirements. Source: DMV_STANDARD_BO...

Open

16544

5.1

AI

No

add date

No information is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feas...

Open

16545

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available, including reference notches as specified, and pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non des...

Open

16546

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially met with 100% hydrostatic or NDE (EC or UT) testing, but there is no explicit evidence of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements. For OD 219.1...

Open

16547

5.2

AI

No

add date

No document explicitly states that any indication greater than the calibration notch is considered a defect requiring rejection or repair, nor confirms standard feasibility of such NDE for the specified dimensions at Montbard. Source: Digest ASTM A 7...

Open

16548

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are per ASTM A790 and ASTM A999 as required, with no deviations specified by the client or in the context. Requirement is fulfilled per applicable ASTM standards unless otherwise stated, which is not the...

Open

16549

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16550

8.0

AI

No

add date

Marking is performed according to ASTM A790 (§14) and includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-...

Open

16551

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 explicitly states 'Weld repairs not acceptable,' directly fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16552

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

16553

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

16554

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness for the specified size and product form. Source: DMV_STANDARD_BOO...

Open

16555

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products, fulfilling the requirement for transmission to TechnipFMC as per SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

16556

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications and practices. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D...

Open

16557

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and non-destructive te...

Open

16558

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Diges...

Open

16559

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782, as required. No evidence of QTR/MPCR availability is provided. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, 02-03-01 - Digest ASTM A 790.docx, 14-03 - Certification Mo...

Open

16560

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

16561

3.1

AI

No

add date

AOD or equivalent refining is required and applied for 100% of production, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16562

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and DMV material composition conforms with supplier certification and heat analysis per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02...

Open

16563

3.2

AI

No

add date

Solution annealing followed by accelerated cooling per ASTM A790 is confirmed; manufacturing process and furnaces are qualified per NORSOK M-650/ISO 17782; free circulation of heating/cooling media is implicit in compliance with these standards. Sour...

Open

16564

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

16565

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for sampling requirements, fulfilling the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03...

Open

16566

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16567

4.1

AI

No

add date

DMV 25.7N seamless pipes are tested for tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure at specified locations and directions. For the ordered pipe (OD 219...

Open

16568

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

16569

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required in Table 4 for NORSOK MDS D51 Rev 6 and ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

16570

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370/ISO 148-1 is feasible for the requested pipe dimensions and wall thickness, meeting the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Im...

Open

16571

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if transverse...

Open

16572

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, fulfilling the requirement. Source: DMV_STANDARD...

Open

16573

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases is required, in accordance with ISO 17781 Appendix B, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

16574

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

16575

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781, with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included; presence and location of intermetallic phases are noted and recorded as required. Sourc...

Open

16576

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

16577

4.4.2

AI

No

add date

Findings of intermetallic stringers must be reported, and acceptance is based on CVN and corrosion test results, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

16578

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10µm, which does not fully prohibit intermetallic phases/precipitates as required when CVN testing cannot be completed due to geometry or size. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NO...

Open

16579

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Sou...

Open

16580

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), and acceptance based on impact and cor...

Open

16581

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782; no confirmation of QTR/MPCR availability. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16582

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) performed in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

16583

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive tests, microstructure, and ferrite content requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16584

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

16585

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

16586

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the requested pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

16587

5.2

AI

No

add date

NDE per ASTM A790 is feasible with extra cost and technical advisor approval for the requested OD and length, but standard plant capabilities do not fully cover required NDE methods (EC, UT, hydrostatic) for this dimension, and there is no explicit e...

Open

16588

5.2

AI

No

add date

None of the relevant documents explicitly confirm that any indication greater than that produced by the calibration notch is considered a defect, nor do they specify that defective pipe and tubing shall be rejected or repaired according to this crite...

Open

16589

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790 referencing ASTM A999) unless otherwise specified, with no evidence of override in the customer specification. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STAND...

Open

16590

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that seamless pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORS...

Open

16591

8.0

AI

No

add date

Marking per ASTM A790 includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13-02-01 - Standa...

Open

16592

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly prohibits weld repairs under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NOR...

Open

16593

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

16594

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

16595

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02...

Open

16596

10.2

AI

No

add date

No explicit confirmation that documentation traceable to the products (SIR205) will be transmitted to TechnipFMC as required. Certification and documentation types are mentioned, but not the specific transmission and traceability per SIR205. Source: ...

Open

16597

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

16598

10.2

AI

No

add date

Documentation and certification requirements are not fully met: NORSOK M-650/ISO 17782 identification, QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and complete metallurgical and non-d...

Open

16599

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 -...

Open

16600

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

16601

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16602

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790, matching the specified requirements. Heat analysis is performed per heat as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 ...

Open

16603

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is covered by compliance...

Open

16604

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790, with test frequency '1/lot'. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

16605

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, directly referencing Table 3 for sampling as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM ...

Open

16606

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure tests are performed as specified. For the ord...

Open

16607

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

16608

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required by NORSOK MDS D51 Rev 6 and ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

16609

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370/ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, meeting the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Im...

Open

16610

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C, minimum average/single values of 45/35 J (transverse) and 65/50 J (longitudinal) for thickness >6mm, with specified reduction factors for sub-...

Open

16611

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, including etching for intermetallic phases and ferrite balance using the specified solution after final polishing. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

16612

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

16613

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

16614

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

16615

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

16616

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

16617

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Source: DMV_STANDARD_BOOK/02-04-03...

Open

16618

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

16619

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

16620

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

16621

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

16622

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16623

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A @ 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and complies with these requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

16624

5.1

AI

No

add date

No evidence is provided confirming NDE personnel are qualified and certified to ISO 9712 level II or III, nor are their roles and responsibilities defined as per ISO 9712 or equivalent. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing fea...

Open

16625

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782, as required. No evidence of QTR/MPCR availability is provided. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16626

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within machine capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 - U...

Open

16627

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790/NORSOK M-630 MDS D51/ISO 17782 are not fully addressed or feasible for the requested pipe dimensions at Montbard. Standard NDE methods (ultrasonic, eddy current, hydrostatic, dye penetrant) are either not fully a...

Open

16628

5.2

AI

No

add date

None of the relevant documents explicitly confirm that any indication greater than that produced by the calibration notch is treated as a defect and that defective pipe and tubing are rejected or repaired according to this criterion. NDE acceptance c...

Open

16629

6.0

AI

No

add date

Dimensional tolerances for the requested pipe are per applicable ASTM standards (ASTM A790/A999) as required, with no override specified by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances...

Open

16630

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16631

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods (indelible ink, vibro-etching) include heat and DMV lot numbers, ensuring traceability. Certification per EN 10...

Open

16632

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

16633

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

16634

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the specified quality-assurance system requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

16635

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, fulfilling supplier qualification documentation require...

Open

16636

10.2

AI

No

add date

No provided document confirms that the required documentation (including part report or drawing) will be transmitted to TechnipFMC and traceable to the delivered products as specified by SIR205. Certification and inspection documents are mentioned, b...

Open

16637

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

16638

10.2

AI

No

add date

All required documentation and certification details—NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of metallurgical and non-destructive testing—are ...

Open

16639

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the item table and confirmed by the digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-0...

Open

16640

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, fulfilling the requirement for manufacturer and process qualification and compliance with ...

Open

16641

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis for DMV 25.7N is compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16642

3.1

AI

No

add date

Chemical composition for UNS S32760 conforms to Table 2 of ASTM A790 as required, with heat analysis and supplier certification provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03...

Open

16643

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

16644

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as required by ASTM A790 and NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

16645

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and explicit reference to Table 3, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 ...

Open

16646

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specified locations and...

Open

16647

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with mechanical properties meeting Table 4 requirements (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%). Hardness testing is also performed and results are provided. Source: DMV_S...

Open

16648

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 06 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16649

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 and ISO 148-1 is feasible for the specified pipe dimensions, as the wall thickness (18.26 mm) exceeds the minimum required for both standards. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished prod...

Open

16650

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if transverse...

Open

16651

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed according to ISO 17781, with specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

16652

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

16653

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

16654

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

16655

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

16656

4.4.2

AI

No

add date

Micrographic examination requires reporting of centerline intermetallic stringers, with acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

16657

4.4.2

AI

No

add date

No provided documentation fully prohibits intermetallic phases and/or precipitates if CVN testing cannot be completed; the closest source allows isolated precipitates below 10µm, which does not meet the stricter client requirement. Source: DMV_STANDA...

Open

16658

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

16659

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: microstructure examination per ISO 17781, etching procedures, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides ...

Open

16660

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is fulfilled for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

16661

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

16662

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16663

4.5

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 (ISO 17781, G48 Method A) requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² for corrosion testing. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

16664

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, nor that their roles and responsibilities are defined as per ISO 9712 in the provided documents. Source: DMV_STANDARD_BOOK/12-02-...

Open

16665

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects is performed after all mechanical processing, heat treatments, and straightening, in accordance with ASTM E213 and ISO 10893-10. Calibration notches are introduced per Figure 3 of ASTM E213 within spec...

Open

16666

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially met with 100% hydrostatic or NDE (EC or UT) testing, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the requ...

Open

16667

5.2

AI

No

add date

None of the referenced documents explicitly confirm that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor do they detail the specific NDE acceptance criteria for this requirement. NDE feasibilit...

Open

16668

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790 and ASTM A999 as required, with no overriding tolerances specified by TechnipFMC. Requirement is fulfilled for the specified size and product type. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DM...

Open

16669

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: ASTM A790 digest, NORSOK MDS D51 Rev 06 digest.

Open

16670

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods (indelible ink, vibro-etching) include heat and DMV lot numbers, ensuring compliance for all pipes. Source: Dig...

Open

16671

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' directly fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 R...

Open

16672

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

16673

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the required quality-assurance system specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORS...

Open

16674

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

16675

10.2

AI

No

add date

No evidence that documentation traceable to the products will be transmitted to TechnipFMC as required by SIR205. Certification and documentation types are described, but specific transmission and traceability to TechnipFMC are not confirmed. Source:...

Open

16676

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference). Source: DMV_STANDARD_BOOK/02-04-0...

Open

16677

10.2

AI

No

add date

No provided documentation includes all required items: NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or complete metallurgical and non-destructive test results....

Open

16678

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, Digest NORSOK ...

Open

16679

1.0

AI

No

add date

Supplier qualification to both NORSOK M-650 and ISO 17782 is not confirmed; only M-650 accreditation is mentioned, and ISO 17782 accreditation is missing. Availability of QTR/MPCR for review is not demonstrated. Source: DMV_STANDARD_BOOK/02-04-03 - D...

Open

16680

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

16681

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard and required, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16682

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition and PREN requirements specified in Table 2, as per ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NOR...

Open

16683

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Requirement for free circulation of heating/cooling ...

Open

16684

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16685

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

16686

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and pieces, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

16687

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed as required, with test loc...

Open

16688

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

16689

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) per NORSOK MDS D51 Rev 6 and ASTM A790 requirements. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MD...

Open

16690

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and meets the minimum wall thickness requirements of the standards. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished product...

Open

16691

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements: Charpy V-notch testing at -46°C, minimum absorbed energies (transverse: 45 J average/35 J single; longitudinal: 65 J average/50 J single if transverse not possible) for thickness ≥6 mm...

Open

16692

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed according to ISO 17781, with specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

16693

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is specified for micrographic examination to show ferrite balance and intermetallic phases. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

16694

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

16695

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

16696

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

16697

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

16698

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fulfilled. Source: DMV_STANDARD_...

Open

16699

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

16700

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

16701

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781 with specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), fulfilling the requirement f...

Open

16702

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

16703

4.5

AI

No

add date

Corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is not explicitly confirmed; neither the test nor the standard is referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Mont...

Open

16704

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

16705

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss < 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest ...

Open

16706

5.1

AI

No

add date

No information is provided regarding the qualification, certification, or roles and responsibilities of NDE personnel to ISO 9712 level II or III or equivalent. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Montbard plan...

Open

16707

5.2

AI

No

add date

Ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, performed after all mechanical processing, heat treatment, and straightening, with reference notches in accordance with ASTM E2...

Open

16708

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, UT) is detailed, but compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782 is not confirmed. Standard NDE is not available for OD 219.1 mm at Montbard; EC requires multi-elements probe and techn...

Open

16709

5.2

AI

No

add date

None of the referenced documents explicitly confirm that any indication greater than that produced by the calibration notch is considered a defect, nor do they specify the rejection or repair of such defective pipe and tubing as required by the speci...

Open

16710

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no evidence of a special tolerance request or override in the customer specification. Requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General...

Open

16711

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16712

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 (§14), both requiring full traceability to melt and heat treatment lot. Marking methods (indelible ink, vibro-etching) include heat and lot numbers, ensuring compliance for all pipes as st...

Open

16713

9.0

AI

No

add date

Weld repairs are explicitly not acceptable as stated in NORSOK MDS D51 Rev 06, §14 for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK...

Open

16714

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

16715

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the relevant wall thickness, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02...

Open

16716

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/...

Open

16717

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

16718

10.2

AI

No

add date

Most required documentation and certification details (NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and test results) are stated as included in the EN 10204 3....

Open

16719

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all relevant mechanical, chemical, and testing requirements. Manufacturing is M-650 qualified for the required wall thickness. Source:...

Open

16720

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no evidence of ISO 17782 qualification or availability of QTR/MPCR documentation for review as required by the specification. Source: DMV_ST...

Open

16721

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

16722

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16723

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including all specified element limits and PRE ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 R...

Open

16724

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is covered by compliance...

Open

16725

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

16726

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dige...

Open

16727

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled, including tensile (longitudinal or transverse), hardness, CVN (transverse, longitudinal if not possible), corrosion, and microstructure tests at specified thickness locations...

Open

16728

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

16729

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) per NORSOK MDS D51 Rev 6 and ASTM A790 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

16730

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the requested pipe dimensions (WT 18.26mm > 6mm), fulfilling the requirement. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

16731

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse absorbed energy (average/single) 45 J/35 J, and longitudinal (average/single) 65 J/50 J if transverse not possible. The sp...

Open

16732

4.4.1

AI

No

add date

Micrographic examination is performed according to ISO 17781, with etching for intermetallic phases and ferrite balance using 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and examination as speci...

Open

16733

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is explicitly required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_...

Open

16734

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

16735

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

16736

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

16737

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 requires reporting of intermetallic phases, with acceptance based on CVN and corrosion test results if stringers are present, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D5...

Open

16738

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully met. Source: DMV_S...

Open

16739

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

16740

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed for DMV 25.7N, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m²; DMV 25.7N complies with these requirements. Source: DMV_STANDARD_BOOK/02-04-03 ...

Open

16741

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, including etching methods, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impac...

Open

16742

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

16743

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

16744

4.5

AI

No

add date

DMV 25.7N (UNS S32760) meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, ferrite content, and qualification per NORSOK MDS D51 Rev 6, ASTM A790, and N...

Open

16745

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

16746

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in...

Open

16747

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions; requirement is fulfilled. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

16748

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled. Provided documentation only details NDE per ASTM A790/A999, lacks explicit confirmation of NORSOK compliance, and indicates limitations or unc...

Open

16749

5.2

AI

No

add date

None of the provided sources explicitly confirm that indications greater than the calibration notch are treated as defects and that defective pipe and tubing are rejected or repaired as required. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790...

Open

16750

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are per ASTM A790/A999 as specified in the inquiry and confirmed by DMV documentation, with no deviations or special tolerances stated by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information...

Open

16751

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16752

8.0

AI

No

add date

Marking per ASTM A790 and standard plant methods includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK...

Open

16753

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly prohibits weld repairs under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NOR...

Open

16754

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

16755

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body as per the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

16756

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements of Table 2, including PREN ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16757

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, fulfilling the qualification requirement. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

16758

10.2

AI

No

add date

Certification includes EN 10204 type 3.1 with traceability to heat treatment, steel manufacturer, melting/refining practice, and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, fulfilling the requirement for documentation traceable to the ...

Open

16759

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification summary). Source: DMV_STANDARD_BOOK/02-04-03 ...

Open

16760

10.2

AI

No

add date

Documentation and certification requirements are not fully met: NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and complete metallurgical and non-destructive test r...

Open

16761

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the item table and confirmed by the digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, Digest NORSOK...

Open

16762

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16763

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process follows M-650 (or ISO 17782) qualified procedures, fulfilling the requirement for manufacturer and process qualification and meeting N...

Open

16764

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16765

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits and PREN minimum specified in Table 2, and meets the requirements of ASTM A790 and NORSOK MDS D51 Rev 06. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51...

Open

16766

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Requirement for free circulation of heating/cooling ...

Open

16767

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790, with test frequency specified as '1/lot'. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

16768

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

16769

4.1

AI

No

add date

Test sampling requirements for seamless pipes per NORSOK MDS D51/ASTM A790, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure tests at specified thickness location...

Open

16770

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

16771

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16772

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

16773

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness (>6mm), fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - ...

Open

16774

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements: Charpy V-notch testing at -466C with minimum average/single values of 45/35 J (transverse) and 65/50 J (longitudinal if transverse not possible), including reduction factors for sub-s...

Open

16775

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed according to ISO 17781, with specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 -...

Open

16776

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, as per ISO 17781 Appendix B, is explicitly required and matches the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

16777

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

16778

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781, with etching to detect intermetallic phases at a minimum magnification of 400x, and photos are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STANDARD_B...

Open

16779

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

16780

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, matching the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

16781

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully met. Source: DMV_STANDAR...

Open

16782

4.4.3

AI

No

add date

Ferrite content is determined per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination by these methods in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

16783

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, including etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and co...

Open

16784

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.doc...

Open

16785

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

16786

4.5

AI

No

add date

DMV 25.7N meets all metallurgical property acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO 17782 qualification, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite conten...

Open

16787

5.1

AI

No

add date

No evidence is provided confirming NDE personnel are qualified and certified to ISO 9712 level II or III, nor are their roles and responsibilities as defined in ISO 9712 addressed. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibil...

Open

16788

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-02-03 -...

Open

16789

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are met, but there is no explicit confirmation of compliance with the more stringent NDE requirements of NORSOK M-630 MDS D51 or M-650/ISO 17782. For the requested OD (219.1 mm), eddy current testing is not feasi...

Open

16790

5.2

AI

No

add date

None of the referenced documents explicitly confirm that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor do they specify this acceptance criterion for NDE. Source: Digest ASTM A 790.docx, Diges...

Open

16791

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standards (ASTM A999), with OD, WT, and ovality tolerances confirmed as compliant and no override by TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc...

Open

16792

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16793

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790, ensuring full traceability to melt and heat treatment lot. Marking methods include heat number and lot number as required by the standards and plant procedures, fulfilling the requirement. Source:...

Open

16794

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states 'Weld repairs not acceptable' under 'Surface finish / Repairs of defects', fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16795

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

16796

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

16797

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size ...

Open

16798

10.2

AI

No

add date

Certification includes EN 10204 type 3.1 with traceability to product, and MST-Tubes is ISO 9001 certified, fulfilling documentation and traceability requirements for delivered products (SIR205). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

16799

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

16800

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, including etching for intermetallic phases and ferrite balance using the specified solution after final polishing. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

16801

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16802

10.2

AI

No

add date

EN 10204 type 3.1 certificate will include most required information (NORSOK M-650/ISO 17782 QTR number, steel melting practice, heat treatment, etc.), but only the country of origin of the steel supplier is provided, not the actual steel producer's ...

Open

16803

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as required for 25 Cr Duplex stainless steel seamless pipes. Manufacturing is M-650 qualified for the specified wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

16804

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N (up to specified wall thicknesses) but not to ISO 17782, and there is no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev...

Open

16805

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

16806

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16807

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat to ensure compliance. Sour...

Open

16808

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnace qualification per NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is cove...

Open

16809

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot, with 'lot' defined according to ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

16810

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

16811

4.1

AI

No

add date

DMV 25.7N seamless pipes are tested for tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure at specified thickness locations. For the ordered pipe (OD 219.1 mm...

Open

16812

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

16813

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required in Table 4. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16814

4.3

AI

No

add date

Pipe wall thickness (18.26 mm) exceeds minimum required for Charpy V-notch testing per ASTM and ISO standards; testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible and fulfilled. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finishe...

Open

16815

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if transverse...

Open

16816

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

16817

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

16818

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs are included noting and recording the presence and location of intermetallic phases. So...

Open

16819

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Source: DMV_STANDAR...

Open

16820

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

16821

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

16822

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

16823

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, including etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and co...

Open

16824

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

16825

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

16826

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including chemical composition (PRE ≥ 40), mechanical properties, microstructure, ferrite content (35-60%), corrosion resistance (G48), and M-650 qualification for the re...

Open

16827

4.5

AI

No

add date

Requirement for no pitting at 20X magnification and weight loss less than 1.0 g/m² is fulfilled per compliance with ISO 17781 G48 Method A for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

16828

5.1

AI

No

add date

No evidence is provided confirming NDE personnel are qualified and certified to ISO 9712 level II or III, nor are their roles and responsibilities defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Mo...

Open

16829

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, performed after all mechanical processing, heat treatment, and straightening. Calibration notches per ASTM E213 Figure 3 a...

Open

16830

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV25.7N but not to ISO 17782; no evidence of QTR/MPCR availability. Requirement for qualification to both NORSOK M-650/ISO 17782 and documentation availability is not fulfilled. Source: DMV_STANDARD_BOOK/02...

Open

16831

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

16832

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51 Rev 6/NORSOK M-650/ISO 17782 are not fully met: provided information only covers ASTM A790/A999 NDE, not the additional NORSOK requirements; eddy current and ultrasonic testing for OD 219...

Open

16833

5.2

AI

No

add date

The available documents do not confirm that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor do they specify that NDE will be performed as standard for the requested dimensio...

Open

16834

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790 referencing ASTM A999) unless otherwise specified, with no evidence of override by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-0...

Open

16835

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both specify that finished seamless pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Dig...

Open

16836

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot, and standard marking methods (indelible ink, vibro-etching) include heat number and DMV lot number as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D5...

Open

16837

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly required under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pro...

Open

16838

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

16839

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement in section 10.0 of the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

16840

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness, fulfilling the qualification requirement. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

16841

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

16842

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificatio...

Open

16843

10.2

AI

No

add date

Most required documentation elements (NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, metallurgical and non-destructive test results) are either missing or only refe...

Open

16844

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, as confirmed by specification references and digest. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16845

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Requirement for free circulation of heating/cooling ...

Open

16846

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with lot defined per ASTM A790 §9.1. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

16847

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, directly referencing the table for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detai...

Open

16848

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specified thickness loc...

Open

16849

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

16850

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required in Table 4 for NORSOK MDS D51 Rev 6 and ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

16851

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for wall thickness >6mm in both longitudinal and transverse directions for the specified pipe dimensions, meeting the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testi...

Open

16852

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C with minimum transverse values of 45 J (average) and 35 J (single), and longitudinal values of 65 J (average) and 50 J (single) if transverse ...

Open

16853

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, including etching for intermetallic phases and ferrite balance using the specified solution after final polishing. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

16854

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

16855

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

16856

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 is performed at ≥400x magnification, with etching to detect intermetallic phases; presence and location are noted and recorded with micrographs. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

16857

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

16858

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

16859

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fulfilled. Source: DMV_S...

Open

16860

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Sou...

Open

16861

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

16862

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16863

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the available documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

16864

4.5

AI

No

add date

DMV 25.7N meets the acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 06, including compliance with destructive and micrographic tests, manufacturing, heat treatment, and qualification requirements. Source: DMV_STANDARD_BOOK/02 ...

Open

16865

4.5

AI

No

add date

DMV 25.7N undergoes pitting corrosion testing per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD...

Open

16866

5.1

AI

No

add date

No information is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feas...

Open

16867

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

16868

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially addressed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are fulfilled. Standard NDE methods are not available for the request...

Open

16869

5.2

AI

No

add date

None of the relevant documents explicitly confirm that any indication greater than that produced by the calibration notch is considered a defect requiring rejection or repair of pipe/tubing as specified in the requirement. NDE is referenced, but the ...

Open

16870

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as required, with no overriding specification from TechnipFMC. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - Tolerances according to ASTM A 790-02 (A 999-01).doc,...

Open

16871

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16872

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790, ensuring full traceability to melt and heat treatment lot. Marking methods include heat number and lot number as standard content. Certification per EN 10204 3.1 includes heat treatment and steelm...

Open

16873

9.0

AI

No

add date

Weld repairs are explicitly stated as not acceptable for DMV 25.7N in the relevant specification section covering NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

16874

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

16875

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, meeting the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-0...

Open

16876

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

16877

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

16878

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided, including all information required by ASTM A790 and NORSOK M-630. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certification Montbard plant.doc

Open

16879

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing temperature/holding/quench medium, or results of metallurgical and no...

Open

16880

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

16881

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but is not accredited to ISO 17782 as required; full qualification per both standards is not demonstrated for the supplied product. QTR/MPCR availability is not confirmed. Source: DMV_STANDARD_BOOK...

Open

16882

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

16883

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16884

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PREN ≥ 40, as specified by ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 -...

Open

16885

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Requirement for free circulation of heating/cooling ...

Open

16886

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

16887

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and pieces, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01...

Open

16888

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations are per...

Open

16889

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required by NORSOK MDS D51 Rev 6 and ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

16890

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness, fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact ...

Open

16891

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C, minimum absorbed energy values (transverse: 45 J average, 35 J single; longitudinal: 65 J average, 50 J single if transverse not possible), an...

Open

16892

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, using 20-40% NaOH or KOH etchant after final polishing, fulfilling the requirement for metallographic preparation and examination as specified. Sourc...

Open

16893

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

16894

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10μm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collectio...

Open

16895

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and photos are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STANDARD_BO...

Open

16896

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included, actual magnification and scale bar reported, fulfilling the requirement for representative micrographs at or near mid-wall thickness if intermetallic phas...

Open

16897

4.4.2

AI

No

add date

Micrographic examination requires reporting of centerline intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

16898

4.4.2

AI

No

add date

The available documentation does not prohibit all intermetallic phases and/or precipitates if CVN testing cannot be completed; isolated precipitates below 10µm are permitted, which does not meet the zero-tolerance client requirement. Source: DMV_STAN...

Open

16899

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

16900

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781 with specified etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact an...

Open

16901

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

16902

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

16903

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including destructive, micrographic, ferrite, corrosion, and impact tests; manufacturing and qualification processes are accredited as required. Source: DMV_STANDARD_BOOK...

Open

16904

4.5

AI

No

add date

DMV 25.7N meets the requirement of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 ...

Open

16905

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source: DM...

Open

16906

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, including reference notches as specified. Pipe dimensions are within machine capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destruct...

Open

16907

5.2

AI

No

add date

NDE per ASTM A790 is partially addressed, but there is no explicit confirmation of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE criteria. For OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultr...

Open

16908

5.2

AI

No

add date

None of the relevant sources explicitly confirm that indications greater than the calibration notch are treated as defects requiring rejection or repair for the specified product and dimension; NDE acceptance criteria and standard rejection/repair pr...

Open

16909

6.0

AI

No

add date

Dimensional tolerances are per applicable ASTM standard (ASTM A790/A999) as required, with no override specified by TechnipFMC. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances according to ASTM A 312...

Open

16910

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require seamless pipes to be white pickled or bright annealed, directly fulfilling the requirement for finished pipes to have these surface conditions. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev...

Open

16911

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, ensuring full traceability to melt and heat treatment lot. Marking methods include heat number and DMV lot number, meeting the requirement for traceability. Source: DMV_STANDARD_BOOK/02-03-01 ...

Open

16912

9.0

AI

No

add date

Weld repairs are explicitly stated as not acceptable in the specification under 'Surface finish / Repairs of defects' (§13, §14). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

16913

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/...

Open

16914

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

16915

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, fulfilling the requirement. Source: DMV_STANDARD_BOOK/0...

Open

16916

10.2

AI

No

add date

Certification includes EN 10204 type 3.1 with traceability to heat treatment, steel manufacturer, melting/refining practice, and NORSOK M-650/ISO17782 qualification; MST-Tubes is ISO 9001 certified and certificates are traceable to delivered products...

Open

16917

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referenced in the relevant specifications. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

16918

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 qualification identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or specific metallurgical and non-destructi...

Open

16919

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03...

Open

16920

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not ISO 17782, as required. No evidence of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16921

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

16922

3.1

AI

No

add date

AOD or equivalent refining is standard and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16923

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat, confirming conformity to the required ...

Open

16924

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. Certification includes heat treatment condition as per ASTM A790. Pipes are processed to ensure fr...

Open

16925

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

16926

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for sampling requirements, fulfilling the specification for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

16927

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is performed as required. For t...

Open

16928

4.2

AI

No

add date

Tensile testing is performed at room temperature in accordance with ASTM A370 or ISO 6892-1, and the material meets the specified tensile and maximum hardness properties per Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

16929

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

16930

4.3

AI

No

add date

Pipe wall thickness (18.26 mm) exceeds minimum required for Charpy V-notch testing per ASTM and ISO standards; testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible and fulfilled. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finishe...

Open

16931

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal (if transvers...

Open

16932

3.1

AI

No

add date

AOD or equivalent refining is standard and required for 100% of production, and DMV 25.7N complies with the chemical composition requirements per Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

16933

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing, fulfilling the requirement. Source: DMV_STANDARD...

Open

16934

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution for micrographic examination to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

16935

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each precipitate is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

16936

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

16937

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

16938

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results if present. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

16939

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fully fulfilled. Source: DMV_S...

Open

16940

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Sou...

Open

16941

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

16942

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

16943

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including destructive and micrographic tests, chemical composition, ferrite content, and corrosion/impact requirements. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

16944

4.5

AI

No

add date

DMV 25.7N meets the requirement of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 ...

Open

16945

5.1

AI

No

add date

No evidence is provided confirming NDE personnel are qualified and certified to ISO 9712 level II or III, nor are their roles and responsibilities defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in Mo...

Open

16946

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

16947

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

16948

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

16949

5.2

AI

No

add date

NDE per ASTM A790 is detailed, but compliance with additional NORSOK M-630 MDS D51 and M-650/ISO 17782 requirements is not confirmed. For OD 219.1 mm at Montbard, eddy current, hydrostatic, and ultrasonic testing are only available at extra cost and ...

Open

16950

5.2

AI

No

add date

None of the provided sources explicitly confirm that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor do they detail the acceptance criteria for NDE indications relative to a calibration notch f...

Open

16951

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standards (including A999), with no override specified by TechnipFMC in the provided context. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 ...

Open

16952

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D...

Open

16953

8.0

AI

No

add date

Marking is performed according to ASTM A790 (§14) and includes heat number and DMV lot number using indelible black ink or vibro-etching, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Dige...

Open

16954

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

16955

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, meeting the requirement for an appropriate quality-assurance system certified by a competent body established within the EEA and specifically assessed for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

16956

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

16957

10.1

AI

No

add date

Supplier MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the requirement for qualification for t...

Open

16958

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products and transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

16959

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided, including all information required by ASTM A790 and NORSOK M-630, and validated by Quality Control for mill inspection. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BO...

Open

16960

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of metallurgical and non-de...

Open

16961

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, DMV_STANDARD_B...

Open

16962

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not to ISO 17782; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16963

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. The chemical composition table in the requirement matches the standard, and compliance is confirmed for DMV 2...

Open

16964

3.2

AI

No

add date

Pipes are solution annealed followed by water quenching per ASTM A790, furnaces are qualified to NORSOK M-650/ISO 17782, and pipe arrangement ensures free circulation of heating and cooling media during heat treatment including accelerated cooling. S...

Open

16965

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot, with lot defined per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

16966

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

16967

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, all per NORSOK MDS D51/ASTM A7...

Open

16968

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with material meeting the specified tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

16969

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-0...

Open

16970

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions, meeting the minimum wall thickness requirements for these standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive test...

Open

16971

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C with minimum transverse (average 45 J, single 35 J) and longitudinal (average 65 J, single 50 J) values, and sub-size reduction factors. The s...

Open

16972

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, including etching for intermetallic phases and ferrite balance using the specified solution after final polishing. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

16973

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

16974

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

16975

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 at a minimum magnification of 400x, with etching to detect intermetallic phases. The presence and location of intermetallic phases are noted and recorded with representative micrographs. Source: DMV...

Open

16976

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, actual magnification reported, and scale bar included if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

16977

4.4.2

AI

No

add date

The available documentation allows isolated intermetallic precipitates below 10µm, but does not prohibit all intermetallic phases and/or precipitates if CVN testing cannot be completed, as required by the client specification. Source: DMV_STANDARD_BO...

Open

16978

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for testing per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BO...

Open

16979

4.4.3

AI

No

add date

Micrographic examination is performed per ISO 17781 with specified etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact an...

Open

16980

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

16981

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

16982

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

16983

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A @ 50°C, 24h) is performed for DMV 25.7N with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and compliance is confirmed. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

16984

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor are roles and responsibilities defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-...

Open

16985

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is feasible and standards-compliant for the specified pipe dimensions; calibration notch requirements per ASTM E213 Figure 3 are covered by acceptance of the standard. Sou...

Open

16986

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT testing) is confirmed, but there is no explicit evidence of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782 NDE requirements. For OD 219.1 mm, eddy current testing is not feasible, h...

Open

16987

5.2

AI

No

add date

None of the provided sources explicitly confirm that any indication greater than that produced by the calibration notch is treated as a defect and that defective pipe and tubing are rejected or repaired according to this criterion. Acceptance criteri...

Open

16988

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed as per the applicable ASTM standard (ASTM A790) for the specified dimensions, with no deviations stated in the customer specification. Source: DMV_STANDARD_BOOK/07-01 - General information....

Open

16989

7.0

AI

No

add date

Finished pipes are required to be white pickled or bright annealed, which is explicitly specified in both ASTM A790 (section 6.1.3) and NORSOK MDS D51 Rev 06 (§13). Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-...

Open

16990

8.0

AI

No

add date

Marking includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required by ASTM A790 and NORSOK MDS D51 Rev 6. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/13...

Open

16991

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 explicitly states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

16992

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

16993

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the required quality-assurance system specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORS...

Open

16994

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the specified wall thickness, and QTR number is included as per M-650 qualification, fulfilling the requirement for NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR/MCPR...

Open

16995

10.2

AI

No

add date

Certification includes EN 10204 type 3.1 with traceability to heat treatment, steel manufacturer, melting/refining practice, and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, fulfilling the requirement for documentation traceable to the ...

Open

16996

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualification standards. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

16997

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of metallurgical and non-destructive testing. ...

Open

16998

1.0

AI

No

add date

DMV 25.7N seamless pipe is confirmed as compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, with M-650 qualification for the required wall thickness. All relevant mechanical, chemical, and testing requirements are met for the specified grade an...

Open

16999

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

17000

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis complies with Table 2 for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17001

3.1

AI

No

add date

Chemical composition for S32760 matches Table 2 of ASTM A790 as required, and DMV material conforms with supplier certification and heat analysis per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03...

Open

17002

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is implici...

Open

17003

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790, with test frequency specified as '1/lot'. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

17004

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

17005

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure tests at specified locations and directions. ...

Open

17006

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

17007

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

17008

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions (WT 18.26mm, OD 219.1mm), fulfilling the requirement. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

17009

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact requirements: Charpy V-notch testing at -46°C, minimum absorbed energies of 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal, and sub-size specimen reducti...

Open

17010

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, using the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

17011

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

17012

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

17013

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781, with etching to detect intermetallic phases at a minimum magnification of 400x, and photos are included; presence and location of intermetallic phases are noted and recorded. Source: DMV_STANDARD_B...

Open

17014

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

17015

4.4.2

AI

No

add date

Presence of centerline intermetallic stringers must be reported, and acceptance is based on CVN and corrosion test results as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

17016

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm if not distributed over the whole specimen, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geom...

Open

17017

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781 using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781....

Open

17018

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

17019

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17020

4.5

AI

No

add date

Corrosion testing is performed per ASTM G48 Method A (50°C, 24h) in accordance with ISO 17781, with criteria and procedure detailed and matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

17021

4.5

AI

No

add date

DMV 25.7N seamless pipe fulfills ASTM A790 and NORSOK MDS D51 Rev 06 metallurgical acceptance criteria, including destructive, micrographic, corrosion tests, ferrite content, heat treatment, and manufacturing process requirements. All main supplement...

Open

17022

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A @ 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and complies with these requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

17023

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Sources: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasib...

Open

17024

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, which are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-0...

Open

17025

5.2

AI

No

add date

NDE requirements per ASTM A790 are partially met, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE criteria are fulfilled. Standard NDE methods (EC, UT, hydrostatic) for the requested OD and length at Mo...

Open

17026

5.2

AI

No

add date

None of the relevant documents explicitly confirm that indications greater than the calibration notch are treated as defects requiring rejection or repair, and standard NDE is not feasible for the requested OD at Montbard. Source: Digest ASTM A 790.d...

Open

17027

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standards (ASTM A999), with no deviations or overrides indicated by TechnipFMC for the requested dimensions, fulfilling the requirement. Source: DMV_STANDARD_BOOK/07.01 - General i...

Open

17028

7.0

AI

No

add date

Finished pipes are required to be white pickled or bright annealed by both ASTM A790 (section 6.1.3) and NORSOK MDS D51 Rev 06 (§13), directly fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/...

Open

17029

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods include heat number and lot number as standard content, ensuring traceability is maintained. Source: DMV_STANDA...

Open

17030

9.0

AI

No

add date

Weld repairs are explicitly not acceptable as stated in the specification under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

17031

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

17032

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

17033

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification demons...

Open

17034

10.2

AI

No

add date

ISO 9001 certification is provided and documentation traceable to delivered products is included as required by SIR205 and specification section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 -...

Open

17035

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided, including all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 qualification reference). Source: DMV_STANDARD_BOOK/02-04-0...

Open

17036

10.2

AI

No

add date

Most required documentation and certification items (NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, metallurgical and NDT results) are stated as included in certifi...

Open

17037

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

17038

1.0

AI

No

add date

Manufacturing is referenced as according to a NORSOK M-650/ISO 17782 qualified procedure, but there is no explicit confirmation of supplier qualification for the exact product or availability of the full Qualification Test Record/MPCR for review by T...

Open

17039

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - ...

Open

17040

3.1

AI

No

add date

AOD or equivalent steel refining is required for 100% of production and DMV 25.7N complies with the chemical composition requirements per Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

17041

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. The chemical composition table matches the standard and compliance is confirmed for the proposed grade. Sourc...

Open

17042

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is covered...

Open

17043

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

17044

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and lot definition, directly matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

17045

4.1

AI

No

add date

Transverse CVN specimens are feasible for the ordered pipe dimensions, fulfilling the requirement for test sampling direction and location. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - ...

Open

17046

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with required tensile and hardness properties met as specified in Table 4. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17047

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

17048

4.3

AI

No

add date

Charpy V-notch testing is performed in accordance with ISO 17781 (equivalent to ISO 148-1), and the requested pipe dimensions exceed the minimum wall thickness required for testing per ASTM and ISO standards. Acceptance criteria and testing feasibili...

Open

17049

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 Charpy V-notch impact requirements at -46°C: minimum 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal if transverse not possible, and sub-size reduction factors a...

Open

17050

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

17051

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

17052

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

17053

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

17054

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

17055

4.4.2

AI

No

add date

Presence of centerline intermetallic stringers must be reported, and acceptance is based on CVN and corrosion test results as specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

17056

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm if not distributed over the whole specimen, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the ...

Open

17057

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

17058

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, including etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and co...

Open

17059

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

17060

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

17061

4.5

AI

No

add date

DMV 25.7N fulfills ASTM A790 and NORSOK MDS D51 Rev 6 acceptance criteria, including all metallurgical property requirements and qualification per NORSOK M-650/ISO 17782 for the specified dimensions. Source: DMV_STANDARD_BOOK/02-02-01 Digest summary ...

Open

17062

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

17063

5.1

AI

No

add date

No information is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destru...

Open

17064

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is performed after all mechanical processing, heat treatment, and straightening; pipe dimensions are within equipment capability; standards and procedures meet requirement including ref...

Open

17065

5.2

AI

No

add date

NDE per ASTM A790 is generally feasible, but NORSOK M-630 MDS D51 Rev 6 and NORSOK M-650/ISO 17782-specific NDE acceptance criteria are not validated. For OD 219.1 mm, standard NDE (eddy current, hydrostatic, ultrasonic) is not available or only poss...

Open

17066

5.2

AI

No

add date

The requirement that any indication greater than the calibration notch is a defect, with defective pipe/tubing to be rejected or repaired, is not explicitly stated or guaranteed in the referenced specifications or plant feasibility documentation for ...

Open

17067

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are confirmed as per ASTM A790 for the requested dimensions, with no override by TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances a...

Open

17068

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: ASTM A790, NORSOK MDS D51 Rev 06

Open

17069

8.0

AI

No

add date

Marking per ASTM A790 includes traceability to melt and heat treatment lot; marking methods (indelible ink, vibro-etching) include heat number and DMV lot number, ensuring full traceability. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 ...

Open

17070

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly prohibits weld repairs under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17071

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

17072

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

17073

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

17074

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products, meeting SIR205 requirements for transmission to TechnipFMC. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - D...

Open

17075

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, such as heat treatment condition, steel manufacturer, steel melting and refining practice, and relevant manufacturing summary identification...

Open

17076

10.2

AI

No

add date

All required documentation and certification details are either missing or only partially addressed. The EN 10204 3.1 certificate will include NORSOK M-650/ISO 17782 identification, steel melting practice, refining method, and heat treatment conditio...

Open

17077

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by specification references and digest documentation. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17078

1.0

AI

No

add date

Manufacturing is referenced as per NORSOK M-650/ISO 17782 qualified procedure, but there is no explicit confirmation of supplier qualification for the exact product supplied or availability of the full Qualification Test Record/MPCR for review by Tec...

Open

17079

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV 25.7N, with manufacturing processes qualified per NORSOK M-650 (or ISO 17782), and compliance with NORSOK M-630 MDS D51 Rev. 6 is referenced. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

17080

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17081

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Chemical composition matches the requirement table and is confirmed by supplier certification and heat analys...

Open

17082

3.2

AI

No

add date

Solution annealing followed by accelerated cooling per ASTM A790 is confirmed, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is covered by compliance wit...

Open

17083

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

17084

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and lot definition, directly matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

17085

4.1

AI

No

add date

Test sampling for DMV 25.7N seamless pipes includes tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness locations, all performed per NORSOK M-630...

Open

17086

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

17087

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

17088

4.3

AI

No

add date

Charpy V-notch impact testing is performed in accordance with ISO 17781 QL II at -46°C, which is an accepted alternative to ISO 148-1, and is feasible for the specified pipe size and wall thickness in both longitudinal and transverse directions. Sour...

Open

17089

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C, minimum absorbed energies of 45 J (average) and 35 J (single) transverse, 65 J (average) and 50 J (single) longitudinal, and reduction factors...

Open

17090

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

17091

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution for micrographic examination to show ferrite balance and intermetallic phases is required, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

17092

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

17093

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to note and record the presence and location of intermetallic phases. Source: DMV_STANDAR...

Open

17094

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

17095

4.4.2

AI

No

add date

Micrographic examination requires reporting of centerline intermetallic stringers, with acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

17096

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm if not distributed over the whole specimen, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geom...

Open

17097

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for testing methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

17098

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

17099

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17100

4.5

AI

No

add date

Pitting corrosion test per ISO 17781 using ASTM G48 Method A at 50°C for 24 hours is performed, meeting the requirement for corrosion testing in accordance with the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

17101

4.5

AI

No

add date

DMV 25.7N fulfills ASTM A790 and NORSOK MDS D51 Rev 6 acceptance criteria, including all metallurgical property requirements and relevant supplementary requirements. Source: DMV_STANDARD_BOOK/02-02-01 Digest summary of ASTM A.docx, DMV_STANDARD_BOOK/...

Open

17102

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781: G48 Method A at 50°C for 24 hours, matching the client's specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

17103

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

17104

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is confirmed, covering the required dimensional range and performed after all processing. Calibration requirements, including reference notches per ASTM E213, are considered fulfilled a...

Open

17105

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no evidence of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782 NDE requirements. For the requested OD (219.1 mm), eddy current and ultrasonic testing are only available at extra cost a...

Open

17106

3.1

AI

No

add date

AOD or equivalent refining is required and used for 100% of production, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17107

5.2

AI

No

add date

No provided document confirms that any indication greater than the calibration notch is treated as a defect requiring rejection or repair; NDE acceptance criteria and process capability do not fulfill the requirement for the specified OD 219.1 mm pip...

Open

17108

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790/A999) as required, with no overriding specification from TechnipFMC identified. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_STANDARD_BOOK/07-03-01 - Tolerances ...

Open

17109

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17110

8.0

AI

No

add date

Marking is performed according to ASTM A790 (§14) and standard plant practices, using indelible black ink or vibro-etching to include heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: Digest NORSOK MDS...

Open

17111

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

17112

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA with specific assessment for materials. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collecti...

Open

17113

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/0...

Open

17114

10.1

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760/DMV25.7N up to 31.75 mm WT, covering the required 18.26 mm, and the EN 10204 type 3.1 certificate will include the NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, dem...

Open

17115

10.2

AI

No

add date

Certification includes EN 10204 type 3.1 with traceability to heat treatment, steel manufacturer, melting/refining practice, and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, fulfilling the requirement for documentation traceable to the ...

Open

17116

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are provided as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 ...

Open

17117

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and results of all metallurgical and non-destructive testi...

Open

17118

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the item table and confirmed by the digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-0...

Open

17119

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782, and there is no confirmation of QTR/MPCR availability for review as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17120

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specific...

Open

17121

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the specified chemical composition limits and PREN ≥ 40 as per NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Di...

Open

17122

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnace compliance to NORSOK M-650/ISO 17782 qualified procedures. Certification includes heat treatment condition as per ASTM A790. Source: DMV...

Open

17123

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

17124

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency and direct reference to Table 3, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

17125

4.1

AI

No

add date

All required tests (tensile, hardness, CVN, corrosion, microstructure) are performed as specified for seamless pipes per NORSOK MDS D51 and ASTM A790, with correct test directions and thickness locations. For the ordered pipe dimensions, transverse C...

Open

17126

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

17127

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) per NORSOK MDS D51 Rev 6 and ASTM A790 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

17128

4.3

AI

No

add date

Charpy V-notch testing is performed in accordance with ISO 17781 (equivalent to ISO 148-1) and is feasible for the specified pipe dimensions under both ASTM and ISO standards, fulfilling the requirement for Charpy V-notch testing per ASTM A370, ASTM ...

Open

17129

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements, including Charpy V-notch testing at -46°C, minimum absorbed energy values, and sub-size reduction factors as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

17130

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

17131

4.4.1

AI

No

add date

Etching with 20–40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is required for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special pr...

Open

17132

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

17133

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

17134

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BO...

Open

17135

4.4.2

AI

No

add date

Presence of centerline intermetallic stringers must be reported, and acceptance is based on CVN and corrosion test results as specified. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17136

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not fully ...

Open

17137

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

17138

4.4.3

AI

No

add date

Micrographic examination requirements are fulfilled: examination per ISO 17781, specified etching, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported), with ...

Open

17139

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

17140

4.5

AI

No

add date

Applicable standards listed do not mention ASTM G48 or ISO 17781, and there is no explicit confirmation that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 will be performed. Source: DMV_STANDARD_BOOK/12-03-01- Cor...

Open

17141

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, with compliance to NORSOK M-650/ISO 17782 qualification processes. Source: DMV_STANDARD_BO...

Open

17142

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-...

Open

17143

5.1

AI

No

add date

No evidence provided regarding qualification or certification of NDE personnel to ISO 9712 level II or III, or their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-...

Open

17144

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, including reference notches as specified; pipe dimensions are within machine capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destruct...

Open

17145

5.2

AI

No

add date

NDE per ASTM A790/A999 (hydrostatic, EC, or UT) is confirmed, but compliance with additional NORSOK M-630 MDS D51 or M-650/ISO 17782 NDE requirements is not demonstrated. For OD 219.1 mm at Montbard, standard NDE is not available; hydrostatic and ult...

Open

17146

5.2

AI

No

add date

None of the provided documents confirm that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair; the specific NDE acceptance criterion is not addressed or confirmed for the requested...

Open

17147

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are per the applicable ASTM standard (ASTM A790) for the requested dimensions, with no specified deviations in the customer specification. Source: DMV_STANDARD_BOOK/07-01 - General information.doc, DMV_S...

Open

17148

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17149

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods include heat number and DMV lot number, ensuring compliance with the requirement for all pipes at the Montbard ...

Open

17150

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 explicitly states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17151

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

17152

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

17153

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified ...

Open

17154

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

17155

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is issued and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and compliant with specification requirements. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, 14-03 - Cer...

Open

17156

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, or results of all metallurgical and no...

Open

17157

1.0

AI

No

add date

DMV 25.7N (UNS S32760) seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, as confirmed by the specification digest and engineering data table. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_...

Open

17158

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782 as required; no evidence provided for QTR/MPCR availability for review by TechnipFMC as specified in the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51...

Open

17159

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

17160

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production; chemical analysis for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17161

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat, confirming conformity to the required...

Open

17162

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

17163

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot as defined in ASTM A790, matching the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 R...

Open

17164

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with a frequency of 1 per 100 pieces and per lot, matching the requirement that test specimen sampling is outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

17165

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), corrosion, and microstructure, is performed per NORSOK MDS D51/ASTM A790 with required locations and directi...

Open

17166

4.2

AI

No

add date

Tensile testing is performed at room temperature per required standards, with mechanical properties and hardness requirements matching Table 4; compliance with ASTM A370 or ISO 6892-1 and NORSOK MDS D51 is confirmed. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

17167

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW, fulfilling the client's mechanical requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

17168

4.3

AI

No

add date

Charpy V-notch testing is performed in accordance with ISO 148-1 (acceptable alternative to ASTM A370/A1058) at the required wall thickness and dimensions, with clear acceptance criteria and frequency specified. Source: DMV_STANDARD_BOOK/02-04-03 - D...

Open

17169

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse (average/single) 45 J/35 J, longitudinal (average/single) 65 J/50 J if transverse not possible, and specified reduction fa...

Open

17170

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, including etching for intermetallic phases and ferrite balance using the specified solution after final polishing. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

17171

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BO...

Open

17172

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

17173

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

17174

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, fulfilling the requirement for representative micrographs at or near mid-wall thickness. Source: DMV_STANDARD...

Open

17175

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 includes etching to detect intermetallic phases, with findings reported and acceptance based on CVN and corrosion test results, fulfilling the requirement for reporting centerline intermetallic stringers and bas...

Open

17176

4.4.2

AI

No

add date

The available specifications allow isolated intermetallic precipitates below 10μm if not distributed over the whole specimen, but do not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed, as required by the cl...

Open

17177

4.4.3

AI

No

add date

Ferrite content is determined per ASTM E562 or ASTM E1245, performed in accordance with ISO 17781, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK...

Open

17178

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

17179

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is fulfilled for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17180

4.5

AI

No

add date

No explicit confirmation of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

17181

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

17182

4.5

AI

No

add date

Corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) is performed with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m²; DMV 25.7N complies. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

17183

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in...

Open

17184

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects in accordance with ASTM E213 or ISO 10893-10 can be performed after all processing, and the equipment covers the required pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non des...

Open

17185

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed as fulfilled; provided documentation only covers ASTM A790/A999 NDE, destructive testing, or does not confirm feasibility for required OD and length. Standa...

Open

17186

5.2

AI

No

add date

None of the provided sources explicitly confirm that any indication greater than that produced by the calibration notch is considered a defect and that such pipe/tubing shall be rejected or repaired as required by the specification. Acceptance criter...

Open

17187

6.0

AI

No

add date

Dimensional tolerances for the requested pipe are per ASTM A790, which references ASTM A999 for tolerances. No override is specified in the customer documentation, so the requirement is fulfilled. Source: DMV_STANDARD_BOOK/07-01 - General information...

Open

17188

7.0

AI

No

add date

Finished pipes are required to be white pickled or bright annealed according to both ASTM A790 (section 6.1.3) and NORSOK MDS D51 Rev 06 (§13), directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17189

8.0

AI

No

add date

Marking is performed according to ASTM A999 §25 and ASTM A790 (§14), both requiring full traceability to melt and heat treatment lot. Marking methods (indelible ink, vibro-etching) include heat and DMV lot numbers, ensuring compliance for all pipes a...

Open

17190

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states 'Weld repairs not acceptable' under 'Surface finish / Repairs of defects', fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17191

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

17192

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

17193

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

17194

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to delivered products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK ...

Open

17195

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualifications as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51...

Open

17196

10.2

AI

No

add date

Documentation and certification details required by the specification—such as NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of metallurgical and non...

Open

17197

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and are M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 -...

Open

17198

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782 as required; no evidence of full qualification or availability of QTR/MPCR documentation for review as specified in the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest...

Open

17199

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

17200

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17201

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat, confirming conformity to the required ...

Open

17202

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and MST-Tubes is M-650 accredited for DMV 25.7N. Requirement for free circulation of heating/cooling ...

Open

17203

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot, with lot defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Spe...

Open

17204

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed dige...

Open

17205

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse or longitudinal if not feasible), and corrosion/microstructure at specified thickness locations, is performed per NORSOK MDS D51...

Open

17206

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

17207

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness max 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products...

Open

17208

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for 18.26mm wall thickness and 219.1mm OD pipe as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impac...

Open

17209

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse absorbed energy (average/single) 45 J/35 J, minimum longitudinal absorbed energy (average/single) 65 J/50 J (if transverse ...

Open

17210

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 using 20-40% NaOH or KOH solution after final polishing, fulfilling the requirement for metallographic preparation and exami...

Open

17211

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

17212

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

17213

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases as required. Source: DMV_STAN...

Open

17214

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

17215

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 includes etching to detect intermetallic phases, with findings required to be reported, and acceptance based on CVN and corrosion test results as specified in the requirement. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

17216

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10µm if not distributed over the whole specimen, but does not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed, as required by the clie...

Open

17217

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content determination per ASTM E562 or ASTM E1245 in accordance with ISO 17781. Source: DMV_STANDARD_BOOK/02 ...

Open

17218

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 at ≥400X magnification, with etching to detect intermetallic phases, nitrides, and carbides. Structure must be basically free from intermetallic precipitates; isolated precipitates allowed if not ...

Open

17219

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781/ASTM E1245 and DMV 25.7N complies. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17220

4.5

AI

No

add date

No explicit evidence of ASTM G48 Method 'A' (50˚C, 24h) corrosion testing in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

17221

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including chemical composition, ferrite content, impact, corrosion resistance, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specificatio...

Open

17222

4.5

AI

No

add date

DMV 25.7N undergoes a pitting corrosion test per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and is confirmed to comply with these criteria. Source: DMV_STANDARD_...

Open

17223

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Requirement not fulfilled based on available information. Source: DMV_STAN...

Open

17224

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions and is performed after all mechanical processing, fulfilling the requirement for 100% longitudinal defect testing. Source: DMV_STANDARD_BO...

Open

17225

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially addressed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are fulfilled. For the requested OD (219.1 mm), eddy current testing ...

Open

17226

5.2

AI

No

add date

None of the referenced documents explicitly confirm that indications greater than the calibration notch are classified as defects requiring rejection or repair, nor do they specify this acceptance criterion for NDE. Source: Digest ASTM A 790.docx, Di...

Open

17227

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with OD, WT, and ovality tolerances confirmed for the requested dimensions, and no deviations specified by the customer. Source: DMV_STANDARD_BOOK/07-01 - Gen...

Open

17228

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17229

8.0

AI

No

add date

Marking is performed according to ASTM A790 (§14) and includes heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD...

Open

17230

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

17231

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

17232

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system as specified in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 -...

Open

17233

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

17234

10.2

AI

No

add date

Certification includes EN 10204 type 3.1 with traceability to product, and MST-Tubes is ISO 9001 certified, fulfilling documentation and traceability requirements for delivered products (SIR205). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

17235

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant standards throughout. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 0...

Open

17236

4.4.1

AI

No

add date

Micrographic examination, including etching to detect intermetallic phases and ferrite balance, is performed as per ISO 17781 with 20-40% NaOH or KOH after final polishing, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

17237

10.2

AI

No

add date

No source provides all required documentation and certification details: NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and full metallurgical and non-destructiv...

Open

17238

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified for the required wall thickness. Source: Digest NORSOK MDS D51 Rev 06.docx

Open

17239

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N but not to ISO 17782; no confirmation of QTR/MPCR availability. Requirement for qualification to NORSOK M-650/ISO 17782 and documentation availability is not fully met. Source: DMV_STA...

Open

17240

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N (up to WT = 31.75 mm), and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

17241

3.1

AI

No

add date

AOD or equivalent refining is used and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17242

3.1

AI

No

add date

Chemical composition for UNS S32760 matches Table 2 requirements and is confirmed to be fulfilled for DMV material with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-0...

Open

17243

3.2

AI

No

add date

Solution annealing followed by accelerated cooling is performed per ASTM A790; manufacturing and furnace qualification are per NORSOK M-650/ISO 17782; MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured b...

Open

17244

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

17245

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

17246

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse per ASTM A790), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is performed as required. For t...

Open

17247

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with mechanical properties (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and maximum hardness verified as required by Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

17248

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

17249

4.3

AI

No

add date

Pipe wall thickness exceeds the minimum required for Charpy V-notch testing; testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible and fulfilled. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

17250

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal if transverse...

Open

17251

3.1

AI

No

add date

Chemical composition for S32760 conforms to Table 2 of ASTM A790 as required, with heat analysis performed per heat. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03-01 - Digest ASTM A 7...

Open

17252

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

17253

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

17254

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases as required. Source: DMV_STAN...

Open

17255

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

17256

4.4.2

AI

No

add date

Micrographic examination requires reporting of centerline intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

17257

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed, so the requirement is not fully met. Source: DMV_STANDARD_...

Open

17258

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, fulfilling the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-col...

Open

17259

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

17260

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% per ISO 17781 and ASTM E1245, and DMV 25.7N complies with this range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

17261

4.5

AI

No

add date

Corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is not explicitly confirmed; neither the test nor the ISO standard is referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in ...

Open

17262

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, microstructure, and ferrite requirements, with explicit compliance to ASTM A790 and NORSOK M-650/ISO 17782 qualification. Source: DM...

Open

17263

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

17264

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

17265

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 or ISO 10893-10 is available for the specified pipe dimensions, performed after all processing, with reference notches per ASTM E213 standard practice. Source: DMV_STANDARD_BOOK/12-02-03 ...

Open

17266

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no explicit evidence of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782, which may require stricter or additional NDE criteria. For the specified OD, eddy current testing is not feasib...

Open

17267

5.2

AI

No

add date

No provided document confirms that any indication greater than that produced by the calibration notch is treated as a defect requiring rejection or repair, nor that such NDE acceptance criteria are standardly applied or feasible for the requested pip...

Open

17268

6.0

AI

No

add date

Dimensional tolerances are per ASTM A790/A999 as specified in the inquiry and confirmed by the referenced documents, with no overriding TechnipFMC specification indicated. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/0...

Open

17269

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17270

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

17271

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

17272

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified, fulfilling the requirement for an appropriate quality-assurance system certified by a competent body within the EEA. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - ...

Open

17273

10.1

AI

No

add date

Manufacturer is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

17274

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

17275

10.2

AI

No

add date

No explicit confirmation that documentation traceable to the delivered products will be transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 R...

Open

17276

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued as standard and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - ...

Open

17277

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and test results—are not fully provided. Only the count...

Open

17278

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified up to the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Di...

Open

17279

1.0

AI

No

add date

Supplier is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N but not accredited to ISO 17782 as required; no evidence of QTR/MPCR availability for review or full compliance with both standards for the exact product supplied. Source: DMV_STANDARD_BO...

Open

17280

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

17281

3.1

AI

No

add date

AOD or equivalent refining is used 100% for DMV 25.7N, and chemical analysis complies with Table 2 requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

17282

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compliance with th...

Open

17283

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

17284

4.1

AI

No

add date

Tensile test specimens are sampled according to Table 3 of ASTM A790, with specified frequency and lot requirements, directly fulfilling the outlined sampling requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detail...

Open

17285

4.1

AI

No

add date

All required tests (tensile, hardness, CVN, corrosion, microstructure) are performed per NORSOK MDS D51 and ASTM A790, with correct directions and thickness locations. For the ordered pipe dimensions, transverse CVN specimens are feasible and will be...

Open

17286

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-0...

Open

17287

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required by NORSOK MDS D51 Rev 6 and ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-co...

Open

17288

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions, exceeding the minimum wall thickness required for testing. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact t...

Open

17289

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C with minimum transverse (average 45 J, single 35 J) and longitudinal (average 65 J, single 50 J if transverse not possible) values, including ...

Open

17290

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed according to ISO 17781, with etchants and electrolytic etching after final polishing as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

17291

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

17292

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10 μm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

17293

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

17294

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

17295

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

17296

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N explicitly states that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17297

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fulfilled. Source: ...

Open

17298

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_ST...

Open

17299

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

17300

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

17301

4.5

AI

No

add date

Corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is not explicitly referenced or confirmed in the provided documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

17302

4.5

AI

No

add date

DMV 25.7N meets all metallurgical property requirements and acceptance criteria per NORSOK MDS D51 Rev 6, ASTM A790, and is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

17303

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

17304

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

17305

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

17306

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE acceptance criteria are addressed. Standard NDE methods (hydrostatic, ultrasonic, eddy current) are not fully available or...

Open

17307

5.2

AI

No

add date

The available documents do not explicitly confirm that any indication greater than the calibration notch is treated as a defect requiring rejection or repair, and NDE feasibility for the specified OD is not guaranteed at the plant. Source: 02-03-01 -...

Open

17308

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no evidence of a deviation or special tolerance request in the customer specification. OD, WT, and ovality tolerances for the requested dimensions are co...

Open

17309

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17310

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot; marking methods (indelible ink, vibro-etching) include heat number and DMV lot number, ensuring traceability as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NOR...

Open

17311

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 for DMV 25.7N seamless pipe explicitly prohibits weld repairs under 'Surface finish / Repairs of defects'. Source: Digest NORSOK MDS D51 Rev 06.docx

Open

17312

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

17313

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

17314

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

17315

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number, are provided and meet the requirement for documentation traceable to delivered products. Sourc...

Open

17316

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, M-650/ISO17782 manufacturing summary/QTR number). Source: DMV_STANDARD_BOOK/...

Open

17317

10.2

AI

No

add date

No provided documentation includes all required details such as NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis results, solution annealing parameters, or complete metallurgic...

Open

17318

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, including all referenced mechanical, chemical, and testing requirements. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

17319

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782 as required; no evidence of QTR/MPCR availability for review is provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Di...

Open

17320

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Sp...

Open

17321

3.1

AI

No

add date

AOD or equivalent steel melt refinement is required and standard for MST-Tubes; DMV 25.7N meets chemical analysis per Table 2. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 ...

Open

17322

3.1

AI

No

add date

Chemical composition for UNS S32760 conforms to Table 2 of ASTM A790 as required, with heat analysis and supplier certification provided. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - ASTM A/02-03...

Open

17323

3.2

AI

No

add date

Solution annealing followed by accelerated cooling per ASTM A790 is confirmed, with manufacturing and furnace qualification per NORSOK M-650/ISO 17782. Free circulation of heating/cooling media is ensured by compliance with these standards. Source: D...

Open

17324

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot as defined in ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

17325

4.1

AI

No

add date

Tensile test specimens are sampled according to Table 3 of ASTM A790, fulfilling the requirement for test specimen sampling as outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-01 - AS...

Open

17326

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and in accordance with ASTM A790 and NORSOK MDS D51 Rev 06. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17327

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure tests at specified thickness locations. Order...

Open

17328

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

17329

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets the minimum requirements for tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as specified in NORSOK MDS D51 Rev 6 and ASTM A790 for seamless pipe. Source: DMV_STA...

Open

17330

4.3

AI

No

add date

Pipe wall thickness (18.26 mm) exceeds minimum required for Charpy V-notch testing per ASTM and ISO standards; testing feasibility confirmed for >6 mm WT. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

17331

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse 45/35 J and longitudinal 65/50 J (average/single), with sub-size specimen reduction factors applied. The specified pipe dim...

Open

17332

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, including etching for intermetallic phases and ferrite balance using the specified solution after final polishing. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

17333

4.4.1

AI

No

add date

Etching by 20 to 40% NaOH or KOH to detect ferrite balance and intermetallic phases, in accordance with ISO 17781, is specified, fulfilling the requirement for suitable etchant(s) as listed in ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Spec...

Open

17334

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

17335

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and findings are recorded with representative micrographs as required. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

17336

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

17337

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 requires reporting of intermetallic phases, with acceptance based on CVN and corrosion test results if present, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - S...

Open

17338

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is not ...

Open

17339

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

17340

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

17341

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

17342

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided in the referenced documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

17343

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties, including chemical composition, mechanical properties, impact, corrosion, microstructure, and ferrite content, as required by NORSOK MDS D51 Rev 6, ASTM A790, and NORSOK M-650/ISO ...

Open

17344

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m², fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

17345

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

17346

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

17347

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially addressed with hydrostatic or NDE (EC/UT) testing, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are met. For the requested OD...

Open

17348

5.2

AI

No

add date

No explicit confirmation of NDE acceptance criteria regarding calibration notch or disposition of indications exceeding the calibration notch; NDE methods required are not confirmed as standard for the requested OD and may only be available at extra ...

Open

17349

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790 referencing ASTM A999), and OD, WT, and ovality tolerances for the specified dimensions are stated as compliant with ASTM standards. No alternative requirements fr...

Open

17350

7.0

AI

No

add date

ASTM A790 (6.1.3) and NORSOK MDS D51 (§13) both require finished pipes to be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17351

8.0

AI

No

add date

Marking is performed according to ASTM A790, requiring full traceability to melt and heat treatment lot, with mandatory marking of heat number and DMV lot number ensuring compliance. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.d...

Open

17352

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 explicitly states 'Weld repairs not acceptable,' fulfilling the requirement that weld repairs are not acceptable. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NO...

Open

17353

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body within the EEA, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK...

Open

17354

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the quality-assurance system requirement for the material manufacturer. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/...

Open

17355

10.1

AI

No

add date

MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness, and certification will include NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR number used, fulfilling the requirement for qualification dem...

Open

17356

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable to delivered products as required by SIR205 and specification section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

17357

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control for mill inspection. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK...

Open

17358

10.2

AI

No

add date

Documentation does not provide all required details: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, full chemical analysis, solution annealing parameters, and complete metallurgical and non-de...

Open

17359

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, Digest NORSOK ...

Open

17360

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability for review as required by the specification. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS...

Open

17361

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for DMV25.7N up to WT = 31.75 mm, with manufacturing process qualified per NORSOK M-650 or ISO 17782, and compliance with NORSOK M-630 MDS D51 Rev. 6 is referenced. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

17362

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical analysis for DMV 25.7N is confirmed as compliant with Table 2. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17363

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as per ASTM A790 and NORSOK MDS D51 Rev 06. Chemical composition matches the requirement table and is confirmed by supplier certification and heat analys...

Open

17364

3.2

AI

No

add date

Heat treatment is solution annealed followed by accelerated cooling per ASTM A790, manufacturing is per NORSOK M-650/ISO 17782 qualified procedures, and furnace qualification ensures free circulation of heating/cooling media. Source: DMV_STANDARD_BOO...

Open

17365

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as required by ASTM A790 and NORSOK MDS D51 Rev 06. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

17366

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency, directly fulfilling the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Deta...

Open

17367

4.1

AI

No

add date

DMV 25.7N seamless pipes are tested per NORSOK MDS D51/ASTM A790 requirements: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure, with test locations and directions as spe...

Open

17368

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with DMV 25.7N meeting the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special prod...

Open

17369

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special...

Open

17370

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and meets the minimum wall thickness requirements of the standards. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testin...

Open

17371

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements: Charpy V-notch testing at -46°C, minimum transverse (average 45 J, single 35 J) and longitudinal (average 65 J, single 50 J) values, with reduction factors for sub-size specimens. The ...

Open

17372

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, with etching using 20-40% NaOH or KOH after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

17373

4.4.1

AI

No

add date

Etching with 20–40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BOOK/0...

Open

17374

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

17375

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included to record the presence and location of intermetallic phases. Source: DMV_STANDARD_BOOK/02...

Open

17376

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

17377

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic stringers and acceptance based on CVN and corrosion test results, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03...

Open

17378

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10µm, but does not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed, as required by the client specification. Source: DMV_STANDARD_BOOK/02-04...

Open

17379

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Sou...

Open

17380

4.4.3

AI

No

add date

Microstructure is examined per ISO 17781 at ≥400X magnification; structure must be free from intermetallic precipitates (isolated precipitates <10µm allowed, not distributed); carbides/nitrides must be reported; acceptance based on impact and corrosi...

Open

17381

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17382

4.5

AI

No

add date

No explicit confirmation or evidence that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 will be performed or is included in the referenced standards or documents. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion test...

Open

17383

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified per NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specification...

Open

17384

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

17385

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibi...

Open

17386

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is performed after all mechanical processing, heat treatments, and straightening, and the equipment supports the specified pipe dimensions. Source: DMV_STANDARD_BOOK/12 - Special Testin...

Open

17387

5.2

AI

No

add date

NDE requirements per ASTM A790 are partially addressed with hydrostatic or NDE (EC or UT) testing per ASTM A999, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE criteria are met. Eddy current t...

Open

17388

5.2

AI

No

add date

None of the relevant documents explicitly confirm that any indication greater than that produced by the calibration notch is considered a defect and that defective pipe and tubing shall be rejected or repaired; the specific acceptance criterion is no...

Open

17389

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), with no evidence of override or deviation in the customer specification. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01...

Open

17390

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17391

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods (indelible ink, vibro-etching) include heat and DMV lot numbers, ensuring compliance with the requirement. Sour...

Open

17392

9.0

AI

No

add date

NORSOK MDS D51 Rev 06, §14 states 'Weld repairs not acceptable,' fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17393

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

17394

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified, meeting the requirement for an appropriate quality-assurance system certified by a competent body. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-0...

Open

17395

10.1

AI

No

add date

Supplier MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, and certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR used, fulfilling the requirement for qualification for ...

Open

17396

10.2

AI

No

add date

ISO 9001 certification is provided and documentation is traceable to the products as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D5...

Open

17397

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

17398

10.2

AI

No

add date

No provided documentation includes all required details: NORSOK M-650/ISO 17782 identification, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and full metallurgical and non-destructive test results. ...

Open

17399

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the item table and confirmed by the digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04...

Open

17400

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV25.7N but not to ISO 17782, and there is no evidence of Qualification Test Records (QTR/MPCR) availability as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17401

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificati...

Open

17402

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent for 100% of production, and chemical analysis conforms to Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17403

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PREN ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat, confirming conformity to the required...

Open

17404

3.2

AI

No

add date

Manufacturing process is qualified to NORSOK M-650, heat treatment is solution annealed followed by accelerated cooling as per ASTM A790, and furnace compliance with NORSOK M-650/ISO 17782 is confirmed. Free circulation of heating and cooling media i...

Open

17405

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot, with 'lot' defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

17406

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for sampling requirements, fulfilling the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03...

Open

17407

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests are performed at specified thickness loc...

Open

17408

4.2

AI

No

add date

Tensile testing is performed per ASTM A370 or ISO 6892-1, and the material meets the tensile and maximum hardness properties of Table 4 for DMV 25.7N. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 -...

Open

17409

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW/32 HRC) as required by NORSOK MDS D51 Rev 6 and ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

17410

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness (>6mm), fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - ...

Open

17411

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse absorbed energy (average/single) of 45 J/35 J, minimum longitudinal absorbed energy (average/single) of 65 J/50 J (if trans...

Open

17412

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, using the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

17413

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

17414

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dig...

Open

17415

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs are included noting and recording the presence and location of intermetallic phases. So...

Open

17416

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum 400x magnification, with photos included and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

17417

4.4.2

AI

No

add date

Micrographic examination requires reporting of centerline intermetallic stringers, with acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NOR...

Open

17418

4.4.2

AI

No

add date

The specification allows isolated intermetallic precipitates below 10µm, but does not prohibit all intermetallic phases and/or precipitates when CVN testing cannot be completed, as required by the client specification. Source: DMV_STANDARD_BOOK/02-04...

Open

17419

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

17420

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 at ≥400X magnification, with etching to detect intermetallic phases, nitrides, and carbides. Acceptance criteria: structure must be basically free from intermetallic precipitates; isolated precipi...

Open

17421

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

17422

4.5

AI

No

add date

No evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

17423

4.5

AI

No

add date

DMV 25.7N meets all acceptance criteria for metallurgical properties per NORSOK MDS D51 Rev 6, including destructive, micrographic, corrosion tests, ferrite content, heat treatment, and manufacturing process requirements. Source: DMV_STANDARD_BOOK/02...

Open

17424

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781 (G48 Method A @ 50°C, 24h). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Diges...

Open

17425

5.1

AI

No

add date

No provided documentation addresses the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility...

Open

17426

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions, which are within equipment capability. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-02 - Non destructive testing/12-0...

Open

17427

5.2

AI

No

add date

NDE per ASTM A790 is confirmed, but there is no explicit evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are addressed. For the specified OD, eddy current testing is not feasible, and ultrasonic or hydrost...

Open

17428

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements, including PRE ≥ 40, as specified in Table 2 and NORSOK MDS D51 Rev 06. Heat analysis and supplier certification are performed per heat to ensure conformity with the standard....

Open

17429

5.2

AI

No

add date

The available documents do not specify that any indication greater than the calibration notch is considered a defect requiring rejection or repair, and standard NDE is not available for the requested pipe size at Montbard, so the requirement is not f...

Open

17430

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 seamless pipe are per the applicable ASTM standard (ASTM A999), with no deviations or special tolerances specified in the customer request or TechnipFMC documentation. Source: DMV_STANDARD_BOOK/07-01 - General inf...

Open

17431

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that seamless pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORS...

Open

17432

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790, requiring full traceability to melt and heat treatment lot. Marking methods include mandatory heat number and DMV lot number, ensuring traceability. Source: DMV_STANDARD_BOOK/02-03-01 - Digest AST...

Open

17433

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

17434

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

17435

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified ...

Open

17436

10.2

AI

No

add date

No explicit confirmation that documentation traceable to the delivered products will be transmitted to TechnipFMC as required by SIR205. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 R...

Open

17437

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control. Source: 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, 14-03 - Certification Montbard plant.doc

Open

17438

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing details, and all test results—are not fully prov...

Open

17439

1.0

AI

No

add date

DMV 25.7N is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK...

Open

17440

1.0

AI

No

add date

No evidence of supplier qualification to both NORSOK M-650 and ISO 17782, nor confirmation of QTR/MPCR availability for review. MST-Tubes is NORSOK M-650 accredited but not ISO 17782 accredited, which does not fully meet the requirement. Source: DMV_...

Open

17441

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

17442

3.1

AI

No

add date

Steel melt is refined with AOD or equivalent, and chemical analysis complies with Table 2 requirements for DMV 25.7N. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17443

3.2

AI

No

add date

Solution annealing followed by accelerated cooling is performed per ASTM A790; manufacturing and furnace qualification comply with NORSOK M-650/ISO 17782; free circulation of heating/cooling media is ensured by adherence to these standards. Source: D...

Open

17444

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot, with 'lot' defined as per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - S...

Open

17445

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for sampling requirements, fulfilling the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03...

Open

17446

4.1

AI

No

add date

Test sampling for seamless pipes per NORSOK MDS D51/ASTM A790 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, longitudinal if not possible), and corrosion/microstructure tests are performed at specified locations. For t...

Open

17447

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370, with required properties (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%) and maximum hardness per Table 4; DMV 25.7N complies. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02...

Open

17448

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and maximum hardness (≤310 HBW) as required by NORSOK MDS D51 Rev 6 and ASTM A790 for seamless pipe specification. Source: DMV_STANDARD_BO...

Open

17449

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for 18.26mm wall thickness and 219.1mm OD pipe as required. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impac...

Open

17450

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact requirements: Charpy V-notch testing at -46°C, minimum transverse (average 45 J, single 35 J) and longitudinal (average 65 J, single 50 J) values, with sub-size reduction factors. The specified pipe...

Open

17451

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed according to ISO 17781 with the specified etchants and electrolytic etching after final polishing as required. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

17452

4.4.1

AI

No

add date

Etching by 20% to 40% NaOH or KOH to detect ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B requirements for micrographic examination of duplex stainless steel pipes. Source: DMV_STANDARD_BOOK/02 - Speci...

Open

17453

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

17454

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORS...

Open

17455

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

17456

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers reporting and acceptance criteria. Source: DMV_STANDARD_BOOK...

Open

17457

4.4.2

AI

No

add date

No source specifies a complete prohibition of intermetallic phases and/or precipitates if CVN testing cannot be completed; only limited allowance is mentioned, not zero tolerance as required by the client specification. Source: DMV_STANDARD_BOOK/02-0...

Open

17458

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. Source: DMV_ST...

Open

17459

4.4.3

AI

No

add date

Microstructure examination is performed per ISO 17781 with etching to detect intermetallic phases, nitrides, and carbides at ≥400X magnification. Structure must be basically free from intermetallic precipitates; isolated precipitates allowed if not d...

Open

17460

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17461

4.5

AI

No

add date

No explicit confirmation that corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is performed; referenced documents do not detail this test or its method. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard...

Open

17462

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and complies with NORSOK and ASTM A790 standards. Source: DMV_STANDARD_BOOK/02 - Specifica...

Open

17463

4.5

AI

No

add date

DMV 25.7N complies with ISO 17781 G48 Method A, requiring no pitting at 20X magnification and weight loss less than 1.0 g/m². Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

17464

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in...

Open

17465

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

17466

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed; only ASTM A790/A999 NDE is detailed, which may not meet NORSOK requirements. For OD 219.1 mm, eddy current testing is not feasible, hydrostatic and ultraso...

Open

17467

5.2

AI

No

add date

None of the relevant documents confirm that indications greater than the calibration notch are treated as defects requiring rejection or repair, nor do they assure NDE capability for the specified pipe dimension at Montbard. Source: DMV_STANDARD_BOOK...

Open

17468

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standards (ASTM A999), with OD, WT, and ovality tolerances confirmed for the requested dimensions and no override by TechnipFMC indicated. Source: DMV_STANDARD_BOOK/07-01 - General...

Open

17469

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17470

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §16, both requiring full traceability to melt and heat treatment lot. Marking methods (indelible ink, vibro-etching) include heat number and DMV lot number, ensuring traceability as specified. Sour...

Open

17471

9.0

AI

No

add date

Weld repairs are explicitly not acceptable as stated in the specification under 'Surface finish / Repairs of defects'. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest...

Open

17472

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

17473

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the required quality-assurance system specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORS...

Open

17474

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

17475

10.2

AI

No

add date

ISO 9001 certification is provided and documentation traceable to delivered products is included, fulfilling the requirement for quality assurance and traceability. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

17476

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

17477

10.2

AI

No

add date

Most documentation and certification requirements are addressed except for the steel producer of the starting material, which is not fully met as only the country of origin is provided. No source provides all required specific documentation or test r...

Open

17478

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, including all mechanical, chemical, and testing requirements, and is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-03 - Dige...

Open

17479

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for DMV 25.7N but not to ISO 17782; no evidence of QTR/MPCR availability. Requirement for qualification to both NORSOK M-650/ISO 17782 and documentation availability is not fulfilled. Source: DMV_STANDARD_BOOK/0...

Open

17480

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

17481

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2 requirements. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17482

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17483

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

17484

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, with 'lot' defined as per ASTM A790, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Dige...

Open

17485

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for test specimen sampling, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03-...

Open

17486

4.1

AI

No

add date

Test sampling for seamless pipes, including tensile (longitudinal or transverse), hardness, CVN (transverse or longitudinal if not possible), and corrosion/microstructure at specified thickness locations, is performed per NORSOK MDS D51/ASTM A790. Fo...

Open

17487

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370/ISO 6892-1, with results meeting Table 4 requirements (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%). Hardness testing is performed per ASTM A790, with results provided. Source: DMV_STANDARD_BO...

Open

17488

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 requirements: tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and hardness ≤ 310 HBW (32 HRC). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

17489

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and standards; requirement is fulfilled. Source: DMV_STANDARD_BOOK/12-03-02 - Impact Test for hot finished products.doc

Open

17490

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C, minimum absorbed energies (transverse: 45 J average/35 J single; longitudinal: 65 J average/50 J single if transverse not possible), and sub-s...

Open

17491

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed according to ISO 17781, with specified etchants and electrolytic etching after final polishing, as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 ...

Open

17492

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution to show ferrite balance and intermetallic phases, as listed in ISO 17781 Appendix B, is specified for micrographic examination. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

17493

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

17494

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are reported as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Di...

Open

17495

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, at or near mid-wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/...

Open

17496

4.4.2

AI

No

add date

Micrographic examination requires reporting of centerline intermetallic stringers and acceptance based on CVN and corrosion test results. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSO...

Open

17497

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed due to geometry or size. Therefore, the requirement is...

Open

17498

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Sou...

Open

17499

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

17500

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in accordance with ISO 17781 and ASTM E1245, and DMV 25.7N complies within this range. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

17501

4.5

AI

No

add date

Corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is not explicitly confirmed in the available documentation; referenced standards do not provide direct evidence of fulfillment. Source: DMV_STANDARD_BOOK/12-03-01- Cor...

Open

17502

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements, and is qualified per NORSOK M-650/ISO 17782. Source: DMV_STANDARD_BOOK/02 - Specifications...

Open

17503

4.5

AI

No

add date

DMV 25.7N undergoes pitting corrosion testing per ISO 17781 (G48 Method A, 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss less than 1.0 g/m², and complies with these criteria. Source: DMV_STANDARD_BOOK/02 - Spe...

Open

17504

5.1

AI

No

add date

No evidence is provided regarding NDE personnel qualification or certification to ISO 9712 level II or III, nor about their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility in...

Open

17505

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions and performed after all mechanical processing, meeting the requirement for 100% longitudinal defect testing and reference notch calibratio...

Open

17506

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 are partially addressed (hydrostatic or EC/UT per ASTM A999), but there is no evidence that NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782-specific NDE requirements are fulfilled. For OD 219.1 mm, eddy curr...

Open

17507

5.2

AI

No

add date

None of the referenced documents explicitly confirm that any indication greater than that produced by the calibration notch is treated as a defect, nor do they specify that defective pipe and tubing shall be rejected or repaired according to this cri...

Open

17508

6.0

AI

No

add date

Dimensional tolerances for ASTM A790 pipe are per the applicable ASTM standard (ASTM A999), including OD, WT, and ovality, with no evidence of special tolerance requests or deviations in the customer specification or TechnipFMC documentation. Source:...

Open

17509

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 6 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-04-03 - Digest NORSO...

Open

17510

8.0

AI

No

add date

Marking per ASTM A790 and NORSOK MDS D51 Rev 6 requires heat and lot traceability; marking methods at Montbard include mandatory heat and DMV lot numbers, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 -...

Open

17511

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' for DMV 25.7N seamless pipe. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 -...

Open

17512

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

17513

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

17514

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N up to the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Speci...

Open

17515

10.2

AI

No

add date

Certification includes EN 10204 type 3.1 with traceability to heat treatment, steel manufacturer, melting/refining practice, and NORSOK M-650/ISO 17782 qualification; documentation is traceable to delivered products as required by SIR205. Source: DMV...

Open

17516

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are issued and include all information required by ASTM A790 and NORSOK M-630, validated by Quality Control and referencing relevant qualification standards. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Re...

Open

17517

10.2

AI

No

add date

Required documentation and certification details—including NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis, solution annealing parameters, and results of all metallurgical and...

Open

17518

1.0

AI

No

add date

DMV 25.7N seamless pipes are fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as confirmed by the item table and specification digest. Manufacturing is M-650 qualified for the required wall thickness. Source: Item Table, Digest NORSOK ...

Open

17519

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N (up to WT = 31.75 mm) but not to ISO 17782; no confirmation of QTR/MPCR availability for review. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17520

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

17521

3.1

AI

No

add date

AOD or equivalent refining is standard for 100% of production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17522

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition requirements in Table 2, including PRE ≥ 40, as specified in ASTM A790 and NORSOK MDS D51 Rev 06. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17523

3.2

AI

No

add date

Solution annealing followed by accelerated cooling is performed per ASTM A790; manufacturing and furnaces are qualified to NORSOK M-650/ISO 17782; free circulation of heating/cooling media is ensured by compliance with these standards. Source: DMV_ST...

Open

17524

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

17525

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with specified frequency per lot and piece, matching the requirement for test specimen sampling outlined in Table 3. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03...

Open

17526

4.1

AI

No

add date

DMV 25.7N seamless pipes are tested per NORSOK MDS D51/ASTM A790 requirements: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), corrosion, and microstructure, with sampling locations and directions as...

Open

17527

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-0...

Open

17528

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets minimum tensile strength ≥ 750 MPa, yield strength ≥ 550 MPa, elongation ≥ 25%, and maximum hardness 310 HBW as required by NORSOK MDS D51 Rev 6 and ASTM A790. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Re...

Open

17529

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370, ASTM A1058, or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness (>6mm), fulfilling the requirement. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - ...

Open

17530

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements: Charpy V-notch testing at -46°C, minimum transverse (average/single) 45J/35J, minimum longitudinal (average/single) 65J/50J, and reduction factors for sub-size specimens. The...

Open

17531

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed according to ISO 17781, with etchants and electrolytic etching after final polishing as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special ...

Open

17532

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution for micrographic examination to show ferrite balance and intermetallic phases is specified, in accordance with ISO 17781 Appendix B. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - ...

Open

17533

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781, with acceptance criteria requiring the structure to be basically free from intermetallic precipitates; isolated precipitates are allowed if not distributed throughout the specimen and each is below...

Open

17534

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 with etching to detect intermetallic phases at a minimum magnification of 400x, and representative micrographs and findings are recorded and reported. Source: DMV_STANDARD_BOOK/02 - Specifications-D...

Open

17535

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos included in the report showing actual magnification and a scale bar, fulfilling the requirement for a representative micrograph at or near mid-wall thickness. Sourc...

Open

17536

4.4.2

AI

No

add date

Micrographic examination per ISO 17781 requires reporting of intermetallic stringers, with acceptance based on CVN and corrosion test results as specified. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04...

Open

17537

4.4.2

AI

No

add date

The digest allows isolated intermetallic precipitates below 10μm, while the requirement prohibits all intermetallic phases and/or precipitates if CVN testing cannot be completed. The stricter client requirement is not fully met. Source: DMV_STANDARD_...

Open

17538

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content measurement methods and standard compliance. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-colle...

Open

17539

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781 with etching methods, magnification, and acceptance criteria (structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported); acceptance based on impact and...

Open

17540

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17541

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) performed in accordance with ISO 17781 is provided. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

17542

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 06, including tensile, impact, corrosion, ferrite content, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special p...

Open

17543

4.5

AI

No

add date

DMV 25.7N is tested per ISO 17781 (G48 Method A @ 50°C, 24h) with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and complies with these requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection...

Open

17544

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

17545

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

17546

3.1

AI

No

add date

AOD or equivalent refining is required and standard for production, and chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17547

5.2

AI

No

add date

NDE per ASTM A790 is partially aligned via hydrostatic or EC/UT per ASTM A999, but there is no evidence of compliance with NORSOK M-630 MDS D51 Rev 6 or NORSOK M-650/ISO 17782. For OD 219.1 mm, eddy current testing is not feasible at Montbard, and hy...

Open

17548

5.2

AI

No

add date

No explicit confirmation of calibration notch-based NDE acceptance criteria; standard NDE not available for OD 219.1 mm at Montbard, so requirement cannot be fulfilled for this size. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx, ...

Open

17549

6.0

AI

No

add date

Dimensional tolerances for OD, WT, and ovality are per ASTM A790 and referenced ASTM A999, with no deviations specified in the customer requirements, fulfilling the requirement for ASTM standard tolerances unless otherwise stated. Source: DMV_STANDAR...

Open

17550

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both specify that finished pipes shall be white pickled or bright annealed, fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17551

8.0

AI

No

add date

Marking per ASTM A790 and plant procedures includes mandatory marking of heat number and DMV lot number, ensuring full traceability to melt and heat treatment lot. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_B...

Open

17552

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

17553

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

17554

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers as specified in section 10.0. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02...

Open

17555

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV25.7N (UNS S32760) up to the required wall thickness for the specified size and product form. Source: DMV_STANDARD_BOO...

Open

17556

10.2

AI

No

add date

ISO 9001 certification and EN 10204 type 3.1 certificates are provided, ensuring documentation is traceable and transmitted as required by SIR205. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Dig...

Open

17557

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630, validated by Quality Control. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx, DMV_STANDARD_BOOK/14-03 - Certificati...

Open

17558

10.2

AI

No

add date

Documentation and certification requirements are not fully met: NORSOK M-650/ISO 17782 identification, steel melting practice, refining method, heat number, chemical analysis, solution annealing details, and all required test results are addressed ex...

Open

17559

1.0

AI

No

add date

DMV 25.7N seamless pipe is specified as compliant with ASTM A790 and NORSOK M-630 MDS D51 Rev 6, with M-650 qualification confirmed for the required wall thickness. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special produ...

Open

17560

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 for UNS S32760 / DMV 25.7N but not to ISO 17782; no evidence of QTR/MPCR documentation availability. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17561

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified according to NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - S...

Open

17562

3.2

AI

No

add date

Solution annealing followed by accelerated cooling per ASTM A790 is confirmed; manufacturing process and furnaces are qualified per NORSOK M-650/ISO 17782; free circulation of heating/cooling media is implicit in compliance with these standards. Sour...

Open

17563

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed per heat and heat treatment lot, as defined in ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

17564

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for sampling requirements, fulfilling the specification for test specimen sampling. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-...

Open

17565

4.1

AI

No

add date

Test sampling requirements for seamless pipes per NORSOK MDS D51/ASTM A790, including tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests, with specified locations and ...

Open

17566

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, with mechanical properties meeting Table 4 requirements (Rp0.2 ≥ 550 MPa, Rm ≥ 750 MPa, A ≥ 25%). Hardness testing is also performed and results are provided. Source: DMV_S...

Open

17567

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets NORSOK MDS D51 Rev 6 mechanical requirements: yield ≥ 550 MPa, tensile ≥ 750 MPa, elongation ≥ 25%, hardness ≤ 310 HBW/32 HRC for S32760, matching client specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest...

Open

17568

4.3

AI

No

add date

Charpy V-notch testing per ASTM A370 or ISO 148-1 is feasible for the specified pipe dimensions and wall thickness. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-02 - Impact tests in Montbard...

Open

17569

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 6 impact property requirements: Charpy V-notch testing at -46°C with minimum absorbed energies of 45 J (average) and 35 J (single) transverse, and 65 J (average) and 50 J (single) longitudinal (if transverse...

Open

17570

4.4.1

AI

No

add date

Micrographic examination of 25 Cr Duplex stainless steels is performed in accordance with ISO 17781, with etching using 20-40% NaOH or KOH after final polishing, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collect...

Open

17571

4.4.1

AI

No

add date

Etching with 20–40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases, fulfilling the requirement. Source: DMV_STANDARD_BOOK/0...

Open

17572

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates are allowed if not homogeneously distributed and each is below 10µm, matching the requirement exactly. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

17573

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781 at a minimum magnification of 400x, with etching to detect intermetallic phases; presence and location are noted and recorded with micrographs. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-c...

Open

17574

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at actual magnification and a scale bar, at or near mid-wall thickness if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

17575

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

17576

4.4.2

AI

No

add date

The referenced specification allows isolated intermetallic precipitates below 10μm, while the requirement prohibits any intermetallic phases and/or precipitates if CVN testing cannot be completed. Therefore, the requirement is not fulfilled by the av...

Open

17577

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or by image analysis according to ASTM E1245 in accordance with ISO 17781. ...

Open

17578

4.4.3

AI

No

add date

Micrographic examination acceptance criteria are specified: etching methods, minimum 400X magnification, structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides to be reported, and compliance with impact and cor...

Open

17579

4.4.3

AI

No

add date

Ferrite content is specified as 35% to 60% in compliance with ISO 17781 and ASTM E1245 for DMV 25.7N, fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

17580

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

17581

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, microstructure, and ferrite requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

17582

4.5

AI

No

add date

Corrosion test for DMV 25.7N is performed per ISO 17781: G48 Method A at 50°C for 24 hours, with acceptance criteria of no pitting at 20X magnification and weight loss < 1.0 g/m², and DMV 25.7N complies with these criteria. Source: DMV_STANDARD_BOOK/...

Open

17583

5.1

AI

No

add date

No evidence is provided regarding the qualification or certification of NDE personnel to ISO 9712 level II or III, nor their roles and responsibilities as defined in ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testing feasibility i...

Open

17584

5.2

AI

No

add date

100% ultrasonic testing for longitudinal defects per ASTM E213 and ISO 10893-10 is available, and the specified pipe dimensions are within equipment capability. Source: DMV_STANDARD_BOOK/12-02-03 - Ultrasonic testing in DMV - D.doc

Open

17585

5.2

AI

No

add date

NDE acceptance criteria per NORSOK M-630 MDS D51 and NORSOK M-650/ISO 17782 are not confirmed; only ASTM A790/A999 NDE is detailed. For OD 219.1 mm, eddy current testing is not feasible, and hydrostatic/ultrasonic tests are only available at extra co...

Open

17586

5.2

AI

No

add date

None of the referenced documents explicitly confirm that indications greater than the calibration notch are classified as defects requiring rejection or repair per NDE criteria for ASTM A790/NORSOK MDS D51 pipes and tubes. Source: DMV_STANDARD_BOOK/0...

Open

17587

6.0

AI

No

add date

Dimensional tolerances are per the applicable ASTM standard (ASTM A790 referencing ASTM A999), with no deviations or special tolerances specified by TechnipFMC. Source: DMV_STANDARD_BOOK/07.01 - General information.doc, DMV_STANDARD_BOOK/07.03.01 - T...

Open

17588

7.0

AI

No

add date

ASTM A790 section 6.1.3 and NORSOK MDS D51 Rev 06 §13 both require finished pipes to be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17589

8.0

AI

No

add date

Marking is performed per ASTM A999 §25 and ASTM A790 §14, both requiring full traceability to melt and heat treatment lot. Marking methods (indelible ink, vibro-etching) include heat and DMV lot numbers, ensuring compliance with the requirement. Sour...

Open

17590

9.0

AI

No

add date

Weld repairs are not acceptable as explicitly stated under 'Surface finish / Repairs of defects' (§13, §14) for DMV 25.7N seamless pipe per NORSOK MDS D51 Rev 6 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Sp...

Open

17591

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

17592

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, fulfilling the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - ...

Open

17593

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the qualification requirement for the specified size...

Open

17594

10.2

AI

No

add date

Certification includes EN 10204 type 3.1 with traceability to heat treatment, steel manufacturer, melting/refining practice, and NORSOK M-650/ISO17782 Manufacturing Summary or QTR number; documentation is traceable to delivered products as required b...

Open

17595

10.2

AI

No

add date

EN 10204 Type 3.1 certificates are standard and include all information required by ASTM A790 and NORSOK M-630, with validation by Quality Control and reference to the relevant standards in the documentation process. Source: 02-04-03 - Digest NORSOK ...

Open

17596

10.2

AI

No

add date

No evidence is provided for NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, steel melting practice and refining method, heat number, actual chemical analysis results, solution annealing temperature/holding time/quench medium...

Open

17597

1.0

AI

No

add date

DMV 25.7N seamless pipe is fully compliant with ASTM A790 and NORSOK M-630 MDS D51 rev. 6, as specified in the item table and confirmed by the digest. Manufacturing is M-650 qualified for the required wall thickness. Source: DMV_STANDARD_BOOK/02-04-0...

Open

17598

1.0

AI

No

add date

Supplier is accredited to NORSOK M-650 but not ISO 17782, and there is no confirmation of QTR/MPCR availability for review as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Rev 06.docx

Open

17599

3.0

AI

No

add date

MST-Tubes is NORSOK M-650 accredited for UNS S32760 / DMV 25.7N up to WT = 31.75 mm, and the manufacturing process is qualified per NORSOK M-650 or ISO 17782, meeting NORSOK M-630 MDS D51 rev. 6 requirements. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

17600

3.1

AI

No

add date

AOD or equivalent steel melt refining is standard practice and required for 100% of production; chemical composition for DMV 25.7N is confirmed as compliant with Table 2. Source: 02-03-01 - Digest ASTM A 790.docx, 02-04-03 - Digest NORSOK MDS D51 Rev...

Open

17601

3.1

AI

No

add date

DMV 25.7N (UNS S32760) complies with the chemical composition limits and PREN requirements specified in Table 2, matching ASTM A790 and NORSOK MDS D51 Rev 6 standards. Source: DMV_STANDARD_BOOK/02-03-01 - Digest ASTM A 790.docx, DMV_STANDARD_BOOK/02-...

Open

17602

3.2

AI

No

add date

Pipes are solution annealed followed by accelerated cooling per ASTM A790, with manufacturing and furnaces qualified to NORSOK M-650/ISO 17782. MST-Tubes is M-650 accredited for DMV 25.7N. Free circulation of heating/cooling media is ensured by compl...

Open

17603

4.1

AI

No

add date

One set of impact, tensile, hardness, corrosion testing, and microstructure examinations is performed for each heat and heat treatment lot, with lot defined per ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Specia...

Open

17604

4.1

AI

No

add date

Tensile test specimens are sampled as per Table 3 of ASTM A790, with explicit reference to Table 3 for sampling requirements, fulfilling the specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-03 - Detailed digests/02-03...

Open

17605

4.1

AI

No

add date

Test sampling for seamless pipes (DMV 25.7N) per ASTM A790 and NORSOK MDS D51 is fulfilled: tensile (longitudinal or transverse), hardness, CVN (transverse, or longitudinal if not possible), and corrosion/microstructure tests at specified thickness l...

Open

17606

4.2

AI

No

add date

Tensile testing is performed at room temperature per ASTM A370 or ISO 6892-1, and DMV 25.7N meets the required tensile and maximum hardness properties of Table 4. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special product...

Open

17607

4.2

AI

No

add date

DMV 25.7N (UNS S32760) meets the minimum requirements for tensile strength (≥750 MPa), yield strength (≥550 MPa), elongation (≥25%), and hardness (≤310 HBW) as specified in NORSOK MDS D51 Rev 6 and ASTM A790. Source: DMV_STANDARD_BOOK/02 - Specificat...

Open

17608

4.3

AI

No

add date

Charpy V-notch testing is feasible for the specified pipe dimensions and meets ASTM A370 and ISO 148-1 requirements for minimum wall thickness. Source: DMV_STANDARD_BOOK/12 - Special Testing/12-03 - Destructive testing/12-03-02 - Impact tests/12-03-0...

Open

17609

4.3

AI

No

add date

DMV 25.7N complies with NORSOK MDS D51 Rev 06 impact property requirements at -46°C, with minimum absorbed energy values for both transverse and longitudinal directions, and the specified pipe dimensions allow for required testing orientations and sp...

Open

17610

4.4.1

AI

No

add date

Micrographic examination, including etching for intermetallic phases and ferrite balance, is performed as per ISO 17781 using 20-40% NaOH or KOH after final polishing, fulfilling the requirement for metallographic preparation and examination with the...

Open

17611

4.4.1

AI

No

add date

Etching with 20% to 40% NaOH or KOH solution or other suitable etchant(s) as listed in ISO 17781 Appendix B is required for micrographic examination to show ferrite balance and intermetallic phases. Source: DMV_STANDARD_BOOK/02 - Specifications-Diges...

Open

17612

4.4.2

AI

No

add date

Microstructure must be basically free from intermetallic precipitates; isolated precipitates allowed if not distributed over the whole specimen and if each is below 10µm, matching the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-...

Open

17613

4.4.2

AI

No

add date

Micrographic examination is performed per ISO 17781, with etching to detect intermetallic phases at a minimum magnification of 400x, and micrographs are included noting and recording the presence and location of intermetallic phases. Source: DMV_STAN...

Open

17614

4.4.2

AI

No

add date

Micrographic examination is performed at a minimum magnification of 400x, with photos at or near mid-wall thickness, actual magnification reported, and scale bar included if intermetallic phases are not detected. Source: DMV_STANDARD_BOOK/02 - Specif...

Open

17615

4.4.2

AI

No

add date

Micrographic examination requires reporting of intermetallic phases and acceptance based on CVN and corrosion test results, fulfilling the requirement for centerline intermetallic stringers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collec...

Open

17616

4.4.2

AI

No

add date

The referenced document allows isolated intermetallic precipitates below 10μm, while the requirement prohibits all intermetallic phases and/or precipitates if CVN testing cannot be completed. No source fully prohibits intermetallics as required. Sour...

Open

17617

4.4.3

AI

No

add date

Ferrite content is determined as per ISO 17781, using ASTM E1245 by default and ASTM E562 on request, matching the requirement for ferrite content determination per ASTM E562 or image analysis according to ASTM E1245 in accordance with ISO 17781. Sou...

Open

17618

4.4.3

AI

No

add date

Micrographic examination is specified per ISO 17781, with etching, magnification, and acceptance criteria: structure free from intermetallic precipitates, isolated precipitates <10µm, carbides/nitrides reported; acceptance based on impact and corrosi...

Open

17619

4.4.3

AI

No

add date

Ferrite content requirement of 35% to 60% is met for DMV 25.7N grade as per NORSOK MDS D51 Rev 06 specification. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Digest NORSO...

Open

17620

4.5

AI

No

add date

No explicit evidence of corrosion testing per ASTM G48 Method 'A' (50˚C, 24h) in accordance with ISO 17781 is provided or referenced in the relevant documentation. Source: DMV_STANDARD_BOOK/12-03-01- Corrosion tests in Montbard plant.docx

Open

17621

4.5

AI

No

add date

DMV 25.7N meets all metallurgical acceptance criteria per NORSOK MDS D51 Rev 6, including tensile, impact, corrosion, ferrite, and microstructure requirements. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/0...

Open

17622

4.5

AI

No

add date

DMV 25.7N meets the requirements of no pitting at 20X magnification and weight loss less than 1.0 g/m² per ISO 17781 (G48 Method A @ 50°C, 24h). Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Diges...

Open

17623

5.1

AI

No

add date

No evidence that NDE personnel are qualified and certified to level II or III in accordance with ISO 9712 or equivalent, or that their roles and responsibilities are defined as per ISO 9712. Source: DMV_STANDARD_BOOK/12-02-01 - Non destructive testin...

Open

17624

5.2

AI

No

add date

Ultrasonic testing in accordance with ASTM E213 and ISO 10893-10 is available for the specified pipe dimensions and performed after all mechanical processing, heat treatments, and straightening. Reference notches are introduced per ASTM E213 Figure 3...

Open

17625

5.2

AI

No

add date

NDE acceptance criteria per ASTM A790 and NORSOK M-630 MDS D51/ISO 17782 are not fully met: only general feasibility for eddy current and ultrasonic testing is confirmed for the specified OD and length, but not that required NDE is performed or accep...

Open

17626

5.2

AI

No

add date

The specific NDE acceptance criterion that any indication greater than that produced by the calibration notch represents a defect, requiring rejection or repair, is not confirmed in the referenced documents. NDE methods are mentioned, but the require...

Open

17627

6.0

AI

No

add date

Dimensional tolerances are confirmed to be per the applicable ASTM standard (ASTM A790/A999) for the specified product dimensions, fulfilling the requirement unless otherwise stated by the client. Source: DMV_STANDARD_BOOK/07-01 - General information...

Open

17628

7.0

AI

No

add date

ASTM A790 and NORSOK MDS D51 Rev 06 both specify that finished pipes shall be white pickled or bright annealed, directly fulfilling the requirement. Source: Digest ASTM A 790.docx, Digest NORSOK MDS D51 Rev 06.docx

Open

17629

8.0

AI

No

add date

Marking per ASTM A790 includes full traceability to melt and heat treatment lot, and standard plant marking methods (indelible ink, vibro-etching) include heat and lot numbers as required. Source: DMV_STANDARD_BOOK/02-04-03 - Digest NORSOK MDS D51 Re...

Open

17630

9.0

AI

No

add date

NORSOK MDS D51 Rev 06 explicitly states 'Weld repairs not acceptable' under 'Surface finish / Repairs of defects', fulfilling the requirement. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest ...

Open

17631

10.0

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the requirement for an appropriate quality-assurance system. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-03 - Dig...

Open

17632

10.1

AI

No

add date

MST-Tubes is ISO 9001 certified by a competent body, meeting the quality-assurance system requirement for material manufacturers. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-04 - Special products/02-04-03 - Digest NORSOK/02-04-...

Open

17633

10.1

AI

No

add date

Certification includes NORSOK M-650/ISO 17782 Manufacturing Summary identification or QTR, and MST-Tubes is M-650 accredited for DMV 25.7N (UNS S32760) up to the required wall thickness, fulfilling the requirement for qualification for the specified ...

Open

17634

10.2

AI

No

add date

ISO 9001 certification and traceable documentation, including EN 10204 type 3.1 certificates and NORSOK M-650/ISO17782 manufacturing summary or QTR number, are provided as required. Source: DMV_STANDARD_BOOK/02 - Specifications-Digest-collection/02-0...

Open

17635

10.2

AI

No

add date

EN 10204 Type 3.1 certificate is provided and includes all information required by ASTM A790 and NORSOK M-630 (heat treatment, steel manufacturer, melting/refining practice, and M-650/ISO17782 manufacturing summary/QTR number). Source: DMV_STANDARD_B...

Open

17636

10.2

AI

No

add date

No provided documentation includes all required items: NORSOK M-650/ISO 17782 identification or QTR/MPCR number, steel producer, melting practice, heat number, chemical analysis (ladle), solution annealing parameters, and results of all metallurgical...

Open

KAM OG 25-14535-00 - 2025-07-25 00:00:00 - VOESTALPINE